-
MAKING MODERN LIVING POSSIBLE
Technical Information
Orbital MotorTMTHW
powersolutions.danfoss.com
http://powersolutions.danfoss.com
-
Revision history Table of revisions
Date Changed Rev
November 2015 Code number corrected 0101
April 2015 Converted to Danfoss layout BA
August 2013 First version AA
Technical Information TMTHW Orbital Motors
2 L1327341 en-US • Rev 0101 • November 2015
-
A wide range of Orbital MotorsCharacteristic, features and
application areas of Orbital
Motors....................................................................................4
Characteristic features of Danfoss Orbital
Motors..........................................................................................................
4Technical features of Danfoss Orbital
Motor.....................................................................................................................4The
Danfoss Orbital Motors are used in the following application
areas:..............................................................5
Survey of literature with technical data on Danfoss Orbital
Motors..............................................................................5
Introduction the Orbital Motor SeriesT-Series – The Highest
Torque.....................................................................................................................................................
6O-Series – The Flexible
Choice.....................................................................................................................................................6V-Series
– The Core
Solution........................................................................................................................................................
6TMTHW
features................................................................................................................................................................................6
Speed, torque and outputTMTHW speed, torque and
output............................................................................................................................................
7
Versions and code numbersTMTHW version and code
numbers..........................................................................................................................................
8
Technical dataTechnical data for
TMTHW............................................................................................................................................................
9Maximum permissible shaft seal
pressure..............................................................................................................................
9Pressure drop in
motor................................................................................................................................................................
10Direction of shaft
...........................................................................................................................................................................11Permissible
shaft load for
TMTHW...........................................................................................................................................11
Function diagramsTMTHW
315......................................................................................................................................................................................12TMTHW
400......................................................................................................................................................................................13TMTHW
500......................................................................................................................................................................................13TMTHW
630......................................................................................................................................................................................14TMTHW
800......................................................................................................................................................................................14
Technical dataPort thread
versions......................................................................................................................................................................15Manifold............................................................................................................................................................................................
15
DimensionsWheel flange-spigot diameter Ø 180 mm - BC Ø 210
mm..............................................................................................16Wheel
flange-spigot diameter Ø 223.9 mm - BC Ø 265
mm..........................................................................................
17
Technical Information TMTHW Orbital Motors
Contents
L1327341 en-US • Rev 0101 • November 2015 3
-
Characteristic, features and application areas of Orbital
Motors
Danfoss is a world leader within production of low speed orbital
motors with high torque. We can offermore than 3,000 different
orbital motors, categorised in types, variants and sizes (including
different shaftversions).
The motors vary in size (rated displacement) from 8 cm³ [0.50
in³] to 800 cm³ [48.9 in³] per revolution.
Speeds range up to approximate 2,500 min-1 (rpm) for the
smallest type and up to approximate 600 min-1
(rpm) for the largest type.
Maximum operating torques vary from 13 N•m [115 lbf•in] to 2,700
N•m [24,000 lbf•in] (peak) andmaximum outputs are from 2.0 kW [2.7
hp] to 70 kW [95 hp].
Characteristic features of Danfoss Orbital Motors
• Smooth running over the entire speed range• Constant operating
torque over a wide speed range• High starting torque• High return
pressure without the use of drain line (High pressure shaft seal)•
High efficiency• Long life under extreme operating conditions•
Robust and compact design• High radial and axial bearing capacity•
For applications in both open and closed loop hydraulic systems•
Suitable for a wide variety of hydraulics fluids
Technical features of Danfoss Orbital Motor
The programme is characterised by technical features appealing
to a large number of applications and apart of the programme is
characterised by motors that can be adapted to a given application.
