Using the GPIB Interface 7 Communication Interface Manual

Part No. IB027584Apr 2021

PBZ20-20PBZ20-20APBZ40-10PBZ60-6.7PBZ80-5

BIPOLAR POWER SUPPLY PBZ Series

Communication Interface Manual

About the Operation Manuals 2Notations Used in This Manual 2

Remote Control Overview 3VISA Library 4

Interface Setup 5Using the RS232C Interface 5Using the GPIB Interface 7Using the USB Interface 8Using the LAN Interface (Option) 9Accessing and Operating the PBZ from a Web Browser (LAN interface) 11

Message Overview 14SCPI Command Syntax 14Parameters 17

Command Description in This Manual 19

IEEE 488.2 Common Commands 20Output Setting Commands 24

CV/CC Mode and Bipolar/Unipolar Mode 24Selecting the Signal Source (Internal or External) and Setting the External Signal Source 24DC Signal Setting 26Output, Trigger Signals, and Screen Contrast 36

Protection Features Commands 39Mode 39Activation points (OCP/OVP) 39Activation points (I.LIM/ V.LIM) 41Mode and activation points (legacy command) 42Clearing Alarms 43

Measurement Function Commands 44Trigger Function 45

Memory Function Commands 53Preset Memory 53Setup Memory 53

Sequence Function Commands 55Editing Programs and Steps 55Executing Programs 64Editing Scripts 65

System Settings Commands 66CONFIG Settings 66Basic System Settings 70IEEE 488.2 Register Model 74SCPI Register Model 76

Default State 81Processing time of Commands 86List of Messages 87List of Errors 96Tutorial (Visual Basic 2008) 99

INDEX103

2 PBZ_INTERFACE

There are five PBZ Series Manuals listed as follows.

• Setup Guide This manual is intended for first-time users of this product. It provides an overview of the product and notes on usage. It also explains how to set up the product for testing the DUT. Always read this manual before using the product.

• User’s Manual This manual is intended for first-time users of this product. It provides an overview of the product and notes on usage. It also explains how to configure the product, operate the product, perform maintenance on the product, and so on.

• Communication Interface Manual (this manual)This manual contains details about remotely controlling the tester using SCPI commands.The interface manual is written for readers with sufficient basic knowledge of how to control measuring instruments using a PC.

• Quick Reference This manual explains Panel description and operation briefly.

• Safety Information This document contains general safety precautions for this product. Keep them in mind and make sure to observe them.

PBZ series manuals is intended for users of the product or persons teaching other users on how to operate the bipolar power supply.

PBZ series manuals assumes that the reader has electrical knowledge.

PDF is provided on the included CD-ROM. Adobe Acrobat Reader is required to view the PDF file.

Product firmware versionsThis manual applies to products with firmware versions 2.2X (PBZ20-20/ PBZ40-10/ PBZ60-6.7/ PBZ80-5), 1.0X (PBZ20-20A).

When contacting us about the product, please provide us with:The model (marked in the top section of the front panel)The firmware version (see the user’s manual)The serial number (marked in the top section of the rear panel)

Before reading this manualFirst read the User’s Manual, which includes information on the product’s hardware, to avoid connecting or operating the product incorrectly.

TrademarksCompany names and product names used in this manual are trademarks or registered trademarks of their respective companies.

CopyrightsThe contents of this manual may not be reproduced, in whole or in part, without the prior consent of the copyright holder.

The specifications of this product and the contents of this manual are subject to change without prior notice.

© 2013 Kikusui Electronics Corporation

• The bipolar power supply PBZ series is referred to as the PBZ in this manual.

• The word “PC” used in this manual is a generic term for personal computers and workstations.

• The following markings are used in this manual.

Indicates a potentially hazardous situation which, if ignored, could result in death or serious injury.

Indicates a potentially hazardous situation which, if ignored, may result in damage to the product or other property.

Indicates information that you should know.

Explanation of terminology or operation principle.

Indicates reference to detailed information.

About the Operation Manuals

PaperPaper PDF

PDF

PDF

PaperPaper PDF

PaperPaper PDF

Notations Used in This Manual

WARNING

CAUTION

DESCRIPTION

See

PBZ_INTERFACE 3

1 Remote Control Overview

This chapter provides a general explanation of the remote control function.

In addition to controlling the PBZ from the front panel, you can control it remotely through the following standard-equipped interfaces.

• RS232C interface• GPIB interface• USB interface• LAN interface (factory option)

If the factory option interface board is installed, you can use LAN.You cannot control the PBZ through RS232C, GPIB, USB, and LAN at the same time.The remote interfaces comply with IEEE Std 488.2-1992 and SCPI Specification 1999.0.

p. 14 Familiarize yourself with the syntax of the SCPI commands that are used with the PBZ before you use them to control the product.

The RMT icon is displayed in the screen’s status display area when the PBZ is in remote mode. To use the front panel to switch the PBZ back to local mode, press the LOCAL key.

Measurement instrument interface standards

The PBZ complies with the following standards.

• IEEE Std 488.2-1992 IEEE Standard Codes, Formats, Protocols, and Common Commands For Use With IEEE Std 488.1-1987

• IEEE Std 488.1-1987 IEEE Standard Digital Interface for Programmable Instrumentation• Standard Commands for Programmable Instruments (SCPI) version 1999.0• Universal Serial Bus Specification Rev 2.0• Universal Serial Bus Test and Measurement Class Specification (USBTMC) Rev 1.0• Universal Serial Bus Test and Measurement Class, Subclass USB488 Specification

(USBTMC-USB488) Rev 1.0• TCP/IP Instrument Protcol Specification VXI-11• LXI 1.4 Core Device Specification 2011

See

4 PBZ_INTERFACE

Remote Control Overview

VISA Library

To use the VISA library (VISA COM) with the I/O library, the VISA library must be installed on the controller (the host PC).To use the USB interface to control the PBZ, a driver that supports the USB Test & Measurement Class (USBTMC) must be installed on the controller. The USBTMC driver is installed automatically by the VISA library.When the product is controlled by the LAN interface, middleware which applies to the VXI-11 protocol is required. Middleware is automatically installed by VISA library. VISA (Virtual Instrument Software Architecture) was developed by the VXIplug&play Systems Alliance. It is the standard specification for measurement instrument connection software.

You have to install one of the following VISA libraries (driver software that is implemented according to the VISA specifications).Do not install multiple VISA libraries on the same PC. Doing so may cause errors.VISA libraries that are older than the versions listed here do not support USB.

• NI-VISA by National Instruments Corporation (version 5.1.1 or later)• Keysight VISA by Keysight Technologies, Inc. (Keysight IO Librarys Suite 16.0 or later)• KI-VISA version 5.0..4 or later

KI-VISA is an original VISA library developed by Kikusui Electronics Corporation that supports the VXIplug&play VISA specifications. You can download the most recent version of this library from the Kikusui Electronics Corporation website (http://www.kikusui.co.jp/ download/). If NI-VISA or Keysight VISA is already installed on your PC, you do not need to install KI-VISA.

You can download the “KI-VISA Library Programming Guide” from the Kikusui Electronics Corporation website.

PBZ_INTERFACE 5

2 Interface Setup

Using the RS232C Interface

The PBZ RS232C interface is a standard D-sub, 9-pin male connector.Check that the PBZ and your PC are off, and connect them with a standard cross cable (null- modem cable).Use a D-sub, 9-pin, female-to-female AT cross cable. The figure below shows the port pinout.The PBZ does not use hardware handshaking (cross cable example 2).

1

2

3

4

5

6

7

8

9

1

2

3

4

5

6

7

8

9

D-sub 9-pin female

D-sub 9-pin female

Cross cable example 1

1

2

3

4

5

6

7

8

9

1

2

3

4

5

6

7

8

9

D-sub 9-pin female

D-sub 9-pin female

Cross cable example 2

#4-40UNCinch screw

#4-40UNCinch screw

1: CD (carrier detect)2: RXD (receive data)

3: TXD (transmit data)4: DTR (data terminal ready)

5: GND (signal ground)

6: DSR (data set ready)7: RTS (request to send)

8: CTS (clear to send)9: RI (ring indicator)

Facing the PBZ rear panel

6 PBZ_INTERFACE

Interface Setup

RS232C Settings

Press Config key to set the interface type and communication parameters using CONFIG[6].

Protocol

The RS232C protocol. In the following table, the underlined values are the factory default settings.

Flow control

Use flow control for RS232C transmission and reception. Device Control (DC) codes are used for this purpose.Data may not be received properly if flow control is not used.

Break signal

The break signal is used as a substitute for the IEEE488.1 dcl/sdc (Device Clear, Selected Device Clear) message.

Item Setting

Connector Rear panel, D-sub, 9-pin connector

Baud rate 1 200, 2 400, 4 800, 9 600, 19 200, or 38 400 bps

Data length 7 or 8

Stop bits 1 or 2

Parity None (fixed)

Flow control ON or OFF

Code Function ASCII code

DC1 (Xon) Request to send 11H

DC3 (Xoff) Transmission stop request 13H

Resume transmissionDC3TXD

PBZ

RXD

After receiving DC3, the RS232C terminal must pause transmission within 10 characters.

Within 10 characters

DC1Pause

PBZ_INTERFACE 7

Interface Setup

Using the GPIB Interface

Setting the GPIB address

The factory default GPIB address is “1.” You can set the address to a number from 1 to 30.Press Config key to set the interface type and GPIB address using CONFIG[6].

GPIB feature

Service request

The PBZ is equipped with service request and serial polling functions.

Function Subset Description

Source handshaking SH1 Full capability

Acceptor handshaking AH1 Full capability

Talker T6 Function available

Listener L4 Function available

Service request SR1 Full capability

Remote local RL1 Full capability

Parallel polling PP0 No capability

Device clear DC1 Full capability

Device trigger DT1 Full capability

Controller C0 No capability

Electrical interface E1 Open-collector driver

8 PBZ_INTERFACE

Interface Setup

Using the USB Interface

To use the USB interface to control the PBZ, a driver that supports the USB Test & Measurement class (USBTMC) must be installed on the controller. The USBTMC driver is installed automatically by the VISA library.

USB settings

Press Config key to set the interface type using CONFIG[6].

USB feature

• Complies with USB specification 2.0• Complies with USBTMC specification 1.0 and USBTMC-USB488 specification 1.0• Baud rate: 12 Mbps maximum (full speed)• VID (vendor ID): 0x0B3E• PID (product ID): 0x1012

Service request


PBZ_INTERFACE 9

Interface Setup

Using the LAN Interface (Option)

The LAN interface is a factory option.To use the LAN interface to control the PBZ, middleware that supports the VXI-11 protocol must be installed on the controller. The middleware is installed automatically by the VISA library.There is a Web browser interface to the PBZ embedded in the LAN interface board. You can configure the LAN interface settings from your PC’s Web browser.For information on topics such as connecting to your corporate LAN, your IP address, your host name, and security, contact your network administrator.

LAN connections

Use a standard LAN cable (category 5 and straight) to connect the PBZ to a network hub or router. Use a crossover cable when making a direct connection.

LAN settings

Usually, LAN settings are configured using a DHCP server. If you want to use a fixed IP address, you cannot set it from the panel. Set it from a Web browser.

CONFIG settings

Press Config key to set the interface type and communication parameters using CONFIG[6].

p. 11 Normally, you should set DHCP and AUTO IP to ON to set the IP address automatically.For direct connections, set DHCP to OFF and AUTO IP to ON and set the IP address automatically.You cannot set the IP address from the panel. To set a fixed IP address, first set the IP address automatically, and then set a fixed address by accessing the PBZ through a Web browser.When you are going to use a fixed IP address over a long period of time or at intervals, we recommend that you specify a host name. To set a host name, access the PBZ through a Web browser.

Service request


LAN feature

Depending on the operation that you perform through your Web browser, the PBZ may need to connect to the Internet.Complies with the LXI 1.4 Core 2011Complies with the VXI-11/ SCPI-RAW protocolBaud rate: 100 Mbps maximum (auto negotiation)DHCP client featureAUTO IP featureFrom your Web browser, you can (Internet Explorer; Mozilla Firefox; Safari/ Mobile Safari; Google Chrome):

Change LAN and security settings.Use simple control applications.Update the LAN board

See

10 PBZ_INTERFACE

Interface Setup

LAN RESET switch and DEFAULT switch

� LAN RESET switchHolding down this switch for 3 seconds resets the LAN interface settings, except for Hostname and Hostname Description, to their factory default values. You can use this switch if you forget the security password.

� DEFAULT switchHold down this switch for 3 seconds or more to reset the LAN interface settings to the factory default values. You can use this switch if you forget the security password or IP address.Neither of these switches affects the PBZ’s panel settings. If the PBZ is in remote mode, pressing one of these switches will change the PBZ back into local mode (panel operation).

DEFAULT

DEFAULT switchLAN RESET switch

* Use a thin-tipped tool to press the switches.

WARNING • The LAN interface can be accessed from anywhere on the network that the PBZ is connected to. Change the security settings if necessary. Refer to " Accessing and Operating the PBZ from a Web Browser (LAN interface)" on p. 11 for setting procedure.

• Do not use the DEFAULT and LAN RESET switches carelessly. This may cause the LAN interface to malfunction.

• The LAN interface is different from the other remote interfaces in that you have to use the “SYSTem:REMote” command to switch the PBZ to remote mode. When you are carrying out remote programming, send this command at the beginning of the program.

PBZ_INTERFACE 11

Interface Setup

Accessing and Operating the PBZ from a Web Browser (LAN interface)

For LAN interface, the detailed setting can be operated from the browser on the PC.The URL of Web site is defined as adding "http://" in front of the IP address.The URL can be entered directly on the address bar of the browser by confirming the IP address of the config setting (CONFIG[6] > LAN > IP ADDRESS).

(Example) When the IP address is 169.254.7.8http://169.254.7.8

When VISA library is used, there is the function to retrieve the VXI-11 measuring instrument by the application program provided by VISA vendors (National Instruments NI-MAX, Agilent Connection Expert, and Kikusui KI-VISA Instrument Explorer, etc.). You can access the PBZ by clicking on the Web link from the retrieval results.

The following browsers are applied.• Internet Explorer• Mozilla Firefox• Google Chrome• Safari/ Mobile Safari

WELCOME page

When you access the PBZ from a Web browser, the WELCOME page is displayed first.The instrument information, network information, and VISA resource (I/O resource) information appear on the display.Clicking Turn ON Identify displays “Device Identify” on the PBZ series front panel display. This enables you to check which PBZ series is being controlled through the LAN interface.Click the navigation menu to move to the other page.

Navigation menuMove to the page which clicked.

12 PBZ_INTERFACE

Interface Setup

Remote Control page

You can set and control voltage, current, and output settings; view measured values; configure the protection feature.

LAN config page

Config page for the network settings.Click Modify Now to assign the IP address, set the host name, and so on.If you set the host name, you can use it in place of the IP address to access the LAN interface.After you enter the settings, click Apply to apply the settings.

The input form for the item you click appears in the lower area.

Output: on/off

Enter the settings and click Enter to change the PBZ settings.

Monitor

PBZ_INTERFACE 13

Interface Setup

STATUS page

This page shows the LAN board revision and OSS license information.

SECURITY page

This page is for the security setting.This page can allow you to set the change of the password protection.The password protection is an effective security features to the Web site. It prevents from being changed inadvertently. The password can be used for any alphanumeric characters, the hyphen, and the underscore.

14 PBZ_INTERFACE

3 Message Overview

The information that is transferred between the controller (the host PC) and the PBZ is referred to as “messages.”The PBZ uses the SCPI language for these messages.The messages that the PC sends to the PBZ are commands. The messages that the PBZ sends to the PC are responses.Commands are used to execute functions or change settings on the PBZ or to query the PBZ’s settings or status. Responses are used to return the PBZ’s settings or status.

SCPI Command Syntax

Command hierarchy

SCPI is an ASCII-based command language that was designed for test and measuring equipment. The command structure is composed of the common roots and nodes that are the building blocks of the SCPI subsystem. A command consists of a program header, parameters, and punctuation marks.The following table uses the SOURce subsystem as an example to explain the hierarchy.

• A colon (:) separates a higher node from a lower node.• If the program header starts with a colon, the first node is a root node.

Program header Parameter Node levelSOURce Root node

:SWEep 2nd level:FREQuency 3rd level

:STARt <numeric> 4th level:STOP <numeric> 4th level

:FUNCtion {SIN|SQE|TRI|USER[1]...USER[16]}

2nd level

PBZ_INTERFACE 15

Message Overview

Command syntax

� Format

In this manual, SCPI commands are expressed in the following format.

Example:[SOURce:]FUNCtion[:SHAPe][:IMMediate]

{SINusoid|SQUare|TRIangle|USER[1]..USER16}

• SCPI commands can be written in long form (with all the characters) or in short form (omitting the lowercase characters). SCPI commands can be transmitted in either long form or short form.

• SCPI commands are not case sensitive. VOLT, Volt, and volt are all received as the short form of the VOLTage command. VOLUME, Volume, and volume are all received as the long form of the VOLume command.

• A space separates a program header and its parameters.• Multiple parameters are separated by commas.

� Compound commands

Compound commands can be created by concatenating two commands with a semicolon.

Example (compound command):CURRent:PROTection:LOWer -5.0;UPPer 10.0

You can use a compound command to send a command that is the same as the two following commands.

Example (individual commands):CURRent:PROTection:LOWer -5.0CURRent:PROTection:UPPer 10.0

In the first command, CURRent:PROTection:LOWer -5.0, the path is set to CURRent: PROTection. Therefore, in the second command, CURRent:PROTection can be omitted.If you specify a node that is not defined in the current path (except for OVER, UND, UPP, LOW, STAT, and PASS), an error will occur.

� Compound command (clearing the specified path)

Example:SENSe:FUNCtion DC;:INITiate

There are two root nodes in this compound command: SENSe and INITiate. When the second command or later begins with a colon, the path that was specified by the previous command is cleared.

• Program headers are separated by colons.• By using colons and semicolons, you can concatenate commands of different

subsystems.• The maximum length of a command that you can transmit on a single line is 128 bytes.

16 PBZ_INTERFACE

Message Overview

Special symbols and characters

The special symbols and characters that are used in this manual for the SCPI command syntax are explained below.

Queries

You can query the PBZ settings and status.To make a query, append a question mark to the end of the program header section. If the query has parameters, insert a space after the question mark, and then write the parameters.

Example:VOLTAGE:AC? MIN

Terminating character strings

All commands must be terminated with a valid terminator.The available terminators are <line feed> (ASCII 0x0A) and EOI (end-or-identify). You can use any one of these terminators to terminate a command.EOI does not exist in the RS232C specification, so be sure to use <line feed>.When you terminate a command string, the path is reset to the root level.

Common commands

p. 20 There are commands that are common to the IEEE-488.2 and SCPI standards for functions such as resetting devices and performing self-diagnoses. These common commands start with an asterisk (“*”). These commands may have one or multiple parameters.

Symbol or character

Description

< > Character strings inside the < and > symbols indicate program data.Do not include the < and > symbols in the actual program.

{ }Characters and numbers delimited by “|” inside the { and } symbols indicate that one of the delimited items is to be selected.Do not include the { and } symbols in the actual program.

[ ]Character strings inside [ and ] indicate optional data.When optional data is not sent with the program, the default value is sent. Do not include the [ and ] symbols in the actual program.

If you want to send two queries on separate lines, send the second query after you have received the response to the first one. If you send query commands on two lines at the same time, you may receive an incomplete response.

CR (ASCII 0x0D) is not a terminator.

See

PBZ_INTERFACE 17

Message Overview

Parameters

The SCPI parameter format is derived from the program parameter format that is defined in IEEE 488.2.The program data expression format that the PBZ uses is shown below.

Non-numeric parameters

The PBZ uses the following three parameter types.

Numeric parameters

The PBZ uses the following five parameter types.

