Thin-Film RF/Microwave Filters - AVX Corporationdatasheets.avx.com/lp0603.pdfThin-Film RF/Microwave Filters LP0603 Series – Test Jig Low Pass – Lead-Free Created Date 10/5/2020

The Important Information/Disclaimer is incorporated in the catalog where these specifications came from or available online at www.avx.com/disclaimer/ by reference and should be reviewed in full before placing any order. 113

GENERAL DESCRIPTIONThe LP0603 ITF (Integrated Thin Film) Lead-Free LGA Low Pass Filter is based on thin-film multilayer technology. The technology provides a miniature part with excellent high frequency performance and rugged construction for reliable automatic assembly.The ITF Low Pass Filters are offered in a variety of frequency bands compatible with various types of high frequency wireless systems.

FEATURES• Miniature Size: 0603• Frequency Range: 900MHz-5.5HGz• Characteristic Impedance: 50 Ohm• Operating/Storage Temperature: -40°C to +85°C• Power Rating: 3W Continuous• Low Profile• Rugged Construction• Lead Free• Taped and Reeled

APPLICATIONS• Mobile communications• Satellite TV receivers• GPS• Vehicle location systems• Wireless LANs• RFID

LAND GRID ARRAY ADVANTAGES• Inherent Low Profile• Self Alignment during Reflow• Excellent Solderability• Low Parasitics• Better Heat Dissipation

HOW TO ORDERLP

Style

0603

Size0603

XXXX

FrequencyMHz

A

TypeA or N

A

Sub-Type

N

TerminationLGA

**Ni/Lead Free Solder

TR

Taped & Reeled

LEAD-FREE COMPATIBLECOMPONENT

FINAL QUALITY INSPECTIONFinished parts are 100% tested for electrical parameters and visual characteristics. Each production lot is evaluated on a sample basis for:

• Static Humidity: 85°C, 85% RH, 160 hours• Endurance: 125°C, IR, 4 hours

TERMINATIONNickel/Lead-Free Solder coating compatible with automatic soldering technologies: reflow, wave soldering, vapor phase and manual.

**RoHS compliant

081320

Thin-Film RF/Microwave Filters

LP0603 Series – LGA TerminationLow Pass – Harmonic Lead-Free

http://www.avx.com/resources/catalogs/datasheet-catalog-disclaimer/

The Important Information/Disclaimer is incorporated in the catalog where these specifications came from or available online at www.avx.com/disclaimer/ by reference and should be reviewed in full before placing any order.114

DIMENSIONS: millimeters (inches)(Bottom View)

L

T

S

W

B

A

TERMINALS AND ORIENTATION IN TAPE (TOP VIEW)

OUT GND

GNDIN

OUT GND

GNDIN

RECOMMENDED PAD LAYOUT (MM)

ELECTRICAL CHARACTERISTICS(Guaranteed over –40°C to +85°C Operating Temperature Range)

L 1.6±0.1 (0.063±0.004)

W 0.84±0.1 (0.033±0.004)

T 0.60±0.1 (0.024±0.004)

A 0.25±0.05 (0.010±0.002)

B 0.20±0.05 (0.008±0.002)

S 0.05±0.05 (0.002±0.002)

NOTE: Additional Frequencies Available Upon Request

P/N Frequency Band [MHz]I. Loss

[dB]

VSWR max [dB]

Attentuation typ. [dB]

LP0603A0902ANTR 890-915 0.35 typ (0.5 max) 1.425 @ 2xF0 14 @ 3xF0








LP0603N3500ANTR 3400-3600 -0.3 typ. -0.5 max. 1.430 @ 2xF0 20 @ 3xF0



012419


LP0603 Series – LGA TerminationLow Pass – Lead-Free



LP0603A0902ANTR

LP0603A1747ANTR

LP0603A1880ANTR

LP0603A1842ANTR

LP0603A1950ANTR

LP0603A0947ANTR

-50

-38

-25

-13

0

0 0.25 0.50 0.75 1.00 1.25 1.50 1.75 2.00 2.25 2.50 2.75 3.00 3.25 3.50 3.75 4.00

