Tryton 2012 Final wo tab… · The Tryton Open Hole Centralizer is mainly used with Tryton Open Hole Packers, generally as part of the Tryton Multi-Stage Frac System. The Centralizer

Calgary -Sales/Marketing Office1100, 250 – 2nd St. SWCalgary, AB T2P 0C1

Ph: 403 263-6778

Lloydminster – Field OfficeCorporate/Accounting Office

6702-56 StreetLloydminster, AB T9V 3A7

Ph: 780 875-0800 (24hr)

Drayton Valley – Field Office5622 – 56 St.

Drayton Valley, AB T7A 0B2Ph: 780 542-7070

Edmonton -Warehouse/Tech Services

1, 6404 Roper Rd.Edmonton, AB T6B 3P9Ph: 780 468-0909 (24hr)

Estevan, SK – Field Office#7, Highway 39 East

Estevan, SK S4A 0W3Ph: 306 636-2291

Brooks – Field Office329 -9th St. E

Brooks, AB T1R OK2Ph: 403 362-8600 (24hr)

High Level – Field Office11961 – 95 St.

High Level, AB T0H 1Z0Ph: 780 926-2624 (24hr)

Grande Prairie – Field Office110, 7001 – 98 St.

Clairmont, AB T0H 0W0Ph: 780 832-0011 (24hr)

Whitecourt – Field Office3421-41 Ave.

Whitecourt, AB T7S 1N8Ph: 780 706-2555 (24hr)

Red Deer – Field Office1, 7836 – 49th Ave.

Red Deer, AB T4P 2B5Ph: 403 348-0062 (24hr)

TrytonPeople. Products. Performance.

www.trytontoolservices.com

12

Service Tools7 Plugs & Retainers89

Multi-Stage Frac SystemsRetrievable Packers

3 Seal Bore Packers4 Flow Control5 Accessories6

Tubing AnchorsMiscellaneous

Table Of Contents


Nitrile (Buna-N)

Ethylene Propylene Diene Monomer (EPR, EPDM)

This is the most common compound that is used; it has excellent resistance to petroleumproducts and fuels. The temperature range of Nitrile is -35°F - 250°F, short durations slightlyhigher. Nitrile compounds have excellent resistance to compression set or cold flow, tear andabrasion. They do not possess good resistance to ozone, sunlight or weathering; however, itcan be enhanced with additives.

Excellent general-purpose temperature range (-65°F to 350°F) elastomer with superiorresistance to water, steam, alcohol, engine coolants, sunlight and weathering. Notrecommended for use with petroleum oils or fuels. Although the rubber experts do notrecommend EPDM for use with petroleum oils or fuels, we have experienced great successthroughout the oilfields in steaming applications. We have had great success in fields in KernCounty and Indonesia with temperatures up to 450°F, when used in a steam only application.

HNBR

Viton

Aflas

Notes:

Hydrogenated Nitrile Butadiene Rubber (HNBR), also known as Highly Saturated Nitrile(HSN), is a special class of Nitrile rubber - Nitrile Butadiene Rubber (NBR) that has beenhydrogenated to increase saturation of the butadiene segment of the carbon polymerbackbone. Subsequent improvements to the material properties over that of an NBR includegreater thermal stability, broader chemical resistance, and greater tensile strength.Temperatures up to 325°F.

Compounds of Viton are rated at 400°F with short durations up to 450°F. Viton is generallyserviceable down to -18°F to -23°F. Viton has excellent resistance to oils, fuels, lubricants,and most mineral acids. It has extremely low permeability to a broad range of substances. Itis resistant to aliphatic, aromatic hydrocarbons. It is extremely resistant to compression set,even at high temperatures. It has exceptional good resistance to atmospheric oxidation,sun, weather, fungus and mold. It has good electrical properties in low voltage, low frequencyapplications and low burning characteristics.

Tetrafluoroethylene (TFE) and propylene (P) - TFE/P or AFLAS compounds have almostuniversal resistance to acids and bases, steam, acid gases, crude oil and many types ofcorrosion inhibitors. TFE's can withstand temperatures from -10°F to -450°F with briefexposure slightly higher. Aflas can be formulated for additional steam resistance.

Temperatures and ratings above have been gathered from our technical personnel or general informationfrom individual elastomer manufacturers. The statements and technical information are typicallydetermined by testing in a controlled environment and/or by field experience. Specific downhole conditionsmay or may not affect these temperature ratings as stated.

BASIC RUBBER PROPERTIES


The Tryton Open Hole Reamer is generally ran in order to dress out theopen hole before installing Tryton Multi-Stage Frac systems.

The Reamer is a rigid heavy duty one-piece tool with 2 sets of 12opposing tungsten carbide capped spiraled blades with an OD close tohole tolerances in order to best prepare the well bore ID properly beforerunning tools.

OPEN HOLE REAMER

HEAVY DUTY ONE PIECE DESIGN

2 SETS OF 12 TUNGSTEN CARBIDE BLADES

CLOSE OD TO OPEN HOLE TOLERANCE


* For more information please contact us by phone or email.

The Tryton Open Hole Centralizer is mainly used with TrytonOpen Hole Packers, generally as part of the Tryton Multi-StageFrac System. The Centralizer helps to protect the packers fromdamage during equipment installation in the open hole section ofthe well bore as well as helping to centralize the packers duringthe setting procedure. The Centralizer freely swivels to allow forrotation when running in the hole if required and has spiralledgrooves to ensure good circulation.

OPEN HOLE CENTRALIZER

AVAILABLE IN COMPOSITE OR STEEL

HELPS PREVENT RUNNING DAMAGE

CENTRALIZES WHEN SETTING

SWIVELS TO ALLOW FOR TOOL STRING ROTATION



DESIGNED FOR BOTH VERTICAL AND HORIZONTAL APPLICATIONS

INCORPORATES A BI-DIRECTIONAL SLIP SYSTEM

PREVENTS BOTH UPWARD AND DOWNWARD MOVEMENT

FULL BORE ID

INTERNAL LOCKING MECHANISM

FIELD ADJUSTABLE SHEAR RELEASE

SETS WITH DIFFERENTIAL PRESSURE ONLY

AVAILABLE WITH CARBIDE SLIPS

DESIGNED FOR HIGH TENSILE LOADS

The Tryton RSB-1 Liner Hanger/Packer is designed to be ran in applications where shortto long liner tailpipe assemblies are required. All load bearing parts are designed towithstand large tension loads which makes it ideal for both vertical and horizontalapplications whereby the liner system is to be anchored in place. The bi-directional slipsystem prevents both upward and downward movement after the tool is set. The RSB-1does not rely on setting string weight or tension as it is set completely with differentialhydraulic pressure.

The RSB-1 has both an upper seal bore in order to maximize the ID through the connectedtubing string.

The RSB-1 is hydraulically set using the RSB Hydraulic Setting Tool and has a fieldadjustable shear release.

RSB-1 LINER HANGER/PACKER



LARGE INTERNAL BYPASS

SECONDARY BALL SEAT

SELF DRAINING WHEN PULLING OUT OF HOLE

OPTIONAL SUPPLEMENTARY SETTING CHAMBERS

FIELD ADJUSTABLE SETTING PRESSURE

CAN BE CUSTOMIZED TO SET ANY SEAL BORE PACKER

TECHNICAL DATA

The Tryton RSB Hydraulic Setting Tool was designed to set the RSB-1 Liner Hanger Packereither by itself or in conjunction with other equipment such as Tryton's horizontal Multi-StageFrac system. In addition to the RSB-1 Liner Hanger Packer, the RSB Setting Tool can becustomized to set any Seal Bore Packer

When ran without a lower plugging device in the tailpipe a large internal by-pass allows fluidto enter the work string eliminating the need to fill the work string while running in the hole. Ifthere is tailpipe assembly such as the Multi-Stage Frac system with some type of float shoeor other type of plugging device in place then it may be necessary to fill while running in thehole.

Once on depth, field adjustable differential pressure is applied activating a hydraulicchamber stroking the RSB Setting Tool against the whichengages the slips and energizes the elements. There is a secondary ball seat within thesetting tool if required.

Once the is set and tested the RSB setting tool is released with acombination of right hand rotation while holding tension. Ports between seals ensuresdrainage while tripping.

RSB-1 Liner Hanger Packer

RSB-1 Liner Hanger Packer

RSB HYDRAULIC SETTING TOOL

SETTING CHAMBER AREA BASE TOOL O.D. MAX TOOL I.D. THREAD CONNECTION

Sq. In. Sq. cm in. mm in. mm in. mm

21.3 137.43 5.50 139.70 3.00 76.20 3 1/2 IF 88.9


PREVENTS BOTH UPWARD AND DOWNWARD MOVEMENT WHEN LATCHED

HEAVY DUTY BONDED SEALS

AVAILABLE WITH PREMIUM ELASTOMERS

LARGE BORE ID

AVAILABLE IN A WIDE RANGE OF MATERIALS AND CONNECTIONS

TECHNICAL DATA

RSB LATCH SEAL ASSEMBLY

CASING SIZE SEAL BORE SIZE MAX TOOL O.D. MIN TOOL I.D. THREAD CONNECTION

in. mm in. mm in. mm in. mm in. mm

7 177.8 4.00 101.60 5.00 127.00 3.00 76.20 3 1/2 EUE 88.9

7 177.8 4.75 120.65 5.88 149.35 3.88 98.55 4 1/2 LT&C 114.3

The Tryton RSB Latch Seal Assembly is designed to be used with either theRSB or the RSB-1 Packer. The RSB seal assembly incorporates heavy dutyquadruple bonded seals and is ran on the tubing after the packer has beenset. The latch mechanism engages automatically with set down weight anddisengages with right hand rotation while pulling tension.


The Tryton AnchorPac and the IsoPac packers are designed to be run in eithercased or open hole applications in vertical or horizontal wells. TheAnchorPac canbe ran as a single zone application packer or ran in conjunction with severalpackers in a multiple zone completion. The AnchorPac Packer incorporates aone piece bi-directional slip system in order to help prevent movement duringhigher pressure operations

. Typically, on multiple zone horizontal open hole applications theAnchorPac would be used as the toe packer and/or the liner hanger packer.Durable construction and reliability makes the IsoPac Packer and theexcellent alternatives to using inflatable packers.

The setting pressurecan be field adjusted with readily accessible setting shear screws. Both packershave a straight pull shear release which can also be readily adjusted in the field.

whereby the IsoPac Packer is a non-anchoringpacker

The AnchorPac and the IsoPac are hydraulically set with an internal lockingmechanism providing a positive and reliable long term set.

AnchorPac

SINGLE ACTION SETTING PISTON

OUTER COMPONENTS LOCKED TO PREVENT PREMATURE SETTING

ANCHORPAC INCORPORATES A BI-DIRECTIONAL SLIP SYSTEM




DESIGNED FOR OPEN HOLE




CASED HOLE OR

VERTICAL/HORIZONTAL APPLICATIONS

ANCHORPAC / ISOPAC PACKERS



SWELLRIGHT PACKER

The SwellRight Packer's standard swellable packer range is available as an oilor water swelling elastomer. This single element design uses a patent pendingbonding process to provide high performance over short element lengths.SwellRight packers are available in wide range of sizes and utilize proprietary oiland water swell compounds.

SIMPLE TO INSTALL

STRONG AND DURABLE

VERTICAL/HORIZONTAL APPLICATIONS


OIL AND WATER ACTIVATION AVAILABLE

BASE PIPE O.D. ELEMENT O.D. HOLE SIZE ELEMENT LENGTH

in. mm in. mm in. mm ft m

2.375 60.3 3.500 88.9 4.000 101.6 3, 6 & 10 0.9, 1.8 & 3.0

2.875 73.0 4.000 101.6 4.750 120.7 3, 6 & 10 0.9, 1.8 & 3.0

3.500 88.9 5.750 146.1 6.125 155.6 3, 6 & 10 0.9, 1.8 & 3.0

4.000 101.6 5.625 142.9 6.000 152.4 3, 6 & 10 0.9, 1.8 & 3.0

4.000 101.6 5.750 146.1 6.125 155.6 3, 6 & 10 0.9, 1.8 & 3.0

4.500 114.3 5.625 142.9 6.000 152.4 3, 6 & 10 0.9, 1.8 & 3.0

4.500 114.3 5.750 146.1 6.125 155.6 3, 6 & 10 0.9, 1.8 & 3.0

4.500 114.3 5.875 149.2 6.250 158.8 3, 6 & 10 0.9, 1.8 & 3.0

5.500 139.7 8.150 207.0 8.500 215.9 3, 6 & 10 0.9, 1.8 & 3.0

6.625 168.3 8.150 207.0 8.500 215.9 3, 6 & 10 0.9, 1.8 & 3.0

7.000 177.8 8.150 207.0 8.500 215.9 3, 6 & 10 0.9, 1.8 & 3.0

7.000 177.8 9.150 232.4 9.500 241.3 3, 6 & 10 0.9, 1.8 & 3.0

7.625 193.7 9.150 232.4 9.500 241.3 3, 6 & 10 0.9, 1.8 & 3.0

9.625 244.5 11.500 292.1 12.250 311.2 3, 6 & 10 0.9, 1.8 & 3.0

13.375 339.7 16.500 419.1 17.500 444.5 3, 6 & 10 0.9, 1.8 & 3.0

TECHNICAL DATA


FZR ON/OFF TOOL

PROVEN BONDED SEAL SYSTEM

RIGHT HAND RELEASE

3 LUG J-SLOT DESIGN FOR HIGH TENSILE LOADING

FULL BORE ID

WIRELINE PROFILE CAN BE CUT IF REQUIRED

AVAILABLE IN A WIDE RANGE OF MATERIALS & CONNECTIONS

The Tryton FZR On/Off is an overshot type tubing disconnect/connectincorporating a J-slot that automatically engages on and disengages witha ¼ turn to the right at the tool. The FZR On/Off incorporates a provenand reliable quadruple bonded valve system which can be made out ofvarious elastomeric materials as required. The FZR has a heavy duty 3lug J-slot design to maximize the tensile loading capability and a full boreslick joint that allows for the largest possible ID available whilemaintaining a high pressure rating. A wireline profile can be cut in theslick joint if required.



FB/CFB HYDROPORT FRAC SLEEVE

The Tryton FB/CFB HydroPortFrac Sleeves are designed for use when selectivelystimulating multiple zones in either open or cased hole applications. The HydroPortcan be used in either horizontal or vertical wells and is usually the first valve ran inthe well accompanied by multiple IsoPort Frac Sleeves. The HydroPort Frac Sleeveis hydraulically opened and an internal locking mechanism ensures the openposition is securely maintained.

The HydroPort Frac Sleeve is activated by field adjustable differential pressurefrom inside the sleeve across the actuation ports either by a plugging device below,usually being the ball seat circulating sub, or by isolating the sleeve with the FracDiverter Cup Tool.

Both the FB and CFB Frac Sleeves can be cemented in the hole and will reliablyfunction as they have an isolated internal shifting mechanism. Once open, thesleeves have an internal locking mechanism to ensure the open position is securelymaintained. The CFB has external fins across the frac ports to minimize thecement thickness between the sleeve and the formation.


FIELD ADJUSTABLE OPENING PRESSURE

SUITABLE FOR HIGH PRESSURE APPLICATIONS

DESIGNED FOR BOTH HORIZONTAL AND VERTICAL APPLICATIONS

DESIGNED FOR MULTIPLE ZONE APPLICATIONS

FULL BORE ID




The Tryton IsoPort Frac Sleeve is designed for selectively stimulatingmultiple zones in either open or cased hole applications. The IsoPort canbe used in either vertical or horizontal wells usually in conjunction with theHydroPort Frac Sleeve and IsoPac/AnchorPac Packers. The IsoPortFrac Sleeve is activated by circulating a ball into a drillable seat inside thetool. Applied differential pressure from above the ball seat shifts theinternal piston downward opening up the frac ports. The IsoPort has aninternal locking mechanism keeping the piston locked securely into placeafter it has been shifted. The standard IsoPort piston is made out of aeasily drillable material.



SUITABLE FOR HIGH PRESSURE APPLICATIONS

DESIGNED FOR HORIZONTAL AND VERTICAL APPLICATIONS


EASILY DRILLABLE BALL SEAT


CLOSABLE OPTION AVAILABLE

ISOPORT FRAC SLEEVE



GATEWAY ISO-PORT FRAC SLEEVE

The Tryton has all the proven features ofthe conventional Tryton Iso-Port with the additional benefit of selectivezone isolation. The Gateway is ran as part of the conventional Multi-Stage Frac systemand after the sleeve is opened utilizing ball droptechnology, the piston can then be drilled out and the sleeve can beclosed/opened using the activation tool on coil.

Gateway Iso-Port Frac Sleeve




CAN BE CLOSED/OPENED WITH COIL RAN ACTIVATION TOOL



MULTI - PORT FRAC SLEEVE

Tryton's Multi-Port Frac Sleeve is a ball drop activated frac valve speciallydesigned to generate more fracs in less time in a wellbore by using asingle ball to shift open multiple frac sleeves thereby allowing for pin pointstimulation. The Multi-Port valves are installed either as part of an openhole packer liner system or can be cemented in with the liner. Once thesystem has been designed and ran, one ball will shift open all valves inthe same stage prior to landing in a fixed ball seat at the bottom of thestage. Up to 20 sleeves can be opened with a single ball and the seatsare easily millable for future well intervention.

ONE BALL CAN OPEN UP TO 20 SLEEVES

CAN BE RAN WITH OPEN HOLE PACKERS OR CEMENTED IN

EASILY MILLABLE SEATS

FRAC PORTS CAN BE DESIGNED IN NUMBER AND SIZE TO

OPTIMIZE STIMULATION



The Tryton Ball Seat Circulating Sub is designed to be a reliablecloseable circulation port generally ran at the bottom of a tool stringin either cased or open hole for vertical or horizontal wellcompletions. Once the tool string is in place and the requiredcirculation operation is complete a ball is circulated onto the seat,an adjustable pre-determined pressure is applied and an internalsleeve shifts downwards which closes the internal circulatingports. Once the sleeve has been shifted a positive lockingmechanism ensures it is securely maintained in place.

Standard ball sizes are 0.75" (19.05mm) and 1.00" (25.40mm) butcan be customized if required.

INTERNAL SECURE LOCKING MECHANISM

ADJUSTABLE CLOSING PRESSURE

DESIGNED FOR BOTH HORIZONTAL AND VERTICAL APPLICATIONS

DESIGNED FOR BOTH CASED AND OPEN HOLE APPLICATIONS


BALL SEAT CIRCULATING SUB



The Tryton Viking Frac Sleeve is designed for selectively stimulatingmultiple zones in either vertical or horizontal wells. The Viking FracSleeve can either be ran in conjunction with Tryton open hole packersor be cemented in the well bore. As many sleeves as required can beran and each sleeve opens independently utilizing the Tryton VikingActuation Tool on coil tubing. Using the Viking system, the frac canbe pumped down the ID of the coil or the coil annulus.