Adaptionscomprise the following variants among others:
Technical Information TMTHW Orbital Motors
A wide range of Orbital Motors
4 L1327341 en-US • Rev 0101 • November 2015
-
• Motors with corrosion resistant parts• Wheel motors with
recessed mounting flange• OMP, OMR- motors with needle bearing• OMR
motor in low leakage version• OMR motors in a super low leakage
version• Short motors without bearings• Ultra short motors• Motors
with integrated positive holding brake• Motors with integrated
negative holding brake• Motors with integrated flushing valve•
Motors with speed sensor• Motors with tacho connection• All motors
are available with black finish paint
The Danfoss Orbital Motors are used in the following application
areas:
• Construction equipment• Agricultural equipment• Material
handling & Lifting equipment• Forestry equipment• Lawn and turf
equipment• Special purpose• Machine tools and stationary equipment•
Marine equipment
Survey of literature with technical data on Danfoss Orbital
Motors
Detailed data on all Danfoss Orbital Motors can be found in our
motor catalogue, which is divided intomore individual
subcatalogues:• General information on Danfoss Orbital Motors:
function, use, selection of orbital motor, hydraulic
systems, etc.• Technical data on small motors: OML and OMM•
Technical data on medium sized motors: OMP, OMR, OMH• Technical
data on medium sized motors: DH and DS• Technical data on medium
sized motors: OMEW• Technical data on medium sized motors: VMP•
Technical data on medium sized motors: VMR• Technical data on large
motors: OMS, OMT and OMV• Technical data on large motors: TMK•
Technical data on large motors: TMT• Technical data on large
motors: TMTHW• Technical data on large motors: TMVW
A general survey brochure on Danfoss Orbital Motors gives a
quick motor reference based on power,torque, speed and
capabilities.
Technical Information TMTHW Orbital Motors
A wide range of Orbital Motors
L1327341 en-US • Rev 0101 • November 2015 5
-
By introducing the TMTHW, Danfoss is introducing the first
Orbital Motor of a new Series. In order to meetthe demands for
motors that have the right duty cycle and efficiency capabilities
for a given function.Danfoss now has 3 Orbital Motor Series:
T-Series – The Highest Torque
Leading performance with a long lifetime makes light work of the
heaviest duties. Offering pressurecapability up to 350 bar [5076
psi] and high starting torque, the T-Series is the energy-efficient
choice forthe toughest working environments.
O-Series – The Flexible Choice
The O-Series is flexible beyond compare. Delivering premium
power across the board, these motorscover small to large, medium to
heavy-duty needs with pressure capability up to 275 bar [3990
psi].Robust, reliable and designed to fulfill the latest emissions
standards.
V-Series – The Core Solution
The V-Series is your quality benchmark in the medium duty
market. Based on proven technology, thesereliable motors will
reduce your overall system costs while adding value to your
machine. Perfect formany tasks.
TMTHW features
• Robust bearing design• Not sensitive towards return pressure•
Extra patented sealing design• High pressure rating• Excellent
performance / weight• Designed based on decades of experience with
orbital motor-technology
Technical Information TMTHW Orbital Motors
Introduction the Orbital Motor Series
6 L1327341 en-US • Rev 0101 • November 2015
-
The following bar diagrams, are useful for a quick selection of
relevant motor size for the application. Thefinal motor size can be
determined by using the Function diagrams on page 12.
The function diagrams are based on actual tests on a
representative number of motors from ourproduction. The diagrams
apply to a return pressure between 5 and 10 bar [75 and 150 psi]
when usingmineral based hydraulic oil with a viscosity of 35 mm2/s
[165 SUS] and a temperature of 50°C [120°F]. Forfurther explanation
concerning how to read and use the function diagrams, please
consult the paragraph"Selection of motor size" in the technical
information "General" 520L0232.
TMTHW speed, torque and output
The bar diagrams shown are useful for a quick selection of
relevant motor size for the application.1. Intermittend values2.
