TM Vacuum Cleaning System - Spencer Turbine

Spencer® Industravac® V-JetTM Series Vacuum Cleaning System

Handling, Installing andOperating Instructions

Serial No:

Model No:

Filter Bags:

IMPORTANT Do not operate machine in unstable, low-flow range (surge).

Read and become familiar with this manual prior to installing Spencer Industravac V-Jet equipment. Following these instructions will help you realize the product’s full potential of efficient service and long life. Damage resulting from failure to follow correct procedures will void the warranty.

The Spencer Turbine Company Windsor, Connecticut 06095 Form IVJ

www.spencerturbine.com


2

4.375 x 3.25

V-Jet

™ Series

Read instructions before handling and starting equipment

Made in U.S.A. Plate No. PLN90181

Manufactured under the following Registered Trademarks:62,801; 140,976; 652,701; 1,284,095; 134,026; 341,418; 595,313;1,348,270; 959,254; 7,218,205; 7,218,284; 7,218,285; 7,218,286

Serial No.

Model No.

4.375 x 3.25

V-Jet

™ Series

Read instructions before handling and starting equipment


Manufactured under the following Registered Trademarks:62,801; 140,976; 652,701; 1,284,095; 134,026; 341,418; 595,313;1,348,270; 959,254; 7,218,205; 7,218,284; 7,218,285; 7,218,286

The Spencer Turbine Company, Windsor, CT 06095800-232-4321 860-688-8361


Use Original Factory Parts & Service





Serial No.

Model No.

ContentsPage

I. Warranty 2 II. General Introduction 2 III. Getting Started 2 IV. Operation and Adjustments 6 V. Maintenance 6 Vl. Troubleshooting Guide — Separator 8 Vll. Troubleshooting Guide — Vacuum Producer 9

I. WarrantyWe warrant that this product will be free from defects in materials and workmanship for a period of 18 months from date of shipment or 12 months from date of start-up, whichever comes first. Within the warranty period, we shall repair or replace, F.O.B. our Factory, such products that are determined by us to be defective.

This warranty will not apply to any product which has been subjected to misuse, negligence, or accident or misapplied or improperly installed. This warranty will not apply to any product which has been disassembled, repaired or otherwise altered by any persons not authorized by our Service Department.

The guarantee of the motor and control manufacturers will govern the extent of our guarantee on such equipment.

Refer to Bulletin 706 for complete terms and conditions.

II. General Introduction

Before proceeding with set-up, record the machine catalog number and serial number in the boxes on the front cover of this manual. These numbers may be found on the nameplate located on the vacuum producer casing. Also record the filter bag number for convenient reordering. Having this information easily accessible will expedite parts orders and other commu-nication with the factory, ensuring prompt, accurate service.

Description

The Industravac V-Jet Series unit consists of a multistage centrifugal vacuum producer with continuous duty motor; a tubular-bag two-stage separator and heavy-duty size dirt can for debris collection. These components form a dependable, heavy-duty vacuum cleaning system that is designed and rated for continuous operation handling dry, free-flowing materials.

The vacuum producer can be interconnected with tubular bag separator and dirt can, or the two components can be installed in separate locations.

CAUTION: Standard Industravac V-Jet units must not be used for liquid pickup or for vacuuming volatile, viscous, flammable or explosive materials.

NOTE: When connecting to tubing system, check for leaks before enclosing tubes in walls.

III. Getting StartedNOTE: If any problems are encountered during installation or start-up of your Industravac V-Jet system, consult your local Spencer Representative.

Moving and HandlingUnit is carefully balanced and tested at the factory. For optimum performance, it must be handled with care during installation. Using accepted rigging practices and safety precautions, the unit can be lifted and relocated with a forklift or pallet jack.

NOTE: Remove the dirt can from separator for access to fork lift or pallet jack slots.

StorageIf the machine is to be stored for an extended period, it must be protected from dampness, dirt and vibration. The inlet and discharge should be covered to keep foreign matter out.

