Assembly Instructions 3-8 Bike

VERTICAL RACK Bicycle Storage & Parking Solutions

Optional

Tools Required:• 9/16” Combination wrench & 7/16“ Combination wrench• Hammer drill (for anchors) • ½” concrete drill bit (for anchors)• Tape measure

Mounting Hardware – part # 6264 (sold separately)Recommended for 8023, 8024, 8043, 8044; REQUIRED for 8033, 8034, 8063, 8064

WARNINGS:• Mounting vertical rack to �oor is recommended for single sided models (8023, 8024, 8043, 8044) and REQUIRED for double sided models (8033, 8034, 8063, 8064).• Manufacturer and seller expressly disclaim any and all liability for personal injury, property damage or loss, whether direct, indirect or incidental, resulting from the incorrect attachment, improper use, inadequate maintenance, or neglect of this product.

WARRANTY:We warrant this product to the �rst consumer to be free from defect in material and workmanship for a period of one year from date of purchase (please retain your sales slip for your records). Any product or part thereof found to be defective within that period will be replaced without charge provided that (1) the product was not misused; (2) no alterations or modi�cations were made; (3) its failure resulted from a defect in material or workmanship and not from normal wear expected in the use of the product; (4) the product or part is delivered, freight prepaid, to Saris Cycling Group. Manufacturer’s only obligation shall be to replace such products or parts proved to be defective. Damage to mounting surface is not covered under warranty.

SKU Decsrip�on Bike Spacing Ceiling Height Footprint W/Bikes8023 3 bike, single sided, non locking ver�cal rack 18" 84" 54"X46"8024 4 bike, single sided, non locking ver�cal rack 18" 84" 75"X46"8043 3 bike, single sided, locking ver�cal rack 18" 84" 54"X90"8044 4 bike, single sided, locking ver�cal rack 18" 84" 75"X90"8033 6 bike, double sided, non locking ver�cal rack 18" 84" 54"X46"8034 8 bike, double sided, non locking ver�cal rack 18" 84" 75"X46"8063 6 bike, double sided, locking ver�cal rack 18" 84" 54"X90"8064 8 bike, double sided, locking ver�cal 18" 84" 75"X90"

Product shown 8024

Part 8023 8024 8043 8044 8033 8034 8063 8064 A 6006 Bike tray, locking 3 4 6 8 B 6003T Bike tray, non locking 3 4 6 8 C Ver�cal 2” square side bar 2 2 2 2 2 2 2 2 D 2” x 24” x 1” C channel stabilizing foot 2 2 2 2 2 2 2 2 E Connec�on plate, 6” x 6” 4 4 4 4 4 4 4 4 F Horizontal cross bar, c channel, 54” long 2 2 2 2 F Horizontal cross bar, c channel, 72” long 2 2 2 2 H Tube caps (2” square plas�c) 2 2 2 2 2 2 2 2 I Carriage Bolt, 1/4 – 20 x ½” 10 10 10 10 20 20 20 20 J Carriage Bolt, ¼-20 x 2.5” 8 8 8 8 8 8 8 8 K Carriage Bolt, 3/8 – 16 x 3” 8 8 8 8 8 8 8 8 L Nut, 3/8-16 8 8 8 8 8 8 8 8 M Nut, ¼ - 20 18 18 18 18 28 28 28 28

Product shown 8024

Step 2

STEP 1: LEG ASSEMBLY• Assemble side supports and connect feet (part D - 2x24x1) to side support vertical tubes (part C), using connection plate (part E), and Carriage Bolt (part K)

C

F

STEP 2 : HORIZONTAL CROSS BAR• Attach Horizontal Cross bar (Part F) to each vertical side support (part C), using carriage bolt (Part J)

Step 1(x2)

Holes closer to the edge on the ground.

Shown: 8044, 4 bike, single sided, locking vertical rack

3/8 X 3”

1/4 X 2.5”

B

Step 3

STEP 3: ATTACH WHEEL TRAYS TO FRAMESINGLE AND DOUBLE SIDED:

• Standard spacing – standard bike spacing is 18” on center. Use “Square” oriented holes on cross bar (part F) to achieve standard bike spacing. To connect Bike trays to rack, use bolt (part I) and nut (Part M) to secure Bike Tracs to the cross bar (part F).• Note: An additional Bike Trac can be added to all increase bike capacity by 1 bike for single sided racks, and 2 bikes for double sided racks. This will change bike spacing to 14.5” on center. Use Diamond oriented holes on cross bar (part F) when securing bike tracs.

STEP 4: MOUNTING RACK TO FLOOR

Mounting rack to �oor is recommended for single sided models, and required for double sided models.• Before drilling mounting holes in concrete �oor, investigate whether any mechanicals are imbedded in concrete (ie. Radiant heat, water supply or drain pipes…)• Determine desired location of unit (mark hole locations using foot, part D, as a guide).• Using a ½” masonry drill bit, drill holes in cement 2” deep.• Insert anchor shields into holes and tap in place with a hammer.• Align holes in product foot (part D) with anchors and secure with 5/16 -8 x 2” bolts.

Saris Cycling Group 5253 Verona Road Madison WI 53711 USA Ph: 608.274.6550 Fx: 608.274.1702 www.sarisinfrustructure.com

Open Side Down

24214C 10/19

Shown: 8034, 8 bike, double sided, non locking vertical rack

Product shown 8024