Upload
hakhue
View
226
Download
4
Embed Size (px)
Citation preview
Vehicle's without Keyless EntryItem # Quantity Reqd Description1 9 Red T-Taps2 1 HP Switch - (Blade Style)3 1 2-1/4” x 2-1/4” Foam Pad4 8 8" Cable Ties5 1 4 Pin Molex Connector6 3 Blue T-Taps7 1 Hex Nut8 1 Flat Washer (Black)
P/N Qty Description00016-79200-01 1 Control Module00016-30960-02 1 Shock Sensor Module00016-12930-01 1 Main Installation Harness00016-60901-02 1 Hardware Bag00016-30960-03 2 Window Warning Decal00016-30960-04 1 Owner's Card00016-60901-04 1 Pin Switch00016-30960-29 1 Shock Sensor Harness00016-30960-05 1 LED00016-12930-01 2 Transmitters00016-12930-03 1 Headlight Extension Wire
Item # Quantity Reqd Description1 1 Security Module2 1 Shock Sensor3 1 LED Valet Switch4 1 HP Switch Ext.5 2 Window Decals6 1 Shock Sensor Ext. Wire 12”7 1 Main Harness8 1 Hardware Bag9 1 Owner's Manual10 2 25" Cable Ties11 2 Transmitters12 1 Headlight Extension Wire
Phillip screwdriver Straight-Slot screwdriverRatchet w/extension 10 mm socketDiagonal wire cutters Common pliersFlashlight Nylon trim tool7/16” Comb. wrench 5/16" drill bit and drill motorTorque Wrench 36in. lbs.
Kit Contents
Hardware Bag Contents
ConflictsNote: NOT FOR INSTALLATION ON VEHICLES WITHFACTORY THEFT DETERRENT SYSTEMS.
Item # Quantity Reqd Description
General ApplicabilityLegend
Additional Items Required For Installation
Recommended Tools SPECIAL NOTE: Installation Sequences
After TMS and Safety mandated preparatory steps have been taken,the installation sequence is the suggested method for completing theaccessory installation. In some instances the suggested sequence iswritten for one associate to install and in others the sequence is givenas part of a team accessory installation. Unless otherwise stated inthe document, the associates may perform the installation steps inany order to make the installation as efficient as possible whilemaintaining consistent quality.
Safety Tools
Special Tools
INSTALLATION TOOLS
Special Chemicals
Vehicle Service Parts (may be required for reassembly)
Toyota Corolla 2009 - Keyless Security AlarmPart Number: 00016-12935AccessoryCode: QK1
Southeast Distributors, LLC Page 1 of 17
INSTALLATION PREPARATION
Before starting installation
1. Familiarize yourself with the installation instructions.2. Inspect kit components.
VEHICLE PREPARATION
1. Place protective coverings on vehicle.
2. Disconnect negative battery clamp
Page 2 of 17
Negative BatteryCable
3. Remove the driver's side scuff plate.Inserting a plastic panel tool under thescuff plate and prying upward todisengage the snap clips.
4. Remove the driver side kick panel byinserting a plastic panel tool under the kickpanel and carefully pry to disengage thesnap clips.
TOYOTA COROLLA KEYLESS SECURITY ALARM
Southeast Distributors, LLC
Optional Step:
Insert a plastic tool under the front of the stuffplate and driver side kick panel, lift only that area.
Verify that the vehicle shorting pin is installed prior to installation.
Page 3 of 17
5. Remove (2), screws from thedriver's lower finish panel (right side). Pullthe lower finish panel outward from thevehicle dash to disengage the snap clips.
7. Carefully seperate the lower steeringcolumn cover halfs by disengaging the (4)tabs and remove cover.
6. Pull the lower finish panel (left side)outward from the vehicle dash todisengage the snap clips.
TOYOTA COROLLA KEYLESS SECURITY ALARM
Southeast Distributors, LLC
MOUNTING THE LED/VALET SWITCH:1. Carefully drill a 5 / 16 " diameter holein the center knock out of the left sidelower dash finish panel.
2. Remove the knurled mounting nut fromthe back of the switch, pass the wiresthrough the hole, then secure the switchwith the knurled nut.
MODULE PREPARATION
1. Secure the antenna to the back sideof the module, using a supplied foampad.
2. Route the antenna and secure to themain harness with (2) cable ties.
Foam PadCable Ties
"IMPORTANT........Failure to route the antenna cable as described will reslut in re-duced range of the system.
