Timekeeping Indicators Measuring Lap Times …...it on your phone. B Configure Bluetooth settings. Enable the phone’s Bluetooth. Note For details about setting procedures, see your

Contents

Before Getting Started...Indicators

Cycling Between Timekeeping Mode DigitalDisplay Contents

Navigating Between Modes

Shifting the Hands

Connecting with a Phone

Using Mobile Link with a MobilePhone

ConnectionConnecting with a PhoneCanceling a Connection with a PhoneUsing the Watch in a Medical Facility orAircraftUnpairingIf you purchase another phone

Auto Time Adjustment

Viewing Pedometer Data

Viewing Stopwatch Data

Configuring Stopwatch Target Time Settings

Configuring Programmable Timer Settings

Configuring World Time Settings

Adjusting Hand Alignment

Phone Finder

Configuring Watch Settings

Changing the Home City Summer Time Setting

PedometerCounting Steps

Checking Today’s Step Count

Resetting Today’s Step Count

Specifying a Daily Step Target

Step Reminder

Clearing a Step Reminder Alert Indicator

Enabling/Disabling Step Reminder

Causes of Incorrect Step Count

MA1810-EB © 2018 CASIO COMPUTER CO., LTD.

StopwatchSplit Times and Lap Times

Measuring Elapsed Time

Measuring a Split Time

Measuring Lap Times

Using the Target Time AlarmOverviewSpecifying a Target TimeMeasuring Elapsed Time with the TargetTime FunctionClearing a Specific Target TimeClearing All Target Times

Managing Data RecordsViewing Lap/Split RecordsDeleting a Particular RecordDeleting All Records

TimerSetting a Timer Start Time

Using the Timer

Measuring Elapsed Time with Auto Start

Using the Programmable Timer as an IntervalTimer

OverviewConfiguring Settings for an Interval TimerUsing an Interval Timer

Dual TimeConfiguring Dual Time Settings

Swapping the Home City Time and Dual Time

Alarms and Hourly Time SignalConfiguring Alarm Settings

Enabling/Disabling an Alarm or the HourlyTime Signal

Stopping an Alarm

Determining an Alarm’s On/Off Status

Adjusting the Time SettingManually

Setting the Time and Date

Switching Between 12-hour and 24-hourTimekeeping

Illumination LightIlluminating the Face Manually

Auto Light

Configuring the Auto Light Setting

Specifying the Illumination Duration

Hand Alignment AdjustmentAdjusting Hand Alignment

Battery Replacement

Other SettingsEnabling the Button Operation Tone

Moving to Another Time Zone

Other InformationSupported Phones

Specifications

Mobile Link Precautions

Copyrights and Registered Copyrights

Troubleshooting

Operation Guide 5556

1

Before GettingStarted...

This section provides an overview of yourwatch and explains how to connect with aphone. Connecting with a phone makes itpossible to synchronize the watch’s timesetting with information acquired from thephone, and to view the step count of the watchand its stopwatch data on the phone screen.

Note

● The illustrations included in thisoperation guide have been created tofacilitate explanation. An illustrationmay differ somewhat from the item itrepresents.

Indicators

⑤④

⑥⑦

②①

⑪⑫⑬⑭

⑧ ⑨⑩

③

⑮⑯

A Graphic areaIndicates how much of your daily step targetyou have attained.

B Step indicatorsIndicate whether or not the step count is beingincremented.

C [SPL]Displayed while a split time is displayed.

D [LAP]Displayed while a lap time is displayed.

E [P]Appears when the displayed time is a p.m.time.

F [LT]Displayed while Auto Light is enabled.

G eDisplayed while there is connection betweenthe watch and a phone.

H [REC]Displayed while the watch is in the RecallMode.

I [TGT]In the Stopwatch Mode, indicates themeasurement status while the Target Timefunction is enabled.

J [HND]Displayed while the watch’s hands are shiftedfor easier reading.

K [STEPS]Displayed while the step count is displayed.

L

Flashes if you have not walked for a specifiedamount of time (Step Reminder).

M AlarmDisplayed while an alarm is turned on.

N Hourly time signalDisplayed while the hourly time signal isenabled.

O

Flashes when you attain your daily step target.

P [DST]Displayed while the current time is a summertime (DST).

Cycling BetweenTimekeeping Mode DigitalDisplay Contents

B

BB

B

Month, day, second, day of the week

Hour, minute, second, day of the weekSeconds

Step count

To cycle between digital display contentswhile in the Timekeeping Mode, press (B).

Navigating Between ModesPress (C) to cycle between modes.● In any mode, hold down (C) for at least two

seconds to enter the Timekeeping Mode.

CC

CC

CC

Stopwatch Mode

Timer Mode

Alarm Mode

Timekeeping Mode

Dual Time Mode Recall Mode

● Connecting with a PhoneIn the Timekeeping Mode, hold down (D) forat least two seconds. Release the button whene and start to flash, which indicates that thewatch is connected with the phone.● To terminate a connection between a phone

and the watch, press any watch buttonbesides (L).

D

Any button besides (L)

After connectionBefore connection


2

Shifting the HandsHand shift moves the hands out of the way foreasy viewing of display information.

1. While holding down (L), press (C).● This will shift the analog hands to allow

easy viewing of display information.

2. To return the hands to their normalpositions, hold down (L) as you press (C)again.

Note

● Changing to another mode while thehands are shifted will cause them toreturn to their normal timekeepingpositions.

Connecting with a PhoneTo connect the watch with a phone, first installthe CASIO “BABY-G Connected” app on thephone and then use Bluetooth to pair thewatch with the phone.

●A Install the app on your phone.In Google Play or the App Store, search for theCASIO “BABY-G Connected” app and installit on your phone.

●B Configure Bluetooth settings.Enable the phone’s Bluetooth.

Note

● For details about setting procedures,see your phone documentation.

●C Pair the watch with a phone.Before you can use the watch in combinationwith a phone, you first need to pair them.

1. Enter the Timekeeping Mode.l Navigating Between Modes

2. Move the phone to be paired with close to(within one meter of) the watch.

3. On the phone’s Home Screen, tap the“BABY-G Connected” icon.

4. Follow the instructions on the phone’sscreen to pair with the watch.● If a pairing prompt message appears,

perform the operation shown on thephone screen.

● If pairing fails for some reason, performthe procedure again from step 1.

Pairing complete.Pairing started.

Using Mobile Link witha Mobile Phone

While there is a Bluetooth connectionbetween the watch and phone, the watch timesetting is adjusted automatically. You can alsochange the watch’s other settings.

