Upload
doankhanh
View
218
Download
2
Embed Size (px)
Citation preview
TRANSPORTATION LEARNING NETWORK NEW APPROACH TO
TRAFFIC OPERATION CENTER OPERATOR TRAINING
Dr. Peter T. Martin
Piyali Chaudhuri
Ivana Tasic
Milan Zlatkovic
Tristan Pedersen
Department of Civil & Environmental Engineering
University of Utah
September 2011
Disclaimer
The contents of this report reflect the views of the authors, who are responsible for the facts and accuracy
of the information presented herein. This document is disseminated under the sponsorship of the
Department of Transportation, University Transportation Center program, in the interest of information
exchange. The U.S. Government assumes no liability for the contents or use thereof.
North Dakota State University does not discriminate on the basis of age, color, disability, gender expression/identity, genetic information, marital status, national origin, public assistance status, sex, sexual orientation, status as a U.S. veteran, race or religion. Direct inquiries to the Vice President for Equity, Diversity and Global Outreach, 205 Old Main, (701)231-7708.
TABLE OF CONTENTS
1. INTRODUCTION ................................................................................................................................ 1
2. BASIC TRAINING .............................................................................................................................. 3
2.1 Background ...................................................................................................................................... 3 2.2 Basic Training Program .................................................................................................................... 3 2.3 Additional Basic Training .............................................................................................................. 10
3. ADVANCED TRAINING .................................................................................................................. 15
3.1 Background .................................................................................................................................... 15 3.2 Advanced Training Module ........................................................................................................... 16 3.3 Advanced Training Material .......................................................................................................... 17 3.4 Additional Advanced Training ...................................................................................................... 20 3.5 Advanced Operators’ Performance Measuring .............................................................................. 23
4. TRANSPORTATION LEARNING NETWORK............................................................................ 27
4.1 How to Access TLN....................................................................................................................... 27 4.2 Taking Classes on TLN ................................................................................................................. 28 4.3 Advantages for TLN Users ............................................................................................................ 35
5. RESEARCH EVALUATION ............................................................................................................ 37
6. CONCLUSIONS ................................................................................................................................. 39
7. REFERENCES ................................................................................................................................... 41
LIST OF FIGURES
Figure 2.1 Roads by Classification .......................................................................................................... 6
Figure 2.2 Local Map .............................................................................................................................. 7
Figure 2.3 Image from CCTV to Determine Camera Orientation ........................................................... 8
Figure 2.4 Introduction of TOC Functions for New Operators ............................................................. 11
Figure 2.5 Transportation Introduction ................................................................................................. 12
Figure 2.6 Traffic Theory and Levels of Service .................................................................................. 13
Figure 3.1 Levels of Operator Performance .......................................................................................... 16
Figure 3.2 Curriculum for Advanced Training ...................................................................................... 17
Figure 3.3 Customer Service – First Impressions .................................................................................. 18
Figure 3.4 Cross-Section ....................................................................................................................... 19
Figure 3.5 Good Operator Progression through Advanced Training..................................................... 20
Figure 3.6 Valley Emergency Communicating Center – Part of TSM .................................................. 21
Figure 3.7 One of the Lecture Slides from the Introduction to MUTCD .............................................. 22
Figure 3.8 Introducing Operators to UDOT CMS Message Format ..................................................... 23
Figure 3.9 Basic Level Checklist ........................................................................................................... 25
Figure 3.10 Evaluation of the Geometric Design Course ........................................................................ 26
Figure 4.1 Login Access to Transportation Learning Network Course Material .................................. 28
Figure 4.2 The Example of Training Material Content on TLN ........................................................... 29
Figure 4.3 TLN Lecture Slides – Standard View .................................................................................. 30
Figure 4.4 TLN Lecture sSides – No Sidebar Menu ............................................................................. 30
Figure 4.5 TLN Lecture Slides – Only Slides View .............................................................................. 31
Figure 4.6 Sidebar Options in TLN Lectures ........................................................................................ 31
Figure 4.7 Standard View of the Navigation Bar for One of the TLN Presentations ............................ 32
Figure 4.8 TLN Lecture Slide – Additional Buttons for Playing the Lecture Slides ............................ 33
Figure 4.9 Attachment Options in TLN Presentations .......................................................................... 33
Figure 4.10 An Example of the Quiz Results from TLN Lecture ........................................................... 34
Figure 4.11 Glossary of a TLN Lecture .................................................................................................. 35
LIST OF TABLES
Table 2.1 Operator Mission-Essential Task ................................................................................................. 4
EXECUTIVE SUMMARY
This report is a summary of work performed by the Utah Traffic Lab (UTL) to develop training
programs for Utah Department of Transportation (UDOT) Traffic Operations Center (TOC) operators.
The report includes training materials that are already in service and those additionally developed, at
both basic and advanced levels. The entire training material is now a part of Transportation Learning
Network — a new learning tool for the TOC operators presented in the final part of this report.
The basic training is designed to train operators in the basic knowledge, skills, and ability to work as
traffic operators. It was performed at the UTL and the TOC in a concise two-week training course. A
military approach is applied to develop individual training tasks for the operators. The UTL uses the
unique approach of focusing training on the regional transportation network and branching off into other
relevant topics when appropriate. The UTL found that understanding the local and regional
transportation network was the single most important factor in efficient incident management.
The advanced training program is designed to develop the knowledge, skills, and ability of traffic
operators to identify and solve advanced traffic management and operation problems encountered at the
TOC. It supports incident management instruction at the highest level and utilizes the advantages of
traffic operators who work 24/7 and continually monitor the traffic network through closed circuit
television.
Transportation Learning Network (TLN) is a new learning tool that goes beyond the existing training
programs by adding some new topics to both basic and advanced training levels. The report explains
how to use TLN and presents the benefits of online accessible training material.
This report also provides methods of training program testing and evaluation and offers a critical
overview of all training methods developed by the UTL to date.
1
1. INTRODUCTION
In the past decade, the focus of traffic operations centers (TOCs) has expanded from the implementation
of new traffic control and monitoring technologies to consideration of human factors’ roles in the traffic
management process. The importance of eliminating human error and maximizing efficiency has
increased as the problem of congestion costs becomes more serious. Even in normal traffic conditions,
TOC operators’ skills and knowledge can increase the level of safety and efficiency. During special
events and unplanned incidents in traffic, well trained and prepared operators will improve the TOC’s
response time, making delays on the network less severe. New TOCs are training oriented and aware of
the importance of operators’ role in traffic management.
This report combines new research into TOC operators’ training requirements with existing practices to
create a comprehensive learning procedure. Basic training is developed for new operators, while
advanced techniques apply to good, more experienced operators. Already existing basic training material
now deals with some additional problems, such as theory of traffic flow and queuing. Advanced training
material now includes procedures for managing traffic incidents and special events, Manual on Uniform
Traffic Control Devices (MUTCD) basics, changeable message signs (CMS) design and operation, and
other more complex topics.
The most important contribution of this report is the integration of both existing and new material into a
new learning tool called Transportation Learning Network (TLN). The main difference of TLN from
previous training approach is a complete online access to training course material. The new online course
is easier to use, offers the possibility of testing the trainees, and makes a good background for further
training of advanced operators. The greatest advantage is the possibility to acquire theoretical knowledge
and prepare for further training levels in classroom-independent environments. The UTL has had its own
site for these purposes, but TLN operates in a much more sophisticated and user-friendly manner.