Continuous values
Maximum speed
P301 810
1
2
min-1(rpm)
0
100
200
300
400
500
600
315 400 500 630 800
Maximum torque
P301 811
1
2
lbf•in Nm
35 000
30 000
25 000
20 000
15 000
10 000
5 000
0 0
500
1000
1500
2000
2500
3000
3500
4000
315 400 500 630 800
Maximum output
P301 812
1
2
hp kW
90
80
70
60
50
40
30
20
10
0 0
10
20
30
40
50
60
70
315 400 500 630 800
Technical Information TMTHW Orbital Motors
Speed, torque and output
L1327341 en-US • Rev 0101 • November 2015 7
-
TMTHW version and code numbers
TMTHW standard motor
Mounting flange: Wheel
Spigotdiamer
Ø180 mm [7.09 in]
Bolt circlediameter
Ø210 mm [8.27 in]
Shaft Port size Port Style Drain Portsize
Standardshaft seal
Metricversion
Paintedblack
Check valve Main typedesignation
Conf. code
Thread holeFl.
G 3/4 Side port G 1/4 X X X No TMTHW A1
Code numbers TMTHW wheel flange
Conf. code Displacement
315 400 500 630 800
A1 11137330 11137331 11137342 11053388 11125392
Mounting flange: Wheel
Spigotdiamer
Ø224 mm [8.82 in]
Bolt circlediameter
Ø265 mm [10.4 in]
Shaft Port size Port Style Drain portsize
Standardshaft seal
Metricversion
Paintedblack
Check valve Main typedesignation
Conf. code
Thread holeFl.
G 3/4 Side port G 1/4 X X X No TMTHW B1
Code numbers TMTHW wheel flange
Conf. code Displacement
315 400 500 630 800
B1 - 11089435 11089438 11089439 11089440
Technical Information TMTHW Orbital Motors
Versions and code numbers
8 L1327341 en-US • Rev 0101 • November 2015
-
Technical data for TMTHW
Type TMTHW TMTHW TMTHW TMTHW TMTHW
Motor size 315 400 500 630 800
Geometricdisplacement
cm3
[in3]314.9[19.2]
393.1[24.0]
495[32.2]
630.7[38.5]
802.2[49.0]
Maximum speed min-1
[rpm]cont. 490 450 400 315 240
int.1) 580 590 480 370 290
Maximum torque N•m[lbf•in]
cont. 1300[11 500]
1690[14 960]
2200[19 470]
2510[22 215]
2650[23 450]
int.1) 1510[13 365]
1950[17 260]
2550[22 570]
3220[28 500]
3510[31 065]
Maximumoutput
kW[hp]
cont. 50 [67] 55 [74] 55 [74] 50 [67] 50 [67]
int.1) 55 [74] 60 [80] 65 [87] 60 [80] 60 [80]
Maximumpressure drop
bar[psi]
cont. 300 [4350] 300 [4350] 300 [4350] 275 [3990] 225 [3260]
int.1) 350 [5075] 350 [5075] 350 [5075] 350 [5075] 300
[4350]
Maximum oilflow
l/min[US gal/min]
cont. 150 [39.6] 180 [47.6] 200 [52.8] 200 [52.8] 200 [52.8]
int.1) 180 [47.6] 240 [63.4] 240 [63.4] 240 [63.4] 240
[63.4]
Max. startingpressure withunloaded shaft
bar[psi]
6 [87] 6 [87] 6 [87] 6 [87] 5 [72]
Minimumstarting torque
N•m[lbf•in]
at max. press.drop cont.:
910[8055]
1185[10490]
1540[13630]
1730[15310]
1855[16420]
at max. press.drop int.1):
1060[9380]
1365[12080]
1785[15800]
2255[19960]
2460[21770]
1) Intermittent operation: the permissible values may occur for
max. 10% of every minute
Type Maximum inlet pressure Maximum return pressurewith drain
line
TMTHW 315-800 bar[psi]
Cont. 300 [4350] 140 [2031]
Int.1) 380 [5510] 175 [2538]1) Intermittend operation: the
permissible values may occur for max. 10% of every minute
Oil flow in drain line
The table below shows the maximum oil flow in the drain line at
a return pressure less than 5-10 bar[75-150 psi].
