Using NoN-Samsung USB WiFi Dongles With TV - SamyGO

Using NoN-Samsung USB WiFi dongles with TV

From SamyGO

It's possible to you your WiFi dongle with Samsung TV's.

Samsung WiFi Dongles uses RaLink rt73, rt2570sta, rt2870sta chips. But their drivers in the TV doesn't include otherbrands ID's, thats why you cannot use other RaLink chipped USB dongles. Because TV thinks they are incompatible. Soyou can unload older drivers and install native drivers that we pre-compiled for you. Then your TV works with any WiFiUSB dongle that uses RaLink chip compatible with rt73, rt2500, rt2870...

Now we have another alternative way (hardware way) that you don't needed to change anything on your TV!

Contents

1 Hardware Way1.1 Compiling Custom Kernel Modules that supports e2p for Hardware Hack1.2 Written wrong values? Fix driver.

2 Software Way2.1 Instructions

2.1.1 Basic Way2.1.2 Advanced Way

2.2 Debugging2.3 USB WiFi dongles that uses RaLink chip/driver

2.3.1 Dongles that tested on forum2.3.2 Dongles that we insist working on this TV

3 Forum Page

Hardware WayThis is preferred way because it's compatible with B and C series.

Samsung TV's kernel module has just Samsung VID/PID values. Because of this, even if your hardware has supportedchip (like rt2870sta) does not work on Samsung TVs because driver cannot recognize that PID and VID values and can'tchoose driver for that device. So there is two way to make your WiFi dongle works on TV.

Changing your dongles PID/VID value (this requires your dongle has already supported chipset in it) orInstalling new drivers (kernel module) for your WiFi dongles (this requires to install some programs to TV, which ismore complicated).

This hardware hack works via changing USB WiFi dongles Vendor and Product Identifier Numbers. Overriding originalvalues to Samsung Vendor Identifier Number (0x04E8) and Samsung WIS09ABGN dongle product Identifier Number(0x2018) makes dongle recognized by TV.

All you need is a dirt cheap USB WiFi dongle that has compatible chipset (rt) and allows eeprom PID/VID changing. Thanyou could disguise your dongle as original Samsung dongle camouflage with some commands at linux.

Those dongles will make same job as price premium Samsung's original dongles!

Probably working modules still available at internet. All you need is rt2870 chipped USB WiFi dongle.

I located this one at Amazon (http://www.amazon.com/Intellinet-523974-Wireless-300N-Adapter/dp/B001DYK87C).

Using NoN-Samsung USB WiFi dongles with TV - SamyGO http://wiki.samygo.tv/index.php5/Using_NoN-Samsung_USB_WiFi_...

1 of 8 08/04/2014 21:52

And this one at ebay (http://www.ebay.com/itm/Ralink-JR300N-USB-Adapter-replace-Samsung-WIS09ABGN-/261180510093?pt=US_USB_Wi_Fi_Adapters_Dongles&hash=item3ccf924f8d).

Tested dongle models are:

It's reported that Edimax EW-7718Un has rt2870 chip.

Dlink DWA-125 UK (http://shop.ebay.co.uk/i.html?_nkw=dwa125&_frs=1) - USA (http://shop.ebay.com/i.html?_nkw=dwa125&_frs=1) - AU (http://shop.ebay.com.au/i.html?_nkw=dwa125&_frs=1)

!!!DWA-125 lots of errors reported please check forum!!!

Dlink DWA-140 UK (http://shop.ebay.co.uk/i.html?_nkw=dwa140&_frs=1) - USA (http://shop.ebay.com/i.html?_nkw=dwa140&_frs=1) - AU (http://shop.ebay.com.au/i.html?_nkw=dwa140&_frs=1) (Notice: It'sconfirmed that HW Rev B1 recognized by C series without change. Also problem reported with HW Rev B2, lookslike stick does not flash eeprom values properly.)

!!!Rev B2 flashes ok however wrong chipset will not work!!!

Dlink DWA-160 UK (http://shop.ebay.co.uk/i.html?_nkw=dwa160&_frs=1) - USA (http://shop.ebay.com/i.html?_nkw=dwa160&_frs=1) - AU (http://shop.ebay.com.au/i.html?_nkw=dwa160&_frs=1) ( Amazon.com(http://www.amazon.com/s?field-keywords=DWA-160) has sale on this item! )

Before hacking/changing eeprom values, just plug that dongle into your TV. Some revisions might be workingwithout any change.

