Upload
others
View
5
Download
0
Embed Size (px)
Citation preview
Thermofoil PROInstallation GuideYOUR STEP-BY-STEP GUIDE TO THE PERFECT INSTALLATION
PLEASE ENSURE YOU HAVE READ AND FULLY UNDERSTOOD THIS GUIDE BEFORE INSTALLATION!!
TFPIG1
WWW. WWW. WWW. WWW. WWW. WWW.
If you have any questions or queries regarding this product, or any other products or servicesCall our technical helpline for free on 0800 019 5899
INSTALLATION GUIDE: THERMOFOIL PRO
2
Thank you for your purchase...
WWW.Browse our full product range, watch videos, download product literature and get a quote, all on the Thermogroup UK website.
WWW.THERMOGROUPUK.COM
CONTACT US ONLINE
WWW.0800 019 5899
CONTACT US BY PHONE
WWW.
CONTACT US BY MAIL
Thermogroup UK, Bridge House, Hop Pocket Lane, Paddock Wood, Kent. TN12 6DQ.
Got a question or query? Call our UK support line free from your land line.Open 07:30 – 16:30 Mon - Fri
Need to find us or want to write a letter to say hello? Feel free to contact us at Bridge House.
Thank you for choosing a Thermogroup UK product. Our commitment to simple,
honest, on-time quality service ensures that we are here to help throughout every
stage of your project from idea to installation and, most importantly, after sales
support.
This document will provide a step-by-step guide to a perfect installation as well
as details on your warranty and how to get Technical Support should you need it.
To ensure a safe, hassle-free installation to be proud of please take the time to read
this guide in full before you start. We’ve taken the time to highlight any potential
pitfalls and common errors so you can avoid them and get the job done!
This product is covered by a 15 Year Warranty, subject to terms and conditions. Be
sure to keep your receipt as proof of purchase, this will be required to validate your
5 Year Warranty.
Please complete the Customer Handover section on page 11 in full so that your
customer has all the information they need to complete the online warranty form
and register their Thermofoil PRO Heating Mat 15 year Warranty.
If you have any questions about your Thermofoil PRO Heating Mat or any of our
other products call our technical Support team on the freephone number below. We
will do our best to find a solution and will always give that little bit extra…
Thanks again for choosing Thermogroup UK products.
The Thermogroup UK 15 Year Warranty guarantees Thermofoil PRO Heating Mat
to remain free from defects in workmanship and materials under normal use and
maintenance, and is guaranteed to remain in full working order subject to the
conditions and limitations below:
Thermofoil PRO Heating Mat are guaranteed for the lifetime of the floor covering
under which it is originally fitted subject to the following conditions. Please pay
attention to the exclusions listed at the end of this guarantee.
Thermogroup UK (TGUK) 15 Year Warranty applies:
1. Only if the product is registered, and that the registration information is received
and documented by Thermogroup UK, within 60 Days after purchase. You can
register your product by completing the form online at www.thermogroupuk.com.
Proof of purchase must be presented to make a claim, so please ensure that you
keep a copy of both your invoice and purchase receipt in a safe place. Such invoice/
receipt should clearly state the model that has been purchased and be in legible
condition so as to aid in identifying the system; and
2. Only if the Thermofoil PRO Heating Mat has been properly earthed and protected
by a Residual Current Device (RCD) at all times.
This guarantee does not cover any thermostats as these are covered by a separate 3
year warranty from the date of purchase, except as provided below.
All Thermogroup UK warranties become void if the floor covering under which the
Thermofoil PRO Heating Mat is originally fitted is damaged, lifted, replaced, repaired
or covered with additional layers of flooring, after a 15 year period from purchase.
You do not get this 15 year period with any other manufacturer guarantee. The
Thermogroup UK 15 Year Warranty does not cover accidental damage, including but
not limited to damage caused by lifting, replacing, repairing the original covering
laid after installation.
The guarantee period starts on the date of purchase but the registration is only
confirmed only when a letter or email of confirmation is sent by Thermogroup UK.
Should it be required, Thermogroup UK will arrange for the Thermofoil PRO Heating
Mat to be repaired or (at the discretion of TGUK) have parts replaced free of charge.
