Tutorial VoIP - CISCO Packet Tracer

Embed Size (px)

Citation preview

Tutorial VoIP - CISCO Packet Tracercomandos en el router------------------Router#enableRouter#conf termEnter configuration commands, one per line. End with CNTL/Z.Router(config)#interface faste0/0Router(config-if)#ip address 192.168.10.1 255.255.255.0Router(config-if)#no shutdownRouter(config-if)#%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to upRouter(config-if)#exitRouter(config)#exitRouter#%SYS-5-CONFIG_I: Configured from console by consoleRouter#wrBuilding configuration...[OK]Router#conf termEnter configuration commands, one per line. End with CNTL/Z.Router(config)#ip DHCP pool VOICERouter(dhcp-config)#network 192.168.10.0 255.255.255.0Router(dhcp-config)#defaul-router 192.168.10.1 ^% Invalid input detected at '^' marker.Router(dhcp-config)#default-router 192.168.10.1Router(dhcp-config)#option 150 ip 192.168.10.1Router(dhcp-config)#exitRouter(config)#exitRouter#%SYS-5-CONFIG_I: Configured from console by consoleRouter#wrBuilding configuration...[OK]Router#conf termEnter configuration commands, one per line. End with CNTL/Z.Router(config)#telepony -service ^% Invalid input detected at '^' marker.Router(config)#telephony -service ^% Invalid input detected at '^' marker.Router(config)#telephony -service ^% Invalid input detected at '^' marker.Router(config)#telephony-serviceRouter(config-telephony)#max-dn 5Router(config-telephony)#max-ephones 5Router(config-telephony)#ip source-address 192.168.10.1 port 2000Router(config-telephony)#auto asign 4 to 6 ^% Invalid input detected at '^' marker.Router(config-telephony)#auto assign 4 to 6Router(config-telephony)#auto assign 1 to 5Router(config-telephony)#exitRouter(config)#exitRouter#%SYS-5-CONFIG_I: Configured from console by consoleRouter#wrBuilding configuration...[OK]Router#conf termEnter configuration commands, one per line. End with CNTL/Z.Router(config)#ephone-dn 1Router(config-ephone-dn)#%LINK-3-UPDOWN: Interface ephone_dsp DN 1.1, changed state to upRouter(config-ephone-dn)#number 54001Router(config-ephone-dn)#%IPPHONE-6-REGISTER: ephone-1 IP:192.168.10.2 Socket:2 DeviceType:Phone has registered.Router(config-ephone-dn)#exitRouter(config)#ephone-dn 2Router(config-ephone-dn)#%LINK-3-UPDOWN: Interface ephone_dsp DN 2.1, changed state to upRouter(config-ephone-dn)#number 54002Router(config-ephone-dn)#exitRouter(config)#exitRouter#%SYS-5-CONFIG_I: Configured from console by consoleRouter#wrBuilding configuration...[OK]Router#conf termEnter configuration commands, one per line. End with CNTL/Z.Router(config)#ip%IPPHONE-6-REGISTER: ephone-2 IP:192.168.10.3 Socket:2 DeviceType:Phone has registeredRouter(config)#ephone-dn 3Router(config-ephone-dn)#%LINK-3-UPDOWN: Interface ephone_dsp DN 3.1, changed state to upRouter(config-ephone-dn)#number 54003Router(config-ephone-dn)#exitRouter(config)#exitRouter#%SYS-5-CONFIG_I: Configured from console by consoleRouter#wrBuilding configuration...[OK]Router#%IPPHONE-6-REGISTER: ephone-3 IP:192.168.10.4 Socket:2 DeviceType:Phone has registered.comandos en el switchSwitch>enabSwitch#conf termEnter configuration commands, one per line. End with CNTL/Z.Switch(config)#interface range fastethernet0/1-6Switch(config-if-range)#switchport mode accesSwitch(config-if-range)#switchport voice vlan 1Switch(config-if-range)#exitSwitch(config)#exitSwitch#%SYS-5-CONFIG_I: Configured from console by consoleSwitch#wrBuilding configuration...[OK]Switch#%LINK-5-CHANGED: Interface FastEthernet0/3, changed state to up%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/3, changed state to up%LINK-5-CHANGED: Interface FastEthernet0/4, changed state to up%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/4, changed state to upSwitch con0 is now availablePress RETURN to get started.