VSTAR 1300 XVS13CTX(C) OWNER'S MANUAL… · INTRODUCTION EAU10080 Congratulations on your purchase of the Yamaha XVS13CTX(C). This model is the result of Yamaha’s vast experience

5S6-28199-11

XVS13CTX(C)

OWNER’S MANUAL

LIT-11626-21-30

EAU10041

U5S611E0.book Page 1 Thursday, May 10, 2007 3:00 PM

INTRODUCTIONEAU10080

Congratulations on your purchase of the Yamaha XVS13CTX(C). This model is the result of Yamaha’s vast experience inthe production of fine sporting, touring, and pacesetting racing machines. It represents the high degree of craftsmanship andreliability that have made Yamaha a leader in these fields.This manual will give you an understanding of the operation, inspection, and basic maintenance of this motorcycle. If youhave any questions concerning the operation or maintenance of your motorcycle, please consult a Yamaha dealer.The design and manufacture of this Yamaha motorcycle fully comply with the emissions standards for clean air applicable atthe date of manufacture. Yamaha has met these standards without reducing the performance or economy of operation of themotorcycle. To maintain these high standards, it is important that you and your Yamaha dealer pay close attention to therecommended maintenance schedules and operating instructions contained within this manual.


IMPORTANT MANUAL INFORMATIONEAU10131

Particularly important information is distinguished in this manual by the following notations:

NOTE:� This manual should be considered a permanent part of this motorcycle and should remain with it even if the motorcycle

is subsequently sold.� Yamaha continually seeks advancements in product design and quality. Therefore, while this manual contains the most

current product information available at the time of printing, there may be minor discrepancies between your motorcycleand this manual. If you have any questions concerning this manual, please consult your Yamaha dealer.

The Safety Alert Symbol means ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

Failure to follow WARNING instructions could result in severe injury or death to the motorcycle operator, a bystander or a person inspecting or repairing the motor-cycle.

A CAUTION indicates special precautions that must be taken to avoid damage to the motorcycle.

A NOTE provides key information to make procedures easier or clearer.

WARNING

CAUTION:

NOTE:


IMPORTANT MANUAL INFORMATION

WARNINGEWA10010

PLEASE READ THIS MANUAL AND THE “YOU AND YOUR MOTORCYCLE: RIDING TIPS” BOOKLET CAREFULLYAND COMPLETELY BEFORE OPERATING THIS MOTORCYCLE. DO NOT ATTEMPT TO OPERATE THIS MOTOR-CYCLE UNTIL YOU HAVE ATTAINED ADEQUATE KNOWLEDGE OF ITS CONTROLS AND OPERATING FEATURESAND UNTIL YOU HAVE BEEN TRAINED IN SAFE AND PROPER RIDING TECHNIQUES. REGULAR INSPECTIONSAND CAREFUL MAINTENANCE, ALONG WITH GOOD RIDING SKILLS, WILL ENSURE THAT YOU SAFELY ENJOYTHE CAPABILITIES AND THE RELIABILITY OF THIS MOTORCYCLE.

*Product and specifications are subject to change without notice.


IMPORTANT MANUAL INFORMATION

EAU10192

XVS13CTX(C)OWNER’S MANUAL

©2007 by Yamaha Motor Corporation, U.S.A.1st edition, April 2007

All rights reserved.Any reprinting or unauthorized use without the written permission of Yamaha Motor Corporation, U.S.A.

is expressly prohibited.Printed in Japan.

P/N LIT-11626-21-30

AFFIX DEALER

LABEL HERE


TABLE OF CONTENTSSAFETY INFORMATION ..................1-1

Location of important labels ...........1-5

DESCRIPTION ..................................2-1Left view ..........................................2-1Right view........................................2-2Controls and instruments ................2-3

INSTRUMENT AND CONTROL FUNCTIONS .......................................3-1

Main switch/steering lock ................3-1Indicator and warning lights ............3-2Multi-function meter unit .................3-3Handlebar switches ........................3-6Clutch lever ....................................3-8Shift pedal ......................................3-8Brake lever .....................................3-8Brake pedal ....................................3-9Fuel tank cap ..................................3-9Fuel ..............................................3-10Catalytic converter ........................3-11Rider seat .....................................3-11Helmet holder ...............................3-12Sidebags ......................................3-12Adjusting the shock absorber

assembly ...................................3-13Sidestand .....................................3-14Ignition circuit cut-off system ........3-15

PRE-OPERATION CHECKS..............4-1Pre-operation check list ..................4-2

OPERATION AND IMPORTANT RIDING POINTS ................................ 5-1

Starting the engine ......................... 5-1Shifting ........................................... 5-2Engine break-in .............................. 5-3Parking ........................................... 5-4

PERIODIC MAINTENANCE AND MINOR REPAIR................................. 6-1

PERIODIC MAINTENANCE .......... 6-1Owner’s tool kit .............................. 6-1Periodic maintenance chart for the

emission control system ............. 6-3General maintenance and

lubrication chart .......................... 6-4Removing and installing the

panel ........................................... 6-9Checking the spark plugs .............. 6-9Canister (for California only) ........ 6-11Engine oil and oil filter cartridge ... 6-11Coolant ........................................ 6-14Replacing the air filter element .... 6-15Checking the throttle cable free

play ........................................... 6-16Valve clearance ........................... 6-16Tires ............................................. 6-17Cast wheels ................................. 6-19Accessories and replacement

parts ......................................... 6-19Adjusting the clutch lever free

play ........................................... 6-20

Adjusting the brake lever free play ........................................... 6-20

Adjusting the rear brake light switch ........................................6-21

Checking the front and rear brake pads ................................ 6-21

Checking the brake fluid level ...... 6-22Changing the brake fluid .............. 6-23Drive belt slack .............................6-23Checking and lubricating the

cables ....................................... 6-24Checking and lubricating the

throttle grip and cable ............... 6-24Checking and lubricating the

brake and shift pedals ............... 6-25Checking and lubricating the

brake and clutch levers .............6-25Checking and lubricating the

sidestand .................................. 6-26Lubricating the swingarm pivots ... 6-26Lubricating the rear suspension ... 6-27Checking the front fork ................. 6-27Checking the steering ..................6-28Checking the wheel bearings .......6-28Battery .......................................... 6-29Replacing the fuses ...................... 6-30Replacing the headlight bulb ........6-32Replacing the tail/brake light

bulb ........................................... 6-33Replacing a front turn signal light

bulb ........................................... 6-34


TABLE OF CONTENTSReplacing a rear turn signal light

bulb ...........................................6-34Replacing the license plate light

bulb ...........................................6-35Supporting the motorcycle ............6-36Troubleshooting ............................6-36Troubleshooting charts .................6-37

MOTORCYCLE CARE AND STORAGE ..........................................7-1

Matte color caution .........................7-1Care ................................................7-1Storage ...........................................7-4

SPECIFICATIONS .............................8-1

CONSUMER INFORMATION.............9-1Identification numbers ....................9-1Reporting safety defects .................9-3Motorcycle noise regulation ............9-4Maintenance record ........................9-5YAMAHA MOTOR CORPORATION,

U.S.A. STREET AND ENDURO MOTORCYCLE LIMITED WARRANTY ................................9-7

YAMAHA EXTENDED SERVICE (Y.E.S.) ........................................9-9


1-1

1

SAFETY INFORMATIONEAU10281

MOTORCYCLES ARE SINGLETRACK VEHICLES. THEIR SAFE USEAND OPERATION ARE DEPENDENTUPON THE USE OF PROPER RIDINGTECHNIQUES AS WELL AS THE EX-PERTISE OF THE OPERATOR. EV-ERY OPERATOR SHOULD KNOWTHE FOLLOWING REQUIREMENTSBEFORE RIDING THIS MOTOR-CYCLE.HE OR SHE SHOULD:

� OBTAIN THOROUGH INSTRUC-TIONS FROM A COMPETENTSOURCE ON ALL ASPECTS OFMOTORCYCLE OPERATION.

� OBSERVE THE WARNINGS ANDMAINTENANCE REQUIRE-MENTS IN THE OWNER’S MAN-UAL.

� OBTAIN QUALIFIED TRAININGIN SAFE AND PROPER RIDINGTECHNIQUES.

� OBTAIN PROFESSIONAL TECH-NICAL SERVICE AS INDICATEDBY THE OWNER’S MANUAL

AND/OR WHEN MADE NECES-SARY BY MECHANICAL CONDI-TIONS.

Safe riding� Always make pre-operation

checks. Careful checks may helpprevent an accident.

� This motorcycle is designed to car-ry the operator and a passenger.

� The failure of motorists to detectand recognize motorcycles in traf-fic is the predominating cause ofautomobile/motorcycle accidents.Many accidents have been causedby an automobile driver who didnot see the motorcycle. Makingyourself conspicuous appears tobe very effective in reducing thechance of this type of accident.Therefore:• Wear a brightly colored jacket.• Use extra caution when you are

approaching and passingthrough intersections, since in-tersections are the most likelyplaces for motorcycle accidentsto occur.

• Ride where other motorists cansee you. Avoid riding in anothermotorist’s blind spot.

� Many accidents involve inexperi-enced operators. In fact, many op-erators who have been involved inaccidents do not even have a cur-rent motorcycle license.• Make sure that you are qualified

and that you only lend yourmotorcycle to other qualified op-erators.

• Know your skills and limits.Staying within your limits mayhelp you to avoid an accident.

• We recommend that you prac-tice riding your motorcyclewhere there is no traffic until youhave become thoroughly famil-iar with the motorcycle and all ofits controls.

� Many accidents have been causedby error of the motorcycle opera-tor. A typical error made by the op-erator is veering wide on a turn


SAFETY INFORMATION

1-2

1

due to EXCESSIVE SPEED or un-dercornering (insufficient lean an-gle for the speed).• Always obey the speed limit and

never travel faster than warrant-ed by road and traffic conditions.

• Always signal before turning orchanging lanes. Make sure thatother motorists can see you.

� The posture of the operator andpassenger is important for propercontrol.• The operator should keep both

hands on the handlebar andboth feet on the operator foot-rests during operation to main-tain control of the motorcycle.

• The passenger should alwayshold onto the operator, the seatstrap or grab bar, if equipped,with both hands and keep bothfeet on the passenger footrests.

• Never carry a passenger unlesshe or she can firmly place bothfeet on the passenger footrests.

� Never ride under the influence ofalcohol or other drugs.

� This motorcycle is designed for on-road use only. It is not suitable foroff-road use.

Protective apparelThe majority of fatalities from motor-cycle accidents are the result of headinjuries. The use of a safety helmet isthe single most critical factor in the pre-vention or reduction of head injuries.

� Always wear an approved helmet.� Wear a face shield or goggles.

Wind in your unprotected eyescould contribute to an impairmentof vision that could delay seeing ahazard.

� The use of a jacket, heavy boots,trousers, gloves, etc., is effective inpreventing or reducing abrasionsor lacerations.

� Never wear loose-fitting clothes,otherwise they could catch on thecontrol levers, footrests, or wheelsand cause injury or an accident.

� Never touch the engine or exhaustsystem during or after operation.They become very hot and can

cause burns. Always wear protec-tive clothing that covers your legs,ankles, and feet.

� A passenger should also observethe above precautions.

ModificationsModifications made to this motorcyclenot approved by Yamaha, or the re-moval of original equipment, may ren-der the motorcycle unsafe for use andmay cause severe personal injury.Modifications may also make yourmotorcycle illegal to use.

Loading and accessoriesAdding accessories or cargo to yourmotorcycle can adversely affect stabili-ty and handling if the weight distributionof the motorcycle is changed. To avoidthe possibility of an accident, use ex-treme caution when adding cargo oraccessories to your motorcycle. Useextra care when riding a motorcyclethat has added cargo or accessories.Here are some general guidelines tofollow if loading cargo or adding acces-sories to your motorcycle:


SAFETY INFORMATION

1-3

1

LoadingThe total weight of the operator, pas-senger, accessories and cargo mustnot exceed the maximum load limit.

When loading within this weight limit,keep the following in mind:

� Cargo and accessory weightshould be kept as low and close tothe motorcycle as possible. Makesure to distribute the weight asevenly as possible on both sides ofthe motorcycle to minimize imbal-ance or instability.

� Shifting weights can create a sud-den imbalance. Make sure that ac-cessories and cargo are securelyattached to the motorcycle beforeriding. Check accessory mountsand cargo restraints frequently.

� Never attach any large or heavyitems to the handlebar, front fork,or front fender. These items, in-cluding such cargo as sleeping

bags, duffel bags, or tents, cancreate unstable handling or a slowsteering response.

AccessoriesGenuine Yamaha accessories havebeen specifically designed for use onthis motorcycle. Since Yamaha cannottest all other accessories that may beavailable, you must personally be re-sponsible for the proper selection, in-stallation and use of non-Yamahaaccessories. Use extreme cautionwhen selecting and installing any ac-cessories.Keep the following guidelines in mind,as well as those provided under “Load-ing” when mounting accessories.

� Never install accessories or carrycargo that would impair the perfor-mance of your motorcycle. Care-fully inspect the accessory beforeusing it to make sure that it doesnot in any way reduce groundclearance or cornering clearance,

limit suspension travel, steeringtravel or control operation, or ob-scure lights or reflectors.• Accessories fitted to the handle-

bar or the front fork area cancreate instability due to improperweight distribution or aerody-namic changes. If accessoriesare added to the handlebar orfront fork area, they must be aslightweight as possible andshould be kept to a minimum.

• Bulky or large accessories mayseriously affect the stability ofthe motorcycle due to aerody-namic effects. Wind may at-tempt to lift the motorcycle, orthe motorcycle may become un-stable in cross winds. These ac-cessories may also causeinstability when passing or beingpassed by large vehicles.

• Certain accessories can dis-place the operator from his orher normal riding position. Thisimproper position limits the free-dom of movement of the opera-

Maximum load:190 kg (419 lb)


SAFETY INFORMATION

1-4

1

tor and may limit control ability,therefore, such accessories arenot recommended.

