FEATURES AND BENEFITS:

CALL FREE: 0808 118 1922 MEONUK.COM

Spectrum UltraLine is a methyl-methacrylate (MMA) cold plastic for line markings. UltraLine consistently outperforms

traditional thermoplastic as it is extremely hardwearing and has excellent adhesion to asphalt and concrete surfaces; this

includes monoblocks and pavers. Can be applied by hand or using specialist application equipment for larger applications.

• Very hard wearing - lasts at least 3 times as long as thermoplastic

• Excellent adhesion to concrete and cemetitious surfaces

• BSI approved for highway use

• Very fast cure time to allow rapid re-opening of areas to traffic

• White is retro-reflective; all colours can have reflective beads added

• Solvent-free formula

PRT-032-V2

Traffic RedRAL 3020

Mint GreenRAL 6029

Traffic BlueRAL 5017

Traffic YellowRAL 1023

Deep CreamBS381:353

Many morecolours available

UltraLine - MMA LINEMARKING PAINT

Technical Data Sheet: UltraLine Page 2

MEON UK

TEL: EMAIL:WEB:

+44 (0)808 118 1922mail@meonuk.com meonuk.com

MEON IRELAND

TEL: EMAIL:WEB:

+353 (0)1 840 7647info@meonireland.commeon.ie

Touch dry: 5 minutes @ 15⁰CWalk on time: 15 minutes @ 15⁰CTraffic time: 60 minutes @ 15⁰C

Use Meon UltraClean X795 to clean uncured UltraLine from tools and equipment. Lines can be maintained by cleaning with clean water or mild detergent solution.

Avoid inhalation of vapours and contact with skin and eyes. Wear

suitable protective clothing, gloves and eye/face protection.

Familiarise yourself with the material safety data sheets before

using this product. If you need a copy please call our technical team

on 023 9220 0606.

STORAGE CONDITIONS: Storage area should be dry, protected from direct sunlight and extremes of temperature - i.e. between 5 & 20⁰C. If product is stored for more than 30 days, full and thorough mechanical mixing will be required before using.

SHELF LIFE: 12 months when stored under cover, in original unopened containers, in accordance with Storage Condition guidelines listed above.

SIZES AVAILABLE:Supplied in 8kg tins.

COVERAGE:Area: 0.4m² per kgLinear: 4m of 100mm line per kgWFT: 1000 microns

CERTIFICATION: (manufactured to BS:EN1426)

Test Class

Luminance B0

Colour (x) white

Colour (y) white

RL Dry (mcd/m²/lx) R4

RL Wet (mcd/m²/lx) RW0

Skid Resistance S2

Qd (mcd/m²/lx) Q3

CURING:

AFTERCARE AND MAINTAINENCE:

HEALTH AND SAFETY:

STORAGE:

PREPARATION:

MIXING:

APPLICATION:

TECHNICAL:

SURFACE PREPARATION:The application surface should be dry, sound and clean, free from grease, oil, rust, scale, dirt, or any other soiling or moisture that might affect adhesion or performance. In any case, but especially in the case of overcoating existing line markings, it is further recommended that test areas be coated to ensure good adhesion and/or compatibility with the substrate. Asphalt - weathered - It is recommended that asphalt and other similar surfaces be allowed to thoroughly harden for up to 2 months before painting. Test trials should be carried out in the first instance on a small area.Asphalt - new - whilst we do not recommend coating new surfaces, we appreciate that it often has to happen. There is a risk of bitumen “bleed” through the line; if this happens we recommend either priming the area with Meon UltraNuvo asphalt primer, Meon ViaLine F210, or laying a thin coating of UltraLine, allowing to cure and then laying a 2nd full coat on top, as the bleed is usually contained within the first coat. Concrete and other cementitious surfaces, including powerfloat, tamped or brushed concrete, monoblocks and pavers – we recommend a preparation method suitable for the specific location and surface is carried out before application of product, to ensure surface is properly prepared back to clean and sound substrate. It is critical that utmost attention is paid to cleanliness and good workmanship, whatever preparation method is used, as the presence of any loose material, dust, soiling or previous coatings are likely to reduce adhesion of new coatings. New concrete should be left to harden before coating, as the curing process and residual moisture content can lead to product delamination if coated too early.

PRIMERS:We always recommend priming concrete with Meon UniPrime X250 primer, to reduce porosity and improve adhesion. However, whilst tests have proved that priming gives the best curing leading to a superior bond, there have been many metres of UltraLine laid successfully on brushed or tamped concrete, where the roughness of the surface provides good “grip” for the UltraLine.

MIXING INSTRUCTIONS:It is essential that UltraLine is properly mixed using mixing paddle and drill, or similar. The resin component should be stirred thor-oughly, then mix the catalyst component into the base component, for minimum of 90 seconds. If the product is not properly mixed it is likely that the chemical reaction will be impeded and the product may not perform properly.

THINNING: This product must not be thinned.

We recommend the use of hand moulds to extrude the product. Rollers can be also be used for larger areas such as zebra crossings and stop lines. Alternatively, special application equipment can be used to machine apply - contact Meon for more information If retro-reflectivity is required, broadcast reflective beads or bead/grain mix onto lines immediately after laying and before curing commences.