Also you have better to save original PID/VID values to somewhere to reverting your dongles back later.

You can check dongle PID/VID numbers via using lsusb command

For hacking dongles, all you need is plug the dongle to your linux computer and issue this commands.

# iwpriv ra0 e2p 208=04E8# iwpriv ra0 e2p 20A=2018

After you can look pid/vid values with lsusb command if they are changed or not... So your TV will think those dongles asoriginal Samsung one because of changed PID and VID values.

Notice: Not all rt2870sta chipped dongles compatible with this hack and you could broke your dongle with thiscommands. At least one "Edimax-uN7711" broken with this hack...

Also keep in mind that, some USB dongles with same Model number might have different revisions and could havedifferent chips in it or could incompatible with this hack. If you faced with one, please report us.

Compiling Custom Kernel Modules that supports e2p for Hardware Hack

e2p process might require you needed to compile new wifi from source drivers if your driver doesn't support e2p.

For Ubuntu/Debian Linux

sudo apt-get updatesudo apt-get upgradesudo apt-get install build-essential linux-headers-$(uname -r) fakeroot dpkg-dev

Compiling your own driver

1. Go to http://www.ralinktech.com and download the RT2870USB(RT2870/RT2770)-Driver for Linux (site is very slow),or download a pre-modified version of the driver that WILL compile on kernels >= 2.6.35 (thanks | Mark Greaves(PCNetSpec) (http://linuxforums.org.uk/index.php?topic=852.msg4472#msg4472) )


2 of 8 08/04/2014 21:52

wget http://download.samygo.tv/Others/2010_0709_RT2870_Linux_STA_v2.4.0.1.tar.bz2

2. Type the following command:

tar -jxvf 2010_0709_RT2870_Linux_STA_v2.4.0.1.tar.bz2cd 2010_0709_RT2870_Linux_STA_v2.4.0.1

3. Open /os/linux/config.mk and change (this step is not neccessary if you only want to patch the stick and do not installthe driver):

# Support ATE functionHAS_ATE=y

# Support Wpa_SupplicantHAS_WPA_SUPPLICANT=y

# Support Native WpaSupplicant for Network MagangerHAS_NATIVE_WPA_SUPPLICANT_SUPPORT=y

4. Open /os/linux/usb_main_dev.c, add this code: MODULE_LICENSE("GPL"); (if it is not already there. This step isnot neccessary for the driver listed above). So it should look like:

MODULE_AUTHOR("Paul Lin <[email protected]>");MODULE_DESCRIPTION("RT2870 Wireless Lan Linux Driver");MODULE_LICENSE("GPL");#ifdef CONFIG_STA_SUPPORT#ifdef MODULE_VERSIONMODULE_VERSION(STA_DRIVER_VERSION);#endif#endif // CONFIG_STA_SUPPORT //

5. Compiling driver:

make

Some output:

make -C toolsmake[1]: Entering directory `/tmp/2010_0709_RT2870_Linux_STA_v2.4.0.1/tools'gcc -g bin2h.c -o bin2hmake[1]: Leaving directory `/tmp/2010_0709_RT2870_Linux_STA_v2.4.0.1/tools'/tmp/2010_0709_RT2870_Linux_STA_v2.4.0.1/tools/bin2hcp -f os/linux/Makefile.6 /tmp/2010_0709_RT2870_Linux_STA_v2.4.0.1/os/linux/Makefilemake -C /lib/modules/2.6.32-24-generic-pae/build SUBDIRS=/tmp/2010_0709_RT2870_Linux_STA_v2.4.0.1/os/linux modulesmake[1]: Entering directory `/usr/src/linux-headers-2.6.32-24-generic-pae' CC [M] /tmp/2010_0709_RT2870_Linux_STA_v2.4.0.1/os/linux/../../common/crypt_md5.o CC [M] /tmp/2010_0709_RT2870_Linux_STA_v2.4.0.1/os/linux/../../common/crypt_sha2.o CC [M] /tmp/2010_0709_RT2870_Linux_STA_v2.4.0.1/os/linux/../../common/crypt_hmac.o CC [M] /tmp/2010_0709_RT2870_Linux_STA_v2.4.0.1/os/linux/../../common/crypt_aes.o......... CC [M] /tmp/2010_0709_RT2870_Linux_STA_v2.4.0.1/os/linux/../../common/rtusb_io.o CC [M] /tmp/2010_0709_RT2870_Linux_STA_v2.4.0.1/os/linux/../../common/rtusb_bulk.o CC [M] /tmp/2010_0709_RT2870_Linux_STA_v2.4.0.1/os/linux/../../common/rtusb_data.o CC [M] /tmp/2010_0709_RT2870_Linux_STA_v2.4.0.1/os/linux/../../common/cmm_data_usb.o CC [M] /tmp/2010_0709_RT2870_Linux_STA_v2.4.0.1/os/linux/../../common/ee_prom.o CC [M] /tmp/2010_0709_RT2870_Linux_STA_v2.4.0.1/os/linux/../../common/rtmp_mcu.o CC [M] /tmp/2010_0709_RT2870_Linux_STA_v2.4.0.1/os/linux/../../common/rtusb_dev_id.o CC [M] /tmp/2010_0709_RT2870_Linux_STA_v2.4.0.1/os/linux/../../os/linux/rt_usb.o CC [M] /tmp/2010_0709_RT2870_Linux_STA_v2.4.0.1/os/linux/../../os/linux/rt_usb_util.o CC [M] /tmp/2010_0709_RT2870_Linux_STA_v2.4.0.1/os/linux/../../os/linux/usb_main_dev.o LD [M] /tmp/2010_0709_RT2870_Linux_STA_v2.4.0.1/os/linux/rt2870sta.o Building modules, stage 2. MODPOST 1 modules CC /tmp/2010_0709_RT2870_Linux_STA_v2.4.0.1/os/linux/rt2870sta.mod.o LD [M] /tmp/2010_0709_RT2870_Linux_STA_v2.4.0.1/os/linux/rt2870sta.komake[1]: Leaving directory `/usr/src/linux-headers-2.6.32-24-generic-pae'

Note: You may see a LOTs of warnings during the compilation, and this is *normal* so don't panic.


3 of 8 08/04/2014 21:52

Installation is not neccessary for patching, but after this you get your driver permanent

sudo make install

6. Insert the stick and ensure, that you unload every drivermodule that was loaded automatically. Otherwise you cannotload your custom driver

sudo rmmod rt2870stasudo rmmod rt2800usbsudo rmmod rt2x00usbsudo rmmod rt2800libsudo rmmod rt2x00libsudo rmmod [all other ralinktech modules]

Check with "lsmod | grep rt" if all ralinktech-related modules are unloaded. Maybe you must also shutdown the wlaninterface (ifconfig wlan0 down) if you get a "device busy" error.

sudo rmmod [module-if-exists]

7. Load your custom driver

sudo insmod os/linux/rt3070sta.ko# bring the interface up (this is important, otherwise iwpriv quits with an error)sudo ifconfig ra0 up

8. Insert your wifi stick and look supported ioctl table like that

user@localhost:~# sudo iwpriv ra0ra0 Available private ioctls : set (8BE2) : set 1024 char & get 0 connStatus (0004) : set 1024 char & get 2047 char driverVer (0005) : set 1024 char & get 2047 char bainfo (0006) : set 1024 char & get 2047 char descinfo (0007) : set 1024 char & get 2047 char radio_off (000A) : set 1024 char & get 2047 char radio_on (000B) : set 1024 char & get 2047 char show (0015) : set 1024 char & get 2047 char adhocEntry (0016) : set 1024 char & get 2047 char bbp (8BE3) : set 2047 char & get 2047 char mac (8BE5) : set 1024 char & get 1024 char rf (8BF3) : set 2047 char & get 2047 char e2p (8BE7) : set 1024 char & get 1024 char stat (8BE9) : set 0 & get 2047 char get_site_survey (8BED) : set 0 & get 1024 char

9. Watch lsmod to current PID/VID. Take note that values

10. change VID&PID with the commands.

user@localhost:~# sudo iwpriv ra0 e2p 208=04E8ra0 e2p:0208=0x04E8user@localhost:~# sudo iwpriv ra0 e2p 20A=2018ra0 e2p:020A=0x2018

11.Verify changed values

user@localhost:~# sudo iwpriv ra0 e2p 0208ra0 e2p:[0x0208]:0x04E8user@localhost:~# sudo iwpriv ra0 e2p 020ara0 e2p:[0x020A]:0x2018

Now the stick should be recognized by your TV

Written wrong values? Fix driver.