3

Detail A(Coupling)

Typical Industravac V-Jet Assembly

ExternalBag Shaker

InvertedFilter Bags

AdjustableDoor Latches

SeparatorTube Inlet

Dirt CanLocking Bail

Dirt Can

Filter BagBuckle

Lift Cam

LeverClamp

CamArm

Bag HeadSpring

Vacuum Inlet Valve for1-1/2" Hose (Standard)

Rubber Spacers and Fasteners

ContinuousDuty Motor

MotorAccess Door

Sleeve

MultistageCentrifugalVacuumProducer

Impellers andDeflectors

Connector Sleeveand Clamps

Silencer Box

VacuumProducerInlet

Inlet Elbow

Separator Outlet

Target PlatePatent No. 4,874,410

OptionalEqualizing Line

Two-StageSeparator

SeparatorAccess Door

DoorGasket

Fork Lift orPallet Jack Access

Hub

Fork Lift orPallet Jack Access

BearingHousing

Coupling(see Detail A)

MotorBracket

4

Location

Industravac V-Jet vacuum producers are designed for operation at or near sea level atmospheric pressure and a nominal ambient temperature of 70 °F (21 °C). When necessary, they can be factory-designed for higher altitude or higher temperature operation.

Installation

No special foundation is required. A level concrete floor or pad is recommended, although any substantial floor is satisfactory. The Industravac V-Jet base should be placed on rubber isolation pads furnished with the unit.

Be sure installation area is accessible for servicing by allowing several feet of clearance. The exhaust should discharge outdoors which requires an optional tubing adapter, or into a room with volume and sufficient ventilation to allow air to escape. Avoid placing the unit in an enclosed room. Ambient temperature should not exceed 104 °F (40 °C).

Unpacking

NOTE: The Industravac V-Jet ships on two skids; vacuum producer on one skid; separator positioned horizontally on another skid.

1. Uncrate the Industravac V-Jet components, saving all literature, boxes and parts.

2. Remove packing materials and plugs. Look inside dirt can for parts and accessories (equalizing line, dirt can liners, hoses, isolation pads, etc.) packed inside for shipping purposes.

3. Refer to the packing slip to verify all components ordered are received.

Industravac V-Jet Set-Up

NOTE: Read all instructional and warning labels on the machine components before handling and operating.

1. Connecting Components. Slide rubber sleeves and clamps over each end of the inlet elbow. Insert one end of the inlet elbow into the separator outlet and the other end into the vacuum producer inlet. Tighten rubber sleeve clamps. At the base of the separator and vacuum producer, insert the rubber spaces and fasteners and tighten.

2. Separator. Open the separator access door to confirm that the door gasket and filter bags are in place and secure. With the door open, operate the external bag shaker to check for proper action. Close separator access door.

Move the dirt can to a lower position to confirm that nothing has been left inside, and check that the dirt can gasket is in place beneath the separator. Raise the dirt can and ensure seal is tight against the gasket. Inspect both separator inlet ports to confirm that ports are clear.

If optional dirt can liners will be used, install one liner in the dirt can and make sure the equalizing line is in place, properly connected to the separator and dirt can.

CAUTION: The dirt can liner must not be used without the equalizing line, as the liner will be sucked out of the can, up against the filter bags. Conversely, do not use the equalizing line without the dirt can liner. Mechanical and environmental damage may result.

CAUTION: If the separator is equipped with an optional explosion relief port, it must be installed in accordance with the National Fire Code and all applicable safety regulations. The port should be positioned away from nearby personnel and ducted to the outdoors.

3. Electrical.

NOTE: All wiring and electrical adjustments or installations should be done by a qualified electrician in accordance with the National Electrical Code and local codes.

The Industravac V-Jet vacuum producer is furnished with a C-Face, premium-efficient TEFC motor designed for 60 Hz, 3 phase, 200-230/460 operation.

NOTE: The electrical service at the installation site must supply the voltage stamped on the motor nameplate. Operation at an incorrect voltage will result in a damaged motor.

To make electrical connections, follow the wiring instructions furnished. All wiring, power cords and circuit breakers should be of ample capacity to ensure that proper voltage is maintained at the motor terminals while starting and running. Starters should have thermal overload protection and low-voltage protection.

Electrical Accessories. Optional accessories such as an Electronic Modulating Bleed Control and motorized filter bag shaker require 115VAC, single-phase electrical service. They should be installed using the separate instruction sheets accompanying them.

A grounding lug is provided for optional grounded filter bags. To effectively bleed off static electricity charges, this lug should be securely connected to an electrical ground.

4. Motor Rotation. Perform a pre-start check to ensure the motor turns in the correct direction. A rotation direction arrow is located on the vacuum producer casing. To confirm that the motor is wired correctly, momentarily start the motor. “Bump” or jog the start button and observe the direction of rotation at either the end bell of the motor or the motor shaft, whichever is visible. If the rotation is incorrect, reverse the motor wiring.