Important!

● The watch cannot connect with aphone while a stopwatchmeasurement or timer countdownoperation is in progress.

Note

● This function is available only whileBABY-G Connected is running on thephone.

● This section describes watch andphone operations.X : Watch operationY : Phone operation

Connection

Connecting with a PhoneThis section explains how to establish aBluetooth connection with a phone that ispaired with the watch.● If the watch is not paired with the phone you

want to connect with, refer to the informationbelow and pair them.lC Pair the watch with a phone.

1. X Enter the Timekeeping Mode.l Navigating Between Modes

2. Move the phone close to (within one meterof) the watch.

3. X If e is not displayed, hold down (D) for atleast two seconds. Release the buttonwhen e and start flashing.When a connection is establishedbetween the watch and phone, e will stopflashing.

Trying to connect Connection successful

Important!

● If you have problems establishing aconnection, it could mean that BABY-G Connected is not running on thephone. On the phone’s home screen,tap the “BABY-G Connected” icon.After the app starts up, hold down thewatch’s (D) button for at least twoseconds.

Note

● The connection will be terminated ifyou do not perform any operation onthe watch or phone for a fixed amountof time.To specify the connection limit time,perform the following operation withBABY-G Connected: “Watchsettings”n“Connection time”. Next,select a setting of 3 minutes, 5 minutes,or 10 minutes.


3

Canceling a Connection with aPhone

To terminate a Bluetooth connection, pressany watch button besides (L).

DisconnectedConnected

Using the Watch in a Medical Facilityor Aircraft

Whenever you are in a hospital, on an aircraft,or in any other location where connection witha phone may cause problems, you canperform the procedure below to disable autotime adjustment. To re-enable auto timeadjustment, perform the same operationagain.

1. Y Tap the “BABY-G Connected” icon.2. X Hold down (D) for at least two seconds.

Release the button when e and start toflash.When a connection is establishedbetween the watch and phone, e will stopflashing.


3. Y Perform the operation shown on thephone screen to enable or disable autotime adjustment.

Unpairing

1. X If the watch is connected with a phone,press any button besides (L) to terminatethe connection.


2. Y Tap the “BABY-G Connected” icon.3. Y Perform the operation shown on the

phone screen to unpair.

If you purchase another phoneYou need to perform the pairing operationwhenever you want to establish a Bluetoothconnection with a phone for the first time.lC Pair the watch with a phone.

Auto Time AdjustmentYour watch will connect with a phone at presettimes each day and adjust its time settingsautomatically.● Using Auto AdjustYour watch adjusts its time setting four timesa day according to a preset schedule. Itperforms the adjustment operationautomatically as you go about your daily life,without any operation required by you.

12:30

Important!

● The watch may not be able to performauto time adjustment under theconditions described below.ーWhile the watch is too far away from

its paired phoneーWhile communication is not possible

due to radio interference, etc.ーWhile the phone is updating its

systemーWhile BABY-G Connected is not

running on the phone

Note

● If the watch does not indicate thecorrect time even if it is able to connectwith a phone, adjust the hand and dayindicator positions.l Adjusting Hand Alignment

● If there is a World Time City specifiedwith BABY-G Connected, its time willalso be adjusted automatically.

● The watch will connect with the phoneand perform auto time adjustment ataround 12:30 a.m., 6:30 a.m., 12:30p.m. and 6:30 p.m. The connection isautomatically terminated after autotime adjustment is complete.

● Triggering Immediate Time AdjustmentThe watch’s time setting will be adjustedautomatically whenever you establish aconnection between the watch and a phone.Whenever you want to adjust the watch’s timesetting based on your phone's time, performthe procedure below to connect with a phone.

1. X Press (D).This causes e and to flash on thedisplay. e will stop flashing when aconnection is established between thewatch and phone, and the watch’s timesetting will be synchronized with that ofthe phone.

Trying to connect Following time correction

Note

● The connection is terminatedautomatically after time adjustment iscomplete.

● If time adjustment fails for somereason, the watch will return to theTimekeeping Mode without changingits time setting.


4

Viewing Pedometer DataBABY-G Connected can be used to view thedata below, which is measured by the watch.● 24-hour step count, exercise intensity, and

physical exertion● Whether or not there is a stopwatch

measurement or timer measurement(24 hours of data displayed by dividing it into30-minute segments.)

● Weekly number of steps, calories burned




3. Y Follow the instructions on the screen todisplay pedometer data.

Note

● You can also use BABY-G Connectedto specify a daily step target.

● Though the step count is displayed onthe watch in real time, BABY-GConnected displays step counts at thetop of each hour and every half hour.Because of this the step countsdisplayed by BABY-G Connected maybe different from those displayed bythe watch.

Viewing Stopwatch DataThis section explains how to send lap timesand split times (up to 200 records) stored inwatch memory, and other data to your phonefor viewing with BABY-G Connected.

● Sending Stopwatch Data to a PhoneUse the procedure below to send data fromthe watch to a phone.




3. Y Perform the operation shown on thephone screen to transfer data measuredby the watch to the phone.After data transfer is complete, a list of themeasurement data will appear on thephone display.● Tapping a stopwatch data item displays

its details.

● Checking Sent DataUse BABY-G Connected to check the datayou sent to the phone.

1. Y Tap the “BABY-G Connected” icon.2. Y Perform the operation shown on the

phone screen to view the measurementdata you want.

Note

● You can delete data by tapping “Edit”.

Configuring StopwatchTarget Time Settings

You can use BABY-G Connected to configuresettings for up to 10 target times. Target timescan be set in one-second units, for a total ofup to 24 hours.● For information about target times, refer to

the information below.l Overview




3. Y Perform the operation shown on thephone screen to configure stopwatchtarget time settings.


5

Configuring ProgrammableTimer Settings

You can use BABY-G Connected to configureprogrammable timer settings and create agroup of multiple timers.● For information about the programmable

timer, refer to the information below.l Overview




3. Y Perform the operation shown on thescreen to configure the programmabletimer settings.

Note

● To change a timer title or delete a timer,tap “Edit”.

Configuring World TimeSettings

Specifying a World Time City with BABY-GConnected causes the watch’s World TimeCity to change accordingly. The standardtime/summer time setting of the World Timewill be adjusted automatically without anywatch operation required by you.

Note

● BABY-G Connected World Time letsyou select from among approximately300 cities as the World Time City.

● You can use BABY-G Connected toconfigure settings for user cities thatare not included in the watch’s built-inWorld Time Cities. You can then useBABY-G Connected to select a usercity as your World Time City.