� Use caution when adding electri-cal accessories. If electrical acces-sories exceed the capacity of themotorcycle’s electrical system, anelectric failure could result, whichcould cause a dangerous loss oflights or engine power.

Gasoline and exhaust gas� GASOLINE IS HIGHLY FLAMMA-

BLE:• Always turn the engine off when

refueling.• Take care not to spill any gaso-

line on the engine or exhaustsystem when refueling.

• Never refuel while smoking or inthe vicinity of an open flame.

� Never start the engine or let it runfor any length of time in a closedarea. The exhaust fumes are poi-sonous and may cause loss ofconsciousness and death within ashort time. Always operate yourmotorcycle in an area that has ad-equate ventilation.

� Always turn the engine off beforeleaving the motorcycle unattendedand remove the key from the mainswitch. When parking the motor-cycle, note the following:• The engine and exhaust system

may be hot, therefore, park themotorcycle in a place where pe-destrians or children are not like-ly to touch these hot areas.

• Do not park the motorcycle on aslope or soft ground, otherwise itmay fall over.

• Do not park the motorcycle neara flammable source, (e.g., a ker-osene heater, or near an openflame), otherwise it could catchfire.

� When transporting the motorcyclein another vehicle, make sure thatit is kept upright. If the motorcycleshould lean over, gasoline mayleak out of the fuel tank.

� If you should swallow any gaso-line, inhale a lot of gasoline vapor,or allow gasoline to get into youreyes, see your doctor immediately.If any gasoline spills on your skin

or clothing, immediately wash theaffected area with soap and waterand change your clothes.


SAFETY INFORMATION

1-5

1

EAU10381

Location of important labels Please read the following important labels carefully before operating this vehicle.


SAFETY INFORMATION

1-6

1


SAFETY INFORMATION

1-7

15 6


DESCRIPTION

2-1

2

EAU10410

Left view

1. Front turn signal/position lights (page 6-34)2. Headlight (page 6-32)3. Seat lock (page 3-11)4. Fuel injection system fuse (page 6-30)5. Fuse box (page 6-30)6. Main fuse (page 6-30)7. Helmet holder (page 3-12)8. License plate light (page 6-35)

9. Rear turn signal light (page 6-34)10.Tail/brake light (page 6-33)11.Engine oil level check window (page 6-11)12.Shift pedal (page 3-8)13.Engine oil filler cap (page 6-11)


DESCRIPTION

2-2

2

EAU10420

Right view

1. Sidebag (page 3-12)2. Rear brake fluid reservoir (page 6-22)3. Owner’s tool kit (page 6-1)4. Battery (page 6-29)5. Air filter element (page 6-15)6. Fuel tank cap (page 3-9)7. Front brake fluid reservoir (page 6-22)8. Brake pedal (page 3-9)

9. Rear brake light switch (page 6-21)10.Engine oil filter cartridge (page 6-11)11.Engine oil drain bolt (page 6-11)12.Coolant reservoir (page 6-14)13.Shock absorber assembly spring preload adjusting ring (page 3-13)


DESCRIPTION

2-3

2

EAU10430

Controls and instruments

1. Clutch lever (page 3-8)2. Left handlebar switches (page 3-6)3. Multi-function meter unit (page 3-3)4. Main switch/steering lock (page 3-1)5. Right handlebar switches (page 3-6)6. Throttle grip (page 6-16)7. Brake lever (page 3-8)


INSTRUMENT AND CONTROL FUNCTIONS

3-1

3

EAU10460

Main switch/steering lock

The main switch/steering lock controlsthe ignition and lighting systems, and isused to lock the steering. The variouspositions are described below.

EAU10540

ONAll electrical circuits are supplied withpower, and the meter lighting, taillight,license plate light and position lightscome on, and the engine can be start-ed. The key cannot be removed.

NOTE:The headlight comes on automaticallywhen the engine is started and stays onuntil the key is turned to “OFF”, even ifthe engine stalls.

EAU10660

OFFAll electrical systems are off. The keycan be removed.

EAU10680

LOCKThe steering is locked, and all electricalsystems are off. The key can be re-moved.

To lock the steering

1. Turn the handlebars all the way tothe left.

2. Push the key in from the “OFF” po-sition, and then turn it to “LOCK”while still pushing it.

3. Remove the key.

To unlock the steering

Push the key in, and then turn it to“OFF” while still pushing it.

WARNINGEWA10060

Never turn the key to “OFF” or“LOCK” while the vehicle is moving,otherwise the electrical systems willbe switched off, which may result inloss of control or an accident. Makesure that the vehicle is stopped be-fore turning the key to “OFF” or“LOCK”.

1. Push.2. Turn.

1. Push.2. Turn.



3-2

3

EAU11003

Indicator and warning lights

EAU11020

Turn signal indicator light “ ” This indicator light flashes when theturn signal switch is pushed to the left orright.

EAU11060

Neutral indicator light “ ” This indicator light comes on when thetransmission is in the neutral position.

EAU11080

High beam indicator light “ ” This indicator light comes on when thehigh beam of the headlight is switchedon.

EAU11250

Oil level warning light “ ” This warning light comes on when theengine oil level is low.The electrical circuit of the warning lightcan be checked by turning the key to“ON”.If the warning light does not come onfor a few seconds, then go off, have aYamaha dealer check the electrical cir-cuit.

NOTE:� Even if the oil level is sufficient, the

warning light may flicker whenriding on a slope or during suddenacceleration or deceleration, butthis is not a malfunction.

� This model is also equipped with aself-diagnosis device for the oillevel detection circuit. If the oil lev-el detection circuit is defective, thefollowing cycle will be repeated un-til the malfunction is corrected: The

oil level warning light will flash tentimes, then go off for 2.5 seconds.If this occurs, have a Yamahadealer check the vehicle.

EAU42740

Fuel level warning light “ ” This warning light comes on when thefuel level drops below approximately3.7 L (0.98 US gal) (0.81 Imp.gal).When this occurs, refuel as soon aspossible.The electrical circuit of the warning lightcan be checked by turning the key to“ON”.If the warning light does not come onfor a few seconds, and then go off,have a Yamaha dealer check the elec-trical circuit.

NOTE:� The vehicle must be on a level sur-

face and positioned upright, other-wise the fuel level warning lightmay not come on and go off at theappropriate times.

� This model is also equipped with aself-diagnosis device for the fuellevel detection circuit. If the fuel

1. Neutral indicator light “ ”2. Coolant temperature warning light “ ”3. Engine trouble warning light “ ”4. High beam indicator light “ ”5. Turn signal indicator light “ ”6. Oil level warning light “ ”7. Fuel level warning light “ ”



3-3

3

level detection circuit is defective,the following cycle will be repeateduntil the malfunction is corrected:The fuel level warning light willflash eight times, and then go offfor 3.0 seconds. If this occurs,have a Yamaha dealer check thevehicle.

EAU11440

Coolant temperature warning light “ ” This warning light comes on when theengine overheats. When this occurs,stop the engine immediately and allowthe engine to cool.The electrical circuit of the warning lightcan be checked by turning the key to“ON”.If the warning light does not come onfor a few seconds, then go off, have aYamaha dealer check the electrical cir-cuit.

CAUTION:ECA10020

Do not operate the engine if it isoverheated.

EAU42770

Engine trouble warning light “ ” This warning light comes on when anelectrical circuit monitoring the engineis defective. When this occurs, have aYamaha dealer check the self-diagno-sis system. (See page 3-3 for an expla-nation of the self-diagnosis device.)The electrical circuit of the warning lightcan be checked by turning the key to“ON”. If the warning light does not comeon for a few seconds, then go off, havea Yamaha dealer check the electricalcircuit.

EAU42762

Multi-function meter unit

WARNINGEWA12421

Be sure to stop the vehicle beforemaking any setting changes to themulti-function meter unit.

The multi-function meter unit isequipped with the following:

� a speedometer (which shows theriding speed)

� an odometer (which shows the to-tal distance traveled)

� two tripmeters (which show thedistance traveled since they werelast set to zero)

1. Speedometer2. Odometer/tripmeter/fuel reserve tripme-

ter/clock



3-4

3

� a fuel reserve tripmeter (whichshows the distance traveled on thefuel reserve)

� a clock� a self-diagnosis device� a brightness control mode

NOTE:Be sure to turn the key to “ON” beforeusing the “SELECT” switch “ / ”and “RESET” switch, except for settingthe brightness control mode.

Speedometer

When the key is turned to “ON”, thespeedometer needle will sweep onceacross the speed range and then returnto zero in order to test the electrical cir-cuit.

Odometer, tripmeters, fuel reservetripmeter and clock

Push the “ ” side of the “SELECT”switch to switch the display betweenthe odometer mode “ODO”, the tripme-ter modes “TRIP 1” and “TRIP 2” andthe clock mode in the following order:ODO → TRIP 1 → TRIP 2 → Clock →ODO

NOTE:� Push the “ ” side of the “SE-

LECT” switch to switch the displayin the reverse order.

1. “SELECT” switch “ / ”2. “RESET” switch

1. Speedometer

1. Odometer/tripmeter/fuel reserve tripme-ter/clock



3-5

3

� Push the “RESET” switch for lessthan one second to display theclock for five seconds, regardlessof the currently selected displaymode.

If the fuel level warning light comes on(see page 3-2), the odometer displaywill automatically change to the fuel re-serve tripmeter mode “F-TRIP” andstart counting the distance traveledfrom that point. In that case, push the“ ” side of the “SELECT” switch toswitch the display between the varioustripmeter, odometer, and clock modesin the following order:F-TRIP → TRIP 1 → TRIP 2 → Clock→ ODO → F-TRIP

NOTE:Push the “ ” side of the “SELECT”switch to switch the display in the re-verse order.

To reset a tripmeter, select it by push-ing the “ ” or “ ” side of the “SE-LECT” switch, and then push the“RESET” switch for at least one sec-ond. If you do not reset the fuel reservetripmeter manually, it will reset itself au-

tomatically, and the display will returnto the prior mode after refueling andtraveling 5 km (3 mi).

To set the clock:

1. Push the “ ” or “ ” side of the“SELECT” switch to change thedisplay to the clock mode.

2. Push the “ ” side of the “SE-LECT” switch and the “RESET”switch together for at least twoseconds.

3. When the hour digits start flashing,push the “ ” or “ ” side of the“SELECT” switch to set the hours.

4. Push the “RESET” switch, and theminute digits will start flashing.

5. Push the “ ” or “ ” side of the“SELECT” switch to set the min-utes.

6. Push the “RESET” switch and thenrelease it to start the clock.

Self-diagnosis devicesThis model is equipped with a self-diag-nosis device for various electrical cir-cuits.If any of those circuits are defective, theengine trouble warning light will comeon, and then the odometer/tripme-ter/clock display will indicate a two-digiterror code.If the odometer/tripmeter/clock displayindicates any error codes, note thecode number, and then have a Yamahadealer check the vehicle.

CAUTION:ECA11590

If the display indicates an errorcode, the vehicle should be checkedas soon as possible in order to avoidengine damage.

1. Clock



3-6

3

Brightness control mode

This function allows you to adjust thebrightness of the speedometer panel tosuit the outside lighting conditions.

To set the brightness1. Turn the key to “OFF”.2. Push and hold the “ ” side of the

“SELECT” switch.3. Turn the key to “ON”, and then re-

lease the “SELECT” switch afterfive seconds or more.

4. Push the “ ” or “ ” side of the“SELECT” switch to select the de-sired brightness level.

5. Push the “RESET” switch to con-firm the selected brightness level.The display will return to the odom-eter, tripmeter or clock mode.

EAU12347

Handlebar switches

Left

1. Speedometer panel2. Brightness level

1. Dimmer switch “ / ”2. Turn signal switch “ / ”3. Horn switch “ ”



3-7

3

Right

EAU12400

Dimmer switch “ / ” Set this switch to “ ” for the highbeam and to “ ” for the low beam.

EAU12430

Turn signal switch “ / ” To signal a right-hand turn, push thisswitch to “ ”. To signal a left-handturn, push this switch to “ ”. When re-leased, the switch returns to the centerposition.Since this model is equipped with aself-canceling system, the turn signallights will self-cancel after the vehicle

has traveled both about 150 m (490 ft)and for approximately 15 seconds.However, the turn signal lights can alsobe canceled manually by pushing theswitch in after it has returned to the cen-ter position.

NOTE:The self-canceling system only oper-ates when the vehicle is moving, so thatthe turn signal lights will not self-cancelwhile you are stopped at an intersec-tion.

EAU12500

Horn switch “ ” Press this switch to sound the horn.

EAU12660

Engine stop switch “ / ” Set this switch to “ ” before startingthe engine. Set this switch to “ ” tostop the engine in case of an emergen-cy, such as when the vehicle overturnsor when the throttle cable is stuck.

EAU12710

Start switch “ ” Push this switch to crank the enginewith the starter.

CAUTION:ECA10050

See page 5-1 for starting instruc-tions prior to starting the engine.

EAU41700

The engine trouble warning light willcome on when the key is turned to “ON”and the start switch is pushed, but thisdoes not indicate a malfunction.

EAU42522

“SELECT” switch “ / ” This switch is used to perform selec-tions in the odometer, tripmeter andclock mode of the multi-function meterunit.See “Multi-function meter unit” on page3-3 for detailed information.

EAU42531

“RESET” switch This switch is used to perform selec-tions in the odometer, tripmeter andclock mode of the multi-function meterunit.See “Multi-function meter unit” on page3-3 for detailed information.

1. Engine stop switch “ / ”2. “SELECT” switch “ / ”3. “RESET” switch4. Start switch “ ”



3-8

3

EAU12820

Clutch lever

The clutch lever is located at the lefthandlebar grip. To disengage theclutch, pull the lever toward the handle-bar grip. To engage the clutch, releasethe lever. The lever should be pulledrapidly and released slowly for smoothclutch operation.The clutch lever is equipped with aclutch switch, which is part of the igni-tion circuit cut-off system. (See page3-15.)

