TS 134 229-1 - V14.0.0 - Universal Mobile ... · This Technical Specification (TS) has been produced by ETSI 3rd Generation Partnership Project (3GPP). The present document may refer

ETSI TS 134 229-1 V14.0.0 (2017-10)

Universal Mobile Telecommunications System (UMTS); LTE;

Internet Protocol (IP) multimedia call control protocol based on Session Initiation Protocol (SIP)

and Session Description Protocol (SDP); User Equipment (UE) conformance specification;

Part 1: Protocol conformance specification (3GPP TS 34.229-1 version 14.0.0 Release 14)

TECHNICAL SPECIFICATION

ETSI

ETSI TS 134 229-1 V14.0.0 (2017-10)13GPP TS 34.229-1 version 14.0.0 Release 14

Reference RTS/TSGR-0534229-1ve00

Keywords LTE,UMTS

ETSI

650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C

Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88

Important notice

The present document can be downloaded from: http://www.etsi.org/standards-search

The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any

existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.

Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at

https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx

If you find errors in the present document, please send your comment to one of the following services: https://portal.etsi.org/People/CommiteeSupportStaff.aspx

Copyright Notification

No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI.

The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media.

© ETSI 2017.

All rights reserved.

DECTTM, PLUGTESTSTM, UMTSTM and the ETSI logo are trademarks of ETSI registered for the benefit of its Members. 3GPPTM and LTE™ are trademarks of ETSI registered for the benefit of its Members and

of the 3GPP Organizational Partners. oneM2M logo is protected for the benefit of its Members.

GSM® and the GSM logo are trademarks registered and owned by the GSM Association.

http://www.etsi.org/standards-searchhttps://portal.etsi.org/TB/ETSIDeliverableStatus.aspxhttps://portal.etsi.org/People/CommiteeSupportStaff.aspx

ETSI


Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (https://ipr.etsi.org/).

Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document.

Foreword This Technical Specification (TS) has been produced by ETSI 3rd Generation Partnership Project (3GPP).

The present document may refer to technical specifications or reports using their 3GPP identities, UMTS identities or GSM identities. These should be interpreted as being references to the corresponding ETSI deliverables.

The cross reference between GSM, UMTS, 3GPP and ETSI identities can be found under http://webapp.etsi.org/key/queryform.asp.

Modal verbs terminology In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and "cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions).

"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.

https://ipr.etsi.org/http://webapp.etsi.org/key/queryform.asphttps://portal.etsi.org/Services/editHelp!/Howtostart/ETSIDraftingRules.aspx

ETSI


Contents

Intellectual Property Rights ................................................................................................................................ 2

Foreword ............................................................................................................................................................. 2

Modal verbs terminology .................................................................................................................................... 2

Foreword ........................................................................................................................................................... 29

Introduction ...................................................................................................................................................... 29

1 Scope ...................................................................................................................................................... 30

2 References .............................................................................................................................................. 30

3 Definitions, symbols and abbreviations ................................................................................................. 36 3.1 Definitions ........................................................................................................................................................ 36 3.2 Symbols ............................................................................................................................................................ 36 3.3 Abbreviations ................................................................................................................................................... 36

4 Overview ................................................................................................................................................ 37 4.1 Test Methodology............................................................................................................................................. 37 4.1.1 Testing of optional functions and procedures ............................................................................................. 37 4.2 Implicit Testing ................................................................................................................................................ 37 4.3 Conformance Requirements ............................................................................................................................. 37

5 Reference Conditions ............................................................................................................................. 37 5.1 Generic setup procedures ................................................................................................................................. 37 5.2 Transport protocols applied .............................................................................................................................. 37

6 PDP Context Activation ......................................................................................................................... 38 6.1 General Purpose PDP Context Establishment .................................................................................................. 38 6.2 General Purpose PDP Context Establishment (UE Requests for a Dedicated PDP Context)........................... 38 6.2.1 Definition .................................................................................................................................................... 38 6.2.2 Conformance requirement .......................................................................................................................... 38 6.2.3 Test purpose ................................................................................................................................................ 39 6.2.4 Method of test ............................................................................................................................................. 39 6.2.5 Test requirements ........................................................................................................................................ 40 6.3 Dedicated PDP Context Establishment ............................................................................................................ 40 6.3.1 Definition .................................................................................................................................................... 40 6.3.2 Conformance requirement .......................................................................................................................... 40 6.3.3 Test purpose ................................................................................................................................................ 41 6.3.4 Method of test ............................................................................................................................................. 41 6.3.5 Test requirements ........................................................................................................................................ 43