The Tryton Viking Actuation Tool utilizes a continuous J-slot toactivate the locator keys for positive locating and anchoring into eachsleeve. Each sleeve is independently opened upon reaching apreset field adjustable differential pressure from inside the sleeve.After stimulation, the coil is picked up, opening the unloader valve,resetting the tool to the running position and moved up to the nextsleeve.

VIKING FRAC SLEEVE/ACTUATION TOOL


FIELD ADJUSTABLE OPENING PRESSURE

CAN BE USED IN CONJUNCTION WITH OPEN HOLE PACKERSOR CEMENTED IN PLACE


NO LIMIT ON THE NUMBER OF SLEEVES RAN

FULL BORE ID

ACTUATION TOOL UTILIZES SIMPLE DESIGN WITH HEAVY DUTYREINFORCED CUP FOR DURABILITY AND EFFICIENCY

CAN BE PUMPED DOWN THE COIL ID OR COIL ANNULUS



CAN BE USED WITH A WIDE RANGE OF FRAC PORT SYSTEMS

STIMULATION OF MULTI-

FUNCTIONS IN VERTICAL, DEVIATED, OR HORIZONTAL WELLS

RAPID DEPLOYMENT THROUGH FLUID FILLED WELLBORES

SINGLE CUP

LARGE

FIELD ADJUSTABLE COIL TUBING SHEAR RELEASE

ZONE WELLBORES - NEW & RECOMPLETIONS

ASSEMBLY AVAILABLE

BORE

The TLT Frac Tool is designed for stimulating isolated zones within casedvertical or horizontal well bores utilizing coil tubing. Quicker running speedscan be achieved even when moving through fluid or live wells due to aninnovative fluid bypass. When moving up-hole the valve shuts providing aclosed system isolating the target zone and containing fluids/proppants from allpreviously stimulated lower zones. The top end of the TLT tool incorporates acoil tubing field adjustable shear release.

The TLT can be used in conjunction with the Tryton FB/CFB HydroPorts or anyother similar frac port systems such as other types of frac sleeves, burstdisks or perforations.

type

TLT FRAC TOOL

CASING SIZE CASING WEIGHT THIMBLE O.D. MIN I.D. THREAD CONNECTION

in. mm lbs/ft kg/m in. mm in. mm in. mm

4 1/2 114.3 9.5-13.5 14.1-20.1 3.860 98.0 1.81 46.0 2 3/8 EUE 60.3

5 1/2 139.7 15.5-17.0 23.1-25.3 4.750 119.4 1.81 46.0 2 3/8 EUE 60.3

5 1/2 139.7 13.0-15.5 19.3-23.1 4.810 122.2 1.81 46.0 2 3/8 EUE 60.3

TECHNICAL DATA


BDR COIL FRAC STIMULATION TOOL

The Tryton BDR Coil Frac Stimulation Tool allows operators to stimulate coalbed methane formations via extreme overbalance.

The assembly is run to depth on coil tubing, isolating selected perf intervals tobe stimulated (shocked) with Nitrogen. Composite drop balls are deployedfrom surface and seal in a seat in the BDR. At a preset pressure of 30 mpa theball is forced through the seal and nitrogen is released into the formation. TheBDR can then be moved to straddle the next interval and the process isrepeated. The design optimizes the amount of

The surge of Nitrogenextends through the existing well bore damage without harming theformation.

Nitrogen required and allowsaccess to maximum perforations in a single trip.

SIMPLE DESIGN - NO MOVING PARTS

DURABLE AND EFFICIENT

ONE TRIP - MULTIPLE INTERVALS

SIMPLE FIELD REDRESS

CASING SIZE MAX METAL O.D. BALL SIZE SEAT SIZE TOOL LENGTH

in. mm in. mm in. mm in mm in cm

4 1/2 114.3 3.682 93.5 1.5 38.10 1.0 25.4 72.6 184.4

TECHNICAL DATA


TGW CUP PACKER

The Tryton TGW Cup Packer is available in a single or double cup design.The primary use is for isolating casing and tubing leaks. The packer cupscan be installed in any direction allowing each assembly to hold pressurein both directions if required.

AVAILABLE IN SINGLE OR DOUBLE ELEMENT DESIGN

COMPACT & INEXPENSIVE MEANS OF ISOLATION

WIRE REINFORCED CUPS FOR DURABILITY

TECHNICAL DATA

CASING SIZE THREAD CONNECTIONS CASING WEIGHT MAX O.D. MIN I.D.

in. mm in. mm lbs/ft. kg/m in. mm in. mm

4 1/2 114.3 2 3/8 EUE 60.3 15.1-16.6 22.5-24.7 4.08 103.6 2.00 50.8

4 1/2 114.3 2 3/8 EUE 60.3 9.5-11.6 14.1-17.2 4.15 105.4 2.00 50.8

5 127.0 2 3/8 EUE 60.3 18.0-21.0 26.8-30.2 4.34 110.3 2.00 50.8

5 127.0 2 3/8 EUE 60.3 13.0-15.0 19.3-22.3 4.62 117.3 2.00 50.8

5 1/2 139.7 2 3/8 EUE 60.3 17.0-23.0 29.8-34.2 4.98 126.4 2.50 63.5

5 1/2 139.7 2 3/8 EUE 60.3 15.5-17.0 23.1-25.3 5.12 130.0 2.50 63.5

5 1/2 139.7 2 3/8 EUE 60.3 13.0-15.0 19.3-22.3 5.20 132.0 2.50 63.5

7 177.8 2 7/8 EUE 73.0 26.0-29.0 38.7-43.1 6.38 162.0 2.50 63.5

7 177.8 2 7/8 EUE 73.0 22.0-24.0 32.7-35.7 6.59 167.3 2.50 63.5

7 177.8 2 7/8 EUE 73.0 17.0-20.0 25.3-29.8 6.62 168.1 2.50 63.5

Common sizes above, other sizes may be available if required


TD-1 TENSION PACKER

The Tryton TD-1 Tension Packer is a compact, economical, retrievablepacker. Primarily used in water flood applications, this packer can alsobe used for production and/or lower-medium pressure treatingoperations. It is used where a set-down packer is impractical. Since theTD-1 is tension set, it is ideally suited for shallow wells where set-downweight is not available.

UTILIZES RUGGED ROCKER TYPE SLIP

LARGE BORE

SIMPLE LOW COST PACKER FOR FLUID INJECTION

ALTERNATIVE SHEAR RELEASE

CASING PACKER

O.D. WEIGHT MIN. I.D. MAX I.D. MAX O.D. THREAD CONNECTION

in. mm lbs/ft kg/m in. mm in. mm in. mm in. (mm)

4 1/2 114.3 9.5-13.5 14.17-20.13 3.920 99.57 4.090 103.89 3.771 95.78 2 3/8 ( 60.3 mm) EUE

5 127.0 15.0-18.0 22.37-26.84 4.276 108.61 4.408 111.96 4.125 104.78 2 3/8 ( 60.3 mm) EUE

5 127.0 11.5-15.0 17.15-22.37 4.408 111.96 4.560 115.82 4.250 107.95 2 3/8 ( 60.3 mm) EUE

5 1/2 139.7 20.0-23.0 29.83-34.30 4.670 118.62 4.788 121.62 4.500 114.30 2 3/8 ( 60.3 mm) EUE

5 1/2 139.7 15.5-20.0 23.11-29.83 4.778 121.36 4.950 125.73 4.641 117.88 2 3/8 ( 60.3 mm) EUE

5 1/2 139.7 13.0-17.0 19.39-25.35 4.892 124.26 5.044 128.12 4.750 120.65 2 3/8 ( 60.3 mm) EUE

5 1/2 139.7 13.0-15.5 19.39-23.11 4.950 125.73 5.044 128.12 4.781 121.44 2 3/8 ( 60.3 mm) EUE

7 177.8 38.0 56.67 5.830 148.08 5.921 150.39 5.656 143.66 2 7/8 ( 73.0 mm) EUE

7 177.8 32.0-35.0 47.72-52.20 6.044 153.52 6.094 154.79 5.812 147.62 2 7/8 ( 73.0 mm) EUE

7 177.8 26.0-29.0 38.78-43.25 6.184 157.07 6.276 159.41 5.968 151.59 2 7/8 ( 73.0 mm) EUE

7 177.8 20.0-26.0 29.83-38.78 6.276 159.41 6.456 163.98 6.078 154.38 2 7/8 ( 73.0 mm) EUE

7 177.8 17.0-20.0 25.35-29.83 6.456 163.98 6.538 166.07 6.266 159.16 2 7/8 ( 73.0 mm) EUE

TECHNICAL DATA



TS-3 SINGLE GRIP COMPRESSION PACKER

The TS-3 Single Grip Packer is a single-grip, compression-set,retrievable mechanical production packer that is suitable for mostproduction, stimulation and testing operations. The field proven largebore design allows unrestricted fluid flow and wireline operations throughthe tubing. The TS-3 also incorporates an internal bypass to preventswabbing when running and retrieving.

OPTIONAL J-SLOT CONFIGURATIONS

LARGE BYPASS FOR RUNNING, RETRIEVING AND EQUALIZING

NORMALLY RH COMPRESSION SET, STRAIGHT PICK-UP RELEASE

AVAILABLE WITH BOTH LONG AND SHORT STROKE MANDRELS

CASING SIZE CASING WEIGHT O.D. OF TOOL THREAD CONNECTIONS

in. mm lbs/ft kg/m in. mm in. mm

4 1/2 114.3 15.1-16.6 22.3-24.6 3.594 91.29 2 3/8 EUE 60.3

4 1/2 114.3 9.5-13.5 14.1-20.1 3.750 95.25 2 3/8 EUE 60.3

5 127.0 18.0-20.8 26.82-13.9 4.000 101.60 2 3/8 EUE 60.3

5 127.0 11.5-15.0 17.1-22.3 4.125 104.78 2 3/8 EUE 60.3

5 1/2 139.7 20.0-23.0 29.8-34.2 4.500 114.30 2 3/8 EUE 60.3

5 1/2 139.7 13.0-20.0 19.4-29.8 4.625 117.48 2 3/8 EUE 60.3

5 1/2 139.7 20.0-23.0 29.8-34.2 4.500 114.30 2 7/8 EUE 73.0

5 1/2 139.7 15.5-20.0 23.1-29.8 4.625 117.48 2 7/8 EUE 73.0

5 1/2 139.7 13.0-14.0 19.2-20.8 4.813 122.25 2 7/8 EUE 73.0

7 177.8 17.0-26.0 25.3-38.7 6.125 139.70 2 7/8 EUE 73.0

7 177.8 26.0-35.0 38.7-51.8 5.875 149.23 2 7/8 EUE 73.0

TECHNICAL DATA


TS-4 DOUBLE GRIP COMPRESSION PACKER

The Tryton TS-4 Compression Set Packer is used forproduction, stimulation and testing. The mechanical upper hold downsystem reduces the cost and maintenance of a button type hydraulic holddown system. The TS-4 is equipped with a running bypass that reducesswabbing. Set down weight closes the bypass valve, sets the upper/lowerslips and energizes the packing elements. The closed bypass valveactivates the pressure balanced hold down system. Internal pressure frombelow the elements aids in holding the bypass valve closed and preventingupward movement of the tubing string.

Double Grip

To set, run the tool to setting depth, pick up tubing and rotate to the right ¼turn at the packer. Tubing weight is applied, which sets the lower slips,closes the bypass valve and expands the packing elements.

To release, raise the tubing, which first opens the bypass valve, thenreleases the slips and packing elements.

NO HYDRAULIC HOLD DOWN BUTTONS

BUILT IN UNLOADER WASHES DEBRIS FROM WHEN RETRIEVING

SEQUENTIAL RELEASE UPPER SLIP SYSTEM

AVAILABLE IN AUTOMATIC AND MANUAL JAY CONFIGURATIONS

NORMALLY RIGHT HAND COMPRESSION SET, STRAIGHT PICK-UP RELEASE

CASING SIZE CASING WEIGHT THREAD CONNECTION MAX O.D. MIN I.D.


2 7/8 73.0 6.4-6.5 9.5-9.7 1.050 EUE 26.7 2.250 57.15 0.625 15.88

3 1/2 88.9 7.7-10.2 11.5-15.0 1.900 NUE 48.3 2.781 70.63 1.250 37.75

4 1/2 114.3 9.5-13.5 14.1-20.9 2 3/8 EUE 60.3 3.750 95.25 2.000 50.80

5 127.0 18.0-20.8 26.8-31.0 2 3/8 EUE 60.3 4.000 101.60 2.000 50.80

5 127.0 11.5-15.0 17.1-22.3 2 3/8 EUE 60.3 4.125 104.78 2.000 50.80

5 1/2 139.7 20.0-23.0 29.8-34.2 2 3/8 EUE 60.3 4.500 114.30 2.000 50.80

5 1/2 139.7 14.0-20.0 20.8-29.8 2 3/8 EUE 60.3 4.625 117.48 2.000 50.80

5 1/2 139.7 20.0-23.0 29.8-34.2 2 7/8 EUE 73.0 4.500 114.30 2.375 60.30

5 1/2 139.7 15.5-20.0 23.1-29.8 2 7/8 EUE 73.0 4.625 117.48 2.375 60.30

7 177.8 26.0-32.0 38.7-47.6 2 7/8 EUE 73.0 5.875 149.23 2.500 63.50

7 177.8 17.0-26.0 25.3-38.7 2 7/8 EUE 73.0 6.000 152.40 2.500 63.50

TECHNICAL DATA



SNAPSET COMPRESSION SET ISOLATION PACKERS

The Tryton Snapset Compression Set Isolation Packers are used in multi-zonecompletions. The Snapset Packers set in compression with a lower anchor stylepacker below. The collet in the lower end of the tool shifts at a pre-determined value toenergize the packing elements and set the upper slips. To release, straight pick-up onthe tubing string is required.

The Snapset I has no slips, the Snapset II has a tension slip only and the Snapset IIIhas a compression slip only. The application and operational requirements willdetermine which is the best Snapset to use.

COMPENSATING PISTON HOLD DOWN SYSTEM

RUNNING BYPASS/

KEYED FOR ROTATION THRU PACKER

INTERNAL COLLET TO PREVENT PRE-SET

SEQUENTIAL RELEASE SLIP SYSTEM

EQUALIZING SYSTEM

CASING SIZE CASING WEIGHT THREAD CONNECTION MAX. O.D. MIN I.D.


2 7/8 73.0 6.4-6.5 9.5-9.7 1.050 EUE 26.7 2.250 57.15 0.625 15.88

4 101.6 9.5-11.0 14.1-16.4 1.900 EUE 48.3 3.250 82.55 1.500 38.10

4 1/2 114.3 15.1-16.6 22.5-24.7 1.900 EUE 48.3 3.594 91.29 1.500 38.10

4 1/2 114.3 13.5-15.1 20.1-22.5 2 3/8 EUE 60.3 3.656 92.86 1.938 49.23

4 1/2 114.3 9.5-13.5 14.1-20.1 2 3/8 EUE 60.3 3.750 95.25 1.938 49.23

5 127.0 11.5-15.0 17.1-22.3 2 3/8 EUE 60.3 4.125 104.78 1.938 49.23

5 127.0 18.0-20.8 26.8-31.0 2 3/8 EUE 60.3 4.000 101.60 1.938 49.23

5 1/2 139.7 13.0-14.0 19.3-20.8 2 3/8 EUE 60.3 4.812 122.22 2.000 50.80

5 1/2 139.7 14.0-20.0 20.8-29.8 2 3/8 EUE 60.3 4.625 117.48 2.000 50.80

5 1/2 139.7 20.0-23.0 29.8-34.2 2 3/8 EUE 60.3 4.500 114.30 2.000 50.80

5 1/2 139.7 13.0-14.0 19.3-20.8 2 7/8 EUE 73.0 4.812 122.22 2.375 60.30

5 1/2 139.7 13.0-15.5 19.3-23.1 2 7/8 EUE 73.0 4.781 121.44 2.375 60.30

5 1/2 139.7 15.5-20.0 23.1-29.8 2 7/8 EUE 73.0 4.625 117.48 2.375 60.30

5 1/2 139.7 20.0-23.0 29.8-34.2 2 7/8 EUE 73.0 4.500 114.30 2.375 60.30

6 152.4 14.0-20.0 20.8-29.8 2 7/8 EUE 73.0 5.188 131.78 2.375 60.30

6 5/8 139.7 24.0-32.0 35.8-47.6 2 7/8 EUE 73.0 5.500 139.70 2.500 63.50

6 5/8 168.3 17.0-20.0 25.3-29.8 2 7/8 EUE 73.0 5.750 146.10 2.500 63.50

7 177.8 17.0-26.0 25.3-38.7 2 7/8 EUE 73.0 6.000 152.40 2.500 63.50

7 177.8 23.0-29.0 34.2-43.2 2 7/8 EUE 73.0 5.969 151.61 2.500 63.50

7 177.8 26.0-32.0 38.7-47.6 2 7/8 EUE 73.0 5.875 149.23 2.500 63.50

7 5/8 193.7 24.0-29.7 35.7-44.2 2 7/8 EUE 73.0 6.672 169.47 2.500 63.50

7 5/8 193.7 33.7-39.0 50.2-58.0 2 7/8 EUE 73.0 6.453 163.91 2.500 63.50

8 5/8 219.1 24.0-40.0 35.7-59.5 2 7/8 EUE 73.0 7.500 190.50 2.500 63.50

TECHNICAL DATA



The Tryton THI Hydraulic Isolation Packer is a hydraulic set,single string tandem packer used in multiple zone wells. TheTHI Hydraulic Isolation Packer is generally used as thelower/middle packer(s) in multiple zone applications.

THI HYDRAULIC ISOLATION PACKER

ECONOMICAL

EASILY ADJUSTABLE SET AND RELEASE SHEAR SCREWS

COMPACT DESIGN

CAN BE USED IN OPEN HOLE

TECHNICAL DATA

CASING SIZE CASING WEIGHT TUBING SIZE MAX O.D. MIN I.D.


4 1/2 114.3 9.5-13.5 14.1-20.9 2 3/8 EUE 60.3 3.750 95.25 2.000 50.80

5 127.0 18.0-20.0 26.8-31.0 2 3/8 EUE 60.3 4.000 101.60 2.000 50.80

5 127.0 11.5-15.0 17.1-22.3 2 3/8 EUE 60.3 4.125 104.78 2.000 50.80

5 1/2 139.7 20.0-23.0 29.8-34.2 2 3/8 EUE 60.3 4.500 114.30 2.000 50.80

5 1/2 139.7 13.0-20.0 19.3-29.8 2 3/8 EUE 60.3 4.625 117.48 2.000 50.80

5 1/2 139.7 20.0-23.0 29.8-34.2 2 7/8 EUE 73.0 4.500 114.30 2.500 63.50

5 1/2 139.7 13.0-20.0 19.3-29.8 2 7/8 EUE 73.0 4.625 117.48 2.500 63.50

7 177.8 26.0-32.0 38.7-47.6 2 7/8 EUE 73.0 5.875 149.23 2.500 63.50

7 177.8 17.0-26.0 25.3-38.7 2 7/8 EUE 73.0 6.000 152.40 2.500 63.50


HYDRO-CT PACKER

The Tryton Hydro-CT Packer can be ran either on jointed pipe utilizing aconventional rig or rigless application using coil tubing. The Hydro-CT can beran alone or in tandem for testing, production, water shut-off or zonal isolation ineither vertical or horizontal wells. The Hydro-CT is hydraulically set with aninternal locking mechanism providing a positive and reliable long-term pack-off.Both durable construction and compact size makes the Hydro-CT Packer anexcellent alternative to conventional hydraulic packers in shallower wells.