EAU12880

Shift pedal

The shift pedal is located on the leftside of the engine and is used in com-bination with the clutch lever whenshifting the gears of the 5-speed con-stant-mesh transmission equipped onthis motorcycle.

NOTE:Use your toes or heel to shift up andyour toes to shift down.

EAU12890

Brake lever

The brake lever is located at the righthandlebar grip. To apply the frontbrake, pull the lever toward the handle-bar grip.

1. Clutch lever 1. Shift pedal 1. Brake lever



3-9

3

EAU12941

Brake pedal

The brake pedal is on the right side ofthe motorcycle. To apply the rearbrake, press down on the brake pedal.

EAU13090

Fuel tank cap

To open the fuel tank capOpen the fuel tank cap lock cover, in-sert the key into the lock, and then turnit 1/8 turn clockwise. The lock will be re-leased and the fuel tank cap can beopened.

To close the fuel tank cap1. Push the fuel tank cap into position

with the key inserted in the lock.2. Turn the key counterclockwise to

the original position, remove it, andthen close the lock cover.

NOTE:The fuel tank cap cannot be closed un-less the key is in the lock. In addition,the key cannot be removed if the cap isnot properly closed and locked.

WARNINGEWA11090

Make sure that the fuel tank cap isproperly closed before riding.

1. Brake pedal 1. Fuel tank cap lock cover2. Unlock.



3-10

3

EAU13220

Fuel

Make sure that there is sufficient fuel inthe tank. When refueling, be sure to in-sert the pump nozzle into the fuel tankfiller hole and to fill the tank to the bot-tom of the filler tube as shown.

WARNINGEWA10880

� Do not overfill the fuel tank, oth-erwise it may overflow when thefuel warms up and expands.

� Avoid spilling fuel on the hot en-gine.

CAUTION:ECA10070

Immediately wipe off spilled fuelwith a clean, dry, soft cloth, sincefuel may deteriorate painted surfac-es or plastic parts.

EAU13361

CAUTION:ECA11400

Use only unleaded gasoline. The useof leaded gasoline will cause severedamage to internal engine parts,such as the valves and piston rings,as well as to the exhaust system.

Your Yamaha engine has been de-signed to use regular unleaded gaso-line with a pump octane number[(R+M)/2] of 86 or higher, or a researchoctane number of 91 or higher. If

knocking (or pinging) occurs, use agasoline of a different brand or premi-um unleaded fuel. Use of unleaded fuelwill extend spark plug life and reducemaintenance costs.GasoholThere are two types of gasohol: gaso-hol containing ethanol and that contain-ing methanol. Gasohol containingethanol can be used if the ethanol con-tent does not exceed 10%. Gasoholcontaining methanol is not recom-mended by Yamaha because it cancause damage to the fuel system or ve-hicle performance problems.

1. Fuel tank filler tube2. Fuel level

Recommended fuel:UNLEADED GASOLINE ONLY

Fuel tank capacity:18.5 L (4.89 US gal) (4.07 Imp.gal)

Fuel reserve amount (when the fuel level warning light comes on):

3.7 L (0.98 US gal) (0.81 Imp.gal)



3-11

3

EAU13431

Catalytic converter This model is equipped with a catalyticconverter in the exhaust system.

WARNINGEWA10860

The exhaust system is hot after op-eration. Make sure that the exhaustsystem has cooled down before do-ing any maintenance work.

CAUTION:ECA10700

The following precautions must beobserved to prevent a fire hazard orother damages.

� Use only unleaded gasoline.The use of leaded gasoline willcause unrepairable damage tothe catalytic converter.

� Never park the vehicle near pos-sible fire hazards such as grassor other materials that easilyburn.

� Do not allow the engine to idletoo long.

EAU42750

Rider seat

To remove the rider seat1. Insert the key into the seat lock,

and then turn it counterclockwise.

2. Lift the front of the seat up, andthen pull the seat off.

To install the rider seat1. Insert the projection on the rear of

the seat into the seat holder asshown.

2. Push the front of the seat down tolock it in place.

3. Remove the key.

NOTE:Make sure that the seat is properly se-cured before riding.

1. Seat lock2. Unlock.

1. Projection2. Seat holder



3-12

3

EAU14320

Helmet holder

The helmet holder is located under therider seat.

To secure a helmet to the helmetholder

1. Remove the rider seat. (See page3-11.)

2. Attach the helmet to the helmetholder, and then securely installthe seat.

WARNINGEWA10160

Never ride with a helmet attached tothe helmet holder, since the helmetmay hit objects, causing loss of con-trol and possibly an accident.

To release the helmet from the hel-met holderRemove the rider seat, remove the hel-met from the helmet holder, and theninstall the seat.

EAU42730

Sidebags

WARNINGEWA14340

Improper loading or overloading cancause loss of control and possiblyan accident or personal injury. Seepages 1-5 and 6-17 for importantloading and tire pressure informa-tion.

� Always securely close the side-bags before riding.

� Distribute weight evenly oneach side of the motorcycle.

� Do not exceed the load limit of 5kg (11 lb) for each sidebag.

� Do not exceed the maximumload of 190 kg (419 lb) for the ve-hicle.

� Do not exceed 120 km/h (80mi/h) when riding with luggagein the sidebags, otherwise han-dling could be affected. Improp-er loading, poor tire or overallmotorcycle conditions, poorroad surfaces or adverse weath-er conditions may make it nec-essary to further reduce theriding speed.

1. Helmet holder



3-13

3

CAUTION:ECA15380

To avoid locking the key in, neverlock either sidebag and remove thekey from the lock before closing thelid.

To open a sidebag lid1. Insert the key into the sidebag

lock, and then turn the key coun-terclockwise.

2. Push the key in, and then fold thesidebag lid up.

To close a sidebag lid1. Fold the sidebag lid down so that

the latch snaps into place.2. Turn the key clockwise, and then

remove it.

NOTE:Water can be harmful to untreatedleather. Use Yamaha Saddle Soap oranother quality brand according to themanufacturer’s directions to clean theleather on the sidebags. Polish the dryleather with a soft cloth, and then treatwith Yamaha Mink Oil or another high-quality leather protectant for increasedwater resistance.

EAU42540

Adjusting the shock absorber assembly

This shock absorber assembly isequipped with a spring preload adjust-ing ring, allowing the spring preload tobe adjusted to suit the rider’s prefer-ence.It is recommended to have a Yamahadealer adjust the spring preload.

CAUTION:ECA10100

Never attempt to turn an adjustingmechanism beyond the maximum orminimum settings.

1. Key2. Unlock.

1. Shock absorber assembly2. Position indicator3. Spring preload adjusting ring



3-14

3

NOTE:� Should you choose to make the

adjustment, use the specialwrench included in the additionaltool kit, which was handed out sep-arately at the purchase of the vehi-cle.

� Align the appropriate notch in theadjusting ring with the position in-dicator on the shock absorber.

WARNINGEWA10220

This shock absorber contains highlypressurized nitrogen gas. For prop-er handling, read and understandthe following information beforehandling the shock absorber. Themanufacturer cannot be held re-

sponsible for property damage orpersonal injury that may result fromimproper handling.

� Do not tamper with or attempt toopen the gas cylinder.

� Do not subject the shock ab-sorber to an open flame or otherhigh heat sources, otherwise itmay explode due to excessivegas pressure.

� Do not deform or damage thegas cylinder in any way, as thiswill result in poor damping per-formance.

� Always have a Yamaha dealerservice the shock absorber.

EAU15301

Sidestand The sidestand is located on the left sideof the frame. Raise the sidestand orlower it with your foot while holding thevehicle upright.

NOTE:The built-in sidestand switch is part ofthe ignition circuit cut-off system, whichcuts the ignition in certain situations.(See further down for an explanation ofthe ignition circuit cut-off system.)

WARNINGEWA10240

The vehicle must not be ridden withthe sidestand down, or if the side-stand cannot be properly moved up(or does not stay up), otherwise thesidestand could contact the groundand distract the operator, resultingin a possible loss of control.Yamaha’s ignition circuit cut-offsystem has been designed to assistthe operator in fulfilling the respon-sibility of raising the sidestand be-fore starting off. Therefore, checkthis system regularly as described

Spring preload setting:Minimum (soft):

1Standard:

4Maximum (hard):

9



3-15

3

below and have a Yamaha dealer re-pair it if it does not function proper-ly.

EAU15312

Ignition circuit cut-off system The ignition circuit cut-off system (com-prising the sidestand switch, clutchswitch and neutral switch) has the fol-lowing functions.

� It prevents starting when the trans-mission is in gear and the side-stand is up, but the clutch lever isnot pulled.

� It prevents starting when the trans-mission is in gear and the clutch le-ver is pulled, but the sidestand isstill down.

� It cuts the running engine when thetransmission is in gear and the sid-estand is moved down.

Periodically check the operation of theignition circuit cut-off system accordingto the following procedure.

WARNINGEWA10250

If a malfunction is noted, have aYamaha dealer check the system be-fore riding.



3-16

3

With the engine turned off:1. Move the sidestand down.2. Make sure that the engine stop switch is turned on.3. Turn the key on. 4. Shift the transmission into the neutral position.5. Push the start switch.Does the engine start?

With the engine still running:6. Move the sidestand up.7. Keep the clutch lever pulled.8. Shift the transmission into gear.9. Move the sidestand down.Does the engine stall?

After the engine has stalled:10. Move the sidestand up.11. Keep the clutch lever pulled.12. Push the start switch.Does the engine start?

The system is OK. The motorcycle can be ridden.

This check is most reliable if performed witha warmed-up engine.

The neutral switch may be defective.The motorcycle should not be ridden untilchecked by a Yamaha dealer.

The sidestand switch may be defective.The motorcycle should not be ridden untilchecked by a Yamaha dealer.

The clutch switch may be defective.The motorcycle should not be ridden untilchecked by a Yamaha dealer.

YES NO

YES NO

YES NO

NOTE:


PRE-OPERATION CHECKS

4-1

4

EAU15593

The condition of a vehicle is the owner’s responsibility. Vital components can start to deteriorate quickly and unexpectedly,even if the vehicle remains unused (for example, as a result of exposure to the elements). Any damage, fluid leakage or lossof tire air pressure could have serious consequences. Therefore, it is very important, in addition to a thorough visual inspec-tion, to check the following points before each ride.

NOTE:Pre-operation checks should be made each time the vehicle is used. Such an inspection can be accomplished in a very shorttime; and the added safety it assures is more than worth the time involved.

WARNINGEWA11150

If any item in the Pre-operation check list is not working properly, have it inspected and repaired before operatingthe vehicle.



4-2

4

EAU15605

Pre-operation check list ITEM CHECKS PAGE

Fuel• Check fuel level in fuel tank.• Refuel if necessary.• Check fuel line for leakage.

3-10

Engine oil• Check oil level in engine.• If necessary, add recommended oil to specified level.• Check vehicle for oil leakage.

6-11

Coolant• Check coolant level in reservoir.• If necessary, add recommended coolant to specified level.• Check cooling system for leakage.

6-14

Front brake

• Check operation.• If soft or spongy, have Yamaha dealer bleed hydraulic system.• Check lever free play.• Adjust if necessary.• Check brake pads for wear.• Replace if necessary.• Check fluid level in reservoir.• If necessary, add recommended brake fluid to specified level.• Check hydraulic system for leakage.

6-20, 6-21, 6-22

Rear brake

• Check operation.• If soft or spongy, have Yamaha dealer bleed hydraulic system.• Check brake pads for wear.• Replace if necessary.• Check fluid level in reservoir.• If necessary, add recommended brake fluid to specified level.• Check hydraulic system for leakage.

6-21, 6-22

Clutch

• Check operation.• Lubricate cable if necessary.• Check lever free play.• Adjust if necessary.

6-20



4-3

4

Throttle grip

• Make sure that operation is smooth.• Check cable free play.• If necessary, have Yamaha dealer adjust cable free play and lubricate cable and

grip housing.

6-16, 6-24

Control cables • Make sure that operation is smooth.• Lubricate if necessary. 6-24

Wheels and tires

• Check for damage.• Check tire condition and tread depth.• Check air pressure.• Correct if necessary.

6-17, 6-19

Brake and shift pedals • Make sure that operation is smooth.• Lubricate pedal pivoting points if necessary. 6-25

Brake and clutch levers • Make sure that operation is smooth.• Lubricate lever pivoting points if necessary. 6-25

Sidestand • Make sure that operation is smooth.• Lubricate pivot if necessary. 6-26

Chassis fasteners • Make sure that all nuts, bolts and screws are properly tightened.• Tighten if necessary. —

Instruments, lights, signals and switches

• Check operation.• Correct if necessary. —

Sidestand switch • Check operation of ignition circuit cut-off system.• If system is defective, have Yamaha dealer check vehicle. 3-14

ITEM CHECKS PAGE


OPERATION AND IMPORTANT RIDING POINTS

5-1

5

EAU15950

WARNINGEWA10270

� Become thoroughly familiarwith all operating controls andtheir functions before riding.Consult a Yamaha dealer re-garding any control or functionthat you do not thoroughly un-derstand.

� Never start the engine or oper-ate it in a closed area for anylength of time. Exhaust fumesare poisonous, and inhalingthem can cause loss of con-sciousness and death within ashort time. Always make surethat there is adequate ventila-tion.

� Before starting out, make surethat the sidestand is up. If thesidestand is not raised com-pletely, it could contact theground and distract the opera-tor, resulting in a possible lossof control.

EAU42420

Starting the engine In order for the ignition circuit cut-offsystem to enable starting, one of thefollowing conditions must be met:

� The transmission is in the neutralposition.

� The transmission is in gear withthe clutch lever pulled and the sid-estand up.

WARNINGEWA10290

� Before starting the engine,check the function of the igni-tion circuit cut-off system ac-cording to the proceduredescribed on page 3-15.

� Never ride with the sidestanddown.

1. Turn the key to “ON” and makesure that the engine stop switch isset to “ ”.

CAUTION:ECA15660

The following warning lights shouldcome on for a few seconds, then gooff.

