Using Cmd nokia.pdf

[USING CMD NOKIA] August 22, 2013

Phoeung Rim BSS Team Leader Page 1

COMMAND CHECK LIST IN HW/NOKIA I. Whole Nokia command

Step ZEEI: OpenLog [Location of file *.log] Connect [BSC_Name] Command type; Disconnect CloseLog Stop

II. Nokia 2G 1. ZEEI: Use this command to check site/Cell status and parameter.

- BCF ...... BCF IDENTIFICATION ( &,&& ) - SEG ...... SEG IDENTIFICATION ( &,&& ) - SEGNAME .. SEG NAME ( & ) - BTS ...... BTS IDENTIFICATION ( &,&& ) - NAME ..... BTS NAME ( & )

Syntax - ZEEI:BCF= [BCF_ID]; - ZEEI:NAME=[Cell_name]; - ZEEI:SEG=[Cell_ID]; - ZEEI:BTS=[Cell_ID]; - ZEEI:SEGNAME=[Cell_name];

Ex: ZEEI:BCF=1; ZEEI:BTS=3;

NOKIA Alarm ID: Site down : 7704 AC On DC: 7401 DC Low: 7405,7602 BCCH Missing: 7767



2. ZEOL: Use this command to check site/cell current alarm. Syntax:

ZEOL:[BCF_ID]; ZEOL:BCF_ID:NR=[Alarm_ID];

EX: ZEOL:1; ZEOL:1:NR=7402; (check only alarm External 2)

3. ZEOH: Use to check history alarm. Syntax:

ZEOH:[yyyy-mm-dd,hh-mn-ss]:NR=[Alarm_ID],BCF=[BCF_ID]; ZEOH::BCF=[BCF_ID],NR=[Alarm_ID];

EX: ZEOH:2013-08-22,00-00-00:BCF=1,NR=7401; ZEOH::1,NR=7401;



4. ZEQS: Use this command to Lock/Unlock cell Syntax:

ZEQS:NAME=[Cell_name]:L:FHO,[second to force handover]; ZEQS:NAME=[Cell_name]:U;

Ex: ZEQS:NAME=SIE0011:L:FHO,40;

After Lock:

Ex: ZEQS:NAME=SIE0011:U;



5. ZEFS: Use this command for Lock/Unlock BCF [Abnormal command] Syntax:

ZEFS:[BCF_ID]:L/U; Ex: ZEFS:4:L; ZEFS:4:U;

6. ZEFR: Use this command for Reset site. [Abnormal command] Syntax: ZEFR:[BCF_ID]:SITE; Ex: ZEFR:1:SITE; In this case command will ask you Are you sure you want to reset site? and then type letter Y for Reset and N for un-reset. [CONFIRM COMMAND EXECUTION: Y/N ? Y]

7. ZYEF: Use this command for check E1 status. Syntax:

ZYEF:ET,[ET/PCM_Number]; Note: Before use this command please use command ZEEI for display ET/PCM number.



Ex: ZYEF:ET,514; Note: If you see as picture beloved PCM OK it means E1 of site working normal.

But if you see as picture beloved PCM FAILURE OBSERVED BY FAMILIES 1E7 it means E1 of site down.

8. ZYMO: Use this command for check % of E1 (Local End/Remote End) Syntax:

ZYMO:ET,[ET/PCM_Num]; Ex: ZYMO:ET,514;



Note: If Local End and Remote End less than 100% it means E1 not good need to fix again.

9. ZEQE: Use this command to modify transceiver mode (BB,RF, N) PARAMETER NAMES:

- BTS .... BASE TRANSCEIVER STATION - NAME ... BASE TRANSCEIVER STATION NAME - SEG .... SEGMENT IDENTIFICATION - SEGNAME. SEGMENT NAME

Syntax: ZEQE:NAME=[Cell_Name]:HOP=[ BTS FREQUENCY HOPPING FUNCTION MODE]

BTS FREQUENCY HOPPING FUNCTION MODE - BB ... BASEBAND HOPPING IS USED - RF ... RADIO FREQUENCY HOPPING IS USED - N ... FREQUENCY HOPPING IS NOT USED */

Note: Before you this command we need to Lock cell ZEQS. And then Unlock. Ex: ZEQE:NAME=SIE0011:HOP=N; ZEQE:NAME=SIE0011:HOP=BB;



10. ZEQO: Use this command to display BTS parameter. Syntax:

ZEQO:NAME=[Cell_Name]; Ex: ZEQO:NAME=SIE0011;

11. ZEQV: Use this command to enable/disable GPRS or EGDE PARAMETER NAMES:

- BTS .... BASE TRANSCEIVER STATION - NAME ... BASE TRANSCEIVER STATION NAME - SEG .... SEGMENT IDENTIFICATION - SEGNAME. SEGMENT NAME

IDENTIFY GPRS PARAMETERS: - GENA ........ GPRS ENABLED - EGENA ....... EGPRS ENABLED - RAC ......... ROUTING AREA CODE - CDED ........ DEDICATED GPRS CAPACITY - CDEF ........ DEFAULT GPRS CAPACITY - CMAX ........ MAX GPRS CAPACITY - BFG ......... PREFER BCCH FREQUENCY GPRS - DLA ......... DL ADAPTION PROBABILITY THRESHOLD - ULA ......... UL ADAPTION PROBABILITY THRESHOLD - DLB ......... DL BLER CROSSPOINT FOR CS SELECTION NO HOP - ULB ......... UL BLER CROSSPOINT FOR CS SELECTION NO HOP - DLBH ........ DL BLER CROSSPOINT FOR CS SELECTION HOP - ULBH ........ UL BLER CROSSPOINT FOR CS SELECTION HOP - COD ......... CODING SCHEME NO HOP - CODH ........ CODING SCHEME HOP