2
3
2. BASIC TRAINING
This section explains what is currently being done to train new employees and what additional changes
have been made to improve basic training. This section also contains approaching methods used in the
training module.
2.1 Background
The basic training already in service and created by UTL was established in order to bring improvements
to two areas: defining critical operators’ tasks and the method of training. The first area of improvement
determines a finite list of operator tasks, relevant to the UDOT TOC that can realistically be taught in a
two-week operator course. The second area of improvement is related to the best method of acquiring the
necessary operators’ skills in a confined period of time.
UDOT TOC operators’ training was relying on so-called “on the job” training (OJT). Unfortunately, this
method results in inconsistent competence of newly hired operators. It also degrades the TOC’s ability to
manage the transportation network as seasoned operators must be removed from the control room to train
the new hires. The essential problem, with UDOT TOC operator training is that it is neither structured nor
evaluated. A structured training program is needed to ensure all topics are covered. Items taught during
OJT are often seen once and then forgotten, and there is no checklist of items for new hires to be trained.
The second problem with OJT is that it has not been quantified by evaluation prior to beginning work.
There was a gradual level of increased responsibility as the new operator is allowed to operate
independently, but there is no evaluation of abilities at the conclusion of training. Such evaluations are
critical to provide a “check on learning” that ensures all topics have been trained to an expected standard.
2.2 Basic Training Program
The existing basic training is developed with a military approach and an emphasis on understanding the
transportation network.
Military Approach Applied to Training
A military approach is used because the development of operators’ tasks is poorly defined in the available
transportation literature. The US Army is a highly-structured and well-trained organization where training
of new employees has been refined to a very high level. This is why the UTL applied a similar approach
to operator training at UDOT TOC. Using the existing UDOT TOC mission statement, the principles
from the cornerstone of the Army’s training program FM 7-0 Training the Force were applied to TOC
operators’ training. This concept is well-suited to TOC operator training because state DOT’s usually
have a defined mission statement but lack the structure or training program to support it. The mission of
the UDOT TOC is five-fold. It has been virtually unchanged since the inception of the TOC in 1995 with
the Department of Public Safety (DPS). It is as follows:
1. We support UDOT and DPS activities to improve highway safety.
2. We operate the highway system to provide reliable and efficient travel time.
3. We provide accurate, timely, and useful real-time traffic information.
4. We work together with other government agencies to serve the public.
5. We provide excellent customer service.
4
This mission statement is complete and directive in nature, but what is missing is the derivation of
training tasks from the mission statement. Implementing each of the statements above is only possible if
individuals are proficient at tasks that enable the statement. Beginning with the mission statement, this
study develops key operator tasks for each tenant of the statement. They are listed in Table 2.1 with the
statement they support. This mission essential task list is more detailed than a generalized job description,
but it is not overwhelmingly long. There are 22 tasks of various difficulties. While each task must be
taught using different techniques, simplifying the job into these tasks enables building the two-week
course from a list that is quantifiable but not unmanageable.
Table 2.1 Operator Mission-Essential Task 1. We support UDOT and DPS activities to improve highway safety
Communicate effectively with the UDOT complex (headquarters) and DPS operators and dispatchers
Understand the DPS’ computer automated dispatch (CAD) system; utilize it to pull real-time incident data
Understand internal processes (work orders, maintenance requests) between the TOC and other UDOT divisions
Understand and have access to current highway safety statistics, trends, and publications
2. We operate the highway system to provide reliable and efficient travel time
Understand the regional and local freeway system, surface streets, and geography
Understand the interstate highway system (numbering, signing, and impact on the local network)
Recognize local transportation trends and traffic patterns to enable more informed decision-making
3. We provide accurate, timely, and useful real-time traffic information
Operate the Commuterlink website
Operate closed-circuit television (CCTV) cameras throughout the network to enable incident detection
Operate variable message signs (VMS) throughout the network to communicate real-time with travelers
Operate the incident management system (IMS) to manage incidents and populate the Commuterlink website
Operate the 511 Traveler Information System Hotline
Operate Highway Advisory Radio (HAR)
Monitor scanners and commonly-used radio frequencies to enable incident detection at earliest possible state
Operate the remote weather information system (RWIS)
Operate the traveler advisory telephone system (TATS)
Send text updates (J-Page) on incidents to appropriate UDOT personnel
4. We work together with other government agencies to serve the public
Understand emergency procedures, such as disaster evacuations or AMBER alert, and respond appropriately
5. We provide excellent customer service
Maintain appropriate dress, appearance, and behavior at all times
Operate phone system with proper courtesies and competencies
Handle walk-in customers and group tours appropriately
Communicate with media members appropriately
5
Transportation Network – Oriented Training
The objective of this project is to develop a logical training program that teaches all concepts in the most
efficient manner possible. It is determined from observation and initial pilot training courses that the most
critical component of an operator’s knowledge is an understanding of the local transportation network.
The entire training course is built around this concept.
The term “transportation network” defines the freeway and surface street network, as well as the travel
trends, regional socio-economic factors, and geographic or topographic factors that can influence travel
patterns. Understanding this transportation network is vital to becoming a functional operator. Operators
must be able to manage cameras and variable message signs (VMSs) and understand the transportation
network. The following part of this section represents the topics covered in current basic TOC operators’
training:
Roadway design and characteristics
Regional geography
Travel trends
Software, policies, and procedures
As a result of operators not understating the larger network, the basic training module starts by teaching
operators the transportation network from a larger overview and working to a smaller, localized
understanding. This “larger to smaller” approach is applied to each major area taught: roadway design and
characteristics, regional geography, and travel trends.
Roadway Design and Characteristics
To start with the big picture of the road network, the initial classification taught is the Interstate Highway
System. We teach how the local portion of the interstate system is part of a much larger system that has
national implications for both freight movement and passenger travel. After understanding of the nation’s
highway system is achieved, operators are trained on the next “smaller” classifications, beginning with
non-interstate freeways and continuing to important U.S. and state highways, followed by principle
arterials in the urbanized areas, and finishing with local roads. Operators are taught to recognize key parts
of the highway infrastructure, particularly dangerous intersections, and basic principles of traffic flow and
signal timing. Again, operators do not need to be traffic engineers, but they should be able to
communicate with professionals in engineering language. Figure 2.1 is from the basic training module in
the road and traffic basics course. The figure is a summary of the road classification terms taught to the
new employee.
6
Figure 2.1 Roads by Classification
A unique technique to help operator trainees learn the transportation network was developed. Operators
start with sketching a map of the local system of roads on their first day of training. Drawing the map of
the local roads is repeated until operators become comfortable with the local network. Creating these map
sketches helps operators create their own “mind map” and rely on it when they hear an incident location
called out by a dispatcher. They should be able to place the incident on the map in their heads and
immediately recognize what may be happening around the incident and what else it may affect. This
proves to be the most effective technique of the entire course. Once the operator has the map of the
region visualized, it is easy to overlay cameras, signs, and other ATMS field devices onto the “mind
map.” Figure 2.2 is an example of a completed local map compared to an actual Google image of the
same area.
7
Figure 2.2 Local Map
Regional Geography – Key to Incident Management
The most important operator skill, and the most difficult for the vast majority of operators, is locating and
verifying incidents. This requires two skills that are often very difficult for operators to master – selecting
the correct camera and locating the incident on that camera. Both of these skills rely on a traffic
operator’s detailed understanding of the geography of the area.
