TP48200A-D15A1 & H15A3 & H15A5 V300R001 Quick Installation Guide 06

TP48200A-D15A1 & H15A3 & H15A5 V300R001

Quick Installation Guide

Issue 06

Date 2013-07-23

HUAWEI TECHNOLOGIES CO., LTD.

Issue 06 (2013-07-23) Huawei Proprietary and Confidential

Copyright Huawei Technologies Co., Ltd.

i

Copyright Huawei Technologies Co., Ltd. 2013. All rights reserved.

No part of this document may be reproduced or transmitted in any form or by any means without prior

written consent of Huawei Technologies Co., Ltd.

Trademarks and Permissions

and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.

All other trademarks and trade names mentioned in this document are the property of their respective

holders.

Notice

The purchased products, services and features are stipulated by the contract made between Huawei and

the customer. All or part of the products, services and features described in this document may not be

within the purchase scope or the usage scope. Unless otherwise specified in the contract, all statements,

information, and recommendations in this document are provided "AS IS" without warranties, guarantees or

representations of any kind, either express or implied.

The information in this document is subject to change without notice. Every effort has been made in the

preparation of this document to ensure accuracy of the contents, but all statements, information, and

recommendations in this document do not constitute a warranty of any kind, express or implied.

Huawei Technologies Co., Ltd.

Address: Huawei Industrial Base

Bantian, Longgang

Shenzhen 518129

People's Republic of China

Website: http://www.huawei.com

Email: [email protected]

TP48200A-D15A1 & H15A3 & H15A5

Quick Installation Guide About This Document



ii

About This Document

Purpose

This document describes the TP48200A-D15A1 & H15A3 & H15A5 in terms of its structure,

components, installation, and commissioning.

Intended Audience

This document is intended for:

Installation and commissioning engineers

Technical support engineers

Symbol Conventions

The symbols that may be found in this document are defined as follows.

Symbol Description

Indicates a hazard with a high level or medium level of risk

which, if not avoided, could result in death or serious injury.

Indicates a hazard with a low level of risk which, if not

avoided, could result in minor or moderate injury.

Indicates a potentially hazardous situation that, if not avoided,

could result in equipment damage, data loss, performance

deterioration, or unanticipated results.

Provides a tip that may help you solve a problem or save time.

Provides additional information to emphasize or supplement important points in the main text.

TP48200A-D15A1 & H15A3 & H15A5

Quick Installation Guide About This Document



iii

Change History

Changes between document issues are cumulative. The latest document issue contains all the

changes made in earlier issues.

Issue 06 (2013-07-23)

Modified section 7.1.1 UIM02C.

Issue 05 (2013-04-28)

Optimized the content of the document, including standardizing the terminology and

improving the accuracy of the description.

Issue 04 (2013-02-28)

Add the installation dimensions for the cabinet installation holes.

Issue 03 (2013-01-09)

This issue is the third official release, which incorporates the following changes:

Chapter 6 Installing Components

Modify the picture of Install a temperature and humidity sensor.

Chapter 8 Powering On and Commissioning

Set battery fuse break alarm "Enable/Disable" status is added.

Issue 02 (2012-11-12)

This issue is the second official release, which incorporates the following changes:

Port description is modified.

Issue 01 (2012-07-28)

This issue is used for first office release.

TP48200A-D15A1 & H15A3 & H15A5

Quick Installation Guide Contents



iv

Contents

About This Document .................................................................................................................... ii

1 Safety Precautions ......................................................................................................................... 1

1.1 Health and Safety ............................................................................................................................................. 1

1.1.1 Overview ................................................................................................................................................. 1

1.1.2 Electrical Safety ...................................................................................................................................... 3

1.1.3 Inflammable Environment ...................................................................................................................... 4

1.1.4 Battery ..................................................................................................................................................... 4

1.1.5 Working at Heights ................................................................................................................................. 6

1.1.6 Using Ladders ......................................................................................................................................... 7

1.1.7 Mechanical Safety ................................................................................................................................... 7

1.1.8 Bundling Signal Cables ........................................................................................................................... 8

1.2 Equipment Safety ............................................................................................................................................. 9

1.2.1 Electricity Safety ..................................................................................................................................... 9

1.2.2 Electrostatic Discharge............................................................................................................................ 9

1.2.3 Laying Cables ....................................................................................................................................... 10

2 Installation Preparations ........................................................................................................... 11

2.1 Tools ............................................................................................................................................................... 11

2.2 Installation Clearance Requirements .............................................................................................................. 12

2.3 Prepare Cables ................................................................................................................................................ 12

3 Configuration ............................................................................................................................... 14

4 Installing the Cabinet ................................................................................................................. 18

5 Installing a PGND Cable ........................................................................................................... 21

6 Installing Components............................................................................................................... 22

6.1 Installing Rectifiers ........................................................................................................................................ 22

6.2 Installing a Smoke Sensor(Optional) ............................................................................................................. 23

6.2.1 Securing the Smoke Sensor ................................................................................................................... 23

6.2.2 Connecting the Smoke Sensor .............................................................................................................. 23

6.3 Installing a Temperature and Humidity Sensor(Optional) .............................................................................. 24

6.3.1 Securing the Temperature and Humidity Sensor ................................................................................... 24

6.3.2 Connecting the Temperature and Humidity Sensor ............................................................................... 24

TP48200A-D15A1 & H15A3 & H15A5

Quick Installation Guide Contents



v

6.4 Installing a Water Sensor(Optional) ............................................................................................................... 25

6.4.1 Securing the Water Sensor .................................................................................................................... 25

6.4.2 Connecting the Water Sensor ................................................................................................................ 25