The cost of repair will only cover the cost of replacement TGUK parts and/or repair
to damaged TGUK parts and products. Any damage to floor coverings or floors, costs
of re-laying or repairing floors or floor coverings are not covered by the Thermogroup
UK 15 Year Warranty.
Please Note: Full Terms and Conditions are available on request.
Email [email protected] to request your copy or give us a call.
Warranty, Terms & ConditionsA message from customer care
TFPIG1
WWW. WWW. WWW. WWW. WWW. WWW. If you have any questions or queries regarding this product, or any other products or servicesyou can view our complete range online, WWW.THERMOGROUPUK.COM
INSTALLATION GUIDE: THERMOFOIL PRO
3
Contents
Warning: Regulations and guidelines 4
Warning: Do’s and don’ts 4
Preparation: How to cut, turn and position Thermofoil PRO mats 5
Step 3: Carpet and vinyl floors - Heat Pak 10
8Step 1: How to lay Thermofoil PRO mats
11Finalise: Customer handover and trouble shooting
Preparation: Test procedure 5
Step 2: Lay laminate flooring & install thermostat 9
Planning: Layout and calculations 6
Planning: Floor finish option 7
Stage 1: Preparation and Planning
Stage 2: Installation
Stage 3: Testing & Customer Handover
6 - 7
6 - 7
6 - 7
5-7
8-10
11
Warnings: The Do’s and Don’ts 6 - 74
TFPIG1
WWW. WWW. WWW. WWW. WWW. WWW.
If you have any questions or queries regarding this product, or any other products or servicesCall our technical helpline for free on 0800 019 5899
INSTALLATION GUIDE: THERMOFOIL PRO
4
! BEFORE YOU START !
Thermofoil PRO™ is fully CE approved, certified and manufactured to the highest standards using state of the art Fluropolymer coated cables. All our cables and mats are designed to be 17th Edition Part P compliant and the instructions we supply with them include as much information as possible to ensure that all installations comply with them. Please call our freephone customer care line if in any doubt on 0800 019 5899.
ALL WIRING MUST CONFORM TO IEE 17TH EDITION PART P REGULATIONS
! IMPORTANT SAFETY REGULATIONS !
DO NOTDOUSE THE FOIL HEATING MATS WITH GLUED LOCKING SYSTEMS OR LAMINATES THAT HAVE AN UNDERPAD OR CUSHION MATERIAL PRE-ATTACHED TO THE UNDERSIDE
INSTALL FOIL MATS UNDER WALLS OR PARTITIONS, OR IN AREAS UNDER HEAVY CABINETS, CLOSETS, OR FIXTURES (TOILETS, SINKS, TUBS, ETC.)
INSTALL OVER FLOORS THAT HAVE TRACES OF MOISTURE, ARE UNEVEN OR OVER CARPETS OR PARQUET FLOOR
LEAVE INSULATING MATERIALS SUCH AS BEAN BAGS; LINEN OR TOWELS ON THE FLOOR SURFACE
PLACE HEAVY/SHARP TOOLS (OR ANY OTHER POTENTIALLY DAMAGING OBJECT) ON TOP OF THE HEATING MATS
INSTALL FOIL MATS WITHIN APPROXIMATELY 50MM OF ANY HEAT CONDUCTIVE BUILDING PART, SUCH AS COLD WATER PIPES
INSTALL FOIL MATS WITHIN 20MM OF ONE ANOTHER, 50MM OF ANY WALL OR 100MM OF A FIREPLACE OR HOT WATER PIPE
INSTALL FOIL HEATING MATS UNDER WOODEN FLOOR, IF THE FLOOR IS THICKER THAN 18MM
INSTALL ELECTRICAL CABLES OR PIPES UNDER THE FLOOR WITH THE FOIL HEATING MATS
PLACE ITEMS ON THE FLOOR SURFACE WHICH WILL STOP THE AIR FLOW OR NOT ALLOW HEAT TO RISE INTO THE ROOM
INSTALL THE FOIL HEATER UP STEPS
OVERLAP HEATING MATS, FOLD OR WRINKLE THE FOIL HEATING MATS
WALK UNNECESSARILY ON THE FOIL HEATING MATS
INSTALL MATS WHEN THE ROOM TEMPERATURE IS BELOW -50C