With a good “mind map,” the ease of selecting the correct camera is largely dependent on the software
application that controls the cameras. Cameras that are named and listed logically will be helpful to the
operator. Mileposts are the most common method of labeling cameras TOC’s have focused on freeways.
Once the operator has selected the appropriate camera, understanding the area’s geography and
transportation network becomes even more important. The operator will usually have to maneuver the
selected camera, and often numerous cameras must be selected. This requires that the operator determine
where the camera they are viewing is located, where the incident is located in relation to the camera, and
the direction in which the camera is looking. Adding to the difficulty is that many initial reports are
unrefined and do not give an accurate incident location.
The knowledge, skills, and ability of operators all determine how effective they are at identifying incident
locations through CCTV. Knowing which direction the traffic is headed, as well as the geographic and
network conditions, helps experienced operators anticipate some of these problems, which will enable
them to select the correct camera quickly. Although this is a skill that often takes operators months to
master, teaching some universal methods for recognizing location and direction are very helpful in
8
developing this skill quickly in new operators. Three methods of orienting that operators are thought to
use are listed below:
Using topographical features
Using shadows and the position of the sun
Observing the road traffic (intensity, truck speed)
Figure 2.3 is an image taken from a CCTV at 2:46 PM. It displays the three methods that can be used in
determining orientation of the camera. The first method of locating the Wasatch Mountains can be used in
this image. The Wasatch Mountains can easily be located in the background of the image, and the
operator can conclude that the yellow truck is headed southbound because the Wasatch Mountains will be
east of I-15. Method 2 uses the position of the sun. In this image, the sun is in the west. The yellow truck
has no shadow on its left side, and it can be concluded that the sun is located there and the truck is in the
southbound lane on I-15. The final method of looking at the commuter trends and density is not easily
determined from this image. But it does appear that the traffic is denser in the same lanes as the yellow
truck. It can be concluded that because it is the afternoon at 5300 S on I-15, that the denser direction is
southbound and the truck is heading in that direction.
Figure 2.3 Image from CCTV to Determine Camera Orientation
9
Travel Trends
Traffic operators must be taught a basic understanding of local travel trends. This can be helpful for
identifying location and image, but it is equally important to understand the impact of an incident on the
network. Operators should understand why a similar crash in the same location will have different
impacts at 7:00 AM than it will at 5:30 PM. They also have to understand where important facilities and
businesses are located, as well as special events hosting sites. In Salt Lake City, the airport, the
headquarters of the Church of Jesus Christ of Latter Day Saints, the Utah State Capitol Building, and the
University of Utah are all population and economic centers in the city. As a result of Utah being very rich
in natural resources, there are three oil refineries, numerous rock quarries, and the Bingham Canyon
Mine, the largest open-pit mine in the world. There are also many regional distribution centers in the
western portion of the valley that lead to Salt Lake City being called the “crossroads of the west.” Traffic
operators must know the locations and general operations of these facilities to determine what type of
traffic is projected onto the network. Although they do not need to capture the detail that an urban planner
would, the operators should understand how the socio-economic characteristics of the region affect the
local traffic.
Software Programs, Policies, and Procedures
After an in-depth understanding of the network is achieved, the trainee still must learn various day-to-day
operations and programs used by operators. The UDOT TOC uses the TransSuite software package to
operate all ATMS devices and conduct incident management. These programs, as well as UDOT internal
policies and procedures, comprise the remainder of the operator course. The unique technique of teaching
operators the road network as the first subject helps them to learn the location and capabilities of ATMS
field devices.
The TransSuite package consists of four applications commonly used by operators: the ATMS map,
incident management system (IMS), traveler information system (TIS), and the video control system
(VCS). When learning these programs, the operators use them as they would in the course of managing an
incident. The standard operator procedure for incident management is:
Verify incident on camera
Post VMS sign if applicable
Create incident in IMS (populates Commuterlink website and 511)
Monitor until incident is cleared
The programs are taught in the order they are accessed, beginning with incident detection, followed by
VCS, TIS, and IMS. This order follows the same order of the standard operator procedure to help with the
training process. Initial training sessions reveal that none of the software programs are difficult to master
for the newly-hired operator. All are Windows-based and operate with familiar toolbars and functions.
New operators are trained to understand the initial incident report called out over the radio. While all
incidents called out over the radio will eventually be posted to a computer automated dispatch, it is very
important for the operator to capture all relevant information from the first radio call-out. The faster the
response to the incident, the faster the network will return to normal flow. Since the UDOT TOC is
directly linked to the highway patrol dispatch center, all traffic over the radio is in “police speak,” using
the state 10-codes and other acronyms. The relevant state 10-codes and commonly-used acronyms are
taught in the classroom, allowing the operators to identify incident locations more quickly upon beginning
work.
10
VMS messaging techniques is a dynamic subject covered in the training module. VMS practices and
standard procedures are changing as more research is done. At the TOC, TIS is the software that posts
messages to signs. More classroom time is spent on messaging theory and application than on the TIS
program itself. The training module teaches that when using a VMS message the operator must keep the
message as clear, concise, and direct as possible. Another technique asks the operator to try and rework
the message so that it conveys a clear message as if the operators themselves are on the roadway reading
the VMS message.
2.3 Additional Basic Training
The existing basic training for the new TOC operators already represents a new approach to operators’
training. Compared to the previous way TOC operators were trained, new basic training provides many
advantages. It is in-classroom-environment training, with established teaching methods, structured
approaches and organized training materials that cover critical problems that TOC operators must deal
with. The way that basic training was prepared leaves enough space to expand the training material to
other topics that are helpful for new TOC operators. The existing basic training is focused on introducing
new trainees with local roadway network. Knowledge about transportation network is the first condition
operators must meet to monitor and respond to every day and incident situations in traffic.
Additional basic training introduces trainees to some basic traffic phenomena, giving new operators a
better understanding of traffic problems they are facing. New training will include introductions to
transportation, traffic, and TOC. These additional training materials are described in the following
section.
TOC Operator Introduction
Every operator’s training should start with an introduction. The introduction is not built to be time
consuming and its nature is introductory. This part of the training should serve as a checklist or a manual
that points out the main TOC functions and traffic operators’ roles. Once new operators acquire basic
knowledge about functions they should perform, learning each of those functions in detail is much easier.
The purpose of these training materials is to inform and give operators a bigger picture of the importance
of TOC for the local transportation system.
11
Figure 2.4 Introduction of TOC Functions for New Operators
Transportation Introduction
The Transportation Introduction section of the operators’ training covers basic transportation terminology
and helps operators understand the importance of the job they are doing. It introduces them to general
definitions and activities related to all modes of transport. Some statistical facts related to how
transportation affects the economy and environment on both micro and macro-levels are included.
Challenges in terms of safety, congestion, delay, environment, energy consumption, and new technologies
are also presented.
12
Figure 2.5 Transportation Introduction
The topics covered are not directly applicable to TOC operators’ responses in different traffic conditions.
Rather, the introduction to transportation basics brings all into one — the network, the vehicles, and the
drivers — and creates a background that helps operators understand the relationships between these
elements. In this way, operators become better prepared to face potential problems on the network,
different drivers’ behaviors, and adequate response measures.