Symbol or character Description

String data(String)

Used when a series of ASCII characters are requested.Be sure to enclose strings in single or double quotation marks. The opening and closing quotation marks must match (you cannot mix single and double quotation marks).Example: PROGram NAME “PBZ”If you want to include a quotation mark as part of the string, enter consecutive quotation marks (with no characters between them). ASCII codes 20H to 7EH can be used in strings.

Character data(Character)

Used when only a limited number of values are available for a program setting. Responses are returned in short form.Example: TRIGger:SOURce {BUS|IMMediate}

Boolean data(Boolean)

Used to express a condition of 1 or 0, or ON or OFF. Responses are returned as 1 or 0.Example: OUTPut {ON|OFF|1|0}

Symbol or character Description

NR1 Represents an integer value.1

1 Details are given in the “IEEE 488.2 Standard Digital Interface for Programmable Instrumentation.”

NR2 Represents a real number in floating-point format.1

NR3Represents a real number in scientific notation.1Response data is normally returned with six decimal places.If the 380 is returned in the response data, it is returned as +3.800000+E02. This product has queries that return data with five decimal places.

NRf NRf is a generic term that includes NR1, NR2, and NR3.

Numeric

Represents values such as the decimal point, optional prefixes, and measurement units.Numbers are expressed the same as NRf.MINimum and MAXimum are available as substitutes for declaring certain values.You can also use units such as V, A, and S in numeric parameters.If a value that cannot be assigned is entered, the PBZ rounds the value to the closest possible value.Example: SYSTem:CONFigure:BEEPer:VOLume 0.56

The buzzer volume must be set to a value from 0.1 to 1.0, so if you send the query SYST:CONF:BEEP:VOL?, 0.6 will be returned.

18 PBZ_INTERFACE

Message Overview

Special form numeric parameters

The special form numeric parameters MINimum and MAXimum can be used as substitutes for the actual maximum and minimum values when the parameter is numeric.The following example sets the measurement time to the minimum value.SENSe:APERture MINimumYou can query the minimum and maximum values for most parameters.SENSe:APERture? MINSENSe:APERture? MAX

Measurement units

The default measurement units are listed below. Commands are accepted even if measurement units are not specified.

• A (current)• V (voltage)• A/V (current/voltage)• V/V (voltage/voltage)• W (power)• S (seconds) • PCT (%)• HZ (frequency)• DEG (degrees)

The following optional prefixes are supported. To enter “µ” in the parameter, use “U.”• M (milli)• K (kilo)• U (micro)

The unit symbols in the International System of Units contain lowercase characters. The IEEE standard uses uppercase characters. SCPI commands are not case sensitive.

PBZ_INTERFACE 19

Command Description in This Manual

In this manual, commands are described in the following manner.

References to command descriptions

CURR:PROT:OVER

Command [SOURce:]CURRent:PROTection[:LEVel]:OVER {<numeric>|MIN|MAX}[SOURce:]CURRent:PROTection[:LEVel]:OVER?

Parameter Value:

Unit: A

Response Returns the positive current activation point in <NR3> format.

-1 % to 110 % of the rated output current (The default value is 110 % of the rated output current.)

Commands that have these marks are affected when an *RST or *RCL command is sent. The settings for the command are changed to the values that are shown in the “Default State” section.

The commands are listed in the long form.The lowercase characters can be omitted.Sections that are enclosed in braces ([ ]) can also be omitted.

The selectable range is given.Optional symbols such as m and µ can also be used.

The unit for the value being set.The unit can be omitted.

Specify MIN to set the minimum value.

Specify MAX to set the maximum value.

The format of the value that is returned when a query is sent.

The parameters are listed.In this command, the parameter is numeric. In addition to specifying the desired value, you can specify the minimum or maximum value. * RCL* RST

Sets the positive OCP’s current activation point.

Item

Page

Command syntax 14

Parameters 17

Units 18

Default state 81

Queries 16

List of messages 87

List of errors 96

See

* RCL* RST

20 PBZ_INTERFACE

4 IEEE 488.2 Common Commands

*CLS

p. 72 Clears all event registers including the status byte, event status, and error queue.

Command *CLS

*ESE

p. 76 Sets the event status enable register that is counted by the event summary bit (ESB) of the status byte.

Command *ESE <NR1>*ESE?

Parameter Value: 0 to 255 An SCPI error (-222, “Data out of range”) occurs if the specified value is outside the range.

Example When *ESE 16 is transmitted, bit 4 of the event status enable register is set. Each time the execution error bit (bit 4) of the event status register is set, the summary bit (ESB) of the status byte is set.

Response Returns the value of the event status enable register in <NR1> format.

*ESR

p. 76 Queries the event status register. Registers that are read are cleared.

Command *ESR?

Response Returns the value of the event status register in <NR1> format and clears the register.

*IDN

Queries the model name, serial number, and firmware version of the PBZ.

Command *IDN?

Response The response to *IDN? is indicated below.

Example For a PBZ20-20 with serial number AB123456 and firmware version 1.00, *IDN? returns:KIKUSUI,PBZ20-20,AB123456,1.00.

See

See

See

PBZ_INTERFACE 21

IEEE 488.2 Common Commands

*OPC

IEEE 488.2-1992 Section 10.18

Sets the OPC bit (bit 0) of the event status register when all the commands that are in standby have been processed.

Command *OPC*OPC?

Response Returns “1” when all the commands that are in standby have been processed.

*OPT

Queries the options that are installed in the PBZ.

Command *OPT?

Response If the factory option LAN interface board is installed, "LAN" is returned. Returns “0” if no options are installed.

*PSC

IEEE 488.2-1992 Section 10.25

When the result of rounding the specified value is a number other than zero, it is interpreted as one, and this command sets the service request enable and event status enable registers to their initial values when the PBZ restarts.

Command *PSC <NR1>*PSC?

Parameter Value: -32767 to +32767

Response Returns “1” when the result of rounding the specified value is a number other than zero.

*RCL

Aborts measurement and loads the settings that have been saved to setup memory. This command performs the same function as the MEM:SET:RCL command.

p. 81 For the commands that are affected by *RCL, see " Default State".”

Command *RCL <NR1>

Parameter Value: 0 to 9 Memory number An SCPI error (-222, “Data out of range”) occurs if the specified value is outside the range.

*RST

Aborts measurement and initializes the PBZ to the factory default settings.

p. 81 For the commands that are affected by *RST, see " Default State".”

Command *RST

See

See

See

See

22 PBZ_INTERFACE


*SAV

Saves the current settings to setup memory. This command performs the same function as the MEM:SET:SAV command.

p. 81 For the commands that are affected by *RCL, see " Default State".”

Command *SAV <NR1>

Parameter Value: 0 to 9 Memory number An SCPI error (-222, “Data out of range”) occurs if the specified value is outside the range.

*SRE

Sets the service request enable register.The service request enable register can be used to select which summary messages in the status byte register will perform service requests.To clear the service request enable register, send *SRE 0. If the register is cleared, service requests cannot be generated by status information.

Command *SRE <NR1>*SRE?

Parameter Value: 0 to 255 An SCPI error (-222, “Data out of range”) occurs if the specified value is outside the range.

Example Sending *SRE 8 sets bit 3 of the service request enable register. Each time the summary bit (bit 3) of the QUEStionable status register in the status byte is set, a service request message is generated.

Response Returns the value of the service request enable register in <NR1> format.

*STB

p. 74 Queries the contents of the status byte register and the MSS (master summary status) message.The response is the same as serial polling only with the exception that the MSS message appears in place of the RQS message in bit 6.

Command *STB?

Response Returns the value of the status byte register and the MSS message (bit 6) in <NR1> format.

*TRG

IEEE 488.2-1992 Section 10.37

Trigger command.This is a substitute command for the IEEE 488.1 get message (Group Execute Trigger). If the PBZ is in a state in which it does not accept triggers, an SCPI error (-211, “Trigger ignored”) occurs.

Command *TRG

See

See

See

PBZ_INTERFACE 23


*TST

IEEE 488.2-1992 Section 10.38

Executes a self-test. You can query which error occurred by sending the SYST:ERR? command.

Command *TST?

Response Returns “0” if no errors are detected. Returns the error code if an error is detected.

*WAI

Prevents the PBZ from executing subsequent commands until all operations that are in standby have completed.

Command *WAI

See

24 PBZ_INTERFACE

5 Output Setting Commands

CV/CC Mode and Bipolar/Unipolar Mode

FUNC:MODE

Sets the CV/CC mode setting.

Command [SOURce:]FUNCtion:MODE {CC|CV}[SOURce:]FUNCtion:MODE?

Parameter Value: CC CC mode CV CV mode (default)

Response Returns the setting in <character> format in response to the FUNC:MODE? query.

FUNC:POL

Sets the bipolar/unipolar mode setting.

Command [SOURce:]FUNCtion:POLarity {BIPolar|UNIPolar}[SOURce:]FUNCtion:POLarity?

Parameter Value: BIPolar Bipolar mode (default) UNIPolar Unipolar mode

Response Returns the setting in <character> format in response to the FUNC:POL? query.

Selecting the Signal Source (Internal or External) and Setting the External Signal Source

FUNC:SOUR

Sets the signal source (internal, external, or both).

Command [SOURce:]FUNCtion:SOURce {INTernal|EXTernal|BOTH}[SOURce:]FUNCtion:SOURce?

Parameter Value: INTernal Internal signal source (default) EXTernal External signal source BOTH Internal signal source and external signal source are added (ADD)

Response Returns the setting in <character> format in response to the FUNC:SOUR? query.

* RCL* RST

* RCL* RST

* RCL* RST

PBZ_INTERFACE 25

Output Setting Commands

FUNC:EXT:TERM

Selects the external signal source terminal.

Command [SOURce:]FUNCtion:EXTernal:TERMinal {BNC|J1|BOTH}[SOURce:]FUNCtion:EXTernal:TERMinal?

Parameter Value: BNC BNC terminal (default) J1 J1 connector BOTH BNC terminal + J1 connector

Response Returns the setting in <character> format in response to the FUNC:EXT:TERM? query.

FUNC:EXT:CURR:GAIN FUNC:EXT:VOLT:GAIN

Sets the gain of the external signal source BNC terminal input.

Command [SOURce:]FUNCtion:EXTernal:CURRent:GAIN {<numeric>|MIN|MAX}[SOURce:]FUNCtion:EXTernal:VOLTage:GAIN {<numeric>|MIN|MAX}

Command [SOURce:]FUNCtion:EXTernal:CURRent:GAIN? [{MIN|MAX}][SOURce:]FUNCtion:EXTernal:VOLTage:GAIN? [{MIN|MAX}]

Parameter Value: PBZ20-20/ PBZ20-20A: 0 to 20 (CV or CC mode) PBZ40-10: 0 to 40 (CV mode), 0 to 10 (CC mode) PBZ60-6.7: 0 to 60 (CV mode), 0 to 6.7 (CC mode) PBZ80-5: 0 to 80 (CV mode), 0 to 5 (CC mode) (The default value is 0.)

Unit: A/V or V/V

Response Returns the gain in <NR3> format in response to the FUNC:EXT:CURR:GAIN? and FUNC:EXT:VOLT:GAIN? queries.

* RCL* RST

* RCL* RST

26 PBZ_INTERFACE


DC Signal Setting

VOLT CURR

Sets the DC signal voltage and current.

Command [SOURce:]VOLTage[:LEVel][:IMMediate][:AMPLitude] {<numeric>|MIN|MAX}

[SOURce:]CURRent[:LEVel][:IMMediate][:AMPLitude] {<numeric>|MIN|MAX}

Command [SOURce:]VOLTage[:LEVel][:IMMediate][:AMPLitude]? [{MIN|MAX}][SOURce:]CURRent[:LEVel][:IMMediate][:AMPLitude]? [{MIN|MAX}]

Parameter Value: 0 % to 105 % of the rated output (The default value is 0 % of the rated output.)Unit: V or A

Response Returns the voltage setting in <NR3> format in response to the VOLT? and CURR? queries.

VOLT:TRIG CURR:TRIG

Sets the DC signal voltage and current when software triggers are received.

Command [SOURce:]VOLTage[:LEVel]:TRIGgered[:AMPLitude] {<numeric>|MIN|MAX}

[SOURce:]CURRent[:LEVel]:TRIGgered[:AMPLitude] {<numeric>|MIN|MAX}

Command [SOURce:]VOLTage[:LEVel]:TRIGgered[:AMPLitude]? [{MIN|MAX}][SOURce:]CURRent[:LEVel]:TRIGgered[:AMPLitude]? [{MIN|MAX}]

Parameter Value: 0 % to 105 % of the rated outputUnit: V or A

Response Returns the setting in <NR3> format in response to the VOLT:TRIG? and CURR:TRIG? queries.

* RCL* RST

PBZ_INTERFACE 27


AC Signal Command

Setting the AC Signal On/Off State

AC:STAT

Sets the AC signal on/off state.

Command [SOURce:]AC:STATe {ON|OFF|1|0}[SOURce:]AC:STATe?

Parameter Value: ON (1) On OFF (0) Off (default)

Response Returns the AC signal on/off state in <NR1> format in response to the AC:STAT? query.

AC:STAT:TRIG

Sets the AC signal on/off state when software triggers are received.

Command [SOURce:]AC:STATe:TRIGgered {ON|OFF|1|0}[SOURce:]AC:STATe:TRIGgered?

Parameter Value: ON (1) On OFF (0) Off

Response Returns the AC signal on/off state in <NR1> format in response to the AC:STAT:TRIG? query.

Fixed Waveforms and User-defined Arbitrary Waveforms

FUNC

Selects the AC signal waveform.

Command [SOURce:]FUNCtion[:SHAPe][:IMMediate] {SINusoid|SQUare|TRIangle|USER[1]..USER16}

[SOURce:]FUNCtion[:SHAPe][:IMMediate]?

Parameter Value: SINusoid Sine wave(default) SQUare Square wave TRIangle Triangle wave USER[1] to USER16 User-defined arbitrary waveform (ARB1 to ARB16)

Response Returns the AC signal waveform type in <character> format in response to the FUNC? query.

* RCL* RST

* RCL* RST

28 PBZ_INTERFACE


FUNC:TRIG

Selects the AC signal waveform when software triggers are received. The settable ranges for the VOLT:TRIG, CURR:TRIG, VOLT:AC:TRIG, and CURR:AC:TRIG commands differ based on the FUNC:TRIG setting. When this command is received, the PBZ first checks the relationship between these settings. To ensure proper operation, send the FUNC:TRIG command first. When the FUNC:TRIG command is received, the PBZ immediately sets the VOLT:TRIG, CURR:TRIG, VOLT:AC:TRIG, and CURR:AC:TRIG values to the current values.

Command [SOURce:]FUNCtion[:SHAPe]:TRIGgered {SINusoid|SQUare|TRIangle|USER[1]..USER16}

[SOURce:]FUNCtion[:SHAPe]:TRIGgered?

Parameter Value: SINusoid Sine wave SQUare Square wave TRIangle Triangle wave USER[1] to USER16 User-defined arbitrary waveform

Response Returns the AC signal waveform type in <character> format.

USER{[1]|2|...|16}:TITL

Sets the user-defined arbitrary waveform’s title to a string of 15 characters in length. A space character(0x20) is inserted automatically in case of a string of less than 15 characters in length. The user-defined arbitrary waveforms are from USER1 to USER16. You can write USER1 as USER (omitting the “1”).

Command [SOURce:]USER{[1]|2|..|16}:TITLe <“string”>[SOURce:]USER{[1]|2|..|16}:TITLe?

Parameter Value: “string”

Example “My Waveform”

Response Returns the user-defined arbitrary waveform’s title in <“string”> format.

USER{[1]|2|...|16}:DATA:FORM:BORD

Sets the binary transmission data byte order of the user-defined arbitrary waveform. This command cannot be used with the RS232C interface.

Command [SOURce:]USER{[1]|2|..|16}:DATA:FORMat:BORDer {NORMal|SWAPped}

[SOURce:]USER{[1]|2|..|16}:DATA:FORMat:BORDer?

Parameter Value: NORMal Big endian (most significant byte first) SWAPped Little endian (least significant byte first)

Response Returns the binary transmission data byte order of the user-defined arbitrary waveform in <character> format.

PBZ_INTERFACE 29


USER{[1]|2|...|16}:DATA

Sets the user-defined arbitrary waveform pattern. The user-defined arbitrary waveforms are from USER1 to USER16. You can write USER1 as USER (omitting the “1”). This command cannot be used with the RS232C interface or LAN interface.To use the RS232C or LAN interface to set a user-defined arbitrary waveform pattern, use USER{[1]|2|...|16}:DATA:VAL.

Command [SOURce:]USER{[1]|2|..|16}:DATA <arbitrary block data>[SOURce:]USER{[1]|2|..|16}:DATA?

Parameter Value: Arbitrary block data (in binary block format)

Response Returns the user-defined arbitrary waveform pattern in <arbitrary block data> format.

Binary block format data

Waveform data is represented as integer values that are composed of 2 bytes (16 bits) of binary data. Therefore, the total number of bytes used for a waveform’s data is the number of data points in the waveform times two. This number is always even. For example, if the number of waveform data points is 1024, the total number of bytes in the waveform data is 2048.

7FFF (H) 32767

8000 (H) -32768

USER2:DATA #420487FFF8000...7FFF...7FFF8000Example

#42048

Data points 0 1024

Data points 0 1024

Signed 16-bit data

7FFF8000...7FFF...7FFF8000

2 bytes 2 bytes

(2048 bytes)

Number of bytes that follow

Number of digits that follow (these represent the number of bytes)

Start of the data block

FF7F

7FFF

Order setting for the pairs of bytes for each data point

NORM:

SWAP:

USER2:DATA:FORM:BORD

30 PBZ_INTERFACE


USER{[1]|2|...|16}:DATA:VAL

Sets the waveform data relative to the waveform peak value for any of 1024 divisions of one period of a user-defined arbitrary waveform. These waveform divisions are referred to as “addresses.” The user-defined arbitrary waveforms are from USER1 to USER16. You can write USER1 as USER (omitting the “1”).

Command [SOURce:]USER{[1]|2|..|16}:DATA:VALue <addr_NR1>,<data_NR1>[SOURce:]USER{[1]|2|..|16}:DATA:VALue? <addr_NR1>

Parameter <addr_NR1>AddressValue: 0 to 1 023

<data_NR1>Waveform dataValue: -32 768 to +32 767

Example USER10:DATA:VAL 0,32767 Sets address 0 of the user-defined arbitrary waveform pattern to 32767. To enter data for a square wave, set addresses 0 to 511 to +32767, and set addresses 512 to 1023 to -32768.

Response Returns the value at an address in a user-defined arbitrary waveform pattern in <NR1> format.

Signal Amplitude, Frequency, and Start Phase, and Square Wave Duty Cycle

VOLT:AC

Sets the AC signal voltage.

Command [SOURce:]VOLTage:AC[:IMMediate][:AMPLitude] {<numeric>|MIN|MAX}

[SOURce:]VOLTage:AC[:IMMediate][:AMPLitude]? [{MIN|MAX}]

Parameter Value: 0 % to 105 % of the rated output voltage (The default value is 0 % of the rated output voltage.)

Unit: VPP

Response Returns the setting in <NR3> format in response to the VOLT:AC? query.

CURR:AC

Sets the AC signal current.

Command [SOURce:]CURRent:AC[:IMMediate][:AMPLitude] {<numeric>|MIN|MAX}

[SOURce:]CURRent:AC[:IMMediate][:AMPLitude]? [{MIN|MAX}]

Parameter Value: 0 % to 105 % of the rated output (The default value is 0 % of the rated output current.)

Unit: APP

Response Returns the setting in <NR3> format in response to the CURR:AC? query.

* RCL* RST

* RCL* RST

PBZ_INTERFACE 31


VOLT:AC:TRIG CURR:AC:TRIG

Sets the AC signal voltage and current when software triggers are received.