� Oil level warning light� Fuel level warning light

� Coolant temperature warninglight

� Engine trouble warning lightIf a warning light does not go off, seepage 3-2 for the correspondingwarning light circuit check.

2. Shift the transmission into the neu-tral position.

NOTE:When the transmission is in the neutralposition, the neutral indicator lightshould be on, otherwise have aYamaha dealer check the electrical cir-cuit.

3. Start the engine by pushing thestart switch.

NOTE:If the engine fails to start, release thestart switch, wait a few seconds, andthen try again. Each starting attemptshould be as short as possible to pre-serve the battery. Do not crank the en-gine more than 10 seconds on any oneattempt.



5-2

5

CAUTION:ECA11130

For maximum engine life, alwayswarm the engine up before startingoff. Never accelerate hard when theengine is cold!

NOTE:The engine is warm when it quickly re-sponds to the throttle.

EAU16671

Shifting

Shifting gears lets you control theamount of engine power available forstarting off, accelerating, climbing hills,etc.The gear positions are shown in the il-lustration.

NOTE:To shift the transmission into the neu-tral position, press the shift pedal downrepeatedly until it reaches the end of itstravel, and then slightly raise it.

CAUTION:ECA10260

� Even with the transmission inthe neutral position, do notcoast for long periods of timewith the engine off, and do nottow the motorcycle for long dis-tances. The transmission isproperly lubricated only whenthe engine is running. Inade-quate lubrication may damagethe transmission.

� Always use the clutch whilechanging gears to avoid damag-ing the engine, transmission,and drive train, which are notdesigned to withstand theshock of forced shifting.

EAU16680

To start out and accelerate1. Pull the clutch lever to disengage

the clutch.2. Shift the transmission into first

gear. The neutral indicator lightshould go out.

3. Open the throttle gradually, and atthe same time, release the clutchlever slowly.

1. Shift pedal2. Neutral position



5-3

5

4. At the recommended shift pointsshown in the following table, closethe throttle, and at the same time,quickly pull the clutch lever in.

5. Shift the transmission into secondgear. (Make sure not to shift thetransmission into the neutral posi-tion.)

6. Open the throttle part way andgradually release the clutch lever.

7. Follow the same procedure whenshifting to the next higher gear.

NOTE:Always shift gears at the recommendedshift points.

EAU16700

To decelerate1. Apply both the front and the rear

brakes to slow the motorcycle.2. Shift the transmission into first

gear when the motorcycle reaches25 km/h (16 mi/h). If the engine isabout to stall or runs very roughly,pull the clutch lever in and use thebrakes to stop the motorcycle.

3. Shift the transmission into the neu-tral position when the motorcycleis almost completely stopped. Theneutral indicator light should comeon.

EAU16720

Recommended shift pointsThe recommended shift points duringacceleration and deceleration areshown in the table below.

EAU16841

Engine break-in There is never a more important periodin the life of your engine than the periodbetween 0 and 1600 km (1000 mi). Forthis reason, you should read the follow-ing material carefully.Since the engine is brand new, do notput an excessive load on it for the first1600 km (1000 mi). The various parts inthe engine wear and polish themselvesto the correct operating clearances.During this period, prolonged full-throt-tle operation or any condition that mightresult in engine overheating must beavoided.

EAU17021

0–1000 km (0–600 mi)Avoid prolonged operation above 1/3throttle.1000–1600 km (600–1000 mi)Avoid prolonged operation above 1/2throttle.

Shift up points:1st → 2nd: 20 km/h (13 mi/h)2nd → 3rd: 30 km/h (19 mi/h)3rd → 4th: 40 km/h (25 mi/h)4th → 5th: 50 km/h (31 mi/h)

Shift down points:5th → 4th: 25 km/h (16 mi/h)4th → 3rd: 25 km/h (16 mi/h)3rd → 2nd: 25 km/h (16 mi/h)2nd → 1st: 25 km/h (16 mi/h)



5-4

5

CAUTION:ECA11281

After 1000 km (600 mi) of operation,the engine oil must be changed, andthe oil filter cartridge or element re-placed.

1600 km (1000 mi) and beyondThe vehicle can now be operated nor-mally.

CAUTION:ECA10270

If any engine trouble should occurduring the engine break-in period,immediately have a Yamaha dealercheck the vehicle.

EAU17212

Parking When parking, stop the engine, andthen remove the key from the mainswitch.

WARNINGEWA10310

� Since the engine and exhaustsystem can become very hot,park in a place where pedestri-ans or children are not likely totouch them.

� Do not park on a slope or on softground, otherwise the vehiclemay overturn.

CAUTION:ECA10380

Never park in an area where thereare fire hazards such as grass orother flammable materials.


PERIODIC MAINTENANCE AND MINOR REPAIR

6-1

6

EAU17231

Safety is an obligation of the owner. Pe-riodic inspection, adjustment and lubri-cation will keep your vehicle in thesafest and most efficient condition pos-sible. The most important points ofmotorcycle inspection, adjustment, andlubrication are explained on the follow-ing pages.Maintenance, replacement, or repairof the emission control devices andsystems may be performed by anyrepair establishment or individualthat is certified (if applicable).

WARNINGEWA10320

If you are not familiar with mainte-nance work, have a Yamaha dealerdo it for you.

EAU17301

PERIODIC MAINTENANCE PROPER PERIODIC MAINTENANCEOF YOUR VEHICLE IS IMPORTANTIN ORDER TO ENJOY LONG, PLEA-SURABLE SERVICE. ESPECIALLYIMPORTANT ARE THE MAINTE-NANCE SERVICES RELATED TOEMISSIONS CONTROL. THESECONTROLS NOT ONLY FUNCTIONTO ENSURE CLEANER AIR, BUTARE ALSO VITAL TO PROPER EN-GINE OPERATION AND MAXIMUMPERFORMANCE. IN THE FOLLOW-ING PERIODIC MAINTENANCECHARTS, THE SERVICES RELATEDTO EMISSIONS CONTROL AREGROUPED SEPARATELY. THESESERVICES REQUIRE SPECIALIZEDDATA, KNOWLEDGE, AND EQUIP-MENT. YAMAHA DEALERS ARETRAINED AND EQUIPPED TO PER-FORM THESE PARTICULAR SER-VICES.

EAU17350

Owner’s tool kit

The owner’s tool kit is located under therider seat. (See page 3-11.)The service information included in thismanual and the tools provided in theowner’s tool kit are intended to assistyou in the performance of preventivemaintenance and minor repairs. How-ever, additional tools such as a torquewrench may be necessary to performcertain maintenance work correctly.

NOTE:If you do not have the tools or experi-ence required for a particular job, havea Yamaha dealer perform it for you.

1. Owner’s tool kit



6-2

6

WARNINGEWA10340

Modifications not approved byYamaha may cause loss of perfor-mance, excessive emissions, andrender the vehicle unsafe for use.Consult a Yamaha dealer before at-tempting any changes.



6-3

6

EAU17600

Periodic maintenance chart for the emission control system

* Since these items require special tools, data and technical skills, have a Yamaha dealer perform the service.

No. ITEM ROUTINE

INITIAL ODOMETER READINGS

600 mi (1000 km)

or 1 month

4000 mi (7000 km)

or 6 months

8000 mi (13000 km)

or 12 months

12000 mi (19000 km)

or 18 months

16000 mi (25000 km)

or 24 months

20000 mi (31000 km)

or 30 months

1 * Fuel line• Check fuel hoses for cracks or

damage.• Replace if necessary.

√ √ √ √ √

2 Spark plugs

• Check condition.• Adjust gap and clean.• Replace every 8000 mi (13000

km) or 12 months.

√ Replace. √ Replace. √

3 * Valve clearance • Check and adjust valve clearance when engine is cold. √ √ √ √ √ √

4 * Crankcase breather system

• Check breather hose for cracks or damage.

• Replace if necessary.√ √ √ √ √

5 * Fuel injection • Adjust synchronization. √ √ √ √ √

6 * Exhaust system• Check for leakage.• Tighten if necessary.• Replace gasket(s) if necessary.

√ √ √ √ √

7 *Evaporative emis-sion control system (For California only)

• Check control system for dam-age.

• Replace if necessary.√



6-4

6

EAU32185

General maintenance and lubrication chart

No. ITEM ROUTINE


600 mi (1000 km)

or 1 month

4000 mi (7000 km)

or 6 months

8000 mi (13000 km)

or 12 months

12000 mi (19000 km)

or 18 months

16000 mi (25000 km)

or 24 months

20000 mi (31000 km)

or 30 months

1 * Air filter element • Check condition and damage.• Replace if necessary. √ √ √ √ √

2 * Clutch • Check operation.• Adjust or replace cable. √ √ √ √ √ √

3 * Front brake

• Check operation, fluid level, and for fluid leakage.

• Adjust brake lever free play and replace brake pads if necessary.

√ √ √ √ √ √

4 * Rear brake• Check operation, fluid level, and

for fluid leakage.• Replace brake pads if necessary.

√ √ √ √ √ √

5 * Brake hoses• Check for cracks or damage. √ √ √ √ √

• Replace. Every 4 years

6 * Wheels • Check runout and for damage.• Replace if necessary. √ √ √ √ √

7 * Tires

• Check tread depth and for dam-age.

• Replace if necessary.• Check air pressure.• Correct if necessary.

√ √ √ √ √

8 * Wheel bearings• Check bearings for smooth oper-

ation.• Replace if necessary.

√ √ √ √ √



6-5

6

9 * Swingarm pivot bearings

• Check bearing assemblies for looseness.

• Moderately repack with lithium-soap-based grease.

√ Repack.

10 * Drive belt • Check belt tension.• Adjust if necessary. √ Every 2500 mi (4000 km)

11 * Steering bearings

• Check bearing assemblies for looseness.

• Moderately repack with lithium-soap-based grease every 16000 mi (25000 km) or 24 months.

√ √ √ √ Repack. √

12 * Chassis fasteners• Check all chassis fitting and fas-

teners.• Correct if necessary.

√ √ √ √ √

13 Brake lever pivot shaft • Apply silicone grease lightly. √ √ √ √ √

14 Brake pedal pivot shaft • Apply silicone grease lightly. √ √ √ √ √

15 Clutch lever pivot shaft

• Apply lithium-soap-based grease (all-purpose grease) lightly. √ √ √ √ √

16 Shift pedal pivot shaft

• Apply lithium-soap-based grease (all-purpose grease) lightly. √ √ √ √ √

17 Sidestand pivot• Check operation.• Apply lithium-soap-based grease

(all-purpose grease) lightly.√ √ √ √ √

No. ITEM ROUTINE


600 mi (1000 km)

or 1 month

4000 mi (7000 km)

or 6 months

8000 mi (13000 km)

or 12 months

12000 mi (19000 km)

or 18 months

16000 mi (25000 km)

or 24 months

20000 mi (31000 km)

or 30 months



6-6

6

18 * Sidestand switch • Check operation and replace if necessary. √ √ √ √ √ √

19 * Front fork• Check operation and for oil leak-

age.• Replace if necessary.

√ √ √ √ √

20 * Shock absorber as-sembly

• Check operation and for oil leak-age.


21 * Rear suspension link pivots

• Apply lithium-soap-based grease lightly. √

22 Engine oil • Change (warm engine before draining). √ √ √ √ √ √

23 * Engine oil filter car-tridge • Replace. √ √ √

24 * Cooling system

• Check hoses for cracks or dam-age.


• Change with ethylene glycol anti-freeze coolant every 24 months. Change.

25 * Front and rear brake switches • Check operation. √ √ √ √ √ √

26 * Control cables• Apply Yamaha chain and cable

lube or engine oil SAE 10W-30 thoroughly.

√ √ √ √ √ √

No. ITEM ROUTINE


600 mi (1000 km)

or 1 month

4000 mi (7000 km)

or 6 months

8000 mi (13000 km)

or 12 months

12000 mi (19000 km)

or 18 months

16000 mi (25000 km)

or 24 months

20000 mi (31000 km)

or 30 months



6-7

6

* Since these items require special tools, data and technical skills, have a Yamaha dealer perform the service.

NOTE:From 24000 mi (37000 km) or 36 months, repeat the maintenance intervals starting from 8000 mi (13000 km) or 12 months.

EAU17650

NOTE:� Air filter

• This model’s air filter is equipped with a disposable oil-coated paper element, which must not be cleaned with com-pressed air to avoid damaging it.

• The air filter element needs to be replaced more frequently when riding in unusually wet or dusty areas.� Hydraulic brake service

• After disassembling the brake master cylinders and calipers, always change the fluid. Regularly check the brake fluidlevels and fill the reservoirs as required.

• Every two years replace the internal components of the brake master cylinders and calipers, and change the brakefluid.

27 * Throttle grip hous-ing and cable

• Check operation and free play.• Adjust the throttle cable free play

if necessary.• Lubricate the throttle grip housing

and cable.

√ √ √ √ √

28 * Lights, signals and switches

• Check operation.• Adjust headlight beam. √ √ √ √ √ √

No. ITEM ROUTINE


600 mi (1000 km)

or 1 month

4000 mi (7000 km)

or 6 months

8000 mi (13000 km)

or 12 months

12000 mi (19000 km)

or 18 months

16000 mi (25000 km)

or 24 months

20000 mi (31000 km)

or 30 months



6-8

6

• Replace the brake hoses every four years and if cracked or damaged.



6-9

6

EAU18751

Removing and installing the panel The panel shown needs to be removedto perform some of the maintenancejobs described in this chapter. Refer tothis section each time the panel needsto be removed and installed.

EAU19193

Panel A

To remove the panelRemove the bolts, and then take thepanel off.

To install the panelPlace the panel in the original position,and then install the bolts.

EAU42430

Checking the spark plugs The spark plugs are important enginecomponents, which are easy to check.Since heat and deposits will cause anyspark plug to slowly erode, the sparkplugs should be removed and checkedin accordance with the periodic mainte-nance and lubrication chart. In addition,the condition of the spark plugs can re-veal the condition of the engine.