Traffic Basics
Traffic basics is the most complex part of the additional training for new operators. It introduces them to
theory of traffic flow and queuing, explaining terms such as speed, flow, density, queuing, and level of
service. In this way, operators can recognize the conditions that might lead to an incident and will pay
more attention to certain parts of the network. If the congestion level is too high and alternate routes are
available in terms of capacity, operators might consider rerouting traffic to prevent delays.
13
Figure 2.6 Traffic Theory and Levels of Service
Also introduced in the traffic basics section of the training material is traffic signal timing jargon. In case
of a serious traffic incident, even if new operators are not primarily responsible for a response, their basic
knowledge about traffic signals might be of great help to advanced level operators.
These new topics are added to the existing TOC operators’ training to help operators understand the
complexity and the importance of their role and the entire TOC role for local transportation. The new
training material enables new operators to recognize the areas of potential problems in traffic and make
them better prepared for their responses. Both existing and additional training contain quizzes so that
operators can be tested as soon as they are finished with their learning. The existing material is updated to
match the new topics, and everything is presented on the Transportation Learning Network (TLN) – a
new training tool that will be explained in details in the final section of this report.
14
15
3. ADVANCED TRAINING
Various levels of training at a TOC help to retain and increase the knowledge and ability of employees.
Training research and programs have recently focused on two areas. The first area is finding and training
of new employees (11). The second area is training for large emergency management scenarios, such as
city evacuation or terrorist response (12, 13, 14, 15). The emergency response training is built by federal
agencies and done as a need-based training program.
After creating the basic training program for UDOT TOC operators, the UTL has built an advanced
training program as the second area of operators’ training. This section describes the purpose of advanced
training and key points to include in training when implemented. Some additional topics for advanced
training material are also presented.
3.1 Background
The levels of aptitude are as follows:
Entry level operators are new employees with no prior work experience in TOCs. Training for
entry level operators includes the new employee or basic training which can take up to two
weeks.
A full performance level operator should be able to carry out his or her responsibilities with a
minimum of supervision, guidance, and direction (9). Training to reach full performance is
accomplished through recurrent training commonly given to operators in the form of monthly
meetings or instruction from other operators over a period of one to two years. This level includes
skills of network monitoring.
A good operator is an operator who can perform all the capabilities and duties of a full performance level
operator. The capabilities of a full performance level operator may include managing multiple incidents
at once; using all ATMS software effectively; understand all interchanges; reporting emergencies on
511/website; communicating with invested partners; working with no supervision; implementing special
event signal timing plans; filling a work order; issuing a J-page; using TATS, etc.
Advanced training is presented as a specific training program with the purpose to develop and use the
opportunities available to traffic operators. This is accomplished by training operators to identify and
solve advanced transportation management and operation problems. Important components of the
advanced training procedure are as follows:
Define a “good operator” and prepare for the advanced training.
Introduce a specific curriculum that develops the necessary knowledge, skill, and ability to
identify and solve advanced transportation management and operation problems.
Suggest a method for measuring the performance of the operator on the knowledge, skill, and
ability gained from the curriculum.
This report also proposes that a specific advanced training program can increase the capabilities of good
operators to identify and solve advanced transportation management and operation problems. It defines
the separate components of the advanced training program, including the definition of good operators, the
specific curriculum, and ways to measure operator performance of the curriculum and learned
capabilities.
16
3.2 Advanced Training Module
The advanced training module that the UTL has created defines the entire training procedure, from
choosing the operator who qualifies for the advanced training to completing the entire training.
To determine what a good operator is, the description of a traffic operator and the different levels of
aptitude must be defined. A traffic operator is described in Guidelines for TMC Transportation
Management Operations Technician Staff Development (9).
“A Transportation Management Operations Technician is a person who is capable of
working a typical shift in a Transportation Management Center (TMC). A typical shift
may include operation under congested, non-congested, incident and non-incident
conditions. The operator’s work will usually consist of direct, “hands-on”
accomplishment of tasks necessary to deliver one or more accepted TMC functions. An
operator must also be able to show competent knowledge, skill, and ability.”
Not all full performance level operators are considered good operators or are good candidates to receive
the advanced training program. There are other traits shown by the operator that help to determine good
candidates. Some key traits that have been identified include what the operator does in his/her spare time,
the operator’s attention to detail, and a general interest shown in traffic and the TOC by the operator.
Good operators help TOCs run smoothly in their duties to manage and control traffic in a transportation
network. A good operator may start to receive more responsibilities because he/she shows the knowledge,
skill, and ability to accomplish all duties and tasks given in prior training. Figure 3.1 shows the process an
operator follows to reach the advanced aptitude level. An operator who seeks to reach the advanced level
must be fully capable in all the duties and tasks at each previous level. Other preparation in receiving
advanced training is that an operator must show an ability to work with others and take interest in
situations that are beyond the entry and full performance level tasks and duties. Some situations may
include an operator notifying supervisors of areas of congestion at non-peak hour times or an operator
suggesting better camera locations to supervisors.
Figure 3.1 Levels of Operator Performance
Understanding the traveler information procedures is also an important part in preparing to receive the
advanced training program. A one-hour recurrent training course can effectively teach the traveler
information procedures of 511, TATS, emergency alert, Highway Advisory Radio, and IMS as related to
traveler information.
New
Employee
Basic Training Recurrent Training
(monthly meetings)
2 weeks
Entry
Level
Full Performance
1 – 2 years
Advanced Training Advanced
Level
17
3.3 Advanced Training Material
A specific curriculum that helps good operators develop the necessary knowledge, skills, and ability is an
essential part of the advanced training program. The curriculum is designed to teach them to identify and
solve advanced problems that other TOC employees, specifically engineers, handle. The curriculum is
divided into three different courses to accomplish this goal. Figure 3.2 shows the divisions with the
subjects addressed in each course.
Figure 3.2 Curriculum for Advanced Training
A structured curriculum will help TOCs meet the overall goal to develop valuable employees, monitor the
transportation network, and identify and solve transportation problems. The curriculum presented will
help good operators obtain the specific capabilities to perform many of the responsibilities that are given
to them. The capabilities that an advanced level operator should be able to complete are:
Handle difficult phone calls
Respond to HAZMAT
Fix broken traffic signal timing
Identify all road elements and calculate superelevation
Lead/Train other employees
Understand traffic flow theory
PeMS – Report delay times
Manage work zones
Manage ramp meters
Advanced Operator Techniques
The first course in the advanced training curriculum is called advanced operator techniques. An operator
who has received basic training and reached the status of a good operator should be able to understand the
transportation network and use the advanced transportation management system software effectively and
efficiently. This course adds upon the full performance level by providing advanced customer service
skills, knowledge to respond to atypical traffic crises, and the skills to manage traffic signals. The
advanced operator techniques course develops the capabilities of good operators to identify and solve the
advanced transportation problems in operations.
The interaction between the operators and the public and media, often referred to as customer service, is
the first subject covered in the advanced operator technique course. This interaction improves upon the
full performance level and helps develop capacities for the daily task. TOCs are information centers; they
monitor the conditions of the transportation network and have access to all DOT agencies. To make use of
Advanced Operator Techniques
• Customer Service
• Atypical Events
• Traffic Signals
Geometric Design
• Cross-section
• Road Elements
• Curves
Traffic Flow
• Basics of Traffic Flow
• PeMS
• Vehicle Detection
18
the information, the TOC provides a direct phone line to the operators that they are required to answer
during their shift. This means that part of the traffic operator’s job is to answer phones and use customer
service techniques to successfully provide the information to both the public and the media. The
customer service aspect of the traffic operator’s duties can create challenges and must be handled
appropriately. Handling the challenges of customer service and phone etiquette are addressed in the
course. Figure 3.3 describes how an operator can create a good first impression on the phone and how
they will be evaluated. Operators are taught to be polite, informative, and professional. The qualities that
are needed for good customer service skills include listens well, gives verbal feedback, uses the caller’s
name, and works to provide immediate feedback. These qualities are emphasized in the training.