Note: The vacuum producer will operate both ways; with incorrect rotation, unit will produce insufficient suction.

5

Industravac V-Jet Dimensions

6

V. MaintenanceCAUTION: Disconnect electrical power before performing any maintenance procedure.

1. LubricationNOTE: The housing does not require lubrication. Follow the steps below to ensure the correct components are lubricated properly.

1. Motor. Follow motor manufacturer’s recommendations.

Regarding items 2 through 4, apply light lubricating oil yearly or more often as needed.

2. Bag shaker rod. Grease more often than yearly if application requires more lubrication.

3. Lift cams. Lubricate both left- and right-hand cams.

4. Dirt can casters.

2. Vacuum Producer –Multistage Centrifugal (Series V-Jet)NOTE: For maintenance of the motor, consult motor manu-facturer’s information, provided with the equipment.

NOTE: To preserve the warranty, ensure that disassembly, repair or alteration is never done by unauthorized personnel during the warranty period. The maintenance instructions that follow are provided as a customer service to facilitate field repair after the warranty period.

If operating problems are detected, notify your local Spencer Representative.

Disassembly / Re-assembly procedure

CAUTION: This procedure assumes that electrical power and piping have been disconnected and that unit has been taken out of service.

Disassembly – Motor Section

1. Shut down and lock out electrical power supply to motor.

2. Remove door held in place by (4) ¼-20 nuts and washers and set aside.

3. Place floor jack under motor and raise until it contacts bottom of motor.

4. Loosen set screw in coupling sleeve then slide sleeve toward motor.

5. Remove coupling element.

6. Remove (4) ½-13 screws and washers connecting motor bracket to bearing housing. Lower motor and bracket and remove from casing.

7. Loosen set screws on coupling sleeve, then remove coupling hub and keyway from impeller shaft.

Disassembly – Top Section1. Remove end head held in place by (16) sets of 3/8-16

screws, nuts and washers.

2. Remove retaining ring, steel shim, and if provided, any aluminum shims from shaft.

3. Slide top impeller from shaft. (Take care to ensure that when impellers and shims are reinstalled they are placed in the proper order as to not upset impeller balance integrity).

IV. Operation and Adjustments NOTE: The unit is designed for operation under load. For maximum performance, it must always be used as part of a system, which includes all of its components.

Machine Start-Up1. Turn the unit on after completing the previous set-up

procedures.

2. Check the tubing system and vacuum equipment for leaks. At the separator, check the access door, dirt can seal and hose inlet valves. Examine all hoses, tubes, and fittings connected to the Industravac V-Jet unit. Air leaks are highly detrimental to the overall system performance, wasting power and impairing the operating efficiency.

If unit is equipped with the following optional accessories:

Discharge air gate - With a full vacuum system load connected to the separator inlet(s), connect an ammeter to the motor circuit. Measure the amperage of the motor. If below the full-load current rating, open air gate until the amperage reaches, but does not exceed, the full-rated motor capacity. The air gate should then be fixed to prevent opening beyond this point.

Electronic Modulating Bleed Control (EMBC) - Follow adjustment instructions in the separate data sheet accompanying the EMBC.

CAUTION: When the vacuum producer is operating, its housing will be hot to the touch. Use caution when making inspections or adjustments in this area.

Surge (Low Flow Condition)

CAUTION: Do not operate vacuum producer in surge (unstable low-flow range). Damage to vacuum producer caused by operating in surge is not covered by Spencer warranty.

A vacuum producer in surge produces a rush or pulsating rhythmic air sound caused when airflow into or out of the vacuum producer is restricted. In addition to its characteristic noise, surge may be detected by power or pressure fluctuations. Surge is destructive because it is accompanied by excessive temperatures and aerodynamic forces that will ultimately cause mechanical failure. A surge condition is eliminated by increasing the airflow either into the system or to a bypass or vent. Various surge control devices are available from Spencer.

NOTE: If a vacuum producer surges violently at start-up, avoid recurrences by leaving the throttling valve open at or near its normal operating position.

Hose and tools

For optimum performance, Industravac V-Jet units have been designed and sized specifically for use only with complementary Spencer vacuum cleaning components—Spencer tubing, fittings, hoses, tools, attachments and accessories.