INSTALL FOIL HEATING MATS ANYWHERE EXCEPT INSIDE BUILDINGS
CHECK WITH THE MANUFACTURER OF YOUR FLOORING, THAT THEIR PRODUCTS ARE COMPATIBLE WITH ELECTRIC FLOOR HEATING SYSTEMS
ENSURE THAT A HEAT LOSS CALCULATION HAS BEEN CARRIED OUT AND HEATING REQUIREMENTS HAVE BEEN MET IF YOU ARE USING THE FOIL HEATING SYSTEM AS A PRIMARY SOURCE OF HEATING
ENSURE THAT THE CUSTOMER HANDOVER FORM (P11) IS COMPLETED AND GIVEN TO THE CUSTOMER WITH ANY PLANS AND TEST RESULTS IN ACCORDANCE WITH 17TH EDITION WIRING REGULATIONS
OPERATE THE HEATING MAT WITH A THERMOGROUP FLOOR SENSOR THERMOSTAT TO ENSURE THE FLOOR DOES NOT EXCEED THE MAXIMUM RECOMMENDED TEMPERATURE (USUALLY 27°C)
ZONE EACH HEATED ROOM WITH ITS OWN THERMOSTAT CONTROLLER. THIS ALLOWS EACH ROOM TO BE CONTROLLED INDIVIDUALLY SAVING YOU ENERGY BY ONLY HEATING THE ZONE WHEN REQUIRED. EACH THERMOGROUP THERMOSTAT HAS A MAXIMUM CAPACITY OF 16 AMPS
INSTALL INSULATION / UNDERLAY BELOW THE HEATING MATS TO PREVENT DAMAGE WHEN THE WEIGHT OF THE FLOOR FURNITURE ETC IS ADDED. MAKE SURE UNAVOIDABLE WOODEN FLOOR MOVEMENTS WILL NOT HARM THE FOIL MATS
CONNECT MULTIPLE COLD WIRE LEADS FROM THERMOFOIL HEATING MATS IN PARALLEL, INSIDE AN ELECTRICAL JUNCTION BOX
ENSURE THAT NO SHARP EDGES (E.G. METAL-EDGED LAMINATE LOCKING SYSTEMS) COME IN CONTACT WITH THE FOIL HEATING
USE THE FOIL TAPE PROVIDED TO BRIDGE ANY GAPS WHEN CUTTING AND TURNING THE MATS. THIS IS IMPORTANT TO KEEP THE EARTH INTACT
ENSURE ALL EARTH LEADS ARE CONNECTED TO THE EARTH RING
ENSURE THAT THE HEATERS ARE PROTECTED BY A SUITABLY RATED RCD
FAILURE TO FOLLOW THESE INSTRUCTIONS WILL INVALIDATE THE WARRANTY. PLEASE TAKE CARE TO READ THIS GUIDE THOROUGHLY
Do not touch electrics unless fully qualified
UP
E a r t h E a r t h
E a r t h
127 6 5 4 3
Protect with an RCD
PIR
Plan your installation
Follow full test procedure
Position the Conduit in the correct area
Do not cross Thermofoil PRO cable
Do not cut the cable!
Do not leave loose cable exposed
TFPIG1
WWW. WWW. WWW. WWW. WWW. WWW. If you have any questions or queries regarding this product, or any other products or servicesyou can view our complete range online, WWW.THERMOGROUPUK.COM
INSTALLATION GUIDE: THERMOFOIL PRO
5
Planning: Performing a resistance test
Planning: Thermofoil PRO™ cable formation options
! IMPORTANT SAFETY PRECAUTIONS !Planning checklist:
The section below highlights some common cable formations to tackle irregular areas too small for a Thermofoil PRO mat. If you cannot see a solution to your installation here please call our customer help line (0800 019 5899).
Cable formation: Solutions for common and irregular areas
Be sure to check the electrical resistance reading on the cable three times; before, during and after the installation process. These test symbols throughout this guide are a reminder:
Three test symbols
Test Live and Neutral, conducting the test in this way ensures total accuracy.
Resistance testWrite each resistance value on the customer handover form (P11) to ensure your customer can complete the warranty form online.
Record results
When you reach the end of a run, a simple turn can be achieved by cutting across the silverfoil (not the cable!) with scissors or a sharp blade. Turn the mat 180O and roll it out parallel to the first run.