● Selecting a World Time City




3. Y Perform the operation shown on thephone screen. The World Time setting willbe reflected on the watch.● You can check the World Time by

entering the Dual Time Mode.

● Configuring the Summer Time Setting




3. Y Perform the operation shown on thephone screen to select a summer timesetting.● “Auto”

The watch switches between standardtime and summer time automatically.

● “OFF”The watch always indicates standardtime.

● “ON”The watch always indicates summertime.

Note

● While the summer time setting is“Auto”, the watch will switch betweenstandard time and summer timeautomatically. You do not need toswitch between standard time andsummer time manually. Even if you arein an area that does not observesummer time, you can leave thewatch’s summer time setting as “Auto”.

● Changing the time setting manuallywith a watch operation will cancel autostandard time/summer time switching.

● BABY-G Connected screen showsinformation about summer timeperiods.


6

● Swapping Your World Time and HomeTime




3. Y Perform the operation shown on thephone screen to swap your Home Timewith your World Time.For example, if your Home City is Tokyoand the World Time City is New York, theywill be swapped as shown below.

After swappingBefore swapping

World Time City (New York)

World Time City (Tokyo)

Home City (New York)Home City (Tokyo)

Note

● Auto time adjustment does not work for24 hours after swapping of the HomeTime and World Time.

Adjusting Hand AlignmentIf the hands are out of alignment even thoughauto time adjustment is being performed, useBABY-G Connected to adjust them.




3. Y Perform the operation shown on thephone screen to correct hand alignment.

Phone FinderYou can use phone finder to trigger a tone onthe phone to make it easy to find. The tone isforced to sound even if the phone is in vibratemode.

Important!

● Do not use this function in areas wherephone call tones are restricted.

● The tone sounds at a high volume. Donot use this function when listening tophone output over earphones.

1. X If the watch is connected with a phone,press any button besides (L) to terminatethe connection.


2. X Hold down (C) for at least two seconds.This will cause the watch to enter theTimekeeping Mode.

3. X Hold down (D) for at least five seconds.Release the button when [Find] appears.A connection will be established betweenthe watch and phone, and then thephone’s ringtone will sound.● It will take a few seconds before the

phone tone sounds.

4. X Press any button besides (L) to stop thetone.● You can press any watch button to stop

the phone tone only during the first 30seconds after it starts to sound.

Configuring Watch SettingsYou can use BABY-G Connected to specifythe amount of time until the Bluetoothconnection is automatically terminated andthe illumination duration, and to configureother settings.




3. Y Select the setting you want to changeand then perform the operation shown onthe phone screen.


7

Changing the Home CitySummer Time Setting




3. Y Perform the operation shown on thephone screen to change your Home Citysummer time setting.

PedometerYou can use the pedometer to keep track ofyour step count while walking, engaging inyour normal daily activities, etc.

● Daily Step Target Attainment Alert flashes to let you know when you attain your

daily step target.

● Step ReminderStudies suggest that sitting too much is badfor the health.Step Reminder displays an indicator andsounds an alert when it determines you havenot walked enough during a specific period.This is valuable feedback that helps achieveyour exercise goals.If the watch performs a Step Reminder alertoperation, get up and walk for about fiveminutes to clear it.

Counting StepsIf you are wearing the watch correctly, thepedometer will count your steps as you walkor engage in your normal daily activities.

Important!

● Since this watch’s pedometer is awrist-worn device, it may detect non-step movements and count them assteps. Also, abnormal arm movementswhile walking may cause a miss countof steps.

● Getting ReadyTo enable the most accurate step count, wearthe watch with the face on the outside of yourwrist and tighten the band securely. A looseband may make it impossible to obtain correctmeasurement.

NOYES

● Counting StepsThe pedometer will start counting your stepswhen you start walking. About 10 secondsafter you start walking, the step indicatorsappear to indicate that your steps are beingcounted.Alternating at one-second intervals: Walking(step count being incremented)Both displayed: Not walking (step count notbeing incremented)

Step indicators

● Checking Your Progress to Your DailyStep Target

The graphic display area shows your currentprogress toward achieving the daily steptarget specified by you.Also, flashes when you attain your dailystep target.Example: Daily target of 10,000 steps

0 steps

1,000 steps

5,000 steps

10,000 steps (goal attained)


8

Checking Today’s StepCount


2. Use (B) to display the step count.

B

BB

B

Month, day, second, day of the week

Hour, minute, second, day of the weekSeconds

Step count

Step count graphDaily step count

● Interpreting the Step Count GraphThe Step Count Graph shows the number ofsteps (up to 1,000) you have taken each hour.This lets you easily check your walking paceover the past 10 or 11 hours.● The Step Count Graph is not displayed

while the step count is zero.● Graph contents are normally updated at the

top of each hour.

1101‒ 250

251‒ 500501‒ 750751‒10001001‒ Current

Time

Step count

Note

● The step count can show a value up to999,999 steps. If the step countexceeds 999,999, the maximum value(999,999) remains on the display.

● The step count is not displayed duringthe first 10 seconds of a walk in orderto avoid miscounting of non-walkingmovements. After you have beenwalking for about 10 seconds, thecount appears, including the steps youtook during the previous 10 seconds.

● The step count is reset to zero atmidnight each day.

● To save power, step counting stopsautomatically if you take off the watch(no detectable watch movement) andyou do not perform any operation fortwo or three minutes.

● They are also updated when any oneof the events below occurs.ーWhen accelerometer operation is

stopped to save powerーWhen counting is not possible due to

accelerometer error or insufficientpower

Resetting Today’s StepCount


2. Hold down (B) and (D) at the same timefor at least two seconds. Release thebuttons when [CLR] stops flashing.This resets the step count.

Specifying a Daily StepTarget

You can specify a daily step goal within therange of 1,000 to 50,000, in units of 1,000steps.


2. Hold down (A) for at least two seconds.Release the button when the StepReminder settings screen ([OFF] or [ON]flashing) appears.

3. Press (C).● This causes the current daily step target

to flash.

Daily step target

4. Use (D) and (B) to change the daily steptarget setting.

5. Press (A) to exit the setting screen.

Step ReminderIf the watch determines that you have notwalked for a preset amount of time, it willsound a tone and display a Step Reminderindicator. If the watch performs this StepReminder alert operation, get up and walk forfive minutes to clear it.

Step Reminder


9

Clearing a Step ReminderAlert Indicator will disappear from the display after you

reach a preset step count.