7 P-CSCF Discovery ................................................................................................................................. 43 7.1 P-CSCF Discovery via PDP Context................................................................................................................ 43 7.1.1 Definition .................................................................................................................................................... 43 7.1.2 Conformance requirement .......................................................................................................................... 43 7.1.3 Test purpose ................................................................................................................................................ 45 7.1.4 Method of test ............................................................................................................................................. 45 7.1.5 Test requirements ........................................................................................................................................ 47 7.2 P-CSCF Discovery via DHCP – IPv4 .............................................................................................................. 47 7.2.1 Definition .................................................................................................................................................... 47 7.2.2 Conformance requirement .......................................................................................................................... 47 7.2.3 Test purpose ................................................................................................................................................ 48 7.2.4 Method of test ............................................................................................................................................. 48 7.2.5 Test requirements ........................................................................................................................................ 51 7.3 P-CSCF Discovery via DHCP – IPv4 (UE Requests P-CSCF discovery via PCO) ......................................... 51 7.3.1 Definition .................................................................................................................................................... 51 7.3.2 Conformance requirement .......................................................................................................................... 51 7.3.3 Test purpose ................................................................................................................................................ 53 7.3.4 Method of test ............................................................................................................................................. 53

ETSI


7.3.5 Test requirements ........................................................................................................................................ 56 7.4 P-CSCF Discovery by DHCP - IPv6 ................................................................................................................ 57 7.4.1 Definition .................................................................................................................................................... 57 7.4.2 Conformance requirement .......................................................................................................................... 57 7.4.3 Test purpose ................................................................................................................................................ 58 7.4.4 Method of test ............................................................................................................................................. 58 7.4.5 Test requirements ........................................................................................................................................ 62 7.5 P-CSCF Discovery by DHCP-IPv6 (UE Requests P-CSCF discovery by PCO) ............................................. 62 7.5.1 Definition .................................................................................................................................................... 62 7.5.2 Conformance requirement .......................................................................................................................... 63 7.5.3 Test purpose ................................................................................................................................................ 64 7.5.4 Method of test ............................................................................................................................................. 64 7.5.5 Test requirements ........................................................................................................................................ 69 7.6 P-CSCF Discovery by DHCP – IPv6 (UE does not Request P-CSCF discovery by PCO, SS includes P-

CSCF Address(es) in PCO) .............................................................................................................................. 69 7.6.1 Definition .................................................................................................................................................... 69 7.6.2 Conformance requirement .......................................................................................................................... 69 7.6.3 Test purpose ................................................................................................................................................ 70 7.6.4 Method of test ............................................................................................................................................. 70 7.6.5 Test requirements ........................................................................................................................................ 75 7.7 Void .................................................................................................................................................................. 75 7.8 Void .................................................................................................................................................................. 75 7.9 Void .................................................................................................................................................................. 75

8 Registration ............................................................................................................................................ 75 8.1 Initial registration ............................................................................................................................................. 76 8.1.1 Definition .................................................................................................................................................... 76 8.1.2 Conformance requirement .......................................................................................................................... 76 8.1.3 Test purpose ................................................................................................................................................ 87 8.1.4 Method of test ............................................................................................................................................. 88 8.1.5 Test requirements ........................................................................................................................................ 88 8.2 User Initiated Re-Registration .......................................................................................................................... 89 8.2.1 Definition .................................................................................................................................................... 89 8.2.2 Conformance requirement .......................................................................................................................... 89 8.2.3 Test purpose ................................................................................................................................................ 91 8.2.4 Method of test ............................................................................................................................................. 92 8.2.5 Test requirements ........................................................................................................................................ 94 8.3 Mobile Initiated Deregistration ........................................................................................................................ 94 8.3.1 Definition .................................................................................................................................................... 94 8.3.2 Conformance requirement .......................................................................................................................... 95 8.3.3 Test purpose ................................................................................................................................................ 97 8.3.4 Method of test ............................................................................................................................................. 97 8.3.5 Test Requirements ...................................................................................................................................... 97 8.4 Invalid behaviour- 423 Interval too brief ......................................................................................................... 97 8.4.1 Definition .................................................................................................................................................... 97 8.4.2 Conformance requirement .......................................................................................................................... 98 8.4.3 Test purpose ................................................................................................................................................ 98 8.4.4 Method of test ............................................................................................................................................. 98 8.4.5 Test requirements ........................................................................................................................................ 99 8.5 to 8.9 Void ................................................................................................................................................................ 100 8.10 Initial registration using GIBA ....................................................................................................................... 100 8.10.1 Definition .................................................................................................................................................. 100 8.10.2 Conformance requirement ........................................................................................................................ 100 8.10.3 Test purpose .............................................................................................................................................. 104 8.10.4 Method of test ........................................................................................................................................... 105 8.10.5 Test requirements ...................................................................................................................................... 106 8.11 Initial registration using IMS AKA and GIBA against a network with GIBA support only .......................... 106 8.11.1 Definition .................................................................................................................................................. 106 8.11.2 Conformance requirement ........................................................................................................................ 106 8.11.3 Test purpose .............................................................................................................................................. 112 8.11.4 Method of test ........................................................................................................................................... 112 8.11.5 Test requirements ...................................................................................................................................... 114