TOYOTA COROLLA KEYLESS SECURITY ALARM
Page 4 of 17
IMPORTANT ! If trim bezel is supplied,remove the center knock out and installthe provided new trim bezel.
INSTALLING PROCEDURES
Southeast Distributors, LLC
Page 5 of 17
INSTALLING PROCEDURESPREPARING THE LED/VALET SWITCH:
1. Locate the 4 pin Molex connectorfound in the hardware bag included inthe kit.
2. Carefully plug the terminals at theends of the 4 wires from the switch intothe connector housing as shown.
IMPORTANT ! Be sure to align theterminal correctly before inserting it intothe connector housing.
TOYOTA COROLLA KEYLESS SECURITY ALARM
MOUNTING SHOCK SENSOR MODULE:
A. Use (2) of the short black cable tiesprovided in the hardware bag, and securethe shock sensor to the main vehicleharness as shown in the photo. Adjustthe sensitivity to position 2 for testing.
IMPORTANT NOTE ! Be sure topass the cable ties through theholes in the upper and lowermounting tabs of the shock sensor,then around and securing to themain harness. Failure to do thiscould cause the shock sensor tobecome loose.
SHOCK SENSOR
MOUNTING MAIN CONTROL MODULE:
A. Secure the main module to the vehicleharness connected to the JB in the driver'sside kick panel area. Secure in place withthe long cable ties provided.
NOTE: Guide long cable through themodule eyelets as shown.
Main Module
Southeast Distributors, LLC
Page 6 of 17
TOYOTA COROLLA KEYLESS SECURITY ALARM
ROUTING THE MAIN HARNESS:
1. Route the ignition switch connectors onthe main harness under the steering column.
2. Secure the main harness along it's routingwith the cable ties provided. Be sure thatthe harness is clear of all sharp, hot,moving objects.
INSTALLING PROCEDURES
MOUNTING THE HOOD PIN SWITCH:
1. Route pin switch wire through the bulkheadgrommet nipple from "inside" of the vehicle.Apply a good sealant to seal grommetagainst water entry.
Southeast Distributors, LLC
Page 7 of 17
INSTALLING PROCEDURES
TOYOTA COROLLA KEYLESS SECURITY ALARM
3. Install "star washer" nut on pin switch wireand connect pin switch wire to pin switch asshown.
Hood Switch Location2. Install the "black" flat washer on the pinswitch and guide through the opening on upperradiator support.
4. Thread "starwasher" nut on pin switch andtighten.
Southeast Distributors, LLC
INSTALLING THE SHOCK SENSOR HAR-NESS:
1. Plug the 5 pin end of the harness intothe matting connector on the main controlmodule.
2. Route the harness towards the shocksensor, where it will not interfere with anysharp or moving objects.
3. Secure the harness along the routingpath using the cable ties provided.
IMPORTANT ! After installation, inspect & insure that all Security SystemHarness are clear of all HOT, SHARP or MOVING objects
CONNECTING THE SECURITY SYSTEMHARNESS:
1. Carefully follow the wiring diagram andfactory connector details on pages 9-11 forTMC made vehicle's or pages 12-14 forNUMMI made vehicle's.
SHOCK SENSOR WIRE
Page 8 of 17
T-TAP INSTALLATION:
A. When installing female T - Tap connectors, be sure the wire is located inside the wire channel of thefemale T - Tap connector before closing connector over the wire with pliers ( Figure D ).
Step A Step B Step C
T - Tap Wire from mainsecurity har-ness
TOYOTA COROLLA KEYLESS SECURITY ALARM
Southeast Distributors, LLC
WIR
ING
DIA
GR
AM
4 Pin Molex Connector - Plug Into theL.E.D. / Valet Switch.
[ Hood Pin Switch ] - Locate the BLACK / WHITE hoodpin switch extension wire included in the kit. Plug oneend of the extension wire into the DARK GREEN WIREon the alarm harness, route the extension wire throughthe bulkhead grommet on the driver's side of the vehicle,and plug the other end of the extension onto the hoodpin switch.
Shock Sensor
Page 9 of 17
Disconnect the Ignition SwitchConnector A1 and plug in the securitymain harness into the ignition switchconnectors.
BROWN/WHITE WIRE [ TrunkTrigger ]: Use red T-Tap andconnect to the LT. GREEN wire inconnector 2A, Pin 7.