7

Top S

ection

1A+B End Head Gaskets

2 Impeller

3 Spacer

4 Deflector

5 Deflector Sealant

6A+B Bearings

7 Motor

1A

End Head

1B

3

4

5

6A+B

7

V-Jet VP Replacement Parts

Motor S

ection

2

4. Remove top spacer.

5. Using a suitable tool, remove sealant from deflector surfaces and remove from casing. Continue to remove impellers, shims, spacers, and deflectors taking note of order, as it is important during reassembly that this order is adhered to.

6. Remove key from keyway. Take care as to not damage shaft or key during removal.

7. Remove (4) sets of ½-13 screws, nuts, and washers (bearing housing to lower casing).

8. Install a suitable 5/8-11 eyebolt into end of shaft and carefully lift bearing housing assembly from casing.

NOTE: Top Section Casing (Housing) may have to be unbolted and removed if height clearance is not enough for removal of bracket.

NOTE: Ensure that eyebolt is threaded completely into shaft prior to lifting housing from casing.

Bearing Removal1. Remove top bearing cover retained by (6) sets of ¼-20

socket head cap screws and washers.

2. Press out coupling side bearing by exerting force to the fan end of the shaft.

3. Press out impeller side bearing using a suitable mandrel against inner bearing race.

4. Remove nut and washer from shaft, this will now allow bearing to be removed from shaft.

Bearing Replacement1. Press new bearing onto coupling side of shaft, replace

washer and tighten nut.

NOTE: Align tab on washer with slot in nut and bend over to ensure nut does not become loose.

2. Using Spencer bearing installation tool, install remaining bearing into bearing housing following instructions provided with tool.

3. Install cover.

4. Install key and coupling hub onto impeller shaft.

Re-assembly1. Install a suitable 5/8-11 eye bolt into end of shaft and

carefully lower assembled bearing housing into casing while aligning mounting holes.

NOTE: Ensure that eyebolt is threaded completely into shaft prior to lifting housing.

2. Install motor and bracket assembly - Ensure that coupling sleeve is still positioned below motor coupling hub. Raise motor using a lifting jack or floor jack until it makes slight contact with bearing housing while aligning mounting holes. Secure motor to bracket using (4) ½-13 screws and washers be sure to tighten screws in an even pattern.

3. Install element between the coupling hubs, slide the coupling sleeve back into place and tighten set screws.

4. Install fans, shims, spacers, and deflectors in proper order. Reseal spacer and deflector surfaces using Spencer sealant.

5. Install retaining ring.

6. Inspect end head gasket for damage and replace if necessary.

7. Install end head using (16) sets of 3/8-16 screws and washers taking care to tighten screws evenly.

8. Using a feeler gage adjust the gap between the coupling hub faces by sliding the coupling hub on the shaft to .078 +/- 10% then tighten set screws.

9. After motor is wired (be sure to phase for proper rotation), piping is installed, and unit is ready to be placed into service. Be sure to replace door.

8

Changing Filter Bags

Examine filter bags periodically and replace them when visibly worn. Also look for leaks, which are signaled by dirt on the outside of the bags or on the bag head or by dust in the discharge airstream.

1. To install a new filter bag, compress the spring collar at the bottom of the bag.

2. Insert the compressed spring collar into the bag head and allow it to resume its original shape.

3. Pull up on the bag to ensure that it is properly seated. The recess in the spring collar must be at the opening. Entire collar should not be below bag head.

4. Install buckle on the narrow tab of filter bag and attach to hook on shaker plate. Pull on tab end to remove slack.

It is recommended to keep a set of spare Spencer filter bags. In addition to standard cotton sateen filter fabric, various other materials are available with specialized properties suited to adverse conditions such as dampness, abrasion or chemical attack.

4. Replacement PartsProvide full information about equipment, including the serial number and catalog number, when ordering parts. When ordering replacement filter bags, provide bag-part number.

3. Separator

Shaking the Filter Bags

NOTE: The vacuum producer must be turned off during bag shaking, or loosened dirt will permeate the filter bags.

Press and release external bag shaker handle several times to loosen dirt that has accumulated inside the filter bags, allowing it to fall into the dirt can.

Emptying the Dirt Can

Lift the bail arm to lower the dirt can. Empty as needed on a regular basis, never allowing it to be more than ¾ full. Reposition dirt can using self-locating guide. Lower the bail arm to seal against gasket.

Changing Dirt Can Gasket

1. Peel off old gasket.

2. Clean old adhesive off gasket seat.

3. Check replacement gasket for fit; trim if necessary.

4. Coat gasket and seat with rubber cement, apply gasket.

5. Check for airtight seal after cement is dry.

Maintaining the Equalizing Line

If equipment is supplied with equalizing line, periodically check it for plugs or leaks.