The Hydro-CT is released by dropping a ball onto an internal seat then pressureabove causes the releasing pins to shear and the packer to release.

TECHNICAL DATA




RELEASING MECHANISM INDEPENDENT OF SETTING MECHANISM

CAN BE RAN IN SINGLE OR MULTIPLE PACKER APPLICATIONS

CAN BE USED IN CONJUNCTION WITH OTHER COMPLETION TOOLS

SUITED FOR BOTH VERTICAL AND HORIZONTAL APPLICATIONS



4 1/2 114.3 9.5-13.5 14.1-20.9 2 3/8 EUE 60.3 3.750 95.25 2.000 50.80



The Tryton TI-1 Inflatable Single Set Packer is normally used forisolating zones or in casing whereby a restriction needs to be passed throughand can be used for testing, treating, production or injection. The TI-1 is ahydraulically set single use packer that may be used in both vertical orhorizontal wells.

After the TI-1 is set an internal locking sleeve maintains inflation. The packercomes in both rotational or straight pull release.

The TI-1 packer element incorporates high strength cable to provide goodexpansion characteristics in washed out or irregular well bores, as well as toprovide high differential pressure capabilities. After the packer is released, theelements are designed to return very close to the original run-in diameter. Theelements are less likely to lose rubber down hole because superior bondingoccurs between the rubber and cable rather than just rubber alone.

in open hole

TI-1 SINGLE SET PACKERINFLATABLE

TECHNICAL DATA

ELEMENT O.D. MIN. TOOL I.D. THREAD CONNECTIONS

in. mm in. mm in. mm

3.12 79.25 0.750 20.07 2 3/8 EUE 60.3

3.62 91.95 1.750 44.45 2 3/8 EUE 60.3

4.25 107.95 1.938 49.23 2 7/8 EUE 73.0

5.50 139.70 2.500 63.50 2 3/8 - 2 7/8 EUE 60.3-73.0

AVAILABLE IN TENSION OR ROTATIONAL RELEASE MODELS

INTERNAL SLEEVE MAINTAINS INFLATION IN PACKER

PRESSURE ACROSS ELEMENT IS FULLY EQUALIZED WHEN UNSETTING

HEAVY DUTY CABLE RE-INFORCED ELEMENT

DIFFERENT ELASTOMER COMPOUNDS AVAILABLE FOR HPHT

AVAILABLE IN A VARIETY OF MATERIALS AND CONNECTIONS



The TI-2 Inflatable Multi-Set Packer is used for isolating zones in open-hole or incasing. The tool is re-settable and may be used for testing, treating, production, orstimulation of several zones with each trip into the well. The TI-2 incorporates adurable rugged design for reliable multiple sets in the same trip.

The TI-2 Packer may be used in vertical, deviated or horizontal wells. No rotation isrequired to set the packer, however right-hand rotation is required to unset the packer.

Once the TI-2 is released it can be moved and re-set by dropping a dart into a seatwhereby the element can be re-inflated. The dart is then be pumped through to acatcher and the procedure can be repeated.

TI-2 INFLATABLE MULTI-SET PACKER

TECHNICAL DATA

ELEMENT O.D. MIN. TOOL I.D. THREAD CONNECTIONS


3.12 79.25 0.75 19.05 2 3/8 EUE 60.3

3.62 91.95 1.75 44.45 2 3/8 EUE 60.3

4.25 107.95 2.00 50.80 2 3/8 EUE 60.3

5.50 139.70 2.50 63.50 2 3/8 EUE - 2 7/8 EUE 60.3-73.0

CABLE REINFORCED ELEMENTS

EXPOSED CABLE ELEMENT AVAILABLE FOR CASED HOLES

RIGHT-HAND TURN RELEASE

USES SEATS AND DARTS TO RE-SET

DIFFERENT ELASTOMER COMPOUNDS AVAILABLE FOR HPHT

AVAILABLE IN A VARIETY OF MATERIALS AND CONNECTIONS



The Tryton Hydro-Grip II and Hydro-Grip III hydraulic set packers are single stringpressure activated double grip production packers used in single or multi zonecompletions. The Packers are ideally suited for applications where itis desired to set the packer(s) after the well is flanged up or for multiple zonecompletions. The Packers incorporates a pressure balance systemwhich helps compensate for pressure differentials across the packer.

In addition to having a 2 element cup type system instead of the 3 elementconventional system as is on the Hydro-Grip III, the Hydro-Grip II is a morecompact packer.

Hydro-Grip

Hydro-Grip

HYDRO-GRIP HYDRAULIC SET PACKERS

CUP TYPE TWO ELEMENT SYSTEM OR CONVENTIONALTHREE ELEMENT SYSTEM

RUNNING BYPASS

RELEASE EQUALIZING SYSTEM

PRESSURE BALANCED SYSTEM

STRAIGHT PULL RELEASE


FIELD ADJUSTABLE RELEASING SHEAR

TECHNICAL DATA

* Available in Hydro-Grip III OnlyCommon sizes above, other sizes may be available if required

*******




4 1/2 114.3 9.5-13.5 14.1-20.1 2 3/8 EUE 60.3 3.750 95.25 1.938 49.23

5 127.0 18.0-20.8 26.8-31.0 2 3/8 EUE 60.3 4.000 101.60 1.938 49.23

5 127.0 11.5-18.0 17.1-26.8 2 3/8 EUE 60.3 4.125 104.78 1.938 49.23

5 1/2 139.7 20.0-23.0 29.8-34.2 2 3/8 EUE 60.3 4.500 114.30 2.000 50.80

5 1/2 139.7 14.0-20.0 20.8-29.8 2 3/8 EUE 60.3 4.625 117.48 2.000 50.80

5 1/2 139.7 13.0-14.0 19.3-20.8 2 3/8 EUE 60.3 4.812 122.22 2.000 50.80

6 5/8 139.7 24.0-32.0 35.8-47.6 2 7/8 EUE 73.0 5.500 139.70 2.500 63.50

6 5/8 168.3 17.0-20.0 25.3-29.8 2 7/8 EUE 73.0 5.750 146.10 2.500 63.50

7 177.8 26.0-35.0 38.7-52.1 2 7/8 EUE 73.0 5.875 149.23 2.500 63.50

7 177.8 17.0-26.0 25.3-38.7 2 7/8 EUE 73.0 6.000 152.40 2.500 63.50

7 177.8 26.0-32.0 38.7-47.6 3 1/2 EUE 88.9 5.875 149.23 3.000 76.20

7 177.8 17.0-26.0 25.3-38.7 3 1/2 EUE 88.9 6.000 152.40 3.000 76.20

7 5/8 193.7 24.0-29.7 35.7-44.2 3 1/2 EUE 88.9 6.672 169.47 3.000 76.20

7 5/8 193.7 33.0-39.0 49.1-58.0 3 1/2 EUE 88.9 6.453 163.91 3.000 76.20

8 5/8 219.0 24.0-40.0 35.7-59.5 3 1/2 EUE 88.9 7.500 190.50 3.000 76.20

9 5/8 244.5 32.3-43.5 48.2-64.9 4 1/2 EUE 114.3 8.500 215.90 4.000 101.60

9 5/8 244.5 43.5-53.5 64.9-79.8 4 1/2 EUE 114.3 8.250 209.55 4.000 101.60

TD2 DUAL STRING PRODUCTION PACKER

The TD2 Dual String Packer is a hydraulic set, mechanically held dual stringproduction packer run above a single string hydraulic set or wireline set sealbore packer. Its short length makes it ideal for deviated wells or doglegs.Because no tubing manipulation is required to set this packer, the well head canbe installed and flanged up before setting. It is available with short string or longstring setting capabilities and a variety of tubing connections. It is also adaptablefor submersible pump applications. The TD2 features a sequential upper sliprelease system designed to release each slip individually reducing the pullrequired to release the packer. Due to the angles on the upper slips and upperslip cage, slips release smoothly from the casing.

CASINGTOOL O.D.

LONG STRING CONNECTIONS SHORT STRING CONNECTIONS

SIZE WEIGHT BOX UP/PIN DOWN MANDREL I.D. BOX UP/PIN DOWN MANDREL I.D.

in. mm lbs/ft kg/m in. mm in. mm in. mm in. mm in. mm

5 1/2 139.7 14.0-20.0 20.88-29.83 4.63 117.6 1.900 EUE 48.26 1.61 40.89 1.660 EUE 42.16 1.38 35.05

7 177.8 17.0-26.0 25.35-38.78 6.03 153.1 2 3/8 EUE 60.33 1.94 49.28 2 3/8 EUE 60.33 1.94 49.28

7 177.8 17.0-26.0 25.35-38.78 6.03 153.1 2 7/8 EUE 73.03 2.44 61.98 1.900 EUE 48.26 1.61 40.89

7 177.8 26.0-32.0 38.78-47.72 5.94 150.8 2 3/8 EUE 60.33 1.94 49.28 2 3/8 EUE 60.33 1.94 49.28

7 177.8 26.0-32.0 38.78-47.72 5.94 150.8 2 7/8 EUE 73.03 2.44 61.98 1.900 EUE 48.26 1.61 40.89

7 177.8 29.0-35-0 43.25-52.20 5.88 149.2 2 3/8 EUE 60.33 1.94 49.28 2 3/8 EUE 60.33 1.94 49.28

8 5/8 219.1 24.0-32.0 35.80-47.72 7.69 195.3 2 7/8 EUE 73.03 2.44 61.98 2 7/8 EUE 73.03 2.44 61.98

8 5/8 219.1 24.0-32.0 35.80-47.72 7.69 195.3 3 1/2 EUE 88.90 2.99 75.95 2 3/8 EUE 60.33 1.94 49.28

8 5/8 219.1 36.0-40.0 53.69-59.65 7.44 189.0 2 7/8 EUE 73.03 2.44 61.98 2 3/8 EUE 60.33 1.94 49.28

9 5/8 244.5 32.3-40.0 48.17-59.65 8.62 218.8 3 1/2 EUE 88.90 2.99 75.95 1.900 EUE 48.26 1.61 40.89

9 5/8 244.5 32.3-40.0 48.17-59.65 8.62 218.8 3 1/2 EUE 88.90 2.99 75.95 2 3/8 EUE 60.33 1.94 49.28

9 5/8 244.5 32.3-40.0 48.17-59.65 8.62 218.8 3 1/2 EUE 88.90 2.99 75.95 2 7/8 EUE 73.03 2.44 61.98

9 5/8 244.5 32.3-40.0 48.17-59.65 8.62 218.8 3 1/2 EUE 88.90 2.99 75.95 3 1/2 EUE 88.90 2.99 75.95

9 5/8 244.5 32.3-40.0 48.17-59.65 8.62 218.8 4 1/2 EUE 114.30 3.96 100.59 1.900 EUE 48.26 1.61 40.89

9 5/8 244.5 36.0-43.5 53.69-64.88 8.50 215.9 3 1/2 EUE 88.90 2.99 75.95 2 3/8 EUE 60.33 1.94 49.28

9 5/8 244.5 36.0-43.5 53.69-64.88 8.50 215.9 3 1/2 EUE 88.90 2.99 75.95 2 7/8 EUE 73.03 2.44 61.98

9 5/8 244.5 36.0-43.5 53.69-64.88 8.50 215.9 3 1/2 EUE 88.90 2.99 75.95 3 1/2 EUE 88.90 2.99 75.95

9 5/8 244.5 36.0-43.5 53.69-64.88 8.50 215.9 4 1/2 EUE 114.30 3.96 100.59 1.900 EUE 48.26 1.61 40.89

9 5/8 244.5 47.0-53.5 70.09-79.79 8.31 211.1 3 1/2 EUE 88.90 2.99 75.95 1.900 EUE 48.26 1.61 40.89

9 5/8 244.5 47.0-53.5 70.09-79.79 8.31 211.1 3 1/2 EUE 88.90 2.99 75.95 2 3/8 EUE 60.33 1.94 49.28

9 5/8 244.5 47.0-53.5 70.09-79.79 8.31 211.1 3 1/2 EUE 88.90 2.99 75.95 2 7/8 EUE 73.03 2.44 61.98

9 5/8 244.5 47.0-53.5 70.09-79.79 8.31 211.1 3 1/2 EUE 88.90 2.99 75.95 3 1/2 EUE 88.90 2.99 75.95

TECHNICAL DATA


TX-6/TX-6W DOUBLE GRIP PACKERRETRIEVABLE

The Tryton TX-6/TX-6W are lower pressure single string double grip retrievable

production packers that hold pressure from above and below. Once set, the TX-6/TX-

6W can be left in tension, compression or neutral. Incorporated into the design is an

internal bypass system that along with fluid by pass while running, equalizes pressure

before the upper slips are pulled from the casing wall. The TX-6/TX-6W Packers are

designed for production, testing, zone isolation and injection applications.

The TX-6 sets with a 1/4 right hand turn at the packer and releases with a 1/4 right hand

turn, then straight pick up. The TX-6W sets on wireline and releases with a 1/4 right

hand turn at the packer then straight pick-up. The TX-6 can be re-set multiple times

whereby once the TX-6W is released it cannot be re-set in the standard configuration.

CAN BE PACKED -OFF WITH EITHER TENSION OR COMPRESSION

QUARTER TURN TO RIGHT TO SET AND RELEASE

COMPATIBLE WITH A WIDE VARIETY OF TRYTON PACKER ACCESSORIES

TUBING, WIRELINE OR HYDRAULIC SET ON TUBING

OPTIONAL LH J-SLOT AVAILABLE



4 1/2 114.3 9.5-13.5 14.1-20.1 2 3/8 EUE 60.3 3.750 95.25 1.938 50.80

5 127.0 11.5-15.0 17.1-22.3 2 3/8 EUE 60.3 4.125 104.78 1.938 50.80

5 127.0 18.0-20.8 26.8-31.0 2 3/8 EUE 60.3 4.000 101.60 1.938 50.80

5 1/2 139.7 13.0-15.5 19.3-23.1 2 3/8 EUE 60.3 4.781 121.44 1.938 50.80

5 1/2 139.7 13.0-20.0 19.3-29.8 2 3/8 EUE 60.3 4.625 117.44 1.938 50.80

5 1/2 139.7 20.0-23.0 29.8-34.2 2 3/8 EUE 60.3 4.500 114.30 1.938 50.80

5 1/2 139.7 13.0-15.5 26.8-31.0 2 7/8 EUE 73.0 4.781 121.44 2.500 63.50

5 1/2 139.7 20.0-23.0 29.8-34.2 2 7/8 EUE 73.0 4.500 114.30 2.500 63.50

7 177.8 17.0-26.0 25.3-38.7 2 7/8 EUE 73.0 6.000 152.40 2.500 63.50

7 177.8 26.0-32.0 38.7-47.6 2 7/8 EUE 73.0 5.875 149.23 2.500 63.50

7 177.8 17.0-26.0 25.3-38.7 3 1/2 EUE 88.9 6.250 158.75 3.000 76.20

7 177.8 17.0-26.0 25.3-38.7 3 1/2 EUE 88.9 6.000 152.40 3.000 76.20

7 177.8 26.0-32.0 38.7-47.6 3 1/2 EUE 88.9 5.875 149.23 3.000 76.20

8 5/8 219.1 24.0-40.0 35.7-59.5 2 7/8 EUE 73.0 7.500 190.50 2.500 63.50

8 5/8 219.1 24.0-40.0 35.7-59.5 3 1/2 EUE 88.9 7.500 190.50 3.000 76.20

9 5/8 244.5 32.3-43.5 48.1-64.7 3 1/2 EUE 88.9 8.500 215.90 3.000 76.20

9 5/8 244.5 40.0-53.5 59.5-79.6 3 1/2 EUE 88.9 8.250 209.55 3.000 76.20

11 3/4 298.5 42.0-65.0 62.6-96.9 4 1/2 EUE 114.3 10.438 265.13 4.000 101.60

TECHNICAL DATA



The Tryton TX-8/TX-8W packers are medium pressure single string double

grip retrievable production packers that are capable of being set in tension

or compression. Once set, the tubing string can be left in tension,

compression or neutral. Incorporated into the design is an internal bypass

system that along with fluid bypass while running, equalizes pressure

before the upper slips are pulled from the casing wall. The Packers are

designed for stimulation, service operations, production, testing, zone

isolation and injection applications.

The TX-8 sets and releases with a 1/4 right hand turn at the packer, then

straight pick up. The TX-8W sets on wireline and releases with a 1/4 right

hand turn at the packer then straight pick-up. The TX-8 can be re-set

multiple times whereby once the TX-8W is released it cannot be re-set in the

standard configuration.