Command [SOURce:]VOLTage:AC:TRIGgered[:AMPLitude]{<numeric>|MIN|MAX}[SOURce:]CURRent:AC:TRIGgered[:AMPLitude]{<numeric>|MIN|MAX}

Command [SOURce:]VOLTage:AC:TRIGgered[:AMPLitude]? [{MIN|MAX}][SOURce:]CURRent:AC:TRIGgered[:AMPLitude]? [{MIN|MAX}]

Parameter Value: 0 % to 105 % of the rated outputUnit: VPP or APP

Response Returns the setting in <NR3> format in response to the VOLT:AC:TRIG? and CURR:AC:TRIG? queries.

FREQ

Sets the AC signal frequency.

Command [SOURce:]FREQuency[:IMMediate] {<numeric>|MIN|MAX}[SOURce:]FREQuency[:IMMediate]? [{MIN|MAX}]

Parameter Value: PBZ20-20/PBZ40-10/PBZ60-6.7/PBZ80-5: +1.0E-02 Hz to +1.0E+05 Hz (The default value is 1 kHz.) Maximum CV mode: +1.0E+05 (100 kHz)

CC mode: +1.0E+05 (100 kHz)

PBZ20-20A: +1.0E-02 Hz to +2.0E+05 Hz (The default value is 1 kHz.) Maximum CV mode: +2.0E+05 (200 kHz)

CC mode: +2.0E+05 (200 kHz)Unit: HZ

Response Returns the setting in <NR3> format in response to the FREQ? query.

FREQ:TRIG

Sets the AC signal frequency when software triggers are received.

Command [SOURce:]FREQuency:TRIGgered{<numeric>|MIN|MAX}[SOURce:]FREQuency:TRIGgered? [{MIN|MAX}]

Parameter Value: PBZ20-20/PBZ40-10/PBZ60-6.7/PBZ80-5: +1.0E-02 Hz to +1.0E+05 Hz Maximum CV mode: +1.0E+05 (100 kHz)

CC mode: +1.0E+05 (100 kHz)

PBZ20-20A: +1.0E-02 Hz to +2.0E+05 Hz Maximum CV mode: +2.0E+05 (200 kHz)


Response Returns the setting in <NR3> format in response to the FREQ:TRIG? query.

* RCL* RST

32 PBZ_INTERFACE


PHAS

Sets the AC signal start phase angle.

Command [SOURce:]PHASe {<numeric>|MIN|MAX},{ON|OFF|1|0}[SOURce:]PHASe?

Parameter Value: 0 to 359 (The default value is 0.)Unit: DEG (degrees)

Parameter Value: ON (1) Set the start phase angle (default) OFF (0) Do not set the start phase angle

Response Returns the start phase angle setting and whether the start phase angle is set or not in <NR3>,<NR1> format in response to the PHAS? query.

SQU:DCYC

Sets the square wave signal duty cycle.

Command [SOURce:]SQUare:DCYCle {<numeric>|MIN|MAX}[SOURce:]SQUare:DCYCle? [{MIN|MAX}]

Parameter Value: 0.1 % to 99.9 % (The default value is 50.0 %.) The settable range depends on the settings of the AC signal frequency.

Unit: PCT

Response Returns the setting in <NR3> format in response to the SQU:DCYC? query.

Frequency Sweep

SWE:STATTurns the AC signal frequency sweep on and off.

Command [SOURce:]SWEep:STATe {ON|OFF|1|0}[SOURce:]SWEep:STATe?

Parameter Value: ON (1) Frequency sweeps are executed. OFF (0) Frequency sweeps are not executed (default).

Response Returns whether frequency sweeps are on or off in <NR1> format in response to the SWE:STAT? query.

* RCL* RST

* RCL* RST

* RCL* RST

PBZ_INTERFACE 33


SWE:SPAC

Sets the AC signal frequency sweep mode.

Command [SOURce:]SWEep:SPACing {LOGarithmic|LINear}[SOURce:]SWEep:SPACing?

Parameter Value: LOGarithmic Logarithmic sweep (default) LINear Linear sweep

Response Returns the AC signal frequency sweep mode in <character> format in response to the SWE:SPAC? query.

SWE:TIMESets the AC signal frequency sweep time.

Command [SOURce:]SWEep:TIME {<numeric>|MIN|MAX}[SOURce:]SWEep:TIME? [{MIN|MAX}]

Parameter Value: 0.0001 to 1000 (The default value is 1.)Unit: S

Response Returns the sweep time in <NR3> format in response to the SWE:TIME? query.

SWE:FREQ:STAR SWE:FREQ:STOP

Sets the AC signal frequency sweep start and stop frequencies.

Command [SOURce:]SWEep:FREQuency:STARt[:IMMediate] {<numeric>|MIN|MAX}

[SOURce:]SWEep:FREQuency:STOP[:IMMediate] {<numeric>|MIN|MAX}

Command [SOURce:]SWEep:FREQuency:STARt[:IMMediate]? [{MIN|MAX}][SOURce:]SWEep:FREQuency:STOP[:IMMediate]? [{MIN|MAX}]

Parameter Value: PBZ20-20/PBZ40-10/PBZ60-6.7/PBZ80-5: CV mode +1.0E-2 Hz to +1.0E+05 Hz CC mode +1.0E-2 Hz to +1.0E+05 Hz The default start frequency is 100 Hz. The default stop frequency is 1 kHz.

PBZ20-20A: CV mode +1.0E-2 Hz to +2.0E+05 Hz CC mode +1.0E-2 Hz to +2.0E+05 Hz The default start frequency is 100 Hz. The default stop frequency is 1 kHz.

Unit: HZ

Response Returns the start or stop frequency in <NR3> format in response to the SWE:FREQ:STAR? or SWE:FREQ:STOP? query.

* RCL* RST

* RCL* RST

* RCL* RST

34 PBZ_INTERFACE


MARK

Sets the type of output that the TRIG OUT terminal generates. Select MARKER signals or SYNC signals.The setting of the type of the TRIG OUT terminalt output is valid when trigger signal output setting is on.

Command [SOURce:]MARKer {ON|OFF|1|0}[SOURce:]MARKer?

Parameter Value: ON (1) MARKER signals OFF (0) SYNC signals (default)

Response Returns the type of output that the TRIG OUT terminal generates in <NR1> format in response to the MARK? query.

MARK:FPOSets the marker frequency of the AC signal frequency sweep.

Command [SOURce:]MARKer:FPOint {<numeric>|MIN|MAX}[SOURce:]MARKer:FPOint? [{MIN|MAX}]

Parameter Value: PBZ20-20/PBZ40-10/PBZ60-6.7/PBZ80-5: CV mode +1.0E-2 Hz to +1.0E+05 Hz (The default value is 500 Hz.) CC mode +1.0E-2 Hz to +1.0E+05 Hz (The default value is 500 Hz.) The settable frequency range is greater than the start frequency and less than the stop frequency. MIN is the sweep start or stop frequency, whichever is lower. MAX is the sweep start or stop frequency, whichever is higher.

PBZ20-20A: CV mode +1.0E-2 Hz to +2.0E+05 Hz (The default value is 500 Hz.) CC mode +1.0E-2 Hz to +2.0E+05 Hz (The default value is 500 Hz.) The settable frequency range is greater than the start frequency and less than the stop frequency. MIN is the sweep start or stop frequency, whichever is lower. MAX is the sweep start or stop frequency, whichever is higher.

Unit: HZ

Response Returns the marker frequency in <NR3> format in response to the MARK:FPO? query.

* RCL* RST

* RCL* RST

PBZ_INTERFACE 35


Collective Settings (Waveform, Frequency, Signal Amplitude, and DC Signal)

APPL:DC APPL:SIN APPL:SQU APPL:TRI APPL:USER{[1]|2|...|16} APPL

Collectively sets the signal type, AC signal frequency, AC signal amplitude, and DC signal setting.

Command DC signal. AC signal frequency and AC signal amplitude are void.[SOURce:]APPLy:DC <freq_numeric>,<ac_numeric>,<dc_numeric>

Command AC signal (sine wave)[SOURce:]APPLy:SIN

<freq_numeric>[,<ac_numeric>[,<dc_numeric>]]

Command AC signal (square wave)[SOURce:]APPLy:SQU


Command AC signal (triangular wave)[SOURce:]APPLy:TRI


Command Arbitrary waveform (USER{[1]|2|...|16})[SOURce:]APPLy:USER{[1]|2|..|16} <freq_numeric>[,<ac_numeric>

[,<dc_numeric>]]

Command [SOURce:]APPLy?

Parameter <freq_numeric>　AC signal frequencyValue: PBZ20-20/PBZ40-10/PBZ60-6.7/PBZ80-5:

CV mode +1.0E-2 Hz to +1.0E+05 Hz (AC signal) CC mode +1.0E-2 Hz to +1.0E+05 Hz (AC signal)

PBZ20-20A: CV mode +1.0E-2 Hz to +2.0E+05 Hz (AC signal) CC mode +1.0E-2 Hz to +2.0E+05 Hz (AC signal)

Unit: HZ

Parameter <ac_numeric>　AC signal amplitudeValue: 0 % to 105 % of the rated output (AC signal)

Unit: VPP or APP

Parameter <dc_numeric>　DC signal settingValue: 0 % to 105 % of the rated output (DC signal)

Unit: V or A When you are setting the DC signal, frequency and amplitude settings for the AC signal are invalid.

Response Returns the signal type (DC, SIN, SQU, TRI, USER{1|2|...|16}), AC signal frequency, AC signal amplitude, and DC signal setting in the following order in response to APPLy?.<character>,<NR3>,<NR3>,<NR3>

* RCL* RST

36 PBZ_INTERFACE


Amplifier Responses

CURR:RESP VOLT:RESP

Sets the amplifier’s response. Set this separately for CV mode and CC mode.

Command [SOURce:]CURRent:RESPonse {<numeric>|MIN|MAX}[SOURce:]VOLTage:RESPonse {<numeric>|MIN|MAX}

Command [SOURce:]CURRent:RESPonse? [{MIN|MAX}][SOURce:]VOLTage:RESPonse? [{MIN|MAX}]

Parameter Value: CC mode (PBZ20-20/ PBZ60-6.7/ PBZ80-5) 35 US 35 µs (default) 100 US 100 µs 350 US 350 µs 1 MS 1 ms

Parameter Value: CC mode (PBZ40-10) 70 US 70 µs (default) 100 US 100 µs 350 US 350 µs 1 MS 1 ms

Parameter Value: CV mode (PBZ models) 3.5 US 3.5 µs (default) 10 US 10 µs 35 US 35 µs 100 US 100 µs

Unit: US and MS

Response Returns the response in <NR3> format in response to the CURR:RESP? and VOLT:RESP? queries.

Output, Trigger Signals, and Screen Contrast

Turning Output On and Off

OUTP

Turns output on and off.

Command OUTPut[:STATe][:IMMediate] {ON|OFF|1|0}OUTPut[:STATe][:IMMediate]?

Parameter Value: ON (1) Turns output on OFF (0) Turns output off (default)

Response Returns whether output is on or off in <NR1> format in response to the OUTP? query.

* RCL* RST

* RCL* RST

PBZ_INTERFACE 37


OUTP:TRIG

Turns output on and off when software triggers are received.

Command OUTPut[:STATe]:TRIGgered {ON|OFF|1|0}OUTPut[:STATe]:TRIGgered?

Parameter Value: ON (1) Turns output on OFF (0) Turns output off

Response Returns whether output is on or off in <NR1> format in response to the OUTP:TRIG? query.

OUTP:PON:STAT

Sets whether output turns on or off when the PBZ turns on.

Command OUTPut:PON:STATe {RST|AUTO}OUTPut:PON:STATe?

Parameter Value: RST Output is off when the PBZ turns on (default). AUTO Output turns on when the PBZ turns on.

Response Returns whether output turns on or off when the PBZ turns on in <character> format in response to the OUTP:PON:STAT? query.

OUTP:EXT

Sets the polarity of the external control signal that is used to turn output on.

Command OUTPut:EXTernal {NORMal|INVerted}OUTPut:EXTernal?

Parameter Value: NORMal A high level signal turns the output on (default). INVerted A low level signal turns the output on.

Response Returns the polarity of the external control signal in <character> format in response to the OUTP:EXT? query.

Option Output

OUTP:PORT

Turns signal output from the J1 connector and option terminal on and off.

Command OUTPut:PORT {ON|OFF|1|0}OUTPut:PORT?

Parameter Value: ON (1) Generate signal output OFF (0) Do not generate signal output (default)

Response Returns whether output is on or off in <NR1> format in response to the OUTP:PORT? query.

* RCL* RST

* RCL* RST

* RCL* RST

38 PBZ_INTERFACE


Trigger Signals (TRIG IN and TRIG OUT)

OUTP:TRIG:STAT

Turns trigger signal output (TRIG OUT) on and off. When trigger signal output setting is on, the TRIG OUT terminal can transmit MARKER or SYNC signals.

Command OUTPut:TRIGger:STATe {ON|OFF|1|0}OUTPut:TRIGger:STATe?

Parameter Value: ON (1) Generate trigger signal output OFF (0) Do not generate trigger signal output (default)

Response Returns whether trigger signal output (TRIG OUT) is on or off in <NR1> format in response to the OUTP:TRIG:STAT? query.

OUTP:TRIG:POL

Sets the polarity of the trigger signal output (TRIG OUT).

Command OUTPut:TRIGger:POLarity {POSitive|NEGative}OUTPut:TRIGger:POLarity?

Parameter Value: POSitive Rising (default) NEGative Falling

Response Returns the polarity of the trigger signal output (TRIG OUT) in <character> format in response to the OUTP:TRIG:POL? query.

INP:TRIG:POL

Sets the polarity of the trigger signal input (TRIG IN).

Command INPut:TRIGger:POLarity {POSitive|NEGative}INPut:TRIGger:POLarity?

Parameter Value: POSitive High level (default) NEGative Low level

Response Returns the polarity of the trigger signal input (TRIG IN) in <character> format in response to the INP:TRIG:POL? query.

Screen Contrast

DISP:CONT

Sets the screen contrast.

Command DISPlay:CONTrast {<numeric>|MIN|MAX}DISPlay:CONTrast? [{MIN|MAX}]

Parameter Value: 0.0 to 1.0 (The default value is 0.7.)Unit: None

Response Returns the screen contrast in <NR3> format in response to the DISP:CONT? query.

* RCL* RST

* RCL* RST

* RCL* RST

* RCL* RST

PBZ_INTERFACE 39

6 Protection Features Commands

Mode

CURR:PROT:STAT VOLT:PROT:STAT

Sets the mode (I/V-LIMIT or OCP/OVP) of the overvoltage and overcurrent protection features.

Command [SOURce:]CURRent:PROTection:STATe {LIMit|TRIP}[SOURce:]VOLTage:PROTection:STATe {LIMit|TRIP}

Command [SOURce:]CURRent:PROTection:STATe?[SOURce:]VOLTage:PROTection:STATe?

Parameter Value: LIMit Voltage or current limit is used.(default) TRIP OVP/OCP is used.

Returns the mode in <character> format in response to the {CURR|VOLT}:PROT:STAT? query.

Activation points (OCP/OVP)

Use SYST:CONF:BTR:PROT to set the protection operation to perform (power off or output off) when OCP or OVP is activated.

CURR:PROT:OVER VOLT:PROT:OVER

Sets the value of the positive OCP or OVP trip point for the current or voltage.

Command [SOURce:]CURRent:PROTection[:LEVel]:OVER {<numeric>|MIN|MAX}[SOURce:]VOLTage:PROTection[:LEVel]:OVER {<numeric>|MIN|MAX}

Command [SOURce:]CURRent:PROTection[:LEVel]:OVER? [{MIN|MAX}][SOURce:]VOLTage:PROTection[:LEVel]:OVER? [{MIN|MAX}]

Parameter Value: +1 % to +110 % of the rated value (The default value is +110 % of the rated value.)Unit: A or V

Response Returns the setting in <NR3> format in response to the {CURR|VOLT}:PROT:OVER? query.

* RCL* RST

* RCL* RST

40 PBZ_INTERFACE

Protection Features Commands

CURR:PROT:UND VOLT:PROT:UND

Sets the value of the negative OCP or OVP trip point for the current or voltage.

Command [SOURce:]CURRent:PROTection[:LEVel]:UNDer {<numeric>|MIN|MAX}[SOURce:]VOLTage:PROTection[:LEVel]:UNDer {<numeric>|MIN|MAX}

Command [SOURce:]CURRent:PROTection[:LEVel]:UNDer? [{MIN|MAX}][SOURce:]VOLTage:PROTection[:LEVel]:UNDer? [{MIN|MAX}]

Parameter Value: -110 % to -1 % of the rated value (The default value is -110 % of the rated value.)Unit: A or V

Response Returns the setting in <NR3> format in response to the {CURR|VOLT}:PROT:UND? query.

* RCL* RST

PBZ_INTERFACE 41


Activation points (I.LIM/ V.LIM)

CURR:LIM:UPP VOLT:LIM:UPP

Sets the value of the positive I.LIM or V.LIM trip point for the current or voltage.

Command [SOURce:]CURRent:LIMit[:LEVel]:UPPer {<numeric>|MIN|MAX}[SOURce:]VOLTage:LIMit[:LEVel]:UPPer {<numeric>|MIN|MAX}

Command [SOURce:]CURRent:LIMit[:LEVel]:UPPer? [{MIN|MAX}][SOURce:]VOLTage:LIMit[:LEVel]:UPPer? [{MIN|MAX}]

Parameter Value: +1 % of rated value ≤ +I.LIM ≤ +110 % of the rated value -110 % of rated value ≤ -V.LIM ≤ +V.LIM ≤ +110 % of the rated value (The default value is +110 % of the rated value.)

Unit: A or V

Response Returns the setting in <NR3> format in response to the {CURR|VOLT}:LIM:UPP? query.

CURR:LIM:LOW VOLT:LIM:LOW

Sets the value of the negative I.LIM or V.LIM trip point for the current or voltage.

Command [SOURce:]CURRent:LIMit[:LEVel]:LOWer {<numeric>|MIN|MAX}[SOURce:]VOLTage:LIMit[:LEVel]:LOWer {<numeric>|MIN|MAX}

Command [SOURce:]CURRent:LIMit[:LEVel]:LOWer? [{MIN|MAX}][SOURce:]VOLTage:LIMit[:LEVel]:LOWer? [{MIN|MAX}]

Parameter Value: -110 % of rated value ≤ -I.LIM ≤ -1 % of the rated value -110 % of rated value ≤ -V.LIM ≤ +V.LIM ≤ +110 % of the rated value (The default value is -110 % of the rated value.)

Unit: A or V

Response Returns the setting in <NR3> format in response to the {CURR|VOLT}:LIM:LOW? query.

* RCL* RST

* RCL* RST

42 PBZ_INTERFACE


Mode and activation points (legacy command)

The following commands were used up to firmware version 2.19. When creating a new program, use the commands listed under the aforementioned OVP or OCP trip point or V.LIM or I.LIM trip point.

The CURR:PROT:UPP and CURR:PROT:LOW commands apply to the protection mode (OCP or current limit) selected with CURR:PROT:STAT. The VOLT:PROT:UPP and VOLT:PROT:LOW commands apply to the protection mode (OVP or voltage limit) selected with VOLT:PROT:STAT. To use a program that you were using for firmware version 2.19 or earlier, check that the protection mode is set before the trip points are set.

Use SYST:CONF:BTR:PROT to set the protection operation to perform (power off or output off) when OVP or OCP is activated.

CURR:PROT:UPP

If CURR:PROT:STAT LIM is specified, this command sets the value of the positive I.LIM trip point.If CURR:PROT:STAT TRIP is specified, this command sets the value of the positive OCP trip point.

Command [SOURce:]CURRent:PROTection[:LEVel]:UPPer {<numeric>|MIN|MAX}[SOURce:]CURRent:PROTection[:LEVel]:UPPer? [{MIN|MAX}]

Parameter Value: +1 % to +110 % of the rated value (The default value is +110 % of the rated value.)Unit: A

Response Returns the setting in <NR3> format in response to the CURR:PROT:UPP? query.