ETSI


8.12 User initiated re-registration using GIBA ...................................................................................................... 114 8.12.1 Definition .................................................................................................................................................. 114 8.12.2 Conformance requirement ........................................................................................................................ 114 8.12.3 Test purpose .............................................................................................................................................. 116 8.12.4 Method of test ........................................................................................................................................... 116 8.12.5 Test requirements ...................................................................................................................................... 118 8.13 User initiated de-registration using GIBA ...................................................................................................... 118 8.13.1 Definition .................................................................................................................................................. 118 8.13.2 Conformance requirement ........................................................................................................................ 118 8.13.3 Test purpose .............................................................................................................................................. 119 8.13.4 Method of test ........................................................................................................................................... 120 8.13.5 Test requirements ...................................................................................................................................... 120 8.14 Initial registration for three implicit registration sets ..................................................................................... 120 8.14.1 Definition .................................................................................................................................................. 120 8.14.2 Conformance requirement ........................................................................................................................ 120 8.14.3 Test purpose .............................................................................................................................................. 121 8.14.4 Method of test ........................................................................................................................................... 121 8.14.5 Test requirements ...................................................................................................................................... 123 8.15 Refresh for ISIM parameters .......................................................................................................................... 123 8.15.1 Definition .................................................................................................................................................. 123 8.15.2 Conformance requirement ........................................................................................................................ 123 8.15.3 Test purpose .............................................................................................................................................. 124 8.15.4 Method of test ........................................................................................................................................... 124 8.15.5 Test requirements ...................................................................................................................................... 125 8.16 User initiated re-registration - 423 Interval Too Brief .................................................................................... 126 8.16.1 Definition .................................................................................................................................................. 126 8.16.2 Conformance requirement ........................................................................................................................ 126 8.16.3 Test purpose .............................................................................................................................................. 126 8.16.4 Method of test ........................................................................................................................................... 126 8.16.5 Test requirements ...................................................................................................................................... 128

9 Authentication ...................................................................................................................................... 128 9.1 Invalid Behaviour – MAC Parameter Invalid ................................................................................................. 128 9.1.1 Definition .................................................................................................................................................. 128 9.1.2 Conformance requirement ........................................................................................................................ 128 9.1.3 Test purpose .............................................................................................................................................. 129 9.1.4 Method of test ........................................................................................................................................... 129 9.1.5 Test requirements ...................................................................................................................................... 132 9.2 Invalid Behaviour – SQN out of range ........................................................................................................... 132 9.2.1 Definition .................................................................................................................................................. 132 9.2.2 Conformance requirement ........................................................................................................................ 132 9.2.3 Test purpose .............................................................................................................................................. 133 9.2.4 Method of test ........................................................................................................................................... 133 9.2.5 Test requirements ...................................................................................................................................... 135

10 Subscription .......................................................................................................................................... 136 10.1 Invalid Behaviour – 503 Service Unavailable ................................................................................................ 136 10.1.1 Definition .................................................................................................................................................. 136 10.1.2 Conformance requirement ........................................................................................................................ 136 10.1.3 Test purpose .............................................................................................................................................. 136 10.1.4 Method of test ........................................................................................................................................... 136 10.1.5 Test requirements ...................................................................................................................................... 137

11 Notification ........................................................................................................................................... 137 11.1 Network-initiated deregistration ..................................................................................................................... 137 11.1.1 Definition .................................................................................................................................................. 137 11.1.2 Conformance requirement ........................................................................................................................ 138 11.1.3 Test purpose .............................................................................................................................................. 138 11.1.4 Method of test ........................................................................................................................................... 138 11.1.5 Test requirements ...................................................................................................................................... 140 11.2 Network initiated re-authentication ................................................................................................................ 140 11.2.1 Definition .................................................................................................................................................. 140 11.2.2 Conformance requirement ........................................................................................................................ 140

