-Unlock all doors on key removal and with one remote press:byte 0, bit 3: Check "Auto unlock on key removal"-46 Central Conv.byte 14, bit 7: Check "Mirror lowering on reverse"-"09 Central Electronics" "Byte 23" "Bit 3-4" is a drop down menu that gives you 00 Turn Lights not active, 08 Turn Lights Via Fog Lights, 10 Turn Lights via High Beam and 18 Turn lights via Xenon Shutter. I Chose 08 Via Fog Lights. I also have Bit 2 Checked.-The first step is to enable the convenience menu--see above.Now, there are five places to verify in module 9 (central electronics). Use the long coding helper.1. Byte 00/bit 5: assistance driving light & leaving home active--set this bit to 1 for active2. Byte 00/bit 7: coming home active--set this bit to 1 for active3. Byte 02/bit 4: coming home mode via--set this bit to 0 for personalization4. Byte 21/bit 6: leaving home variant--set this bit to 0 for LH in LDS5. Byte 23/bit 5: coming home logic--set this bit to 1 for new logic-Open/Close windows, tilt sunroof via remote & close when rain detected09 Cent. Elect.In coding select the second item in the drop down list, RLSOriginal coding: 00208933New coding: 0047107746 Central Conv.byte 6, bit 5: Uncheck "Comfort function power windows/sunroof via remote control inactive"byte 7, bit 2: Check "Comfort opening power windows via remote control active"byte 7, bit 5: Check "Comfort closing power windows via remote control active"byte 8, bit 2: Check "Opening sunroof via remote control active"byte 8, bit 5: Check "Closing sunroof via remote control active"byte 8, bit 6: Check "Sunroof open type (0-slide, 1-tilt)" byte 9: Select 02 "Rain closing active"-open VCDS and go to Select Control Modulego to 09-Central Electronicsclick on codingclick on long coding helperPRESS PAGE UP/DOWN to see all the menues and you will see options for the auto lock, honk disable, coming home, leaving home, footwell lighting(lights up with light on @ 20% or higher brightness) and others... some options show up AFTER you have enabled the feature or disable the feature.

go to 17-instruments, follow above steps and you will see brake pad sensor and seatbelt chime options-HALOGEN DRL AT FULL INTENSITY WITH MAIN BEAMS

Module 09

go to Secure access using code :"20113" 12233

go to adaptation

Channel 4: DRL as Positionlight Brightness...as a default we have 37% here.This means that as position light day work at 5 w intensity.You can set this value up to 100% to have them at full intensity (13w) with main beams on

"Test" "save" and then "Done, go back"

There are two more channels to change things here, but not very useful in my view:Channel 1: Brightness of DRLChannel 2: Brightness of Mains with Highbeam on-Leaving Home LightsThis feature turns on your lights when you unlock the car (if your headlight switch is on). I believe this option is standard if you have the auto lights option. This also adds an option in the MFD lights menu for how long it will stay on.

Module 09 - Cent. Elects.CodingByte 0Bit 5 - Assistance Driving Light_Leaving Home active-Coming Home Lights Active TimeThis sets how long the comning home lights styay on for. This can also be set through the larger MFD if you have the bluetooth option.

Module 09 - Cent. Elects.AdaptationCh.01Set a value between 10 and 60 seconds, must be in 10s.

-Turning Off Sealt Belt Warning

Module 17 - IntrumentsCodingChange 3rd and 4th number in string to 00 as per text comment, or add up the number for the options you have, ie; you have headlight washers if you have xenons, so add that to the value.Select][17 - Instruments][Coding - 07][Long Coding Helper]Click on each of the Byte numbers in step 3) and you'll see the selectable options below.Uncheck the box for "Seatbelt Warning active"-Selective Central Locking (single door opening)By default, when you press the keyfob to unlock the car, it only opens the drivers door with a single click. If you turn this features off, it will unlock all doors with a single click.

Module 46 - Central Conv.CodingByte 0Bit 0 - Selective Central Locking-Address 17 InstrumentsAdaptation 10Select Staging from the drop down listSelect Active from the drop down listSave the changesDone![Select][17 - Instruments][Coding - 07][Long Coding Helper]Click on each of the Byte numbers in step 3) and you'll see the selectable options below.Check the box for "Gauge Test/Needle Sweep active"

Close the Long Coding Helper by clicking the Windows X box on the top right of the screen or clicking the Exit button on the top left of the screen) will send your new Coding value back to the Coding screen.[Do It!]1. --- Lighting ---

Daytime Running Lights Audi A3 ONLY The A3 may use different DRL coding settings, please post the complete Auto-Scan if help is needed.Also see this thread: 2010 A3 DRL via MFA

Daytime Running Lights Found in Coding, Long Coding helper, the lamp systems are different:Factory Xenon Byte 11Factory Halogen Byte 15

Cornering Lights via Front Fog Lights active Found in Coding, Long Coding helper

Notes: The lights may work under the following conditions: - The headlights must be turned on and the steering wheel must be in the turning direction. - Headlights on, fogs off, turn signal on in the turning direction. Also see Byte 17, Adaptive Light/Cornering Light Variant. This seems to control the fogs as cornering lights with turn signal.

Fogs as Daytime Running Lights for Xenon equipped vehicles Fogs onlyByte 11 - un-check "Daytime Running Lights (via Low Beam) active"Byte 14, Bit 1 - Manually modify the binary value from a "0" to a "1"

Fogs and Xenon Headlights as DRLs at the same time for Xenon equipped vehicles Byte 11 - leave this alone (DRL's on)Byte 14, Bit 1 - Manually modify the binary value from a "0" to a "1"

Fogs as Daytime Running Lights for Halogen equipped vehicles Disable Factory Halogen DRL's in Byte 15 - un-check "Daytime Running Lights (via separate lights) active"Byte 14, Bit 1 - Manually modify the binary value from a "0" to a "1"in Byte 14 Bit 1 - if You change it to 1 = DRL via fog lights.in Byte 11 Bit 0 - if You change it to 1 = american lighting mode - light deactivation by hand brakesried this on my Seat Leon Facelift, and came up with a cool result.Standard Byte 18 value was 9D and i changed is to 9C. No fault codes found.Before the change all lights were illuminated when Daytime running lights were enabled.

So my normal front lights and my taillights.

But now only my front lights are active.

But here comes the cool thing. I enabled DRL's on my foglights, and normally also the citylight would illuminate, but they don't anymore... So during the day i drive with only my foglights, and during the night my normal front lights + tail lights.

Notes: - Depending on the Byte 18 coding, this may result in all of the parking lights illuminating.- If you do not have desirable results on Halogen equipped vehicles, please update this thread.

Fog Light behavior with High BeamsFound in Coding, Long Coding helper.

Step 1 Enable Auto Rain Closing1. Open the Central Electronics Controller (09) and click on the Coding option.2. Click the drop down box and choose the RegenLichtSens (RainLightSensor)

3. Note the software coding (00)208933) (most cars have different codings)4. Convert to Hex (0)3 30 255. Add 4 to the left hand value Hex (0)7 30 256. Convert to Decimal (00)471077 and replace the old coding.If youre unclear on the conversion steps see theDecimal to Hex and Hex to Decimal conversion guide.Step 2 Enable Menu to Enable/Disable (optional)1. Open the Comfort System Controller (46)

2. In long coding change Byte 09 to Hex 02

Example13 90 06 88 51 03 48 3F 2D 04 05 8F B0 08 0A 04 88 9C 00to13 90 06 88 51 03 48 3F 2D 02 05 8F B0 08 0A 04 88 9C 00