4 of 8 08/04/2014 21:52

Smetimes it happens, the procedure goes w/o error, but you get wrong VID and PID written to dongle`s eeprom. Here isthe solution.You have to add your new values to driver, compille it and insmod. Then dongle will be recognized by system again.

1. Open ./common/rtusb_dev_id.c, locate the following section:

#ifdef RT2870 {USB_DEVICE(0x148F,0x2770)}, /* Ralink */ {USB_DEVICE(0x148F,0x2870)}, /* Ralink */ {USB_DEVICE(0x07B8,0x2870)}, /* AboCom */ ... {USB_DEVICE(0x050d,0x815c)}, /* Belkin F5D8053 */ {USB_DEVICE(0x100D,0x9031)}, /* Motorola 2770 */ {USB_DEVICE(0x0DB0,0x6899)},#endif // RT2870 //

2. Add a new line (before the #endif // RT2870 // line) with your new values, (replace with yours):

{USB_DEVICE(0x04E8,0x7718)},

3. Recompile driver (http://wiki.samygo.tv/index.php5/Using_NoN-Samsung_USB_WiFi_dongles_with_TV#Compiling_Custom_Kernel_Modules_that_supports_e2p_for_Hardware_Hack).Try change vid&pid according howto again.

Software WayInstructions

For B series only. Same approach will work on C series (with C series kernel modules, but except rt73 based dongles...)

Open Telnet/Console Connection to your TV via SamyGO Telnet Enabler if it's not already enabled by Hackedfirmware or you can use console approach too.Download the pre-compiled drivers from SamyGO WiFi Modules here (http://download.samygo.tv/B%20Series/Kernel%20Modules/SamyGO%20WiFi%20Extension%20Addon%20v0.02.zip)Extract and copy required ko modules to usb, then TV's internal memory like "/mtd_rwarea/modules" (or you canleave them on USB...)

md /mtd_rwarea/modulescp /dtv/usb/sda/SamyGO/rt73.ko /mtd_rwarea/modules

Than load the modules to TV's kernel.

Basic Way

rmmod rt73 # remove old kernel modulesleep 10 # wait some for detectioninsmod /mtd_rwarea/modules/rt73.ko # install new module, you can also replace with rt73 or rt2570sta.ko or rt2870sta

Advanced Way

If commands at top doesn't work properly, you can try this way.

killall -QUIT udhcpc # stops udhcpcifconfig ra11n0 down # shut downs nw interfacermmod rt2870sta # removes original modulermmod rt73 # removes original module insmod /mtd_rwarea/modules/rt2870sta.ko # load new module, you can also replace with rt73 or rt2570sta.koifconfig ra11n0 up # fire up nw interfaceudhcpc -i ra11n0 -t 12 -T 5 -b # start udhcpc


5 of 8 08/04/2014 21:52

After your TV recognizes USB WiFi dongle that you have. You can also use another chipped WiFi dongles too. Butdefinitely you needed to find linux drivers compatible with 2.6.17/18 and needed to compile them via Toolchain providedby SamyGO Open Embedded.

You can check output by:

#dmesg | grep rtu<7>rtusb_disconnect: unregister_netdev(), dev->name=ra11n0!<4><--- rtusb 2870 1.002(1.4.0.0) exit<4>rtusb 2870 1.002(1.4.0.0) init ---><4>rtusb 0.994 init ====><4><=== rtusb 0.994 exit<7>rtusb_disconnect: unregister_netdev(), dev->name=ra11n0!<4><--- rtusb 2870 1.002(1.4.0.0) exit<4>rtusb 2870 1.002(1.4.0.0) init ---><4>rtusb 0.994 init ====><4><=== rtusb 0.994 exit<4>rtusb 0.994 [SamyGO] init ====><4><=== rtusb 0.994 [SamyGO] exit<7>rtusb_disconnect: unregister_netdev(), dev->name=ra11n0!<4><--- rtusb 2870 1.002(1.4.0.0) exit<4>rtusb 2870 1.002(1.4.0.0) [SamyGO] init ---><4>rtusb 0.994 [SamyGO] init ====>

Debugging

With creating file on dtv, triggers debug with USB connection. touch /dtv/debug_on

USB WiFi dongles that uses RaLink chip/driver

You can use any of rt73,rt2570 and rt2870 chipped dongles. Some of them could generate problems on connectingWPA/WEP protected networks.