ETSI


11.2.3 Test purpose .............................................................................................................................................. 140 11.2.4 Method of test ........................................................................................................................................... 141 11.2.5 Test requirements ...................................................................................................................................... 143

12 Call Control .......................................................................................................................................... 143 12.1 Void ................................................................................................................................................................ 143 12.2 MO Call – 503 Service Unavailable ............................................................................................................... 143 12.2.1 Definition .................................................................................................................................................. 143 12.2.2 Conformance requirement ........................................................................................................................ 143 12.2.3 Test purpose .............................................................................................................................................. 143 12.2.4 Method of test ........................................................................................................................................... 144 12.2.5 Test requirements ...................................................................................................................................... 144 12.2a MO Call – 504 Server Time-out ..................................................................................................................... 145 12.2a.1 Definition .................................................................................................................................................. 145 12.2a.2 Conformance requirement ........................................................................................................................ 145 12.2a.3 Test purpose .............................................................................................................................................. 145 12.2a.4 Method of test ........................................................................................................................................... 145 12.2a.5 Test requirements ...................................................................................................................................... 146 12.3 to 12.11 Void ........................................................................................................................................................... 146 12.12 MO MTSI Voice Call Successful with preconditions .................................................................................... 146 12.12.1 Definition .................................................................................................................................................. 146 12.12.2 Conformance requirement ........................................................................................................................ 147 12.12.3 Test purpose .............................................................................................................................................. 153 12.12.4 Method of test ........................................................................................................................................... 153 12.12.5 Test requirements ...................................................................................................................................... 153 12.13 MT MTSI speech call ..................................................................................................................................... 154 12.13.1 Definition .................................................................................................................................................. 154 12.13.2 Conformance requirement ........................................................................................................................ 154 12.13.3 Test purpose .............................................................................................................................................. 155 12.13.4 Method of test ........................................................................................................................................... 155 12.13.5 Test requirements ...................................................................................................................................... 156 12.14 Void ................................................................................................................................................................ 156 12.15 Void ................................................................................................................................................................ 156 12.16 MO MTSI Text call ........................................................................................................................................ 156 12.16.1 Definition .................................................................................................................................................. 156 12.16.2 Conformance requirement ........................................................................................................................ 156 12.16.3 Test purpose .............................................................................................................................................. 157 12.16.4 Method of test ........................................................................................................................................... 157 12.16.5 Test requirements ...................................................................................................................................... 157 12.17 MT MTSI text call .......................................................................................................................................... 157 12.17.1 Definition .................................................................................................................................................. 157 12.17.2 Conformance requirement ........................................................................................................................ 158 12.17.3 Test purpose .............................................................................................................................................. 158 12.17.4 Method of test ........................................................................................................................................... 158 12.17.5 Test requirements ...................................................................................................................................... 159 12.18 Void ................................................................................................................................................................ 159 12.18a Void ................................................................................................................................................................ 159 12.18b Void ................................................................................................................................................................ 159 12.19 Void ................................................................................................................................................................ 159 12.19a Void ................................................................................................................................................................ 159 12.19b Void ................................................................................................................................................................ 159 12.20 Void ................................................................................................................................................................ 159 12.20a Void ................................................................................................................................................................ 159 12.21 MO MTSI Video call ..................................................................................................................................... 159 12.21.1 Definition .................................................................................................................................................. 159 12.21.2 Conformance requirement ........................................................................................................................ 159 12.21.3 Test purpose .............................................................................................................................................. 163 12.21.4 Method of test ........................................................................................................................................... 163 12.21.5 Test requirements ...................................................................................................................................... 163 12.22 MT MTSI Video call ...................................................................................................................................... 164 12.22.1 Definition .................................................................................................................................................. 164 12.22.2 Conformance requirement ........................................................................................................................ 164