Thermofoil PRO will not always fit the spaces around irregular shapes like a bath, toilet or sink pedestal.
In this case simply remove the cable from the mesh and arrange in loops to cover the area. Use a minimum cable spacing of 50mm and fix in place using the provided aluminium tape.
Do not place directly under permanent fixtures or furniture such as under pedistals or vanity units.
Simple turns
More simple turns....
Irregular areas
Solutions for irregular areas...
Cut the silver foil, never cut the cable!
Turn through 180O
Continue rolling out cable side down (where possible)
1
2
3
IT IS VITAL TO APPLY ALUMINIUM FIXING TAPE TO ALL LOOSE HEATING CABLES, T FOR HEAT DISTRIBUTION!
DO NOT CUT THE HEATING CABLE!TURN MAT USING SIMPLE GUIDE
FIX LOOSE CABLE USING TAPE PROVIDED
TEST CIRCUIT RESISTANCE & RECORD RESULTS - TEST A
A B C
! DO NOT CUT THE CABLE ! ! DO NOT CUT THE CABLE !
A
B
C
A
B C
Perform Test A now and record the results on p11
TFPIG1
WWW. WWW. WWW. WWW. WWW. WWW.
If you have any questions or queries regarding this product, or any other products or servicesCall our technical helpline for free on 0800 019 5899
INSTALLATION GUIDE: THERMOFOIL PRO
6
Planning: Layout
Use the grid above to plan your installation. This will help you to produce the safest, quickest and cleanest result with as little wastage as possible.
Measure your room, if you don’t already know the dimensions, and make a note of the available floor space excluding any obstacles or fixtures you might have such as sanitary ware, furniture or drainage. Use the grid to plan your installation layout making sure to include thermostat and sensor positions.
Correct spacing is essential for an efficient system. Ensure Thermofoil PRO is spaced evenly with at least 50mm gap around the perimeter of the installation.
If your floor finish manufacturer requires, you will need to allow for an edge insulation foam strip. Ask manufacturer if unsure.
Planning: Layout
! IMPORTANT SAFETY PRECAUTIONS !Planning checklist
CALCULATE AVAILABLE FLOOR SPACE
SKETCH PLAN INCLUDING ALL REQUIRED PRODUCTS
CONTACTOR/ SNUBBER IN PLACE IF REQUIRED THE ELECTRICAL SUPPLY MUST ALWAYS BE PROTECTED BY AN RCD. ENSURE THIS IS CATERED FOR BEFORE INSTALLATION!
DO NOT POSITION SENSOR & CONDUIT NEAR WATER PIPES OR TEMPERATURE INFLUENCE!
SENSOR & CONDUIT MUST BE POSITIONED INBETWEEN 2 RUNS OF HEATING CABLE!
Load calculations: Use the calculation below to work out the overall current draw for your Thermofoil PRO system. If this value is over 16A you will need to have a contactor/snubber installed by a Part P qualified electrician. Call our technical help line if you have any questions (0800 019 5899).
Example calculation:
Total Mat Wattage ÷ 230V = Amps (A)
• Thermofoil PRO• Thermostat• Sensor and Conduit• Heak Pak (If required)
Items to plan for:
TFPIG1
WWW. WWW. WWW. WWW. WWW. WWW. If you have any questions or queries regarding this product, or any other products or servicesyou can view our complete range online, WWW.THERMOGROUPUK.COM
INSTALLATION GUIDE: THERMOFOIL PRO
7
Planning: Substrate & Insulation Options
! IMPORTANT SAFETY PRECAUTIONS !Checklist:
FULLY UNDERSTAND THE DIFFERENCE BETWEEN THERMOFOIL APPLICATIONS ON TIMBER AND CONCRETE SUBSTRATES
ENSURE DESIRED FLOOR FINISH IS COMPATIBLE WITH UNDERFLOOR HEATING
ENSURE HEAT PAK IS INSTALLED AT LEAST 24 HOURS BEFORE VINYL GLUE IS USED!
PLEASE READ MANUFACTURERS SPECIFICATIONS OF FLOORING PRODUCTS USED IN CONJUNCTION WITH THERMOFOIL PRO
!
The Thermofoil mat must not be installed in direct contact with a cement or concrete slab. The heater must be installed on top of a suitable rigid insulation board.