CAN BE PACKED-OFF WITH EITHER TENSION OR COMPRESSION

OPEN J-SLOT DESIGN

1/4 RIGHT HAND TURN TO SET AND RELEASE




COMPATIBLE WITH A WIDE VARIETY OF PACKER ACCESSORIES

SOUR SERVICE VERSION AVAILABLE



TX-8/TX-8W DOUBLE GRIP RETRIEVABLE PACKERTECHNICAL DATA



4 101.60 9.5-11.0 14.1-16.4 1.900 EUE 48.3 3.250 82.55 1.500 38.10

4 1/2 114.30 9.5-13.5 14.1-20.9 2 3/8 EUE 60.3 3.750 95.25 1.938 49.23

4 1/2 114.30 9.5-15.1 14.1-22.5 2 3/8 EUE 60.3 3.656 92.86 1.938 50.80

4 1/2 114.30 15.1-20.0 22.5-29.8 2 3/8 EUE 60.3 3.500 88.90 1.703 43.26

5 127.00 11.5-15.0 17.1-22.3 2 3/8 EUE 60.3 4.125 104.78 1.938 49.23

5 127.00 18.0-20.8 26.8-31.0 2 3/8 EUE 60.3 4.000 101.60 1.938 49.23

5 1/2 139.70 13.0-14.0 19.3-20.8 2 3/8 EUE 60.3 4.812 122.22 1.938 50.80

5 1/2 139.70 14.0-20.0 20.8-29.8 2 3/8 EUE 60.3 4.625 117.48 1.938 50.80

5 1/2 139.70 20.0-23.0 29.8-34.2 2 3/8 EUE 60.3 4.500 114.30 1.938 50.80

5 1/2 139.70 13.0-15.5 19.3-23.1 2 7/8 EUE 73.0 4.781 121.44 2.375 60.30

5 1/2 139.70 15.5-20.0 23.1-29.8 2 7/8 EUE 73.0 4.625 117.48 2.375 60.30

5 1/2 139.70 20.0-23.0 29.8-34.2 2 7/8 EUE 73.0 4.500 114.30 2.375 60.30

6 5/8 168.28 24.0-32.0 35.8-47.6 2 7/8 EUE 73.0 5.500 139.70 2.500 63.50

6 5/8 168.28 17.0-20.0 25.3-29.8 2 7/8 EUE 73.0 5.750 146.10 2.500 63.50

7 177.80 17.0-26.0 25.3-38.7 2 7/8 EUE 73.0 6.000 152.40 2.500 63.50

7 177.80 23.0-29.0 34.2-43.2 2 7/8 EUE 73.0 5.969 151.61 2.500 63.50

7 177.80 26.0-32.0 38.7-47.6 2 7/8 EUE 73.0 5.875 149.23 2.500 63.50

7 177.80 17.0-26.0 25.3-38.7 3 1/2 EUE 88.9 6.000 152.40 3.000 76.20

7 177.80 26.0-32.0 38.7-47.6 3 1/2 EUE 88.9 5.875 149.23 3.000 76.20

7 5/8 193.68 24.0-29.7 35.7-44.2 2 7/8 EUE 73.0 6.672 169.47 2.500 63.50

7 5/8 193.68 33.0-39.0 49.1-58.0 2 7/8 EUE 73.0 6.453 163.91 2.500 63.50

8 5/8 219.08 24.0-40.0 35.7-59.5 4 1/2 EUE 114.3 7.750 190.50 2.500 63.50

9 5/8 244.48 32.3-43.5 48.2-64.9 4 1/2 EUE 114.3 8.500 215.90 4.000 101.60

9 5/8 244.48 43.5-53.5 64.9-79.8 4 1/2 EUE 114.3 8.250 209.55 4.000 101.60

10 3/4 273.05 32.8-51.0 48.9-76.1 4 1/2 EUE 114.3 9.625 244.48 4.000 101.60

10 3/4 273.05 51.0-65.7 76.1-98.0 4 1/2 EUE 114.3 9.312 236.52 4.000 101.60

11 3/4 298.45 42.0-65.0 62.6-97.0 4 1/2 EUE 114.3 10.438 265.13 4.000 101.60

13 3/8 339.73 54.5-77.0 81.3-114.8 4 1/2 EUE 114.3 12.000 304.80 4.000 101.60



The Tryton TX-10/TX-10W are high pressure single string double grip retrievable

production packers that hold pressure from above and below. once set, the TX-10/TX-10W

can be left in tension, compression or neutral. Incorporated into the design is an internal

bypass system that along with fluid bypass while running, before the

upper slips are pulled from the casing wall.

equalizes pressure

The Packers are designed for stimulation,

service operations, production, testing, zone isolation and injection applications.

The TX-10 sets with a 1/4 right hand turn at the packer and releases with a 1/4 right hand

turn, then straight pick up. The TX-10W sets on wireline and releases with a 1/4 right hand

turn at the packer then straight pick-up. The TX-10 can be re-set multiple times whereby

once the TX-10W is released it cannot be re-set in the standard configuration.


CAN BE PACKED -OFF WITH EITHER TENSION OR COMPRESSION

OPEN J-SLOT DESIGN


LARGE INTERNAL BYPASS

TUBING CAN BE LEFT IN TENSION, COMPRESSION OR NEUTRAL


COMPATIBLE WITH A WIDE VARIETY OF TRYTON PACKER ACCESSORIES





4 1/2 114.3 9.5-13.5 14.1-20.1 2 3/8 EUE 60.3 3.750 95.25 1.938 49.23

4 1/2 114.3 13.5-15.1 20.1-22.5 2 3/8 EUE 60.3 3.656 92.86 1.938 49.23

5 127.0 11.5-15.0 17.1-22.3 2 3/8 EUE 60.3 4.125 104.78 1.938 49.23

5 127.0 18.0-20.8 26.8-31.0 2 3/8 EUE 60.3 4.000 101.60 1.938 49.23

5 1/2 139.7 14.0-20.0 20.8-29.8 2 3/8 EUE 60.3 4.625 117.48 1.938 50.80

5 1/2 139.7 20.0-23.0 29.8-34.2 2 3/8 EUE 60.3 4.500 114.30 1.938 50.80

5 1/2 139.7 13.0-15.5 19.3-23.1 2 7/8 EUE 73.0 4.781 121.44 2.375 60.30

5 1/2 139.7 15.5-20.0 23.1-29.8 2 7/8 EUE 73.0 4.625 117.48 2.375 60.30

5 1/2 139.7 20.0-23.0 29.8-34.2 2 7/8 EUE 73.0 4.500 114.30 2.375 60.30

6 5/8 168.3 24.0-32.0 35.8-47.6 2 7/8 EUE 73.0 5.500 139.70 2.500 63.50

6 5/8 168.3 17.0-20.0 25.3-29.8 2 7/8 EUE 73.0 5.750 146.10 2.500 63.50

7 177.8 17.0-26.0 25.3-38.7 2 7/8 EUE 73.0 6.000 152.40 2.500 63.50

7 177.8 23.0-29.0 34.2-43.2 2 7/8 EUE 73.0 5.969 151.61 2.500 63.50

7 177.8 26.0-32.0 38.7-47.6 2 7/8 EUE 73.0 5.875 149.23 2.500 63.50

TECHNICAL DATA



PERMAPAC PERMANENT SEAL BORE PACKERThe Tryton PermaPac Permanent Seal Bore Packer is a large bore, versatilepermanent packer that can be used for single or multiple zone completions. It is ideallysuited for HPHT and hostile environment applications as it can be readily manufacturedout of several alternative material configurations. The PermaPac can be used forvirtually any completion or production operation and can be converted into a temporarybridge plug by using a knock-out, pump-out or hydraulic disconnect bottom assembly.

The PermaPac Seal Bore Packer utilizes Tryton PermaPac seal bore accessories tomake the tubing seal as well as other options.

WIRELINE OR HYDRAULIC SET

COMPONENTS KEYED FOR MILLING

LARGE SEAL BORE

CAN BE MADE WITH VARIOUS METALLURGIES AND ELASTOMERS

CUSTOMIZED TO SUIT APPLICATIONS INCLUDING HPHTENVIRONMENTS UP TO 260°C/500°F

CASING SIZE CASING WEIGHT MAX O.D. PACKER BORE MIN. BORE THRU SEALS

in. mm lbs/ft kg/m in mm in. mm in. mm

4 1/2 114.3 9.5-13.5 14.4-20.1 3.750 95.25 2.390 60.71 1.703 43.26

4 1/2 114.3 13.5-15.1 20.1-22.5 3.594 91.29 2.500 63.50 1.901 48.29

4 1/2 114.3 9.5-13.5 14.1-20.1 3.750 95.25 2.688 68.28 1.938 49.23

5 127.0 15.0-20.8 22.3-31.0 3.968 100.79 2.390 60.71 1.703 43.26

5 127.0 15.0-20.8 22.3-31.0 3.968 100.79 2.688 68.28 1.938 49.23

5 127.0 11.5-13.0 17.1-19.3 4.250 107.95 2.688 68.28 1.938 49.23

5 1/2 139.7 13.0-17.0 19.3-25.3 4.562 115.87 2.688 68.28 1.938 49.23

5 1/2 139.7 17.0-23.0 25.3-34.2 4.437 112.70 2.688 68.28 1.938 49.23

5 1/2 139.7 13.0-17.0 19.3-25.3 4.562 115.87 3.000 76.20 2.375 60.30

5 1/2 139.7 17.0-23.0 25.3-34.2 4.437 112.70 3.000 76.20 2.375 60.30

7 177.8 23.0-32.0 34.2-47.6 5.687 144.45 3.250 82.55 2.406 61.11

7 177.8 32.0-38.0 47.6-56.5 5.468 138.89 3.250 82.55 2.406 61.11

7 177.8 17.0-20.0 25.3-29.8 6.187 157.15 3.250 82.55 2.406 61.11

7 177.8 20.0-23.0 29.8-34.2 6.000 152.40 4.000 101.60 3.000 76.20

7 177.8 26.0-29.0 38.7-43.2 5.875 149.23 4.000 101.60 3.000 76.20

7 5/8 193.7 24.0-39.0 35.7-58.0 6.625 158.75 3.250 82.55 2.406 61.11

7 5/8 193.7 24.0-33.7 35.7-50.2 6.500 165.10 4.000 101.60 3.000 76.20

7 5/8 193.7 33.7-39.0 50.2-58.0 6.125 155.58 4.000 101.60 3.000 76.20

9 5/8 244.5 29.3-53.5 43.6-79.6 8.125 206.38 3.250 82.55 2.406 61.11

9 5/8 244.5 29.3-53.5 43.6-79.6 8.125 206.38 4.000 101.60 3.000 76.20

9 5/8 244.5 29.3-53.5 43.6-79.6 8.125 206.38 4.750 120.65 3.875 98.43

9 5/8 244.5 36.0-47.0 53.6-69.9 8.438 214.33 6.000 152.40 4.875 123.83

9 5/8 244.5 40.0-58.4 60.4-86.9 8.218 208.74 6.000 152.40 4.875 123.83

TECHNICAL DATA

Common sizes shown above, other sizes may be available upon request


PERMAPAC LATCH SEAL ASSEMBLIES

The Tryton PermaPac Latch Seal Assemblies are usedfor applications in which it is desirable to land the tubingin tension, compression or neutral or where an on/offconnector, PBR or other similar device may be used.

The seal assembly is latched into the packer with setdown weight and released with right-hand rotation whileholding tension in the string.

For use with all models of seal bore packers and typicallycomes with a bottom lead in sub.

PERMAPAC LOCATOR SEAL ASSEMBLIES

The Tryton PermaPac Locator SealAssemblies are usedfor applications

. The locator seal assemblies may becombined with spacer seal units, spacer tubes, seal unitsand barrier seals to make up a longer seal assembly ifrequired for use with a seal bore extension, a PBR or aretrievable seal bore packer.

in which seal movement is necessarydue to tubing contraction or in multiple packerapplications

For use with all models of seal bore packers and typicallycomes with a bottom lead in sub.

SEAL CONFIGURATIONS CUSTOMIZED TO SUIT APPLICATIONS

CHEVRON OR BONDED SEALS AVAILABLE

SEAL MATERIALS AVAILABLE INCLUDE NITRILE, HNBR, AFLAS,RYTON, VITON, CHEMRAZ, KALREZ AND TEFLON

INCLUDING HPHT ENVIRONMENTS UP TO 260°C / 500°F


PERMAPAC SEAL UNITS

PermaPac Seal Units are designed so that the combination of seal unitswith spacer tubes and debris barriers are utilized as required in a sealbore completion design in order to ensure seal integrity is notcompromised.

The Seals can either be bonded or 'vee' seal design and are available invarious materials.

PERMAPAC TUBING ADAPTERS/CONCENTRIC COUPLINGS

PermaPac Tubing Adapters are used to allow the connection of tailpipedirectly to the bottom of the packer or seal bore extension. Tubingadapters are available for all seal assemblies and compatible tubingconnections.

PermaPac Concentric Couplings are used to join to compatible sizedseal bores to ensure proper alignment when running the seal assembly.The Concentric Coupling is available for all seal bore sizes.

PERMAPAC SEAL SPACER TUBE

PermaPac Seal Spacer Tubes are used to lengthen seal assemblies ifrequired. Spacer tubes are available in various lengths and areavailable for all seal assembly sizes.

PERMAPAC SEAL BORE EXTENSION

PermaPac Seal Bore Extensions are used to provide sufficient sealbore length so long seal assemblies may be used to accommodatetubing movement. Seal bore extensions are available for all sizes ofPermaPac packers.

Seal Bore Extensions standard lengths are 1.5 m (5 ft) and 3 m (10 ft)lengths. Other lengths may be available if required.


DESIGNED FOR BOTH VERTICAL AND HORIZONTAL APPLICATIONS

INCORPORATES A BI-DIRECTIONAL SLIP SYSTEM


UPPER AND/OR LOWER SEAL BORES AVAILABLE




CAN BE SET HYDRAULICALLY OR ON WIRELINE

VARIOUS MATERIALS AND CONNECTIONS AVAILABLE

TECHNICAL DATA

The RSB/RSB-1 Retrievable Seal Bore packer incorporates the large bore benefits of aseal bore packer with the option of retrievability. The RSB/RSB-1 can be ran for virtuallyall applications and can be used in applications whereby liner tailpipe assemblies arerequired. All load bearing parts are designed to withstand large tension loads whichmakes it ideal for both vertical and horizontal applications whereby a liner system is tobe anchored in place. The bi-directional slip system prevents both upward anddownward movement after the tool is set. The RSB/RSB-1 does not rely on settingstring weight or tension on it as it is set completely with differential hydraulic pressure orwith a wireline setting tool.

The RSB-1 has both a lower and upper seal bore in order to maximize the ID through theconnected tubing string.

The RSB/RSB-1 Packer is generally ran on the ‘RSB’ hydraulic setting tool but can beset on wireline if required. The packer is set hydraulically by applying a field adjustablepre-determined tubing differential pressure against a plugging device below the toolsuch as a pump-out plug, a wireline plug or dropping/circulating a ball from surface to aball seat sub with in the setting tool.

Once set, the RSB/RSB-1 has an internal locking mechanism to ensure the setting toolremains set until it is desired to be released. The RSB Packer has a straight pull fieldadjustable shear release.

The RSB/RSB-1 packers utilize Tryton PermaPac seal bore accessories to make thetubing seal as well as other options.

CASING SIZE CASING WEIGHT MAX TOOL O.D. LOWER BORE UPPER BORE THREAD CONNECTION

in. mm lbs/ft kg/m in. mm in. mm in. mm in. mm

7 177.8 29-32 43.15 - 47.62 5.875 149.23 4.000 101.6 4.750 120.65 4 1/2 LT&C 114.3

7 177.8 23-29 34.22-43.15 5.938 150.83 4.000 101.6 4.750 120.65 4 1/2 LT&C 114.3

7 177.8 17-23 25.30-34.22 6.188 157.18 4.000 101.6 4.750 120.65 4 1/2 LT&C 114.3

RSB/RSB-1 RETRIEVABLE SEAL BORE PACKER

On RSB-1 onlyCommon Sizes shown above, other sizes may be available upon request

*

*


The Tryton TL On/Off Tool Overshot is the disconnect/connect portion of the tool. The TLOvershot is connected to the tubing string and disconnects from the TL Slick Joint whichis connected to the tool string below. The standard overshot incorporates 2 - 4 bondedseals to ensure a reliable seal even after numerous disconnects/connects. These sealscan be made out of various materials to ensure compatibility in almost any environment.The TL On/Off Tool is normally a left hand 1/4 turn at the tool disconnect with an auto-Jon. However, a right hand disconnect option is available

The TL Overshot / Slick Joint is available in a wide range of materials and both 42 Mpa(6000psi ) and 70 Mpa (10,000psi) differential pressure rating.

The TXLOn/Off Tool incorporates an extended seal surface to allow for greater versatilitywhen running multi-packer applications. Other than being longer, the TXL On/Off Toolfunctions and has the same features of the TLOn/Off tool.

The TL On/Off Tool Slick Joint connects to a double grip packer or packer system thatdoes not require tension or compression to maintain a pack-off. The slick joint normallyhas a landing profile machined into it to serve as a receptacle for various flow controldevices.

TL ON/OFF TOOL

PROVEN RELIABLE BONDED SEAL SYSTEM

AVAILABLE IN A WIDE RANGE OF MATERIALS

42mPa (6000psi) & 70 mPa (10,000psi) PRESSURE RATINGS

NORMALLY LH RELEASE WITH OPTIONAL RH AVAILABLE

AVAILABLE

OPTIONAL THREAD CONNECTIONS AVAILABLE

LANDING PROFILE NORMALLY IN SLICK JOINT

TECHNICAL DATA

CASING SIZE MAX O.D. MIN I.D. THREAD CONNECTION

in. mm in. mm in. mm in. mm

2 7/8 73.0 2.250 57.15 1.000 25.4 1.660 EUE 42.2

3 1/2 88.9 2.750 69.85 1.500 38.1 1.900 NUE 48.3

4 101.6 3.250 82.55 1.500 38.1 1.900 EUE 48.3

4 1/2 114.3 3.750 95.25 2.000 50.8 2 3/8 EUE 60.3

5 1/2 139.7 4.500 114.3 2.000 50.8 2 3/8 EUE 60.3

5 1/2 139.7 4.500 114.3 2.500 63.5 2 7/8 EUE 73.0

7 177.8 5.750 146.0 2.500 63.5 2 7/8 EUE 73.0

7 177.8 5.750 146.0 3.000 76.2 3 1/2 EUE 88.9

8 5/8 219.1 6.500 165.1 2.500 63.5 3 1/2 EUE 88.9

8 5/8 219.1 6.500 165.1 4.000 101.6 4 1/2 EUE 114.3

9 5/8 244.5 7.500 190.5 2.500 63.5 3 1/2 EUE 88.9

9 5/8 244.5 7.500 190.5 4.000 101.6 4 1/2 EUE 114.3

10 3/4 273.1 8.500 215.9 4.000 101.6 4 1/2 EUE 114.3

Common Sizes shown above, other sizes are available upon request


TX/TXN & TOR/TORN LANDING NIPPLES

The Tryton TX/TXN and TOR/TORN Landing Nipples are utilized in the completion string toallow for the positive location of numerous subsurface flow control devices such as blankingplugs, bottom hole chokes, downhole recorders, etc.

The TX/TXN and TOR/TORN locking profiles allow for full selectivity in running flow controldevices in completion strings where numerous profile nipples may be required. The TX andTOR profiles do not have a No-Go ring machined in the bottom of the nipple where as the TXNand TORN do. Typically the No-Go nipple is the bottom profile in the string. Generally theTOR/TORN profile nipples are used in higher pressure applications or those where smallernipple sizes are required.