VOLT:PROT:UPP

If VOLT:PROT:STAT LIM is specified, this command sets the value of the positive V.LIM trip point.If VOLT:PROT:STAT TRIP is specified, this command sets the value of the positive OVP trip point.

Command [SOURce:]VOLTage:PROTection[:LEVel]:UPPer {<numeric>|MIN|MAX}[SOURce:]VOLTage:PROTection[:LEVel]:UPPer? [{MIN|MAX}]

Parameter Value: -110 % of rated value ≤ -V.LIM ≤ +V.LIM ≤ +110 % of the rated value% (when VOLT:PROT:STAT LIM is specified) +1 % to +110 % of the rated value (when VOLT:PROT:STAT TRIP is specified) (The default value is +110 % of the rated value.)

Unit: V

Response Returns the setting in <NR3> format in response to the VOLT:PROT:UPP? query.

CURR:PROT:UPP

+I.LIM

OCPIf CURR:PROT:STAT TRIP is specified, the command sets OCP.

If CURR:PROT:STAT LIM is specified, the command sets +I.LIM.

CURR:PROT:UPP operation example

* RCL* RST

* RCL* RST

PBZ_INTERFACE 43


CURR:PROT:LOW

If CURR:PROT:STAT LIM is specified, this command sets the value of the negative I.LIM trip point.If CURR:PROT:STAT TRIP is specified, this command sets the value of the negative OCP trip point.

Command [SOURce:]CURRent:PROTection[:LEVel]:LOWer {<numeric>|MIN|MAX}[SOURce:]CURRent:PROTection[:LEVel]:LOWer? [{MIN|MAX}]

Parameter Value: -110 % to -1 % of the rated value (The default value is -110 % of the rated value.)Unit: A

Response Returns the setting in <NR3> format in response to the CURR:PROT:LOW? query.

VOLT:PROT:LOW

If VOLT:PROT:STAT LIM is specified, this command sets the value of the negative V.LIM trip point.If VOLT:PROT:STAT TRIP is specified, this command sets the value of the negative OVP trip point.

Command [SOURce:]VOLTage:PROTection[:LEVel]:LOWer {<numeric>|MIN|MAX}[SOURce:]VOLTage:PROTection[:LEVel]:LOWer? [{MIN|MAX}]

Parameter Value: -110 % of rated value ≤ -V.LIM ≤ +V.LIM ≤ +110 % of the rated value% (when VOLT:PROT:STAT LIM is specified) -110 % to -1 % of the rated value (when VOLT:PROT:STAT TRIP is specified) (The default value is -110 % of the rated value.)

Unit: V

Response Returns the setting in <NR3> format in response to the VOLT:PROT:LOW? query.

Clearing Alarms

OUTP:PROT:CLE

Clears alarms.

Command OUTPut:PROTection:CLEar

* RCL* RST

* RCL* RST

44 PBZ_INTERFACE

7 Measurement Function Commands

SENS:FUNC

Sets the measurement function.

Command SENSe:FUNCtion {DC|AC|DCAC|PEAK}SENSe:FUNCtion?

Parameter Value: DC DC (default) AC AC RMS DCAC DC + AC RMS PEAK DC + the peak AC value

Response Returns the measurement function in <character> format in response to the SENS:FUNC? query.

SENS:APERSets the measurement time.

Command SENSe:APERture {<numeric>|MIN|MAX}SENSe:APERture? [{MIN|MAX}]

Parameter Value: 0.0001 to 3600 (The default value is 0.1.)Unit: S

Response Returns the measurement time in <NR3> format in response to the SENS:APER? query.

SENS:TRIG:SOURSets the measurement start trigger source.

Command SENSe:TRIGger:SOURce {AUTO|INTernal|EXTPOS|EXTNEG}SENSe:TRIGger:SOURce?

Parameter Value: AUTO Start measuring automatically (default). INTernal Start measuring whenever a setting is changed. EXTPOS Start measuring when a rising edge is applied to the TRIG IN

terminal. EXTNEG Start measuring when a falling edge is applied to the TRIG IN

terminal.

Response Returns the measurement start trigger source in <character> format in response to the SENS:TRIG:SOUR? query.

* RCL* RST

* RCL* RST

* RCL* RST

PBZ_INTERFACE 45

Measurement Function Commands

SENS:TRIG:DEL

Sets the trigger delay.

Command SENSe:TRIGger:DELay {<numeric>|MIN|MAX}SENSe:TRIGger:DELay? [{MIN|MAX}]

Parameter Value: 0.000 00 to 3 600 (The default value is 0.000 00)Unit: S

Response Returns the delay time in <NR3> format in response to the SENS:TRIG:DEL? query.

Trigger Function

The PBZ has the following four trigger functions.• SEQuence1 (TRANsient)

Specify FUNCtion, FREQuency, CURRent (DC and AC), and VOLTage (DC and AC) settings in advance, and use trigger timing to set them.

• SEQuence2 (OUTPut)Specify OUTPUT ON/OFF settings in advance, and use trigger timing to set them.

• SEQuence3 (ACQuire)Use trigger timing to start measuring or query the measured values.

• SEQuence4 (PROGram)Use trigger timing to carry out PROGram or SCRipt execution. You have to specify the execution conditions in advance.

SEQuence1 (TRANsient)

The following table shows items that you can use trigger timing to set (<transient_item>). You can set the items immediately after a trigger occurs or wait for a software trigger and then set the items.

� CV mode

� CC mode

* RCL* RST

<transient_item> Description

Page

[SOURce:]VOLTage[:LEVel]:TRIGgered[:AMPLitude] DC signal voltage 26

[SOURce:]VOLTage:AC:TRIGgered[:AMPLitude] AC signal voltage 31


Page

[SOURce:]CURRent[:LEVel]:TRIGgered[:AMPLitude] DC signal current 26

[SOURce:]CURRent:AC:TRIGgered[:AMPLitude] AC signal current 31

See

See

46 PBZ_INTERFACE


� CV mode and CC mode

INIT INIT:NAME TRAN

Starts the TRANsient trigger function.

Command INITiate[:IMMediate][:SEQuence[1]]INITiate[:IMMediate]:NAME TRANsient

TRIG TRIG:TRAN

Executes a software trigger for the SEQuence1 (TRANsient) group.

Command TRIGger[:SEQuence[1]][:IMMediate]TRIGger:TRANsient[:IMMediate]

TRIG:SOUR TRIG:TRAN:SOUR

Sets an applicable trigger source for the SEQuence1 (TRANsient) group.

Command TRIGger[:SEQuence[1]]:SOURce {BUS|IMMediate}TRIGger[:SEQuence[1]]:SOURce?

Command TRIGger:TRANsient:SOURce {BUS|IMMediate}TRIGger:TRANsient:SOURce?

Parameter Value: BUS Software trigger Wait for a *TRG or IEEE 488.1 get (Group Execute Trigger) command, and then begin execution.

IMMediate Immediately begin execution (default)

Response Returns the current trigger source setting in <character> format.


Page

[SOURce:]AC:STAT:TRIGgered AC signal: on/off 27

[SOURce:]FUNCtion[:SHAPe]:TRIGgered AC signal waveform 28

[SOURce:]FREQuency:TRIGgered AC signal frequency 31

See

* RCL* RST

PBZ_INTERFACE 47


SEQuence2 (OUTPut)

The following table shows the item that you can use trigger timing to set (<output_item>). You can set the item immediately after a trigger occurs or wait for a software trigger and then set the item.

INIT:SEQ2 INIT:NAME OUTP

Starts the OUTPut trigger function.

Command INITiate[:IMMediate]:SEQuence2INITiate[:IMMediate]:NAME OUTPut

TRIG:SEQ2 TRIG:OUTP

Executes a software trigger for the SEQuence2 (OUTPut) group.

Command TRIGger:SEQuence2[:IMMediate]TRIGger:OUTPut[:IMMediate]

TRIG:SEQ2:SOUR TRIG:OUTP:SOUR

Sets an applicable trigger source for the SEQuence2 (OUTPut) group.

Command TRIGger:SEQuence2:SOURce {BUS|IMMediate}TRIGger:SEQuence2:SOURce?

Command TRIGger:OUTPut:SOURce {BUS|IMMediate}TRIGger:OUTPut:SOURce?


IMMediate Immediately begin execution (default)


<output_item> Description

Page

OUTput[:STATe]:TRIGgered Output: on/off 37

See

* RCL* RST

48 PBZ_INTERFACE


TRIG:SEQ2:SST:RISE TRIG:OUTP:SST:RISE

Sets the soft start time for the SEQuence2 (OUTPut) group.

Command TRIGger:SEQuence2:SSTart:RISE {<numeric>|MIN|MAX}TRIGger:SEQuence2:SSTart:RISE? [{MIN|MAX}]

Command TRIGger:OUTPut:SSTart:RISE {<numeric>|MIN|MAX}TRIGger:OUTPut:SSTart:RISE? [{MIN|MAX}]


Response Returns the soft start time in <NR3> format.

TRIG:SEQ2:SST:FALL TRIG:OUTP:SST:FALL

Sets the soft stop time for the SEQuence2 (OUTPut) group.

Command TRIGger:SEQuence2:SSTart:FALL {<numeric>|MIN|MAX}TRIGger:SEQuence2:SSTart:FALL? [{MIN|MAX}]

Command TRIGger:OUTPut:SSTart:FALL {<numeric>|MIN|MAX}TRIGger:OUTPut:SSTart:FALL? [{MIN|MAX}]


Response Returns the soft stop time in <NR3> format.

* RCL* RST

* RCL* RST

PBZ_INTERFACE 49


SEQuence3 (ACQuire)

The following table shows items that you can use trigger timing to measure (<meas_item>). You can measure the items immediately after a trigger occurs or wait for a software trigger and then measure the items.

The following table shows the different measurement operations that are available (FETC, READ, and MEAS).READ and MEASure operate exactly the same, as they are aliases.

FETC:<meas_item>Queries the measured value that is specified by <meas_item> without starting a new measurement.

Command FETCh[:SCALar]:<meas_item>?

Response Returns the measured value in <NR3> (number of digits to the right of the decimal is 5) format.

READ:<meas_item> MEAS:<meas_item>

Starts a new measurement, and queries the measured value that is specified by <meas_item>.

Command READ[:SCALar]:<meas_item>?MEASure[:SCALar]:<meas_item>?

Response Returns the measured value in <NR3> (number of digits to the right of the decimal is 5) format.

<meas_item> Measurement description

Page

VOLTage[:DC] DC voltage 26

VOLTage:AC AC voltage 30

VOLTage:{MINimum | MAXimum} Peak voltage, minimum, and maximum –

CURRent[:DC] DC current 26

CURRent:AC AC current 30

CURRent:{MINimum | MAXimum} Peak current, minimum, and maximum –

Measurement operation and command syntax Measurement operation description

:FETCh[:SCALar]:<meas_item>? Query the measured value without starting a new measurement.

:READ[:SCALar]:<meas_item>?:MEASure[:SCALar]:<meas_item>?

Start a new measurement, and query the measured value.

See

50 PBZ_INTERFACE


INIT:SEQ3 INIT:NAME ACQ

Starts the ACQuire trigger function. When an INIT command is sent, the measured value that is currently saved is deleted and invalidated. If you send a FETC? query immediately after you send an INIT command, the PBZ returns the measured value after it completes the measurement.

Command INITiate[:IMMediate]:SEQuence3INITiate[:IMMediate]:NAME ACQuire

TRIG:SEQ3 TRIG:ACQ

Executes a software trigger for the SEQuence3 (ACQuire) group.

Command TRIGger:SEQuence3[:IMMediate]TRIGger:ACQuire[:IMMediate]

TRIG:SEQ3:SOUR TRIG:ACQ:SOUR

Sets an applicable trigger source for the SEQuence3 (ACQuire) group.

Command TRIGger:SEQuence3:SOURce {BUS|IMMediate}TRIGger:SEQuence3:SOURce?

Command TRIGger:ACQuire:SOURce {BUS|IMMediate}TRIGger:ACQuire:SOURce?

Parameter Value: BUS Software trigger Wait for a *TRG or IEEE 488.1 get (Group Execute Trigger) command, and then begin measuring.

IMMediate Immediately begin measuring (default)


* RCL* RST

PBZ_INTERFACE 51


SEQuence4 (PROGram)

This trigger function is used to carry out PROGram or SCRipt execution. You have to specify the execution conditions in advance. You can execute the program or script immediately after a trigger occurs or wait for a software trigger and then carry out execution.

INIT:SEQ4 INIT:NAME PROG

Starts the PROGram trigger function.

Command INITiate[:IMMediate]:SEQuence4INITiate[:IMMediate]:NAME PROGram

TRIG:SEQ4 TRIG:PROG

Executes a software trigger for the SEQuence4 (PROgram) group.

Command TRIGger:SEQuence4[:IMMediate]TRIGger:PROGram[:IMMediate]

TRIG:SEQ4:SOUR TRIG:PROG:SOUR

Sets an applicable trigger source for the SEQuence4 (PROgram) group.

Command TRIGger:SEQuence4:SOURce {BUS|IMMediate|EXTernal}TRIGger:SEQuence4:SOURce?

Command TRIGger:PROGram:SOURce {BUS|IMMediate}TRIGger:PROGram:SOURce?


IMMediate Immediately begin execution (default) EXTernal Begin execution when an edge is applied to the TRIG IN terminal


* RCL* RST

52 PBZ_INTERFACE


SEQuence1 to SEQuence4 Shared Command

ABOR

Aborts measurement.The PBZ’s trigger state immediately after it turns on is the same as its trigger state after it receives an ABOR command.If you send an ABOR command while the PBZ is executing measurements, the measured data is discarded.If you send an ABOR command without first sending an INIT command and if the measurement data that is held in the PBZ is valid, the measured data is not discarded.

Command ABORt

PBZ_INTERFACE 53

8 Memory Function Commands

Preset Memory

MEM:PRES:RCL

Loads preset memory entries.

Command MEMory:PRESet:RCL {1|2|3}

Parameter Value: 1 Preset memory A 2 Preset memory B 3 Preset memory C

MEM:PRES:SAV

Saves the current settings to preset memory.

Command MEMory:PRESet:SAV {1|2|3}

Parameter Value: 1 Preset memory A 2 Preset memory B 3 Preset memory C

Setup Memory

MEM:SET:RCL

Loads the setup memory entry that you specify by its memory number.

Command MEMory:SETup:RCL {0|1|2|3|4|5|6|7|8|9}

Parameter Value: 0 to 9 Memory number

54 PBZ_INTERFACE

Memory Function Commands

MEM:SET:SAV

Saves the current settings to the setup memory entry that you specify by its memory number.

Command MEMory:SETup:SAV {0|1|2|3|4|5|6|7|8|9}

Parameter Value:


MEM:SET:TITL

Specify the setup memory number and sets the name to a string of 15 characters in length. A space character(0x20) is inserted automatically in case of a string of less than 15 characters in length.

Command MEMory:SETup:TITLe {0|1|2|3|4|5|6|7|8|9},<“string”>MEMory:SETup:TITLe? {0|1|2|3|4|5|6|7|8|9}


Parameter Value: <“string”> Character string

Response Returns the name of the setup memory entry in <“string”> format in response to the MEMory:SETup:TITLe? {0|1|2|3|4|5|6|7|8|9} query.

PBZ_INTERFACE 55

9 Sequence Function Commands

Editing Programs and Steps

Selecting Programs

PROG:NAME

Selects the program that corresponds to the specified program number, or clears the current selection.

Command PROGram:NAME <“string”>PROGram:NAME?

Parameter Value: “1” to “16” Program number “” Blank string (clears the current selection; default)

Response Returns the name of the program in <“string”> format in response to the PROG:NAME? query.

Editing Programs

PROG:EDIT:ADD

Adds the specified number of steps to the selected program. Steps are added after the program’s final step.

Command PROGram:EDIT:ADD <NRf>

Parameter Value: 1 to 1024 Number of steps to add

PROG:EDIT:COUN

Queries the number of steps in the selected program.

Command PROGram:EDIT:COUNt?

Response Returns the number of steps in the program in <NR1> format in response to the PROG:EDIT:COUN? query.

* RCL* RST

56 PBZ_INTERFACE

Sequence Function Commands

PROG:EDIT:COUN:FREE

Queries the number of steps that can be added to the selected program.

Command PROGram:EDIT:COUNt:FREE?

Response Returns the number of steps that can be added to the program in <NR1> format in response to the PROG:EDIT:COUN:FREE? query.

PROG:EDIT:DEL

Deletes all of the selected program’s steps.

Command PROGram:EDIT:DELete

PROG:EDIT:TITLSets the name of the selected program to a string of 15 characters in length. A space character(0x20) is inserted automatically in case of a string of less than 15 characters in length.

Command PROGram:EDIT:TITLe <“string”>PROGram:EDIT:TITLe?


Example “My Program”

Response Returns the selected program’s name in <“string”> format.

PROG:EDIT:FUNC:MODESets the selected program’s CV/CC mode setting.

Command PROGram:EDIT:FUNCtion:MODE {CC|CV}PROGram:EDIT:FUNCtion:MODE?

Parameter Value: CC CC mode CV CV mode

Response Returns the setting in <character> format in response to the PROG:EDIT:FUNC:MODE? query.

PROG:EDIT:FUNC:POLSets the selected program’s bipolar/unipolar mode setting.

Command PROGram:EDIT:FUNCtion:POLarity {BIPolar|UNIPolar}PROGram:EDIT:FUNCtion:POLarity?

Parameter Value: BIPolar Bipolar mode (default) UNIPolar Unipolar mode

Response Returns the setting in <character> format in response to the PROG:EDIT:FUNC:POL? query.

PBZ_INTERFACE 57


PROG:EDIT:LOOP

Sets the number of times that the selected program will repeat.

Command PROGram:EDIT:LOOP <NRf>PROGram:EDIT:LOOP?

Parameter Value: 1 to 10 000 10 001 (infinity)

Response Returns the number of times that the program will repeat in <NR3> format in response to the PROG:EDIT:LOOP? query.

Selecting Steps

PROG:EDIT:STEP:SEL

Selects the selected program’s step that corresponds to the specified step number.

Command PROGram:EDIT:STEP:SELect <NRf>PROGram:EDIT:STEP:SELect?

Parameter Value: 1 to 1024 Step number: The maximum value is the number of steps that have been added to the program.

Response Returns the step number in <NR1> format in response to the PROG:EDIT:STEP:SEL? query. Returns <-1> if there are no steps in the selected program.

58 PBZ_INTERFACE


Editing Steps (DC Signal Settings)

PROG:EDIT:STEP:CURR PROG:EDIT:STEP:VOLT

Sets the DC signal voltage, current, and how the signal will change over time for the selected step. If you specify IMMediate, the DC signal voltage and current are set to the specified values immediately at the start of the step. If you specify RAMP, the DC signal voltage and current increase or decrease gradually from the start of the step and are set to the specified values at the end of the step.If the step time exceeds 1 000 seconds, the DC signal level after 1 000 seconds is the same as the DC signal stop setting (STOP). If you want to perform a ramp transition that takes longer than 1 000 seconds, you have to combine multiple steps.

Command PROGram:EDIT:STEP:VOLTage[:LEVel] {<numeric>|MIN|MAX}[,<character>]

PROGram:EDIT:STEP:VOLTage[:LEVel]? [{MIN|MAX}]

Command PROGram:EDIT:STEP:CURRent[:LEVel] {<numeric>|MIN|MAX}[,<character>]

PROGram:EDIT:STEP:CURRent[:LEVel]? [{MIN|MAX}]


Parameter Value: IMMediate Change levels immediately RAMP Change levels gradually The default is IMMediate.

Response Returns the settings in <NR3>,<character> format in response to the PROG:EDIT:STEP:VOLT? or PROG:EDIT:STEP:CURR? query.

PROG:EDIT:STEP:CURR:RAMP PROG:EDIT:STEP:VOLT:RAMP

Sets the value of the DC signal current and voltage at the start of the step when the selected step is set to RAMP (change gradually).