Relay
10 A
MP
FUS
E
IMPORTANT !The recommended
sensitivity setting for the shocksensor is setting 2 !
WIRING DIAGRAM COROLLA (TMC)
BROWN WIRE [ Door Trigger ]: Usered T-Tap and connect to theWHITE wire in connector 2K, Pin2.
PIN
K [
Doo
r Lo
ck S
witc
h]:
Use
a r
ed T
-Tap
and
conn
ect t
o th
e LT
. BLU
E w
ire in
con
nect
or IE
2,lo
catio
n 16
.
PIN
K/W
HIT
E [
Doo
r Unl
ock
Switc
h]: U
se a
red
T-Ta
p an
d co
nnec
t t
o th
e Y
ELL
OW
wir
e in
conn
ecto
r IE
2, l
ocat
ion
15.
PIN
K/W
HIT
E [D
oor U
nloc
k D
etec
t Sw
itch]
: Use
are
d T-
Tap
and
conn
ect
to t
he Y
ELLO
W w
ire i
nco
nnec
tor
IE1,
loca
tion
9.
[ Cha
ssis
Gro
und
]: C
onne
ct th
e rin
g te
rmin
al to
the
10 m
m b
olt t
o th
e le
ft of
the
stee
ring
colu
mn,
behi
nd t
he f
inis
h pa
nel..
WH
ITE
[D
rive
r D
oor
Unl
ock
Mot
or -
Tow
ards
Doo
r Lo
ck] -
(See
Det
ail A
Bel
ow)
BLU
E/W
HIT
E [ D
river
Doo
r Unl
ock
Mot
or - T
owar
dsB
ody
ECU
] - (S
ee D
etai
l A B
elow
)
DET
AIL
"A"
D
RIV
ER'S
DO
OR
UN
LOC
K C
IRC
UIT
Cut
the
GR
EEN
WIR
E in
con
nect
or IE
2, lo
catio
n 17
.St
rip th
e in
sula
tion
from
bot
h si
des
of th
e cu
t wire
,an
d cr
imp
the
WH
ITE
WIR
E fr
om t
he k
eyle
ssha
rnes
s to
the
HA
RN
ESS
side
of
the
cut
wire
.C
rimp
the
BLU
E/W
HIT
E W
IRE
from
the
key
less
harn
ess
to th
e C
ON
NEC
TOR
sid
e of
the
cut w
ire.
Harn
ess
Wire
s
BLU
E w
/W
HIT
E
Cut
& S
trip
Exis
ting
Wire
WH
ITE
GREEN / ORANGE WIRE [Horn]: Use red T-Tap andconnect to the LT. GREEN WIRE in connector E6,location 8.
BLUE WIRE [Headlights - Automatic TransmissionVehicle]: Use red T-Tap and connect to the BLACKWIRE in connector AE11, location 6. Refer to page 10for additional details.
BLUE WIRE [Headlights - Manual TransmissionVehicle]: Connect BLUE extension harness to the alarmBLUE wire. Use red T-Tap and connect to the BLACKWIRE in connector E91, location 6. Refer to page 11 foradditional details.
WHITE WIRE [Tail Lights]: Use red T-Tap and connectto the WHITE WIRE in connector E8, location 18.
Southeast Distributors, LLC
2. CONNECTOR E6 : HornLocation : Lower Steering Column Cover Area
Pin 8Lt. Green
Horn
Page 10 of 17
Pin 6Black
Headlights
3. CONNECTOR AE11 : HeadlightsLocation : High up in cowl, left of instrument panelAutomatic Transmission Vehicle's
ALARM CARGreen/Orange Lt. Green
Disconnect the Ignition Switch Connector and plugin the security main harness into the ignition switchconnectors.
1 2 3 4
5 6 7 8
1. CONNECTOR E4 : Ignition SwitchLocation : Steering Column
TMC Made Vehicle
121097
641 3 5
11
2
8
ALARM CARBlue Black
TMC Made Vehicle
1 2 3 4 5 6 7 8 9 10
11 12 13 14 15 16 17 18 19 20
4
9
53 6 7
13 1412 15 16
82
18
1
1711107 6 5 4 3
15 1416 13 12
1289
10111718
4. CONNECTOR E8 : TailightsLocation : Lower Steering Column Cover Area
Pin 18White
Tail Lights
ALARM CARWhite White
TMC Made Vehicle
CONNECTOR DETAILS: COROLLA (TMC)
4
9
53 6 7
13 1412 15 16
82
18
1
1711107 6 5 4 3
15 1416 13 12
1289
10111718
5. CONNECTOR IE2 : Door LocksLocation : Driver's Kick Panel Area
Door Lock SwitchLt. Blue WireLocation 16
Door Unlock SwitchYellow WireLocation 15
Driver's Door Lock MotorGreen WireLocation 17**
KEYLESS CARPink Lt. BluePink/White YellowWhite Green (Lock Side)Blue/White Green (ECU Side)