7 Installing Cables ......................................................................................................................... 27

7.1 Installing Signal Cables and Communication Cables ..................................................................................... 27

7.1.1 UIM02C ................................................................................................................................................ 27

7.1.2 Installing Dry Contacts and Boolean Values Signal Cables .................................................................. 29

7.1.3 Installing Sensor Cables ........................................................................................................................ 29

7.1.4 Installing Communications Cables ....................................................................................................... 30

7.2 Installing Power Cables .................................................................................................................................. 30

7.2.1 Installing DC Output Cables ................................................................................................................. 31

7.2.2 Installing Storage Batteries and Copper Bars ....................................................................................... 32

7.2.3 Installing AC Output Cables ................................................................................................................. 34

7.2.4 Installing AC Input Cables .................................................................................................................... 35

8 System Commissioning ............................................................................................................. 38

8.1 Installation Verification .................................................................................................................................. 38

8.2 Powering On and Commissioning .................................................................................................................. 38

8.2.1 Setting Parameters ................................................................................................................................ 38

8.3 Powering On................................................................................................................................................... 42

TP48200A-D15A1 & H15A3 & H15A5

Quick Installation Guide 1 Safety Precautions



1

1 Safety Precautions 1.1 Health and Safety

1.1.1 Overview

Introduction

This section describes the safety precautions you must take before installing or maintaining

Huawei equipment.

To ensure safety of humans and the equipment, pay attention to the safety symbols on the

equipment and all the safety instructions in this document.

The "NOTE", "CAUTION", and "WARNING" marks in other documents do not

represent all the safety instructions. They are only supplements to the safety instructions.

Installation and maintenance personnel must understand basic safety precautions to avoid

hazards.

When operating Huawei equipment, in addition to following the general precautions in

this document, follow the specific safety instructions given by Huawei.

Only trained and qualified personnel are allowed to install, operate, and maintain Huawei

equipment.

Local Safety Regulations

When operating Huawei equipment, you must follow the local laws and regulations. The

safety instructions in this document are only supplements to the local laws and regulations.

General Requirements

To minimize risk of personal injury and damage to equipment, read and follow all the

precautions in this document before performing any installation or maintenance.

Ensure that the instructions provided in this document are followed completely. This section

also provides guidelines for selecting the measuring and testing devices.

Installation The device (or system) must be installed in an access-controlled location.

The device can be mounted only on concrete or non-combustible surfaces.

TP48200A-D15A1 & H15A3 & H15A5




2

The device must be fixed securely on the floor or to other immovable objects such as

walls and mounting racks before operation.

When installing the unit, always make the ground connection first and disconnect it at

the end.

Do not block the ventilation while the device is operating. Keep a minimum distance of 5

cm between the device and the wall or other objects that may block the ventilation.

Tighten the thumbscrews by using a tool after initial installation and subsequent access

to the panel.

Ground Do not damage the ground conductor or operate the device in the absence of a properly

installed ground conductor. Conduct the electrical inspection carefully.

The device (or system) must be connected permanently to the protection ground before

an operation. The cross-sectional area of the protective ground conductor must be at least

10 mm2.

Power Supply For AC-supplied models: The device applies to TN or TT power system.

For DC-supplied models: Reinforced insulation or double insulation must be provided to

isolate the DC source from the AC mains supply.

For DC-supplied model: The device applies to DC power source that complies with the

Safety Extra-Low Voltage (SELV) requirements in IEC 60950-1 based safety standards.

Prepared conductors are connected to the terminal block, and only the appropriate

AWG/Type of wire is secured with the lug terminals.

Human Safety Do not operate the device or cables during lightning strikes.

Remove the AC power connector when there is lightning. Do not use fixed terminals or

touch terminals or antenna connectors when there is lightning.

To avoid electric shock, do not connect safety extra-low voltage (SELV) circuits to

telecommunication network voltage (TNV) circuits.

Move or lift the chassis by holding its lower edge. Do not hold the handles on certain

modules such as power supply, fans, and boards because they cannot support the weight

of the device.

At least two persons are required to lift the chassis. When lifting it, keep your back

straight and move stably.

Do not wear jewelry or watches when you operate the device.

Operator Only qualified professional personnel are allowed to install, configure, operate, and

disassemble the device.

Only the personnel authenticated or authorized by Huawei are allowed to replace or

change the device of the parts of the device (including the software).

Any fault or error that might cause safety problems must be reported immediately to a

supervisor.

Only qualified personnel are allowed to remove or disable the safety facilities and to

troubleshoot and maintain the device.

TP48200A-D15A1 & H15A3 & H15A5




3

1.1.2 Electrical Safety

High Voltage

The high voltage power supply provides power for the device operation. Direct or indirect

contact (through damp objects) with high voltage and AC mains supply may result in fatal

danger.

During the installation of the AC power supply facility, follow the local safety

regulations. The personnel who install the AC facility must be qualified to perform high

voltage and AC operations.

Do not wear conductive articles, such as watches, hand chains, bracelets, and rings

during the operation.

When water is found in the rack or the rack is damp, switch off the power supply

immediately.

When the operation is performed in a damp environment, make sure that the device is

dry.

Non-standard and improper high voltage operations may result in fire and electric shock.

Therefore, you must abide by the local rules and regulations when bridging and wiring AC

cables. Only qualified personnel are allowed to perform high voltage and AC operations.

Before powering on a device, ground the device. Otherwise, personal injury or device damage

may be caused by high leakage current.

Tools

Dedicated tools must be used during high voltage and AC operations. Avoid using ordinary

tools.

