Embed Size (px)
Citation preview
Acryline Ultimate IIMassaging System BathBlower Relocation Kit
w w w . a c r y l i n e s y s t e m b a t h s . c o m
www.acrylinesystembaths.com
Thank you for choosing Acryline’s Ultimate II Massaging System bath.We are confident that you will soon discover what a great decision youmade as you begin enjoying many years of exceptional massage.
This cover note is attached to an Ultimate II Blower Relocation kit and isintended to give your installer a simple overview of how to relocate theblower motors and black box.
Your Ultimate II Massaging System bath was shipped from our factorywith all of the system components mounted and fully tested. It was alsoshipped with an Ultimate II Blower Relocation Kit containing 4 dinconnection extension wires that are each 15 feet in length, two blue flexibleair hoses that are each 15 feet in length with 4 hose connectors attached.Basically, you will be disconnecting 2 blower motors and 1 black box from
where they are factory mounted now and moving them to where you wantthem and then using these parts to reconnect the system. This is easy andall it really requires is that you pay close attention to these directions.
If you need assistance in performing this relocation we ask that you pleasecall our customer service department at one of the two numbers belowdependent upon where you are located in North America.
In Eastern Canada (Ontario province east through Atlantic Canada)call 800-567-0920.In Western Canada (Manitoba west through British Columbia)call 800-794-4667.In the United States call 800-794-4667.
4 / 15’ Din connect extension wires
2 / Flexible air hose extensions with hose connectors
Heat probe
Heat probe
LED Light
LED Light
Exciter boardfor wirelesskeypad
www.acrylinesystembaths.com
April2008
w w w . a c r y l i n e s y s t e m b a t h s . c o m
1
°C °F
2
°C °F2
1
PVC pipe out to health / channel air intake on bath
Ultimate II
X Not used
CONTROL BOX
1
°C °F
2
°C °F2
1
PVC pipe out to aqua / injector air intake on bath
IDENTIFY BLOWER MOTORS AND CONTROL BOX MOUNTEDBELOWTHE BATH UPON RECEPTION
DISCONNECT BOTH BLOWER MOTORS ANDTHE CONTROL BOXAND REMOVETHEM FROMTHE MDF MOUNTING BOARD BELOWTHE BATH
CONTROL BOX
Unscrew PVC pipe from blower / channel air intake on bath
Unscrew PVC pipe from blower / injector air intake on bath
Heat probe
Heat probe
LED Light
LED Light
Exciter boardfor wirelesskeypad
Disconnect all cablesfrom control box
X Not used
Disconnectpowersupplybeforeinstallingrelocation kit
Blower relocation(Wireless keypad)
IMAGE 1
IMAGE 2
Health /ChannelBlower
Aqua /InjectorBlower
Health /ChannelBlower
Aqua /InjectorBlower
#1
#2
#1Channel
#2Injector
#1Channel
#2Injector
(RED INDICATES ELEMENTS TO DISCONNECT)
Heat probe
Heat probe
LED Light
LED Light
Exciter board forwireless keypad
Blower relocation(Wireless keypad)
www.acrylinesystembaths.com
April2008
w w w . a c r y l i n e s y s t e m b a t h s . c o m
1
°C °F
2
°C °F2
1
Connect flexible air hose extensions
Ultimate II
X Not used
CONTROL BOX
Connect flexible air hose extensions
CONNECT RELOCATION KIT COMPONENTS (4 DIN EXTENSIONWIRESAND 2 AIR HOSES) ALL DEVICES MUST BE ON A HORIZONTAL PLAIN
Reconnectpowersupplyonce allotherconnectionsare done
POST POWER UP NOTES
1 Before plugging the black box into the power source and starting the system verify that allcomponents are secured, all connections are color coordinated and extention cables are securelyinserted into the same sockets as demonstrated in image 4.