Dongles that tested on forum

Edimax EW-7318USgEdimax EW-7711UAN (rt2870sta)Edimax EW-7718UN (rt2870sta)<please fill here if your USB dongle that works with ralink driver, need specified model number>

Dongles that we insist working on this TV

Informations extracted from our compiled drirvers (this is the preferred version) (http://download.samygo.tv/Documents/Dongle%20Driverlist%20for%20SamyGO%20Project.pdf)

I search on internet and found this 2 lists:

uses rt2850.ko http://wiki.debian.org/rt2870sta uses rt73.ko http://wiki.debian.org/WiFi/rt73

also those that uses rt2870sta.ko:

USB: 0471:200F Philips 802.11n Wireless AdapterUSB: 04E8:2018 Samsung Electronics Co., Ltd (Device name unknown)USB: 050D:8053 Belkin Components (Device name unknown)USB: 050D:805C Belkin Components (Device name unknown)USB: 0586:3416 ZyXEL Communications Corp. NWD-210N 802.11b/g/n-draft wireless adapterUSB: 0789:0162 Logitec Corp. (Device name unknown)USB: 0789:0163 Logitec Corp. (Device name unknown)USB: 0789:0164 Logitec Corp. (Device name unknown)USB: 07AA:002F Corega K.K. CG-WLUSB2GNLUSB: 07AA:003C Corega K.K. (Device name unknown)USB: 07AA:003F Corega K.K. (Device name unknown)USB: 07B8:2770 D-Link Corp. (Device name unknown)USB: 07B8:2870 D-Link Corp. (Device name unknown)USB: 07B8:3070 D-Link Corp. (Device name unknown)USB: 07B8:3071 D-Link Corp. (Device name unknown)USB: 07D1:3C09 D-Link System DWA-140 802.11n Adapter [ralink rt2870]


6 of 8 08/04/2014 21:52

USB: 07D1:3C11 D-Link System (Device name unknown)USB: 083A:6618 Accton Technology Corp. 802.11n Wireless AdapterUSB: 083A:7522 Accton Technology Corp. 802.11N Wireless AdapterUSB: 083A:A618 Accton Technology Corp. SMC EZ Connect N Draft 11n Wireless AdapterUSB: 083A:B522 Accton Technology Corp. EZ Connect N Draft 11n Wireless USB2.0 AdapterUSB: 0B05:1731 ASUSTek Computer, Inc. ASUS 802.11n Network AdapterUSB: 0B05:1732 ASUSTek Computer, Inc. 802.11n Network AdapterUSB: 0B05:1742 ASUSTek Computer, Inc. 802.11n Network AdapterUSB: 0CDE:0022 Z-Com 802.11b/g/n Wireless Network AdapterUSB: 0CDE:0025 Z-Com (Device name unknown)USB: 0DF6:0017 Sitecom Europe B.V. WL-182USB: 0DF6:002B Sitecom Europe B.V. (Device name unknown)USB: 0DF6:002C Sitecom Europe B.V. (Device name unknown)USB: 0DF6:002D Sitecom Europe B.V. (Device name unknown)USB: 0DF6:0039 Sitecom Europe B.V. (Device name unknown)USB: 0DF6:003F Sitecom Europe B.V. (Device name unknown)USB: 0E66:0001 Hawking (Device name unknown)USB: 0E66:0003 Hawking (Device name unknown)USB: 1044:800B Chu Yuen Enterprise Co., Ltd GN-WB30N 802.11n WLAN CardUSB: 129B:1828 CyberTAN Technology (Device name unknown)USB: 13D3:3247 IMC Networks 802.11 n/g/b Wireless LAN AdapterUSB: 1482:3C09 (Vendor name unknown) (Device name unknown)USB: 148F:2770 Ralink Technology, Corp. (Device name unknown)USB: 148F:2870 Ralink Technology, Corp. (Device name unknown)USB: 148F:3070 Ralink Technology, Corp. (Device name unknown)USB: 14B2:3C06 Ralink Technology, Corp. (Device name unknown)USB: 14B2:3C07 Ralink Technology, Corp. (Device name unknown)USB: 14B2:3C09 Ralink Technology, Corp. (Device name unknown)USB: 14B2:3C12 Ralink Technology, Corp. (Device name unknown)USB: 14B2:3C23 Ralink Technology, Corp. (Device name unknown)USB: 14B2:3C25 Ralink Technology, Corp. (Device name unknown)USB: 14B2:3C27 Ralink Technology, Corp. rt2870 802.11n WLANUSB: 14B2:3C28 Ralink Technology, Corp. (Device name unknown)USB: 157E:300E TRENDnet (Device name unknown)USB: 15A9:0006 (Vendor name unknown) (Device name unknown)USB: 15C5:0008 (Vendor name unknown) (Device name unknown)USB: 1737:0071 Linksys (Device name unknown)USB: 1740:9701 Senao (Device name unknown)USB: 1740:9702 Senao (Device name unknown)USB: 18C5:0012 AMIT (Device name unknown)USB: 2019:AB25 PLANEX (Device name unknown)USB: 2019:ED06 PLANEX (Device name unknown)USB: 5A57:0280 Zinwell (Device name unknown)USB: 5A57:0282 Zinwell (Device name unknown)USB: 7392:7711 (Vendor name unknown) (Device name unknown)USB: 7392:7717 (Vendor name unknown) (Device name unknown)