TP48200A-D15A1 & H15A3 & H15A5




4

High Electrical Leakage

Ground the device before powering it on. Otherwise, personal injury or device damage may

be caused by high leakage current.

If a "high electrical leakage" tag is present on the power terminal of the device, you must

ground the device before powering it on.

Power Cable

Do not install or remove power cables when the device is on. Transient contact between the

core of the power cable and the conductor may generate electric arcs or sparks, which may

cause fire or hurt human eyes.

Before installing or removing the power cable, turn off the power switch.

Before connecting a power cable, check that the label on the power cable is correct.

1.1.3 Inflammable Environment

Operating the electrical device in an inflammable environment can be fatal.

Do not place the device in an environment that has inflammable and explosive air or gas. Do

not perform any operation in this environment.

1.1.4 Battery

Storage Battery

Before operating storage batteries, carefully read the safety precautions for battery handling

and connection.

TP48200A-D15A1 & H15A3 & H15A5




5

Improper handling of storage batteries causes hazards.

When operating storage batteries, avoid short circuit and overflow or leakage of the

electrolyte. Electrolyte overflow may damage the device. It will corrode metal parts and

circuit boards, and ultimately damage the device and cause short circuit of circuit boards.

Basic Precautions

Before installing and maintaining the battery, note the following:

Do not wear metal articles such as wristwatch, hand chain, bracelet, and ring.

Use special insulation tools.

Take care to protect your eyes when operating the device.

Wear rubber gloves and a protective coat in case of electrolyte overflow.

When handling a storage battery, ensure that its electrodes are upward. Leaning or

reversing the storage battery is prohibited.

Short Circuit

Battery short circuit may cause human injuries. Although the voltage of ordinary batteries is

low, the instantaneous high current caused by the short circuit releases a great deal of energy.

There is danger of explosion if the battery is incorrectly replaced. Therefore, replace the

battery only with the same or equivalent type recommended by the manufacturer.

Keep away metal objects, which may cause battery short circuit, from batteries. If metal

objects must be used, first disconnect the batteries in use before performing any other

operations.

Hazardous Gas

TP48200A-D15A1 & H15A3 & H15A5




6

Do not use unsealed lead acid storage batteries. Lead acid storage batteries must be placed

horizontally and stably to prevent the batteries from releasing flammable gas, which may

cause fire or erode the device.

Lead acid storage batteries in use emit flammable gas. Therefore, ventilation and

fireproofing measures must be taken at the sites where lead acid storage batteries are used.

Battery Temperature

If a battery overheats, the battery may be deformed or damaged, and the electrolyte may

overflow.

When the temperature of the battery is higher than 60 C, check the battery for electrolyte

overflow. If the electrolyte overflows, absorb and counteract the electrolyte immediately.

Battery Leakage

When the electrolyte overflows, absorb and counteract the electrolyte immediately.

When moving or handling a battery whose electrolyte leaks, note that the leaking electrolyte

may hurt human bodies. When you find the electrolyte leaks, use the following substances to

counteract and absorb the leaking electrolyte:

Sodium bicarbonate (baking soda): NaHCO3

Sodium carbonate (soda): Na2CO3

Select a substance to counteract and absorb the leaking electrolyte according to the

instructions of the battery manufacturer.

1.1.5 Working at Heights

Avoid object falling when you work at heights.

When working at heights, fulfill the following requirements:

Only trained personnel can work at heights.

TP48200A-D15A1 & H15A3 & H15A5




7

Prevent the devices and tools that you carry from falling down.

Take safety and protection measures, for example, wear a helm and safety belt.

Wear warm clothes when working at heights in a cold region.

Before working at heights, check that all the lifting facilities are in good condition.

1.1.6 Using Ladders

Checking a Ladder Before using a ladder, check whether the ladder is damaged. Only the ladder in good

condition can be used.

Before using a ladder, you should know the maximum weight capacity of the ladder.

Avoid overweighing the ladder.

Placing a Ladder

The recommended gradient of ladders is 75 degrees. You can measure the gradient of the

ladder with an angle square or your arms. When using a ladder, ensure that the wider feet of

the ladder are downward, or take protection measures for the ladder feet to prevent the ladder

from sliding. Ensure that the ladder is placed securely.

Climbing Up a Ladder

When climbing up a ladder, note the following:

Ensure that the center of gravity of your body does not deviate from the edges of the two

long sides.

To minimize the risk of falling, hold your balance on the ladder before any operation.

Do not climb higher than the fourth rung of the ladder (counted from up to down).

If you want to climb up a roof, ensure that the ladder top is at least one meter higher than

the roof.

1.1.7 Mechanical Safety

Drilling Holes

Do not drill the cabinet at will. Drilling holes without complying with the requirements affects

the electromagnetic shielding performance of the cabinet and damages the cables inside the

cabinet. In addition, if the scraps caused by drilling enter the cabinet, the printed circuit

boards (PCBs) may be short circuited.

Before you drill a hole in the cabinet, wear insulated gloves and remove the internal

cables from the cabinet.

Wear an eye protector when drilling holes. This is to prevent your eyes from being

injured by the splashing metal scraps.

Ensure that the scraps caused by drilling do not enter the cabinet.

TP48200A-D15A1 & H15A3 & H15A5




8

Drilling holes without complying with the requirements affects the electromagnetic

shielding performance of the cabinet.

After drilling, clean the metal scraps immediately.

Sharp Objects

Before you hold or carry a device, wear protective gloves to avoid getting injured by sharp

edges of the device.

Handling Fans

When handling fans, note the following:

When replacing a component, place the component, screws, and tools in a safe place.

Otherwise, if any of them fall into the operating fans, the fans may be damaged.