Econoboard Insulation board may be used if additional levels of insulation are required but a soft underlay will need to be installed on top of the board.
A vapour barrier should be installed between the Thermofoil PRO mat and floor finish. This helps to eliminate any possible damage that could be caused by movement in the floating floor.
The Thermofoil mat must not be installed in direct contact with timber floor boards or chip board flooring. The heater must be installed on top of a suitable rigid insulation board.
Econoboard Insulation board may be used if additional levels of insulation are required but a soft underlay will need to be installed on top of the board.
A vapour barrier should be installed between the Thermofoil PRO mat and floor finish. This helps to eliminate any possible damage that could be caused by movement in the floating floor.
Carpet or vinyl floor finish? See page 10 for details.
Option 1: Concrete Substrate Option 2: Timber Substrate
OR
Laminate Flooring Laminate Flooring
Rigid Insulation Rigid InsulationVapour Barrier Vapour Barrier
Thermofoil PRO Thermofoil PROConcrete Substrate Timber Substrate1 1
4 42 2
3 35 5
2 2
! !
1 1
3 3
4 4
5 5
TFPIG1
WWW. WWW. WWW. WWW. WWW. WWW.
If you have any questions or queries regarding this product, or any other products or servicesCall our technical helpline for free on 0800 019 5899
INSTALLATION GUIDE: THERMOFOIL PRO
8
Make sure your substrate and insulation is clean and dust free before installing your Thermofoil PRO heating mat.
Lay Thermofoil PRO wire side up where possible. Place the Thermofoil PRO in the starting position, and roll it out ensuring the conduit position lines up in between two runs of heating cable as planned.
Feed the cold tail up and into the channel in the wall, through the cavity or pre installed conduit.
If you have not already done so now is a good time to chase a shallow channel out of the insulation or substrate to recess the cold tail into the floor slightly. This will make fitting your floor finish easier.
Step 1: Roll out the mat Step 2: Simply cut and turn the mat
Installation: Lay Thermofoil PRO mats
Allow a gap of between 50 - 100mm from the wall to the edge of the Thermofoil PRO mat.
PRO TIP
! IMPORTANT SAFETY PRECAUTIONS !Step 1 & 2 checklist:
LAY THERMOFOIL PRO WIRE SIDE UP WHERE POSSIBLE
LEAVE GAP OF 50-100MM BETWEEN MAT & WALL
FEED COLD TAIL UP WALL TO BACK BOXIF USING HEAT PAK DO NOT INSTALL SENSOR PROBE AT THIS POINT. IT MUST BE INSTALLED WITHIN THE HEAT PAK LAYER!
COVER ALL EXPOSED HEATING CABLE AND JOIN ANY CUT MATS WITH ALUMINIUM TAPE TO ENSURE EARTH CONTINUITY!
1
2
3
21
When you reach the end of a run, a simple turn can be achieved by cutting across the foil with scissors or a sharp blade, never cut the heating cable. Turn the mat 180O and roll it out parallel to the first run.
All exposed cable must be covered and cut mats must be joined for earth continuity and safety. Tape over all exposed cable and join any cut mats together using the provided aluminium fixing tape. Run an earth continuity test if unsure.
For more information on mat turns see page 5.
Tape down exposed heating cable and join mats
Cut the foil, never cut the cable!
Turn through 180O
Continue rolling out the mat cable side down
1
2
3
A
B
C
A
B C
Perform Test B now and record the results on p11
A
B
C
A
B C
TFPIG1
WWW. WWW. WWW. WWW. WWW. WWW. If you have any questions or queries regarding this product, or any other products or servicesyou can view our complete range online, WWW.THERMOGROUPUK.COM
INSTALLATION GUIDE: THERMOFOIL PRO
9
Installation: Lay flooring and connect thermostat
Make electrical connections as show in your Thermostat Installation Guide which comes in the Thermostat box.
The image above shows the correct wiring configuration for:5259 Touchscreen Programmable Thermostat5255 Chrome Touchscreen Programmable Thermostat5257 Satin Black Touchscreen Programmable Thermostat
Your thermostat may require a different wiring diagram. Please consult the relevant installation guide for full details.