ETSI


12.22.3 Test purpose .............................................................................................................................................. 166 12.22.4 Method of test ........................................................................................................................................... 166 12.22.5 Test requirements ...................................................................................................................................... 166 12.23 MO MTSI speech call / EVS .......................................................................................................................... 166 12.23.1 Definition .................................................................................................................................................. 166 12.23.2 Conformance requirement ........................................................................................................................ 167 12.23.3 Test purpose .............................................................................................................................................. 169 12.23.4 Method of test ........................................................................................................................................... 169 12.23.5 Test requirements ...................................................................................................................................... 169 12.24 MT MTSI speech call / EVS .......................................................................................................................... 170 12.24.1 Definition .................................................................................................................................................. 170 12.24.2 Conformance requirement ........................................................................................................................ 170 12.24.3 Test purpose .............................................................................................................................................. 177 12.24.4 Method of test ........................................................................................................................................... 177 12.24.5 Test requirements ...................................................................................................................................... 177 12.25 MO MTSI speech call / EVS / AMR-WB ...................................................................................................... 177 12.25.1 Definition .................................................................................................................................................. 177 12.25.2 Conformance requirement ........................................................................................................................ 177 12.25.3 Test purpose .............................................................................................................................................. 186 12.25.4 Method of test ........................................................................................................................................... 187 12.25.5 Test requirements ...................................................................................................................................... 189 12.26 MT MTSI speech call / EVS / AMR-WB IO mode ....................................................................................... 189 12.26.1 Definition .................................................................................................................................................. 189 12.26.2 Conformance requirement ........................................................................................................................ 189 12.26.3 Test purpose .............................................................................................................................................. 191 12.26.4 Method of test ........................................................................................................................................... 192 12.26.5 Test requirements ...................................................................................................................................... 193

13 Signalling Compression (SIGComp) .................................................................................................... 193 13.1 SigComp in the Initial registration ................................................................................................................. 193 13.1.1 Definition .................................................................................................................................................. 194 13.1.2 Conformance requirement ........................................................................................................................ 194 13.1.3 Test purpose .............................................................................................................................................. 194 13.1.4 Method of test ........................................................................................................................................... 194 13.1.5 Test requirements ...................................................................................................................................... 197 13.2 SigComp in the MO Call ................................................................................................................................ 198 13.2.1 Definition .................................................................................................................................................. 198 13.2.2 Conformance requirement ........................................................................................................................ 198 13.2.3 Test purpose .............................................................................................................................................. 198 13.2.4 Method of test ........................................................................................................................................... 199 13.2.5 Test requirements ...................................................................................................................................... 202 13.3 SigComp in the MT Call ................................................................................................................................ 203 13.3.1 Definition .................................................................................................................................................. 203 13.3.2 Conformance requirement ........................................................................................................................ 203 13.3.3 Test purpose .............................................................................................................................................. 204 13.3.4 Method of test ........................................................................................................................................... 204 13.3.5 Test requirements ...................................................................................................................................... 208 13.4 Void ................................................................................................................................................................ 209

14 Emergency Service ............................................................................................................................... 209 14.1 Void ................................................................................................................................................................ 209 14.2 Void ................................................................................................................................................................ 209

15 Supplementary Services ....................................................................................................................... 209 15.1 Originating Identification Presentation .......................................................................................................... 209 15.1.1 Definition .................................................................................................................................................. 209 15.1.2 Conformance requirement ........................................................................................................................ 209 15.1.3 Test purpose .............................................................................................................................................. 209 15.1.4 Method of test ........................................................................................................................................... 210 15.1.5 Test requirements ...................................................................................................................................... 210 15.2 Originating Identification Restriction ............................................................................................................. 210 15.2.1 Definition .................................................................................................................................................. 210 15.2.2 Conformance requirement ........................................................................................................................ 210