S21S11(dB)

Frequency (GHz)

F0

2F0

3F0

-50

-38

-25

-13

0

0 0.25 0.50 0.75 1.00 1.25 1.50 1.75 2.00 2.25 2.50 2.75 3.00 3.25 3.50 3.75 4.00

S21S11(dB)

Frequency (GHz)

2F0

3F0

F0

-50

-38

-25

-13

0

0 0.50 1.00 1.50 2.00 2.50 3.00 3.50 4.00 4.50 5.00 5.50 6.00 6.50 7.00 7.50 8.00 8.50 9.00

S21S11(dB)

Frequency (GHz)

2F0

F0

3F0

-50

-38

-25

-13

0

0 0.50 1.00 1.50 2.00 2.50 3.00 3.50 4.00 4.50 5.00 5.50 6.00 6.50 7.00 7.50 8.00

S21S11(dB)

Frequency (GHz)

2F0

F0

3F0

-50

-45

-40

-35

-30

-25

-20

-15

-10

-5

0

0 0.50 1.00 1.50 2.00 2.50 3.00 3.50 4.00 4.50 5.00 5.50 6.00 6.50 7.00 7.50 8.00

S21S11(dB)

Frequency (GHz)

2F0

F0

3F0

-50

-38

-25

-13

0

0 0.50 1.00 1.50 2.00 2.50 3.00 3.50 4.00 4.50 5.00 5.50 6.00 6.50 7.00 7.50 8.00

S21S11(dB)

Frequency (GHz)

2F0

F0

3F0

012419




The Important Information/Disclaimer is incorporated in the catalog where these specifications came from or available online at www.avx.com/disclaimer/ by reference and should be reviewed in full before placing any order.116

LP0603A2140ANTR

LP0603N3500ANTR

LP0603A2442ANTR

LP0603N5200ANTR

LP0603N5500ANTR

-50

-45

-40

-35

-30

-25

-20

-15

-10

-5

0

0 0.50 1.00 1.50 2.00 2.50 3.00 3.50 4.00 4.50 5.00 5.50 6.00 6.50 7.00 7.50 8.00

S21S11(dB)

Frequency (GHz)

2F0

F0

3F0

-50

-45

-40

-35

-30

-25

-20

-15

-10

-5

0

0 0.50 1.00 1.50 2.00 2.50 3.00 3.50 4.00 4.50 5.00 5.50 6.00 6.50 7.00 7.50 8.00 8.50 9.00 9.50 10.00

S21S11(dB)

Frequency (GHz)

2F0

F0

3F0

-50

-45

-40

-35

-30

-25

-20

-15

-10

-5

0

0 1 2 3 4 5 6 7 8 9 10 11 12 13

S21S11(dB)

Frequency (GHz)

2F0

F0

3F0

0 1 2 3 4 5 6 7 8 9 10 11 12 13-50

-45

-40

-35

-30

-25

-20

-15

-10

-5

0

S21S11(dB)

Frequency (GHz)

2F0

F0

0 1 2 3 4 5 6 7 8 9 10 11 12 13-50

-45

-40

-35

-30

-25

-20

-15

-10

-5

0

S21S11(dB)

Frequency (GHz)

2F0

F0

012419





TEST JIG FOR LP0603 LEAD-FREE LGA LOW PASS FILTER

GENERAL DESCRIPTIONThese jigs are designed for testing the LP0603 LGA Low Pass Filters using a Vector Network Analyzer.They consist of a dielectric substrate, having 50Ω microstrips as conducting lines and a bottom ground plane located at a distance of 0.127mm from the microstrips.The substrate used is Neltec’s NH9338ST0127C1BC (or similar).The connectors are SMA type (female), ‘Johnson Components Inc.’ Product P/N: 142-0701-841 (or similar).Both a measurement jig and a calibration jig are provided.The calibration jig is designed for a full 2-port calibration, and consists of an open line, short line and through line. LOAD calibration can be done by a 50Ω SMA termination.