Figure 3.3 Customer Service – First Impressions
Operators are also taught to respond to atypical or emergency situations and what their responsibilities are
and what actions they should take in these cases. An atypical situation is defined as any severe weather
hazard or HAZMAT incident. These incidents are usually given with little to no warning and require the
operator to seek supervisor help to resolve them.
The final subject covered in the advanced operator technique course is how to use the traffic signals at an
operator level. Developing and managing traffic signal timing plans is not the responsibility of the traffic
operator. However, understanding how to use the traffic signal software and how to implement created
planes can be an asset for the operators. Operators may be taught how to implement a signal plan, how to
deal with signal software in non-working hours, and how to understand the basics of signal timing plans
and identify the problem areas.
19
Geometric Design
Geometric design is the understanding of the road itself, the cross-section, road elements, and curvature.
Understanding the road will help operators understand if problem areas are user related or a condition of
the geometry of the road. Operators study the road looking for traffic incidents. After the geometric
design training, the operators will begin to look for geometric design problems as they look at the road.
The geometric design course is focused on the identification of advanced transportation problems. The
primary goal of introducing this course is to increase operators’ awareness of traffic safety issues. Figure
3.4 is a slide taken from the geometric design course. This figure is describing the elements that are taught
in the cross-section subject.
Figure 3.4 Cross-Section
Theory of Traffic Flow and Queuing
Theory of traffic flow and queuing is an update of the course “Traffic Basics” from the basic operators’
training. It is essentially the same material adjusted for advanced level operators and brought into the
advanced training for the purposes of traffic incident management. FHWA defines traffic incident
management as a systematic, planned, and coordinated use of human, institutional, mechanical, and
technical resources to reduce the duration and impact of traffic incidents and improve the safety of
motorists, crash victims, and traffic incident responders. Having an understanding of capacity, flow, and
20
demand, the basic elements of traffic flow, helps operators see how efficiency in traffic incident
management can benefit the travel time of the users.
Just as the basic level course, traffic flow covers definitions of speed, flow and density, but goes even
further explaining mathematical relationships between these values. Advanced operators are also taught
levels of service, but the course is expanded with basic definitions from the shockwave and queuing
theory. This should help operators to better understand and deal with the problems of bottlenecks on the
transportation network. A special part of the course is dedicated to queuing theory application in
modeling traffic flow interrupted by incidents.
Performance Measurement System (PeMS), software that collects data on the freeway system in Utah, is
also introduced in this part of the training. The speed and flow data that this software collects can be used
to determine the trends that occur due to recurrent and non-recurrent congestion. This software can also
be used to determine the delay time that an incident can cause. The training for this subject consists of
learning how to use the software and how to calculate delay times.
The final subject covered in the traffic flow course is an introduction to vehicle monitoring technologies.
This subject helps operators understand how and from what sources TOCs get their traffic flow data. This
subject introduces six different vehicle detection methods and explains what information they provide.
The advanced training curriculum delivers the necessary information to develop the knowledge, skill, and
ability to prepare good operators to work at the advanced level. Figure 3.6 illustrates the process to attain
the advanced level. The curriculum should be given in a two-week period, but it does not automatically
qualify operators as advanced. A measure of how well the operator can apply the information needs to be
determined six months to a year after the training. This will allow enough time for operators to master the
information taught in the advanced training curriculum.
Figure 3.5 Good Operator Progression through Advanced Training
3.4 Additional Advanced Training
Advanced operators’ training offers more opportunities for the expansion of training material. The newly
presented topics and problems are concerned with transportation system management, traffic engineering
studies, Manual on Uniform Traffic Control Devices (MUTCD) and Changeable Message Signs.
Advanced operators are getting the opportunity to learn more about efficient use of the available road
capacity, traffic data collection, traffic control in different traffic conditions, and advanced traveler
information systems.
Full Performance Level Operator
Advanced Training Program
Advanced Level
Operator
Good Operator
Shown interest in more responsibilities
More responsibilities
6 months – 1 year
2 weeks
21
Transportation System Management
The objectives of this module are to introduce the benefits achieved through transportation management.
Transportation Systems Management’s (TSM) purpose is to create more efficient use of existing facilities
through improved management and operation of vehicles and the roadway. Focus is put on changing the
facilities and how people use them through the implementation of TSM strategies and new information
technologies.
Advanced operators should learn how to create and efficiently use road space in congested environments.
They learn how to deal with increased traffic volumes and how to manage transportation supply and
demand. Helping to provide and improve transit service is also one of the assets advanced operators
should possess.
This course brings together geometric design of the roadways and traffic operations. It enables operators
to combine the knowledge they have about capacity and level of service with the knowledge and skills in
the area of TOC equipment and technologies deployment.
Figure 3.6 Valley Emergency Communicating Center – Part of TSM
Additional way of improving efficiency, including dedicated bus lanes, carpool lanes, and reversible
lanes, are also introduced here. Besides managing the roadway capacity, operators get the freedom to
coordinate different modes of transport to minimize traveler delays. The course prepares operators to
manage parking problems, increase the size of pedestrian zones, and not only make traffic more efficient,
but also safer for the users.
22
Traffic Engineering Studies
This course introduces the basic principles of traffic engineering studies for DOT personnel lacking civil
engineering backgrounds. It includes speed, volume, travel time, delay and parking studies.
Speed studies will help operators understand how speed data is collected and how speed is distributed in
the traffic stream. In this way, operators are enabled to make speed related decisions.
Volume studies introduce some very important terms such as average daily traffic, peak hour volume,
vehicle miles traveled. Travel time and delay studies enable operators to understand how to calculate
average traveler delay based on the available volume data.
Finally, some basics about parking studies are presented in this course with the purpose to inform
operators about the terminology used in the area of parking management. Like every other course in the
training, quizzes test operators’ knowledge on this topic.
MUTCD Basics
Although MUTCD basics is a newly added topic, it is very important for advanced level operators. The
objective is to introduce operators to MUTCD contents and its applications in practice. MUTCD defines
national standards for all traffic control devices: signs, signals, markings and other devices. TOC
operators work with these devices every day, whether they monitor or need to change the existing traffic
control. It is critical for them to know how to apply standards from MUTCD.
Figure 3.7 One of the Lecture Slides from the Introduction to MUTCD
23
The course first explains the form in which MUTCD is written: standard, guidance, option, and support.
Then each of nine chapters from MUTCD is presented so that operators become comfortable with the
manual and it is easier for them to use it when needed. Finally, applications of MUTCD are presented
with practical examples.
Changeable Message Signs
The first traveler information tool that TOC operators use to reach the drivers in traffic is Changeable
Message Signs (CMS). The most critical part of operating CMS is posting adequate CMS messages. The
area of CMS messaging is still new for the researchers, and methods of CMS application are constantly
updated as new information becomes available. MUTCD has its own section dedicated to CMS, and
every state DOT has its own rules of CMS messaging based on MUTCD standards.