You can now lay a vapour barrier and then the final floor covering. Please take care not to damage the mat in any way. If you are not instantly laying your floor finish onto Thermofoil PRO please cover with a protective material in the meantime.
Floating and laminate floors usually require an strip of expansion foam around the edge of the room. Check your floor finish manufacturer guidelines for more information.
Step 3: Lay laminate flooring Step 4: Thermostat installation
DO NOT LAY LAMINATE DIRECTLY ONTO THERMOFOIL USE A VAPOUR BARRIER LAYER!
ISOLATE ELECTRICS BEFORE DOING ANY ELECTRICAL WORKS!
! IMPORTANT SAFETY PRECAUTIONS !Step 3 & 4 checklist:
43
A
B
C
A
B C
Perform Test C now and record the results on p11
WIRE THERMOSTAT TO AN RCD
CONNECT WIRING IN ACCORDANCE WITH RELEVANT WIRING DIAGRAM
INSTALL THERMOSTAT SECURELY TO BACK BOX AND EARTH
A
B
C
A
B C
TFPIG1
WWW. WWW. WWW. WWW. WWW. WWW.
If you have any questions or queries regarding this product, or any other products or servicesCall our technical helpline for free on 0800 019 5899
INSTALLATION GUIDE: THERMOFOIL PRO
10
Step A: Heak Pak - Carpet and vinyl floors Step B: Heat Pak continued & floor finish
Installation: Carpet or vinyl flooring - Heat Pak
It is important to check that any trimming of the top board is accurate and that the adhesive coating is free from dust or fragments before removing the protective film from the baseboards. The adhesive will allow minor adjustments to be made for accurate positioning until pressure is applied.
Tapping down with a rubber mallet will ensure close contact of the adhesive coatings and produce a strong, permanent bond. Take care to position boards accurately as it is very difficult to separate them once bonded. The heating system must be switched off before installing Heat Pak. If the floor finish is to be glued to the Heat Pak , the system must not be switched back on until the glue has set completely. Temperatures should then be increased gradually.
Special attention should be made to the location of the floor sensor. A 5mm wide groove should be formed in the top board layer of the Heat Pak to take the tip of the sensor and allow the cable to run to the 50mm gap at the edge of the room. If the final floor finish is to be vinyl or similar the groove/sensor and joins should be covered with flexible filler.
You are now ready to apply your floor adhesive (if necessary) and floor finish. Please ensure you wait at least 24 hours before applying any adhesives to Heat Pak.
BA
! IMPORTANT SAFETY PRECAUTIONS !Step 8 & 9 checklist:
VAPOUR BARRIER LAID BETWEEN HEAT MAT AND FLOOR APPLICATION
LAY BASE BOARD
LAY THICKER TOP BOARD WITH STAGGERED JOINS
ALLOW 8-10MM EXPANSION GAP UNDER SKIRTING!
DO NOT LAY CARPET OR VINYL DIRECTLY ONTO THERMOFOIL USE A HEAT PAK LAYER IN BETWEEN!
Wall1
1
Top board4
Thermofoil PRO7
Skriting2 2
Base board5
Rigid insulation board8
Floor finish3
Vapour barrier6
Substrate9 9
8-10mm Expansion Gap10
10
If you are installing carpet, vinyl or another non-laminate flooring you will need Heak Pak. You will need a vapour barrier (200 microns) between Thermofoil and Heat Pak.
The Heat Pak system consists of two self-adhesive boards, baseboards and top boards, which bond to each other. Heat Pak is a floating sub-floor. It is not fixed to the floor below. Each layer is laid out with staggered joints and arranged so that the top boards overlap the joints in the baseboards. Baseboards are thinner and have a protective plastic film to keep the self-adhesive coating clean. This is laid facing upwards and the film is left in place until cutting and fitting is completed.
The top boards are thicker and have no plastic film over the adhesive coating. They are carefully positioned, adhesive side down, so that they overlap all the baseboard joints.
Floor finish
Expansion gap
3 4 5 6 7 8
TFPIG1
WWW. WWW. WWW. WWW. WWW. WWW. If you have any questions or queries regarding this product, or any other products or servicesyou can view our complete range online, WWW.THERMOGROUPUK.COM
INSTALLATION GUIDE: THERMOFOIL PRO
11
Fill out and sign the boxes below to declare that all the information recorded on this form correlates to the installation.