When replacing a component near fans, do not insert your fingers or boards into the

operating fans until the fans are switched off and stops running.

Lifting Heavy Objects

When heavy objects are being lifted, do not stand or walk under the cantilever or the lifted

object.

1.1.8 Bundling Signal Cables

Do not bundle signal cables with high current cables or high voltage cables.

Maintain a minimum space of 150 mm between adjacent ties.

TP48200A-D15A1 & H15A3 & H15A5




9

1.2 Equipment Safety

1.2.1 Electricity Safety

High Electrical Leakage

If the "high electrical leakage" tag is present on the power terminal of the device, you must

ground the device before powering it on.

1.2.2 Electrostatic Discharge

The static electricity generated by human bodies may damage the electrostatic-sensitive

components on boards, for example, the large-scale integrated (LSI) circuits.

Human body movement, friction between human bodies and clothes, friction between shoes

and floors, or handling of plastic articles causes static electromagnetic fields on human bodies.

These static electromagnetic fields cannot be eliminated until the static is discharged.

To prevent electrostatic-sensitive components from being damaged by the static on human

bodies, you must wear a well-grounded ESD wrist strap when touching the device or handling

boards or application-specific integrated circuits (ASICs).

Figure 1-1 shows how to wear an ESD wrist strap.

Figure 1-1 Wearing an ESD wrist strap

TP48200A-D15A1 & H15A3 & H15A5




10

1.2.3 Laying Cables

When the temperature is very low, violent strike or vibration may damage the cable sheathing.

To ensure safety, comply with the following requirements:

Cables can be laid or installed only when the temperature is higher than 0 C.

Before laying cables which have been stored in a temperature lower than 0 C, move the

cables to an environment of the ambient temperature and store them at the ambient

temperature for at least 24 hours.

Handle cables with caution, especially at a low temperature. Do not drop the cables

directly from the vehicle.

TP48200A-D15A1 & H15A3 & H15A5

Quick Installation Guide 2 Installation Preparations



11

2 Installation Preparations 2.1 Tools

Table 2-1 shows the tools that must be obtained before installation.

Table 2-1 Tools

Combination

spanner

Marker pen

Rubber hammer

Phillips

screwdriver

Flathead

screwdriver

Socket spanner

Wire clippers

Hydraulic pliers

Torque spanner

Diagonal plier

Adjustable

spanner

Paper knife

Network cable

pliers

Sharp-nose pliers

Wire stripper

RJ-45.connect

or crimping

pliers

Power cable

cutting pliers

Power cable

crimping pliers

Crimping pliers

ESD-preventiv

e wrist strap

Percussion

drill

Drill bit

Clamp meter

Hot air dun

Steel tape

Vacuum cleaner

Multimeter

Antistatic gloves

Protective gloves

TP48200A-D15A1 & H15A3 & H15A5




12

2.2 Installation Clearance Requirements Figure 2-1 shows the installation clearance requirements.

Figure 2-1 Installation clearance requirements

2.3 Prepare Cables

Table 2-2 lists the specification of the system cables.

Table 2-2 The specification of the system cables

Cable Cable Diameter and Color

Signal cables to dry contacts,

Boolean values, and sensor ports Not provided

RS485, RS232 or Fast Ethernet

(FE) cable Not provided

DC Power cable to the primary

load Not provided

DC Power cable to the secondary

load Not provided

The PGND cable Cross-sectional area: 16 mm2 (0.02 in.2) Color: yellow green cable

AC input power cable single-phase: Cross-sectional area: 25 mm2 (0.04 in.

2 )

three-phase: Cross-sectional area: 16 mm2

(0.02 in.2

)

TP48200A-D15A1 & H15A3 & H15A5




13

Cable Cable Diameter and Color (recommended /Not provided)

Cut cables to a length suitable for the actual cable route, and then add OT terminals or cord

end terminals to each end of the cables, as shown in Figure 2-2, Figure 2-3.

Figure 2-2 Prepare OT terminals

Figure 2-3 Prepare cord end terminals.

The local cable colors prevail. The cable colors in the figure are for reference only.

Cables routed along the floor should be protected with protection tubes that comply with NFPA70

standards.

NOTE

TP48200A-D15A1 & H15A3 & H15A5

Quick Installation Guide 3 Configuration



14

3 Configuration Specifications

Table 3-1 Specifications

Category Specifications

Dimensions (H x W x D) Cabinet: 1500 mm (59.06 in.) x 650 mm (25.59 in.) x 650

mm (25.59 in.)

Base: 100 mm (3.94 in.) x 650 mm (25.59 in.) x 650 mm

(25.59 in.)

Weight 120 kg (264.6 lb) (without rectifiers or storage batteries)

TP48200A-D15A1 & H15A3 & H15A5




15

Interior of the Cabinet

Figure 3-1 Interior of the TP48200A-D15A1

(1) Maintenance socket (2) AC input circuit breakers (3) Ground bar

(4) Cable hole (5) Storage battery circuit breakers (6) Load circuit breakers

(7) Site monitoring unit (SMU) (8) Space for rectifiers (9) Battery rack

TP48200A-D15A1 & H15A3 & H15A5




16

Figure 3-2 Interior of the TP48200A- H15A3



(7) Site monitoring unit (SMU) (8) Space for rectifiers (9) Battery rack

TP48200A-D15A1 & H15A3 & H15A5




17

Figure 3-3 Interior of the TP48200A-H15A5



(7) Site monitoring unit (SMU) (8) Space for rectifiers (9) Heater

(10) Battery rack

TP48200A-D15A1 & H15A3 & H15A5

Quick Installation Guide 4 Installing the Cabinet



18

4 Installing the Cabinet To install a cabinet, perform the following steps:

Step 1 Remove the cover of the packaging box and locate the marking-off template on the cover interior, as shown in Figure 4-1.