The operators are first introduced to the importance of the role that CMS have in traveler information
systems. CMS are the fastest way for TOC operators to directly inform travelers about traffic conditions.
Then different types of CMSs in terms of application, size, and location are defined.
Figure 3.8 Introducing Operators to UDOT CMS Message Format
The essential part of the course is dedicated to CMS message design. Operators learn what types of
messages are unacceptable for the drivers. The purpose is to enable operators to understand how drivers
are receiving CMS information. Operators are taught to create clear and concise messages that drivers can
read and understand in the amount of time they have while in traffic. If the message is poorly designed, it
might create confusion among drivers and worsen traffic conditions instead of helping to deal with
possible delays and incidents. Standards for message length, characters’ size and visibility distance are
provided as minimum criteria that need to be respected based on MUTCD and other available literature
from this area. Before testing the operators’ knowledge at the end of the course, some examples of CMS
messages with design considerations are provided for the training.
3.5 Advanced Operators’ Performance Measuring
The final component of the training is to suggest a method for measuring the performance of the operator
about the knowledge, skill, and ability gained from the curriculum. Performance measuring is the process
of identifying current knowledge, skill, and ability and determining how well the trainees learned the
24
training and how effective they are at applying the training. Performance is measured on how well
operators can perform their capabilities, including identifying and solving advanced transportation
management and operation problems. Three additional publications are used to help in the formulation of
this specific performance measurement system, two from FHWA (16, 17) and one from the
Transportation Research Board (18).
The performance measures are a balance of quality and quantity. The quality of the performance measures
should be comprehensive enough to assess the knowledge, skill, and ability — both of what is already
known and what is taught. The quantity of the performance measures is assessed to assure that the
evaluation does not become too cumbersome. The result from the performance measuring also needs to
provide a way to help revise and improve training service, quality, and productivity.
The quality of the performance measures can be evaluated against the Kirkpatrick Four Level Model of
training evaluation (10). This ensures that the assessment and evaluation processes will accomplish their
purposes of helping the operator understand the training and retain the information.
1. Student reaction – “What they thought and felt about the training.”
2. Learning – “The resulting increase in knowledge or capability.”
3. Behavior – “The extent of behavior and capability improvement and implementation and/or
application.”
4. Results – “The effect on the environment resulting from the trainee’s performance.”
With the new method of measuring performance developed for the advanced training, both assessment
and evaluation methods are used. The performance measuring for the advanced training gives an
assessment of current employee levels through a checklist method. Next, an evaluation of the advanced
training is given to the trainee, consisting of short answer and problem solving questions. Finally, the
frequency and duration of the performance measuring is presented.
Assessment through Checklist
The assessment of current operator knowledge, skill, and ability levels is developed in the research and
given by the operator’s supervisor. The checklist is modeled after the generic activity groups presented in
the staff development FHWA publication (9). Three checklists are available for the basic, full
performance, and advanced levels. The checklists follow the quality and quantity guidelines, and limits
the number of performance measures to no more than ten specific areas of assessment. The checklists are
valuable in finding the strengths and weaknesses of each operator and allow the supervisor to focus on the
development of the operators. The checklists follow the capabilities so that the supervisor and operator
know exactly what the expected performance should be.
The basic level checklist measures the knowledge, skills, and ability of an operator after the basic training
and two full weeks of on-the0job experience. The areas are measured by marking if the operator achieves
certain capabilities as shown in Figure 3.9. The three levels of capability are not capable, needs work, and
fully capable. The areas of assessment for the basic level are hearing incident/using radios, create correct
VMS signs, create an incident on IMS, select/orient cameras, Salt Lake geography, overall geography,
communication with other operators, reading CAD system, willingness to learn, and productive during
down-time.
25
Figure 3.9 Basic Level Checklist
The full performance level checklist is given to an operator six months to a year after the basic level
performance is achieved. The full performance level is the level at which an operator can work an entire
shift and do the day-to-day tasks without supervision. The areas of assessment for the full performance
level are:
manage multiple incidents at once
use all ATMS software effectively
understand all interchanges
reporting emergencies on 511/website
communicate with invested partners
work with no supervision
implement special event signal timing plans
fill a work order
issue a J-page
use TATS
The advanced level checklist is given to the employee after the advanced training and after a month of
using the knowledge and skills that were learned. The areas of assessment for the advanced level are:
handle difficult phone calls
HAZMAT response
fix broken traffic signal timing
identify all road elements
calculate superelevation
leadership/train other employees
understanding of traffic flow theory
PeMS – report delay times
work zone management
ramp meter management
26
Evaluation after Training
Evaluation or testing of the employee after training is critical to determine what was learned and how
capable the employee is of applying the training, specifically in identifying and solving engineering
problems. The following steps are used in creating the evaluation for advanced training. The information
is from the FHWA Handbook for Developing a TMC Operations Manual (17).
1. Identify the critical activity.
2. Identify the goals and objectives of the activity.
3. Develop a set of candidate performance measures.
4. Identify performance targets.
5. Compare actual performance to targeted goals.
6. Determine corrective actions or progress needed to achieve goals.
The critical activities or tasks are identified for each course in the curriculum. These tasks are then
compared to the goals of the training. The questions are then created to both help employees apply the
tasks that are learned and fulfill the goals set in the training. The number of questions for each course
follows the quantity and quality guidelines. The questions evaluate the employee’s understanding in ten
questions.
Two techniques are used in the evaluation: short answer and problem solving questions. The two
techniques are used because of the two methods in how information is retained. The short answer
evaluates the operator about what he/she remembers from the training. These questions are often easier
and can appear multiple times. This method of learning uses short term memory recall and repetition.
Problem solving questions require more thought and the actual application of the principals taught in the
training. The problem solving technique uses the critical thinking method of learning. Figure 3.10 is an
example of the short answer and problem solving questions.
Figure 3.10 Evaluation of the Geometric Design Course
27
4. TRANSPORTATION LEARNING NETWORK
The Transportation Learning Network (TLN) is a distance learning partnership among organizations in
the western United States. TLN links together the transportation departments (DOTs) in North Dakota,
South Dakota, and Wyoming and the Mountain-Plains Consortium universities of Colorado State
University, North Dakota State University, South Dakota State University, University of Utah, and
University of Wyoming.
TLN’s mission is to support quality transportation through a network of people and technology that serves
TLN members by enhancing communication, education, professional development, technology transfer,
and research.
As mentioned in the beginning of this paper, what the existing TOC operators’ training was missing an
advanced and organized tool that can deliver both basic and advanced training material in a user-friendly
manner. TLN makes this goal realistic using sophisticated presentation software Articulate to combine
learning and testing material into a final distance learning product. The greatest advantage of this type of
learning approach is accessibility of the training material. TLN does not require classroom presence for
the theoretical part of the training. This makes the preparation for practical training exercises much more
convenient for the operators. TOC operators can read or hear their lectures at home, test their knowledge
using the quizzes at the end of each course, and proceed to the in-classroom training at the UTL.
4.1 How to Access TLN
TLN provides an e-learning possibility for new TOC operator training. This means that trainees have
constant online access to training material. When the users want to access the course material, all they
need are credentials to log in. The access is allowed through the following link:
https://ugpti.rapidintake.com/.