Pressure drop Viscosity Oil flow in drain line
bar [psi] mm2/s [SUS] l/min [US gal/min]
200 [2900] 20 [100] 2.5 [0.66]
35 [165] 1.5 [0.4]
275 [3990] 20 [100] 4.0 [1.1]
35 [165] 2.5 [0.66]
Maximum permissible shaft seal pressure
TMTHW with standard shaft seal and drain connection. The
pressure on shaft seal equals the pressure inthe drain line.
Technical Information TMTHW Orbital Motors
Technical data
L1327341 en-US • Rev 0101 • November 2015 9
-
151-1673.10
0 100 200 300 400 500 600 max.
1500
1200
900
600
300
0
100
90
80
70
60
50
40
30
20
10
0
psi bar
P P
min-1(rpm)
- - - - Intermittent operation: The permissible values may occur
for maximum 10% of every minute.
____ Continuous operation
Drain line should always be used.
Pressure drop in motor
45
40
35
30
25
20
15
10
5
0
250 50 75 100 125 150 175 200
TMTHW Pressure drop in motor
l/min
US gal/min
P301 556
Q
12
Q
psi bar
∆p ∆p
650600550500450400350300250200150100
500
0 5 10 15 20 25 30 35 40 45 50
The curve applies to an unloaded motor shaft and an oil
viscosity of 35 mm2/s [165 SUS].1. TMTHW 3152. TMTHW 400, 500, 630
and 800
Technical Information TMTHW Orbital Motors
Technical data
10 L1327341 en-US • Rev 0101 • November 2015
-
Direction of shaft
Permissible shaft load for TMTHW
0
20 000
40 000
60 000
80 000
100 000
120 000
140 000
-20 -10 0 10 20 30 40 50 60 70 80 90 100 110 120
- 0 +
30 000
24 000
18 000
12 000
6 000
0
Prad.[lbf ]
Prad.N
P301 559
mm
[in]-1.0 -0.5 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0
Permissible radial shaft load
The output shaft runs in tapered roller bearings that permit
high axial and radial forces.
The permissible radial load on the shaft is shown for an axial
load of 0 N as a function of the distance fromthe mounting flange
to the point of load application.
The curve is based on B10 Bearing life (2000 hours or 12 000 000
shaft revolutions at 100 min 1) at ratedoutput torque, when
mineral-based hydraulic oil with a sufficient content of anti-wear
additives, is used.
Technical Information TMTHW Orbital Motors
Technical data
L1327341 en-US • Rev 0101 • November 2015 11
-
Explanation of function diagram use, basis and conditions can be
found under Speed and torque Speedand torque
[blue] Continuous range
[pink] Intermittent range (max. 10% operation every minute)
Intermittent pressure drop and oil flow must not occur
simultaneously.
TMTHW 315
0
250
500
750
1000
1250
1500
1750
0
5 000
10 000
15 000
VMP 50lbf• in Nm
0 50 100 150 200 250 300 350 400 450 500 550 600
P301 551
min-1(rpm)
100
l/min
[26.
4 U
S ga
l/min
]
125
l/min
[33.
0 U
S ga
l/min
]
150
l/min
[39.
6 U
S ga
l/min
]
180
l/min
[47.
6 U
S ga
l/min
]
Q =
10
l/min
[2.6
US
gal/m
in]
20 l/
min
[5.3
US
gal/m
in]
40 l/
min
[10.
6 U
S ga
l/min
]
60 l/
min
[15.
9 U
S ga
l/min
]
80 l/
min
[21.