Figure 4-1 Marking-off template

Step 2 Fix the installation hole, as shown in Figure 4-2.

Figure 4-2 Fixing the installation hole

(1) Marker (2) Marking-off template (3) Installation hole

(4) Concrete pad

TP48200A-D15A1 & H15A3 & H15A5




19

Step 3 Drill holes and install expansion sleeves, as shown in Figure 4-3.

Figure 4-3 Drilling holes and install expansion sleeves

(1) Expansion bolt(M12) (2) Spring washer (3) Flat washer (4) Expansion sleeve

(5) Concrete pad

Step 4 Remove the cabinet from the pallet, as shown in Figure 4-4.

Figure 4-4 Removing the cabinet

(1) Pallet

The configuration prevail, the pallet in the figure is for reference only

Step 5 Secure the cabinet on the concrete pad, as shown in Figure 4-5.

NOTE

TP48200A-D15A1 & H15A3 & H15A5




20

Figure 4-5 Securing the cabinet

----End

TP48200A-D15A1 & H15A3 & H15A5

Quick Installation Guide 5 Installing a PGND Cable



21

5 Installing a PGND Cable The PGND cable is used to connect PGND screws on the cabinet and the ground busbar

outside the cabinet to ensure proper grounding of the cabinet.

Install the PGND cable as shown in Figure 5-1.

Figure 5-1 Installing the PGND cable

(1) Ground bar for the site (2) Ground bar for the cabinet

TP48200A-D15A1 & H15A3 & H15A5

Quick Installation Guide 6 Installing Components



22

6 Installing Components 6.1 Installing Rectifiers

The rated output current of each rectifier is 50 A. The number of rectifiers depends on actual

capacity requirements.as shown in Figure 6-1 and Figure 6-2.

Figure 6-1 Removing the filler panel

Figure 6-2 Installing rectifiers

TP48200A-D15A1 & H15A3 & H15A5




23

6.2 Installing a Smoke Sensor(Optional)

6.2.1 Securing the Smoke Sensor

Secure the smoke sensor base to the cabinet top using two M4 mm screws and fasten the

smoke sensor to the base based on the direction shown in the smoke sensor, as shown in

Figure 6-3.

Figure 6-3 Installing a Smoke Sensor

6.2.2 Connecting the Smoke Sensor

Connect one end of the smoke sensor signal cable to the "SMOKE" port on the UIM02C and

the other end to the port on the smoke sensor, as shown in Figure 6-4.

Figure 6-4 Connect the smoke sensor

TP48200A-D15A1 & H15A3 & H15A5




24

6.3 Installing a Temperature and Humidity Sensor(Optional)

6.3.1 Securing the Temperature and Humidity Sensor

Secure the temperature and humidity sensor base to the cabinet top, as shown in Figure 6-5.

Step 1 Secure the temperature and humidity sensor base to the cabinet top using two M4 mm screws.

Step 2 Connect and secure signal cables of the temperature and humidity sensor to the cabinet base, as shown in the following figure

Step 3 Install the top cover of the temperature and humidity sensor to the cabinet base.

Step 4 The final installation view is as follows.

Figure 6-5 Installing a temperature and humidity sensor

----End

6.3.2 Connecting the Temperature and Humidity Sensor

Connect one end of the temperature and humidity sensor signal cable to the "TEM-HUM"

port on the UIM02C and the other end to the port on the temperature and humidity sensor, as

shown in Figure 6-6.

TP48200A-D15A1 & H15A3 & H15A5




25

Figure 6-6 Connecting the temperature and humidity sensor

6.4 Installing a Water Sensor(Optional)

6.4.1 Securing the Water Sensor

Secure the water sensor to the cabinet bottom using cable ties, as shown in Figure 6-7.

Figure 6-7 Installing a Water Sensor

6.4.2 Connecting the Water Sensor

Connect one end of the water sensor signal cable to the "WATER" port on the UIM02C, as

shown in Figure 6-8

TP48200A-D15A1 & H15A3 & H15A5




26

Figure 6-8 Connecting the water sensor

TP48200A-D15A1 & H15A3 & H15A5

Quick Installation Guide 7 Installing Cables



27

7 Installing Cables 7.1 Installing Signal Cables and Communication Cables

7.1.1 UIM02C

All ports in this manual are protected by a security mechanism.

The user interface module (UIM02C) supports eight dry contact outputs, nine Boolean value

inputs (including general DI1-6, smoke, water, door status), three analog signals inputs

(ambient temperature, humidity, and battery temperature).

Appearance

Figure 7-1 UIM02C panel

Port Description

Table 7-1 UIM02C port description

Port Type Silkscreen Description Default Mode

Sensor

ports

TEM_HUM Temperature and humidity

sensor

-

WATER Water sensor -

TEMP1 Connected to environment

temperature sensor and used

for fan speed adjustment

-

NOTE

TP48200A-D15A1 & H15A3 & H15A5




28

Port Type Silkscreen Description Default Mode

TEMP2 Reserved -

GATE Door status sensor -

SMOKE Smoke sensor -

BTEMP Battery temperature sensor -

Boolean

value input

ports

DIN1 Boolean value input 1 Close: alarm

Open: normal


Open: normal


Open: normal


Open: normal

DIN5 Boolean value input 5 Open: alarm

Close: normal


Open: normal

Dry

contact

output

ports

Default

mode

(Close:

alarm;

Open:

normal)

can be

modified

as

required.

