Upload
ledom
View
218
Download
0
Embed Size (px)
Citation preview
7/22/2019 Turbo Timer R907
1/3
Turbo Timer (R907)
Please pay attention to vehicle type!
----------------------------AT vehicle produced since 1963
If we cant pull out key when gearshift is in P position and engine is
still running, we have to release safety circuit. refer to P8 for
method of release
-------------------------------------------------------------
For TOYOTA diesel engine, relay of main unit is powered when
turbo timer works and ignition key is at OFF position. Battery motor
of MR-2 electronic vehicle1.10~Highace (1.8~) and etc. runs
continuously sometimes. Please refer to P8 for processing details if
you want to use special adaptorLEVOC seriesbuy separately.
------------------------------------------Battery motor runs when ignition key is at ACC position sometimes.
For vehicle without electronic fan, blue wire of turbo timer has to be
connected to make battery motor runsBut ACC cant be used
when turbo timer works. If vehicle (like NISSAN, ISUZU and
SUBARU) has anti-fault operation relayLEVOCLVH-01/buy
separatelyACC can be used even turbo timer is working.
1
WARRANTYThis product enjoys quality warranty in following condition:
1 Repair free of costin warrantyIn normal use, any failure caused by production in one yearafter purchase is covered by warranty.
2 Repair against following problem is not free even in warrantyperiod.
a) Failure or damage caused by improper use, repair oralteration.
b) Failure or damage caused by incorrect connection.c) Failure or damage caused by water, earthquake, accidence
or fire.
d) Warranty card is not filled out with necessary information(dealer, purchase date, customer name) or information has
been altered.
e) Can not present warranty card.f) Open for cleaning.
11
2
Wiring method depends on vehicle type. If timer doesnt work after
installed according Wiring of specified vehicle or your vehicle type is
not specified there, please connect according to Wiring method 3.
Connect according to power detection
6
Installation & Operation ManualThanks for purchasing Turbo Timer-R907! Please read this
manual carefully to ensure a proper use.
NISSAN
TOYOTA
Battery motor operation
Operation and parts name
Parts name
Time select ion
Switch between 1min and 3min
Digital display
Flash when timer works
L.E.D power indicator
When connect, it is for test
When use, it is for indication
Triple-pole plug
Power ON/OFF
Accessory Clap connector
3pcs Double side adhesive
1pc
Operation SettingOperation
1.Start engine
2.Power ON
L.E.D indicator flash
ONNormally be ON
OFFBe OFF when need to shut down timer and
clear its work
3.Set time by Time
Selection
1minNormal situation
3minAfter long driving
4.Ignition OFFTurbo timer is linked with ignition switch. It
starts work. If dont pull handbrake at thismoment, it stops working, engine stops running
too. (handbrake detects loop)
5. Timer runsIf digital remains ON in display, that
shows timer is running.
Engine will be off after turbo timer runs
for programmed time
6.Engine off
Wiring Diagram
Wiring 3
Standard connection
A IG and ACCconnection
SUZUKI, SUBARU
MITSUBISHI, ISUZU
DAIHATSU, NISSAN Key cylinder
STbattery start circuitACCacc circuitIGignition circuitBbattery+12V
RedYellow
Blue
Black Bolt in vehicle(grounded).Please abrase offink on connectsurface if usecoated bolt
Grey
Hand brake detection
ACC has electronic fan
B IG connection ofsystem 2,ACCis not connected
TOYOTA, SUZUKI,
DAIHATSU, HONDA
MITSUBISHI, MAZDAKey cylinder
STbattery start circuitACCACC circuitIG1ignition electronic fanIG2ignition systemBbattery+12V
RedYellow
Blue
BlackBolt in vehicle(grounded).Please abrase offink on connectsurface if usecoated bolt
GreyHand brake detection
2systems, one for ignition, another for electronic fan
BlackGrounded (Refer P3)
RedPower & storage circuit when key turns to OFF
BlueAccessories power supplying when key turns to ACC
YellowMotor power supplying when key turns to ON
GreyHand brake detectionRefer P4
www.elfinx.com FOR 12V VEHICLE ONLY
7/22/2019 Turbo Timer R907
2/3
Power Switch triple plug
OFF/ON
Turn power off before doing any wiring operation
Connect three wires of triple plug inas following steps:
1 Use special adaptor for different vehicle type LEVOCseriesSimply plug into connector.
2 Refer to Wiring of different vehicle type indicated in thismanual for connection.
3 Check wiring by embedded detector, then connect accordingly.
Connect black wire infor grounding to bolt at installation part.
Grounded through bolt doesnt work well sometimes.
Please abrase off ink on the connecting surface if use coated bolt.
Black wire
Take off skin at the end of wire, round and fix. 3
Connect black wire of Turbo Timer to vehicle body for grounding.
Connect blue wire of Turbo Timer to connector ends to detect correct
connection end, switch between OFF-ACC-ON at the mean time.
When have power supply, LED power indicator will be ON.