After they receive the credentials, users can test the course material. This kind of course access gives
more freedom to schedule the operators’ training and makes the theoretical part of the training more time
and space independent. Distance learning allows trainees to adjust this part of the training to their own
schedule. It also allows the teachers to update the training material and grade the trainees. When it comes
to grading, this kind of learning provides a very clear grading system, same for all trainees, with the
instant possibility to see the results of their work. All trainees do not have to take the class at the same
time, but it is possible for the teachers to establish some time limits. The basic concept is to make a great
part of the training more convenient for both trainees and teachers.
At the same time, distance learning allows the option of separating the trainees who are taking online
courses from those that have classroom training. Only trainees that complete online training are allowed
to continue to the classroom and test their knowledge on practical problems. In this way the capacity of
the classrooms is used more efficiently and only for the purposes of practical training related to traffic
monitoring, incident management, traveler information systems, and other traffic operation activities.
Figure 4.1 represents a screenshot of an access attempt to TLN training material.
28
Figure 4.1 Log in access to Transportation Learning Network Course Material
4.2 Taking Classes on TLN
TLN training is based on animated presentations built in software called Articulate. The software uses
PowerPoint as the main development environment and overlays interactions, audio, and flash media.
Then, it exports it out into a handy, single file for distribution on the web. What sets this e-learning
solution apart from many other of its competition is the ease of use. Articulate combines video and audio
effects and allows the possibility of having a narrator who gives the lecture. This learning software also
has the ability to handle questions. It has a range of built-in question-handling options with various
question types. The software is produced by educational experts, and its purpose is to make e-learning
environments comfortable for the users.
Once operators have accessed the TLN, the list of possible training lectures will open. Trainees can access
lectures by clicking on the title or using the option “search” at the top of the screen. Each lecture file has
the following information:
ID number
Lecture title
Date when the lecture is posted
Date when the lecture is due
Lecture status
An ID number at the beginning of each lecture file does not concern the trainees. It is for organizational
purposes and will be used by teachers only.
A lecture title provides information about the lecture topic, and trainees and teachers can access the
training material by clicking on the lecture title.
The date when the lecture is posted is also for the purpose of organization and is used by teachers when
updating the course material.
The date when the lecture is due is important for the trainees because it tells them when the lecture needs
to be completed. To complete the lecture, trainees need to read and listen to the learning material and
submit the quizzes at the end of the presentation.
29
The status of the lecture has two options:
For trainees: Open / Closed
For teachers: Open Complete
If the trainees see that the lecture status is “open,” the lecture is open for them to access. If the status is
“closed,” then the trainees cannot access the lecture. When teachers log in they will either see status
signing ”open” or “complete.” When the teacher sees status “open,” that means the lecture can be updated
and changed. When the teacher sees status “complete,” the lecture is closed for updates and changes.
Figure 4.2 shows an example of training material content available for trainees’ access on the TLN.
Figure 4.2 The Example of Training Material Content on TLN
After choosing one of the lectures opened for access, the trainee may start the learning process. The
lecture will be opened, and trainees can use the button on the right side of the bottom of the screen to
access the standard view, no sidebar view, or slide only view menu (see Figures 4.3-4.5).
30
Figure 4.3 TLN Lecture Slides – Standard View
Figure 4.4 TLN Lecture Slides – No Sidebar Menu
31
Figure 4.5 TLN Lecture Slides – Only Slides View
The side menu serves as navigation. It is one of the options that software Articulate offers, making these
presentations so user-friendly. This navigation tool provides the option of skipping the slides that the
learner does not want to see and going directly to the slides that they are interested in seeing. The new
slides will load fast, which is also one of the advantages of this software.
Figure 4.6 Sidebar Options in TLN Lectures
32
As shown in Figure 4.6, the side menu offers several options:
Outline
Thumbnails
Notes
Search
The option “outline” provides the list of all main topics covered in the lecture. This also makes trainee’s
orientation in the training material much easier. Option “thumbnails” allows the trainee to see every slide
in the lecture together with the name of the topic that slide belongs to. When the trainee clicks on the
option “notes,” he/she will be able to see the narrator’s text, which might make following the lecture
easier for those who see the material for the first time. Finally, option “search” in the side menu provides
the opportunity to find the particular word/group of words in both slides and lecture notes.
For those trainees who are working in this environment for the first time, TLN provides the instructions
on how to use the navigation bar at the bottom of the screen. Figure 4.7 shows how to manage the
volume, how to play and stop the slides, how to change the playing slides, and the attachment option.
Figure 4.7 Standard View of the Navigation Bar for One of the TLN Presentations
Figure 4.8 shows the functions of the additional buttons on the lecture slides. The red button with the
white arrow takes the trainee to the next slide when the playing of the current slide is completed. If the
trainee wants to skip the current slide and continue to the following, “back and forward” option is
available. In the final part of the lecture, when the trainee takes a quiz, there is a “submit” option that the
trainee needs to click to proceed to the next quiz question (see Figure 4.8).
33
Figure 4.8 TLN Lecture Slide – Additional Buttons for Playing the Lecture Slides
The “attachments” button at the top of the lecture slides helps the trainee to view the attached content.
Once the trainee clicks the “attachment” button, a table of contents with the scroll bar will show up. By
choosing any available topic from the attached content, the trainee is taken to the appropriate website and
can see the literature source for the chosen topic (see Figure 4.9).
Figure 4.9 Attachment Options in TLN Presentations
34
When the trainees reach the end of the lecture slides, the quiz is created to test their knowledge. Quizzes
have different question types:
True/false
Multiple response
Multiple choice
Fill in the blank
Word bank
Matching drag and drop
Matching drop-down
Sequence drag and drop
Numeric questions
“Hotspot” questions
Each question has its score posted at the bottom of the lecture slide, and trainees can see if their answer is
correct or incorrect right after they click the “submit” button. At the end of the quiz, trainees can see their
total scores and the “passing score.” The result will tell them if they have passed the test or not. If they
want to see a recap of their results, the button “review quiz” offers that option.
Figure 4.10 An Example of the Quiz Results from TLN Lecture
35
After the trainees complete the lecture and the quiz, there is an option of viewing a glossary of the entire
lecture at the end of the presentation. The glossary is organized in alphabetical order and provides the
definition for each important term used in the lecture.
Figure 4.11 Glossary of a TLN Lecture
After finishing the entire lecture, an “exit” button at the top of the slide on the right side next to the
“attachments” ends the current lecture session.
4.3 Advantages for TLN Users
What follows is a summary of benefits to TOC operators who use TLN as a new training tool:
Easy to access
Easy to use
Good slides navigation
Quick video loading
Access to literature resources
Possibility of learning and testing
Instant test results
Possibility of reviewing the taken quiz
Glossary of important terms
Well organized and well-presented lectures
An additional advantage is, as mentioned, the possibility of distance learning and a more independent
training approach.
36
37
5. RESEARCH EVALUATION
The TOC operators’ trainings provided to date have shown that different individuals require different
training treatments considering their background and experience levels. The low number of trainees make
it possible to customize the training program to the individual, a luxury many larger metropolitan areas
may not have.
While the operator course has been effective to date, some limitations still need to be addressed. One of
the largest obstacles is the confidential nature of much of the information gathered, analyzed, and
disseminated at the TOC. The UTL will most likely never have access to the CAD or radio traffic coming
from the DPS dispatch center, which is unfortunate because listening to the constant radio transmissions
and extracting relevant information is one of the most difficult, and important, skills of the operator. This
would prevent achieving a complete off-site training at the UTL.