- MCA ......... INITIAL MCS FOR ACKNOWLEDGED MODE - MCU ......... INITIAL MCS FOR UNACKNOWLEDGED MODE - BLA ......... MAXIMUM BLER IN ACKNOWLEDGED MODE - BLU ......... MAXIMUM BLER IN UNACKNOWLEDGED MODE - MBG ......... MEAN BEP OFFSET GMSK - MBP ......... MEAN BEP OFFSET 8PSK - ELA ......... EGPRS LINK ADAPTATION ENABLED - CS34 ........ CODING SCHEMES CS3 AND CS4 ENABLED - DCSA ........ DL CODING SCHEME IN ACKNOWLEDGED MODE - UCSA ........ UL CODING SCHEME IN ACKNOWLEDGED MODE - DCSU ........ DL CODING SCHEME IN UNACKNOWLEDGED MODE - UCSU ........ UL CODING SCHEME IN UNACKNOWLEDGED MODE - ALA ......... ADAPTIVE LA ALGORITHM

Syntax: ZEQV:NAME=[Cell_name]:[ IDENTIFY GPRS PARAMETERS]:[ GIVE FUNCTION MODE[Y/N]; Ex: EQV:NAME=SIE0011:EGENA=Y,GENA=Y;

Note: Before use this command please lock cell [ZQES].



12. ZDTI: Use this command for identify name(s) or number(s) of d-channel link set (LAPD) IDENTIFY ADDITIONAL FILTERING OPTION: SAPI AND PCM-NUMBER(S)

- SAPI ... SERVICE ACCESS POINT IDENTIFIER - PCM ... EXTERNAL PCM NUMBER(S)

Syntax: ZDTI:::PCM=[Cell_name];

Ex: ZDTI:::PCM=514;

13. ZDTC: Use this command for Enable/ Disable LAPD Link to access D-Channel between BTS and BSC IDENTIFY D-CHANNEL STATE CHANGE:

- WO ... EXECUTE - BL ... BLOCK - AL ... ALLOW ACTIVATION - AD ... DENY ACTIVATION

Syntax: ZDTC:[LAPD_Name]:[ D-CHANNEL STATE CHANGE];

Ex: ZDTC:TR11:WO; 1. WORKING STATE

2. BLOCKING STATE ZDTC:TR11:BL;



14. ZEFO: Use this command display external alarm port. IDENTIFY PARAMETER GROUP :

- IDE = BCF IDENTIFICATION PARAMETERS - HOP = FREQUENCY HOPPING PARAMETERS - IOP = EXTERNAL INPUTS AND OUTPUTS OF BCF - ALL = ALL PARAMETERS

Syntax: ZEFO:[BCF_ID]:[IDENTIFY PARAMETER GROUP];

Ex: ZEFO:1:IOP;



15. ZEFX: Use this command open external alarm port. PARAMETER NAMES:

- ROU .... ROUTE ACTIVATE THE ROUTING OF THE INPUT ALARM AND SET THE REPORTING ROUTE

o NOT .... NOT ACTIVATED (NOT REPORTED) o ACT .... ACTIVATED, REPORTED TO BSC AS A NORMAL EXTERNAL ALARM o TMS .... ACTIVATED, REPORTED AS A TRANSMISSION ALARM TO THE

` TRANSMISSION MANAGEMENT SYSTEM o MAINS .. ACTIVATED, REPORTED TO BSC AS A MAINS BREAKDOWN ALARM

- POL .... POLARITY POLARITY OF EXTERNAL INPUT CONNECTION

o OPEN ..... ACTIVE WHEN OPEN o CLOSED ... ACTIVE WHEN CLOSED

Syntax: ZEFX:[BCF_ID]:INBR[EXT_INPUT_NUM]:[ PARAMETER NAMES]=[ACTIVE ROUT OR POLARITY],:TDI=[ EXT_INPUT_NUM]:SEV=[Alarm_Level];

Ex: ZEFX:1:INBR=1:POL=OPEN,ROU=ACT,:TID=1,SEV=AL3;

16. ZEFE: Use this command for create External alarm name. Syntax:

ZEFE:TID=[Ext_Num]:TEXT=[Ext_Alr_Name]; Ex: ZEFE:TID=1:TEXT="AC ON DC CAB FAILURE";



17. ZEOR: Use this command for cancel general alarm. Syntax:

ZEOR:[BCF_ID]:[Alarm_ID]; Ex: ZEOR:1001: 45920;

III. Nokia 3G

1. Login to Application launcher a. RCMT04 IP: 10.79.3.4 user: Nemuadmin, Password: nemuuser b. RCMT05 IP: 10.79.3.68 user: Nemuadmin, Password: nemuuser c. RCMT06 IP: 10.79.3.132 user: Nemuadmin, Password: nemuuser

2. Login to Tang:

a. RCMT04 user: BSSNOC, Password: 123456 b. RCMT05 user: BSSNOC, Password: 123456 c. RCMT06 user: BSSNOC, Password: 123456

3. ZAAP: Use this command for display current alarm of NodeB. Syntax:

ZAAP:WBTS,[NodeB_ID]; Ex: ZAAP:WBTS,301;



4. ZAHP: Use this command to check history alarm. OUTPUT FORMAT

L ... LONG OUTPUT FORMAT S ... SHORT OUTPUT FORMAT

Syntax: ZAHP:WBTS,[NodeB_ID],::[YYYY-MM-DD,HH-MM-SS],:[OUTPUT FORMAT];

Ex: ZAHP:WBTS,301,::2013-08-20,00-00-00,:L;

The End

Documents

Using Cmd nokia.pdf