** This vehicle wire must be cut in half, refer to page 9 for instructions.
For manual transmission vehicle's, refer toStep 6, next page.
Door Unlock Detect SwitchYellow WireLocation 9
6. CONNECTOR IE1 : Unlock DetectLocation : Driver's Kick Panel Area
KEYLESS CARPink/White Yellow
1 23 4 5 6 78 9 10 11 12
12
34567
89101112
Blue Connector
8. CONNECTOR 2A : Trunk TriggerLocation : Left Side of Driver's JB
Pin 7Lt. Green
Trunk Trigger
ALARM CARBrown/White Lt. Green
TMC Made Vehicle
2625
11109
24
8
23 30292827
15141312
2120191817
61 5
16
432
22
7
CONNECTOR DETAILS: COROLLA (TMC)
Page 11 of 17
567 34121314 1011
29
18
123456789
101112131415161718
1234
2
1 3456
2
12
1
2
1 1
2
35
1
1
1234567810111213141516 9
45678
1
123458 7 6
23
6543
2
1
98
1110
2423
2625
1312
1514
2827
3029
6
1
5432
721
16
20191817
22
9101112
131415161718
6
1
5432
78
9101112
25262728
13141516
29303132
6
1
5432
78
22
17
21201918
2324
98
2410 2511 26
12 2713 2814 2915 30
23
1
765
222120
234
16171819
1
5 3
2
4
2A
2K
27282930
313233343536
24
19
23222120
2526
7. CONNECTOR 2K : Door TriggerLocation : Left Side of Driver's JB
Pin 2White/Red
Door Trigger
1 2
3 4 5 6
ALARM CARBrown White
TMC Made Vehicle
6. CONNECTOR E91 : Headlights (MT)Location : Behind glove box
Manual Transmission Vehicle's
Pin 6Black
Headlights
ALARM CAR Blue** Black(Extension Wire)
Nummi Made Vehicle
1 23 4 5 6 7 8 9 10 11
12 13 14 15 16 17 18 19 20
** Locate the BLUE extension wire harness inthe security kit. Attach the extension wire to thealarm BLUE wire and route to the glove box,passenger side area. Attach the vehicle BLACKwire, pin 6, as pictured above.
Southeast Distributors, LLC
WIR
ING
DIA
GR
AM
4 Pin Molex Connector - Plug Into theL.E.D. / Valet Switch.
[ Hood Pin Switch ] - Locate the BLACK / WHITE hoodpin switch extension wire included in the kit. Plug oneend of the extension wire into the DARK GREEN WIREon the alarm harness, route the extension wire throughthe bulkhead grommet on the driver's side of the vehicle,and plug the other end of the extension onto the hoodpin switch.
Shock Sensor
Page 12 of 17
Disconnect the Ignition SwitchConnector A1 and plug in the securitymain harness into the ignition switchconnectors.
BROWN/WHITE WIRE [ TrunkTrigger ]: Use red T-Tap andconnect to the LT. GREEN wire inconnector 2A, Pin 7.
Relay
10 A
MP
FUS
E
IMPORTANT !The recommended
sensitivity setting for the shocksensor is setting 2 !
WIRING DIAGRAM COROLLA (NUMMI)
BROWN WIRE [ Door Trigger ]: Usered T-Tap and connect to the GRAYwire in connector 2K, Pin 2.
PIN
K [
Doo
r Lo
ck S
witc
h]:
Use
a r
ed T
-Tap
and
conn
ect
to t
he V
IOLE
T w
ire in
co
nnec
tor
IE2,
loca
tion
16.
PIN
K/W
HIT
E [
Doo
r Unl
ock
Switc
h]: U
se a
red
T-Ta
p an
d co
nnec
t to
the
BEI
GE
wire
in c
onne
ctor
IE2,
loca
tion
15.