Step Reminder

Note

● Measurement stops, the watch entersa power saving state, and disappears from the display if you havethe watch removed from your wrist (nodetectable watch movement) and youdo not perform any operation for two orthree minutes. However, if you performsome watch operation within one hourafter it enters power saving, it will exitpower saving and will start flashingagain.

Enabling/Disabling StepReminder


2. Hold down (A) for at least two seconds.Release the button when the StepReminder setting screen ([OFF] or [ON]flashing) appears.

3. Press (D) to toggle Step Reminderbetween enabled and disabled.[ON]: Enabled[OFF]: Disabled


Causes of Incorrect StepCount

Any of the conditions below may make propercounting impossible.● Walking while wearing slippers, sandals, or

other footwear that encourages a shufflinggait

● Walking on tile, carpeting snow, or othersurface that causes a shuffling gait

● Irregular walking (in a crowded location, ina line where walking stops and starts atshort intervals, etc.)

● Extremely slow walking or extremely fastrunning

● Pushing a shopping cart or baby stroller● In a location where there is a lot of vibration,

or riding on a bicycle or in a vehicle● Frequent movement of the hand or arm

(clapping, fanning movement, etc.)● Walking while holding hands, walking with

a cane or stick, or engaging in any othermovement in which your hand and legmovements are not coordinated with eachother

● Normal daily non-walking activities(cleaning, etc.)

● Wearing the watch on your dominant hand● Walking for 10 seconds or less● Watch hand movement (by the hand shift

function, etc.)

StopwatchThe stopwatch measures elapsed time in1/100-second units for the first hour, and in 1-second units after that for up to 24 hours.In addition to normal elapsed timemeasurements, the stopwatch also lets youtake split time and lap time readings. You canalso set a target time and monitor yourprogress in attaining it. You can configuresettings so the watch alerts you with a beeperand/or display indicator when you attain yourtarget.

Note

● Up to 200 split time and lap timerecords can be stored in watchmemory. Perform a lap or split timeoperation while there are already 200records in memory will cause theoldest record to be deletedautomatically to make room for the newone.

● You can use the Recall Mode to viewthe latest measurement data.l Viewing Lap/Split Records

● You can use BABY-G Connected toview past measurement data.

Getting ReadyEnter the Stopwatch Mode.l Navigating Between Modes

Split Times and Lap Times● Split timeA split time is the time elapsed from the start,up to any point along the course of an event.

D

B

B

D Goal

Split 3

Split 2

Split 1

Start


10

● Lap timeA lap time shows the time elapsed during aspecific lap around a track, etc.

D

B

B

D Goal

Lap 3

Lap 2

Lap 1

Start

Measuring Elapsed Time

1. Use the operations below to measureelapsed time.

D

D

D

D Stop

Resume

Stop

Start

● Elapsed time is shown in 1/100-secondunits for the first hour of themeasurement. After the first hour,elapsed time is shown in one-secondunits.

Stopwatch number

Stopwatch number

After first hourFirst hour

1/100 seconds

SecondsSecondsHours MinutesMinutes

2. Press (B) to reset the elapsed time to allzeros.

Measuring a Split Time

1. Press (A) to display [SPL].

2. Use the operations below to measureelapsed time.● Each press of (B) causes the elapsed

time up to that point (split time) to beindicated for eight seconds.

D

B

D Stop

Split

Start


Stopwatch number

Stopwatch number


1/100 seconds



Measuring Lap Times

1. Press (A) to display [LAP].

2. Use the operations below to measureelapsed time.● Each press of (B) causes the elapsed

time of the section (lap time) to beshown for eight seconds.

D

B

D Stop

Start

Lap


Stopwatch number

Stopwatch number


1/100 seconds




11

Using the Target Time Alarm

OverviewAfter you configure one or more target times,the watch will beep and display an alert to letyou know when the elapsed time reaches atarget time.If you want to try running five kilometers in 30minutes, for example, you could set the targettimes shown below and monitor your pace foreach kilometer.Target Time 1: 6 minutesTarget Time 2: 12 minutesTarget Time 3: 18 minutesTarget Time 4: 24 minutesTarget Time 5: 30 minutes

Specifying a Target TimeYou can specify up to 10 target times,spanning a total range of 24 hours, in one-second units.● If you want to specify multiple target times,

specify the smallest time as Target Time 1,and the successive times in ascendingorder (Target Time 2, Target Time 3, etc.)

1. While the stopwatch is reset to all zeros,hold down (A) for at least two seconds.Release the button when [TGT] appears.● You can toggle the Target Time function

between enabled and disabled bypressing (D).

● [TGT] is shown on the display while theTarget Time function is enabled.

2. Press (C).3. Use (B) and (D) to select a target time

number.

Target time number

4. Press (C).5. Use (B) and (D) to change the target time

hour setting.Hours


minute setting.Minutes


second setting.Seconds

● If you want to specify multiple targettimes, repeat steps 2 through 9 above.


Measuring Elapsed Time with theTarget Time Function

You can perform the same elapsed timeoperations as those described in the sectionsbelow.lMeasuring Elapsed TimelMeasuring a Split TimelMeasuring Lap TimesStarting an elapsed time operation will cause[TGT] to flash on the display.An alarm will sound for 10 seconds to let youknow when the elapsed time operationreaches a target time you set.[TGT] disappears from the display when theelapsed time operation exceeds the last targettime.

Note

● [TGT] will appear if you stop timemeasurement while there is one ormore target time remaining.

Clearing a Specific Target TimeUse the procedure below to clear a selectedtarget time.

1. While the stopwatch is reset to all zeros,hold down (A) for at least two seconds.Release the button when [TGT] appears.

2. Press (C).3. Use (B) and (D) to the number of the target

time you want to clear.

Target time number


12

4. Press (C).5. Hold down (B) and (D) at the same time

for at least two seconds. Release thebuttons when the selected target timebecomes [0:00 00].This indicates that the selected target timewas cleared.

6. Press (A) to complete the operation.

Clearing All Target TimesThe procedure below restores all target timesto their initial factory defaults.● Target Time 1: 5 minutes● Target Time Function: Off

1. While the stopwatch is reset to all zeros,hold down (A) for at least two seconds.Release the button when [TGT] appears.

2. Hold down (B) and (D) at the same timefor at least five seconds. Release thebutton when [ALL CLR] stops flashing.This restores target time settings to theirinitial factory defaults.

3. Press (A) to complete the operation.

Managing Data Records

Viewing Lap/Split RecordsYou can use the operation below to view splittimes and lap times.