MEASUREMENT PROCEDUREFollow the VNA’s instruction manual and use the calibration jig to perform a full 2-Port calibration in the required bandwidths.

Solder the filter to the measurement jig as follows:

Input(Filter)

ç Connector 1 (Jig) GND (Filter) ç GND (Jig)

Output(Filter)

ç Connector 2 (Jig) GND (Filter) ç GND (Jig)

Set the VNA to the relevant frequency band. Connect the VNA using a 10dB attenuator on the jig terminal connected to port 2 (using an RF cable).

Measurement Calibration Jig

Connector 1

Connector 2 Load &Through

Short line toGND

ConnectorJohnsonP/N 152-0701-841

Openline

Load &OUT

012419


LP0603 Series – Test JigLow Pass – Lead-Free


Thin-Film RF/Microwave Capacitor TechnologyAccu-P® SeriesThin-Film TechnologyThin-Film Chip CapacitorsSingle and Power Type Capacitors0201 Typical Electrical Tables0402 Typical Electrical Tables0603 Typical Electrical Tables0805 Typical Electrical Tables1210 Typical Electrical TablesHigh Frequency CharacteristicsEnvironmental / Mechanical CharacteristicsPerformance Characteristics RF Power ApplicationsApplication NotesUltra-Miniature 01005 Size

Thin-Film RF/Microwave Inductor TechnologyAccu-L® SeriesL0201 Tight Tolerance RF InductorL0402 Tight Tolerance RF InductorHigh-Q RF Inductor - L0402 & L0805L0603 AND L0805 SMD High-Q RF Inductor – Accu-L®Environmental CharacteristicsApplication NotesThin-Film RF/Microwave ProductsDesigner Kits

Thin-Film RF/Microwave Directional CouplersCP0302/CP0402/CP0603/CP0805 and DB0603N/DB0805 3dB 90°CP0402W2700FNTR Wide Band High DirectivityCP0402W2700FNTR Test JigsHigh Directivity Directional Couplers For WiFi BandsCP0402P High Directivity, Tight Coupling ToleranceCP0402 High Directivity LGA TerminationCP0603 High Directivity LGA TypeCP0402 / CP0603 High Directivity Couplers Test JigsLGA Couplers Design KitsCP0603 SMD TypeCP0603 SMD Type – High DirectivityCP0805 SMD TypeCP0805 Layout TypesCP0805 and CP0603 Test JigDB0603N 3dB 90° CouplersDB0805 3dB 90° Couplers

Thin-Film RF/Microwave FiltersLow Pass – Harmonic Lead-FreeLP0402N Series – LGA TerminationLP0402N Series – Test JigLP0603 Series – LGA TerminationLP0603 Series – Test JigLP0805 Series – SMD TerminationLP0805 Series – Test JigLow Pass 0805 High Performance SMD 8WLP0805H0700ASTR – SMD TerminationLP0805H0750ASTR – SMD TerminationLP0805H0780ASTR – SMD TerminationLP0805H0942ASTR – SMD TerminationLP0805H1000ASTR – SMD TerminationLP0805H1250ASTR – SMD TerminationLP0805H1800ASTR – SMD TerminationLP0805H1900ASTR – SMD TerminationLP0805H2400ASTR – SMD TerminationLP0805H2900ASTR – SMD TerminationLP0805H3500ASTR – SMD TerminationLP0805H4000ASTR – SMD Termination1206 High Performance Low Pass 12WLP1206A0512BNTR – LGA TerminationLP1206A0600ANTR – LGA TerminationLP1206A0700ANTR – LGA TerminationLP1206A0720ANTR – LGA TerminationLP1206A6000ANTR – LGA Termination1206 High Performance Low Pass 8WLP1206A0700ASTR – SMD TerminationLP1206A0860ASTR – SMD TerminationLP1206A1000ASTR – SMD TerminationLP1206A1500ASTR – SMD TerminationLP1206A2000ASTR – SMD TerminationLP1206A2500ASTR – SMD TerminationLP1206A3200ASTR – SMD TerminationLP1206A3500ASTR – SMD TerminationLP1206A3600ASTR – SMD TerminationLP1206A3800ASTR – SMD Termination2816 High Performance Low Pass 15W LP2816A0512SNTR – LGA TerminationLP2816A0680SNTR – LGA TerminationLP2816A1300SNTR – LGA TerminationLP2816A1400SNTR – LGA TerminationLP2816A1600SNTR – LGA TerminationLP2816A1700SNTR – LGA TerminationLP2816A1800SNTR – LGA TerminationLP2816A1900SNTR – LGA TerminationLP2816A2500SNTR – LGA TerminationBP0805 Band Pass Filter SMD 5WBP0805A1308ASTRBP0805A1457ASTRBP0805A1795ASTRBP0805A2160ASTRBP0805A3500ASTRBP0805A3600ASTRBP0805A3700ASTRBP0805B4050ASTRBP0805A4320ASTRBP1206 Band Pass Filter SMD 8WBP1206A0802ASTRBP1206A0879ASTRBP1206A2880ASTRBP1206A6670ASTR