PIN
K/W
HIT
E [D
oor U
nloc
k D
etec
t Sw
itch]
: Use
are
d T-
Tap
and
conn
ect
to t
he Y
ELLO
W w
ire i
nco
nnec
tor
IE4,
loca
tion
9.
[ Cha
ssis
Gro
und
]: C
onne
ct th
e rin
g te
rmin
al to
the
10 m
m b
olt t
o th
e le
ft of
the
stee
ring
colu
mn,
behi
nd t
he f
inis
h pa
nel..
WH
ITE
[Driv
er D
oor U
nloc
k M
otor
- To
war
ds D
oor
Lock
] - (S
ee D
etai
l A B
elow
)
BLU
E/W
HIT
E [ D
river
Doo
r Unl
ock
Mot
or - T
owar
dsB
ody
ECU
] - (S
ee D
etai
l A B
elow
)
DET
AIL
"A"
D
RIV
ER'S
DO
OR
UN
LOC
K C
IRC
UIT
Cut
the
GR
EEN
WIR
E in
con
nect
or IE
2, lo
catio
n 17
.St
rip th
e in
sula
tion
from
bot
h si
des
of th
e cu
t wire
,an
d cr
imp
the
WH
ITE
WIR
E fr
om t
he k
eyle
ssha
rnes
s to
the
HA
RN
ESS
side
of
the
cut
wire
.C
rimp
the
BLU
E/W
HIT
E W
IRE
from
the
key
less
harn
ess
to th
e C
ON
NEC
TOR
sid
e of
the
cut w
ire.
Harn
ess
Wire
s
BLU
E w
/W
HIT
E
Cut
& S
trip
Exis
ting
Wire
WH
ITE
GREEN / ORANGE WIRE [Horn]: Use red T-Tap andconnect to the LT. GREEN WIRE in connector E6,location 8.
BLUE WIRE [Headlights - Automatic TransmissionVehicle]: Use red T-Tap and connect to the VIOLETWIRE in connector AE11, location 6. Refer to page 13for additional details.
BLUE WIRE [Headlights - Manual TransmissionVehicle]: Connect BLUE extension harness to the alarmBLUE wire. Use red T-Tap and connect to the VIOLETWIRE in connector E91, location 6. Refer to page 14 foradditional details.
WHITE WIRE [Tail Lights]: Use red T-Tap and connectto the BROWN WIRE in connector E8, location 18.
Southeast Distributors, LLC
2. CONNECTOR E6 : HornLocation : Lower Steering Column Cover Area
Pin 8Lt. Green
Horn
Page 13 of 17
CONNECTOR DETAILS: COROLLA (NUMMI)
Pin 6Violet
Headlights
3. CONNECTOR AE11 : Headlights (AT)Location : High up in cowl, left of instrument panelAutomatic Transmission Vehicle's
ALARM CARGreen/Orange Lt. Green
Disconnect the Ignition Switch Connector and plugin the security main harness into the ignition switchconnectors.
1 2 3 4
5 6 7 8
1. CONNECTOR E4 : Ignition SwitchLocation : Steering Column
Nummi Made Vehicle
121097
641 3 5
11
2
8
ALARM CARBlue Violet
Nummi Made Vehicle
1 2 3 4 5 6 7 8 9 10
11 12 13 14 15 16 17 18 19 20
4
9
53 6 7
13 1412 15 16
82
18
1
1711107 6 5 4 3
15 1416 13 12
1289
10111718
4. CONNECTOR E8 : TailightsLocation : Lower Steering Column Cover Area
Pin 18Brown
Tail Lights
ALARM CARWhite Brown
Nummi Made Vehicle
4
9
53 6 7
13 1412 15 16
82
18
1
1711107 6 5 4 3
15 1416 13 12
1289
10111718
5. CONNECTOR IE2 : Door LocksLocation : Driver's Kick Panel Area
Door Lock SwitchViolet WireLocation 16
Door Unlock SwitchBeige WireLocation 15
Driver's Door Lock MotorGreen WireLocation 17**
KEYLESS CARPink VioletPink/White BeigeWhite Green (Lock Side)Blue/White Green (ECU Side)
** This vehicle wire must be cut in half, refer to page 12 for instructions.
For manual transmission vehicle's, refer toStep 6, next page.