To remove a spark plug1. Remove the appropriate spark

plug cover (rear right or front left)by removing the bolts.

2. Remove the spark plug cap.

1. Panel A

1. Panel A2. Bolt

1. Spark plug cover2. Bolt



6-10

6

3. Remove the spark plug as shown,with the spark plug wrench includ-ed in the additional tool kit, whichwas handed out separately at thepurchase of the vehicle.

To check the spark plugs1. Check that the porcelain insulator

around the center electrode oneach spark plug is a medium-to-light tan (the ideal color when thevehicle is ridden normally).

2. Check that all spark plugs installedin the engine have the same color.

NOTE:If any spark plug shows a distinctly dif-ferent color, the engine could be oper-ating improperly. Do not attempt to

diagnose such problems yourself. In-stead, have a Yamaha dealer checkthe vehicle.

3. Check each spark plug for elec-trode erosion and excessive car-bon or other deposits, and replaceit if necessary.

To install a spark plug1. Measure the spark plug gap with a

wire thickness gauge and, if nec-essary, adjust the gap to specifica-tion.

2. Clean the surface of the spark pluggasket and its mating surface, andthen wipe off any grime from thespark plug threads.

3. Install the spark plug with thespark plug wrench, and then tight-en it to the specified torque.

NOTE:If a torque wrench is not available wheninstalling a spark plug, a good estimateof the correct torque is 1/4–1/2 turnpast finger tight. However, the sparkplug should be tightened to the speci-fied torque as soon as possible.

4. Install the spark plug cap.5. Install the spark plug cover by in-

stalling the bolts.

1. Spark plug wrench

Specified spark plug:NGK/LMAR7A-9

1. Spark plug gap

Spark plug gap:0.8–0.9 mm (0.031–0.035 in)

Tightening torque:Spark plug:

12.5 Nm (1.25 m·kgf, 9.0 ft·lbf)



6-11

6

EAU19681

Canister (for California only)

This model is equipped with a canisterto prevent the discharging of fuel vaporinto the atmosphere. Before operatingthis vehicle, make sure to check the fol-lowing:

� Check each hose connection.� Check each hose and canister for

cracks or damage. Replace if dam-aged.

� Make sure that the canister breath-er is not blocked, and if necessary,clean it.

EAU42591

Engine oil and oil filter car-tridge The engine oil level should be checkedbefore each ride. In addition, the oilmust be changed and the oil filter car-tridge replaced at the intervals speci-fied in the periodic maintenance andlubrication chart.

To check the engine oil level1. Place the vehicle on a level sur-

face and hold it in an upright posi-tion.

NOTE:Make sure that the vehicle is positionedstraight up when checking the oil level.A slight tilt to the side can result in afalse reading.

2. Start the engine, warm it up forseveral minutes, and then turn itoff.

3. Wait a few minutes until the oil set-tles, and then check the oil levelthrough the check window locatedat the bottom-left side of the crank-case.

NOTE:The engine oil should be between theminimum and maximum level marks.

4. If the engine oil is below the mini-mum level mark, add sufficient oilof the recommended type to raiseit to the correct level.

To change the engine oil (with orwithout oil filter cartridge replace-ment)

1. Start the engine, warm it up forseveral minutes, and then turn itoff.

1. Engine oil filler cap2. Engine oil level check window3. Maximum level mark4. Minimum level mark



6-12

6

2. Place an oil pan under the engineto collect the used oil.

3. Remove the engine oil filler capand drain bolt to drain the oil fromthe crankcase.

NOTE:Skip steps 4–6 if the oil filter cartridge isnot being replaced.

4. Remove the oil filter cartridge withan oil filter wrench.

NOTE:An oil filter wrench is available at aYamaha dealer.

5. Apply a thin coat of engine oil tothe O-ring of the new oil filter car-tridge.

NOTE:Make sure that the O-ring is properlyseated.

6. Install the new oil filter cartridgewith an oil filter wrench, and thentighten it to the specified torquewith a torque wrench.

1. Engine oil drain bolt

1. Oil filter cartridge2. Oil filter wrench

1. O-ring



6-13

6 7. Install the engine oil drain bolt, andthen tighten it to the specifiedtorque.

8. Add the specified amount of therecommended engine oil, and theninstall and tighten the oil filler cap.

NOTE:Be sure to wipe off spilled oil on anyparts after the engine and exhaust sys-tem have cooled down.

CAUTION:ECA11620

� In order to prevent clutch slip-page (since the engine oil alsolubricates the clutch), do notmix any chemical additives. Donot use oils with a diesel speci-fication of “CD” or oils of a high-er quality than specified. Inaddition, do not use oils labeled“ENERGY CONSERVING II” orhigher.

� Make sure that no foreign mate-rial enters the crankcase.

9. Start the engine, and then let it idlefor several minutes while checkingit for oil leakage. If oil is leaking, im-mediately turn the engine off andcheck for the cause.

NOTE:After the engine is started, the engineoil level warning light should go off if theoil level is sufficient.

CAUTION:ECA10400

If the oil level warning light flickersor remains on, immediately turn theengine off and have a Yamaha dealercheck the vehicle.

10. Turn the engine off, and thencheck the oil level and correct it ifnecessary.

1. Torque wrench

Tightening torque:Oil filter cartridge:

17 Nm (1.7 m·kgf, 12 ft·lbf)

Tightening torque:Engine oil drain bolt:

43 Nm (4.3 m·kgf, 31 ft·lbf)

Recommended engine oil:See page 8-1.

Oil quantity:Without oil filter cartridge replace-ment:

3.20 L (3.38 US qt) (2.82 Imp.qt)With oil filter cartridge replacement:

3.40 L (3.59 US qt) (2.99 Imp.qt)



6-14

6

EAU20070

Coolant The coolant level should be checkedbefore each ride. In addition, the cool-ant must be changed at the intervalsspecified in the periodic maintenanceand lubrication chart.

EAU42630

To check the coolant level1. Place the vehicle on a level sur-


NOTE:� The coolant level must be checked

on a cold engine since the levelvaries with engine temperature.

� Make sure that the vehicle is posi-tioned straight up when checkingthe coolant level. A slight tilt to theside can result in a false reading.

2. Check the coolant level in the cool-ant reservoir.

NOTE:The coolant should be between theminimum and maximum level marks.

3. If the coolant is at or below theminimum level mark, remove pan-el A. (See page 6-9.)

4. Remove the reservoir cap, addcoolant to the maximum levelmark, and then install the reservoircap.

CAUTION:ECA10471

� If coolant is not available, usedistilled water or soft tap waterinstead. Do not use hard wateror salt water since it is harmfulto the engine.

� If water has been used insteadof coolant, replace it with cool-ant as soon as possible, other-wise the cooling system will notbe protected against frost andcorrosion.

1. Coolant reservoir2. Maximum level mark3. Minimum level mark

1. Coolant reservoir cap

Coolant reservoir capacity (up to the maximum level mark):

0.45 L (0.48 US qt) (0.40 Imp.qt)



6-15

6

� If water has been added to thecoolant, have a Yamaha dealercheck the antifreeze content ofthe coolant as soon as possible,otherwise the effectiveness ofthe coolant will be reduced.

WARNINGEWA10380

Never attempt to remove the radiatorcap when the engine is hot.

5. Install the panel.

NOTE:� The radiator fan is automatically

switched on or off according to thecoolant temperature in the radia-tor.

� If the engine overheats, see page6-37 for further instructions.

� Make sure that the coolant reser-voir breather hose is properly rout-ed through the guide.

EAU33030

Changing the coolant

WARNINGEWA10380

Never attempt to remove the radiatorcap when the engine is hot.

The coolant must be changed at the in-tervals specified in the periodic mainte-nance and lubrication chart. Have aYamaha dealer change the coolant.

EAU42441

Replacing the air filter element The air filter element should be re-placed at the intervals specified in theperiodic maintenance and lubricationchart. Replace the air filter elementmore frequently if you are riding in un-usually wet or dusty areas.

1. Remove the air filter case cover byremoving the bolts.

2. Pull the air filter element out.

1. Guide2. Coolant reservoir breather hose

1. Air filter case cover2. Bolt



6-16

6

3. Insert a new air filter element intothe air filter case.

CAUTION:ECA10480

� Make sure that the air filter ele-ment is properly seated in theair filter case.

� The engine should never be op-erated without the air filter ele-ment installed, otherwise thepiston(s) and/or cylinder(s) maybecome excessively worn.

4. Install the air filter case cover by in-stalling the bolts.

EAU21382

Checking the throttle cable free play

The throttle cable free play should mea-sure 4.0–6.0 mm (0.16–0.24 in) at thethrottle grip. Periodically check thethrottle cable free play and, if neces-sary, have a Yamaha dealer adjust it.

EAU21401

Valve clearance The valve clearance changes with use,resulting in improper air-fuel mixtureand/or engine noise. To prevent thisfrom occurring, the valve clearancemust be adjusted by a Yamaha dealerat the intervals specified in the periodicmaintenance and lubrication chart.

1. Air filter element

1. Throttle cable free play



6-17

6

EAU42710

Tires To ensure maximum performance,long service, and safe operation, notethe following:

Tire air pressureAlways check and adjust the tire pres-sure before operating the motorcycle.

WARNINGEWA14650

Tire inflation pressure should bechecked and adjusted when the tem-perature of the tire equals the ambi-ent air temperature. Tire inflationpressure must be adjusted accord-ing to total weight of cargo, rider,passenger, and accessories (wind-shield, sidebags, etc. if approved forthis model).

WARNINGEWA11020

Because loading has an enormousimpact on the handling, braking,performance and safety characteris-tics of your motorcycle, you shouldkeep the following precautions inmind.

� NEVER OVERLOAD THEMOTORCYCLE! Operation of anoverloaded motorcycle may re-sult in tire damage, loss of con-trol, or severe injury. Make surethat the total weight of rider,

passenger, cargo, and accesso-ries does not exceed the speci-fied maximum load for thevehicle.

� Do not carry along looselypacked items, which can shiftduring a ride.

� Securely pack the heaviestitems close to the center of themotorcycle and distribute theweight evenly on both sides.

� Adjust the suspension and tireair pressure with regard to theload.

� Check the tire condition and airpressure before each ride.

Tire air pressure (measured on cold tires):

0–90 kg (0–198 lb):Front:

250 kPa (36 psi) (2.50 kgf/cm²)Rear:

280 kPa (41 psi) (2.80 kgf/cm²)90–190 kg (198–419 lb):

Front:250 kPa (36 psi) (2.50 kgf/cm²)

Rear:280 kPa (41 psi) (2.80 kgf/cm²)

Maximum load*:190 kg (419 lb)

* Total weight of rider, passenger, car-go and accessories



6-18

6

Tire inspection

Always check the tires before operatingthe motorcycle. If a tire tread showscrosswise line (minimum tread depth),if the tire has a nail or glass fragmentsin it, or if the sidewall is cracked, con-tact a Yamaha dealer immediately andhave the tire replaced.

NOTE:These limits may be different by regula-tion from country to country. If so, con-form to the limits specified by theregulations of your own country.

WARNINGEWA10580

� It is dangerous to ride with aworn-out tire. When a tire treadbegins to show crosswise lines,have a Yamaha dealer replacethe tire immediately.

� The replacement of all wheel-and brake-related parts, includ-ing the tires, should be left to aYamaha dealer, who has thenecessary professional knowl-edge and experience.

Tire informationThis motorcycle is equipped with castwheels and tubeless tires.

WARNINGEWA10460

� The front and rear tires shouldbe of the same make and de-sign, otherwise the handlingcharacteristics of the vehiclecannot be guaranteed.

� After extensive tests, only thetires listed below have been ap-proved for this model byYamaha Motor Co., Ltd.1. Tire sidewall

2. Tire wear indicator3. Tire tread depth

Minimum tire tread depth (front and rear):

1.0 mm (0.04 in)

Front tire:Size:

130/90 16M/C 67HManufacturer/model:

DUNLOP/D404F XBRIDGESTONE/EXEDRA G721

Rear tire:Size:

170/70B 16M/C 75HManufacturer/model:

DUNLOP/K555BRIDGESTONE/EXEDRA G722 G



6-19

6

EAU21960

Cast wheels To maximize the performance, durabil-ity, and safe operation of your vehicle,note the following points regarding thespecified wheels.

� The wheel rims should be checkedfor cracks, bends or warpage be-fore each ride. If any damage isfound, have a Yamaha dealer re-place the wheel. Do not attempteven the smallest repair to thewheel. A deformed or crackedwheel must be replaced.

� The wheel should be balancedwhenever either the tire or wheelhas been changed or replaced. Anunbalanced wheel can result inpoor performance, adverse han-dling characteristics, and a short-ened tire life.

� Ride at moderate speeds afterchanging a tire since the tire sur-face must first be “broken in” for itto develop its optimal characteris-tics.

EAU22011

Accessories and replacement parts

WARNINGEWA10621

This vehicle is not designed to pull atrailer or to be attached to a sidecar.The accessories or replacementparts you choose for your vehicleshould be designed specifically forthis model, and they must be se-curely mounted to maintain the in-herent stability of the originaldesign. Genuine Yamaha Parts andAccessories are designed and test-ed to be compatible with your vehi-cle. Please consider GenuineYamaha Parts and Accessories be-fore making a purchase. Use of non-Yamaha-approved accessories orreplacement parts may cause loss ofhandling stability and riding safety.Since Yamaha cannot control thequality of accessories or parts man-ufactured by other companies,Yamaha cannot be held liable for

any consequences caused by theuse of items which have not beenapproved by Yamaha.



6-20

6

EAU22031

Adjusting the clutch lever free play

The clutch lever free play should mea-sure 5.0–10.0 mm (0.20–0.39 in) asshown. Periodically check the clutch le-ver free play and, if necessary, adjust itas follows.

1. Loosen the locknut at the clutch le-ver.

2. To increase the clutch lever freeplay, turn the adjusting bolt in di-rection (a). To decrease the clutchlever free play, turn the adjustingbolt in direction (b).