Command PROGram:EDIT:STEP:VOLTage:RAMP {<numeric>|MIN|MAX}PROGram:EDIT:STEP:VOLTage:RAMP? [{MIN|MAX}]

Command PROGram:EDIT:STEP:CURRent:RAMP {<numeric>|MIN|MAX}PROGram:EDIT:STEP:CURRent:RAMP? [{MIN|MAX}]


Response Returns the setting in <NR3> format in response to the PROG:EDIT:STEP:VOLT:RAMP? or PROG:EDIT:STEP:CURR:RAMP? query.

PBZ_INTERFACE 59


Editing Steps (AC Signal Settings)

PROG:EDIT:STEP:FUNC

Sets the AC signal waveform of the selected step. There are three types of fixed waveforms (sine, square, and triangle waves), and you can store up to 16 user-defined arbitrary waveforms.

Command PROGram:EDIT:STEP:FUNCtion[:SHAPe] {SINusoid|SQUare|TRIangle|USER[1]..USER16}

PROGram:EDIT:STEP:FUNCtion[:SHAPe]?

Parameter Value: SINusoid Sine wave SQUare Square wave TRIangle Triangle wave USER[1] to USER16 User-defined arbitrary waveform

Response Returns the AC signal waveform type in <character> format in response to the PROG:EDIT:STEP:FUNC? query.

PROG:EDIT:STEP:CURR:AC PROG:EDIT:STEP:VOLT:AC

Sets the AC signal voltage, current, and how the signal will change over time for the selected step. If you specify IMMediate, the AC signal voltage and current are set to the specified values immediately at the start of the step. If you specify SWEep, the AC signal voltage and current increase or decrease gradually from the start of the step and are set to the specified values at the end of the step.

Command PROGram:EDIT:STEP:VOLTage:AC {<numeric>|MIN|MAX}[,<character>]

PROGram:EDIT:STEP:VOLTage:AC? [{MIN|MAX}]

Command PROGram:EDIT:STEP:CURRent:AC {<numeric>|MIN|MAX}[,<character>]

PROGram:EDIT:STEP:CURRent:AC? [{MIN|MAX}]


Parameter Value: IMMediate Change levels immediately SWEep Change levels gradually The default is IMMediate.

Response Returns the settings in <NR3>,<character> format in response to the PROG:EDIT:STEP:VOLT:AC? or PROG:EDIT:STEP:CURR:AC? query.

60 PBZ_INTERFACE


PROG:EDIT:STEP:CURR:AC:SWE PROG:EDIT:STEP:VOLT:AC:SWE

Sets the value of the AC signal current and voltage at the start of the step when the selected step is set to SWEep (change gradually).If the step time exceeds 1 000 seconds, the AC signal amplitude level after 1 000 seconds is the same as the stop amplitude setting (STOP). If you want to perform an AC signal amplitude sweep that takes longer than 1 000 seconds, you have to combine multiple steps.

Command PROGram:EDIT:STEP:VOLTage:AC:SWEep {<numeric>|MIN|MAX}PROGram:EDIT:STEP:VOLTage:AC:SWEep? [{MIN|MAX}]

Command PROGram:EDIT:STEP:CURRent:AC:SWEep {<numeric>|MIN|MAX}PROGram:EDIT:STEP:CURRent:AC:SWEep? [{MIN|MAX}]


Response Returns the setting in <NR3> format in response to the PROG:EDIT:STEP:VOLT:AC:SWE? or PROG:EDIT:STEP:CURR:AC:SWE? query.

PROG:EDIT:STEP:AC:STAT

Sets the selected step’s AC signal on/off state.

Command PROGram:EDIT:STEP:AC:STATe {ON|OFF|1|0}PROGram:EDIT:STEP:AC:STATe?

Parameter Value: ON (1) On OFF (0) Off

Response Returns the selected step’s AC signal on/off state in <NR1> format in response to the PROG:EDIT:STEP:AC:STAT? query.

PBZ_INTERFACE 61


PROG:EDIT:STEP:FREQ

Sets the AC signal frequency and how the frequency will change over time for the selected step. If you specify IMMediate, the AC signal frequency is set to the specified value immediately at the start of the step. If you specify SWEep, the AC signal frequency increases or decreases gradually from the start of the step and it is set to the specified value at the end of the step.

Command PROGram:EDIT:STEP:FREQuency {<numeric>|MIN|MAX}[,<character>]PROGram:EDIT:STEP:FREQuency? [{MIN|MAX}]

Parameter Value: PBZ20-20/PBZ40-10/PBZ60-6.7/PBZ80-5: +1.0E-02 Hz to +1.0E+05 Hz Maximum CV mode: +1.0E+05 (100 kHz)

CC mode: +1.0E+05 (100 kHz)

PBZ20-20A: +1.0E-02 Hz to +2.0E+05 Hz Maximum CV mode: +2.0E+05 (200 kHz)


Parameter Value: IMMediate Change levels immediately SWEep Change levels gradually The default is IMMediate.

Response Returns the settings in <NR3>,<character> format in response to the PROG:EDIT:STEP:FREQ? query.

PROG:EDIT:STEP:FREQ:SWE

Sets the AC signal frequency sweep mode and the frequency at the start of the step for the selected step.If the step time exceeds 1 000 seconds, the frequency sweep from the specified start frequency to the specified stop frequency is repeated after 1 000 seconds. If you want to perform an AC signal frequency sweep that takes longer than 1 000 seconds, you have to combine multiple steps.

Command PROGram:EDIT:STEP:FREQuency:SWEep [<character>],{<numeric>|MIN|MAX}

PROGram:EDIT:STEP:FREQuency:SWEep? <character>[,{MIN|MAX}]

Parameter Value: LOG Logarithmic sweep LINear Linear sweep

Parameter Value: PBZ20-20/PBZ40-10/PBZ60-6.7/PBZ80-5: +1.0E-02 Hz to +1.0E+05 Hz (start frequency) Maximum CV mode: +1.0E+05 (100 kHz)

CC mode: +1.0E+05 (100 kHz)

PBZ20-20A: +1.0E-02 Hz to +2.0E+05 Hz (start frequency) Maximum CV mode: +2.0E+05 (200 kHz)


Response Returns the settings in <character>,<NR3> format in response to the PROG:EDIT:STEP:FREQ:SWE? query.

62 PBZ_INTERFACE


PROG:EDIT:STEP:PHAS

Sets AC signal start phase angle and whether to set the start phase angle or not for the selected step.

Command PROGram:EDIT:STEP:PHASe {<numeric>|MIN|MAX},{ON|OFF|1|0}PROGram:EDIT:STEP:PHASe?

Parameter Value: 0 to 359Unit: DEG (degrees)

Parameter Value: ON (1) Set the start phase angle OFF (0) Do not set the start phase angle

Response Returns the start phase angle setting and whether the start phase angle is set or not in <NR3>,<NR1> format in response to the PROG:EDIT:STEP:PHAS? query.

PROG:EDIT:STEP:SQU:DCYC

Sets the square wave signal duty cycle for the selected step.

Command PROGram:EDIT:STEP:SQUare:DCYCle {<numeric>|MIN|MAX}PROGram:EDIT:STEP:SQUare:DCYCle? [{MIN|MAX}]

Parameter Value: 0.1 % to 99.9 % (The default value is 50.0 %.)Unit: PCT

Response Returns the setting in <NR3> format in response to the PROG:EDIT:STEP:SQU:DCYC? query.

PBZ_INTERFACE 63


Editing Steps (Execution Time, Turning Output On and Off, and Trigger I/O)

PROG:EDIT:STEP:TIME

Sets the execution time for the selected step.The DC signal ramp and AC signal amplitude sweep both stop after 1 000 seconds. The AC signal frequency sweep repeats once every 1 000 seconds. If you want to perform these functions for lengths of time exceeding 1 000 seconds, you have to combine multiple steps.

Command PROGram:EDIT:STEP:TIME {<numeric>|MIN|MAX}PROGram:EDIT:STEP:TIME? [{MIN|MAX}]

Parameter Value: 0.0001 to 3 600 000Unit: S

Response Returns the setting in <NR3> (number of digits to the right of the decimal is 5) format in response to the PROG:EDIT:STEP:TIME? query.

PROG:EDIT:STEP:STAT

Sets the selected step to turn output on or off and sets the selected step’s trigger signal I/O.

Command PROGram:EDIT:STEP:STATe {ON|OFF|1|0},{ON|OFF|1|0},{ON|OFF|1|0}

PROGram:EDIT:STEP:STATe?

Parameter Value: ON (1) Turns output on OFF (0) Turns output off

Parameter Value: ON (1) Generate trigger signal output OFF (0) Do not generate trigger signal output

Parameter Value: ON (1) Wait for trigger signal input OFF (0) Ignore trigger signal input

Response Returns the settings in <NR1>,<NR1>,<NR1> format in response to the PROG:EDIT:STEP:STAT? query.

64 PBZ_INTERFACE


Executing Programs

PROG:EXEC:STAT

Changes the execution state of the selected program.

Command PROGram:EXECute:STATe {RUN|PAUSE|STOP|CONTinue}

Parameter Value: RUN Execute the program PAUSE Pause execution STOP Stop execution CONTinue Continue execution

PROG:EXEC

Queries the execution state of the selected program.

Command PROGram:EXECuting?

Response Returns the execution state, time that has passed since execution began, the number of times that the program will repeat, the current step number, and the program number in <character>,<NR3> (number of digits to the right of the decimal is 5),<NR1>,<NR1>, <“string”> format in response to the PROG:EXEC? query.

Response format <character>: The execution state (RUN, PAUSE, STOP, or WAIT). <NR3>: The time that has passed since execution began. <NR1>: The number of times that the program will repeat. <NR1>: The current step number. <“string”>: The program number.

Example When the execution mode is RUN: RUN,+1.00000E+00,1,1,“1”.

Example When the execution mode is STOP: STOP,0,0,-1,“”.

PBZ_INTERFACE 65


Editing Scripts

SCR:NAME

Selects the script or clears the current selection.

Command SCRipt:NAME <“string”>SCRipt:NAME?

Parameter Value: “CC” CC script “CV” CV script “” Blank string (clears the current selection; default)

Response Returns the name of the script in <“string”> format in response to the SCR:NAME? query.

SCR:EDIT

Sets the contents of the selected script.

Command SCRipt:EDIT <“string”>SCRipt:EDIT?

Parameter Value: “DO Pn,Rn” Selects a program number. Pn: Program number (1 to 16). Rn: The number of times Pn will repeat (1 to 10 000; 10 001 for infinity).

“DO LOOP Ln” Loop start command. Ln: The number of times the loop will repeat (1 to 10 000; 10 001 for infinity).

“END LOOP” Loop end command.

Example SCR:EDIT “DO P1,R1;DO P2,R1;DO LOOP L2;DO P3,R1;END LOOP”

Parameters are separated by semicolons.

Response Returns the script editing string in <“string”> format in response to the SCR:EDIT? query.

SCR:EDIT:TITL

Sets the name of the selected script to a string of 15 characters in length. A space character(0x20) is inserted automatically in case of a string of less than 15 characters in length.

Command SCRipt:EDIT:TITLe <“string”>SCRipt:EDIT:TITLe?


Example “My SCRipt”

Response Returns the selected script’s name in <“string”> format.

* RCL* RST

66 PBZ_INTERFACE

10 System Settings Commands

CONFIG Settings

SYST:CONF:BTR

Trips the breaker (turns the POWER switch off).

Command SYSTem:CONFigure:BTRip[:IMMediate]

SYST:CONF:BTR:PROT

Sets whether to trip the breaker or not when overvoltage protection (OVP) and overcurrent protection (OCP) are activated.

Command SYSTem:CONFigure:BTRip:PROTection {ON|OFF|1|0}SYSTem:CONFigure:BTRip:PROTection?

Parameter Value: ON (1) Trip the breaker OFF (0) Do not trip the breaker

Response Returns whether the breaker trips (the POWER switch turns off) or not in <NR1> format in response to the SYST:CONF:BTR:PROT? query.

SYST:CONF:PAR

Sets the number of units that are operating in parallel. This can only be set on the master unit. This cannot be set when the output is on. This setting is changed after the PBZ is reset.

Command SYSTem:CONFigure:PARallel {1|2|3|4|5}SYSTem:CONFigure:PARallel?

Parameter Value: 1 to 5 (The default value is 1.)

Response Returns the setting for the number of units that are operating in parallel in <NR1> format in response to the SYST:CONF:PAR? query.

PBZ_INTERFACE 67

System Settings Commands

SYST:CONF:MSL

Sets the PBZ’s parallel operation mode. This setting is changed after the PBZ is reset.

Command SYSTem:CONFigure:MSLave {MASTer|PARallel}SYSTem:CONFigure:MSLave?

Parameter Value: PARallel Slave unit MASTer Master unit or independent operation

Response Returns the parallel operation mode in <character> format in response to the SYST:CONF:MSL? query.

SYST:CONF:SYNC:OPER

Sets the PBZ’s synchronous operation mode.

Command SYSTem:CONFigure:SYNC:OPERation {OFF|MASTer|SLAVe|STERmination}

SYSTem:CONFigure:SYNC:OPERation?

Parameter Value: OFF Do not perform synchronous operation (default) MASTer Master unit SLAVe Slave unit STERmination Slave end unit

Response Returns the synchronous operation mode in <character> format in response to the SYST:CONF:SYNC:OPER? query.

SYST:CONF:TRAC

Executes a debug trace and sets whether communication errors are displayed or not. If you turn the debug trace feature on, error numbers, such as Err-100, are displayed on the screen.

Command SYSTem:CONFigure:TRACe {ON|OFF|1|0}SYSTem:CONFigure:TRACe?

Parameter Value: ON (1) Communication errors are displayed. OFF (0) Communication errors are not displayed.

Response Returns whether communication errors are displayed or not in <NR1> format in response to the SYST:CONF:TRAC? query.

SYST:CONF:PRES:RCL:MOD

Sets the method for loading preset memory entries.

Command SYSTem:CONFigure:PRESet:RCL:MODe {<numeric>|MIN|MAX}SYSTem:CONFigure:PRESet:RCL:MODe?

Parameter Value: 1 1KEY mode 2 2KEY mode (default)

Response Returns the method for loading preset memory entries in <NR1> format in response to the SYST:CONF:PRES:RCL:MOD? query.

* RCL* RST

* RCL* RST

68 PBZ_INTERFACE


SYST:CONF:RSEN

Sets whether to perform remote sensing or not.

Command SYSTem:CONFigure:RSENsing {ON|OFF|1|0}SYSTem:CONFigure:RSENsing?

Parameter Value: ON (1) Perform remote sensing OFF (0) Do not perform remote sensing

Response Returns whether remote sensing is performed or not in <NR1> format in response to the SYST:CONF:RSEN? query.

SYST:CONF:KLOC:LEV

Sets the key lock security level for the front panel keys.

Command SYSTem:CONFigure:KLOCk:LEVel {1|2|3|MIN|MAX]}SYSTem:CONFigure:KLOCk:LEVel?

Parameter Value: 1 Level 1 2 Level 2 3 Level 3 (default)

Unit: None

Response Returns the key lock security level for the front panel keys in <NR1> format in response to the SYST:CONF:KLOC:LEV? query.

SYST:CONF:BEEP:STAT

Turns the buzzer on and off.

Command SYSTem:CONFigure:BEEPer:STATe {ON|OFF|1|0}SYSTem:CONFigure:BEEPer:STATe?

Parameter Value: ON (1) On (default) OFF (0) Off

Response Returns whether the buzzer is on or off in <NR1> format in response to the SYST:CONF:BEEP:STAT? query.

SYST:CONF:BEEP:VOL

Sets the buzzer volume.

Command SYSTem:CONFigure:BEEPer:VOLume {<numeric>|MIN|MAX}SYSTem:CONFigure:BEEPer:VOLume? [{MIN|MAX}]

Parameter Value: 0.0 to 1.0 (The default value is 1.0.)Unit: None.

Response Returns the buzzer volume setting in <NR3> format.

* RCL* RST

* RCL* RST

* RCL* RST

PBZ_INTERFACE 69


SYST:CONF:PON:STAT

Sets the power-on state.

Command SYSTem:CONFigure:PON:STATe {DEFault|LAST}SYSTem:CONFigure:PON:STATe?

Parameter Value: LAST The settings that were in use immediately before the POWER switch was turned off (default).

DEFault The factory default settings.

Response Returns the power-on state in <character> format in response to the SYST:CONF:PON:STAT? query.

SYST:CONF:SEQ:PON:STAT

Sets the program or script to execute when the PBZ turns on.

Command SYSTem:CONFigure:SEQuence:PON:STATe <“string”>SYSTem:CONFigure:SEQuence:PON:STATe?

Parameter Value: “1” to “16” Program number “CV” CV script “CC” CC script “” Blank string (clears the current selection; default)

Response Returns the name of the program or script to execute when the PBZ turns on in <“string”> format in response to the SYST:CONF:SEQ:PON:STAT query.

* RCL* RST

* RCL* RST

70 PBZ_INTERFACE


Basic System Settings

SYST:ERR

Retrieves the oldest error from the error queue. The error queue can hold up to 255 errors. The error queue is cleared if a *CLS command is sent.

Command SYSTem:ERRor[:NEXT]?

Response Returns the oldest error held in the error queue in <NR1>,<“string”> format.

Example If there are no errors:0,“No error”

Example If there is a command error:-100,“Command error”

SYST:KLOC

Locks and unlocks the panel keys.

Command SYSTem:KLOCk {ON|OFF|1|0}SYSTem:KLOCk?

Parameter Value: ON (1) Lock the panel keys OFF (0) Unlock the panel keys

Response Returns whether the panel keys are locked or not in <NR1> format.

SYST:LOC

Sets the PBZ to local mode (panel operation). This is a substitute command for the IEEE 488.1 REN message (Remote Enable). You can switch the PBZ back to remote mode by sending the SYST:REM or SYST:RWL command.If the PBZ is using the GPIB interface, an SCPI error (-200, “Execution error”) occurs.

Command SYSTem:LOCal

SYST:REM

Sets the PBZ to remote mode. All panel keys, except the LOCAL key, are locked. This is a substitute command for the IEEE 488.1 REN message (Remote Enable). This is also the substitute command for address specification.You can switch the PBZ back to local mode by sending the SYST:LOC command.If the PBZ is using the GPIB interface, an SCPI error (-200, “Execution error”) occurs.

Command SYSTem:REMote

PBZ_INTERFACE 71


SYST:RWL

Sets the PBZ to remote mode. All panel keys (including the LOCAL key) are locked. This is a substitute command for the IEEE 488.1 llo message (Local Lock Out).You can switch the PBZ back to local mode by sending the SYST:LOC command.If the PBZ is using the GPIB interface, an SCPI error (-200, “Execution error”) occurs.

Command SYSTem:RWLock

SYST:OPT

Queries the options that are installed in the PBZ. This command performs the same function as the *OPT? command.

Command SYSTem:OPTion?

Response If the factory option LAN interface board is installed, “LAN” is returned. Returns “0” if no options are installed.

SYST:VERS

Queries the version of the SCPI specifications that the PBZ complies with.

Command SYSTem:VERSion?

Response Always returns 1 999.0.

72 PBZ_INTERFACE

11 Status Register and Status Report Function

IEEE 488.2 and SCPI registers are used for status reports.In each SCPI status register, there are the following sub registers: the CONDition register, the EVENt register, the ENABle register, the PTRansition filter, and the NTRansition filter.The figure on page 73 shows the SCPI status register structure. A “+” represents the logical OR of the register bits.The tables on pages 74 to 78 provide the bit numbers, bit weights, bit names, and the meaning of each bit.

CONDition register

The CONDition register transits automatically and reflects the condition of the PBZ in real time. Reading this register does not affect its contents.

EVENt register

The EVENt register bits are automatically set according to the changes in the CONDition register. The rule for setting the bits varies depending on the positive and negative transition filters (PTRansition and NTRansition). The EVENt register is reset when it is read.

ENABle register

The ENABle register enables reports to the summary bit or status bit of the event bits.