ETSI


15.2.3 Test purpose .............................................................................................................................................. 211 15.2.4 Method of test ........................................................................................................................................... 211 15.2.5 Test requirements ...................................................................................................................................... 211 15.2a Originating Identification Restriction / Signalling ......................................................................................... 212 15.2a.1 Definition .................................................................................................................................................. 212 15.2a.2 Conformance requirement ........................................................................................................................ 212 15.2a.3 Test purpose .............................................................................................................................................. 212 15.2a.4 Method of test ........................................................................................................................................... 212 15.2a.5 Test requirements ...................................................................................................................................... 213 15.3 Terminating Identification Presentation ......................................................................................................... 213 15.3.1 Definition .................................................................................................................................................. 213 15.3.2 Conformance requirement ........................................................................................................................ 213 15.3.3 Test purpose .............................................................................................................................................. 213 15.3.4 Method of test ........................................................................................................................................... 214 15.3.5 Test requirements ...................................................................................................................................... 214 15.4 Terminating Identification Restriction ........................................................................................................... 214 15.4.1 Definition .................................................................................................................................................. 214 15.4.2 Conformance requirement ........................................................................................................................ 214 15.4.3 Test purpose .............................................................................................................................................. 215 15.4.4 Method of test ........................................................................................................................................... 215 15.4.5 Test requirements ...................................................................................................................................... 215 15.4a Terminating Identification Restriction / Signalling ........................................................................................ 216 15.4a.1 Definition .................................................................................................................................................. 216 15.4a.2 Conformance requirement ........................................................................................................................ 216 15.4a.3 Test purpose .............................................................................................................................................. 216 15.4a.4 Method of test ........................................................................................................................................... 216 15.4a.5 Test requirements ...................................................................................................................................... 217 15.5 Communication Forwarding unconditional .................................................................................................... 217 15.5.1 Definition .................................................................................................................................................. 217 15.5.2 Conformance requirement ........................................................................................................................ 217 15.5.3 Test purpose .............................................................................................................................................. 218 15.5.4 Method of test ........................................................................................................................................... 218 15.5.5 Test requirements ...................................................................................................................................... 218 15.6 Void ................................................................................................................................................................ 219 15.7 Communication Forwarding on non Reply: activation................................................................................... 219 15.7.1 Definition .................................................................................................................................................. 219 15.7.2 Conformance requirement ........................................................................................................................ 219 15.7.3 Test purpose .............................................................................................................................................. 219 15.7.4 Method of test ........................................................................................................................................... 220 15.7.5 Test requirements ...................................................................................................................................... 220 15.8 Communication Forwarding on non reply: MO call initiation ....................................................................... 221 15.8.1 Definition .................................................................................................................................................. 221 15.8.2 Conformance requirement ........................................................................................................................ 221 15.8.3 Test purpose .............................................................................................................................................. 222 15.8.4 Method of test ........................................................................................................................................... 222 15.8.5 Test requirements ...................................................................................................................................... 224 15.9 Communication Forwarding on Busy............................................................................................................. 224 15.9.1 Definition .................................................................................................................................................. 224 15.9.2 Conformance requirement ........................................................................................................................ 225 15.9.3 Test purpose .............................................................................................................................................. 225 15.9.4 Method of test ........................................................................................................................................... 225 15.9.5 Test requirements ...................................................................................................................................... 225 15.10 Communication Forwarding on Not logged-in............................................................................................... 226 15.10.1 Definition .................................................................................................................................................. 226 15.10.2 Conformance requirement ........................................................................................................................ 226 15.10.3 Test purpose .............................................................................................................................................. 226 15.10.4 Method of test ........................................................................................................................................... 227 15.10.5 Test requirements ...................................................................................................................................... 227 15.10a Communication Forwarding on Not reachable............................................................................................... 228 15.10a.1 Definition .................................................................................................................................................. 228 15.10a.2 Conformance requirement ........................................................................................................................ 228 15.10a.3 Test purpose .............................................................................................................................................. 228