3. If the specified clutch lever freeplay could be obtained as de-scribed above, tighten the locknutand skip the rest of the procedure,otherwise, proceed as follows.

4. Fully turn the adjusting bolt in di-rection (a) to loosen the clutch ca-ble.

5. Loosen the locknut further downthe clutch cable.

6. To increase the clutch lever freeplay, turn the adjusting nut in direc-tion (a). To decrease the clutch le-ver free play, turn the adjusting nutin direction (b).

7. Tighten both locknuts.

EAU22092

Adjusting the brake lever free play

The brake lever free play should mea-sure 2.0–5.0 mm (0.08–0.20 in) asshown. Periodically check the brake le-ver free play and, if necessary, adjust itas follows.

1. Loosen the locknut at the brake le-ver.

2. To increase the brake lever freeplay, turn the adjusting screw in di-rection (a). To decrease the brakelever free play, turn the adjustingscrew in direction (b).

3. Tighten the locknut.

1. Locknut (clutch lever)2. Clutch lever free play adjusting bolt3. Clutch lever free play

1. Clutch lever free play adjusting nut (clutch cable)

2. Locknut (clutch cable)

1 2

(a)

(b) 1. Locknut2. Brake lever free play adjusting screw3. Brake lever free play



6-21

6

WARNINGEWA10630

� After adjusting the brake leverfree play, check the free playand make sure that the brake isworking properly.

� A soft or spongy feeling in thebrake lever can indicate thepresence of air in the hydraulicsystem. If there is air in the hy-draulic system, have a Yamahadealer bleed the system beforeoperating the motorcycle. Air inthe hydraulic system will dimin-ish the braking performance,which may result in loss of con-trol and an accident.

EAU22270

Adjusting the rear brake light switch

The rear brake light switch, which is ac-tivated by the brake pedal, is properlyadjusted when the brake light comeson just before braking takes effect. Ifnecessary, adjust the brake light switchas follows.Turn the adjusting nut while holding therear brake light switch in place. Tomake the brake light come on earlier,turn the adjusting nut in direction (a). Tomake the brake light come on later, turnthe adjusting nut in direction (b).

EAU22390

Checking the front and rear brake pads The front and rear brake pads must bechecked for wear at the intervals spec-ified in the periodic maintenance andlubrication chart.

EAU22430

Front brake pads

Each front brake pad is provided withwear indicator grooves, which allowyou to check the brake pad wear with-out having to disassemble the brake.To check the brake pad wear, checkthe wear indicator grooves. If a brakepad has worn to the point that the wear

1. Rear brake light switch2. Rear brake light switch adjusting nut

1. Brake pad wear indicator groove



6-22

6

indicator grooves have almost disap-peared, have a Yamaha dealer replacethe brake pads as a set.

EAU22500

Rear brake pads

Check each rear brake pad for damageand measure the lining thickness. If abrake pad is damaged or if the liningthickness is less than 0.8 mm (0.03 in),have a Yamaha dealer replace thebrake pads as a set.

EAU22580

Checking the brake fluid level

Front brake

Rear brake

Insufficient brake fluid may allow air toenter the brake system, possibly caus-ing it to become ineffective.

Before riding, check that the brake fluidis above the minimum level mark andreplenish if necessary. A low brake fluidlevel may indicate worn brake padsand/or brake system leakage. If thebrake fluid level is low, be sure to checkthe brake pads for wear and the brakesystem for leakage.Observe these precautions:

� When checking the fluid level,make sure that the top of the brakefluid reservoir is level.

� Use only the recommended qualitybrake fluid, otherwise the rubberseals may deteriorate, causingleakage and poor braking perfor-mance.

� Refill with the same type of brakefluid. Mixing fluids may result in aharmful chemical reaction andlead to poor braking performance.

1. Lining thickness

1. Minimum level mark

1. Minimum level mark

Recommended brake fluid:DOT 4



6-23

6

� Be careful that water does not en-ter the brake fluid reservoir whenrefilling. Water will significantlylower the boiling point of the fluidand may result in vapor lock.

� Brake fluid may deteriorate paint-ed surfaces or plastic parts. Al-ways clean up spilled fluidimmediately.

� As the brake pads wear, it is nor-mal for the brake fluid level to grad-ually go down. However, if thebrake fluid level goes down sud-denly, have a Yamaha dealercheck the cause.

EAU22730

Changing the brake fluid Have a Yamaha dealer change thebrake fluid at the intervals specified inthe NOTE after the periodic mainte-nance and lubrication chart. In addition,have the oil seals of the master cylin-ders and calipers as well as the brakehoses replaced at the intervals listedbelow or whenever they are damagedor leaking.

� Oil seals: Replace every twoyears.

� Brake hoses: Replace every fouryears.

EAU23040

Drive belt slack The drive belt slack should be checkedand adjusted at the intervals specifiedin the periodic maintenance and lubri-cation chart.

EAU38410

To check the drive belt slack1. Place the vehicle on the sidestand.2. Note the current position of the

drive belt using the marks near thedrive belt check hole.

NOTE:The marks near the drive belt checkhole are 5.0 mm (0.2 in) apart.

1. Drive belt2. Marks3. Drive belt slack



6-24

6

3. Note the position of the drive beltwith a force of 45 N (4.5 kgf, 10 lbf)applied to the belt with a belt ten-sion gauge as shown.

NOTE:A belt tension gauge is available at aYamaha dealer.

4. Calculate the drive belt slack bysubtracting the measurement not-ed in step 2 from the measurementnoted in step 3.

5. If the drive belt slack is incorrect,have a Yamaha dealer adjust it.

EAU23091

Checking and lubricating the cables The operation of all control cables andthe condition of the cables should bechecked before each ride, and the ca-bles and cable ends should be lubricat-ed if necessary. If a cable is damagedor does not move smoothly, have aYamaha dealer check or replace it.

WARNINGEWA10710

Damage to the outer housing of ca-bles may result in internal rustingand cause interference with cablemovement. Replace damaged ca-bles as soon as possible to preventunsafe conditions.

EAU23111

Checking and lubricating the throttle grip and cable The operation of the throttle grip shouldbe checked before each ride. In addi-tion, the cable should be lubricated atthe intervals specified in the periodicmaintenance chart.

1. Belt tension gauge

Drive belt slack:5.0–7.0 mm (0.20–0.28 in)

Recommended lubricant:Yamaha Chain and Cable Lube or engine oil SAE 10W-30



6-25

6

EAU23132

Checking and lubricating the brake and shift pedals

The operation of the brake and shiftpedals should be checked before eachride, and the pedal pivots should be lu-bricated if necessary.

EAU23141

Checking and lubricating the brake and clutch levers

Brake lever

Clutch lever

The operation of the brake and clutchlevers should be checked before eachride, and the lever pivots should be lu-bricated if necessary.

Recommended lubricants:Brake pedal:

Silicone greaseShift pedal:

Lithium-soap-based grease (all-purpose grease)



6-26

6

EAU23200

Checking and lubricating the sidestand

The operation of the sidestand shouldbe checked before each ride, and thesidestand pivot and metal-to-metalcontact surfaces should be lubricated ifnecessary.

WARNINGEWA10730

If the sidestand does not move upand down smoothly, have a Yamahadealer check or repair it.

EAUM1650

Lubricating the swingarm piv-ots

The swingarm pivots must be lubricat-ed at the intervals specified in the peri-odic maintenance and lubrication chart.

Recommended lubricants:Brake lever:

Silicone greaseClutch lever:

Lithium-soap-based grease (all-purpose grease)

Recommended lubricant:Lithium-soap-based grease (all-pur-pose grease)

Recommended lubricant:Lithium-soap-based grease



6-27

6

EAU23250

Lubricating the rear suspen-sion

The pivoting points of the rear suspen-sion must be lubricated at the intervalsspecified in the periodic maintenanceand lubrication chart.

EAU23271

Checking the front fork The condition and operation of the frontfork must be checked as follows at theintervals specified in the periodic main-tenance and lubrication chart.

To check the condition

WARNINGEWA10750

Securely support the vehicle so thatthere is no danger of it falling over.

Check the inner tubes for scratches,damage and excessive oil leakage.

To check the operation1. Place the vehicle on a level sur-


2. While applying the front brake,push down hard on the handlebarsseveral times to check if the frontfork compresses and reboundssmoothly.

CAUTION:ECA10590

If any damage is found or the frontfork does not operate smoothly,have a Yamaha dealer check or re-pair it.

Recommended lubricant:Lithium-soap-based grease



6-28

6

EAU23280

Checking the steering Worn or loose steering bearings maycause danger. Therefore, the operationof the steering must be checked as fol-lows at the intervals specified in the pe-riodic maintenance and lubricationchart.

1. Place a stand under the engine toraise the front wheel off theground.

WARNINGEWA10750

Securely support the vehicle so thatthere is no danger of it falling over.

2. Hold the lower ends of the frontfork legs and try to move them for-ward and backward. If any freeplay can be felt, have a Yamahadealer check or repair the steering.

EAU23290

Checking the wheel bearings The front and rear wheel bearings mustbe checked at the intervals specified inthe periodic maintenance and lubrica-tion chart. If there is play in the wheelhub or if the wheel does not turnsmoothly, have a Yamaha dealer checkthe wheel bearings.



6-29

6

EAU23370

Battery

This model is equipped with a sealed-type (MF) battery, which does not re-quire any maintenance. There is noneed to check the electrolyte or to adddistilled water.

CAUTION:ECA10620

Never attempt to remove the batterycell seals, as this would permanent-ly damage the battery.

WARNINGEWA10760

� Electrolyte is poisonous anddangerous since it contains sul-furic acid, which causes severeburns. Avoid any contact withskin, eyes or clothing and al-ways shield your eyes whenworking near batteries. In caseof contact, administer the fol-lowing FIRST AID.• EXTERNAL: Flush with plenty

of water.• INTERNAL: Drink large quan-

tities of water or milk and im-mediately call a physician.

• EYES: Flush with water for 15minutes and seek promptmedical attention.

� Batteries produce explosive hy-drogen gas. Therefore, keepsparks, flames, cigarettes, etc.,away from the battery and pro-vide sufficient ventilation whencharging it in an enclosedspace.

� KEEP THIS AND ALL BATTER-IES OUT OF THE REACH OFCHILDREN.

To charge the batteryHave a Yamaha dealer charge the bat-tery as soon as possible if it seems tohave discharged. Keep in mind that thebattery tends to discharge more quicklyif the vehicle is equipped with optionalelectrical accessories.

To store the battery1. If the vehicle will not be used for

more than one month, remove thebattery, fully charge it, and thenplace it in a cool, dry place.

2. If the battery will be stored for morethan two months, check it at leastonce a month and fully charge it ifnecessary.

3. Fully charge the battery before in-stallation.

4. After installation, make sure thatthe battery leads are properly con-nected to the battery terminals.

1. Negative battery lead (black)2. Positive battery lead (red)3. Battery



6-30

6

CAUTION:ECA10630

� Always keep the batterycharged. Storing a dischargedbattery can cause permanentbattery damage.

� To charge a sealed-type (MF)battery, a special (constant-volt-age) battery charger is required.Using a conventional batterycharger will damage the battery.If you do not have access to asealed-type (MF) battery charg-er, have a Yamaha dealercharge your battery.

EAU42582

Replacing the fuses The main fuse, the fuel injection systemfuse, and the fuse box, which containsthe fuses for the individual circuits, arelocated under the rider seat. (See page3-11.)If a fuse is blown, replace it as follows.

1. Unhook the battery band, and thenremove the battery cover.

2. Turn the key to “OFF” and turn offthe electrical circuit in question.

3. Remove the blown fuse, and theninstall a new fuse of the specifiedamperage.

1. Battery band2. Battery cover

1. Main fuse2. Fuse box3. Fuel injection system fuse4. Fuel injection system spare fuse



6-31

6

CAUTION:ECA10640

Do not use a fuse of a higher amper-age rating than recommended toavoid causing extensive damage tothe electrical system and possibly afire.

4. Turn the key to “ON” and turn onthe electrical circuit in question tocheck if the device operates.

5. If the fuse immediately blowsagain, have a Yamaha dealercheck the electrical system.

6. Install the battery cover, and thenhook the battery band onto theholder.

1. Signaling system fuse2. Ignition fuse3. Taillight fuse4. Radiator fan fuse5. Backup fuse (for odometer and clock)6. Headlight fuse7. Spare fuse

Specified fuses:Main fuse:

50.0 AHeadlight fuse:

20.0 ASignaling system fuse:

10.0 ATaillight fuse:

10.0 AIgnition fuse:

15.0 AFuel injection system fuse:

10.0 ABackup fuse:

10.0 ARadiator fan fuse:

20.0 A



6-32

6

EAU42470

Replacing the headlight bulb This model is equipped with a quartzbulb headlight. If the headlight bulbburns out, replace it as follows.

1. Remove the turn signal/positionlight bracket cover by removing thebolts.

2. Remove the headlight unit by re-moving the bolts on each side.

3. Disconnect the headlight coupler,and then remove the bulb cover.

4. Unhook the headlight bulb holder,and then remove the defectivebulb.

WARNINGEWA10790

Headlight bulbs get very hot. There-fore, keep flammable products awayfrom a lit headlight bulb, and do nottouch the bulb until it has cooleddown.

5. Place a new headlight bulb into po-sition, and then secure it with thebulb holder.

CAUTION:ECA10660

Do not touch the glass part of theheadlight bulb to keep it free fromoil, otherwise the transparency ofthe glass, the luminosity of the bulb,

1. Turn signal/position light bracket cover2. Bolt

1. Bolt

1. Headlight bulb cover2. Headlight coupler

1. Headlight bulb holder2. Headlight bulb



6-33

6

and the bulb life will be adversely af-fected. Thoroughly clean off any dirtand fingerprints on the headlightbulb using a cloth moistened with al-cohol or thinner.