1 U
S ga
l/min
]
325 bar[4713 psi]300 bar
[4351 psi]
250 bar[3625 psi]
275 bar[3988 psi]
225 bar[3263 psi]200 bar
[2900 psi]
120 bar[1740 psi]
160 bar[2320 psi]
80 bar[1160 psi]
∆ p= 350 bar[5076 psi]
75%
20kW30kW
40kW
50kW60kW 75kW
η t =80%η t =60%70%
N=2.5kW 10kW5kW
40 bar[580 psi]
Technical Information TMTHW Orbital Motors
Function diagrams
12 L1327341 en-US • Rev 0101 • November 2015
-
TMTHW 400
0
250
500
750
1000
1250
1500
1750
2000
2250
0
2 000
4 000
6 000
8 000
10 000
12 000
14 000
16 000
18 000
VMP 50lbf• in Nm
0 50 100 150 200 250 300 350 400 450 500 550 600
P301 552
min-1(rpm)
100
l/min
[26.
4 U
S ga
l/min
]
125
l/min
[33.
0 U
S ga
l/min
]
150
l/min
[39.
6 U
S ga
l/min
]
180
l/min
[47.
6 U
S ga
l/min
]
Q =
10
l/min
[2.6
US
gal/m
in]
20 l/
min
[5.3
US
gal/m
in]
40 l/
min
[10.
6 U
S ga
l/min
]
60 l/
min
[15.
9 U
S ga
l/min
]
80 l/
min
[21.
1 U
S ga
l/min
]
325 bar[4713 psi]300 bar
[4351 psi]
250 bar[3625 psi]
275 bar[3988 psi]
225 bar[3263 psi]200 bar
[2900 psi]
120 bar[1740 psi]
160 bar[2320 psi]
80 bar[1160 psi]
75%
20kW 30kW40kW 50kW 60kW
80%η t =81%η t =60%70%
N=2.5kW 10kW5kW
240
l/min
[63.
4 U
S ga
l/min
]
40 bar[580 psi]
∆ p= 350 bar[5076 psi]
TMTHW 500
00
250
500
750
1000
1250
1500
1750
2000
2250
2500
2750
0
5 000
10 000
15 000
20 000
VMP 50lbf• in Nm
0 50 100 150 200 250 300 350 400 450 500
P301 553
min-1(rpm)
100
l/min
[26.
4 U
S ga
l/min
]
125
l/min
[33.
0 U
S ga
l/min
]
150
l/min
[39.
6 U
S ga
l/min
]
200
l/min
[52.
8 U
S ga
l/min
]
Q =
10
l/min
[2.6
US
gal/m
in]
20 l/
min
[5.3
US
gal/m
in]
40 l/
min
[10.
6 U
S ga
l/min
]
60 l/
min
[15.
9 U
S ga
l/min
]
80 l/
min
[21.
1 U
S ga
l/min
]
325 bar[4713 psi]300 bar
[4351 psi]
250 bar[3625 psi]
275 bar[3988 psi]
225 bar[3263 psi]200 bar
[2900 psi]
120 bar[1740 psi]
160 bar[2320 psi]
80 bar[1160 psi]
80%
20kW30kW
40kW
50kW60kW
81%η t =83% η t =60%70%75%
N=2.5kW10kW
5kW
240
l/min
[63.
4 U
S ga
l/min
]
180
l/min
[47.
6 U
S ga
l/min
]
40 bar[580 psi]
∆ p= 350 bar[5076 psi]
Technical Information TMTHW Orbital Motors
Function diagrams
L1327341 en-US • Rev 0101 • November 2015 13
-
TMTHW 630
0
250
500
750
1000
1250
1500
1750
2000
2250
2500
2750
3000
3250
3500
0
5 000
10 000
15 000
20 000
25 000
30 000
VMP 50lbf• in Nm
0 50 100 150 200 250 300 350 400
P301 554
min-1(rpm)
100
l/min
[26.
4 U
S ga
l/min
]
125
l/min
[33.
0 U
S ga
l/min
]
150
l/min
[39.
6 U
S ga
l/min
]
200
l/min
[52.
8 U
S ga
l/min
]
Q =
10
l/min
[2.6
US
gal/m
in]
20 l/
min
[5.3
US
gal/m
in]
40 l/
min
[10.