TX/TXN TECHNICAL DATA

TOR/TORN TECHNICAL DATA

VERSATILITY WHEN NUMEROUS PROFILES ARE REQUIRED

LARGE BORE WHERE MINIMUM RESTRICTION IS REQUIRED

SIMPLE, PROVEN DESIGN

WIDE RANGE OF MATERIALS AVAILABLE

WIDE RANGE OF SIZES AND CONNECTIONS AVAILABLE

Common Sizes shown above, other sizes are available upon requestLength and may vary if special threads are usedOD


TYPE TX TYPE TXN

TUBING O.D. SEAL BORE MIN O.D. SEAL BORE NO-GO I.D. MIN O.D.

in. mm in. mm in. mm in. mm in. mm in. mm

1.660 42.15 1.250 31.75 1.890 48.01 1.250 31.75 1.135 28.83 1.890 48.01

1.900 48.26 1.500 38.10 2.130 54.10 1.500 38.10 1.448 36.78 2.130 54.10

2.063 53.37 1.625 41.28 2.340 59.44 1.625 41.28 1.536 39.01 2.340 59.44

2.375 60.33 1.875 47.60 2.710 68.83 1.875 47.63 1.791 45.49 2.710 68.83

2.875 73.03 2.312 58.72 3.230 82.04 2.312 58.72 2.205 56.01 3.230 82.04

3.500 88.90 2.750 69.85 4.250 107.95 2.750 69.85 2.635 66.93 4.250 107.95

3.500 88.90 2.812 71.42 4.250 107.95 2.812 71.42 2.666 67.72 4.250 107.95

4.500 114.30 3.812 96.82 4.940 125.48 3.812 96.82 3.725 94.62 4.940 125.48

TYPE TOR TYPE TORN

TUBING O.D. SEAL BORE MIN O.D. SEAL BORE NO-GO I.D. MIN O.D.


2.375 60.33 1.781 45.24 3.063 77.80 1.781 45.24 1.640 41.66 3.063 77.80

2.375 60.33 1.875 47.63 3.063 77.80 1.875 47.63 1.716 43.59 3.063 77.80

2.875 73.03 2.125 53.98 3.668 93.17 2.125 53.98 1.937 49.20 3.668 93.17

2.875 73.03 2.313 58.75 3.668 93.17 2.313 58.75 2.131 54.13 3.668 93.17

3.500 88.90 2.562 65.07 4.500 114.30 2.562 65.07 2.329 59.16 4.500 114.30

TF/TR LANDING NIPPLES

TECHNICAL DATA

The Tryton TF/TR Landing Nipples are utilized in the completion string to allow for thepositive location of various subsurface flow control devices such as blanking plugs,bottom hole chokes, downhole recorders, etc.

The TF/TR Landing Nipples come in a wide range of profile sizes for each tubing sizeaccommodating those applications where numerous profile nipples may be required.The TF profile does not have a No-Go ring machined in the bottom of the nipple whereas the TR does. Typically the No-Go nipple is the bottom profile in the string.

VERSATILITY WHEN NUMEROUS PROFILES ARE REQUIRED

SIMPLE, PROVEN DESIGN

WIDE RANGE OF MATERIALS AVAILABLE

WIDE RANGE OF SIZES AND CONNECTIONS AVAILABLE



TYPE TF TYPE TR

TUBING O.D. SEAL BORE MIN O.D. SEAL BORE NO-GO I.D MIN O.D.


1.660 42.15 1.187 30.15 1.875 47.63 1.187 30.15 1.135 28.83 1.875 47.63

1.660 42.15 1.250 31.75 1.875 47.63 1.250 31.75 1.198 30.43 1.875 47.63

1.900 48.26 1.437 36.50 2.109 53.57 1.437 36.50 1.385 35.18 2.109 53.57

1.900 48.26 1.500 38.10 2.109 53.57 1.500 38.10 1.447 36.75 2.109 53.57

2.063 53.37 1.563 39.67 2.250 57.15 1.562 39.67 1.510 38.35 2.250 57.15

2.063 53.57 1.625 41.28 2.250 57.15 1.625 41.28 1.572 39.93 2.250 57.15

2.375 60.33 1.781 45.24 2.560 65.02 1.781 45.24 1.728 43.89 2.560 65.02

2.375 60.33 1.812 46.02 2.560 65.02 1.812 46.02 1.760 44.70 2.560 65.02

2.375 60.33 1.875 47.63 2.560 65.02 1.875 47.63 1.822 46.28 2.560 65.02

2.875 73.03 2.250 57.15 3.109 78.97 2.250 57.15 2.197 55.80 3.109 78.97

2.875 73.03 2.312 58.72 3.109 78.97 2.312 58.72 2.259 57.38 3.109 78.97

3.500 88.90 2.750 69.85 3.687 93.65 2.750 69.85 2.697 68.50 3.687 93.65

3.500 88.90 2.812 71.42 3.687 93.65 2.812 71.42 2.759 70.09 3.687 93.65

4.500 114.30 3.750 95.25 5.200 132.08 3.750 95.25 3.700 93.98 5.200 132.08

4.500 114.30 3.812 96.82 5.200 132.08 3.812 96.82 3.759 95.48 5.200 132.08

The Tryton TXA/TXO/TNP Sliding Sleeves are full opening devices that arean integral part of the completion string, incorporating an inner shiftablesleeve which can be opened or closed using standard wireline/coil tubingdeployed equipment and methods. All of the sleeves are designed such thatthe circulation/flow area is at least equal to the tubing size it is designed for.The standard sleeves incorporate the proven ‘vee’ seal design and can bevaried to suit the environment and/or the application it is to be used in.

The TXA and TXO both have landing profiles machined into the upperportion of the sleeve whereby the TNP does not.

The TXA and TNP shift upwards to open and the TXO shifts downward toopen. All the sleeves use a standard ‘B’shifting tool.

The sleeves are designed so that normal wireline, coil or other operationswill not open or close the sleeves inadvertently. Equalizing ports in the innersleeve allows for equalizing when shifting the sleeve open in high pressuredifferential applications.

TXA/TXO/TNP SLIDING SLEEVES


TUBING SIZE LENGTH NOM. O.D. SEAL BORE


1.90 48.3 30.75 781.1 2.375 60.30 1.500 38.10

2 1/6 55.0 31.28 794.5 2.620 66.50 1.625 41.28

2 3/8 60.3 33.32 846.2 3.090 78.49 1.875 47.63

2 7/8 73.0 36.06 915.8 3.750 95.25 2.312 58.73

3 1/2 88.9 44.80 1137.9 4.280 108.71 2.750 69.85

3 1/2 88.9 44.80 1137.9 4.280 108.81 2.810 71.37

4 1/2 114.3 51.00 1295.4 5.600 141.22 3.812 96.77

TECHNICAL DATA

RELIABLE PROVEN DESIGN

CAN BE SHIFTED MULTIPLE TIMES

PORTED AREA IS EQUAL TO THE TUBING AREA

EQUALIZING PORTS IN THE INNER SLEEVE

WIDE RANGE OF SIZES AND CONNECTIONS

TNP HAS FULL BORE ID



The Tryton TL Sliding Sleeves are full opening devices that are anintegral part of the completion string, incorporating an inner shiftablesleeve which can be opened or closed using standard wireline/coiltubing deployed equipment and methods.

The sleeves are designed so that normal wireline, coil orother operations will not open or close the sleeves inadvertently.Equalizing ports in the inner sleeve allows for equalizing when shiftingthe sleeve open in high pressure differential applications.

The sleeve has bondedseals to ensure the integrity of the seals for the extended periods oftime down hole. They can be of various elastomer types.

The upper sub has a selective TF landing nipple profile machined into itto allow for the proper shifting of the sleeve and to serve as a receptaclefor various flow control devices.

A standard D-2 Shifting Tool is used to shift the TL Sliding Sleeve openand closed.

TL SLIDING SLEEVE

TECHNICAL DATA

TUBING SIZE LENGTH SEAL BORE TOOL O.D.


2 3/8 60.33 31.97 812.04 1.781 45.23 2.910 73.91

2 3/8 60.33 31.97 812.04 1.812 46.02 2.910 73.91

2 3/8 60.33 31.97 812.04 1.875 47.63 2.910 73.91

2 7/8 73.03 35.28 896.11 2.250 57.15 3.410 86.61

2 7/8 73.03 35.28 896.11 2.312 58.72 3.410 86.61

3 1/2 88.90 37.66 956.56 2.750 69.85 4.500 114.30

3 1/2 88.90 37.66 956.56 2.812 71.42 4.500 114.30

4 1/2 114.30 46.70 1189.18 3.688 93.68 5.562 141.27

4 1/2 114.30 46.70 1189.18 3.812 96.82 5.562 141.27

RELIABLE PROVEN DESIGN

CAN BE SHIFTED MULTIPLE TIMES

PORTED AREA IS EQUAL TO THE TUBING AREA

EQUALIZING PORTS IN THE INNER SLEEVE

WIDE RANGE OF SIZES AND CONNECTIONS




TR ROTATIONAL SHEAR SAFETY JOINT

The Tryton TR Rotational Safety Joint provides foremergency release of the tubing string. The TRRotational Safety Joint uses larger square threads toseparate the upper and lower subs with right-handrotation abandoning any production equipment below.

TECHNICAL DATA

AVAILABLE IN MOST COMMON TUBING SIZES

FULL BORE I.D.

READILY FIELD ADJUSTABLE SHEAR

SHEARS BY RH ROTATION


TUBING SIZE MAX O.D. MIN I.D. THREAD CONNECTION


2 3/8 60.3 3.062 77.8 2.000 50.8 2 3/8 EUE 60.3

2 7/8 73.0 3.688 93.7 2.500 63.5 2 7/8 EUE 73.0

3 1/2 88.9 4.500 114.3 3.000 76.2 3 1/2 EUE 88.9


AVAILABLE IN MOST COMMON TUBING SIZES

FULL BORE I.D.

READILY FIELD ADJUSTABLE

SHEARS BY STRAIGHT PULL

ALLOWS FOR TORQUE TO BE TRANSMITTED THROUGH

WITHOUT AFFECTING THE SHEAR SCREWS


TQ TORQUE-THRU SHEAR SAFETY JOINT

The Tryon TQ Torque-Thru Shear Safety Joint providesfor emergency release of the tubing string. Straight pullseparates the tool at a predetermined shear value. Inaddition, the TQ Torque-Thru Shear Safety Joint allowstorque to be transmitted through the tool withoutaffecting the shear screws.

TECHNICAL DATA



1.660 42.2 2.220 56.4 1.375 34.9 1.660 EUE 42.2

1.900 48.3 2.500 63.5 1.500 38.1 1.900 EUE 48.3

2 3/8 60.3 3.062 77.8 2.000 50.8 2 3/8 EUE 60.3

2 7/8 73.0 3.688 93.7 2.500 63.5 2 7/8 EUE 73.0

3 1/2 88.9 4.500 114.3 3.000 76.2 3 1/2 EUE 88.9


TDV ANNULAR DUMP VALVE

The Tryton TDV Annular Dump Valve is an annular pressureactivated sleeve which allows for communication between theannulus and tubing, providing equalization and/or circulationas required. The TDV is not affected by tubing movement,tubing pressure or flow rate. The required annular pressure toopen the TDV is determined by the removal or addition ofshear screws.

PROVIDES ANNULAR COMMUNICATION AS REQUIRED

REQUIRED PRESSURE TO OPEN IS FIELD ADJUSTABLE

UNAFFECTED BY TUBING MOVEMENT, PRESSURE OR FLOW RATE

WIDE RANGE OF MATERIALS AND CONNECTIONS ARE AVAILABLE

TECHNICAL DATA

MAX TOOL O.D. MIN TOOL I.D. THREAD CONNECTION MAX # PINS SHEAR PIN VALUE

in. mm in. mm in. mm # psi mPa

5.688 144.48 3.781 96.04 4 1/2 LT&C 114.3 8 648 4.5

Other sizes are available upon request


Blast Joints are used to protect the tubing string from the abrasive action offlowing gas or oil when positioned opposite the perforations. Blast Joint may alsobe used directly below the well head to protect from the abrasion of doing ahydraulic fracturing operation down the annulus.

Blast Joints are made from high quality steel treated to between 28 & 36 RChardness to insure maximum abrasion resistance and strength. For H2S service,blast joints are heat treated to between 18 & 22 RC hardness as per N.A.C.E.specification MR-0175. Other materials are available on advance order ifrequired.

Full tubing I.D. is maintained through the blast joint with the O.D. the same astubing couplings. As standard, blast joints haveAPI EUE tubing connections, butcan be cut with virtually any thread connection required.

BLAST JOINTS

TECHNICAL DATA

AVAILABLE IN A WIDE RANGE OF SIZES AND CONNECTIONS

STANDARD AVAILABLE LENGTHS RANGE FROM 0.6M (2FT) TO 3.6M (12FT)

FULL BORE I.D.


TUBING SIZE MIN I.D. MAX O.D.


1.900 48.3 1.500 38.1 2.500 63.5

2 3/8 60.3 1.995 50.7 3.062 77.8

2 7/8 73.0 2.441 62.0 3.688 93.7

3 1/2 88.9 3.000 76.2 4.500 114.3

Common Sizes shown above, other sizes are available upon requestMaximum may vary if special threads are usedOD


The TB assembly is recommended when running into lines or highly deviated wells.Pump-Out Plug

PUMP OUT PLUGS

Tryton Pump-Out Plug Assemblies are used below a production packer or tailpipe. The assembly holdspressure from below and releases with a predetermined amount of tubing pressure. All of Tryton’s Pump-Out Plugs are field adjustable.

The TC assembly allows fluid flow from both directions until a ball is nonto the expendable landing seat or the ball can be ran in place allowing the tubing to fill as it isbeing ran.

dowPump-Out Plug circulated

TC PUMP OUT PLUG TECHNICAL DATA

TA PUMP OUT PLUG TECHNICAL DATA

THREADCONNECTION

MAX O.D. BODY I.D.

in. mm lbs/ft kg/m in. mm

1.660 EUE 42.2 2.200 55.88 1.250 31.75

1.900 EUE 48.3 2.500 63.50 1.500 38.10

2 3/8 EUE 60.3 3.063 77.80 2.000 50.80

2 7/8 EUE 73.0 3.750 95.25 2.500 63.50

3 1/2 EUE 88.9 4.500 114.30 3.000 76.20

TB PUMP OUT PLUG TECHNICAL DATA

THREADCONNECTION

MAX O.D. BODY I.D.

in. mm lbs/ft kg/m in. mm

1.660 EUE 42.2 2.200 55.88 1.250 31.75

1.900 EUE 48.3 2.500 63.50 1.500 38.10

2 3/8 EUE 60.3 3.063 77.80 2.000 50.80

2 7/8 EUE 73.0 3.750 95.25 2.500 63.50

3 1/2 EUE 88.9 4.500 114.30 3.000 76.20

THREADCONNECTION

MAX O.D. SEAT I.D. BODY I.D.


2 3/8 EUE 60.3 3.250 82.55 1.000 25.40 2.000 50.80

2 7/8 EUE 73.0 4.250 107.95 1.187 30.15 2.500 63.50

3 1/2 EUE 88.9 4.500 114.30 1.187 30.15 3.000 76.20

The TA is the most commonly used plug and has a solid aluminum expendable end.Pump-Out Plug

Other sizes may be available upon request




The Tryton TBD Dual Burst Disk is a field proven, debris-free, knockout plugthat is run on the bottom of the packer or tubing string. After the packer isset the wellbore is isolated below. Coil tubing, slickline, drop bar or sandline can be used to rupture the ceramic disk allowing production up thetubing with no debris interference.

ALTERNATIVE TO PROFILE NIPPLE WITH A PLUG

MAXIMUM SURGE POTENTIAL OF FORMATION AFTER RUPTURING

HIGH PRESSURE RATING - 70 mPa (10,000 PSI)

FULL OPENING AND NO DEBRIS LEFT AFTER RUPTURE

AVAILABLE IN STANDARD H S AND HIGH TEMP SERVICE2


TBD DUAL BURST DISK

THREADCONNECTION

TOOL O.D. TOOL I.D. LOWER DISKRATING

UPPER DISKRATING

in. in. mm in. mm psi mPa psi mPa

2 3/8 EUE 3.060 77.72 1.995 50.67 10,000 70 10,000 70

2 7/8 EUE 3.670 93.22 2.441 62.00 10,000 70 10,000 70

3 1/2 EUE 4.500 114.30 2.992 75.99 10,000 70 10,000 70

4 1/2 EUE 5.625 142.88 3.958 100.53 10,000 70 10,000 70

TECHNICAL DATA

Common Sizes shown above, other sizes may be available upon requestMaximum may vary if special threads are usedOD


TXJ EXPANSION JOINT

The Tryton TXJ Expansion Joint is placed in the tubing string to allow for pipecontraction or expansion. The TXJ Expansion Joint is generally ran inconjunction with retrievable or permanent type production packers.

The TXJ Expansion Joint can be splined in order to allow for left or right-hand rotation when setting or releasing packers, on/off tools, sealassemblies and other downhole equipment that may require rotation.

The TXJ has a proven stacked 'vee' seal design that can be customized tosuit almost any environment as can the expansion joint be ordered toaccommodate different length requirements, materials and connections asrequired.


STANDARD LENGTHS RANGE FROM 0.6M (2FT) TO 3M (10FT)

FULL BORE I.D.

PROVEN 'VEE' SEAL DESIGN STACK

TUBING SIZE TOOL O.D. TOOL I.D. TUBING CONNECTION

in. mm in. mm in. mm in. (mm)

2 3/8 60.3 3.25 82.55 2.00 50.80 2 3/8 EUE (60.3mm)

2 7/8 73.0 3.75 95.25 2.50 63.50 2 7/8 EUE (73.0 mm)

3 1/2 88.9 5.00 127.00 3.00 76.20 3 1/2 EUE (88.9 mm)

TECHNICAL DATA

Common Sizes shown above, other sizes may be available upon requestMaximum may vary if special threads are usedOD


The Wireline Adapter Kit is used to attach wireline set packers or any othercompatible wireline set tools to the 10/20 setting tool. Once the tool is set theadapter kit is released when the required shear force is achieved by the setting tool.

Tryton

WIRELINE ADAPTER KIT

ALLOWS FOR “PLUG-IN-PLACE” RUNNING

CAN BE USED WITH MOST COMMON BLANKING PLUG TYPES AND SIZES

USED WITH #10 OR #20 HYDRAULIC SETTING TOOL

SHEAR RELEASE AFTER TOOL IS SET

TECHNICAL DATA

CASING SIZE MAX O.D. TUBING SIZE


4 1/2 114.3 3.750 95.25 2 3/8 60.3

5 127.0 3.750 95.25 2 3/8 60.3

5 1/2 139.7 4.500 114.30 2 3/8 60.3

5 1/2 139.7 4.500 114.30 2 7/8 73.0

7 177.8 4.500 114.30 2 3/8 60.3

7 177.8 4.500 114.30 2 7/8 73.0

7 177.8 5.500 139.70 3 1/2 88.9

Common Sizes shown above, other sizes may be available upon request


TUBING SWIVEL

The Tryton tubing swivel allows surface connections to remain in placewhile the work string is rotated and moved vertically. It is primarily used inconjunction with selective treating tools to provide a means of operating theby-pass valve while the treating line is connected. canalso be used in conjunction with other Tryton equipment during varioustreating and stimulation operations.

When using the swivel, it is strongly recommended that the treating line besecured to the tubing swivel with a suitable safety chain or cable.