and for rt73.ko

USB: 0411:00F4 MelCo., Inc. (Device name unknown)USB: 050D:7050 Belkin Components F5D7050 ver 1000 WiFiUSB: 050D:705A Belkin Components F5D7050A Wireless AdapterUSB: 050D:905B Belkin Components F5D9050 ver 3 Wireless AdapterUSB: 050D:905C Belkin Components Wireless G Plus MIMO Network AdapterUSB: 06F8:E010 Guillemot Corp. HWGUSB2-54-LBUSB: 06F8:E020 Guillemot Corp. HWGUSB2-54V2-APUSB: 0769:31F3 Surecom Technology Corp. RT2573USB: 07AA:002E Corega K.K. (Device name unknown)USB: 07B8:B21D D-Link Corp. RT2573USB: 07D1:3C03 D-Link System DWL-G122 802.11g Adapter [ralink rt73]USB: 07D1:3C04 D-Link System WUA-1340USB: 07D1:3C06 D-Link System (Device name unknown)USB: 07D1:3C07 D-Link System Wireless G DWA-110 AdapterUSB: 0B05:1723 ASUSTek Computer, Inc. WL-167G v2 802.11g Adapter [ralink]USB: 0B05:1724 ASUSTek Computer, Inc. RT2573USB: 0DB0:6874 Micro Star International RT2573USB: 0DB0:6877 Micro Star International RT2573USB: 0DB0:A861 Micro Star International RT2573USB: 0DB0:A874 Micro Star International RT2573USB: 0DF6:90AC Sitecom Europe B.V. WL-172USB: 0DF6:9712 Sitecom Europe B.V. WL-113 rev 2USB: 1044:8008 Chu Yuen Enterprise Co., Ltd GN-WB01GSUSB: 1044:800A Chu Yuen Enterprise Co., Ltd GN-WI05GSUSB: 1371:9022 Dick Smith Electronics RT2573USB: 1371:9032 Dick Smith Electronics C-Net CWD-854 rev FUSB: 13B1:0020 Linksys WUSB54GC 802.11g Adapter [ralink rt73]USB: 13B1:0023 Linksys WUSB54GRUSB: 1472:0009 Huawei-3Com Aolynk WUB320gUSB: 148F:2573 Ralink Technology, Corp. RT2501USB Wireless AdapterUSB: 148F:2671 Ralink Technology, Corp. RT2601USB Wireless AdapterUSB: 14B2:3C22 Ralink Technology, Corp. rt73 802.11g WLANUSB: 15A9:0004 (Vendor name unknown) (Device name unknown)USB: 1631:C019 Good Way Technology RT2573USB: 1690:0722 Askey Computer Corp. [hex] RT2573USB: 1740:7100 Senao (Device name unknown)USB: 18E8:6196 Qcom RT2573USB: 18E8:6229 Qcom RT2573


7 of 8 08/04/2014 21:52

USB: 18E8:6238 Qcom (Device name unknown)USB: 2019:AB01 PLANEX GW-US54HPUSB: 2019:AB50 PLANEX GW-US54Mini2

Forum PageYou can leave comment on this related forum. http://forum.samygo.tv/viewtopic.php?f=3&t=14

Retrieved from "http://wiki.samygo.tv/index.php5?title=Using_NoN-Samsung_USB_WiFi_dongles_with_TV&oldid=3728"

This page was last modified on 6 March 2013, at 14:27.This page has been accessed 295,700 times.Content is available under GNU Free Documentation License 1.3 or later unless otherwise noted.


8 of 8 08/04/2014 21:52