1. Enter the Recall Mode.l Navigating Between Modes● This causes the record number of the

latest measurement to appear.Record number

2. Hold down (A) for at least two seconds tocycle through record numbers.● Each time you hold down (A), the next

older record number appears.

A

A

A

A

2 seconds

2 seconds

2 seconds

2 seconds

3. Use (D) and (B) to display themeasurement value you want.

D

B

● Press (A) to toggle the measurementvalue display between lap time and splittime.

A

SplitLap

Note

● A record of the measured data iscreated and assigned a number foreach measurement operation (fromstart to stop).

Deleting a Particular RecordUse the procedure below to delete a selecteddata record.

1. Enter the Recall Mode.l Navigating Between Modes

2. Hold down (A) for at least two seconds.● Holding down (A) switches the record

number.

Record number

3. Hold down (B) and (D) at the same timefor at least two seconds. Release thebuttons when [CLR] stops flashing.● This deletes the displayed data.

Note

● You cannot delete data while anelapsed time measurement operationis in progress.


13

Deleting All RecordsYou can use the procedure below to clear alldata records in watch memory.

1. Enter the Recall Mode.l Navigating Between Modes

2. Hold down (B) and (D) at the same timefor at least five seconds. Release thebutton when [ALL CLR] stops flashing.[CLR] flashes and then stops flashing toindicate that the displayed data recordwas deleted. Keeping the buttonsdepressed will cause [ALL CLR] to flashon the display. [ALL CLR] will stopflashing to indicate that all data recordshave been deleted.

Note

● You cannot delete data while anelapsed time measurement operationis in progress.

TimerThe timer counts down from a start timespecified by you. The watch beeps everysecond for the last five seconds of thecountdown.● The beeper is muted in the cases described

below.ーWhen battery power is low.

Getting ReadyEnter the Timer Mode.l Navigating Between Modes

Setting a Timer Start TimeA timer start time can be set in 1-second unitsup to 60 minutes. The procedure below showshow to configure a single timer for acountdown.● If a timer countdown operation is in

progress, reset the timer to its current starttime before performing this operation.l Using the Timer

1. Hold down (A) for at least two seconds.Release the button when the number oftimer auto repeats setting (01 to 20) startsto flash.

Number of repeats

2. Use (D) and (B) to specify [01] as thenumber of timer auto repeats.

Number of repeats

3. Press (C).4. Use (D) and (B) to display [1].

5. Press (C).This causes the minutes digits to flash.

6. Use (D) and (B) to change the timerminutes setting.

Minutes

7. Press (C).This causes the seconds digits to flash.

8. Use (D) and (B) to change the start timeseconds setting.

Seconds


Using the Timer

A typical operation is shown below.

D

D

D

(Time up)

Resume

Pause

(Measurement operation starts.)

Start

● The watch beeps every second for the lastfive seconds of the countdown.

● To stop a countdown operation, first pauseit and then press (B). This will reset the timerto its start time.

Measuring Elapsed Time withAuto Start

You can use the procedure below so a timercountdown starts automatically following afive-second pre-count.

Five countdown seconds remaining

A typical operation is shown below.B

D

D

D

(Time up)

Resume

Pause

(Countdown starts)

(5-second pre-count)

Start

Enables Auto Start.

● To stop a countdown operation, first pauseit and then press (B). This will reset the timerto its start time.


14

Using the ProgrammableTimer as an Interval Timer

OverviewYou can configure settings for multiple timersso they perform different count downs oneafter the other to create an interval timer. Youcan use an interval timer to control how muchtime you spend doing push-ups, squats, orother exercises that make up a fitnessworkout.For example, you could configure an intervaltimer as shown below and have intervals Athrough D repeat 10 timesTimer Settings● Interval 1: 30 seconds● Interval 2: 20 seconds● Interval 3: 30 seconds● Interval 4: 25 seconds● Sets: 10Interval Training Workout

A Push-ups: 30 seconds

B Rest: 20 seconds

C Squats: 30 seconds

D Rest: 25 seconds

Note

● You can configure up to five differenttimers to repeat up to 20 times (AutoRepeat).

Configuring Settings for an IntervalTimer

● If a timer countdown operation is inprogress, reset the timer to its current starttime before performing this operation.l Using the Timer

1. Hold down (A) for at least two seconds.Release the button when the number oftimer auto repeats setting (01 to 20) startsto flash.

Number of repeats

2. Use (D) and (B) to specify the number oftimer auto repeats.

3. Press (C).4. Use (D) and (B) to specify the position of

the timer in the sequence.● To specify the first position, set [1].

5. Press (C).This causes the minutes digits of Timer 1to flash.

6. Use (D) and (B) to change the timerminutes setting.

Minutes

7. Press (C).This causes the seconds digits of Timer 1to flash.

8. Use (D) and (B) to change the start timeseconds setting.

Seconds

9. Press (C) twice.This returns to the screen in step 4.

10. Repeat steps 4 through 9 as many timesas necessary to configure the settings ofthe other timers.


Using an Interval Timer

1. Press (D) to start the countdown.

The watch beeps every second for the lastfive seconds of the current countdown,and starts the countdown of the next timerwhen the end is reached.● To pause an ongoing timer countdown,

press (D). To reset a pausedcountdown to its start time, press (B).

● When there is a multiple timercountdown operation in progress, youcan immediately terminate the currentcountdown and start the nextcountdown by pressing (A).

Dual TimeDual Time lets you look up the current time invarious time zones around the globe.

Getting ReadyEnter the Dual Time Mode.l Navigating Between Modes


15

Configuring Dual TimeSettings

Dual Time lets you set the current time inanother time zone in addition your currentlocation time.

1. Hold down (A) for at least two seconds.Release the button when the hour digitsstart to flash.

Hours

2. Use (D) and (B) to change the hour setting.3. Press (C).

This causes the minutes digits to flash.Minutes

4. Use (D) and (B) to change the minutesetting.● You can change the setting in 15-

minute increments.5. Press (A) to exit the setting screen.

Swapping the Home CityTime and Dual Time

1. Enter the Dual Time Mode.l Navigating Between Modes

2. Hold down (B) for at least 2 seconds.This swaps the Home City time and DualTime.

After swappingBefore swapping

Dual Time

Dual TimeCurrent location time

Current location time

Note

● This function comes in handy whenyou need to move to another timezone. For details about how to use it,go to the section below.lMoving to Another Time Zone

Alarms and Hourly TimeSignal

The watch will beep when an alarm time isreached. You can set up to five differentalarms. The hourly time signal causes thewatch to beep every hour on the hour.Getting ReadyEnter the Alarm Mode.l Navigating Between Modes

Configuring Alarm Settings

1. Press (D) to scroll through alarm numbers([AL1] to [AL5]) until the number of thealarm you want to configure is displayed.