CONDUCTOR / CONDUCTOR CONDUCTOR / EARTHBRAID
15.7 15.3 15.9
1
0 YES / NO
YES / NO
YES / NO
YES / NO
YES / NO
YES / NO
YES / NO
YES / NO
YES / NO
YES / NO
2
3
4
5
6
7
8
9
10
1.0121402Example Room
YES / NO
THERMOFOIL PRO ON SITE RESISTANCE TEST RESULTS
Test A: After laying the Thermofoil PRO matKEY: Test B: During floor finishing Test C: On completion of floor finishing
Address:
Email:
Website:
Name:
Part P number:
Postcode:
Telephone:
Signature:
INSTALLER
Address:
Email:
Website:
Name:
Telephone:
Signature:
CUSTOMER
Postcode:
0c 0c 0c
ROOM REFERENCE
STOCKNUMBER
MAT AREA (M2)
CONNECTIONWIRE
EXTENSION B CA B CA
The Thermofoil PRO™ Under laminate Heating 15 year guarantee against manufacturers defects is a limited liability warranty and will only apply if the product is registered online. Online warranty registration must be completed within 60 days of installation to apply. Your statutory rights are not affected. In the event of a problem with your installation contact your Thermofoil PRO™ stockist. Alternatively telephone the Thermogroup advice line 0800 019 5899. Take photographs of installation at all stages of installation.
Finalise: Customer handover
Thermofoil PRO Installation Guarantee
This is the place to record the resistance test results which should be carried out when prompted during the installation process. Please fill out the entire form in clear writing to ensure your customer can register their system online or contact you with any queries that may arise after installation.
Customer handover checklist:COMPLETED ALL 3 TESTS & RECORD RESULTS
GIVEN CUSTOMER A COPY OF ORIGINAL PROOF OF PURCHASE
TAKEN PHOTOGRAPHS AT ALL STAGES OF INSTALLATION
GIVEN CUSTOMER A COMPLETED COPY OF THIS FORM
COMPLETED AND SIGNED CUSTOMER HANDOVER FORM
! IMPORTANT SAFETY PRECAUTIONS !
FAILURE TO COMPLETE THIS FORM IN FULL WILL INVALIDATE THE WARRANTY!
ENSURE YOU COMPLETE ALL 3 RESISTANCE TESTS AND ACCURATELY RECORD THE RESULTS ON THIS PAGE!
WWW.Browse our full product range, watch videos, download product literature and get a quote, all on the Thermogroup UK website.
WWW.THERMOGROUPUK.COM
CONTACT US ONLINE
WWW.0800 019 5899
CONTACT US BY PHONE
WWW.
CONTACT US BY MAIL
Thermogroup UK, Bridge House, Hop Pocket Lane, Paddock Wood, Kent. TN12 6DQ.
Got a question or query? Call our UK support line free from your land line.Open 07:30 – 16:30 Mon - Fri
Need to find us or want to write a letter to say hello? Feel free to contact us at Bridge House.
TFPIG
_A4_2
01113.P
DF
Thermogroup UK Bridge House
Hop Pocket Lane Paddock Wood
Kent TN12 6DQ
E&OE © Thermogroup UK 2012
0800 019 [email protected]
www.thermogroupuk.com
Stock No. Size (m) Output (A) Voltage (V) Resistance (Ω) Area(m2)
121402 2.0lm x 0.5m 140 230 377.9 1.00
121403 3.0lm x 0.5m 210 230 251.9 1.50
121404 4.0lm x 0.5m 280 230 188.9 2.00
121405 5.0lm x 0.5m 350 230 151.1 2.50
121406 6.0lm x 0.5m 420 230 126.0 3.00
121408 8.0lm x 0.5m 560 230 94.5 4.00
121410 10.0lm x 0.5m 700 230 75.6 5.00
121412 12.0lm x 0.5m 840 230 63.0 6.00
121416 16.0lm x 0.5m 1120 230 47.2 8.00
121420 20.0lm x 0.5m 1400 230 37.8 10.00
121424 24.0lm x 0.5m 1680 230 31.5 12.00
Thermofoil PRO
TFPIG1 INSTALLATION GUIDE: THERMOFOIL PRO