6 U
S ga
l/min
]
60 l/
min
[15.
9 U
S ga
l/min
]
80 l/
min
[21.
1 U
S ga
l/min
]
325 bar[4713 psi]300 bar
[4351 psi]
250 bar[3625 psi]
275 bar[3988 psi]
225 bar[3263 psi]200 bar
[2900 psi]
120 bar[1740 psi]
160 bar[2320 psi]
80 bar[1160 psi]
80%
20kW
30kW
40kW
50kW
60kW
81%
η t =83% η t =60%70%
75%
N=2.5kW
10kW
5kW
240
l/min
[63.
4 U
S ga
l/min
]
180
l/min
[47.
6 U
S ga
l/min
]
40 bar[580 psi]
∆ p= 350 bar[5076 psi]
TMTHW 800
0
250
500
750
1000
1250
1500
1750
2000
2250
2500
2750
3000
3250
3500
3750
4000
0
5 000
10 000
15 000
20 000
25 000
30 000
35 000
VMP 50lbf• in Nm
0 50 100 150 200 250 300
P301 555
min-1(rpm)
100
l/min
[26.
4 U
S ga
l/min
]
125
l/min
[33.
0 U
S ga
l/min
]
150
l/min
[39.
6 U
S ga
l/min
]
200
l/min
[52.
8 U
S ga
l/min
]
20 l/
min
[5.3
US
gal/m
in]
40 l/
min
[10.
6 U
S ga
l/min
]
60 l/
min
[15.
9 U
S ga
l/min
]
80 l/
min
[21.
1 U
S ga
l/min
]
250 bar[3625 psi]
275 bar[3988 psi]
225 bar[3263 psi]200 bar
[2900 psi]
120 bar[1740 psi]
160 bar[2320 psi]
80 bar[1160 psi]
80%
20kW
30kW
40kW
50kW
60kW
81%
83%η t =85%
η t =60%70%75%
N=2.5kW
10kW
5kW
240
l/min
[63.
4 U
S ga
l/min
]
180
l/min
[47.
6 U
S ga
l/min
]
40 bar[580 psi]
∆ p= 300 bar[4351 psi]
10 l/
min
[2.6
US
gal/m
in]
Technical Information TMTHW Orbital Motors
Function diagrams
14 L1327341 en-US • Rev 0101 • November 2015
-
Port thread versions
A
E
P301 561_AE
min
. 18
[0.7
1]
A: G Main port
E: ISO 228/1 – G 3/4
C
G
P301 561_CG
min
. 12
[0.4
7]
C: G Drain port
G: ISO 228/1 – G 1/4
Manifold
L3
15.6[0.64] 15.6[0.64]
15.6[0.64] 15.6[0.64]
14.5[0.57]
7.25[0.29] 11.0[0.43]
19.6
[0.7
7]19
.6[0
.77]
42[1
.65]
42[1
.65]
P301 566
L3: Dimentional for given TMTHW-motor see: Dimensions on page
16.
Technical Information TMTHW Orbital Motors
Technical data
L1327341 en-US • Rev 0101 • November 2015 15
-
Wheel flange-spigot diameter Ø 180 mm - BC Ø 210 mm
5x 72°
Ø140[5.51]
10x Ø14.2[0.56]
max
242
.4[9
.54]
max 195.4[7.69]
15°15°
Ø210
[8.27
]
15°15°
Ø172[6.77]
Ø92.7[3.65]Ø92.9[3.66]
max 146[5.75]Ø180.0 [7.09]Ø179.8 [7.08]
7[0.
28]
12[0
.47]
11.7
[0.4
6]
18[0
.71]
7.2[
0.28
]
124.