Alarm number

2. Hold down (A) for at least two seconds.Release the button when the hour digitsstart to flash.

Hours

3. Use (D) and (B) to change the hour setting.● If you are using 12-hour timekeeping,

[P] indicates p.m.


16

4. Press (C).This causes the minutes digits to flash.

Minutes

5. Use (D) and (B) to change the minutesetting.


Note

● A beeper will sound for 10 seconds tolet you know when the alarm time isreached.

Enabling/Disabling an Alarmor the Hourly Time Signal

1. Press (D) to scroll through alarm numbers([AL1] to [AL5]) and the hourly time signal([SIG]) screens until the one you want toconfigure is displayed.

Alarm or hourly time signal

2. Press (B) to toggle the displayed alarm orthe hourly time signal between on and off.[On]: On[--]: Off

Stopping an AlarmPressing any button while the beeper issounding stops it.

Determining an Alarm’sOn/Off Status

Turning on an alarm or the hourly time signalcauses the corresponding indicator to appearon the display. The alarm on indicator isdisplayed when one or more alarm is turnedon.

Hourly time signal

Alarm

Adjusting the TimeSetting Manually

When there is no communication with aphone, the time and date can be adjusted withthe procedure below.Getting ReadyEnter the Timekeeping Mode.l Navigating Between Modes

Setting the Time and Date


2. Keep pressing (C) until the setting youwant to change is flashing.● Each press of (C) moves the flashing to

the next setting in the sequence shownbelow.

Day

Month

Year

Minute

Hour

Seconds

12/24-hour timekeeping

Illumination duration

Operation tone enable/disable

Daily step target

Step Reminder On/Off


17

3. Configure the date and time settings.● To reset the seconds to 00: Press (D).

1 is added to the minutes when thecurrent count is between 30 and 59seconds.

● To change other settings: Use the (D)and (B) buttons.

4. Repeat steps 2 through 3 to configure dateand time settings.


Switching Between 12-hourand 24-hour Timekeeping


2. Press (C) five times so the current setting([12H] or [24H]) is flashing on the display.

3. Press (D) to toggle the setting between[12H] (12-hour timekeeping) and [24H](24-hour timekeeping).


Note

● While 12-hour timekeeping isselected, [P] will be displayed for p.m.times.

Illumination LightThe watch has an LED light that you can turnon for reading in the dark.

Illuminating the FaceManually

Pressing (L) turns on illumination.

● The LED light will turn off automatically if thealarm starts to sound.

Auto LightIf Auto Light is enabled, the face illuminationwill turn on automatically whenever the watchis positioned at an angle of 40 degrees ormore.l Configuring the Auto Light Setting

40 degrees or more

Important!

● Auto Light may not operate properlywhen the watch is at a horizontal angleof 15 degrees or greater fromhorizontal as shown in the illustrationbelow.

● Electro-static charge or magnetismcan interfere with proper auto lightoperation. If this happens, try loweringyour arm and then angle it towardsyour face again.

● When moving the watch you may notea slight rattling sound. This is due tooperation of the auto light switch,which determines the currentorientation of the watch. It does notindicate malfunction.

Note

● Auto Light is disabled when any one ofthe conditions below exists.ーAlarm, timer alert, or other beeper

soundingーHand movement operation is in

progress

Configuring the Auto LightSetting

Holding down (L) for at least three seconds inthe Timekeeping Mode will toggle Auto Lightbetween enabled and disabled.● [LT] is displayed while Auto Light is

enabled.● Auto Light remains enabled for

approximately six hours. After that, itbecomes disabled automatically.

On

Specifying the IlluminationDuration

You can select either 1.5 seconds or threeseconds as the illumination duration.



3. Press (C) 10 times to display [LT].4. Press (D) to toggle between the two

illumination duration settings.[1]: 1.5-second illumination[3]: 3-second illumination



18

Hand AlignmentAdjustment

Strong magnetism or impact can cause thetime indicated by the analog hands to becomedifferent from the time on the digital display. Ifthis happens, adjust hand alignment.Getting ReadyEnter the Timekeeping Mode.l Navigating Between Modes

Adjusting Hand Alignment


2. Hold down (A) for at least five seconds.Release the button when [12:00] starts toflash.This enables adjustment of the hour andminute hands.

After five secondsAfter two seconds

3. If the hour hand and minute hand are notat 12 o’clock, use the (D) and (B) buttonsto align them.


Battery ReplacementWhen battery power goes low, will start toflash and some functions will becomedisabled. If continues to flash, replace thebattery.

Other SettingsGetting ReadyEnter the Timekeeping Mode.l Navigating Between Modes

Enabling the ButtonOperation Tone

Use the procedure below to enable or disablethe tone that sounds when you press a button.



3. Press (C) nine times to display [♪].

4. Press (D) to toggle the button operationtone between enabled and disabled.[On]: Operation tone enabled.[OFF]: Operation tone disabled.


Moving to Another TimeZone

Use the procedure below to easily change dayand time settings of the watch to a destinationlocation.

● Before Boarding

1. Configure the World Time (Dual Time)setting to the current time at yourdestination.

Destination time

Current time

l Using BABY-G Connected toConfigure Settings

l Using Watch Operations to ConfigureSettings

2. Disable auto time adjustment.

l Using the Watch in a Medical Facility orAircraft


19

● In the aircraft, before arriving at yourdestination

1. Swap the origin time zone time with thedestination time zone time.

After swappingBefore swappingDestination time

Destination time

l Using BABY-G Connected toConfigure Settings

l Using Watch Operations to ConfigureSettings

● After Arriving

1. Adjust the time setting.l Triggering Immediate Time

Adjustment2. Enable auto time adjustment.l Using the Watch in a Medical Facility or

Aircraft

Other InformationThis section provides non-operationalinformation you also need to know. Refer tothis information as required.

Supported PhonesFor information about phones that canconnect with the watch, visit the CASIOwebsite.https://world.casio.com/os_mobile/wat/

SpecificationsAccuracy at normal temperature :

±15 seconds per month average when timeadjustment by communication with a phoneis not possible.