ETSI


15.10a.4 Method of test ........................................................................................................................................... 228 15.10a.5 Test requirements ...................................................................................................................................... 229 15.11 MO Call Hold without announcement............................................................................................................ 229 15.11.1 Definition .................................................................................................................................................. 229 15.11.2 Conformance requirement ........................................................................................................................ 229 15.11.3 Test purpose .............................................................................................................................................. 230 15.11.4 Method of test ........................................................................................................................................... 231 15.11.5 Test requirements ...................................................................................................................................... 232 15.11a MO Video Call Hold without announcement ................................................................................................. 232 15.11a.1 Definition .................................................................................................................................................. 232 15.11a.2 Conformance requirement ........................................................................................................................ 232 15.11a.3 Test purpose .............................................................................................................................................. 233 15.11a.4 Method of test ........................................................................................................................................... 233 15.11a.5 Test requirements ...................................................................................................................................... 234 15.12 MT Call Hold without announcement ............................................................................................................ 234 15.12.1 Definition .................................................................................................................................................. 234 15.12.2 Conformance requirement ........................................................................................................................ 234 15.12.3 Test purpose .............................................................................................................................................. 235 15.12.4 Method of test ........................................................................................................................................... 235 15.12.5 Test requirements ...................................................................................................................................... 236 15.12a MT Video Call Hold without announcement ................................................................................................. 236 15.12a.1 Definition .................................................................................................................................................. 236 15.12a.2 Conformance requirement ........................................................................................................................ 236 15.12a.3 Test purpose .............................................................................................................................................. 237 15.12a.4 Method of test ........................................................................................................................................... 237 15.12a.5 Test requirements ...................................................................................................................................... 238 15.13 Incoming Communication Barring except for a specific user ........................................................................ 238 15.13.1 Definition .................................................................................................................................................. 238 15.13.2 Conformance requirement ........................................................................................................................ 238 15.13.3 Test purpose .............................................................................................................................................. 238 15.13.4 Method of test ........................................................................................................................................... 239 15.13.5 Test requirements ...................................................................................................................................... 239 15.14 Incoming Communication Barring for anonymous users ............................................................................... 240 15.14.1 Definition .................................................................................................................................................. 240 15.14.2 Conformance requirement ........................................................................................................................ 240 15.14.3 Test purpose .............................................................................................................................................. 241 15.14.4 Method of test ........................................................................................................................................... 241 15.14.5 Test requirements ...................................................................................................................................... 241 15.14a Incoming Communication Barring while roaming ......................................................................................... 242 15.14a.1 Definition .................................................................................................................................................. 242 15.14a.2 Conformance requirement ........................................................................................................................ 242 15.14a.3 Test purpose .............................................................................................................................................. 242 15.14a.4 Method of test ........................................................................................................................................... 242 15.14a.5 Test requirements ...................................................................................................................................... 243 15.14b Outgoing communication Barring while roaming .......................................................................................... 243 15.14b.1 Definition .................................................................................................................................................. 243 15.14b.2 Conformance requirement ........................................................................................................................ 243 15.14b.3 Test purpose .............................................................................................................................................. 244 15.14b.4 Method of test ........................................................................................................................................... 244 15.14b.5 Test requirements ...................................................................................................................................... 244 15.15 Subscription to the MWI event package ......................................................................................................... 245 15.15.1 Definition .................................................................................................................................................. 245 15.15.2 Conformance requirement ........................................................................................................................ 245 15.15.3 Test purpose .............................................................................................................................................. 246 15.15.4 Method of test ........................................................................................................................................... 246 15.15.5 Test requirements ...................................................................................................................................... 248 15.16 Void ................................................................................................................................................................ 248 15.17 Creating and leaving a conference ................................................................................................................. 248 15.17.1 Definition .................................................................................................................................................. 248 15.17.2 Conformance requirement ........................................................................................................................ 249 15.17.3 Test purpose .............................................................................................................................................. 249 15.17.4 Method of test ........................................................................................................................................... 249