A final limitation is that the UTL cannot train and evaluate an individual’s ability to cope with boredom.
A common description of work in an operations center is “hours of tedium interspersed with moments of
terror” (8). A recommendation is for the control room manager to consider the changing pace of the
operator job when designing work schedules and break periods.
As the advanced training program was given to operators, several questions began to arise, such
as “Does increased responsibility mean increased performance?” This question is an important one
because if no noticeable increase in performance at a TOC is seen, why implement the advance training
program? If operators correctly apply the training, then they can identify problems in the transportation
network and solve the problems from the skills gained through the training. Many practical examples
illustrate the knowledge gained in the advanced training courses where operators have managed to deal
with the problems that are usually covered by engineering level tasks: fixing signal timing, identifying
poor geometric design, etc.
The delivery of the advanced training program was another problem that was discovered in the previous
research. The new method developed using TLN is created to improve the teaching and learning
efficiency. When it comes to the practical part of the training, UTL is now equipped to train new
operators in transportation network monitoring. Starting in 2011, the UTL has access to UDOT TOC
traffic cameras, and this provides a realistic TOC environment in the UTL classroom. New operators will
be able to learn how to find traffic incidents in real time and outside of UDOT TOC. In this way,
employed TOC operators won’t be bothered with the training and new operators will be prepared to
respond to traffic incidents as soon as they start their job in the TOC.
The benefits these training programs provide to the public include that certain problems can be fixed any
time of the day by advanced level operators, and congestion can be reduced by identification of poor
design. The benefits to a TOC are that problems can be identified by observation of unusual congestion
and TOCs will have more qualified employees in their workforce. Finally, advanced training can benefit
operators by increasing the competency and responsibility at TOCs.
The advanced training program is a specific program that will help direct TOCs in the advancement of
their traffic operators. The training program deviates from the traditional methods of placing more
responsibilities gradually on good operators. Instead, it focuses on a structured training method that
prepares operators to identify and solve advanced problems and to share the results with other TOC
employees. The advanced training program is recommended to TOCs who have 24 hour, seven day a
week, transportation monitoring operators.
38
The recommended delivery method for the advanced training program is an interactive training program
from a web-based program or CD. The benefit of having a completely electronic training program is that
the operator can receive training at any time. Having dedicated instructor-led training can cause the
operator to miss critical time in the control room — time needed for traffic management. This training
program can provide many benefits to help TOCs meet the demand for service to the public and provide a
reliable and efficient transportation network.
39
6. CONCLUSIONS
The basic training module described in this paper is designed to teach the necessary knowledge, skills,
and ability to new operators in a concise two-week program. Using the critical or mission-essential task
list to guide the training of new operators achieves this. Using a military-styled pedagogy helps new
operators identify which skills are most important and how to gain the knowledge and ability to perform
them. Finally, a network centered training approach is found to be the best method to teach new
employees the importance of incident management. By focusing on the geography of the area, the
operators gain the understanding of their role in traffic management.
The advanced training program is designed to train traffic operators at TOCs to identify and solve
advanced transportation management and operation problems. The program creates quality training by
providing TOCs with tools to help identify which operators are ready to take on more responsibilities and
how to prepare them for these responsibilities. The specific curriculum aids the training program by
giving direct information and training courses that are not too general and can be applied immediately.
The last element of the program suggests a way to measure the performance of operators under advanced
training.
The basic and advanced training are both designed to be delivered through TLN. This new e-learning tool
will enable operators to have trainings adjusted to their schedule. New UTL equipment will separate
operators training from using the UDOT TOC space even more, providing real-time traffic monitoring
practices. Finally, operators will be trained on realistic traffic incident scenarios to establish a higher level
of traffic incident management in UDOT TOC. Prepared training methods and materials are structured,
well organized, and presented in the manner that focuses on developing necessary knowledge, skills, and
abilities for both new and advanced TOC operators.
40
41
7. REFERENCES
1. Carvell, James D. Jr.; Balke, Kevin; Ullman, Jerry; Fitzpatrick, Katherine; Nowlin, Lewis;
Brehmer, Christopher (1997). Freeway Management Handbook. FHWA-SA-97-064, McLean,
Va.
2. Kelly, Michael J.; Garth, Jeffrey M.; Whaley, Christopher J. (1995). Comparable Systems
Analysis: Design and Operation of Advanced Control Centers. FHWA-RD-94-147, McLean,
Va.
3. Kelly, Michael J. (1999). Preliminary Human Factors Guidelines for Traffic Management
Centers. FWHA-JPO-99-042, McLean, Va.
4. Mitta, Deborah A.; Kelly, Michael J. (1996). Design of an ITS-Level Advanced Traffic
Management System: A Human Factors Perspective. FHWA-RD-95-181, McLean, Va.
5. Baxter, Daniel H. (2002). Guidelines for TMC Transportation Management Operations
Technician Staff Development. FHWA-OP-03-071, McLean, Va.
6. Gerfen, Jeff; Chu, Lianyu, and Recker, Will. TMC Simulator for Operator Training Using
Micro-Simulation. Transportation Research Board Annual Meeting, January 2008.
7. Field Manaual 7-0: Training the Force. Headquarters, Department of the Army. October 2002.
8. Transportation Management Center Concepts of Operation: Implementation Guide. FHWA-
OP-99-029, Washington, D.C.
9. Baxter, Daniel H. Guidelines for TMC Transportation Management Operations Technician Staff
Development. FHWA-OP-03-071. FHWA, U.S. Department of Transportation, McLean, Va.,
2002.
10. Training Programs, Processes, Policies, and Practices, A Synthesis of Highway Practice,
Publication NCHRP Synthesis 362. Transportation Research Board, National Research Council,
Washington, D.C., 2005.
11. Shepard, B. A Network-Focused Approach to Training Operators at the UDOT Traffic
Operations Center. Utah Traffic Lab, UTL-1207-93, December 2009.
12. Transportation’s Role in Emergency Evacuation and Reentry, Publication NCHRP Synthesis
392. Transportation Research Board, National Research Council, Washington, D.C., 2009.
13. Nakanishi, Y.J., Transportation Security Training and Education: Building Up Resources,
Techniques, and Strategies. TR News, Number 238, May-June 2005, pp. 3-4.
14. Goldblatt, R.B., and K. Weinisch, Evacuation Planning, Human Factors, and Traffic Engineering:
Developing Systems for Training and Effective Response. TR News, Number 238, May-June
2005, pp. 13-17.
15. Ozbay, K., New Frontiers in Emergency and Incident Management Training: Multiagency
Models and Interactive Simulation Systems. TR News, Number 238, May-June 2005, pp. 18-23.
42
16. Park, B., Transportation Management System Performance Monitoring. Evaluation, and
Reporting – A Technical Handbook. FHWA-HOP-07-124. FHWA, U.S. Department of
Transportation, Washington D.C., 2005.
17. Seymour, E.J., J.D. Carvell Jr., J.L. Carson, and R.E. Brydia. Handbook for Developing a TMC
Operations Manual. FHWA-HOP-06-015. FHWA, U.S. Department of Transportation,
Washington D.C., 2005.
18. Transportation Research Board Special Report 275: The Workforce Challenge: Recruiting,
Training, and Retaining Qualified Workers for Transportation and Transit Agencies,
Transportation Research Board, National Research Council, Washington, D.C., 2003.
19. www.traanslearning.org
20. ugpti.rapidintake.com