Door Unlock Detect SwitchYellow WireLocation 9
6. CONNECTOR IE4 : Unlock DetectLocation : Driver's Kick Panel Area
KEYLESS CARPink/White Yellow
1 23 4 5 6 78 9 10 11 12
12
34567
89101112
White Connector
7. CONNECTOR 2A : Trunk TriggerLocation : Left Side of Driver's JB
Pin 7Lt. Green
Trunk Trigger
ALARM CARBrown/White Lt. Green
Nummi Made Vehicle
2625
11109
24
8
23 30292827
15141312
2120191817
61 5
16
432
22
7
CONNECTOR DETAILS: COROLLA (NUMMI)
Page 14 of 17
8. CONNECTOR 2K : Door TriggerLocation : Left Side of Driver's JB
Pin 2Gray
Door Trigger
1 2
3 4 5 6
ALARM CARBrown Gray
Nummi Made Vehicle
567 34121314 1011
29
18
123456789
101112131415161718
1234
2
1 3456
2
12
1
2
1 1
2
35
1
1
1234567810111213141516 9
45678
1
123458 7 6
23
6543
2
1
98
1110
2423
2625
1312
1514
2827
3029
6
1
5432
721
16
20191817
22
9101112
131415161718
6
1
5432
78
9101112
25262728
13141516
29303132
6
1
5432
78
22
17
21201918
2324
98
2410 2511 26
12 2713 2814 2915 30
23
1
765
222120
234
16171819
1
5 3
2
4
2A
2K
27282930
313233343536
24
19
23222120
2526
6. CONNECTOR E91 : Headlights (MT)Location : Behind glove box
Manual Transmission Vehicle's
Pin 6Violet
Headlights
ALARM CAR Blue** Violet(Extension Wire)
Nummi Made Vehicle
1 23 4 5 6 7 8 9 10 11
12 13 14 15 16 17 18 19 20
** Locate the BLUE extension wire harness inthe security kit. Attach the extension wire to thealarm BLUE wire and route to the glove box,passenger side area. Attach the vehicle VIOLETwire, pin 6, as pictured above.
Southeast Distributors, LLC
1. Sit in the driver's seat, insert the ignition key andturn to the ON position.
2. Press the valet control switch and verify that theLED light responds. Light should go ON and OFFwith actuation of the valet control switch.
3. With the LED indicator light ON, ignition OFF andkey removed, the security system is in the valetmode and the alarm should not arm. Press the"LOCK" button, the parking lights will flash once,all doors will lock, headlights come on for 20seconds. Press the "UNLOCK" button, theparking lights will flash twice, driver's door onlywill unlock, headlights come on for 20 seconds.
4. Ignition key ON, LED light OFF, ignition key OFF.
1. Rearm the security system by pressing the "LOCK"button. Open any door or hatch. The systemshould simultaneously sound the horn and flashthe parking lights.
2. Disarm the security system by pressing the"UNLOCK" button. The system should sound (4)chirps of the horn, the parking lights should flash(4) times, indicating vehicle intrusion.
3. The LED should indicate the point of intrusionafter disarming the system. Observe the LED for1, 2, or 3 flashes. Compare your observations tothe following.
1. Press the "LOCK" button to arm the system. Usethe key to unlock and open the driver's door. Thealarm will sound. Enter the vehicle, insert theignition key and turn to the on position. Press thevalet control switch once, the alarm shoulddeactivate and the vehicle should now start.
1. Set in the driver's seat with all the doors closed.Press the "LOCK" button to arm the system. Insertthe ignition key and turn to the start position. Thestarter should not crank the engine. Press the"UNLOCK" button to disarm the system. Turn tothe start position. The starter should crank theengine. Exit vehicle.
1. Press the "LOCK" button, the system should armand lock all doors.
2. Press the "UNLOCK" button, the system willalso disarm and unlock the driver's door.
3. Press the "UNLOCK" button a second time andall doors should unlock.
F. STARTER INTERRUPT:
G. DEFECTIVE OR LOST TRANSMITTER:
H. REMOTE TRANSMITTER OPERATION:
I. INTRUSION TEST:
END
SYSTEM AUTOMATICALLY CLEARS ALLSTORED VIOLATIONS WHEN THE IGNITIONSWITCH IS TURNED TO THE "ON" POSITION.
(1) Flash = Shock(2) Flashes = Hood(3) Flashes = Vehicle Doors
TESTING ALARM SYSTEM:
B. Test BOTH remote transmitters, one at a time.Press and release the "LOCK" button. If the LEDlight on the transmitters fails to glow, you needto check the transmitter battery.