Timekeeping :Analog

Hour, minute (moves every 20 seconds)Digital

Hour, minute, second, month, day, day ofthe week, a.m./p.m. (P)/24-hour timeformat, full auto calendar (2000 to 2099)

Pedometer :Step count measurement using a 3-axisaccelerometerStep count display range: 0 to 999,999 stepsStep indicatorStep count graphStep count reset

Auto zero-reset at midnight each dayManual reset

Daily step goal settingStep count setting unit: 1,000 stepsStep count setting range: 1,000 to 50,000steps

Daily Step Target Attainment AlertStep ReminderStep count accuracy

±3% (According to vibration testing)Power SavingStopwatch/Data Recall :

Measuring unit1/100 seconds (first hour); 1 second(after first hour)

Measuring range: 23 hours 59 minutes 59secondsMeasurement Functions:

Normal elapsed time; cumulative time;lap/split times; 200-record data memory

Target time alarm:Up to 10 time settings; watch beeps (for 10seconds) when a target time is reached

Timer :Measuring unit: 1 secondMeasuring range: 60 minutesNumber of intervals: 1 to 5Number of auto repeats: 1 to 20Time setting unit: 1 secondTime setting range: 1 second to 60 minutesFinal 5-second countdown, time-up beeperAuto Start

Dual Time :Hour, minute, secondHome Time swapping

Alarm :Time alarmsNumber of alarms: 5Setting units: Hours, minutesAlarm tone duration: 10 secondsHourly time signal: Beep every hour on thehour

Mobile Link :Auto Time Correction

Time setting adjusted automatically atpreset time.

One-touch Time CorrectionManual connection and time adjustment

Phone finderWatch operation sounds the alert soundof the phone.

World TimeCurrent time for approximately 300 citiesselected for the watchHome Time/World Time swapping

Step count data transferStep count, calories

Stopwatch data transfer200 lap/split time records (date and time,lap/split time, lap number)

Auto Summer Time SwitchingAutomatic switching between standardtime and summer time.

Timer SettingsAlarm SettingsHand alignment correctionData Communication Specifications

Bluetooth®

Frequency Band: 2400MHz to 2480MHzMaximum Transmission: 0 dBm (1 mW)Communication range: Up to 2 meters(depends on environment)

Other :High-brightness LED light; illuminationduration setting; Auto Light; operation toneon/off; Hand Shift; low battery alert

Power Supply :CR2016 x 1Battery life: Approximately 2 yearsConditions

Auto time correction: 4 times/dayAlarm: Once (10 seconds)/dayIllumination: Once (1.5 seconds)/dayStep counting: 12 hours/day

Specifications are subject to change withoutnotice.


20

https://world.casio.com/os_mobile/wat/

Mobile Link Precautions● Legal Precautions● This watch complies with or has received

approval under the radio laws of variouscountries and geographical areas. Usingthis watch in an area where it does notcomply with or has not received approvalunder applicable radio laws may be acriminal offense. For details, visit the CASIOWebsite.https://world.casio.com/ce/BLE/

● Use of this watch inside of aircraft isrestricted under the aviation laws of eachcountry. Be sure to follow the instructions ofairline personnel.

● Precautions when using Mobile Link● When using this watch in combination with

a phone, keep the watch and phone closeto each other. A range of two meters isrecommended as a guideline, but the localenvironment (walls, furniture, etc.), thestructure of a building, and other factorsmay require a much closer range.

● This watch can be affected by other devices(electrical devices, audio-visual equipment,office equipment, etc.) In particular, it canbe affected by operation of a microwaveoven. The watch may not be able tocommunicate normally with a phone if amicrowave oven is operating nearby.Conversely, this watch may cause noise inradio reception and the video image of a TV.

● Bluetooth of this watch uses the samefrequency band (2.4 GHz) as wireless LANdevices, and use of such devices in closeproximity of this watch may result in radiointerference, slower communicationspeeds and noise for the watch and thewireless LAN device, or evencommunication failure.

● Stopping Radio Wave Emission by ThisWatch

The watch is emitting radio waves whenevere is displayed.Even if e is not displayed, the watch willautomatically attempt to connect with a phonefour times a day to adjust its time settings.When in a hospital, on an aircraft, or in anyother area where the use of radio waves is notallowed, use the operations below to stopradio wave generation.● Stopping Radio Wave GenerationPress any button besides (L) to terminate theBluetooth connection.

Connected Disconnected

● Disabling Auto Time AdjustmentConfigure BABY-G Connected settings todisable time adjustment between the watchand phone.l Using the Watch in a Medical Facility or

Aircraft

Copyrights and RegisteredCopyrights

● The Bluetooth® word mark and logos areregistered trademarks owned by theBluetooth SIG, Inc. and any use of suchmarks by CASIO Computer Co., Ltd. isunder license.

● iPhone and App Store are registeredtrademarks of Apple Inc. in the UnitedStates and other countries.

● iOS is a trademark or registered trademarkof Cisco Systems, Inc.

● GALAXY is a registered trademark ofSamsung Electronics Co., Ltd.

● Android and Google PlayTM are trademarksor registered trademarks of Google LLC.

● Other company names and product namesused herein are trademarks or registeredtrademarks of their respective companies.

Troubleshooting

I can’t pair the watch with aphone.

Q1 I’ve never been able to establish a(pairing) connection between thewatch and phone.

Are you using a supported phone model?Check if the phone model and itsoperating system are supported by thewatch.For information about supported phonemodels, visit the CASIO Website.https://world.casio.com/os_mobile/wat/

Did you install BABY-G Connected onyour phone?

BABY-G Connected needs to be installedon your phone in order to connect with thewatch.lA Install the app on your phone.

Are your phone’s Bluetooth settingsconfigured correctly?

Configure the phone’s Bluetooth settings.For details about setting procedures, seeyour phone documentation.iPhone Users● “Settings”n“Bluetooth”n OnAndroid Users● Enable Bluetooth.

Other than the above.Some phones need to have BT Smartdisabled to use BABY-G Connected. Fordetails about setting procedures, see yourphone documentation.On the Home Screen, tap: “Menu” n“Settings” n “Bluetooth” n “Menu” n “BTSmart settings” n “Disable”.


21

https://world.casio.com/ce/BLE/

https://world.casio.com/os_mobile/wat/

I can’t reconnect the watchand phone.

Q1 The watch will not re-connect with thephone after they are disconnected.

Is BABY-G Connected running?The watch cannot re-connect with thephone unless BABY-G Connected isrunning on the phone. On the phoneHome Screen, tap the “BABY-GConnected” icon.Next, on the watch, hold down the MODEbutton (C) for at least two seconds to enterthe Timekeeping Mode. After that, holddown the CONNECT button (D) for atleast two seconds to establish aconnection between the watch andphone.

Have you tried turning your phone off andthen back on again?