The tubing swivel

TECHNICAL DATA

TUBING O.D. OPERATING LOAD LINE PIPE THREAD CONNECTION

in. mm lbs. daN in. mm in. mm

2 7/8 73.0 100,000 44,500 2.00 50.8 2 7/8 EUE 73.0

3 1/2 88.9 135,000 60,000 2.00 50.8 3 1/2 EUE 88.9


CASING SCRAPER

The casing scraper is used to remove foreign matter on the inside casingwall in order to provide a smooth clean casing I.D. For running and setting packersand other sub-surface equipment.

The casing scraper features a one piece body with full 360° casing I.D. coverageprovided by six spring loaded scraper blades. The design also features a largebypass area around and between the blades for ease of circulating. Each blade issecured in its own individual pocket and ensures that all thrust and rotational forcesare absorbed directly by the one piece body. The casing scraper features leaf typeIncolloy springs behind each self-sharpening blade, providing maximum usagebefore repairs or replacement is necessary.

Tryton

TECHNICAL DATA

CASING SCRAPER BLADE DIAMETER CONNECTION

SIZE BODY O.D. MIN I.D. COLLAPSED EXTENDED API REG.

in. mm in. mm. in. mm. in. mm in. mm in. mm

4 1/2 114.30 3 1/16 77.79 1.00 25.40 3.795 96.39 4.280 108.71 2 3/8 60.3

5 127.00 3 1/16 77.79 1.00 25.40 4.151 105.44 4.636 117.75 2 3/8 60.3

5 1/2 139.70 4 3/8 111.13 1.00 25.40 4.525 114.94 5.055 128.40 2 7/8 73.0

6 5/8 142.88 5 1/2 139.70 1.25 31.75 5.400 137.16 6.238 158.45 3 1/2 88.9

7 177.80 5 1/2 139.70 1.25 31.75 5.795 147.19 6.538 166.07 3 1/2 88.9

7 5/8 193.68 5 1/2 139.70 1.25 31.75 6.500 165.10 7.243 183.97 3 1/2 88.9

8 5/8 219.08 7 1/4 184.15 2.00 50.80 7.386 187.60 8.129 206.47 4 1/2 114.3

9 5/8 244.48 7 1/4 184.15 2.25 57.15 8.379 212.83 9.254 235.05 4 1/2 114.3


The TWR/CW Bridge Plugs are a proven and reliable retrievablebridge plug. They are commonly used for zone or well isolation duringfracturing, acidizing, cement squeezing, testing or up-hole/surfacerepair operations.

The double acting slips securely anchor the Bridge Plug againstpressure differentials from above or below. The three element pack offdesign ensures reliable sealing at high pressures and temperatures.

The equalizing valve design allows pressure differential to be equalizedbefore going through the upward releasing motion. No rotation isrequired to release either the TWR or the CW Bridge Plug.

Tryton

TWR/CW BRIDGE PLUG


MAY BE RAN AND RETRIEVED ON WIRELINE, COIL OR

THREE ELEMENT SYSTEM FOR RELIABLE OPERATION

PROVEN EQUALIZING SYSTEM FOR SAFE, RELIABLE RELEASE

ONE PIECE, DOUBLE ACTING SLIPS

REQUIRES STRAIGHT PULL TO RELEASE

JOINTED PIPE

, NO ROTATION


CASINGGAUGE RING O.D.

O.D. WEIGHT I.D.


2 3/8 60.3 4.69 6.99 1.994 50.7 1.800 45.72

2 3/8 60.3 4.69 6.99 1.994 50.7 1.850 46.99

2 7/8 73.0 6.48 9.67 2.441 62.0 2.250 57.15

3 1/2 88.9 9.28 13.84 2.992 76.0 2.700 68.58

4 1/2 114.3 9.50-13.50 14.10-20.10 4.090-3.920 103.9-99.6 3.800 96.50

4 1/2 114.3 9.50-13.50 14.10-20.10 4.090-3.920 103.9-99.6 3.696 93.90

5 127.0 15.00-18.00 22.30-26.80 4.408-4.276 112.0-108.6 4.062 103.20

5 127.0 11.50-13.00 17.10-19.30 4.560-4.494 115.8-114.1 4.250 108.00

5 1/2 139.7 17.00-20.00 25.30-29.80 4.892-4.778 124.3-121.4 4.500 114.30

5 1/2 139.7 15.50-17.00 23.10-25.30 4.950-4.892 125.7-124.3 4.641 117.90

5 1/2 139.7 13.00-15.50 19.30-23.10 5.044-4.950 128.1-125.7 4.728 120.10

6 5/8 168.3 28.00-32.00 41.70-47.60 5.791-5.675 147.1-144.1 5.560 141.20

6 5/8 168.3 20.00-24.00 29.80-35.70 6.049-5.921 153.6-150.4 5.658 143.70

7 177.8 29.00-32.00 43.20-47.60 6.184-6.094 157.1-154.8 5.875 149.20

7 177.8 23.00-26.00 34.20-38.70 6.366-6.276 161.7-159.4 6.023 153.00

7 177.8 17.00-20.00 25.30-29.80 6.538-6.456 166.1-164.0 6.230 158.20

7 5/8 193.7 33.70-39.00 50.20-58.00 6.765-6.625 171.9-168.3 6.375 161.90

7 5/8 193.7 24.00-29.70 35.70-44.20 7.025-6.875 178.4-174.6 6.625 168.30

8 5/8 219.1 40.00-49.00 59.50-72.90 7.725-7.511 196.2-190.8 7.500 190.50

8 5/8 219.1 24.00-36.00 35.70-53.60 8.097-7.825 205.7-198.2 7.750 196.90

9 5/8 244.5 47.00-53.50 69.90-79.60 8.681-8.535 220.5-216.8 8.285 210.40

9 5/8 244.5 32.30-43.50 48.10-64.70 9.001-8.755 228.6-222.4 8.500 215.90

TWR/CW BRIDGE PLUGTECHNICAL DATA


The TR By-Pass Valve is a rotational circulating valvegenerally used with selective treating tools. This valve opens orcloses off communication between the tubing and the annulus.

The valve is used to bypass tubing fluid when running or retrievingselective tools, and if required can also be used for circulation offluids.

The TR By-Pass Valve features a pressure balanced sleevedesign which allows for easy operation of the valve under higherdifferential pressures. Specially designed chemical and wearresistant seals ensure reliable and trouble free operation.

Exclusive to this valve are the thrust bearings which allow for easyoperation under tension or compression loads.

The TR By-Pass Valve is opened by rotating 3 turns to the rightand closed by rotating 3 turns to the left.

Tryton

TR BY-PASS VALVE

TECHNICAL DATA

CASING O.D. VALVE O.D. VALVE I.D. THREAD CONNECTION


4 1/2 114.3 3.75 95.2 1.93 49.0 2 3/8 EUE 60.3

5 127.0 3.75 95.2 1.93 49.0 2 3/8 EUE 60.3

5 1/2 139.7 3.75 95.2 1.93 49.0 2 3/8 EUE 60.3

6 5/8 168.3 3.75 95.2 1.93 49.0 2 3/8 EUE 60.3

7 177.8 5.00 127.0 2.44 62.0 2 7/8 EUE 73.0

8 5/8 219.1 5.00 127.0 2.44 62.0 2 7/8 EUE 73.0

9 5/8 244.5 5.00 127.0 2.44 62.0 2 7/8 EUE 73.0


The TA Fluid Control Valve is a pressure actuated, hydrostatic down holevalve that is used to provide control of a hydraulic column of fluid in the tubing.The TA Fluid Control Valve is actuated by applying tubing pressure over andabove the hydrostatic pressure in the tubing. The TA Fluid Control Valve isnormally used in conjunction with selective treating tools, but may also be usedfor other applications.

Tryton

The Fluid Control Valve Seating Nipple must be run as part of the tubing string.

TA FLUID CONTROL VALVE

TECHNICAL DATA

OPERATES BY TUBING PRESSURE ONLY

ANNULUS FLUID LEVEL CHANGES DO NOT EFFECT THE VALVE

DURABLE METAL TO METAL SEAT

CALIBRATED FOR ACCURATE FIELD OPERATIONS

EQUALIZING SYSTEM TO ASSIST IN WIRELINE RETRIEVAL

TOOL CAN BE RUN IN PLACE, ON WIRELINE OR IF SUFFICIENT FLUIDIS PRESENT IN THE TUBING, DROPPED FROM SURFACE

CAN BE ADAPTED FOR 2.25"/57.15mm

SIZE BODY O.D. NOGO O.D. FISHING NECKO.D.

PULLING TOOL

in. mm in. mm in. mm in. mm in. mm

2 50.8 1.750 44.5 1.875 47.6 1.375 34.9 2” Camco JDC 2” Otis RB


STA CUP TYPE SELECTIVE TREATING ASSEMBLY

The STA cup type selective treating assembly is designed to selectivelypredetermined perforated intervals. The STAwill isolate intervals from 0.3m(12in.)to any length by the addition of standard tubing pups joints, A large built-in annularbypass, make the STA easy to run and retrieve. The STA utilizes a simple designwith heavy duty cups for reliable, proven operation.

The STA assembly is normally ran into the well with a circulating valve open to aposition just above the perforated interval to be stimulated. The circulation valve isclosed to pressure test the STA's complete assembly. Opening the circulationvalve will equalize the tubing to annulus. The STA tool can now be moved to thedesired interval to be treated. Then, after the stimulation fluid is circulated downand the valve is closed, the treatment can be performed.

Accessories with the STA could include a fluid control valve, a test packer, aretrievable bridge plug and a mechanical collar locator to customize desiredoperation.

Tryton

CASING SIZE CASING WEIGHT THIMBLE O.D. MIN I.D. THREAD CONNECTION


4 1/2 114.3 9.5-13.5 14.1-20.1 3.771 95.5 1.25 31.8 2 3/8 EUE 60.3

5 127.0 18.0-21.0 26.8-31.2 4.000 101.6 1.25 31.8 2 3/8 EUE 60.3

5 127.0 11.5-15.0 17.1-22.3 4.125 104.8 1.25 31.8 2 3/8 EUE 60.3

5 1/2 139.7 20.0-23.0 29.8-34.2 4.500 114.3 1.75 44.5 2 3/8 EUE 60.3

5 1/2 139.7 15.5-17.0 23.1-25.3 4.625 117.5 1.75 44.5 2 3/8 EUE 60.3

5 1/2 139.7 13.0-15.5 19.3-23.1 4.781 121.4 1.75 44.5 2 3/8 EUE 60.3

7 177.8 28.0-35.0 41.7-52.1 5.780 146.8 1.75 44.5 2 7/8 EUE 73.0

7 177.8 23.0-26.0 34.2-38.7 5.940 150.9 1.75 44.5 2 7/8 EUE 73.0

7 177.8 17.0-20.0 25.3-29.8 6.210 157.7 1.75 44.5 2 7/8 EUE 73.0

7 5/8 193.7 33.7-39.0 50.2-58.0 7.260 184.4 2.25 57.2 2 7/8 EUE 73.0

8 5/8 219.1 40.0-49.0 59.5-72.9 7.250 188.2 2.25 57.2 2 7/8 EUE 73.0

9 5/8 244.5 47.0-53.5 69.9-79.6 8.250 209.6 2.25 57.2 2 7/8 EUE 73.0

10 3/4 273.1 32.3-43.5 48.1-64.7 8.500 215.9 2.25 57.2 2 7/8 EUE 73.0

TECHNICAL DATA

SIMPLE DESIGN AND OPERATION

ALMOST ANY LENGTH OF SPACING CAN BE ACHIEVED

LARGE BY-PASS FOR TRIPPING

RELIABLE AND DURABLE HEAVY DUTY CUPS

VARIOUS ACCESSORIES CAN BE USED TO CUSTOMIZE OPERATION


The TFV Frac Ball Valve is a high pressure, ball type, tubing actuated

fluid control valve. The TFV Frac Ball Valve holds pressure from above and

below, rotates open or closed with ½ turn at the valve, and can be assembled

to open with right or left hand rotation making it operational with a variety of

production packers. The TFV valve applications range from tubing tester,

washing, acidizing, fracing and converting double grip production packer into

temporary bridge plug.

Tryton

TFV FRAC BALL VALVE

HOLDS PRESSURE FROM ABOVE AND BELOW

½ TURN TO OPEN AND CLOSE

ASSEMBLES FOR RIGHT OR LEFT HAND ROTATION TO OPEN

TUBING CAN BE LEFT IN TENSION, COMPRESSION OR NEUTRAL

TECHNICAL DATA

TUBING SIZE MAX O.D. MAX I.D.


2 3/8 EUE 60.3 3.771 95.78 1.750 44.45

2 7/8 EUE 73.0 5.500 127.00 2.500 25.70


The TP-1 Index Valve is used to convert a double gripmechanical set packer into a retrievable bridge plug. This allows for aflow path to be open when the overshot is attached and closed whenthe packer is set and the overshot is disconnected.

Tryton

PROVEN, RELIABLE DESIGN

BY-PASS CAN BE OPEN/CLOSED WITH OVERSHOT AFTER PACKER IS SET

TP-1 RETRIEVING TOOL

The TXP Retrieving Tool is used to control the indexing operation ofthe valve as well as the setting and releasing of the double grip packer thatis used with the TP-1 index valve.

Tryton

NO SEAL

CONTROLS THE OPERATION OF THE INDEX VALVE

CIRCULATION FLOW ON TOOLPRIOR TO OR AFTER LATCHING ONTO THE INDEX VALVE

CONTROLS THE SETTING AND RELEASING OPERATIONOF THE DOUBLE GRIP PACKER

ALLOWS FOR

TP-1 INDEX VALVE

CASING SIZE CONNECTION SIZE MAX O.D.(Ret.Tool)


4 1/2 114.3 2 3/8 EUE 60.3 3.656 92.86

4 1/2 114.3 2 3/8 EUE 60.3 3.750 95.25

5 127.0 2 3/8 EUE 60.3 3.750 95.25

5 1/2 139.7 2 3/8 EUE 60.3 4.500 114.30

7 177.8 2 7/8 EUE 73.0 5.750 146.05

7 5/8 193.7 2 7/8 EUE 73.0 6.25 158.75

8 5/8 219.1 2 7/8 EUE 73.0 7.12 180.85

9 5/8 244.5 2 7/8 EUE 73.0 8.00 203.20

9 5/8 244.5 4 1/2 EUE 114.3 8.00 203.20

TECHNICAL DATA


The Tryton TNS(10K)/TNT(15K) Compression Packers are usedfor high pressure fracturing, acidizing, squeeze cementing andtesting. These packers have an integral bypass system thatallows circulation around the packer without releasing the tool.The TNS/TNT Packers are generally used with the TNCUnloader/Circulating valve assembly which functions as abypass, circulating, and equalizing valve.

The TNS/TNT packers operate with a combination right handrotation in conjunction with compression to set and achieve packoff. Straight pick-up is all that is required to release thesepackers.

PREMIUM CARBIDE SLIPS

HYDRAULIC ACTUATED HOLD DOWN SYSTEM

AVAILABLE IN OPTIONAL J-SLOT CONFIGURATIONS

HEAVY DUTY DESIGN FOR HPHT APPLICATIONS

SIMPLE, RELIABLE AND PROVEN OPERATION

TNS/TNT COMPRESSION PACKER


TNT COMPRESSION PACKERTECHNICAL DATA

CASING SIZE CASING WEIGHT MAX O.D. MIN I.D. THREAD CONNECTIONS


4 1/2 114.3 11.6-13.5 17.26-20.1 3.750 95.25 1.500 38.10 2 3/8 EUE 60.3

4 1/2 114.3 9.5-11.6 14.1-17.26 3.813 96.85 1.500 38.10 2 3/8 EUE 60.3

5 127.0 18.0-20.8 26.8-31.0 4.000 101.60 1.750 44.45 2 3/8 EUE 60.3

5 127.0 11.5-15.0 17.1-22.3 4.125 104.78 1.750 44.45 2 3/8 EUE 60.3

5 1/2 139.7 20.0-23.0 29.8-34.2 4.500 114.30 2.000 50.80 2 3/8 EUE 60.3

5 1/2 139.7 14.0-20.0 20.8-29.8 4.625 117.48 2.000 50.80 2 3/8 EUE 60.3

7 177.8 26.0-32.0 38.7-47.6 5.875 149.23 2.300 58.42 2 7/8 EUE 73.0

7 177.8 23.0-29.0 34.2-43.2 5.969 151.61 2.300 58.42 2 7/8 EUE 73.0

7 177.8 17.0-26.0 25.3-38.7 6.000 152.40 2.300 58.42 2 7/8 EUE 73.0



4 1/2 114.3 11.6-13.5 17.26-20.1 3.750 95.25 1.875 47.63 2 3/8 EUE 60.3

4 1/2 114.3 9.5-11.6 14.1-17.26 3.813 96.85 1.875 47.63 2 3/8 EUE 60.3

5 127.0 18.0-20.8 26.8-31.0 4.000 101.60 1.875 47.63 2 3/8 EUE 60.3

5 127.0 11.5-15.0 17.1-22.3 4.125 104.78 1.875 47.63 2 3/8 EUE 60.3

5 1/2 139.7 20.0-23.0 29.8-34.2 4.500 114.30 2.000 50.80 2 3/8 EUE 60.3

5 1/2 139.7 14.0-20.0 20.8-29.8 4.625 117.48 2.000 50.80 2 3/8 EUE 60.3

7 177.8 26.0-32.0 38.7-47.6 5.875 149.23 2.500 63.50 2 7/8 EUE 73.0

7 177.8 23.0-29.0 34.2-43.2 5.969 151.61 2.500 63.50 2 7/8 EUE 73.0

7 177.8 17.0-26.0 25.3-38.7 6.000 152.40 2.500 63.50 2 7/8 EUE 73.0

7 5/8 193.7 33.7-39.0 50.2-58.0 6.453 163.91 2.500 63.50 2 7/8 EUE 73.0

7 5/8 193.7 24.0-29.7 35.7-44.2 6.688 169.88 2.500 63.50 2 7/8 EUE 73.0

9 5/8 244.5 40.0-53.5 59.5-79.6 8.250 209.60 4.000 101.60 4 1/2 EUE 114.3

9 5/8 244.5 32.3-43.5 48.1-64.7 8.500 215.90 4.000 101.60 4 1/2 EUE 114.3

TNS COMPRESSION PACKERTECHNICAL DATA


TNC UNLOADER

The Tryton TNC unloader is used with the TNS/TNT packers as abypass, circulating or equalizing valve. The TNC Unloaderoperates in conjunction with the packer, closing to the right whensetting the packer and opens with upward movement afterdisengaging the right hand J-slot.