Transition filter

Use the PTRansition (positive transition) filter to report events when the condition changes from false to true.Use the NTRansition (negative transition) filter to report events when the condition changes from true to false.If both the positive filter and negative filter are set to true, events can be reported each time the status changes.If both filters are cleared, event reporting is disabled.

PBZ_INTERFACE 73

Status Register and Status Report Function

SCPI status registers

I-LIMIT(CURRENT LIMIT)

Not UsedPOW(AC POWER OFF)

OT(OVER Temperature)OP(OVER POWER)

Not UsedNot Used

V-LIMIT(VOLTAGE LIMIT)

Not UsedSD(SHUTDOWN ALARM)

P-LIMIT(POWER LIMIT)UNLOCKED

Not UsedNot Used*

Not UsedNot UsedNot UsedNot Used

Not UsedNot Used

Not UsedCC

TDEL(TRANSIENT DELAY)Not UsedNot Used

PROGRAMNot Used

CV

OV(OVER VOLTAGE)OC(OVER CURRENT)

Partially changed SCPI Standard 1999.0 Volume 1 fig. 9-1

74 PBZ_INTERFACE


IEEE 488.2 Register Model

Status Byte Register

The status byte register stores STB and RQS (MSS) messages as defined by the IEEE 488.1 standard.The status byte register can be read by using IEEE 488.1 serial polling or the IEEE 488.2 common command *STB?.When the controller executes serial polling, bit 6 responds with request service (RQS). The status byte value is not changed by serial polling.*STB? makes the PBZ transmit the contents of the status byte register and the master status summary (MSS) message.*STB? does not change the status byte, MSS, and RQS.

Bit Bit weight

Bit name Description

0 1 Reserved Reserved for future use by IEEE 488. The bit value is notified as zero.1 2 Reserved

2 4 Error/Event Queue If data exists in the error or event queue, this bit is set to true.

3 8 Questionable Status Register (QUES)

This bit is set to true when a bit is set in the QUEStionable event status register and the corresponding bit in the QUEStionable status enable register is true.

4 16 Message Available (MAV) This bit is set to true when a request is received from the digital programming interface and the PBZ is ready to generate the data byte.

5 32 Standard Event Status Bit Summary (ESB)

This bit is set to true when a bit is set in the event status register.

6 64 Request Service (RQS) This bit is set to true when a bit is set in the service request enable register and the corresponding bit exists in the status byte.The SRQ line of the GPIB is set.

Master Status Summary (MSS) This bit is set to true when any bit in the status byte register is set to 1 and the corresponding bit in the service request enable register is set to 1.

7 128 Operation Status Register (OPER)

This bit is set to true when a bit is set in the OPERation event status register and the corresponding bit in the OPERation status enable register is set.

8-15 – NOT USED —

PBZ_INTERFACE 75


Event Status Register (Standard Event Status Register)

The event status register bits are set when certain events occur during PBZ operation. All the event status register bits are set by the error event queue.This register is defined by the IEEE 488.2 standard and is controlled by the IEEE 488.2 common commands *ESE, *ESE?, and *ESR?.

Bit Bit weight


0 1 Operation Complete (OPC) Set when an *OPC command is received and all operations in standby complete.

1 2 Request Control (RQC) —

2 4 Query Error (QYE) Set when an attempt is made to read data from the output queue when there is no data or when the output queue is not in the wait state.This indicates that there is no data in the output queue.

3 8 Device Dependent Error (DDE)

Set when there is a device-specific error.

4 16 Execution Error (EXE) Set when the PBZ evaluates that the program data after the header is outside the formal input range or does not match the specifications of the PBZ.This indicates that a valid SCPI command may not be executed correctly depending on the state of the PBZ.

5 32 Command Error (CME) Set when an IEEE 488.2 syntax error is detected by the parser, when an unidentifiable header is received, or when a group execution trigger enters the internal IEEE 488.2 SCPI command input buffer.

6 64 User Request (URQ) —

7 128 Power ON (PON) Set when the power is turned on.

8-15 – Reserved —

76 PBZ_INTERFACE


SCPI Register Model

OPERation Status Register (STATus:OPERation)

The OPERation status register is a 16-bit register that contains information about conditions that are part of normal PBZ operation.

STAT:OPER

Queries the event of the OPERation status register.A query clears the contents of the register.

Command STATus:OPERation[:EVENt]?

Response Returns the event of the OPERation status register in <NR1> format.

STAT:OPER:COND

Queries the condition of the OPERation status register.A query does not clear the contents of the register.

Command STATus:OPERation:CONDition?

Response Returns the condition of the OPERation status register in <NR1> format.

Bit Bit weight


0 1 NOT USED —

1 2 NOT USED —

2 4 NOT USED —

3 8 NOT USED —

4 16 MEASuring Indicates whether measurement is in progress on the PBZ.

5 32 Waiting for TRIGger Indicates whether the PBZ is waiting for a trigger (TRIG).

6 64 NOT USED —

7 128 NOT USED —

8 256 Constant Voltage Indicates whether the PBZ is in CV mode.

9 512 NOT USED —

10 1024 Constant Current Indicates whether the PBZ is in CC mode.

11 2048 TRANsient Delay Indicates whether the PBZ is delaying execution.

12 4096 NOT USED —

13 8192 NOT USED —

14 16384 PROGram Indicates whether the PBZ is executing a program.

15 32768 NOT USED —

PBZ_INTERFACE 77


STAT:OPER:ENAB

Sets the enable register of the OPERation status register.

Command STATus:OPERation:ENABle <NRf>STATus:OPERation:ENABle?

Parameter Value: 0 to 32 767

Response Returns the enable register of the OPERation status register in <NR1> format.

STAT:OPER:PTR

Sets the positive transition filter of the OPERation status register.

Command STATus:OPERation:PTRansition <NRf>STATus:OPERation:PTRansition?


Response Returns the positive transition filter of the OPERation status register in <NR1> format.

STAT:OPER:NTR

Sets the negative transition filter of the OPERation status register.

Command STATus:OPERation:NTRansition <NRf>STATus:OPERation:NTRansition?


Response Returns the negative transition filter of the OPERation status register in <NR1> format.

78 PBZ_INTERFACE


QUEStionable Status Register (STATus:QUEStionable)

The QUEStionable status register is a 16-bit register that stores information related to the PBZ’s status and the questionable events that occur during PBZ operation.These register bits may indicate that there are problems with the PBZ’s measured data.

STAT:QUES

Queries the event of the QUEStionable status register.A query clears the contents of the register.

Command STATus:QUEStionable[:EVENt]?

Response Returns the event of the QUEStionable status register in <NR1> format.

STAT:QUES:COND

Queries the condition of the QUEStionable status register.A query does not clear the contents of the register.

Command STATus:QUEStionable:CONDition?

Response Returns the condition of the QUEStionable status register in <NR1> format.

Bit Bit weight


0 1 Over Voltage Overvoltage protection has been activated.

1 2 Over Current Overcurrent protection has been activated.

2 4 Not Used —

3 8 AC Power OFF The POWER switch is off.

4 16 Over Temp The overheat sensor has been activated.

5 32 Over Power The power limit protection has been activated.

6 64 Not Used —

7 128 Not Used —

8 256 V-Limit The voltage limit has been activated.

9 512 I-Limit The current limit has been activated.

10 1024 Not Used —

11 2048 Shutdown Alarm The POWER switch was turned off.

12 4096 Power Limit The power limit has been activated.

13 8192 UNLOCKED The PBZ is unsynchronized.

14 16384 Not Used —

15 32768 Not Used —

PBZ_INTERFACE 79


STAT:QUES:ENAB

Sets the enable register of the QUEStionable status register.

Command STATus:QUEStionable:ENABle <NRf>STATus:QUEStionable:ENABle?


Response Returns the enable register of the QUEStionable status register in <NR1> format.

STAT:QUES:PTR

Sets the positive transition filter of the QUEStionable status register.

Command STATus:QUEStionable:PTRansition <NRf>STATus:QUEStionable:PTRansition?


Response Returns the positive transition filter of the QUEStionable status register in <NR1> format.

STAT:QUES:NTR

Sets the negative transition filter of the QUEStionable status register.

Command STATus:QUEStionable:NTRansition <NRf>STATus:QUEStionable:NTRansition?


Response Returns the negative transition filter of the QUEStionable status register in <NR1> format.

80 PBZ_INTERFACE


Preset Status

STAT:PRES

Resets the ENABle, PTRansition, and NTRansition filter registers of all status registers (including sub registers) to their default values.Default values:

STATus:ENABle = 0x0000STATus:PTRansition = 0x7FFFSTATus:NTRansition = 0x0000

Command STATus:PRESet

Configures the status data, and enables certain events to be reported at a high level by the status reporting mechanism. These events are summarized in the OPERation status register and the QUEStionable status register that are part of the required structure.STAT:PRES only affects the transition filter registers of the ENABle register and the status data structure.STAT:PRES does not clear any event registers, nor does it clear any items from the error or event queues.To reset all event registers and the queues in the device’s status reporting mechanism, send the *CLS command.For status data that SCPI requires, STAT:PRES sets the transition filters so that they recognize only positive transitions and sets the ENABle register to all 0. The service request enable register, parallel polling enable register, memory registers that are related to the *SAV command, the PBZ’s address, the output queue, and the power-on status clear flag are not affected by this command.

Register preset values that can be set by the user

Register Filter or enable Preset value

QUEStionableOPERation

Enable register All zeros

Positive transition filter All ones

Negative transition filter All zeros

PBZ_INTERFACE 81

12 Default State

The following tables show the PBZ settings (default state) when you send a *RST, *RCL, or MEAS? command or when you turn PBZ on. In each table, “MEAS?” represents the MEAS:<meas_item> command.

SYSTem subsystem

DISPlay subsystem

CommandSetting

Unit Function*RST *RCL MEAS? Power on

SYST:KLOC – – –

The settings that were in use immediately before the POWER switch was turned off.

– Panel key lock

SYST:CONF:BTR:PROT– – – –

Breaker tripping when a protection feature is activated

SYST:CONF:PAR – – – – Number of units in parallel operation

SYST:CONF:MSL – – – – Parallel operation: master/slave

SYST:CONF:SYNC:OPER

OFF

Depends on the settings in the memory

– – Synchronous operation: master/slave

SYST:CONF:TRAC – – – – Communication error display

SYST:CONF:PRES:RCL :MOD 2


– – Preset memory loading method

SYST:CONF:RSEN – – – Remote sensing

SYST:CONF:KLOC:LEV 3 – – Panel key lock and key lock level

SYST:CONF:BEEP:STAT 1 (ON) – – Buzzer: on/off

SYST:CONF:BEEP:VOL 1.0 – – Buzzer volume

SYST:CONF:PON:STAT LAST – – Power-on state

SYST:CONF:SEQ:PON:STAT “” (Blank

string)– –

Program or script to execute when the PBZ turns on

CommandSetting


DISP:CONT

0.7 – –

The setting that was in use immediately before the POWER switch was turned off.

– Screen contrast

82 PBZ_INTERFACE

Default State

OUTPut subsystem

SENSe subsystem

CommandSetting


OUTP 0 (OFF) 0 (OFF) –


– Output: on/off

OUTP:TRIG IMMediate IMMediate – – Output: on/off according to software triggers

OUTP:PON:STAT RST


– – Output: on/off when the PBZ turns on

OUTP:EXT NORMal – – Output-on control signal polarity

OUTP:TRIG:POL POSitive – – Trigger signal output polarity

OUTP:TRIG:STAT 0 (OFF) – – Trigger signal output: on/off

OUTP:PORT 0 (OFF) – – – J1 connector and option terminal output: on/off

CommandSetting


SENS:APER 0.1Depends on the settings in the memory

– The settings that were in use immediately before the POWER switch was turned off.

S Measurement time

SENS:FUNC DC – – Measurement function

SENS:TRIG:DEL 0 – S Trigger delay

SENS:TRIG:SOUR AUTO – – Measurement start trigger source

PBZ_INTERFACE 83

Default State

[SOURce] subsystem

CommandSetting


FUNC:MODE CV


–


– CV/CC modeFUNC:POL BIPolar – – Bipolar/unipolar modeFUNC:SOUR INTernal – – Signal source selectionFUNC:EXT:TERM BNC – – External signal source terminal

selectionFUNC:EXT:CURR:GAIN 0 – A/V External signal source gainFUNC:EXT:VOLT:GAIN 0 – V/V External signal source gainFUNC SIN – – AC signal selectionFUNC:TRIG IMMediate IMMediate – – AC signal source selection

according to software triggersAC:STAT

0 (OFF)


– – AC signal: on/off

AC:STAT:TRIG IMMediate IMMediate – – AC signal: on/off according to software triggers

VOLT 0 Depends on the settings in the memory

– V DC signal voltage valueVOLT:TRIG IMMediate – V DC signal voltage value

according to software triggersVOLT:AC 0 – VPP AC signal voltage value

VOLT:AC:TRIG IMMediate IMMediate – VPP AC signal voltage value according to software triggers

CURR 0 Depends on the settings in the memory

– A DC signal current valueCURR:TRIG IMMediate – A DC signal current value

according to software triggersCURR:AC 0 – APP AC signal current value

CURR:AC:TRIG IMMediate IMMediate – APP AC signal current value according to software triggers

FREQ

1 kHz


–HZ AC signal frequency value

FREQ:TRIG IMMediate IMMediate HZ AC signal frequency value according to software triggers

PHAS 0 or 1 (ON)


– DEG – AC signal start phase angle

SQU:DCYC 50.0 – PCT Square wave signal duty cycleSWE:STAT 0 (OFF) – – Frequency sweep: on/offSWE:SPAC LINear – – Frequency sweep modeSWE:TIME 1 – S Frequency sweep timeSWE:FREQ:STAR 100 Hz – HZ Frequency sweep start

frequencySWE:FREQ:STOP 1 kHz – HZ Frequency sweep stop

frequencyMARK 0 (OFF) – – TRIG OUT terminal output typeMARK:FPO 500 Hz – HZ Marker frequencyAPPL:DC APPL:SIN APPL:SQU APPL:TRI APPL:USER{[1]...16}

– – – HZCollective settings (AC signal waveform, frequency, amplitude, and DC signal)

– – – VPP APP

– – – V A

84 PBZ_INTERFACE

Default State

[SOURce] subsystem

MEASure & TRIGger subsystem

INPut subsystem

CommandSetting


CURR:RESP35


–


USCC mode response (PBZ20-20/ PBZ60-67/ PBZ80-5)

70 – US CC mode response (PBZ40-10)

VOLT:RESP 3.5 – US CV mode response

CURR:PROT:OVER CURR:LIM:UPP CURR:PROT:UPP

110 % of the rated value

– A Positive current activation point

VOLT:PROT:OVER VOLT:LIM:UPP VOLT:PROT:UPP


– V Positive voltage activation point

CURR:PROT:UND CURR:LIM:LOW CURR:PROT:LOW


– A Negative current activation point

VOLT:PROT:UND VOLT:LIM:LOW VOLT:PROT:LOW


– V Negative voltage activation point

CURR:PROT:STAT LIMIT – – OCP mode

VOLT:PROT:STAT LIMIT – – OVP mode

CommandSetting


TRIG:SOUR TRIG:TRAN:SOUR IMMediate – IMMediate IMMediate – SEQuence1 trigger

source

TRIG:SEQ2:SOUR TRIG:OUTP:SOUR IMMediate – IMMediate IMMediate – SEQuence2 trigger

source

TRIG:SEQ2:SST:RISE TRIG:OUTP:SST:RISE 0.0 Depends

on the settings in the memory

No change No change S SEQuence2 soft start

time

TRIG:SEQ2:SST:FALL TRIG:OUTP:SST:FALL 0.0 No

change No change S SEQuence2 soft stop time

TRIG:SEQ3:SOUR TRIG:ACQ:SOUR IMMediate – IMMediate IMMediate – SEQuence3 trigger

source

TRIG:SEQ4:SOUR TRIG:PROG:SOUR IMMediate – IMMediate IMMediate – SEQuence4 trigger

source

CommandSetting


INP:TRIG:POL

POSitive


–


– Trigger signal input polarity

PBZ_INTERFACE 85

Default State

PROGram subsystem

SCRipt subsystem

CommandSetting


PROG:NAME “” (Blank string)

“” (Blank string)

–


– Program selection and selection clearing

PROG:EDIT:FUNC:MODE – – – – Program: CV/CC mode

PROG:EDIT:FUNC:POL – – – – Program: bipolar/unipolar mode

PROG:EDIT:LOOP – – – – Number of times that the program will repeat

PROG:EDIT:STEP:CURR PROG:EDIT:STEP:VOLT – – – V

A

Step’s DC signal value; value at the end of step if RAMP is specified

– – – – Step’s signal change

PROG:EDIT:STEP:CURR:RAMP PROG:EDIT:STEP:VOLT:RAMP – – – V

AStep’s DC signal RAMP start value

PROG:EDIT:STEP:FUNC – – – – Step’s AC signal waveform

PROG:EDIT:STEP:CURR:AC PROG:EDIT:STEP:VOLT:AC – – – VPP

APP

Step’s AC signal value; value at the end of step if SWE is specified

PROG:EDIT:STEP:CURR:AC:SWE PROG:EDIT:STEP:VOLT:AC:SWE – – – VPP

APPStep’s AC signal SWE start value

PROG:EDIT:STEP:AC:STAT – – – – Step’s AC signal on/off

PROG:EDIT:STEP:FREQ – – – – Step’s AC signal frequency change

PROG:EDIT:STEP:FREQ:SWE – – – – Step’s AC signal frequency sweep mode

– – – HZStep’s AC signal frequency sweep start frequency

– – – HZStep’s AC signal frequency sweep stop frequency

PROG:EDIT:STEP:PHAS – – – DEG Step’s AC signal start phase angle– – – –

PROG:EDIT:STEP:SQU:DCYC 50 % – – PCT Step’s square wave duty cycle

PROG:EDIT:STEP:TIME – – – S Step execution time

PROG:EDIT:STEP:STAT – – – – Output: on/off

– – – – Trigger signal output

– – – – Trigger signal input

CommandSetting


SCR:NAME


“” (Blank string) –


– Script selection and selection clearing

86 PBZ_INTERFACE

13 Processing time of Commands

The command processing time is the time until the next command is accepted.The processing times indicated here are typical values. They are not warranted.The processing times vary depending on the settings and the measurement conditions.It does not include the response time of the hardware.

CommandGPIB1

Processing Time (ms)

1 Using GPIB-USB-B by National Instruments.

USBProcessing Time (ms)

RS232C2


2 Data rate setting: 38 400 bps. Flow control: On

LAN3


3 100BASE-TX Ethernet

Description

VOLT 20 47 47 47 47 Sets the DC signal voltage value.

MEAS:VOLT?4

4 Measurement time: 0.1 s

145 145 145 145 Queries the DC voltage measurement.

CURR 20 47 47 47 47 Sets the DC signal current value.

MEAS:CURR?*4 145 145 145 145 Queries theDC current measurement.

*RST 260 260 260 260 Performs a device reset.

PBZ_INTERFACE 87

14 List of Messages

SCPI Command: Command name in the short form. Effect: “Yes” for commands that are affected by the *RST and *RCL commands. R/W: “R” for query commands and “W” for set commands. †: “1” for SCPI standard commands, “2” for commands that are being

reviewed, and “3” for original commands developed by Kikusui Electronics Corporation.