Turn the phone off and then back onagain. On the Home Screen, tap the“BABY-G Connected” icon.Next, on the watch, hold down the MODEbutton (C) for at least two seconds to enterthe Timekeeping Mode. After that, holddown the CONNECT button (D) for atleast two seconds to establish aconnection between the watch andphone.

Is a stopwatch or timer operation beingperformed?

The watch cannot connect with a phonewhile a stopwatch measurement or timeroperation is in progress. Wait until thestopwatch or timer operation is completebefore connecting with the phone.

Q2 I can’t connect while my phone is inthe Airplane Mode.

After exiting the phone’s Airplane Mode, go toits Home Screen and tap the “BABY-GConnected” icon.Next, on the watch, hold down the MODEbutton (C) for at least two seconds to enter theTimekeeping Mode. After that, hold down theCONNECT button (D) for at least two secondsto establish a connection between the watchand phone.

Q3 I changed the phone’s Bluetoothfrom enabled to disabled, and now Ican’t connect anymore.

On the phone, change the Bluetooth settingfrom disabled to enabled, and then go to theHome Screen and tap the “BABY-GConnected” icon.Next, on the watch, hold down the MODEbutton (C) for at least two seconds to enter theTimekeeping Mode. After that, hold down theCONNECT button (D) for at least two secondsto establish a connection between the watchand phone.

Q4 I can’t connect after turning off thephone.

Turn on the phone. On the Home Screen, tapthe “BABY-G Connected” icon.Next, on the watch, hold down the MODEbutton (C) for at least two seconds to enter theTimekeeping Mode. After that, hold down theCONNECT button (D) for at least two secondsto establish a connection between the watchand phone.

Phone-Watch Connection

Q1 I can’t establish a connectionbetween the phone and watch.

Have you tried turning your phone off andthen back on again?

Turn the phone off and then back onagain. On the Home Screen, tap the“BABY-G Connected” icon.Next, on the watch, hold down the MODEbutton (C) for at least two seconds to enterthe Timekeeping Mode. After that, holddown the CONNECT button (D) for atleast two seconds to establish aconnection between the watch andphone.

Has the watch been re-paired with thephone?

After deleting pairing information fromBABY-G Connected, re-pair them.l Unpairing

If you are unable to establish aconnection...

Use the procedure below to delete thepairing information from the watch, andthen re-pair the watch and phone.A Hold down (C) for at least two secondsto enter the Timekeeping Mode.B Hold down (A) for at least two seconds.Release the button when the StepReminder settings screen ([OFF] or [ON]flashing) appears.C Hold down (B) until [CLR] stopsflashing on the display.D Press (A) to exit the setting screen.


22

Changing to a DifferentPhone Model

Q1 Connecting the current watch toanother phone.

Pair the watch with the phone.l If you purchase another phone

Auto Time Adjustment byBluetooth Connection (TimeAdjustment)

Q1 When does the watch adjust is time?The watch will connect with the phone andperform auto time adjustment at around 12:30a.m., 6:30 a.m., 12:30 p.m. and 6:30 p.m. Theconnection is automatically terminated afterauto time adjustment is complete.

Q2 Auto time adjustment does not start.

Did you recently swap your Home Timeand World Time, or manually adjust thewatch’s time setting?

Note that auto time adjustment is notperformed for 24 hours after swapping ofthe Home Time and World Time, or afterthe time setting is adjusted manually onthe watch. Auto time adjustment willresume 24 hours after either of the aboveoperations is performed.

Is auto time adjustment enabled?Auto time adjustment will not beperformed at the scheduled times unlessit is enabled. Enable auto timeadjustment.l Using the Watch in a Medical Facility or

Aircraft

Q3 Time is not displayed correctly.The phone’s time setting may be incorrectbecause it is unable to connect with itsnetwork due to being out of range, etc. If thishappens, connect the phone to its networkand then adjust the time setting.

Pedometer

Q1 Displayed step count is not correct.While the watch is on your wrist, thepedometer may detect non-step movementsand count them as steps.Also, step count problems can also be causedby how the watch is being worn and abnormalarm movement while walking.l Counting Steps

Q2 The step count does not increase.The step count is not displayed at thebeginning of a walk in order to avoidmiscounting of non-walking movements.It appears only after you have continuedwalking for about 10 seconds, with the numberof steps you took during the first 10 secondsincluded in to the total.

Q3 [ERR] appears when using thepedometer.

[ERR] (error) appearing on the displayindicates malfunction of the sensor or internalcircuitry, making sensor readings impossible.If the message does not disappear after aboutthree minutes or if it keeps appearing, it mayindicate sensor malfunction.

Alarm

Q1 The alarm does not sound.Is the alarm setting turned on? If it isn’t, turn iton so it will sound.l Enabling/Disabling an Alarm or the Hourly

Time Signal

Hand Movement andIndications

Q1 I don’t know what mode the watch isin.

You can determine the current mode bychecking the watch display. Use (C) tonavigate between modes.l Navigating Between Modes

Q2 All hands are stopped and buttons donot work.

The battery is dead. Request batteryreplacement by your original retailer orauthorized CASIO service center.l Battery Replacement

Q3 The hands suddenly start moving athigh speed.

This is due to one of the reasons below, anddoes not indicate malfunction. Simply waituntil normal hand movement resumes.● Watch is connected with a phone to adjust

its time setting.l Auto Time Adjustment

Q4 The current time indicated by thewatch is off by one hour or 30minutes.

The summer time setting is not correct. Selectthe correct setting.l Changing the Home City Summer Time

Setting

Q5 The time indicated by the hands isdifferent from the digital time.

Strong magnetism or impact can cause thehands to go out of alignment. Adjust handalignment.l Adjusting Hand Alignment● Check the information below to find out how

to align the hands manually.l Hand Alignment Adjustment


23

Battery

Q1 is flashing on the digital display.This indicates that battery power is gettinglow. Request battery replacement by youroriginal retailer or authorized CASIO servicecenter.l Battery Replacement

Q2 [R] is flashing on the digital display.This happens when battery power is low orafter the light or some other function is turnedon repeatedly over a short amount of time,which temporarily runs down the battery. Allfunctions other than timekeeping are disabledwhile [R] is flashing on the display.If [R] remains on the display or if it keepsappearing, it may indicate that the batteryneeds to be replaced.Request battery replacement by your originalretailer or authorized CASIO service center.


24

Documents

Timekeeping Indicators Measuring Lap Times …...it on your phone. B Configure Bluetooth settings. Enable the phone’s Bluetooth. Note For details about setting procedures, see your