CAUTION: Spencer disposable dirt can liners must always be used or mechanical and environmental damage may result.

Replacing the Target Plate

The target plate is designed to absorb impact and abrasion damage as it diverts solid litter into the dirt can. It may eventually wear out. To replace:

1. Remove dirt can.

2. Swing the target plate to a horizontal position and release it from its supporting hooks.

3. Install a new plate on hooks.

Tubular Bag SeparatorRead instructions before handling and starting equipment



Manufactured under the following Registered Trademarks: 62,801; 140,976;652,701; 134,026; 341,418; 1,348,270; 959,254; 7,218,205; 7,218,284


Serial No.

Model No.

Bag No.

4-5/16"w x 3-1/2"h

Tubular Bag SeparatorRead instructions before handling and starting equipment





Manufactured under the following Registered Trademarks: 62,801; 140,976;652,701; 134,026; 341,418; 1,348,270; 959,254; 7,218,205; 7,218,284


Serial No.

Model No.

Bag No.

4-5/16"w x 3-1/2"h

9

Possible Cause

INSUFFICIENT AIR THROUGHSySTEM

Corrective Action

Indication: low vacuum as determined by gauge measurement

• Incorrect rotation. Change motor leads to correct rotation.

• Incorrect reassembly of machine after customer Following instructions on pages 6-7, disassemble machine and repairs. reassemble correctly.

• Tubing too small, causing excessive friction loss. Increase tubing size or install machine providing higher vacuum.

• Too many operators using system at once. Restrict number of simultaneous operators or upgrade to larger Industravac V-Jet unit.

• Too much air entering system due to improper Use only Spencer tools, do not use open end hoses. tools or open end hoses being used.

• Machine running slow due to low motor voltage. Refer to motor manufacturer’s instructions, check voltage supply and connections.

• Machine air passages clogged with material. Disassemble, clean and inspect all parts, check filter bags for holes.

• Impellers worn due to abrasion or vibration. Replace impellers.

• Air gate (blast gate) closed. Refer to air gate instructions on page 6 and readjust.

Indication: machine design capacity too small for the system

• System requirements incorrectly calculated. Install larger Industravac V-Jet unit to handle system requirements.

• Too much leakage and/or openings. Eliminate all leakage; see separator troubleshooting section.

Possible Cause

• Worn or poorly fitting seals. Check access door and dirt can seals, reposition or replace if necessary.

• Holes worn in separator by abrasive materials. Check target plate, replace if worn; repair holes.

• Leaks. See above.

• Separator outlet blocked. Check dirt can, empty if more than 3/4 full. Make sure filter bags are not blocking separator outlet. Check outlet duct.

• Dirt can liner sucked up against filter bag inlet. Inspect equalizing line for holes and clean line to ensure proper

manifold suction under dirt can to keep liner in place.

• Machine rotating backward. Reverse motor leads.

• Filter bags clogged. Shake bags more frequently (only when system is shut down).

• Loose bag(s). Reinstall bags according to instructions on page 8.

• Holes in bags. Replace worn bags, eliminate cause if bags wear out prematurely (e.g., wrong filter bag material, dirt can not emptied often enough).

• Leaks. See Air Leaks, page 8.

• Incorrect filter bag material. Consult Spencer Service Dept. with information on material handled.

PROBLEM

PROBLEM

AIR LEAKS

LOWVACUUM/NO VACUUM

DIRTPASSING THROUGH SySTEM

Corrective Action

VI. Troubleshooting Guide - Separator

VI. Troubleshooting Guide - Vacuum Producer

10

Indication: external machine malfunction–bearing whining or growling

• Too much grease; motor bearings hot. Remove drain plug and let excess grease drain out.

• Too little grease; motor bearings dry. Grease per instructions of motor manufacturer.

• Bearing failure. Replace bearing.

• Bearing retainers worn. Replace bearing.

Indication: internal machine malfunction

• Impellers hitting after field reassembly and/or Disassemble and reassemble per instructions on pages 6-7, slipping on shaft due to heat. adjust shims as required. Bleed air at low flow to reduce heat.

• Impellers coming apart due to age. Replace impellers.

• Deflectors coming apart due to age. Repair or replace deflectors.

• Impellers and/or deflectors coming apart due to Too much material passing through separator. Replace wear from dirty air. impellers and/or deflectors. Check filter bags for holes. Check to be sure filter bag material is correct for debris collected.