1. Press the "LOCK" button to arm the system. Withthe open palm lightly slap the "A" pillar by thedriver's windshield. You should hear short chirpsfrom the vehicle horn. This is a check of the shocksensor "WARN-AWAY" function. Allow a fewseconds for the shock to settle, then conduct thesame check at various points around the vehicle.Sensitivity can be adjusted at the shock sensor forbest response.
2. Slap the vehicle at the "A" pillar with slightly moreforce. The vehicle should go into full alarm. Pressthe "UNLOCK" button to disarm the system. Rearmthe vehicle and conduct the same check at variouspoints around the vehicle. Adjust sensitivity at theshock sensor for the best response.
SHOCK SENSOR
sensitivity adjustment
E. SHOCK SENSOR:
LED Light
Lock Button
Panic RED Button
(Rear Cover)
Unlock Button
C. VALET CONTROL SWITCH:
5. Press and hold the "RED" button to test the "Panic"function. The alarm should blow the horn in short,continuous blast, parking lights should beflashing.
1. Put all vehicle windows down and close hood andall doors.
2. Press and release the "LOCK" transmitter button.3. All doors should lock, parking lights flash once,
horn chirps once, headlights come on for 20seconds and the LED should flash slowly. (Note:If the parking lights flash three times and the hornchirps three times, check for an open hood ordoor.)
4. Press the "UNLOCK" button, the horn chirps (2)times, parking lights flash (2) times, headlightscome on for 20 seconds, driver's door onlyunlocks.
D. ARMING/DISARMING & PANIC:
Page 15 of 17
A. RECONNECT THE BATTERY: Connect Negative cable to vehicle battery and torque to 36in. lbs.
Negative Battery Cable
TOYOTA COROLLA KEYLESS SECURITY ALARM
Southeast Distributors, LLC
COMPLETING THE INSTALLATIONASSEMBLE ALL REMOVED PANELS:
1. Refer again to the vehicle repair manualand re-assemble all panels that wereremoved. Test thoroughly, all mechanicaland electrical components disconnectedand or removed from the vehicle duringthe installation of this accessory.
PREPARING VEHICLE FOR DELIVERY:
Turn the arm/disarm chirps off:1. Start with the LED/Valet switch in the off(out) position.2. Turn the ignition key to the on position.3. Turn the ignition key off, then immediatelypress and release the LED/Valet switch 3times. (You will hear 2 chirps to confirmthat the chirps were turned off.)
Place the system into Valet mode. (VPConly)1. Start with the LED/Valet switch in the off(out) position.2. Turn the ignition key to the on position.3. Press the LED/Valet switch one time. Theswitch is in the (in) position, and the red LEDlight is turned on solid, indicating that thesystem is in the Valet Mode.
IMPORTANT: Clean the window beforeapplying the security decal.
Applying the window warning decal:1. Apply the window warning decals to thedriver side and passenger side windows,just above the anti-theft radio stickers ifequipped. If not equipped, apply the decalsat the lower rear edge of the window. (Thedecals are reverse printed and are appliedto the inside surface of the glass.
Owners Manual:1. Leave the Keyless Entry Security owner'smanual in the vehicle glove box.
Page 16 of 17
WINDOW
3/8"
1"
LED
TOYOTA COROLLA KEYLESS SECURITY ALARM
Southeast Distributors, LLC
STEP 2
PROGRAMMING NEW or REPLACEMENT TRANSMITTERS TO THE SECURITY MODULE:IMPORTANT NOTE : Once you enter the programming mode, if 15 seconds elapse with no activity on thesystem, the programming mode will be terminated. If this happens, simply start over.
STEP 1
Turn the vehicle’s ignition keyON then OFF 7 times.....
....Ending in the OFF position.
To get started, enter the vehicle and close all doors,then lock the doors by using the door lock switchmounted on the driver’s door panel.
STEP 3Press and Hold the Lock button on the transmitteruntil the Driver’s Door Unlocks.
STEP 4Lock all doors by using the door lock switchmounted on the driver’s door panel.
STEP 5Repeat Steps 3 and 4 for all transmitters that youneed to program to operate the vehicle.
(Maximum of 4 transmitters per vehicle)
STEP 6When all transmitters havebeen programmed, turn theignition key ON then OFF toexit the program mode.
TOYOTA COROLLA KEYLESS SECURITY ALARM
Page 17 of 17Southeast Distributors, LLC