6. Install the headlight bulb cover,and then connect the coupler.

7. Install the headlight unit by install-ing the bolts.

8. Place the turn signal/position lightbracket cover in the original posi-tion, and then install the bolts.

9. Have a Yamaha dealer adjust theheadlight beam if necessary.

EAU24131

Replacing the tail/brake light bulb

1. Remove the tail/brake light lens byremoving the screws.

2. Remove the defective bulb bypushing it in and turning it counter-clockwise.

3. Insert a new bulb into the socket,push it in, and then turn it clock-wise until it stops.

4. Install the lens by installing thescrews.

CAUTION:ECA10680

Do not overtighten the screws, oth-erwise the lens may break.

1. Do not touch the glass part of the bulb.1. Screw



6-34

6

EAU42460

Replacing a front turn signal light bulb

1. Remove the front turn signal lightouter lens by removing the screws.

2. Remove the inner lens by pulling itout.



5. Place the inner lens in the originalposition, and then install the outerlens by installing the screws.

CAUTION:ECA10680


EAU42450

Replacing a rear turn signal light bulb

1. Remove the turn signal lens by re-moving the screws.



4. Install the lens by installing thescrews.

CAUTION:ECA10680


1. Screw

1. Inner lens

1. Screw



6-35

6

EAU42482

Replacing the license plate light bulb

1. Remove the license plate light cov-er by removing the bolts.

2. Pull the license plate light unit upas shown.

3. Remove the license plate lightsocket (together with the bulb) byturning it counterclockwise, andthen pulling it out.

4. Remove the defective bulb by pull-ing it out from the socket.

5. Insert a new bulb into the socket.

6. Install the socket (together with thebulb) by pushing it in and turning itclockwise until it stops.

7. Place the license plate light unit inthe original position, and then in-stall the license plate light cover byinstalling the bolts.

1. License plate light cover2. Bolt

1. License plate light unit

1. License plate light bulb socket

1. License plate light bulb



6-36

6

EAU24350

Supporting the motorcycle Since this model is not equipped with acenterstand, follow these precautionswhen removing the front and rearwheel or performing other maintenancerequiring the motorcycle to stand up-right. Check that the motorcycle is in astable and level position before startingany maintenance. A strong woodenbox can be placed under the engine foradded stability.

To service the front wheel1. Stabilize the rear of the motorcycle

by using a motorcycle stand or, ifan additional motorcycle stand isnot available, by placing a jack un-der the frame in front of the rearwheel.

2. Raise the front wheel off theground by using a motorcyclestand.

To service the rear wheelRaise the rear wheel off the ground byusing a motorcycle stand or, if a motor-cycle stand is not available, by placing

a jack either under each side of theframe in front of the rear wheel or undereach side of the swingarm.

EAU25870

Troubleshooting Although Yamaha motorcycles receivea thorough inspection before shipmentfrom the factory, trouble may occur dur-ing operation. Any problem in the fuel,compression, or ignition systems, forexample, can cause poor starting andloss of power.The following troubleshooting chartsrepresent quick and easy proceduresfor checking these vital systems your-self. However, should your motorcyclerequire any repair, take it to a Yamahadealer, whose skilled technicians havethe necessary tools, experience, andknow-how to service the motorcycleproperly.Use only genuine Yamaha replace-ment parts. Imitation parts may look likeYamaha parts, but they are often inferi-or, have a shorter service life and canlead to expensive repair bills.



6-37

6

EAU42500

Troubleshooting charts

Starting problems or poor engine performance

WARNINGEWA10840

Keep away open flames and do not smoke while checking or working on the fuel system.

Check the fuel level inthe fuel tank.

1. FuelThere is enough fuel.

There is no fuel.

Check the compression.

Supply fuel. The engine does not start. Check the compression.

Operate the electric starter.

2. CompressionThere is compression.

There is no compression.

Check the ignition.

Have a Yamaha dealercheck the vehicle.

Remove the spark plugsand check the electrodes.

3. Ignition Wipe off with a dry cloth and correct thespark plug gaps, or replace the spark plugs.

Have a Yamaha dealer check the vehicle.

The engine does not start.Have a Yamaha dealercheck the vehicle.

The engine does not start.Check the battery.

Operate the electric starter.

4. BatteryThe engine turns over quickly.

The engine turns over slowly.

The battery is good.

Check the battery lead connections,and charge the battery if necessary.

Dry

Wet Operate the electric starter.



6-38

6

Engine overheating

WARNINGEWAT1040

� Do not remove the radiator cap when the engine and radiator are hot. Scalding hot fluid and steam may beblown out under pressure, which could cause serious injury. Be sure to wait until the engine has cooled.

� Place a thick rag, like a towel, over the radiator cap, and then slowly rotate the cap counterclockwise to the de-tent to allow any residual pressure to escape. When the hissing sound has stopped, press down on the capwhile turning it counterclockwise, and then remove the cap.

NOTE:If coolant is not available, tap water can be temporarily used instead, provided that it is changed to the recommended coolantas soon as possible.

Wait until the engine has cooled.

Check the coolant level in the reservoir and radiator.

The coolant level is OK.

The coolant level is low.Check the cooling systemfor leakage.

Have a Yamaha dealer checkand repair the cooling system.

Add coolant. (See NOTE.)

Start the engine. If the engine overheats again, have a Yamaha dealer check and repair the cooling system.

There isleakage.

There is no leakage.


MOTORCYCLE CARE AND STORAGE

7-1

7

EAU37833

Matte color caution

CAUTION:ECA15192

Some models are equipped withmatte colored finished parts. Besure to consult a Yamaha dealer foradvice on what products to use be-fore cleaning the vehicle. Using abrush, harsh chemical products orcleaning compounds when cleaningthese parts will scratch or damagetheir surface. Wax also should notbe applied to any matte colored fin-ished parts.

EAU39164

Care While the open design of a motorcyclereveals the attractiveness of the tech-nology, it also makes it more vulnera-ble. Rust and corrosion can developeven if high-quality components areused. A rusty exhaust pipe may go un-noticed on a car, however, it detractsfrom the overall appearance of a motor-cycle. Frequent and proper care doesnot only comply with the terms of thewarranty, but it will also keep yourmotorcycle looking good, extend its lifeand optimize its performance.

Before cleaning1. Cover the muffler outlets with plas-

tic bags after the engine hascooled down.

2. Make sure that all caps and coversas well as all electrical couplersand connectors, including thespark plug caps, are tightly in-stalled.

3. Remove extremely stubborn dirt,like oil burnt onto the crankcase,with a degreasing agent and abrush, but never apply such prod-

ucts onto seals, gaskets, the drivebelt and wheel axles. Always rinsethe dirt and degreaser off with wa-ter.

Cleaning

CAUTION:ECA10771

� Avoid using strong acidic wheelcleaners, especially on spokedwheels. If such products areused on hard-to-remove dirt, donot leave the cleaner on the af-fected area any longer than in-structed. Also, thoroughly rinsethe area off with water, immedi-ately dry it, and then apply a cor-rosion protection spray.

� Improper cleaning can damageplastic parts such as cowlings,panels, windshields, headlightlenses, meter lenses, etc. Useonly a soft, clean cloth orsponge with mild detergent andwater to clean plastic.

� Do not use any harsh chemicalproducts on plastic parts. Besure to avoid using cloths orsponges which have been in



7-2

7

contact with strong or abrasivecleaning products, solvent orthinner, fuel (gasoline), rust re-movers or inhibitors, brake flu-id, antifreeze or electrolyte.

� Do not use high-pressure wash-ers or steam-jet cleaners sincethey cause water seepage anddeterioration in the following ar-eas: seals (of wheel and swing-arm bearings, fork and brakes),electric components (couplers,connectors, instruments,switches and lights), breatherhoses and vents.

� For motorcycles equipped witha windshield: Do not use strongcleaners or hard sponges asthey will cause dulling orscratching. Some cleaning com-pounds for plastic may leavescratches on the windshield.Test the product on a small hid-den part of the windshield tomake sure that it does not leaveany marks. If the windshield is

scratched, use a quality plasticpolishing compound afterwashing.

After normal useRemove dirt with warm water, a milddetergent, and a soft, clean sponge,and then rinse thoroughly with cleanwater. Use a toothbrush or bottlebrushfor hard-to-reach areas. Stubborn dirtand insects will come off more easily ifthe area is covered with a wet cloth fora few minutes before cleaning.

After riding in the rain, near the sea oron salt-sprayed roadsSince sea salt or salt sprayed on roadsduring winter are extremely corrosive incombination with water, carry out thefollowing steps after each ride in therain, near the sea or on salt-sprayedroads.

NOTE:Salt sprayed on roads in the winter mayremain well into spring.

1. Clean the motorcycle with cold wa-ter and a mild detergent, after theengine has cooled down.

CAUTION:ECA10790

Do not use warm water since it in-creases the corrosive action of thesalt.

2. After drying the motorcycle, applya corrosion protection spray on allmetal, including chrome- and nick-el-plated, surfaces to prevent cor-rosion.

After cleaning1. Dry the motorcycle with a chamois

or an absorbing cloth.2. Use a chrome polish to shine

chrome, aluminum and stainless-steel parts, including the exhaustsystem. (Even the thermally in-duced discoloring of stainless-steel exhaust systems can be re-moved through polishing.)



7-3

7

3. To prevent corrosion, it is recom-mended to apply a corrosion pro-tection spray on all metal,including chrome- and nickel-plat-ed, surfaces.

4. Use spray oil as a universal clean-er to remove any remaining dirt.

5. Touch up minor paint damagecaused by stones, etc.

6. Wax all painted and chrome-plat-ed surfaces. Avoid combinationcleaner waxes, many of whichcontain abrasives that may marthe paint or protective finish.

7. Let the motorcycle dry completelybefore storing or covering it.

WARNINGEWA11130

� Make sure that there is no oil orwax on the brakes or tires.

� If necessary, clean the brakediscs and brake linings with aregular brake disc cleaner or ac-etone, and wash the tires withwarm water and a mild deter-gent. Before riding at higher

speeds, test the motorcycle’sbraking performance and cor-nering behavior.

CAUTION:ECA10950

� Apply spray oil and wax spar-ingly and make sure to wipe offany excess.

� Never apply oil or wax to thedrive belt.

� Never apply oil or wax to anyrubber and plastic parts, buttreat them with a suitable careproduct.

� Avoid using abrasive polishingcompounds as they will wearaway the paint.

NOTE:Consult a Yamaha dealer for advice onwhat products to use.

Special care is needed for cleaningthe windshield and sidebags on thismodel. Be sure to follow the instruc-tions below.

Cleaning the windshieldAvoid using any alkaline or strong acidcleaner, gasoline, brake fluid, or anyother solvent. Clean the windshield witha cloth or sponge dampened with aneutral detergent, and after cleaning,thoroughly wash it off with water. Foradditional cleaning, use Yamaha Wind-shield Cleaner or other quality cleaner.Some cleaning compounds for plasticsmay leave scratches on surfaces of thewindshield. Before using them, make atest by polishing an area which doesnot affect your visibility.

Cleaning the sidebagsWater can be harmful to untreatedleather. Use Yamaha Saddle Soap oranother quality brand according to themanufacturer’s directions to clean theleather on the sidebags. Polish the dryleather with a soft cloth, and then treatwith Yamaha Mink Oil or another high-quality leather protectant for increasedwater resistance.



7-4

7

EAU26280

Storage

Short-termAlways store your motorcycle in a cool,dry place and, if necessary, protect itagainst dust with a porous cover.

CAUTION:ECA10810

� Storing the motorcycle in apoorly ventilated room or cover-ing it with a tarp, while it is stillwet, will allow water and humid-ity to seep in and cause rust.

� To prevent corrosion, avoiddamp cellars, stables (becauseof the presence of ammonia)and areas where strong chemi-cals are stored.

Long-termBefore storing your motorcycle for sev-eral months:

1. Follow all the instructions in the“Care” section of this chapter.

2. Fill up the fuel tank and add fuelstabilizer (if available) to preventthe fuel tank from rusting and thefuel from deteriorating.

3. Perform the following steps to pro-tect the cylinders, piston rings, etc.from corrosion.a. Remove the spark plug caps

and spark plugs.b. Pour a teaspoonful of engine oil

into each spark plug bore.c. Install the spark plug caps onto

the spark plugs, and then placethe spark plugs on the cylinderhead so that the electrodes aregrounded. (This will limit spark-ing during the next step.)

d. Turn the engine over severaltimes with the starter. (This willcoat the cylinder walls with oil.)

e. Remove the spark plug capsfrom the spark plugs, and theninstall the spark plugs and thespark plug caps.

WARNINGEWA10950

To prevent damage or injury fromsparking, make sure to ground thespark plug electrodes while turningthe engine over.

4. Lubricate all control cables and thepivoting points of all levers andpedals as well as of the side-stand/centerstand.

5. Check and, if necessary, correctthe tire air pressure, and then liftthe motorcycle so that both of itswheels are off the ground. Alterna-tively, turn the wheels a little everymonth in order to prevent the tiresfrom becoming degraded in onespot.

6. Cover the muffler outlet with aplastic bag to prevent moisturefrom entering it.

7. Remove the battery and fullycharge it. Store it in a cool, dryplace and charge it once a month.Do not store the battery in an ex-cessively cold or warm place [lessthan 0 °C (30°F) or more than 30°C (90°F)]. For more informationon storing the battery, see page6-29.

NOTE:Make any necessary repairs beforestoring the motorcycle.