SYSTem subsystem

DISPlay subsystem

SCPI command SettingDefault Response Effect Description R/W †

Program header Parameter UnitSYST

:CONF:BTR – – – – – – Breaker tripping W 3

:BTR:PROT bool ON | OFF – – NR1 – Breaker tripping when a protection feature is activated R/W 3

:PAR NRf 1 to 5 – – NR1 – Number of units in parallel operation R/W 3

:MSL character MAST | PAR – – char – Parallel operation: master/slave R/W 3

:SYNC:OPER character OFF | MAST | SLAV | ATER – – char – Synchronous operation: master/

slave R/W 3

:TRAC bool ON | OFF – – NR1 – Communication error display R/W 3:PRES:RCL:MOD numeric 1 | 2 – 2 NR1 – Preset memory loading method R/W 3

:RSEN bool ON | OFF – – NR1 – Remote sensing R/W 3:KLOC:LEV numeric 1 | 2 | 3 – 3 NR1 – Panel key lock and key lock level R/W 3:BEEP

:STAT bool ON | OFF – ON NR1 – Buzzer: on/off R/W 3:VOL numeric 0.0 to 1.0 – 1.0 NR3 – Buzzer volume R/W 3

:PON:STAT character DEF | LAST – LAST char – Power-on state R/W 3:SEQ:PON:STAT string

“1” to “16”, “CV”, “CC”, or

“”– “” (Blank

string) string – Program or script to execute when the PBZ turns on R/W 3

:ERR[:NEXT] – – – – NR1, string – Queries error and event

information R 1

:KLOC bool ON | OFF – – NR1 – Panel key lock R/W 3:LOC – – – – – – Switches to local mode W 2

:REM – – – – – – Switches to remote mode; locks all keys other than LOCAL and STOP W 2

:RWL – – – – – – Switches to remote mode; locks all keys other than STOP W 2

:OPT – – – – – – Queries options R 3

:VERS – – – – 1 999.0 – Queries the version of the compliant SCPI specifications R 1


Program header Parameter UnitDISP

:CONT numeric 0.0 to 1.0 – 0.7 NR3 – Screen contrast R/W 3

88 PBZ_INTERFACE

List of Messages

MEMory subsystem

OUTPut subsystem

INPut subsystem

SENSe subsystem


Program header Parameter UnitMEM

:PRES:RCL NRf 1 to 3 – – – – Preset memory loading W 3:SAV NRf 1 to 3 – – – – Preset memory saving W 3

:SET:RCL NRf 0 to 9 – – – – Setup memory loading W 3:SAV NRf 0 to 9 – – – – Setup memory saving W 3:TITL NRf

string0 to 9string – – NR1

string – Setup memory name and memory number R/W 3


Program header Parameter UnitOUTP

[:STAT] bool ON | OFF – OFF NR1 – Output: on/off R/W 3

:TRIG bool ON | OFF – IMM NR1 – Output: on/off according to software triggers R/W 3

:PON:STAT character RST | AUTO – RST char – Output: on/off when the PBZ turns on R/W 3

:EXT character NORM | INV – NORM char – Output-on external control signal polarity R/W 3

:TRIG:POL character POS | NEG – POS char – Trigger signal output polarity R/W 3:TRIG:STAT bool ON | OFF – OFF NR1 – Trigger signal output: on/off R/W 3:PORT bool ON | OFF – OFF NR1 – Option output: on/off R/W 3:PROT:CLE – – – – – – Alarm clearing W 3


Program header Parameter UnitINP

:TRIG:POL character POS | NEG – POS char – Trigger signal input polarity R/W 3


Program header Parameter UnitSENS

:APER numeric 0.0001 to 3600 – 0.1 NR3 Yes Measurement time R/W 3

:FUNC character DC | AC | DCAC | PEAK – DC char – Measurement function R/W 3

:TRIG:DEL numeric 0.000 00 to 3600 – 0 NR3 Yes Trigger delay R/W 3

:TRIG:SOUR characterAUTO | INT |

EXTPOS | EXTNEG

– AUTO char – Measurement start trigger source R/W 3

PBZ_INTERFACE 89

List of Messages

[SOURce] subsystem


Program header Parameter Unit[SOUR:]

FUNC character SIN | SQU | TRI | USER[1] to 16 – SIN char Yes AC signal selection R/W 3

:MODE character CV | CC – CV char Yes CV/CC mode R/W 3:POL character BIP | UNIP – BIP char Yes Bipolar/unipolar mode R/W 3:SOUR character INT| EXT | BOTH – INT char Yes Signal source selection R/W 3TRIG character SIN | SQU | TRI |

USER[1] to 16 – IMM char Yes AC signal source selection according to software triggers R/W 3

:EXT:TERM character BNC| J1 | BOTH – BNC char Yes External signal source terminal

selection R/W 3

:EXT:CURR:GAIN numeric 0 to 20 or 0 to 10 A/V 0 NR3 Yes External signal source gain R/W 3

:EXT:VOLT:GAIN numeric 0 to 20 or 0 to 40 V/V 0 NR3 Yes External signal source gain R/W 3

USERx:TITL string – – – string – User-defined arbitrary waveform’s name R/W 3

USERx:DATA string – – – string – User-defined arbitrary waveform’s pattern R/W 3

USERx:DATA:FORM:BORD

character NORM | SWAP – – char YesUser defined arbitrary waveform’s binary transmission data byte order

R/W 3

USERx:DATA:VAL numeric addr:0 to 1 023

data:-32 768 to +32 767 – – NR1 –Sets the value at an address in a user-defined arbitrary waveform pattern.

R/W 3

VOLT numeric 0 % to 105 % of the rated value V 0 NR3 Yes DC signal voltage value R/W 3

:TRIG numeric 0 % to 105 % of the rated value V IMM NR3 Yes DC signal voltage value

according to software triggers R/W 3

:AC numeric 0 % to 105 % of the rated value VPP 0 NR3 Yes AC signal voltage value R/W 3

:TRIG numeric 0 % to 105 % of the rated value VPP IMM NR3 Yes AC signal voltage value


:PROT:OVER numeric +1 % to +110 % of the

rated value V +110 % NR3 Yes Positive OVP activation point R/W 3

:UND numeric -110 % to -1 % of the rated value V -110 % NR3 Yes Negative OVP activation point R/W 3

:UPP

numeric

+OVP: +1 % to +110 % of the rated value

-110 % ≤ -V.LIM ≤ +V.LIM ≤ +110 % of the rated

value

V +110 % NR3 Yes Positive OVP/V.LIM activation point R/W 3

:LOW

numeric

-OVP: -110 % to -1 % of the rated value


value

V -110 % NR3 Yes Negative OVP/V.LIM activation point R/W 3

:STAT character LIMIT | TRIP – LIMIT char Yes OVP mode R/W 3:LIM

:UPPnumeric


valueV +110 % NR3 Yes Positive V.LIM activation point R/W 3

:LOWnumeric


valueV -110 % NR3 Yes Negative V.LIM activation point R/W 3

90 PBZ_INTERFACE

List of Messages

[SOUR:]CURR numeric 0 % to 105 % of the rated

value A 0 NR3 Yes DC signal current value R/W 3

:TRIG numeric 0 % to 105 % of the rated value A IMM NR3 Yes DC signal current value


:AC numeric 0 % to 105 % of the rated value APP 0 NR3 Yes AC signal current value R/W 3

:TRIG numeric 0 % to 105 % of the rated value APP IMM NR3 Yes AC signal current value


:PROT:OVER numeric +1 % to +110 % of the

rated value A -110 % NR3 Yes Positive OCP activation point R/W 3

:UND numeric -110 % to -1 % of the rated value A -110 % NR3 Yes Negative OCP activation point R/W 3

:UPP numeric +1 % to +110 % of the rated value A +110 % NR3 Yes Positive OCP/I.LIM activation

point R/W 3

:LOW numeric -110 % to -1 % of the rated value A -110 % NR3 Yes Negative OCP/I.LIM activation

point R/W 3

:STAT character LIMIT | TRIP – LIMIT char Yes OCP mode R/W 3:PROT

:UPP numeric +1 % to +110 % of the rated value A +110 % NR3 Yes Positive I.LIM activation point R/W 3

:LOW numeric -110 % to -1 % of the rated value A -110 % NR3 Yes Negative I.LIM activation point R/W 3

FREQnumeric CV:1.0E-02 to 1.0E+05

CC:1.0E-02 to 1.0E+05 HZ 1.0E+03 NR3 YesAC signal frequency value (PBZ20-20/PBZ40-10/PBZ60-6.7/PBZ80-5)

R/W 3

numeric CV:1.0E-02 to 2.0E+05CC:1.0E-02 to 2.0E+05 HZ 1.0E+03 NR3 Yes AC signal frequency value

(PBZ20-20A) R/W 3

:TRIG

numeric CV:1.0E-02 to 1.0E+05CC:1.0E-02 to 1.0E+05 HZ IMM NR3 Yes

AC signal frequency value according to software triggers (PBZ20-20/PBZ40-10/PBZ60-6.7/PBZ80-5)

R/W 3

numeric CV:1.0E-02 to 2.0E+05CC:1.0E-02 to 2.0E+05 HZ IMM NR3 Yes

AC signal frequency value according to software triggers (PBZ20-20A)

R/W 3

PHAS numeric 0 to 359 DEG 0 NR3 YesAC signal start phase angle

R/W 3bool ON | OFF – ON NR1 Yes R/W 3

SQU:DCYC numeric 0.1 to 99.9 PCT 50.0 NR3 Yes Square wave signal duty cycle R/W 3SWE

:STAT bool ON | OFF – OFF NR1 Yes Frequency sweep: on/off R/W 3:SPAC character LOG | LIN – LIN char Yes Frequency sweep mode R/W 3:TIME numeric 0.0001 to 1000 S 1 NR3 Yes Frequency sweep time R/W 3:FREQ

:STARnumeric CV:1.0E-02 to 1.0E+05

CC:1.0E-02 to 1.0E+05 HZ 1.0E+02 NR3 YesFrequency sweep start frequency (PBZ20-20/PBZ40-10/PBZ60-6.7/PBZ80-5)

R/W 3

numeric CV:1.0E-02 to 2.0E+05CC:1.0E-02 to 2.0E+05 HZ 1.0E+02 NR3 Yes Frequency sweep start

frequency (PBZ20-20A) R/W 3

:STOPnumeric CV:1.0E-02 to 1.0E+05

CC:1.0E-02 to 1.0E+05 HZ 1.0E+03 NR3 YesFrequency sweep stop frequency (PBZ20-20/PBZ40-10/PBZ60-6.7/PBZ80-5)

R/W 3

numeric CV:1.0E-02 to 2.0E+05CC:1.0E-02 to 2.0E+05 HZ 1.0E+03 NR3 Yes Frequency sweep stop

frequency (PBZ20-20A) R/W 3

MARK bool ON | OFF – OFF NR1 Yes TRIG OUT terminal output type R/W 3:FPO numeric CV:1.0E-02 to 1.0E+05

CC:1.0E-02 to 1.0E+05 HZ 500 NR3 Yes Marker frequency (PBZ20-20/PBZ40-10/PBZ60-6.7/PBZ80-5) R/W 3

numeric CV:1.0E-02 to 2.0E+05CC:1.0E-02 to 2.0E+05 HZ 500 NR3 Yes Marker frequency (PBZ20-20A) R/W 3


Program header Parameter Unit

PBZ_INTERFACE 91

List of Messages

MEASure/TRIGger subsystem

[SOUR:]APPL

:DC :SIN :SQU :TRI :USERx

– – – – char – Collective settings (AC signal waveform) R/W 3

numeric CV:1.0E-02 to 1.0E+05CC:1.0E-02 to 1.0E+05 HZ – NR3 Yes

Collective settings (AC signal frequency) (PBZ20-20/PBZ40-10/PBZ60-6.7/PBZ80-5)

R/W 3

numeric CV:1.0E-02 to 2.0E+05CC:1.0E-02 to 2.0E+05 HZ – NR3 Yes Collective settings (AC signal

frequency) (PBZ20-20A) R/W 3

numeric 0 % to 105 % of the rated value APP – NR3 Yes Collective settings (AC signal

amplitude) R/W 3

numeric 0 % to 105 % of the rated value V – NR3 Yes Collective settings (DC signal) R/W 3

CURR:RESP numeric 35| 100 | 350 | 1 000 US 35 NR3 Yes CC mode response (PBZ20-20/ PBZ20-20/PBZ80-5) R/W 3

numeric 70| 100 | 350 | 1 000 US 70 NR3 Yes CC mode response (PBZ40-10) R/W 3VOLT:RESP numeric 3.5| 10 | 35 | 100 US 3.5 NR3 Yes CV mode response R/W 3:AC

:STAT bool ON | OFF – OFF NR1 Yes AC signal: on/off R/W 3:STAT:TRIG bool ON | OFF – IMM NR1 Yes AC signal: on/off according to

software triggers R/W 3




Program header Parameter UnitFETC[:SCAL] | READ[:SCAL] | MEAS[:SCAL]

:CURR[:DC] – – A – NR3 – DC current measurement R 3:AC – – A – NR3 – AC current measurement (RMS) R 3:MIN – – APP – NR3 – Minimum current measurement (bottom value) R 3:MAX – – APP – NR3 – Maximum current measurement (peak value) R 3

:VOLT[:DC] – – V – NR3 – DC voltage measurement R 3:AC – – V – NR3 – AC voltage measurement (RMS) R 3:MIN – – VPP – NR3 – Minimum voltage measurement (bottom value) R 3:MAX – – VPP – NR3 – Maximum voltage measurement (peak value) R 3

ABOR – – – – – – Measurement aborting W 1INIT[:IMM]

[:SEQ[1]] – – – – – – Starts the trigger function that sets the voltage, current, AC waveform, and frequency W 1

:SEQ2 – – – – – – Starts the trigger function that turns output on and off W 1

:SEQ3 – – – – – – Starts the trigger function that starts measurements and queries measured results W 1

:SEQ4 – – – – – – Starts the trigger function that executes programs and scripts W 1

[:IMM]:NAME TRAN – – – – – – Starts the trigger function that sets the voltage,

current, AC waveform, and frequency W 1

[:IMM]:NAME OUTP – – – – – – Starts the trigger function that turns output on

and off W 1

[:IMM]:NAME ACQ – – – – – – Starts the trigger function that starts

measurements and queries measured results W 1

[:IMM]:NAME PROG – – – – – – Starts the trigger function that executes

programs and scripts W 1

92 PBZ_INTERFACE

List of Messages

TRIG[:SEQ[1]] – – – – – – Executes SEQuence1 software triggers W 1

:SOUR character IMM | BUS – IMM char Yes SEQuence1 trigger source selection R/W 3

:SEQ2 – – – – – – Executes SEQuence2 software triggers W 1:SOUR character IMM |

BUS – IMM char Yes SEQuence2 trigger source selection R/W 3

:SST:RISE numeric 0.0 to 3600 S 0.0 NR3 Yes SEQuence2 soft start time R/W 3

:SST:FALL numeric 0.0 to 3600 S 0.0 NR3 Yes SEQuence2 soft stop time R/W 3

:SEQ3 – – – – – – Executes SEQuence3 software triggers W 1:SOUR character IMM |


:SEQ4 – – – – – – Executes SEQuence4 software triggers W 1:SOUR

characterIMM | BUS | EXT

– IMM char Yes SEQuence4 trigger source selection R/W 3

:TRAN – – – – – – Executes SEQuence1 software triggers W 1:SOUR character IMM |


:OUTP – – – – – – Executes SEQuence2 software triggers W 1:SOUR character IMM |


:OUTP:SST:RISE numeric 0.0 to

3600 S 0 NR3 Yes SEQuence2 soft start time R/W 3

:OUTP:SST:FALL numeric 0.0 to

3600 S 0 NR3 Yes SEQuence2 soft stop time R/W 3

:ACQ – – – – – – Executes SEQuence3 software triggers W 1:SOUR character IMM |


:PROG – – – – – – Executes SEQuence4 software triggers W 1:SOUR

characterIMM | BUS | EXT

– IMM char Yes SEQuence4 trigger source selection R/W 3



PBZ_INTERFACE 93

List of Messages

PROGram subsystem


Program header Parameter UnitPROG

:NAME string 1 to 16 | “” –“”

(Blank string)

string – Program selection and selection clearing R/W 3

:EDIT:ADD NRf – – – – – Number of steps to add W 3:COUN – – – – NR1 – Queries the number of steps R 3

:FREE – – – – NR1 – Queries the number of steps that can be added R 3

:DEL – – – – – – Deletes all steps from the selected program W 3

:TITL string – – – string – Selected program’s name R/W 3:FUNC:MODE character CC | CV – – char – Selected program’s CV/CC mode R/W 3

:FUNC:POL character BIP | UNIP – – char – Selected program’s bipolar/unipolar mode R/W 3

:LOOP NRf 1 to 10 000 | 10 001 – – NR3 – Number of times that the selected

program will repeat R/W 3

:STEP:SEL NRf – – – NR1 – Selected program’s step number

selection R/W 3

:FUNC

character

SIN | SQU | TRI |

USER[1] to 16

– – char – Selected step’s AC signal waveform selection R/W 3

:CURRnumeric

0 % to 105 % of the rated value

A – NR3 YesSelected step’s DC signal current value; value at the end of step if RAMP is specified

R/W 3

character IMM | RAMP – – char – Selected step’s DC signal current change R/W 3

:CURR:RAMP numeric


A – NR3 Yes Selected step’s DC signal RAMP start value R/W 3

:CURR:ACnumeric


APP – NR3 YesSelected step’s AC signal current value; value at the end of step if SWE is specified

R/W 3

character IMM | SWE – – char – Selected step’s AC signal current change R/W 3

:VOLTnumeric


V – NR3 YesSelected step’s DC signal voltage value; value at the end of step if RAMP is specified

R/W 3

character IMM | RAMP – – char – Selected step’s DC signal voltage change R/W 3

:VOLT:RAMP numeric


V – NR3 Yes Selected step’s DC signal RAMP start value R/W 3

:VOLT:ACnumeric


VPP – NR3 YesSelected step’s AC signal voltage value; value at the end of step if SWE is specified

R/W 3

character IMM | SWE – – char – Selected step’s AC signal voltage change R/W 3

:FREQ

numeric

CV:1.0E-02 to 1.0E+05CC:1.0E-02 to 1.0E+05

HZ – NR3 YesSelected step’s AC signal frequency (PBZ20-20/PBZ40-10/PBZ60-6.7/PBZ80-5)

R/W 3

numeric

CV:1.0E-02 to 2.0E+05CC:1.0E-02 to 2.0E+05

HZ – NR3 Yes Selected step’s AC signal frequency (PBZ20-20A) R/W 3

character IMM | SWE – – char – Selected step’s AC signal frequency change R/W 3

94 PBZ_INTERFACE

List of Messages

PROGram:EXECute subsystem

SCRipt subsystem

PROG:EDIT:STEP:FREQ:SWE character LOG | LIN – – char Yes Selected step’s AC signal frequency

sweep mode R/W 3

numeric

CV:1.0E-02 to 1.0E+05CC:1.0E-02 to 1.0E+05

HZ – NR3 YesSelected step’s AC signal frequency sweep start frequency (PBZ20-20/PBZ40-10/PBZ60-6.7/PBZ80-5)

R/W 3

numeric

CV:1.0E-02 to 2.0E+05CC:1.0E-02 to 2.0E+05

HZ – NR3 Yes Selected step’s AC signal frequency sweep stop frequency (PBZ20-20A) R/W 3

:PHAS numeric 0 to 359 DEG – NR3 Yes Selected step’s AC signal start phase angle

R/W 3bool ON | OFF – – NR1 Yes R/W 3

:SQU:DCYC numeric 0.1 to 99.9 PCT 50 NR3 Yes Selected step’s square wave signal

duty cycle R/W 3

:AC:STAT bool ON | OFF – – NR1 Yes Selected step’s AC signal on/off R/W 3:TIME numeric 0.0001 to

3 600 000 S – NR3 Yes Selected step’s frequency sweep time R/W 3

:STAT bool ON | OFF – – NR1 YesSelected step’s output on/off and trigger signal I/O

R/W 3bool ON | OFF – – NR1 Yes R/W 3bool ON | OFF – – NR1 Yes R/W 3




Program header Parameter UnitPROG

:EXEC:STAT character

RUN | PAUSE | STOP | CONT

– – – – Selected program’s execution state W 3

:EXEC – – – – char – Selected program’s execution state (RUN, PAUSE, STOP, or WAIT), time that has passed since execution began, number of times that program will repeat, current step number, and program number.