HEAVY DUTY 15 K VERSION AVAILABLE

VARIOUS OPERATION CONFIGURATIONS AVAILABLE

SIMPLE OPERATION

J-SLOT ENSURES UNLOADER LOCKS IN CLOSED POSTION

TECHNICAL DATA



2 3/8 60.3 3.750 95.25 2.000 50.80 2 3/8 EUE 60.30

2 7/8 73.0 4.500 114.30 2.500 63.50 2 7/8 EUE 73.00

3 1/2 88.9 5.500 139.70 3.000 76.20 3 1/2 EUE 88.90


TSU-RBP RETRIEVABLE BRIDGE PLUG

The TSU-RBP is a high performance retrievable bridge plug that is designed to

isolate a portion of the well primarily for treating, testing or isolating for safety reasons.

The TSU-RBP can be ran alone or in conjunction with another packer depending upon

what objectives are required.

The TSU-RBP can be set mechanically, hydraulically or on wireline. As per the design

of the tool, it can be set shallow or deep. The tool is designed to allow for pressure

equalization before the slips are released making it ideal in conditions whereby,

pressure below may be uncertain.

Tryton

TUBING, HYDRAULIC OR WIRELINE SET

CAN BE SET SHALLOW OR DEEP

WITHSTANDS HIGH PRESSURE ABOVE AND BELOW

SIMPLE, RELIABLE RELEASING OPERATION

EQUALIZES PRESSURE BEFORE RELEASING UPPER SLIP SYSTEM

CARBIDE SLIPSAVAILABLE WITH

TECHNICAL DATA

CASING SIZE CASING WEIGHT MAX O.D. MAX O.D(RET. TOOL)

MIN I.D.(RET. TOOL)

TUBINGSIZE

in. mm lbs/ft kg/m in. mm in. mm in. mm in.

4 1/2 114.3 13.5-15.1 20.1-22.5 3.656 92.86 3.656 92.86 2.000 50.8 2 3/8 EUE

4 1/2 114.3 9.5-13.5 14.1-20.1 3.750 95.25 3.750 95.25 2.000 50.8 2 3/8 EUE

5 127.0 18.0-20.8 26.8-31.0 4.000 101.60 3.750 95.25 2.000 50.8 2 3/8 EUE

5 127.0 11.5-15.0 17.1-22.3 4.125 104.78 3.750 95.25 2.000 50.8 2 3/8 EUE

5 1/2 139.7 20.0-23.0 29.8-34.2 4.500 114.30 4.500 114.30 2.000 or 2.375 50.8 or 60.3 2 3/8 or 2 7/8 EUE

5 1/2 139.7 14.0-20.0 20.8-29.8 4.625 117.48 4.500 114.30 2.000 or 2.375 50.8 or 60.3 2 3/8 or 2 7/8 EUE

5 1/2 139.7 13.0-15.5 19.3-23.1 4.781 121.44 4.500 114.30 2.000 or 2.375 50.8 or 60.3 2 3/8 or 2 7/8 EUE

7 177.8 26.0-32.0 38.7-47.6 5.875 149.23 5.875 149.23 2.500 63.5 2 7/8 EUE

7 177.8 23.0-29.0 34.2-43.2 5.969 151.60 5.875 149.23 2.500 63.5 2 7/8 EUE

7 177.8 17.0-26.0 25.3-38.7 6.000 151.60 5.875 149.23 2.500 63.5 2 7/8 EUE

TSU RUNNING/RETRIEVING OVERSHOT

The TSU Running/Retrieving Overshot is used to set and retrieve theTSU-RBP Retrievable Bridge Plug. If the TSU-RBP is mechanically set thetypical setting procedure is RH set, RH release. If the TSU-RBP ishydraulically or wireline set, then typically it would be RH release.

Tryton


The THD Compression Packer is designed forhigh pressure fracturing, acidizing, and testing. TheTHD has an integral bypass system that allowscirculation around the packer without releasing the tool.The THD is commonly used with the TSU-RBP BridgePlug for multiple zone operations.

Tryton

THD COMPRESSION PACKER

INTERNAL BYPASS

PREMIUM CARBIDE SLIPS

HYDRAULICALLY ACTUATED HOLD DOWN SYSTEM

FULL BORE DESIGN

AVAILABLE IN SEVERAL J-SLOT CONFIGURATIONS,INCLUDING MANUAL & AUTO



4 1/2 114.3 11.6-13.5 17.3-20.1 3.750 95.25 1.875 47.63 2 3/8 EUE 60.3

4 1/2 114.3 9.5-11.6 14.1-17.3 3.813 96.85 1.875 47.63 2 3/8 EUE 60.3

5 127.0 18.0-20.8 26.8-31.0 4.000 101.60 1.875 47.63 2 3/8 EUE 60.3

5 127.0 11.5-15.0 17.1-22.3 4.125 104.78 1.875 47.63 2 3/8 EUE 60.3

5 1/2 139.7 20.0-23.0 29.8-34.2 4.500 114.30 2.000 50.80 2 3/8 EUE 60.3

5 1/2 139.7 14.0-20.0 20.8-29.8 4.625 117.48 2.000 50.80 2 3/8 EUE 60.3

7 177.8 26.0-32.0 38.7-47.6 5.875 149.23 2.500 63.50 2 7/8 EUE 73.0

7 177.8 23.0-29.0 34.2-43.2 5.969 151.61 2.500 63.50 2 7/8 EUE 73.0

7 177.8 17.0-26.0 25.3-38.7 6.000 152.40 2.500 63.50 2 7/8 EUE 73.0

7 5/8 193.7 33.7-39.0 50.2-58.0 6.453 163.91 2.500 63.50 2 7/8 EUE 73.0

7 5/8 193.7 24.0-29.7 35.7-44.2 6.688 169.88 2.500 63.50 2 7/8 EUE 73.0

9 5/8 244.5 40.0-53.5 59.5-79.6 8.250 209.60 4.000 101.60 4 1/2 EUE 114.3

9 5/8 244.5 32.3-43.5 48.1-64.7 8.500 215.90 4.000 101.60 4 1/2 EUE 114.3

TECHNICAL DATA


The T5/T10/T20 Hydraulic Setting Tools are designed to be run on drillpipe, tubing, or coil tubing. Pressure is transmitted to the setting tool in orderto set bridge plugs, cement retainers, production packers, and service toolswhich would normally be set on wireline. Hydraulically setting equipment isespecially applicable to setting plugs or packers in deviated wells or onlocations where a wireline unit is not available or practical.

The T5/T10/T20 setting tools can have setting chambers added or removeddepending upon pressure or force requirements.

Tryton

T5/T10/T20 HYDRAULIC SETTING TOOL

TECHNICAL DATA

RUN ON DRILL PIPE, TUBING OR COIL TUBING

SETTING CHAMBERS MAY BE ADDED OR REMOVED DEPENDINGON SETTING PRESSURE GENERATED

HYDRAULICALLY SET EQUIPMENT NORMALLY SET ON WIRELINE

SIZESETTING

TOOL SIZETOOL O.D.

THREADCONNECTION

in. mm # in. mm in.

1 1/2 38.1 # 5 2.13 54.10 1 1/2 NPT

2 3/8 60.3 #10 3.63 92.20 2 3/8 EUE

2 7/8 73.0 # 20 4.38 111.25 2 7/8 EUE


DB BRIDGE PLUG

CONSTRUCTED WITH READILY DRILLABLE MATERIALS

360° RETAINING RINGS TO ASSIST IN PREVENTINGELEMENT EXTRUSION (NOT AVAILABLE IN 5,000 PSI PLUG)

STANDARD VERSIONS UP TO

THERMAL VERSION AVAILABLE

70 MPA(10,000 PSI) RATED AT 150°C (300°F)


TECHNICAL DATA

The DB Bridge Plug is an economical, fully drillable,cast iron bridge plug. The DB bridge plug is designedfor well abandonments, zone suspension or isolation.

CASING SIZE CASING WEIGHT PLUG O.D. SETTING MIN. SETTING MAX. SETTING FORCE

in. mm lbs/ft kg/m in. mm in. mm in. mm lbs daN

2 3/8 60.3 4.0-5.8 6.0-8.6 1.750 44.45 1.780 45.21 2.074 52.68 13,000 5,782

2 7/8 73.0 6.4-6.5 9.5-9.7 2.220 56.39 2.340 59.44 2.525 64.14 13,000 5,782

3 1/2 88.9 5.7-10.3 8.6-14.9 2.750 69.85 2.867 72.82 3.258 82.75 13,000 5,782

4 101.6 5.6-14.0 8.3-20.8 3.140 79.76 3.340 84.84 3.732 94.79 20,000 8,896

4 1/2 114.3 9.5-15.1 14.1-22.5 3.562 90.47 3.826 97.18 4.090 103.89 33,000 14,678

5 127.0 11.5-20.8 17.1-31.0 3.937 100.00 4.154 105.51 4.560 115.82 33,000 14,678

5 1/2 139.7 13.0-23.0 19.3-34.2 4.312 109.52 4.580 116.33 5.044 128.12 33,000 14,678

5 3/4 146.0 14.0-25.2 20.8-37.5 4.699 119.35 4.890 124.21 5.290 134.37 33,000 14,678

6 5/8 168.3 17.0-32.0 25.3-48.0 5.375 136.53 5.595 142.11 6.135 155.83 50,000 22,240

7 177.8 17.0-35.0 25.3-52.1 5.687 144.45 6.000 152.40 6.538 166.07 50,000 22,240

7 5/8 193.7 20.0-39.0 29.8-58.0 6.312 160.32 6.625 168.28 7.125 180.98 50,000 22,240

8 5/8 219.1 24.0-49.0 35.7-72.9 7.125 180.98 7.310 185.67 8.097 205.66 50,000 22,240

9 5/8 244.5 29.3-58.4 43.6-86.9 8.125 206.38 8.379 212.83 9.063 230.20 50,000 22,240

10 3/4 269.9 32.7-60.7 48.7-90.3 9.437 239.70 9.660 245.36 10.192 258.88 50,000 22,240

11 3/4 298.5 38.0-60.0 56.5-89.3 10.437 265.10 10.772 273.61 11.150 283.21 50,000 22,240

11 3/4 298.5 60.0-83.0 89.3-123.5 9.937 252.40 10.192 258.88 10.772 273.61 50,000 22,240

13 3/8 339.7 48.0-84.5 71.4-125.7 11.880 301.75 12.125 307.98 12.715 322.96 50,000 22,240

16 406.4 65.0-118.0 96.7-175.5 14.125 358.78 14.125 358.78 15.250 387.35 50,000 22,240

20 508.0 94.0-133.0 139.8-197.8 18.730 475.74 18.730 475.74 19.124 485.75 50,000 22,240

* Available in both DB-5 and DB-10 Models

*

*

*

*

*

*

*

*

*

*

*

*


The Tryton HM-1B Bridge Plug is a cast-iron bridge plug set withthe combination of both hydraulic pressure and mechanical pullto abandon, suspend or isolate a zone or zones within thewellbore.

Setting the plug requires the use of a retrievable setting toolconnected to the tubing and after the plug is set it is released byright hand rotation.

CASING PLUGO.D.

SETTING RANGE

SIZE WEIGHT MIN MAX


4 1/2 114.3 9.5-15.1 14.1-22.5 3.562 90.47 3.826 97.18 4.090 103.89

5 127.0 11.5-20.8 17.1-31.0 3.937 100.00 4.154 105.51 4.560 115.82

5 1/2 139.7 13.0-23.0 19.3-34.2 4.312 109.52 4.580 116.33 5.044 128.12

7 177.8 17.0-35.0 25.3-52.1 5.687 144.45 6.000 152.40 6.538 166.07

7 5/8 193.7 20.0-39.0 29.8-58.0 6.312 160.32 6.625 168.28 7.125 180.98

8 5/8 219.1 24.0-49.0 35.7-72.9 7.125 180.98 7.310 185.67 8.097 205.66

9 5/8 244.5 39.3-58.4 43.6-86.9 8.175 207.65 8.435 214.25 9.063 230.20

10 3/4 273.1 32.7-60.7 48.7-90.3 9.437 239.70 9.660 245.36 10.192 258.88

11 3/4 298.5 38.0-60.0 56.6-89.3 10.437 265.10 10.772 273.61 11.150 283.21

11 3/4 298.5 60.0-83.0 89.3-123.5 9.937 252.40 10.192 258.88 10.772 273.61

13 3/8 339.7 48.0-85.0 71.4-126.5 11.880 301.75 12.159 308.84 12.175 309.25

16 406.4 65.0-118.0 96.7-175.6 14.125 358.78 14.576 370.23 15.250 387.35

20 508.0 94.0-133.0 139.9-197.9 18.375 466.73 18.730 475.74 19.124 485.75

HM-1B BRIDGE PLUG

AVAILABLE IN 5K AND 10K CONSTRUCTION


STANDARD VERSIONS UP TO 70 MPA(10,000 PSI) RATED @ 150°C (300°F)

THERMAL ELEMENT AVAILABLE UPON REQUEST

RIGHT HAND ROTATION TO RELEASE WORK STRING

TECHNICAL DATA


The Tryton HM-2 bridge plug is a cast-iron bridge plug set with thecombination of both hydraulic pressure and mechanical pull to abandon,suspend or isolate a zone or zones within the wellbore.

The setting tool of the HM-2 is built into the plug allowing for full ID of the workstring after the plug is set and released.

HM-2 BRIDGE PLUG


RETAINING RINGS TO ASSIST IN PREVENTING ELEMENT EXTRUSION

STANDARD VERSIONS UP TO

THERMAL ELEMENT AVAILABLE UPON REQUEST

70 MPA(10,000 PSI) RATED @ 150°C (300°F)

RIGHT HAND ROTATION TO RELEASE WORK STRING

FULL ID ON WORK STRING AFTER RELEASE FROM THE PLUG

CASING PLUG SETTING RANGE

SIZE WEIGHT O.D. MIN MAX


3 1/2 88.9 5.7-10.3 8.6-15.3 2.750 69.85 2.867 72.82 3.258 82.75

4 101.6 5.6-14.0 8.3-20.8 3.190 81.03 3.340 84.84 3.732 94.79

4 1/2 114.3 9.5-16.6 14.1-24.7 3.562 90.47 3.826 97.18 4.090 103.89

5 127 11.5-20.8 17.1-31.0 3.937 100.00 4.154 105.51 4.560 115.82

5 1/2 139.7 13.0-23.0 19.3-34.2 4.312 109.52 4.580 116.33 5.044 128.12

5 3/4 146.1 14.0-25.2 20.8-37.5 4.699 119.35 4.890 124.21 5.290 134.37

6 5/8 168.3 17.0-32.0 25.3-47.6 5.375 136.53 5.595 142.11 6.135 155.83

7 177.8 17.0-35.0 25.3-52.1 5.687 144.45 6.000 152.40 6.538 166.07

7 5/8 193.7 20.0-39.0 29.8-58.0 6.312 160.32 6.625 168.28 7.125 180.98

8 5/8 219.1 24.0-49.0 35.7-72.9 7.125 180.98 7.310 185.67 8.097 205.66

9 5/8 244.5 29.3-58.4 43.6-86.9 8.175 207.65 8.379 212.83 9.063 230.20

10 3/4 273.1 32.7-60.7 48.6-90.3 9.437 239.70 9.660 245.36 10.192 258.88

13 3/8 339.7 48.0-84.5 71.4-25.7 11.880 301.75 12.175 309.25 12.715 322.96

TECHNICAL DATA


The Tryton TCB Composite Bridge Plug is designed to be used for temporaryzone isolation for operations in both horizontal and vertical wells. Thecomposites used in construction allows for short drill time and ease ofoperation, which makes it ideal for multiple plug applications and coil tubingdrill out.

Tryton composite bridge plugs can be run with any wireline setting tool ortubing run hydraulic setting tools. Cast iron slips are hardened to wickerdepth only and set in any grade of casing.

8K OR

SETS SECURELY IN ANY HARDNESS CASING

COMPACT SIZE FOR EASY RUNNING

10K RATING READILY AVAILABLE AS STANDARD PRODUCT

HIGH TEMP RATING AVAILABLE


TCB COMPOSITE BRIDGE PLUG

TECHNICAL DATA

CASING O.D. CASING WEIGHT TOOL O.D. OVERALL LENGTH


2 3/8 60.3 4.70 7.0 1.750 44.45 16.38 416.1

2 7/8 73.0 6.40-7.90 9.5-11.8 2.150 54.61 17.50 444.5

3 1/2 88.9 7.70 11.4 2.825 71.75 17.50 444.5

3 1/2 88.9 9.30-10.20 13.8-15.2 2.725 69.22 17.50 444.5

3 1/2 88.9 12.95 19.3 2.500 63.50 17.50 444.5

4 101.6 9.50-11.00 14.1-16.4 3.188 80.98 23.88 606.6

4 1/2 114.3 9.50-13.50 14.1-20.1 3.570 90.67 23.88 606.6

4 1/2 114.3 15.10-17.10 22.5-25.4 3.440 87.38 23.88 606.6

4 1/2 114.3 18.80-20.00 28.0-29.8 3.375 85.73 23.88 606.6

5 127.0 11.50-18.00 17.1-26.8 3.920 99.57 23.88 606.6

5 1/2 139.7 14.00 20.8 4.600 116.80 23.80 604.5

5 1/2 139.7 15.50-23.00 23.1-34.2 4.300 109.22 23.80 604.5

7 177.8 17.00-20.00 25.3-29.8 5.950 151.10 24.00 609.6

7 177.8 23.00-32.00 34.2-47.6 5.750 146.05 24.00 609.6

7 5/8 193.7 24.00-33.70 35.7-50.2 6.250 158.75 24.00 609.6


TCR CEMENT RETAINER

The Tryton TCR Cement Retainer is an economical, fully drillable cementretainer. Can be either wireline or mechanical set and can utilize either a snaplatch or J-latch stinger. The TCR incorporates an internal valve which isopen/closed with up/down movement of the work string when the stinger isengaged and automatically closes when the stinger is removed.

WIRELINE OR MECHANICAL SET

COMPACT DESIGN WITH EXTRA CLEARANCE O.D.