15[4
.888
]
84[3.31]
L max L 1
L 2L 3
F
C
DE
P301 565
Not
pai
nted
Not
pai
nted
C: G 3/4; 17 mm [0.66 in] deep
D: Drain connection G 1/4; 12 mm [0.47 in] deep
E: M10; 17 mm [0.66 in] deep
F: M14 × 1.5
Size 315-800 cm3
Weight 34-38 kg
Output shaft F180/5xM14 BC ø140/PD.ø92.8
Mounting flange Wheel 10x ø14 BC ø210/PD ø180
Technical Information TMTHW Orbital Motors
Dimensions
16 L1327341 en-US • Rev 0101 • November 2015
-
TMTHW dimensions
Size315-800 cm3
LMAX L1 L2 L3 Weight
mm [in] mm [in] mm [in] mm [in] kg [lb]
TMTHW 315 135.1 [5.33] 117.1 [4.61] 106.1 [4.18] 91.6 [3.61]
33.7 [74.30]
TMTHW 400 143.3 [5.64] 125.1 [4.93] 114.1 [4.49] 99.6 [3.92]
34.8 [76.72]
TMTHW 500 153.8 [6.06] 135.6 [5.34] 124.6 [4.91] 110.1 [4.33]
35.7 [78.70]
TMTHW 630 167.8 [6.61] 149.6 [5.89] 138.6 [5.46] 124.1 [4.89]
37.2 [82.01]
TMTHW 800 167.8 [6.61] 149.6 [5.89] 138.6 [5.46] 124.1 [4.89]
37.2 [82.01]
Wheel flange-spigot diameter Ø 223.9 mm - BC Ø 265 mm
C
F
E D
Not
pai
nted
Not
pai
nted
Ø265.0[10.43]
8xØ17.6[0.69]
max
310
.3[9
.54]
5.0[
0.20
]
23.0
[0.9
1]
5.0[
0.20
]
max 146[5.75]
Ø223.8[8.81]Ø224.0[8.82]
Ø200[7.87]Ø129.7[5.16]Ø129.9[5.11]
138.
7[5.
46]
16[0
.63]
6[0.
24]
20°20°20°
ø170
.0[6
.69]
84[3.31]
max 238.0[9.37]
L max L 1L 2 L
3
6x60°
Technical Information TMTHW Orbital Motors
Dimensions
L1327341 en-US • Rev 0101 • November 2015 17
-
C: G 3/4; 17 mm [0.66 in] deep
D: Drain connection G 1/4; 12 mm [0.47 in] deep
E: M10; 17 mm [0.66 in] deep
F: M16 × 1.5
Size 400-800 cm3
Weight 42.1-44.5 kg
Output shaft F200/6xM16 BC ø170/PD.ø130
Mounting flange Wheel 8x ø17.5 BC ø265/PD ø224
TMTHW dimensions
Size400-800 cm3
LMAX L1 L2 L3 Weight
mm [in] mm [in] mm [in] mm [in] kg [lb]
TMTHW 400 139 [5.47] 120.8 [4.76] 109.8 [4.32] 95.3 [3.75] 42.1
[92.81]
TMTHW 500 147.6 [5.81] 129.4 [5.09] 118.4 [4.66] 103.9 [4.09]
43.0 [94.80]
TMTHW 630 161.6 [6.36] 143.4 [5.65] 132.4 [5.21] 117.9 [4.64]
44.5 [98.11]
TMTHW 800 161.6 [6.36] 143.4 [5.65] 132.4 [5.21] 117.9 [4.64]
44.5 [98.11]
Technical Information TMTHW Orbital Motors
Dimensions
18 L1327341 en-US • Rev 0101 • November 2015
-
Technical Information TMTHW Orbital Motors
L1327341 en-US • Rev 0101 • November 2015 19
-
Danfoss Power Solutions is a global manufacturer and supplier of
high-quality hydraulic andelectronic components. We specialize in
providing state-of-the-art technology and solutionsthat excel in
the harsh operating conditions of the mobile off-highway market.
Building onour extensive applications expertise, we work closely
with our customers to ensureexceptional performance for a broad
range of off-highway vehicles.