R 3– – – – NR3 – R 3– – – – NR1 – R 3– – – – NR1 – R 3

– – – – string – R 3


Program header Parameter UnitSCR

:NAME string“CV”, “CC”,


–“”

(Blank string)

string – Script selection and selection clearing R/W 3

:EDIT string “DO Pn,R1” – – string – Selected script’s contents: program

numbers, repetitions, loop start commands, number of times script will repeat, and loop end commands

R/W 3

string “DO LOOP Ln” – – string – R/W 3

string “END LOOP” – – string – R/W 3

:EDIT:TITL string – – – string – Selected script’s name R/W 3

PBZ_INTERFACE 95

List of Messages

STATus subsystem



Program header Parameter UnitSTAT

:OPER[:EVEN] – – – – NR1 – Queries events1 R 1:COND

– – – – NR1 –Queries the condition of the register1

R 1

:ENAB NRf 0 to 32 767 – – NR1 – Enable register1 R/W 1:NTR NRf 0 to 32 767 – – NR1 – Negative transition filter1 R/W 1:PTR NRf 0 to 32 767 – – NR1 – Positive transition filter1 R/W 1

:PRES – – – – – – Resets filter registers to default values W 1

:QUES[:EVEN] – – – – NR1 – Queries events2 R 1:COND

– – – – NR1 –Queries the condition of the register2

R 1

:ENAB NRf 0 to 32 767 – – NR1 – Enable register2 R/W 1:NTR NRf 0 to 32 767 – – NR1 – Positive transition filter2 R/W 1:PTR NRf 0 to 32 767 – – NR1 – Negative transition filter2 R/W 1

1 OPERation status register2 QUEStionable status register

IEEE 488.2common

commandsParameter Description R/W

*CLS – Clears all the event registers. W

*ESE NR1 Sets or queries the event status enable register bits. R/W

*ESR – Queries the event status register. R

*IDN – Queries the identification string (manufacturer information). R

*OPC – Causes the PBZ to generate the operation complete message in the event status register when all pending device operations have finished. R/W

*OPT – Queries the options that are installed in the PBZ. R

*PSC NR1 Sets or queries whether the service request enable register and the event status enable register are reset to their default values when the PBZ’s power is reset. R/W

*RCL – Aborts measurement and loads the settings that have been saved to setup memory. W

*RST – Performs a device reset. Configures the PBZ to a known condition independent from the usage history of the device. W

*SAV NR1 Saves the current settings to setup memory. W

*SRE NR1 Sets the service request enable register. R/W

*STB – Queries the contents of the status byte register and the master summary status message. R

*TRG – Trigger command. W

*TST – Executes a self-test. R

*WAI – Prevents the PBZ from executing subsequent commands or queries until all operations that are in standby have completed. W

96 PBZ_INTERFACE

15 List of Errors

Command errors

An error in the range [-199, -100] indicates that an IEEE 488.2 syntax error has been detected by the instrument’s parser. The occurrence of any error in this class causes the Command Error bit (bit 5) in the event status register to be set.

Error code Error message description

-100 Command error Generic syntax error.

-101 Invalid character A syntactic element contains an invalid character.

-102 Syntax error An unrecognized command or data type was encountered.

-103 Invalid separator The parser was expecting a separator and encountered an illegal character.

-104 Data type error The parser recognized a data element different than one allowed.

-105 GET not allowed A Group Execute Trigger was received in a program message.

-108 Parameter not allowed More parameters were received than expected for the header.

-109 Missing parameter Fewer parameters were received than required for the header.

-110 Command header error An error was detected in the header.

-120 Numeric data error Generated when parsing a data element which appears to be numeric, including the nondecimal numeric types.

-130 Suffix error Generated when parsing a suffix.

-131 Invalid suffix The suffix does not follow the syntax, or the suffix is inappropriate for the PBZ.

-134 Suffix too long The suffix contained more than twelve characters.

-138 Suffix not allowed A suffix was encountered after a numeric element that does not allow suffixes.

-140 Character data error Generated when parsing a character data element.

-141 Invalid character data Either the character data element contains an invalid character, or the element is not valid.

-144 Character data too Long The character data element contains more than twelve characters.

-148 Character data not allowed A legal character data element was encountered where prohibited by the PBZ.

-150 String data error Generated when parsing a string data element.

-160 Block data error Generated when parsing a block data element.

-170 Expression error Generated when parsing an expression data element.

-180 Macro error Generated when defining a macro or executing a macro.

PBZ_INTERFACE 97

List of Errors

Execution errors

An error in the range [-299, -200] indicates that an error has been detected by the instrument’s execution control block. The occurrence of any error in this class causes the Execution Error bit (bit 4) in the event status register to be set.

Device-specific errors


-200 Execution error (generic) A generic PBZ error.

-203 Command protected Password protected program or query command cannot be executed.

-210 Trigger error A trigger error.

-211 Trigger ignored A trigger was received but ignored.

-213 Init ignored A measurement initiate operation was ignored because measurement is in progress.

-214 Trigger deadlock A deadlock occurred because a query was received before the software trigger.

-220 Parameter error A program data element related error occurred.

-221 Settings conflict A command was received that the PBZ cannot execute in its current condition.

-222 Data out of range Program value was outside the legal range.

-223 Too much data Too many parameters were received for the requirements.

-224 Illegal parameter value Received invalid parameter data.

-230 Data corrupt or stale Received a data query before the measurement completed.

-241 Hardware missing Cannot be executed because the optional hardware is not installed.


-330 Self-test failed The self-test failed.

-360 Communication error A communication error occurred.

-362 Framing error in program message

The stop bit cannot be detected.

-363 Input buffer overrun An overrun occurred in the input buffer.

-365 Time out error A time out error occurred.

98 PBZ_INTERFACE

List of Errors

Query errors

An error in the range [-499, -400] indicates that the output queue control of the instrument has detected a problem with the message exchange protocol described in IEEE 488.2, chapter 6. The occurrence of any error in this class causes the Query Error bit (bit 2) in the event status register to be set.

Operation complete event errors

An error in the range [-899, -800] is used when the PBZ wants to report an IEEE 488.2 operation complete event. This event occurs when the instrument’s synchronization protocol, having been enabled by an *OPC command, completes all selected pending operations.The occurrence of this event causes the Operation Complete bit (bit 0) in the event status register to be set.

PBZ-specific errors


-400 Query error (generic) A generic PBZ error.

-410 Query INTERRUPTED Received a new command before the response was read.

-420 Query UNTERMINATED The controller attempted to read the response after the device received an unsupported query or has not received a query.The -100 “Command error” and this error are stored in the error queue. The controller will time out.

-430 Query DEADLOCKED The error queue, input buffer, and output buffer are full when sending large binary data as a response, and the transmission timing is off.

-440 Query UNTERMINATED after indefinite response

Received a separate query in semicolon-delimited format after a query that returns a response in an indefinite form.Example: *IDN?;SYST:ERR?


-800 Operation complete All selected pending operations in accordance with the IEEE 488.2, 12.5.2 synchronization protocol have completed.


101 Operation denied while in LOCal state

The operation was denied because the PBZ is in local mode.

102 Operation denied while in OUTPut ON state

The operation was denied because the output is on.

103 Operation denied while in PROTection state

The operation was denied because a protection feature is activated.

104 Operation denied while in SLAVe mode

The operation was denied because the PBZ is set to slave mode in parallel operation.

105 Operation denied due to incompatible FUNCtion SOURce

The operation was denied because the signal source is incompatible.

106 Operation denied due to PROGRAM RUNNING

The operation was denied because a sequence program is being executed.

107 Operation denied due to Empty PROGram

The operation was denied because there is no sequence program.

PBZ_INTERFACE 99

16 Tutorial (Visual Basic 2008)

Communicate with the PBZ series using VISA through GPIB, RS232C, USB or LAN.

Setting the "Project"

At first, set the communication driver (VISA liabrary) for the "Project".Click "Project" on the menu bar, then select "Add Reference" to refer "VISA COM 3.0 Type Library".

100 PBZ_INTERFACE

Tutorial (Visual Basic 2008)

Communication through GPIB, RS232C, USB, or LAN

After setting the communication driver, it enables to communicate by GPIB, RS232C, USB, or LAN.The following describes the communication procedure for via VISA.

� Open the VISA

To communicate with the device of GPIB, RS232C, USB, or LAN via VISA, it requires to open the VISA first. When opening the VISA, specify the I/O resource.

Example : To open VISA by using USB Set rm = CreateObject("VISA.GlobalRM")

Set msg = rm.Open("USB::0x0B3E::0x1012::00000001::INSTR", NO_LOCK, 0, "")

"USB::0x0B3E::0x1014::00000001::INSTR" is the I/O resource.The I/O resource is specified by the following constructions. The part indicated with [ ] can be abbreviated. Enter the appropriate value in the part specified in oblique characters.

For VISA, the alias can be used for the I/O resource. When using the alias for the I/O resource, even the alias name to be hard coating directly in the application, it can be easily converted to the appropriate I/O resource name.Example : When using the alias (MYPIA) for the I/O resource. Set msg = rm.Open("MYPIA", NO_LOCK, 0, "")

When the alias is used, the actual I/O resource is specified by such an external configuration table.When using the USB (example for KI-VISA)

GPIB GPIB[board]::PrimaryAddress[::SecondaryAddress][::INSTR]Example : The primary address 3 of the measuring instrument connected to GPIB0.　GPIB0::3::INSTR

Seria (RS232C) ASRL[board][::INSTR]Example : The measuring instrument connected to the serial port COM1.　ASRL1::INSTR

USB USB[board]::VendorID::ProductID::SerialNumber[::InterfaceNumber][::INSTR]Example : The USNTMC measuring instrument having with the vendor ID (VID)2878, Product ID(PID)4114 and serial number "00000001".　USB0::0x0B3E::0x1012::00000001::INSTR

LAN1

p. 11

1 The hostname must be a valid mDNS hostname (a Bonjour hostname that ends in ".local") or a DNS hostname that is managed by an external DNS server (a full-qualified domain name— FQDN). If you are using an mDNS hostname, Apple Bonjour (alternatively, iTunes or Safari) must be installed on your PC.

VXI-11 TCPIP[board]::LAN device name[::inst0][::INSTR]The measuring instrument whose IP address (LAN device name) is 169.254.7.8.　TCPIP::169.254.7.8::INSTRYou can also set the LAN device name using the host name.

SCPI-RAW

TCPIP[board]::LAN device name::portno::SOCKETExample :The measuring instrument whose IP address (LAN device name) is 169.254.7.8. (The "portno" setting of the PCR is normally 5025.) TCPIP::169.254.7.8::5025::SOCKETYou can also set the LAN device name using the host name.

See

PBZ_INTERFACE 101


In case of using VISA other than KI-VISA, please refer to the applied VISA manual.

MYDEV1

102 PBZ_INTERFACE


� Controlling the devices

Next, using such a "Read", "Write" to control the devices.Example: msg.WriteString ("FUNC:MODE CV") 'Specify a CV mode.

　msg.WriteString ("VOLT 10.0") 'Set 10.0 V.

　msg.WriteString ("OUTP 1") 'Output ON.

� Closing the VISA.

Close the VISA at the end.A command for "Open" and "Close" of the VISA is required only once in the program. 　msg.Close

Sample programImports Ivi.Visa.Interop

Public Class Form1

Dim rm As ResourceManager Dim msg As IMessage

Private Sub Form1_Load(ByVal sender As System.Object, ByVal e As System.EventArgs) Handles MyBase.Load rm = CreateObject("VISA.GlobalRM") 'msg = rm.Open("GPIB0::1::INSTR", AccessMode.NO_LOCK, 0, "") 'Example: GPIB 'msg = rm.Open("MYDEV1", AccessMode.NO_LOCK, 0, "") 'Example: Using a alias 'msg = rm.Open("TCPIP::169.254.178.141::INSTR", AccessMode.NO_LOCK, 0, "") 'Example: LAN msg = rm.Open("USB0::0x0B3E::0x1012::FF012345::INSTR", AccessMode.NO_LOCK, 0, "")'Example: USB End Sub

'Query the instrument identity Private Sub cmdIdn_Click(ByVal sender As System.Object, ByVal e As System.EventArgs) Handles cmdIdn.Click msg.WriteString("*IDN?") TextBox1.Text = msg.ReadString(256) End Sub

'Set the operation mode and voltage Private Sub cmdCurr_Click(ByVal sender As System.Object, ByVal e As System.EventArgs) Handles cmdCurr.Click msg.WriteString("OUTP 0") 'Output OFF msg.WriteString("FUNC:MODE CV") 'Specify a CV mode msg.WriteString("VOLT 10.0") 'Set 10.0 V. msg.WriteString("OUTP 1") 'Output ON End Sub

'Query the instrument identity Private Sub cmdMeas_Click(ByVal sender As System.Object, ByVal e As System.EventArgs) Handles cmdMeas.Click msg.WriteString("MEAS:CURR?") TextBox1.Text = msg.ReadString(256) End Sub

Private Sub Form1_Disposed(ByVal sender As Object, ByVal e As System.EventArgs) Handles Me.Disposed msg.Close() End SubEnd Class

PBZ_INTERFACE 103

Bboolean data .................................................................................. 17

Ccharacter data ............................................................................... 17command

description ....................................................................... 19hierarchy .......................................................................... 14syntax ................................................................................ 15units ................................................................................... 18

common commands ............................................................ 16, 20compound commands ............................................................... 15CONDition register ...................................................................... 72

Ddefault state ................................................................................... 81DEFAULT switch ............................................................................ 10

EENABle register ............................................................................. 72EVENt register ................................................................................ 72event status register .................................................................... 75

Ffirmware version ..............................................................................2

GGPIB address, setting .....................................................................7GPIB interface ...................................................................................7

II/O library ...........................................................................................4IEEE 488.1 serial polling .............................................................. 74IEEE 488.2 common command ................................................ 74IEEE Std 488.2 ...................................................................................3interface .............................................................................................3

KKI-VISA .................................................................................................4

LLAN Interface ....................................................................................9LAN RESET switch ......................................................................... 10LAN settings ......................................................................................9list of errors ..................................................................................... 96

Mmeasurement instrument interface standards ......................3messages ......................................................................................... 14

list ....................................................................................... 87

Nnon-numeric parameters ........................................................... 17NRf ..................................................................................................... 17Numeric ........................................................................................... 17numeric parameters .................................................................... 17

OOPERation status register .......................................................... 76

Pparameters ..................................................................................... 17

Qqueries ............................................................................................. 16QUEStionable status register .................................................... 78

Rremote control

list of errors ...................................................................... 96remote interfaces ........................................................................... 3RS232C interface ............................................................................. 5RS232C protocol ............................................................................. 6RS232C settings .............................................................................. 6

SSCPI .............................................................................................. 3, 14SCPI command syntax ................................................................ 14SCPI status registers ..................................................................... 73SEQuence1 ...................................................................................... 45SEQuence2 ...................................................................................... 47SEQuence3 ...................................................................................... 49SEQuence4 ...................................................................................... 51status byte register ...................................................................... 74status register ................................................................................ 72string data ....................................................................................... 17

Tterminator ....................................................................................... 16transition filter ............................................................................... 72

UUSB interface .................................................................................... 8USB settings ..................................................................................... 8

Vversion ................................................................................................ 2VISA library ....................................................................................... 4

INDEX

KIKUSUI ELECTRONICS CORP.

http://www.kikusui.co.jp/en

1-1-3 Higashiyamata, Tsuzuki-ku, Yokohama, 224-0023, JapanTel: +81-45-482-6353 Fax: +81-45-482-6261

Website

If you find any misplaced or missing pages in the manuals, they will be replaced. If the manual gets lost or soiled, a new copy can be provided for a fee. In either case, please contact your Kikusui agent or distributor. At that time, inform your agent or distributor of the “PART NO.” written on the front cover of this manual.Every effort has been made to ensure the accuracy of this manual. However, if you have any questions or find any errors or omissions, please contact your Kikusui agent or distributor.After you have finished reading this manual, store it so that you can use it for reference at any time.

Using the GPIB Interface 7 Communication Interface Manual

Text of Using the GPIB Interface 7 Communication Interface Manual

LabVIEW: Tips & Tricks Ihor Korolov March 2011. Contents GPIB communication VISA: GPIB and Serial port configuration and communication How to create

Using the GPIB Interface 7 Communication Interface ManualPart No. IB027583 Aug 2018 PBZ20-20 PBZ20-20A PBZ40-10 PBZ60-6.7 PBZ80-5 BIPOLAR POWER SUPPLY PBZ Series Communication Interface

RIGOL · FF-150 USB to GPIB interface converter for instrument . USB-GPIB : ... Distribute a GPIB address for the spectrum analyzer via the GPIB host device (PC)

Communication via the GPIB Bus - Teledyne LeCroy

Hardware Manual for use with PCI-GPIB, ISA-GPIB · Chapter One: INTRODUCTION 1.1 HISTORY The GPIB (General Purpose Interface Bus) has become the worldwide standard for connecting

Z+ Series Programmable Power Supplies Datasheet€¦ · Communication Interface - RS232, RS485 & USB standard, IEEE488 (GPIB) & LAN optional Series Operation - Up to two identical

High-Performance IEEE488 GPIB Interface · to GPIB driver API functions ADE VISA Driver API (GPIB-32.DLL) GPIB Cards ... LabVIEW*/TestExec) can significantly simplify the complexity

BACnet Communication Interface Module

TMS320F2812-Serial Communication Interface

Archived: Getting Started with Your PCI-GPIB, PXI -GPIB ... · GPIB Getting Started with Your PCI-GPIB, PXI™-GPIB, or PMC-GPIB and NI-488.2™ for Solaris PCI-GPIB, PXI-GPIB, or

FG410/FG420 Arbitrary/Function Generator Communication ... · 1.4 Selecting the Interface Either GPIB or USB can be used as the interface to be used. The FG410/FG420 cannot be controlled

Communication Interface Manual

Communication Interface OTDR

PX8000 Precision Power Scoper Communication Interface … · Communication Interface. ... the communication interface features. PX8000 Precision Power ... The “EN” and “Z1”

Interface Pci-4302 Gpib Interface Board Manual

IEEE488.2 SCPI (GPIB) Multi-Drop Interface Option...IEEE488.2 SCPI (GPIB) Multi-Drop Interface Option USER MANUAL FOR IEEE PROGRAMMING INTERFACE FOR GENESYSTM POWER SUPPLIES IA586-04-01-Rev

GPIB Hardware Installation Guide and …• Use a GPIB-120B Bus Isolator/Expander to isolate GPIB systems and expand the GPIB interface up to 28 devices. • Use a pair of GPIB-140A

Serial Communication Interface

GPIB, USB and Instrument Control Products...The 82350C interface card is fully compatible with IEEE-488 control and communication standard, de-couples GPIB transfers from PCI bus transfers

Serial Communication Interface (SCI)

Ethernut-GPIB Interface Manual - UBC Physics & …qdg/publications/InternalReports/... · · 2007-09-16Ethernut-GPIB Interface Manual Raymond Meng Gao Quantum Degenerate Gas Laboratory

R&S HO880 IEEE-488 Interface InstallationGuide...Schnittstelle I3E (= GPIB) aktiviert werden. Abb. 2.2: Geräterückseite HM8134-3 Abb. 2.3: GPIB-Schnittstellenauswahl HM8134-3 3 Adressierung

Universal Serial Communication Interface

Programming CONTROL MANUAL IEEE488 (GPIB) RS232 SERIAL LAN INTERFACE

RIGOL - Conrad Electronic · USB-GPIB interface converter, the spectrum analyzer can be connected to the GPIB bus controller of the PC, namely to expand a GPIB interface through which

Keysight 82357B USB/GPIB Interface

XBM Communication Interface Specification

ES4408CON.1 Communication Interface

Agilent 82357B USB / GPIB Interface - Technical Overview

GPIB General Purpose Interface Bus

Documents

Using the GPIB Interface 7 Communication Interface Manual

Text of Using the GPIB Interface 7 Communication Interface Manual