ULTRAFEED® PLUS & PREMIUM PACKAGE

ASSEMBLY INSTRUCTIONSvideo instructions atSailrite.com/Ultrafeed-Setupor search part #300179XHT

Unpack Industrial Carrying Case1. Use the case handle to pull the case from the

box.

2. Remove the case top by unlatching the butterfly latches (A) on both ends.

3. Remove the sewing machine, tools, thread stand (outside of foam shell), balance wheel and belts from the packaging.

4. Check to make sure the hinge holes (B) on the back of the machine are unobstructed by the set screws (C). If necessary, back the screws out to clear the hole.

5. On the case, tilt the two hinge posts slightly upward.

6. Lift up the sewing machine head and carefully guide the hinge posts into the hinge holes on the back side of the machine head (D).

7. Tip the machine head back and use a stubby screwdriver with medium head (not included) to tighten the set screws (C) on the underside of the machine head.

Ultrafeed® PackagingThe Ultrafeed Sewing Machine head comes in a specially designed box with foam shell packaging which protects it from damage.

Please save all original packaging to use if the machine ever needs to be sent in for service. Carriers will not pay insurance claims on improperly packaged machines even if they are insured.

NOTE: Do not ship a machine in its case. Always use the box and foam shell packaging in which it was originally shipped.

Place Machine Head in Industrial Carrying Case

A

C

B

D

E

F

Install Balance Wheel & Belt 8. Remove the two screws (E) located above and

below the idler pulley. Position the belt cover (F) over the idler pulley and belt. Snug the two screws back in place to secure the belt cover.

9. Free the top of the Timing Belt by pushing the Bobbin Winder Stopper (G) away from the belt. Unscrew the reverse-threaded Posi-Pin® Nut (H). Slide the Power Plus® or Monster® II Balance Wheel onto the Posi-Pin Wheel Bushing (I), making sure the Timing Belt is over the top of the machine (J) and to the left of the balance wheel.

10. Thread the reverse-threaded nut back onto the bushing and tighten by hand. NOTE: In order to properly rotate the balance wheel, place your hand on the top of the balance wheel and pull toward you (K).

11. Check to be sure the Timing Belt is still around the small cogged pulley of the idler pulley (L). Turn the balance wheel while guiding the belt into place around the large wheel (just like a bicycle chain).

12. Push the Posi-Pin (M) through one of the holes in the balance wheel (N) (any will work). While maintaining pressure on the Posi-Pin rotate the balance wheel (K) until the Posi-Pin locks into one of the balance wheel bushing holes (O). Rotation of the balance wheel will now cause the machine to function.

13. To disengage the machine (for bobbin winding), pull the Posi-Pin out of the balance wheel. The balance wheel will now rotate without operating the machine. Push the pin into the hole at the center of the Posi-Pin nut to store (P).

Plug In Ultrafeed®

14. Plug the cord from the foot control (Q) into the SAILRITE embossed end of the Light Adapter (R) and the other end into the socket wired to the motor (S). The plug can only be inserted properly one way. Regular household current should be used (115 volts for 110V power systems or 220-240 volts for 220V power systems, 50/60 Hz).

G

H

J

N

K

P

Q R

S

I

L

O

M

Install Spool Pin 15. Find the felt pad and spool pin (silver threaded rod

about 2 inches long with holes in it) in the tool bag.

16. Use a flat-head screwdriver to screw the spool pin into the top of the machine, then place the red felt disk over the spool pin (T).

Assemble Thread Stand (Optional) NOTE: Ultrafeed PLUS and PREMIUM Sewing Machines also include the Integrated Thread Stand which may be used in place of the standard thread stand. Follow the instructions provided with the Integrated Thread Stand for its setup.

17. Insert the long rod (U) into the outlying hole in the base. Position the hook end up over the base and secure with the set screw (V). Insert the smaller rod (W), a post support for the thread cone, into the center hole with the tapered end facing up and hammer in.

Accessories AssemblyTo attach the Flex20 LED Light, place the magnetic light in your desired location on the machine and plug it into the bottom of the Light Adapter (X). Optional: Attach the included plastic clips to the back of the sewing machine and use the zip ties to hold the cord (Y).

105451*1

Ultrafeed® Plus & Premium Package Assembly Instructions

Qty: 1 Ultrafeed® PATENTED TECHNOLOGY Patents #6499415 • #7438009

Sailrite.comEquipping you to sew

Copyright ©2020

T

V

U

W

YX