We help OEMs around the world speed up system development,
reduce costs and bringvehicles to market faster.
Danfoss – Your Strongest Partner in Mobile Hydraulics.
Go to www.powersolutions.danfoss.com for further product
information.
Wherever off-highway vehicles are at work, so is Danfoss. We
offer expert worldwide supportfor our customers, ensuring the best
possible solutions for outstanding performance. Andwith an
extensive network of Global Service Partners, we also provide
comprehensive globalservice for all of our components.
Please contact the Danfoss Power Solution representative nearest
you.
Local address:
Danfoss Power Solutions GmbH & Co. OHGKrokamp 35D-24539
Neumünster, GermanyPhone: +49 4321 871 0
Danfoss Power Solutions ApSNordborgvej 81DK-6430 Nordborg,
DenmarkPhone: +45 7488 2222
Danfoss Power Solutions (US) Company2800 East 13th StreetAmes,
IA 50010, USAPhone: +1 515 239 6000
Danfoss Power Solutions Trading(Shanghai) Co., Ltd.Building #22,
No. 1000 Jin Hai RdJin Qiao, Pudong New DistrictShanghai, China
201206Phone: +86 21 3418 5200
Danfoss can accept no responsibility for possible errors in
catalogues, brochures and other printed material. Danfoss reserves
the right to alter its products without notice. This also applies
toproducts already on order provided that such alterations can be
made without changes being necessary in specifications already
agreed.All trademarks in this material are property of the
respective companies. Danfoss and the Danfoss logotype are
trademarks of Danfoss A/S. All rights reserved.
L1327341 en-US • Rev 0101 • November 2015 www.danfoss.com ©
Danfoss A/S, 2015
Products we offer:
• Bent Axis Motors• Closed Circuit Axial Piston
Pumps and Motors• Displays• Electrohydraulic Power
Steering• Electrohydraulics• Hydraulic Power Steering•
Integrated Systems• Joysticks and Control
Handles• Microcontrollers and
Software• Open Circuit Axial Piston
Pumps• Orbital Motors• PLUS+1® GUIDE• Proportional Valves•
Sensors• Steering• Transit Mixer Drives
Comatrolwww.comatrol.com
Schwarzmüller-Inverterwww.schwarzmueller-inverter.com
Turolla www.turollaocg.com
Hydro-Gearwww.hydro-gear.com
Daikin-Sauer-Danfosswww.daikin-sauer-danfoss.com
ContentsA wide range of Orbital MotorsCharacteristic, features
and application areas of Orbital MotorsCharacteristic features of
Danfoss Orbital MotorsTechnical features of Danfoss Orbital
MotorThe Danfoss Orbital Motors are used in the following
application areas:
Survey of literature with technical data on Danfoss Orbital
Motors
Introduction the Orbital Motor SeriesT-Series – The Highest
TorqueO-Series – The Flexible ChoiceV-Series – The Core
SolutionTMTHW features
Speed, torque and outputTMTHW speed, torque and output
Versions and code numbersTMTHW version and code numbers
Technical dataTechnical data for TMTHWMaximum permissible shaft
seal pressurePressure drop in motorDirection of shaftPermissible
shaft load for TMTHW
Function diagramsTMTHW 315TMTHW 400TMTHW 500TMTHW 630TMTHW
800
Technical dataPort thread versionsManifold
DimensionsWheel flange-spigot diameter Ø 180 mm - BC Ø 210
mmWheel flange-spigot diameter Ø 223.9 mm - BC Ø 265 mm
![TMTHW Orbital Motor - Danfossfiles.danfoss.com/documents/tmthw orbital motor technical... · Technical features of Danfoss Orbital Motor ... • Machine tools and ... [4350] 300 [4350]](https://img.pdfslide.net/doc/110x75/5b6544ae7f8b9a851e8b8a3e/tmthw-orbital-motor-orbital-motor-technical-technical-features-of-danfoss.jpg)