2 Start system without water to verify that:- power is present- air exits through both systems i.e., channel system button blows air through channeland injection system button blows air through injector.- both chroma therapy lights are functional
3 Failure to follow these instructions could result in serious personal injury and / or property damageand may void the warranty.
4 AcrylineR takes no responsibility for any damage, loss, cost, expense or liability due to failure infollowing these instructions.
IMAGE 3Health /ChannelBlower
Aqua /InjectorBlower
#4
PLACE CONTROL BOX AND BLOWER MOTORS ON FLAT HORIZONTALSURFACE AT CHOSEN RELOCATION AREA (DO NOT PLUG BLACK BOXTO POWER SUPPLY UNTIL ALL CONNECTIONS ARE SECURE)
#3
#5
#1Channel
#2Injector
(GREEN INDICATES ELEMENTS TO RECONNECT)
Heat probe
Heat probe
LED Light
LED Light
Keypad
www.acrylinesystembaths.com
April2008
w w w . a c r y l i n e s y s t e m b a t h s . c o m
1
°C °F
2
°C °F2
1
PVC pipe out to health / channel air intake on bath
Ultimate II
X Not used
CONTROL BOX
1
°C °F
2
°C °F2
1
PVC pipe out to aqua / injector air intake on bath
CONTROL BOX
Unscrew PVC pipe from blower / channel air intake on bath
Unscrew PVC pipe from blower / injector air intake on bath
Heat probe
Heat probe
LED Light
LED Light
Keypad
Disconnect all cablesfrom control box
X Not used
Disconnectpowersupplybeforeinstallingrelocation kit
Blower relocation(Hard-wired keypad)
IMAGE 1
IMAGE 2
Health /ChannelBlower
Aqua /InjectorBlower
Health /ChannelBlower
Aqua /InjectorBlower
#1
#1Channel
#2Injector
#1Channel
#2Injector
(RED INDICATES ELEMENTS TO DISCONNECT)
IDENTIFY BLOWER MOTORS AND CONTROL BOX MOUNTEDBELOWTHE BATH UPON RECEPTION
DISCONNECT BOTH BLOWER MOTORS ANDTHE CONTROL BOXAND REMOVETHEM FROMTHE MDF MOUNTING BOARD BELOWTHE BATH
#2
Heat probe
Heat probe
LED Light
LED Light
Keypad
Blower relocation(Hard-wired keypad)
www.acrylinesystembaths.com
April2008
w w w . a c r y l i n e s y s t e m b a t h s . c o m
1
°C °F
2
°C °F2
1
Connect flexible air hose extensions
Ultimate II
X Not used
CONTROL BOX
Connect flexible air hose extensions
Reconnectpowersupplyonce allotherconnectionsare done
IMAGE 3Health /ChannelBlower
Aqua /InjectorBlower
POST POWER UP NOTES#5
#1Channel
#2Injector
1 Before plugging the black box into the power source and starting the system verify that allcomponents are secured, all connections are color coordinated and extention cables are securelyinserted into the same sockets as demonstrated in image 4.
2 Start system without water to verify that:- power is present- air exits through both systems i.e., channel system button blows air through channeland injection system button blows air through injector.- both chroma therapy lights are functional
3 Failure to follow these instructions could result in serious personal injury and / or property damageand may void the warranty.
4 AcrylineR takes no responsibility for any damage, loss, cost, expense or liability due to failure infollowing these instructions.
CONNECT RELOCATION KIT COMPONENTS (4 DIN EXTENSIONWIRESAND 2 AIR HOSES) ALL DEVICES MUST BE ON A HORIZONTAL PLAIN
#4
PLACE CONTROL BOX AND BLOWER MOTORS ON FLAT HORIZONTALSURFACE AT CHOSEN RELOCATION AREA (DO NOT PLUG BLACK BOXTO POWER SUPPLY UNTIL ALL CONNECTIONS ARE SECURE)
#3
(GREEN INDICATES ELEMENTS TO RECONNECT)