ALM1 AC power failure alarm Close: alarm

Open: normal

ALM2 DC undervoltage alarm or DC

overvoltage alarm

Close: alarm

Open: normal

ALM3 Rectifier faults, Protect and No

Response alarm Close: alarm

Open: normal

ALM4 SPD failure alarm Close: alarm

Open: normal

ALM5 Fuse burn-out alarm Close: alarm

Open: normal

ALM6 Battery or environment

temperature alarms

Close: alarm

Open: normal

ALM7 Door alarms Close: alarm

Open: normal

ALM8 Heater faults alarms and Fan

faults alarms

Close: alarm

Open: normal

Communic

ation Port

COM RS485

TP48200A-D15A1 & H15A3 & H15A5




29

7.1.2 Installing Dry Contacts and Boolean Values Signal Cables

Install dry contacts and Boolean values signal cables, as shown in Figure 7-2.

Figure 7-2 Installing dry contacts and Boolean values signal cables

(1) White Contact plate (2) Dry contact

7.1.3 Installing Sensor Cables

Connect the sensor cable to the corresponding ports on UIM02C. The pin definitions of the

sensor ports refer to Figure 7-3 and Table 7-2.

Figure 7-3 Pins of sensor ports

Table 7-2 Pin Definition

Silk Screen Pin Pin definition

WATER 1 12 V

2 WATER

3 GND

4 -

TEMHUM 1 12 V

2 ENV_TEMP

TP48200A-D15A1 & H15A3 & H15A5




30

3 12 V

4 ENV_HUM

TEMP1 1 TEMP1

2 GND

TEMP2 1 TEMP2

2 GND

GATE 1 DIN7+

2 JTD7

SMOKE 1 12 V

2 Smoke

BTEMP 1 Btemp1

2 12 V

7.1.4 Installing Communications Cables

When in-band monitoring is required, connect the RS485/RS232 port on the SMU to the

communications equipment over a cable with an RJ45 connector, when out-of-band

monitoring is required, connect the FE port on the SMU to the communications equipment

over a cable with an RJ45 connector, as shown in Figure 7-4.

Figure 7-4 Port on the SMU

7.2 Installing Power Cables

TP48200A-D15A1 & H15A3 & H15A5




31

Before installing power cables, ensure that all circuit breakers to the OFF position.

Do not bind the ground cable, AC power cables, DC power cales, signal cables, and

communications cable together.

Open the panel of power distribution unit, as shown in Figure 7-5.

Figure 7-5 Open the panel of power distribution unit

7.2.1 Installing DC Output Cables

Install DC output cables, as shown in Figure 7-6

CAUTION

TP48200A-D15A1 & H15A3 & H15A5




32

Figure 7-6 Installing DC output cables

7.2.2 Installing Storage Batteries and Copper Bars

Before installing storage batteries, ensure that the circuit breakers of the storage batteries

to the OFF position.

During the installation, avoid short circuits or reverse connections between the positive

and negative poles of the storage batteries. All the tools used, such as a screwdriver, must

be insulated to prevent the storage batteries from being burned and to ensure personal

safety.

Step 1 Installing the storage batteries, as shown in Figure 7-7.

TP48200A-D15A1 & H15A3 & H15A5




33

Figure 7-7 Installing two layer storage batteries

Install the copper bar, as shown in Figure 7-8.

Figure 7-8 Installing the copper bar

Step 2 Installing the power cables for storage batteries, as show in Figure 7-9.

Connect negative power cables and then positive power cables for the batteries.

CAUTION

TP48200A-D15A1 & H15A3 & H15A5




34

Figure 7-9 Installing the power cables for storage batteries

----End

7.2.3 Installing AC Output Cables

Install AC output cables, as shown in Figure 7-10.

TP48200A-D15A1 & H15A3 & H15A5




35

Figure 7-10 Installing AC output cables

7.2.4 Installing AC Input Cables

Install three-phase AC input cables refer to Figure 7-11.

TP48200A-D15A1 & H15A3 & H15A5




36

Figure 7-11 Installing three-phase AC input cables

Install single-phase AC input cables, remove the copper bar from the cable bridge on the side

panel and connect the copper bar to the AC input circuit breaker to short-circuit the breaker,

as shown in Figure 7-12.

TP48200A-D15A1 & H15A3 & H15A5




37

Figure 7-12 Installing single-phase AC input cables

Recover the panel of power distribution unit, as shown in Figure 7-13.

Figure 7-13 Recover the panel of power distribution unit.

TP48200A-D15A1 & H15A3 & H15A5

Quick Installation Guide 8 System Commissioning



38

8 System Commissioning 8.1 Installation Verification

After installation, verify that:

Step 1 The cabinet is installed properly and the cables are connected properly. (Cables fastened by screws are not easily removable.)

Step 2 Cables are arranged neatly and bound properly by using cable ties.

Step 3 The storage battery is connected properly.

Step 4 Check for short circuits between the live wires, between the live wire and the ground cable, between the live wire and the neutral wire, between the RTN+ and the 48 V busbar. Rectify short circuits before powering on the power system.

----End

8.2 Powering On and Commissioning

8.2.1 Setting Parameters

Figure 8-1 SMU panel

TP48200A-D15A1 & H15A3 & H15A5




39

(1) Running status indicator (2) Minor alarm indicator (3) Major alarm indicator

(4) Liquid crystal display

(LCD)

(5) FE (6) Locking latch

(7) Four buttons (8) USB (Reserved) (9) RS485/RS232

(10) Hold hands

If the Run indicator (green) on the SMU panel is blinking and the LCD is on, the SMU is powered on

successfully.