ETSI


15.17.5 Test requirements ...................................................................................................................................... 250 15.18 Inviting user to conference by sending a REFER request to the user ............................................................. 250 15.18.1 Definition .................................................................................................................................................. 250 15.18.2 Conformance requirement ........................................................................................................................ 251 15.18.3 Test purpose .............................................................................................................................................. 251 15.18.4 Method of test ........................................................................................................................................... 251 15.18.5 Test requirements ...................................................................................................................................... 253 15.19 Inviting user to conference by sending a REFER request to the conference focus ........................................ 254 15.19.1 Definition .................................................................................................................................................. 254 15.19.2 Conformance requirement ........................................................................................................................ 254 15.19.3 Test purpose .............................................................................................................................................. 254 15.19.4 Method of test ........................................................................................................................................... 254 15.19.5 Test requirements ...................................................................................................................................... 255 15.19a Inviting user to conference by sending a REFER request to the conference focus / Video............................ 255 15.19a.1 Definition .................................................................................................................................................. 255 15.19a.2 Conformance requirement ........................................................................................................................ 255 15.19a.3 Test purpose .............................................................................................................................................. 256 15.19a.4 Method of test ........................................................................................................................................... 256 15.19a.5 Test requirements ...................................................................................................................................... 258 15.20 Void ................................................................................................................................................................ 259 15.21 Joining a conference after being invited to it.................................................................................................. 259 15.21.1 Definition .................................................................................................................................................. 259 15.21.2 Conformance requirement ........................................................................................................................ 259 15.21.3 Test purpose .............................................................................................................................................. 259 15.21.4 Method of test ........................................................................................................................................... 260 15.21.5 Test requirements ...................................................................................................................................... 267 15.21a.5 Test requirements ...................................................................................................................................... 271 15.21b Joining a conference after being invited to it / Video ..................................................................................... 271 15.21b.1 Definition .................................................................................................................................................. 271 15.21b.2 Conformance requirement ........................................................................................................................ 271 15.21b.3 Test purpose .............................................................................................................................................. 272 15.21b.4 Method of test ........................................................................................................................................... 272 15.21b.5 Test requirements ...................................................................................................................................... 281 15.21c.5 Test requirements ...................................................................................................................................... 285 15.22 Void ................................................................................................................................................................ 285 15.23 Void ................................................................................................................................................................ 285 15.24 Void ................................................................................................................................................................ 285 15.25 MO Explicit Communication Transfer – Consultative Call Transfer ............................................................. 285 15.25.1 Definition .................................................................................................................................................. 285 15.25.2 Conformance requirement ........................................................................................................................ 285 15.25.3 Test purpose .............................................................................................................................................. 286 15.25.4 Method of test ........................................................................................................................................... 286 15.25.5 Test requirements ...................................................................................................................................... 290 15.26 Void ................................................................................................................................................................ 290 15.27 Communication Waiting and answering the call ............................................................................................ 290 15.27.1 Definition .................................................................................................................................................. 290 15.27.2 Conformance requirement ........................................................................................................................ 290 15.27.3 Test purpose .............................................................................................................................................. 292 15.27.4 Method of test ........................................................................................................................................... 292 15.27.5 Test requirements ...................................................................................................................................... 293 15.28 Communication Waiting and cancelling the call ............................................................................................ 294 15.28.1 Definition .................................................................................................................................................. 294 15.28.2 Conformance requirement ........................................................................................................................ 294 15.28.3 Test purpose .............................................................................................................................................. 294 15.28.4 Method of test ........................................................................................................................................... 294 15.28.5 Test requirements ...................................................................................................................................... 296 15.29 GBA authentication ........................................................................................................................................ 296 15.29.1 Definition .................................................................................................................................................. 296 15.29.2 Conformance requirement ........................................................................................................................ 296 15.29.3 Test purpose .............................................................................................................................................. 297 15.29.4 Method of test ........................................................................................................................................... 298 15.29.5 Test requirements ...................................................................................................................................... 298

ETSI


16 Codec selecting .................................................................................................................................... 298 16.1 Void ................................................................................................................................................................ 298 16.2 Speech AMR, indicate selective codec modes ............................................................................................... 298 16.2.1 Definition .................................................................................................................................................. 298 16.2.2 Conformance requirement ........................................................................................................................ 298 16.2.3 Test purpose .............................................................................................................................................. 299 16.2.4 Method of test ........................................................................................................................................... 299 16.2.5 Test requirements ...................................................................................................................................... 304 16.3 Speech AMR-WB, indicate all codec modes ................................................................................................. 304 16.3.1 Definition .................................................................................................................................................. 304 16.3.2 Conformance requirement ........................................................................................................................ 304 16.3.3 Test purpose .............................................................................................................................................. 305 16.3.4 Method of test ........................................................................................................................................... 305 16.3.5 Test requirements ...................................................................................................................................... 310 16.4 Speech AMR-WB, indicate selective codec modes ....................................................................................... 310 16.4.1 Definition .................................................................................................................................................. 310 16.4.2 Conformance requirement ........................................................................................................................ 310 16.4.3 Test purpose .............................................................................................................................................. 310 16.4.4 Method of test ........................................................................................................................................... 311 16.4.5 Test requirements ...................................................................................................................................... 314 16.5 to 16.9 Void ............................................................................................................................................................. 314 16.10 Void ................................................................................................................................................................ 314 16.11 Void ................................................................................................................................................................ 314 16.12 Void ................................................................................................................................................................ 314 16.13 Void ................................................................................................................................................................ 314

17 Media use cases .................................................................................................................................... 314 17.1 MO Speech, add video remove video ............................................................................................................. 314 17.1.1 Definition .................................................................................................................................................. 314 17.1.2 Conformance requirement ........................................................................................................................ 314 17.1.3 Test purpose .............................................................................................................................................. 319 17.1.4 Method of test ........................................................................................................................................... 319 17.1.5 Test requirements ...................................................................................................................................... 327 17.2 MT Speech, add video remove video ............................................................................................................. 327 17.2.1 Definition .................................................................................................................................................. 327 17.2.2 Conformance requirement ........................................................................................................................ 327 17.2.3 Test purpose ..............

Documents

TS 134 229-1 - V14.0.0 - Universal Mobile ... · This Technical Specification (TS) has been produced by ETSI 3rd Generation Partnership Project (3GPP). The present document may refer