Multilayer Organic (MLO®) FiltersMLO® High Pass FiltersGeneral InformationElectrical Specifications

MLO® Low Pass FiltersGeneral InformationElectrical Specifications

MLO® Band Pass FiltersGeneral InformationElectrical Specifications

Mechanical Specifications, Pad Layout, and Mounting RecommendationsFootprint AFootprint BFootprint CFootprint DFootprint EFootprint E1Footprint E2Footprint F

Multilayer Organic (MLO®) CapacitorsGeneral InformationMechanical & Environmental Specifications

Multilayer Organic (MLO®) Diplexers0603 WLAN/BT0805 CDMA0805 WCDMA0805 WLAN0805 WLAN/BTAutomated SMT Assembly/SMT Reflow Profile

Multilayer Organic (MLO®) InductorsTight ToleranceHigh CurrentHi-QPerformance CharacteristicsAutomated SMT Assembly/SMT Reflow Profile

Multilayer Organic (MLO®) SMT CrossoversRF-DCRF-RFAutomated SMT Assembly/SMT Reflow Profile

RF/Microwave InductorsAL Series – Air Core InductorsAS Series – Square Air Core InductorsLCWC Series – Wire Wound Chip InductorLCCI Series – Multi-Layer Ceramic Chip Inductors

RF/Microwave CapacitorsRF/Microwave Multilayer Capacitors (MLC)UQ Series High Q Ultra Low ESR MLC700A Series NP0 Porcelain and Ceramic Multilayer Capacitors200A Series Ultra Low ESR MLC

RF/Microwave CapacitorsRF/Microwave Multilayer Capacitors (MLC)SQ Series High Ultra Low ESR MLC

RF/Microwave CapacitorsRF/Microwave CapacitorsAQ SeriesCDR Series — MIL-PRF-55681 (RF/Microwave Chips)Performance CurvesAutomatic Insertion PackagingHQ Series, High RF Power CapacitorsRF/Microwave C0G (NP0) CapacitorsUltra Low ESR “CU” Series, C0G (NP0) Capacitors (RoHS)Ultra Low ESR “U” Series, C0G (NP0) Capacitors (RoHS)Ultra Low ESR “U” Series, C0G (NP0) Capacitors (Sn/Pb)Ultra Low ESR “U” Series, C0G (NP0) Capacitors (RoHS) Automotive, AEC Q200 QualifiedRF/Microwave “U” Series Designer Kits

Documents

Thin-Film RF/Microwave Filters - AVX Corporationdatasheets.avx.com/lp0603.pdfThin-Film RF/Microwave Filters LP0603 Series – Test Jig Low Pass – Lead-Free Created Date 10/5/2020