Button Description

Button description of SMU panel as shown in Table 8-1

Table 8-1 Button description of SMU panel

Button Name Description

or upordown Allows you to view menu items and set the value of a menu item by pressing or .

Cancel Returns to the previous menu without saving the

settings of the current menu item.

Enter Enters the main menu from the standby screen,

enters a submenu from the main menu, or saves the

settings of a submenu item.

Remark:

After a menu is displayed, the standby screen is displayed and the LCD screen becomes dark if you do not press any button within 5 minutes.

You need to log in again if you do not press any button with 8 minutes.

The preset username is admin and the preset password is 001.

Setting Parameters

Step 1 Measure the voltage across the input ports of AC input circuit breakers. The voltage must range from 200 V to 240 V. The rated voltage is 220 V. If not, ask professionals to rectify the

fault.

Step 2 Switch the AC input circuit breaker to the ON position, measure the voltage between L wiring and N wiring terminal. The voltage must range from 200 V to 240 V. The rated voltage is 220

V.

Step 3 Set the NetEco Main IP, NetEco Bak IP, NetEco Port, LUI Language and Set Time Zone according to actual conditions.

NOTE

TP48200A-D15A1 & H15A3 & H15A5




40

Step 4 Set the Qty of Battery, Rated Capacity, Set Date and Set Time according to actual conditions. (Always set Qty of Battery to 1 and set Rated Capacity to the total capacity of all

battery strings.)

Step 5 Set the IP Address, Subnet Mask and Default Gateway according to actual conditions.

Table 8-2 Parameter settings

Main Menu

Second-Level Menu

Third-Level Menu

Fourth-Level Menu

Default Value

Settings Comm Para NetEco Main IP - -

NetEco Bak IP - -

NetEco Port - 31220

Host Comm Addr 0

Comm Baudrate 9600

System Para LUI Language - ENGLISH

Set Time Zone - GMT +08:00

Quick

Settings

Qty of Battery - - 1

Rated Capacity - - 150Ah

Set Date - - -

Set Time - - -

IP Address - - 192.168.0.10

Subnet Mask - - 255.255.255.0

Default

Gateway

- - 192.168.0.1

Step 6 Set battery fuse break alarm "Enable/Disable" status.

----End

Table 8-3 Battery fuse break alarm "Enable/Disable" status

Main Menu

Second-Level Menu

Third-Level Menu

Fourth-Level Menu Set Value

Settings Alarm Setting Site Summary Battery Fuse1 Break Enable battery

fuse blown alarms

for the branches

with batteries, and

disable battery

fuse blown alarms

for the branches

Battery Fuse2 Break

Battery Fuse3 Break

Battery Fuse4 Break

Battery Fuse5 Break

TP48200A-D15A1 & H15A3 & H15A5




41

Main Menu

Second-Level Menu

Third-Level Menu

Fourth-Level Menu Set Value

Battery Fuse6 Break without batteries.

Battery Fuse7 Break

Battery Fuse8 Break

Battery Fuse9 Break

Battery Fuse10 Break



You can set parameters to modify the default mode of the Boolean value input ports and the dry contact

output ports, as shown in Table 8-4.

Table 8-4 Modify the default mode of the Boolean value input ports and the dry contact output ports

Main Menu Second-Level Menu Third-Level Menu Default Value Settings Site Summary DI1Alarm Close

DI2 Alarm Close

DI3 Alarm Close

DI4 Alarm Close

DI5 Alarm Open

DI6 Alarm Close

DO1 Alarm Act Close

DO2 Alarm Act Close

DO3 Alarm Act Close

DO4 Alarm Act Close

DO5 Alarm Act Close

DO6 Alarm Act Close

DO7 Alarm Act Close

DO8 Alarm Act Close

You can set parameters to modify the related relay of the alarm. For example, set Battery1 Lost to DO8,

as shown in Table 8-5.

NOTE

NOTE

TP48200A-D15A1 & H15A3 & H15A5




42

Table 8-5 Set Battery1 Lost to DO8

Main Menu

Second-Level Menu

Third-Level Menu

Fourth-Level Menu

Default Value

Set Value

Settings Alarm Setting Batt Summ Battery1 Lost None DO8

8.3 Powering On

To avoid damaging storage batteries, switch the battery circuit breaker to the ON positions

only after correctly setting the storage battery parameters on the SMU.

Switch the AC input circuit breakers to the OFF positions.

Step 1 Reinstall the removed copper bar or cable of the storage battery.

Step 2 Switch the storage battery circuit breakers in the PDU to the ON positions.

Step 3 Switch the AC input circuit breakers to the ON positions. Check whether the voltage between the RTN+ busbar and DC output terminal are the same as the storage battery voltage and the

voltage displayed on the monitoring unit. If not, ask professionals to rectify the fault.

Step 4 Switch the LLVD and BLVD branches to the ON positions, measure whether the voltage between RTN+ and the DC output terminal. The voltage must range from 42 V to 58 V

(without load). The rated voltage is 53.5 V. Check whether the loads work normally. If the

loads work abnormally, rectify the fault according to the relevant user guides.

Step 5 Switch the circuit breakers for the Maintenance socket, AC input, battery route, BLVD switch, and LLVD switch as required.

Step 6 Check whether the element management system (EMS) can receive the information from the power system. If not, check whether the IP address is set correctly.

Step 7 Observe the operation of the power system for 15 minutes. If no alarms (except for door alarm) are generated, and current/voltage parameters of the storage battery and loads are set properly,

then re-install the cover of the distribution unit, lock the door to the cabinet, give the key of

the cabinet door to the customer, and clean the site before leaving.

To make the system run properly, flip the switch to the Normal position.