Switch key to ON position and LED indicator is ON, if there are 2
more ends can turn on LED indicator except&, or key cylinderdoesnt have ACC position, please connect yellow and blue wire as
following steps:
Switch key to ST position, indicator is ON when connect to yellow
wire, is OFF when connect to blue wire.
Ex.Normal when there are 2ends
BlackGrounding (Connector) GreyHand brake switch
If yellow and blue wire is connected reversely, Turbo Timer will
operate when switch key to ST position.
If still have 2ends can turn on LED indicator when switch key to ST
position, connect these 2ends in any way, it wont be problem.
Refer to following information for connection if vehicle has
keycylinderindication.
RedBAMAM1AM2
BlueACC
YellowIG
Black is for grounding.
If IG have IG1& IG2 two endsconnect yellow and blue with
IG1 & IG2 separately.
7
BlueACC
ACC
YellowON
RedOFF
YellowON-ST
BlueON
RedOFF
Connect grey wire with hand brake switch. wrap
connection end with plastic tape for insulation
Connect according to above picture
Turn key to ON position and test If handbrake switch wire carries 12V when release and 0V when
pull up handbrake, connect this wire to detection grey wire.
Footbrake or gear detection, please operate same as above.
Wiring of specified vehicle with adaptor
Prepare adaptor for specified vehicle typeLEVOC series
4
After installed, LED Power indicator will be ON when switchkey to ACC or ON position, no matter turbo timer itself isswitched ON or OFF.
--------------------------- AT vehicle produced since 1963
Turn off and pull out key, take off connector (blue/red and blue)
extended from key lock spiratron.
Way to release safety circuit
ATTN: Gear shift of some types of vehicle is locked, you need torelease gear shift locking of Nissan AT vehicle by lock releaseconnector (LEVOCLVH-25/buy separately
Before
After
8
Wiring Diagram Wiring Diagram
RedBattery+12V
YellowIgnition circuit
BlueAcc circuit
both detection and test
BlackGrounded
GreyHand brake detection circuit
Picture Key cylinder Find connector extended from key
cylinder, position a and b on picture at left.
Identify vehicle type and connectoraccording Wiring of different vehicle
type.
Wiring Diagram Wiring Diagram
Hand brake switchHand brake detection
thin grey wire
If there are more than 2 hand brake wires
Relative installation picture
Key cylinder ConnectorAdaptor for different vehicle
Connector
3P coupling
oint
Hand brake switch
Key cylinder
BlueBlack
Connector
Connect to triple plug
Grounding
L.E.D Power indicator
Connection
NISSAN
Key cylinder
Key lock spiratronTake off connector
Blue/Red
Blue
TOYOTA
AlterationKey cylinder Connector
Clap Connector
Wiring 1
7/22/2019 Turbo Timer R907
3/3
Wiring of different vehicle type
Basic connection
5
Neednt to take off wire skin
Connect with clap connector.
For safety please disconnect battery cathode before installation.
1 Take off wire skin 3cm length at the end of Turbo Timer wire.2 Take off wire skin 2cm length at the end of vehicle wire.3 Twist two ends together as above diagram.4 Wrap the connection point tightly for insulation.
9
Warranty CardThanks for purchasing Turbo Timer R-907!
This product has passed our factory OQC inspection. If
you meet any problem during normal use, please present this
filled card to dealer or repair center for free repair according
warranty condition listed out.
Product Name Turbo Timer Model# R-907
Customer
TEL
Address:
Name:
Vehicle Type
Purchase Date: year month date
Warranty Period: One year from purchase date
Dealer
Address:
Dealer/Shop Name: www.elfinx.com
12
Double side adhesive
Turbo Timer
Tear off paper on backside of adhesiveInstall Turbo Timer near to
control panel
Confirm wiring method first, then installation place.
Clean surface for affixing, adhesive tape cant be re-used.
To ensure capability of components inside, please dont expose
turbo timer in sunlight.
Vehicle can not run if turbo timer starts work, steering wheel will be
locked when key is pulled out.
Vehicle is in standby situation when turbo timer works.
Ensure there is no flammable article around before use.
Dont use in a close or unventilated garage and similar place.
We dont have duty on any dissension caused by improper use.
If vehicle carries electric fan, please check carefully whether it
works after installation.
10
Wiring Diagram
Female connector
Male connector
Pay attention to connector shape!
Connect to special adaptor properly
according following key cylinder
connector picture
Adaptor bought seperately
3P Connector
Connect special adaptor to triple
connector
Wirin 2
Cut off triple plug, connect ABC wirewith relative wire of connector.
Female connector
Male connector
Key cylinder
STBattery start circuitACCACC circuit
IGIgnition circuitBBattery+12V
Hand brake switch
Red
Yellow
Blue
BlackGrounded wire
Connection
Usage of clap connector
Connector
Wire near to connector
(insert from left side)Wire extended
from amplifier
1. Insert wire into wire slot.
2.Press and clamp
connector by plier 3. Cover and lock, thenfinish connection
Other method When clap connector cant be used
Clap connector can not be used if
vehicle wire is too thick. In this case,please connect according to diagram
on right side.
Vehicle wireWire extended from Turbo Timer
Installation
Attention
Turbo Timer R-907