• Machine operating in surge or unbalanced flow Increase air flow to stop surge condition. range.

• Machine unbalanced, running rough. Rebalance and/or clean machine, see further comments under Machine Vibrating.

• Foreign material in machine. Disassemble machine, inspect and clean. Check filter bags for holes to prevent further clogging.Indication: motor malfunction

• Abnormal hum or whine. Check motor manufacturer’s instructions, check voltage supply and connections.

• Wrong voltage (high voltage will burn out motor Check motor manufacturer’s instructions, check voltage supply and cause noticeable noise). and connections.

• Bearing noise. See External Machine Malfunction.

• Motor rebuilt improperly, thrust taken on wrong end. Rebuild motor properly and correct the end play.

• Loose part in motor. Tighten, repair or replace. (Check with motor manufacturer.)

• Low frequency. Separate power supply, correct frequency.

• Material buildup on impellers. Clean impellers, check filter bags for holes.

• Shaft bent (.001” max. runout per 10” of length). Straighten shaft.

• Bearing failure. Replace bearing(s).

• Faulty replacement motor installed. Replace with correct motor.

• Motor imbalance. Disassemble machine, balance motor.

• Machine reassembled incorrectly. Disassemble machine, reassemble following instructions on pages 6-7.

• Improper motor voltage causing operation at Check voltage and wiring connections, correct voltage. incorrect speed.

• Liquids passing through machine. Do not use Industravac V-Jet unit for liquid pickup. (Contact Spencer representative for mobile wet separator.)

• Material passing through vacuum producer. Disassemble, clean and inspect all parts, check filter bags for holes.

• Machine operating in surge or unbalanced Increase air flow to stop surge condition. flow range.

• Machine not mounted on solid foundation Reinforce the foundation. (e.g., on unstable catwalk).

(Check with putty and thermometer; consult Spencer Service Dept. for assistance.)

• Ambient temperature too high for insulation class. Cool motor or replace with motor having proper insulation.

• Incorrect voltage. Change to correct voltage.

• Incorrect cycle. Change to correct cycle.

• Electrical short-circuit; insulation failure. Repair or replace motor.

• Motor overloaded. Upgrade to larger Industravac V-Jet unit, or reduce amount of air in vacuum producer. Verify amperage of motor. Set air gate.

• Leaks in system. Check components and tubing system for leaks.

• Unbalanced voltage supply. Consult power company for correction.

Possible CausePROBLEM

MACHINE NOISy

Corrective Action

MOTORHOT

MACHINE VIBRATING

11

Date

Part No.

Filter Bag Part No. Filter Bag Material Date Changed

Description

Filter Bag Maintenance Record

Vacuum Accessories Record (Hoses, Tools, Valves)

Spencer Products and Services

Industrially rated products offering effective solutions for air and gas handling applications:

• Modular central vacuum systems• Mobile or stationary integrated vacuum units• Dust collectors and separators• Multistage centrifugal blowers• Single-stage centrifugal blowers• Regenerative blowers• Gas boosters• Custom-engineered products with special materials

for extreme temperatures and pressures

Complementary accessories with singlesource convenience and compatibility:

• Standard and custom electrical control panels – UL, CUL Listed and C.E. Compliant available

• Comprehensive selection of tubing, fittings, vacuum hoses, valves and tools

• Valves, gauges, couplings, shrink sleeves, vibration isolators and other system components

Comprehensive engineering and other customer support services:

• The industry’s largest complement of technical specialists in air and gas technology

• Global parts and service organization• Application research and testing facility

Global organization of sales representatives and distributors offering:

• Product selection, installation and operation assistance

• Comprehensive system design services• Follow-up services and troubleshooting

For the name and telephone number of yourlocal Spencer representative, call 800-232-4321 or email [email protected].

Blowers & Vacuum Systems with an Engineering Edge

TEL 800-232-4321 ◆ 860-688-8361 ◆ FAX 860-688-0098 ◆ www.spencerturbine.com

The Turbine Company, 600 Day Hill Road, Windsor, CT 06095 USA

Spencer Corporate Headquarters and Manufacturing, Windsor, Connecticut, USA

Industravac® is a registered trademark of The Spencer Turbine Company.

Form IVJ Copyright ©2013 The Spencer Turbine Company 040313KBA



Documents

TM Vacuum Cleaning System - Spencer Turbine