To power on the battery forcibly, flip the switch to the BAT On position.

CAUTION

CAUTION

TP48200A-D15A1 & H15A3 & H15A5




43

----End

About This Document1 Safety Precautions1.1 Health and Safety1.1.1 Overview1.1.2 Electrical Safety1.1.3 Inflammable Environment1.1.4 Battery1.1.5 Working at Heights1.1.6 Using Ladders1.1.7 Mechanical Safety1.1.8 Bundling Signal Cables

1.2 Equipment Safety1.2.1 Electricity Safety1.2.2 Electrostatic Discharge1.2.3 Laying Cables

2 Installation Preparations2.1 Tools2.2 Installation Clearance Requirements2.3 Prepare Cables

3 ConfigurationSpecificationsInterior of the Cabinet

4 Installing the CabinetStep 1 Remove the cover of the packaging box and locate the marking-off template on the cover interior, as shown in Figure 4-1.Step 2 Fix the installation hole, as shown in Figure 4-2.Step 3 Drill holes and install expansion sleeves, as shown in Figure 4-3.Step 4 Remove the cabinet from the pallet, as shown in Figure 4-4.Step 5 Secure the cabinet on the concrete pad, as shown in Figure 4-5.

5 Installing a PGND Cable6 Installing Components6.1 Installing Rectifiers6.2 Installing a Smoke Sensor(Optional)6.2.1 Securing the Smoke Sensor6.2.2 Connecting the Smoke Sensor

6.3 Installing a Temperature and Humidity Sensor(Optional)6.3.1 Securing the Temperature and Humidity SensorStep 1 Secure the temperature and humidity sensor base to the cabinet top using two M4 mm screws.Step 2 Connect and secure signal cables of the temperature and humidity sensor to the cabinet base, as shown in the following figureStep 3 Install the top cover of the temperature and humidity sensor to the cabinet base.Step 4 The final installation view is as follows.

6.3.2 Connecting the Temperature and Humidity Sensor

6.4 Installing a Water Sensor(Optional)6.4.1 Securing the Water Sensor6.4.2 Connecting the Water Sensor

7 Installing Cables7.1 Installing Signal Cables and Communication Cables7.1.1 UIM02CAppearancePort Description

7.1.2 Installing Dry Contacts and Boolean Values Signal Cables7.1.3 Installing Sensor Cables7.1.4 Installing Communications CablesWhen in-band monitoring is required, connect the RS485/RS232 port on the SMU to the communications equipment over a cable with an RJ45 connector, when out-of-band monitoring is required, connect the FE port on the SMU to the communications equipment o...Figure 7-4 Port on the SMU

7.2 Installing Power Cables7.2.1 Installing DC Output Cables7.2.2 Installing Storage Batteries and Copper BarsStep 1 Installing the storage batteries, as shown in Figure 7-7.Install the copper bar, as shown in Figure 7-8.Step 2 Installing the power cables for storage batteries, as show in Figure 7-9.

7.2.3 Installing AC Output Cables7.2.4 Installing AC Input Cables

8 System Commissioning8.1 Installation VerificationStep 1 The cabinet is installed properly and the cables are connected properly. (Cables fastened by screws are not easily removable.)Step 2 Cables are arranged neatly and bound properly by using cable ties.Step 3 The storage battery is connected properly.Step 4 Check for short circuits between the live wires, between the live wire and the ground cable, between the live wire and the neutral wire, between the RTN+ and the 48 V busbar. Rectify short circuits before powering on the power system.

8.2 Powering On and Commissioning8.2.1 Setting ParametersButton DescriptionSetting ParametersStep 1 Measure the voltage across the input ports of AC input circuit breakers. The voltage must range from 200 V to 240 V. The rated voltage is 220 V. If not, ask professionals to rectify the fault.Step 2 Switch the AC input circuit breaker to the ON position, measure the voltage between L wiring and N wiring terminal. The voltage must range from 200 V to 240 V. The rated voltage is 220 V.Step 3 Set the NetEco Main IP, NetEco Bak IP, NetEco Port, LUI Language and Set Time Zone according to actual conditions.Step 4 Set the Qty of Battery, Rated Capacity, Set Date and Set Time according to actual conditions. (Always set Qty of Battery to 1 and set Rated Capacity to the total capacity of all battery strings.)Step 5 Set the IP Address, Subnet Mask and Default Gateway according to actual conditions.Step 6 Set battery fuse break alarm "Enable/Disable" status.

8.3 Powering OnSwitch the AC input circuit breakers to the OFF positions.Step 1 Reinstall the removed copper bar or cable of the storage battery.Step 2 Switch the storage battery circuit breakers in the PDU to the ON positions.Step 3 Switch the AC input circuit breakers to the ON positions. Check whether the voltage between the RTN+ busbar and DC output terminal are the same as the storage battery voltage and the voltage displayed on the monitoring unit. If not, ask profess...Step 4 Switch the LLVD and BLVD branches to the ON positions, measure whether the voltage between RTN+ and the DC output terminal. The voltage must range from 42 V to 58 V (without load). The rated voltage is 53.5 V. Check whether the loads work norma...Step 5 Switch the circuit breakers for the Maintenance socket, AC input, battery route, BLVD switch, and LLVD switch as required.Step 6 Check whether the element management system (EMS) can receive the information from the power system. If not, check whether the IP address is set correctly.Step 7 Observe the operation of the power system for 15 minutes. If no alarms (except for door alarm) are generated, and current/voltage parameters of the storage battery and loads are set properly, then re-install the cover of the distribution unit, ...

Documents

TP48200A-D15A1 & H15A3 & H15A5 V300R001 Quick Installation Guide 06