UP TO 70 MPA (10,000 PSI) RATED @ 150°C (300°F)

POSITIVE CONTROL OF CEMENTING OPERATION WHEN STINGER IS IN PLACE

CASING SIZE CASING WEIGHT RETAINER O.D. MINIMUM MAXIMUM


4 1/2 114.3 9.5-15.1 14.1-22.5 3.593 91.26 3.826 97.18 4.091 103.89

5 127.0 11.5-20.8 17.1-31.0 3.937 100.00 4.156 105.56 4.560 115.82

5 1/2 139.7 13.0-23.0 19.3-34.2 4.312 109.52 4.580 116.33 5.044 128.12

5 3/4 146.0 14.0-25.2 20.8-37.5 4.700 119.38 4.890 124.21 5.290 134.37

6 5/8 168.3 17.0-32.0 25.3-47.6 5.375 136.53 5.595 142.11 6.135 155.83

7 177.8 17.0-35.0 25.3-52.0 5.688 144.48 6.004 152.50 6.538 166.07

7 5/8 193.7 28.0-39.0 29.8-58.0 6.312 160.32 6.625 168.28 7.125 180.98

8 5/8 219.1 24.0-49.0 35.7-72.9 7.125 180.98 7.511 190.78 8.097 206.66

9 5/8 244.5 29.3-58.4 43.6-86.9 8.125 206.38 8.435 214.25 9.063 230.20

10 3/4 273.0 32.8-60.7 48.7-90.3 9.437 239.70 9.660 245.36 10.192 258.88

11 3/4 298.5 38.0-60.0 56.5-89.3 10.437 265.10 10.772 273.61 11.150 283.21

11 3/4 298.5 60.0-83.0 89.9-123.5 9.937 252.40 10.192 258.88 10.772 273.61

13 3/8 339.7 48.0-80.7 71.4-120.0 11.875 301.63 12.175 309.25 12.715 322.96

16 406.4 65.0-118.0 96.7-175.7 14.125 358.78 14.675 373.10 15.250 387.35

20 508.0 94.0-133.0 139.8-197.8 18.375 466.73 18.730 475.74 19.124 485.75

TECHNICAL DATA


TCR MECHANICAL SETTING TOOL

The Tryton TCR Mechanical Setting Tool is used to run and set the cement retaineron tubing. In addition to the setting function the mechanical setting toolincorporates the cementing stinger that is used to operate the retainer valve oncethe retainer is set.

The TCR mechanical setting tool operates with right hand rotation in conjunctionwith compression/tension enabling the setting of the cement retainer slips andengaging the appropriate pack-off.

SIMPLE DEPENDABLE OPERATION

SAVES ON WIRELINE COST

PROVEN ONE-TRIP SYSTEM

Other sizes available upon request

CASING RETAINER MECHANICAL SETTING TOOL

SIZE WEIGHT O.D. I.D. CONNECTION


4 1/2 114.3 9.5-15.1 14.1-22.5 3.593 91.3 0.785 22.2 2.375 60.3

5 127.0 11.5-18.0 17.1-26.8 3.593 91.3 0.785 22.2 2.375 60.3

5 1/2 139.7 13.0-23.0 19.3-34.2 4.312 109.5 0.785 22.2 2.375 60.3

6 5/8 168.3 17.0-34.0 25.3-50.6 4.938 125.4 1.250 31.8 2.875 73.0

7 177.8 17.0-35.0 25.3-52.1 5.375 136.5 1.250 31.8 2.875 73.0

7 5/8 193.7 20.0-39.0 29.8-58.0 6.312 160.3 1.250 31.8 2.875 73.0

8 5/8 219.1 24.0-49.0 35.7-72.9 7.125 181.0 1.250 31.8 2.875 73.0

9 5/8 244.5 29.3-53.5 43.6-79.6 8.125 206.4 1.250 31.8 2.875 73.0

TECHNICAL DATA


TCR J-LATCH STINGERSNAP LATCH/

The Tryton TCR Snap Latch/J-latch Stingers are positive latches foroperating the sliding valve inside a cement retainer providing controlduring cementing operations.

The Snap Latch Stinger is an auto-in, snap out system, while the J-Latch Stinger is an auto-in, quarter turn right hand J-out system bothallowing for up and down valve control throughout the cementingoperation. Both have secondary release systems with the SnapLatch being a rotational release and the J-Latch a shear release.

POSITIVE AND RELIABLE LATCHING SYSTEM

ALLOWS FOR PRESSURE TESTING

SAFETY RELEASE ( /SHEAR OUT) IF REQUIRED

ALLOWS FOR POSITIVE INDICATION OF STINGER LOCATION

TUBING

ROTATE

TECHNICAL DATA

TUBING SIZE MIN I.D.

in. mm in. mm

2 3/8 EUE 60.3 0.785 19.93

2 7/8 EUE 73.0 0.785 19.93

2 7/8 EUE 73.0 1.250 31.75

Depending on casing size, appropriate centralizermay be used above the stinger


The Tryton TC-1 Drag Block Anchor Catcher is a reliable, retrievable doublegrip anchor catcher which prevents excessive movement of the tubing stringduring pumping operation increasing pump efficiency and decreasing rod andtubing wear.

TC-1 DRAG BLOCK TUBING ANCHOR/CATCHER

STANDARD LH SET WITH OPTIONAL RH AVAILABLE

RETRIEVABLE BY RH ROTATION WITH OPTIONAL LH AVAILABLE

EFFICIENT AND RELIABLE DRAG BLOCK AND SLIP SYSTEM

FIELD ADJUSTABLE EMERGENCY SHEAR RELEASE

TECHNICAL DATA

CASING ANCHOR

MAX O.D. WEIGHT MIN I.D. ANCHOR O.D. ANCHOR I.D. THREAD CONNECTION

in. mm lbs/ft kg/m in. mm in. mm in. mm in. (mm)

4 1/2 114.3 9.5-13.5 14.1-20.1 3.920 99.6 3.75 95.25 1.93 49.0 2 3/8 (60.3 mm) EUE

5 127.0 11.5-18.0 17.1-26.8 4.276 108.6 4.12 104.60 1.93 49.0 2 3/8 (60.3 mm) EUE

5 1/2 139.7 20.0-26.0 29.8-38.7 4.548 115.5 4.50 114.30 1.93 49.0 2 3/8 (60.3 mm) EUE

5 1/2 139.7 13.0-17.0 19.3-25.3 4.892 124.3 4.62 117.30 1.93 49.0 2 3/8 (60.3 mm) EUE

5 1/2 139.7 20.0-26.0 29.8-38.7 4.548 115.5 4.50 114.30 2.44 62.0 2 7/8 (73.0 mm) EUE

5 1/2 139.7 13.0-17.0 19.3-25.3 4.892 124.3 4.62 117.30 2.44 62.0 2 7/8 (73.0 mm) EUE

7 177.8 23.0-38.0 34.2-56.6 5.920 150.4 5.88 149.40 2.44 62.0 2 7/8 (73.0 mm) EUE

7 177.8 17.0-20.0 25.3-29.8 6.456 164.0 6.25 158.70 2.99 76.0 3 1/2 (88.9 mm) EUE

8 5/8 219.1 24.0-49.0 35.7-72.9 7.511 190.8 7.00 177.80 3.00 76.2 3 1/2 (88.9 mm) EUE

9 5/8 244.5 32.3-47.0 48.1-69.9 8.681 220.5 8.25 209.60 3.00 76.2 3 1/2 (88.9 mm) EUE


The Tryton HC Anchor Catcher is designed to anchor the tubing string frommovement in tension, compression or rotation. The benefits of placing the tubingstring in tension is to ensure that the tubing follows the rod string as close aspossible to minimize rod wear.

To operate, the HC Anchor Catcher is normally right hand set and left handrelease or it has a secondary field adjustable shear release.

HC ANCHOR CATCHER

RH SET, LH RELEASE

FULL BORE ID


OPEN DESIGN FOR GAS AND DOWNHOLE FILL TO BY-PASS

INCONEL SPRINGS FOR H2S AND CO2 COMPATIBILITY

CASING SIZE CASING WEIGHT BODY MAX O.D. MIN I.D. THREAD CONNECTION

in. mm lbs/ft kg/m in. mm in. mm in. (mm)

5 1/2 139.7 13.0 - 20.0 19.38 - 29.83 4.50 114.3 1.990 50.54 2 3/8 ( 60.3 ) EUE

7 177.8 17.0 - 26.0 25.35 - 38.78 6.00 152.4 2.440 61.98 2 7/8 ( 73.0 ) EUE

8 5/8 219.1 20.0 - 36.0 29.83 - 53.69 7.63 193.8 3.000 76.20 3 1/2 ( 88.9 ) EUE

9 5/8 244.4 32.0 - 53.5 47.72 - 79.79 8.25 209.6 3.000 76.20 3 1/2 ( 88.9 ) EUE

TECHNICAL DATA


CASING SIZE CASING WEIGHT MAX TOOL O.D. LINER SIZE


7 177.8 20.0-26.0 29.8-38.7 5.875 149.2 4 1/2 114.3

7 177.8 26.0-32.0 38.7-47.6 5.750 146.1 4 1/2 114.3

8 5/8 219.1 24.0-32.0 35.7-47.6 7.610 193.3 5 1/2 139.7

8 5/8 219.1 32.0-40.0 47.6-59.5 7.375 187.3 5 1/2 139.7

9 5/8 244.5 29.3-40.0 43.6-59.5 8.452 214.7 7 177.8

9 5/8 244.5 40.0-47.0 59.5-69.9 8.375 212.7 7 177.8

9 5/8 244.5 43.5-53.5 64.7-79.6 8.187 208.0 7 177.8

TLP/ LINER PACKERTLH

The Tryton TLP/TLH Liner Packers are a simple, inexpensivemeans of running and packing off above a liner that is suspendedbelow.

The TLP/TLH Liner Packers are compression activated and are setafter disconnecting mechanically by right hand rotation or by ahydraulic disconnect then setting back down on the packer with therunning dogs to activate the elements.

either

COMPACT DESIGN

SIMPLE OPERATION

MECHANICAL OR HYDRAULIC SET

FULL BORE

HIGH TENSILE LOAD CAPACITY

TECHNICAL DATA


COST EFFECTIVE

NO PERMANENT RESTRICTION

HELPS PREVENT GAS LOCKS

PATCH SPACING ADJUSTABLE TO ANY LENGTH

TECHNICAL DATA

The Tryton Gas Vent Casing Patch is a simple, cost effective method ofisolating casing leaks or non-productive zones. The Gas VentRetrievable Casing Patch will allow the capability of providingcommunication past the isolated section while at the same time retainisolation where required. The interval between cups is adjustable to anylength.

CASING SIZE CASING WEIGHT MAX TOOL O.D. TUBING SIZE


4 1/2 114.3 9.5-11.6 14.1-17.3 3.750 95.30 2.375 60.3

5 1/2 139.7 14.0-17-0 20.8-25.3 4.625 117.50 2.375 60.3

5 1/2 139.7 14.0-17-0 20.8-25.3 4.625 117.50 2.875 73.0

7 177.8 17.0-20.0 25.3-29.8 6.250 158.75 2.375 60.3

7 177.8 17.0-20.0 25.3-29.8 6.250 158.75 2.875 73.0

7 177.8 17.0-20.0 25.3-29.8 6.250 158.75 3.500 88.9

7 177.8 23.0-26.0 34.2-38.6 6.000 152.40 2.375 60.3

7 177.8 23.0-26.0 34.2-38.6 6.000 152.40 2.875 73.0

7 177.8 23.0-26.0 34.2-38.6 6.000 152.40 3.500 88.9

GAS VENT RETRIEVABLE CASING PATCH


The RCP Retrievable Casing Patch is designed to straddle damaged areasand/or undesired zones in the casing. The large bore design of the RCP allowsfor larger tubing string sizes if required. The system can be incorporated with adisconnect on the upper section allowing for the assembly to be installed with awork string, which once set, can be removed and the production string ran inplace. The patch length can be virtually any length as required.

The RCP can be set mechanically or hydraulically andis released simply by engaging a spear into the I.D. of the tool and jarring up.

Retrievable Casing Patch

RCP CASING PATCH

SIMPLE OPERATION

FULL BORE DESIGN

PATCH LENGTH CAN BE VARIED AS REQUIRED

DEEP WIDE WICKER SLIPS

INTERNAL RATCHET SYSTEM TO LOCK-IN SET/PACK-OFF

STAINLESS STEEL SLIP ARMS AND DRAG SPRINGS

MECHANICAL OR HYDRAULIC SET

JAR UP TO RELEASE

TECHNICAL DATA

CASING SIZE MAX O.D. MIN I.D THREAD CONNECTION


5 1/2 139.7 4.750 120.70 3.500 88.9 4 NUE 101.60

7 177.8 6.125 155.58 5.000 127.0 5 1/2 ST&C 139.70

7 177.8 6.250 158.75 5.000 127.0 5 1/2 ST&C 139.70

8 5/8 219.1 8.500 215.90 6.538 166.1 7 ST&C 177.80


The TSB Pump Tubing Bailer is a fast and efficient way toclean out sand or other fill from a well. It is an efficient mechanicalpump capable of removing large volumes of fill in a single run. TheTSB Pump Tubing Bailer does not depend on hydrostaticdifferential pressure in order to operate and is effective in low fluidwells.

The debris chamber is adjustable to accommodate any amount ofsand or fill to be retrieved. The bailer assembly is designed withcirculating drain ports eliminating the pulling of wet strings.

An optional hard faced drilling washover shoe on bottom ofassembly allows rotation through compacted sand if required.

The TSB Pump BailerAssembly is made up on the tubing string withthe required amount of chamber between the pump assembly andthe valve assembly.

Tryton

TSB PUMP TUBING BAILER

HEAVY DUTY CONSTRUCTION

OPERATION SIMPLICITY

CIRCULATING DRAIN VALVE ELIMINATES WET TRIPS

ECONOMICAL

CLEANOUT CAN BE ACCOMPLISHED IN ONE RUN

CASING SIZE MAX O.D. MIN I.D THREAD CONNECTION


4 1/2 114.3 3.125 79.38 1.00 25.40 2 3/8 EUE 60.3

5 1/2 139.7 3.750 95.25 1.25 31.75 2 7/8 EUE 73.0

7 177.8 3.750 95.25 1.25 31.75 2 7/8 EUE 73.0

7 177.8 4.500 114.30 2.50 63.50 3 1/2 EUE 89.0


CYCLONE VENTURI SYSTEM

The Tryton Cyclone Venturi System is used to remove sand, pyrite, oil, water,mud or any other foreign debris from the formation to better increaseproduction. To operate, the Cyclone Venturi is connected to the productiontubing and then lowered into the wellbore so that the 'ER' Cup Packer is spacedout above the formation.

An air/foam/water/nitrogen mixture is injected down the annulus against thecups of the ‘ER’ Packer passing through a series of angled orifices within theCyclone Venturi then through the Venturi throat and up to the surface throughthe interior of the production tubing along with wellbore effluent. The wellboreeffluent is drawn up by the vacuum created within the centre of the Venturiwhereby it is co-mingled with the injection mixture and drawn to the surfacethrough the tubing.

The ER Cup Packer is situated below the Cyclone Venturi to ensure theinjection mixture, which is under pressure, never reaches the hydrocarbonformation and eliminates fluid losses in low fluid level wells.

ECONOMICALLY AND EFFECTIVELY CLEANS OUTWELLBORES WHILE MINIMIZING RISK OF DAMAGETO SENSITIVE ZONES

HIGHER VOLUME OF FLUID RECOVERED OUT OF WELLTHAN CONVENTIONAL CLEAN OUTS / DOWNHOLEPUMPS

INCREASES PRODUCTION AFTER CLEANOUT

CAN BE USED TO EVALUATE A ZONE TO DETERMINEPROPER PUMP SIZES

UTILIZED FOR NEW COMPLETIONS FOR INITIAL SANDCLEANOUT OR FOR SUBSEQUENT CLEANOUT ONWORKOVERS

WILL ALLOW FOR LARGER DEBRIS CLEAN OUT


TPL Powerlift Jet PumpJET BENEFITS

TPL POWERLIFT JET PUMP SYSTEMS

DETERMINE INFLOW PRODUCTIONSWATER CUT %SECONDARY LIFT DESIGN

SAFELY CONTAINED HANDLING OF FLUIDSECONOMICAL COSTHIGH FLUID VOLUMESWIRELINE RETRIEVABLEPUMP OUT OPTION AVAILABLENO MOVING PARTSMULTIPLE INTERVAL TESTINGVARIABLE PRODUCTION RATESCONSTANT RESERVOIR DRAW DOWNRESERVOIR RECOVERY DATA (BUILD-UP)WATER SHUT-OFF INFORMATIONACID/CHEMICAL TREATING COMPATIBLECROSS-FLOW DETECTION

DETERMINEDETERMINE


PST SAFE TENSION TOOL

The PST was designed to safely set tubing anchors and other down hole toolsin tension under live well conditions and maintain full bore through the tubingstring.

Installed between the tubing hanger and the production tubing, the PST allowsfor full left or right rotation of the tubing. This provides for the ability to pulltension into the tubing string and lock it safely into position, all with the tubinghanger landed and locked into place, keeping complete well control.

HIGH TENSILE PULL RATING

FULL BORE ID

35 MPA MAX W.P.

SAFE AND SIMPLE METHOD OF SETTING TOOLS IN TENSION

NO NEED FOR LOW PROFILE SLIPS

CASING SIZE MAX O.D. MIN I.D MIN LENGTH MAX LENGTH

in. mm in. mm in. mm in. m in. m

2 3/8 60.3 3.875 98.4 2.000 50.8 76.4 1.94 87.0 2.21

2 7/8 73.0 4.500 114.3 2.441 62.0 76.4 1.94 87.0 2.21

TECHNICAL DATA


SGS GAS SEPARATOR

CASING SIZE CASING WEIGHT MAX O.D. MIN I.D INNER TUBING THREAD CONNECTION

in. mm lbs/ft kg/m in. mm in. mm in. mm in. mm

4 1/2 114.3 9.5-11.6 14.17-17.30 3.500 88.90 1.500 38.10 1.900 EUE 48.26 2 3/8 EUE 60.3

5 1/2 139.7 13.0-23.0 19.39-34.30 3.500 88.90 1.992 50.60 2 3/8 EUE 60.33 2 3/8 - 2 7/8 EUE 60.3-73.0

7 177.8 17.0-34.0 25.35-50.71 5.000 127.00 1.992 50.60 2 3/8 EUE 60.33 2 3/8 - 3 1/2 EUE 60.3-88.9

7 177.8 29.0-34.0 43.25-50.71 5.875 149.23 2.441 62.00 2 3/8 -2 7/8 EUE 60.3-73.0 2 3/8 - 3 1/2 EUE 60.3-88.9

7 177.8 17.0-28.0 25.3-41.66 6.000 152.40 2.441 62.00 2 3/8 -2 7/8 EUE 60.3-73.0 2 3/8 - 3 1/2 EUE 60.3-88.9

Lengths are optional

TECHNICAL DATA

The Tryton SGS Gas Separator is designed as a continuous flowdownhole gas separator to be used in conjunction with ProgressiveCavity Pumps. Utilizing centrifugal forces to separate the gas fromthe liquids before they enter the pump allows for the liquids to becarried through into the pump suction while the separated gasesmigrate up the annulus. The SGS Gas Separator has greaterliquid/gas capacities and are generally more efficient than otherdown hole gas separators.

The SGS is ran just below the pump and is ideal for wells operating atlow efficiency due to poor gas separation down hole. Separation ofgas from the liquids will generally increase well efficiency and extendthe life of the PC Pump.

DESIGNED TO OPTIMIZE GAS SEPARATION

HIGH CAPACITY

INCREASED WELL EFFICIENCY

INCREASED PC PUMP LIFE


Documents

Tryton 2012 Final wo tab… · The Tryton Open Hole Centralizer is mainly used with Tryton Open Hole Packers, generally as part of the Tryton Multi-Stage Frac System. The Centralizer