SPECIFICATIONS

8-1

8

Dimensions:Overall length:

2490 mm (98.0 in)Overall width:

980 mm (38.6 in)Overall height:

1520 mm (59.8 in)Seat height:

715 mm (28.1 in)Wheelbase:

1690 mm (66.5 in)Ground clearance:

145 mm (5.71 in)Minimum turning radius:

3500 mm (137.8 in)Weight:

With oil and fuel:323.0 kg (712 lb)

Engine:Engine type:

Liquid cooled 4-stroke, SOHCCylinder arrangement:

V-type 2-cylinderDisplacement:

1304.0 cm³Bore × stroke:

100.0 × 83.0 mm (3.94 × 3.27 in)Compression ratio:

9.50 :1Starting system:

Electric starterLubrication system:

Wet sump

Engine oil:Type:

YAMALUBE 4 (20W40) or SAE20W40Recommended engine oil grade:

API service SG type or higher, JASO standard MA

Engine oil quantity:Without oil filter cartridge replacement:

3.20 L (3.38 US qt) (2.82 Imp.qt)With oil filter cartridge replacement:

3.40 L (3.59 US qt) (2.99 Imp.qt)Cooling system:

Coolant reservoir capacity (up to the maximum level mark):

0.45 L (0.48 US qt) (0.40 Imp.qt)Radiator capacity (including all routes):

2.10 L (2.22 US qt) (1.85 Imp.qt)Air filter:

Air filter element:Oil-coated paper element

Fuel:Recommended fuel:

Unleaded gasoline onlyFuel tank capacity:

18.5 L (4.89 US gal) (4.07 Imp.gal)Fuel reserve amount:

3.7 L (0.98 US gal) (0.81 Imp.gal)Fuel injection:

Throttle body:Manufacturer:

MIKUNIType/quantity:

ACW40/2

Spark plug (s):Manufacturer/model:

NGK/LMAR7A-9Spark plug gap:

0.8–0.9 mm (0.031–0.035 in)Clutch:

Clutch type:Wet, multiple-disc

Transmission:Primary reduction system:

Spur gearPrimary reduction ratio:

70/45 (1.556)Secondary reduction system:

Belt driveSecondary reduction ratio:

70/30 (2.333)Transmission type:

Constant mesh 5-speedOperation:

Left foot operationGear ratio:

1st:36/13 (2.769)

2nd:32/18 (1.778)

3rd:29/21 (1.381)

4th:29/26 (1.115)

5th:24/25 (0.960)


SPECIFICATIONS

8-2

8

Chassis:Frame type:

Double cradleCaster angle:

32.70 °Trail:

145.0 mm (5.71 in)Front tire:

Type:Tubeless

Size:130/90 16M/C 67H

Manufacturer/model:DUNLOP/D404F X

Manufacturer/model:BRIDGESTONE/EXEDRA G721

Rear tire:Type:

TubelessSize:

170/70B 16M/C 75HManufacturer/model:

DUNLOP/K555Manufacturer/model:

BRIDGESTONE/EXEDRA G722 GLoading:

Maximum load:190 kg (419 lb)(Total weight of rider, passenger, cargo and accessories)

Tire air pressure (measured on cold tires):

Loading condition:0–90 kg (0–198 lb)

Front:250 kPa (36 psi) (2.50 kgf/cm²)

Rear:280 kPa (41 psi) (2.80 kgf/cm²)

Loading condition:90–190 kg (198–419 lb)Front:

250 kPa (36 psi) (2.50 kgf/cm²)Rear:

280 kPa (41 psi) (2.80 kgf/cm²)Front wheel:

Wheel type:Cast wheel

Rim size:16M/C x MT3.00

Rear wheel:Wheel type:

Cast wheelRim size:

16M/C x MT4.50Front brake:

Type:Dual disc brake

Operation:Right hand operation

Recommended fluid:DOT 4

Rear brake:Type:

Single disc brakeOperation:

Right foot operationRecommended fluid:

DOT 4

Front suspension:Type:

Telescopic forkSpring/shock absorber type:

Coil spring/oil damperWheel travel:

135.0 mm (5.31 in)Rear suspension:

Type:Swingarm (link suspension)

Spring/shock absorber type:Coil spring/gas-oil damper

Wheel travel:110.0 mm (4.33 in)

Electrical system:Ignition system:

Transistorized coil ignition (digital)Charging system:

AC magnetoBattery:

Model:YTX20L-BS

Voltage, capacity:12 V, 18.0 Ah

Headlight:Bulb type:

Halogen bulbBulb voltage, wattage × quantity:

Headlight:12 V, 60 W/55.0 W × 1

Tail/brake light:12 V, 5.0 W/21.0 W × 1

Front turn signal/position light:12 V, 21 W/5.0 W × 2


SPECIFICATIONS

8-3

8

Rear turn signal light:12 V, 21.0 W × 2

License plate light:12 V, 5.0 W × 1

Meter lighting:LED

Neutral indicator light:LED

High beam indicator light:LED

Oil level warning light:LED

Turn signal indicator light:LED

Fuel level warning light:LED

Coolant temperature warning light:LED

Engine trouble warning light:LED

Fuses:Main fuse:

50.0 AHeadlight fuse:

20.0 ATaillight fuse:

10.0 ASignaling system fuse:

10.0 AIgnition fuse:

15.0 ARadiator fan fuse:

20.0 A

Fuel injection system fuse:10.0 A

Backup fuse:10.0 A


CONSUMER INFORMATION

9-1

9

EAU26351

Identification numbers Record the key identification number,vehicle identification number and mod-el label information in the spaces pro-vided below for assistance whenordering spare parts from a Yamahadealer or for reference in case the vehi-cle is stolen.KEY IDENTIFICATION NUMBER:

VEHICLE IDENTIFICATION NUMBER:

MODEL LABEL INFORMATION:

EAU26381

Key identification number

The key identification number isstamped into the key tag. Record thisnumber in the space provided and useit for reference when ordering a newkey.

EAU26400

Vehicle identification number

The vehicle identification number isstamped into the steering head pipe.Record this number in the space pro-vided.

NOTE:The vehicle identification number isused to identify your motorcycle andmay be used to register your motor-cycle with the licensing authority in yourarea.

1. Key identification number 1. Vehicle identification number



9-2

9

EAU26470

Model label

The model label is affixed to the frameunder the rider seat. (See page 3-11.)Record the information on this label inthe space provided. This informationwill be needed when ordering spareparts from a Yamaha dealer.

1. Model label



9-3

9

EAU26551

Reporting safety defects If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediatelyinform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Yamaha Motor Corporation,U.S.A. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a groupof vehicles, it may order a recall and remedy campaign. However, NHTSA cannot become involved in individual problemsbetween you, your dealer, or Yamaha Motor Corporation, U.S.A.To contact NHTSA, you may call the Vehicle Safety Hotline toll-free at 1-888-327-4236 (TTY: 1-800-424-9153); go tohttp://www.safercar.gov; or write to: Administrator, NHTSA, 400 Seventh Street, SW., Washington, DC 20590. You can alsoobtain other information about motor vehicle safety from http://www.safercar.gov.



9-4

9

EAU26560

Motorcycle noise regulation TAMPERING WITH NOISE CONTROL SYSTEM PROHIBITED:Federal law prohibits the following acts or the causing thereof: (1) The removal or rendering inoperative by any person otherthan for purposes of maintenance, repair, or replacement of any device or element of design incorporated into any new ve-hicle for the purpose of noise control prior to its sale or delivery to the ultimate purchaser or while it is in use or (2) the use ofthe vehicle after such device or element of design has been removed or rendered inoperative by any person.“AMONG THOSE ACTS PRESUMED TO CONSTITUTE TAMPERING ARE THE ACTS LISTED BELOW”.These acts include tampering with the following systems; i.e., modification, removal, etc.

Exhaust system• Muffler• Exhaust pipe• Silencer

Intake system• Air cleaner case• Air cleaner element• Intake duct



9-5

9

EAU26632

Maintenance record Copies of work orders and/or receipts for parts purchased and installed on your vehicle will be required to document thatmaintenance has been completed in accordance with the emissions warranty. The chart below is printed only as a reminderthat maintenance work is required. It is not acceptable proof of maintenance work.

Maintenanceinterval

Date ofservice Mileage Servicing dealer

name and address Remarks

600 mi(1000 km) or

1 month4000 mi

(7000 km) or6 months8000 mi







(49000 km) or48 months



9-6

9

36000 mi(55000 km) or

54 months40000 mi

(61000 km) or60 months

Maintenanceinterval

Date ofservice Mileage Servicing dealer

name and address Remarks



9-7

9

EAU26663

YAMAHA MOTOR CORPORATION, U.S.A. STREET AND ENDURO MOTORCYCLE LIMITED WARRANTY

a)b)

c)d)e)f)

1.

2.

Yamaha Motor Corporation, U.S.A. hereby warrants that new Yamaha motorcycles will be free from defects in material and workmanship for the period of time stated herein, subject to certain stated limitations.

THE PERIOD OF WARRANTY for Yamaha motorcycles originally equipped with headlight, stoplight, and turn signals shall be one (1) year from the date of purchase, with no mileage limitation.

MODELS EXCLUDED FROM WARRANTY include those used for non-Yamaha-authorized renting, leasing or other commercial purposes, and TZ models.

DURING THE PERIOD OF WARRANTY, any authorized Yamaha motorcycle dealer will, free of charge, repair or replace any part adjudged defective by Yamaha due to faulty workmanship or material from the factory. Parts used in warranty repairs will be warranted for the balance of the product’s warranty period. All parts replaced under warranty become property of Yamaha Motor Corporation, U.S.A.

GENERAL EXCLUSIONS from this warranty shall include any failures caused by:

Competition or racing use.Installation of parts or accessories that are not qualitatively equivalent to genuine Yamaha parts.Abnormal strain, neglect, or abuse.Lack of proper maintenance.Accident or collision damage.Modification to original parts.

SPECIFIC EXCLUSIONS from this warranty shall include parts replaced due to normal wear or routine maintenance.

THE CUSTOMER’S RESPONSIBILITY under this warranty shall be to:

Operate and maintain the motorcycle as specified in the appropriate Owner’s Manual, andGive notice to an authorized Yamaha motorcycle dealer of any and all apparent defects within ten (10) days after discovery, and make the machine available at that time for inspection and repairs at such dealer’s place of business.

WARRANTY TRANSFER: To transfer the warranty from the original purchaser to any subsequent purchaser, it is imperative that the machine be inspected and registered for warranty by an authorized Yamaha motorcycle dealer. In order for this warranty to remain in effect, this inspection and registration must take place within ten (10) days after transfer. An inspection and registration fee will be charged for this service.

EMISSION CONTROL SYSTEM WARRANTY:Yamaha Motor Corporation, U.S.A. also warrants to the ultimate purchaser and each subsequent purchaser of each Yamaha motorcycle covered by this warranty with a displacement of 50cc or greater, that the vehicle is designed, built, and equipped so as to conform at the time of sale with all U.S. emissions standards applicable at the time of manufacture and that it is free from defects in materials and workmanship which would cause it not to meet these standards within the period listed immediately below. Failures other than those resulting from defects in material or workmanship, which arise solely as a result of owner abuse and/or lack of proper maintenance, are not covered by this warranty.

Period6,000 km (3,750 miles)

or five years, whichever occurs first

12,000 km (7,465 miles)or five years whichever occurs first

18,000 km (11,185 miles)or five years, whichever occurs first

30,000 km (18,641 miles)or five years, whichever occurs first

YAMAHA MOTOR CORPORATION, U.S.A. MAKES NO OTHER WARRANTY OF ANY KIND, EXPRESSED OR IMPLIED. ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE WHICH EXCEED THE OBLIGATIONS AND TIME LIMITS STATED IN THIS WARRANTY ARE HEREBY DISCLAIMED BY YAMAHA MOTOR CORPORATION, U.S.A. AND EXCLUDED FROM THIS WARRANTY.

SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU. ALSO EXCLUDED FROM THIS WARRANTY ARE ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES INCLUDING LOSS OF USE. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE EXCLUSION MAY NOT APPLY TO YOU.

THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.

YAMAHA MOTOR CORPORATION, U.S.A.P.O. Box 6555

Cypress, California 90630

Engine Displacement Under 50cc

50cc to 169cc

170cc to 279cc

280cc and over



9-8

9

WARRANTY QUESTIONS AND ANSWERS

What costs are my responsibility during the warranty period?The customer’s responsibility includes all costs of normal maintenance services, non-warranty repairs, accident and collision damages, and oil, oil filters, air filters, spark plugs, and brake shoes.

What are some examples of “abnormal” strain, neglect, or abuse?These terms are general and overlap each other in areas. Specific examples include: Running the machine out of oil, sustained high rpm, full-throttle, operating the machine with a broken or damaged part which causes another part to fail, damage or failure due to improper or careless transportation and/or tie-down. If you have any specific questions on operation or maintenance, please contact your dealer for advice.

Does the warranty cover incidental costs such as towing or transportation due toa failure?No. The warranty is limited to repair of the machine itself.

May I perform any or all of the recommended maintenance shown in the Owner’s Manual instead of having the dealer do them?Yes, if you are a qualified mechanic and follow the procedures specified in the Owner’s and Service Manual. We do recommend, however, that items requiring special tools or equipment be done by a Yamaha motorcycle dealer.

Will the warranty be void or cancelled if I do not operate or maintain my new motorcycle exactly as specified in the Owner’s Manual?No. The warranty on a new motorcycle cannot be “voided” or “cancelled.” However, if a particular failure is caused by operation or maintenance other than as described in the Owner’s Manual, that failure may not be covered under warranty.

What responsibility does my dealer have under this warranty?Each Yamaha motorcycle dealer is expected to:

Completely set up every new machine before sale.Explain the operation, maintenance, and warranty requirements to your satisfaction at the time of sale, and upon your request at any later date.Each Yamaha motorcycle dealer is held responsible for his setup, service and warranty repair work.

Is the warranty transferable to second owners?Yes. The remainder of the existing warranty can be transferred upon request. The unit has to be inspected and re-registered by an authorized Yamaha motorcycle dealer for the policy to remain effective.

CUSTOMER SERVICE

If your machine requires warranty service, you must take it to any authorized Yamaha motorcycle dealer within the continental United States. Be sure to bring your warranty registration card or other valid proof of the original date of purchase. If a question or problem arises regarding the warranty, first contact the owner of the dealership. Since all warranty matters are handled at the dealer level, this person is in the best position to help you. IF you are still not satisfied and require additional assistance, please write to:

YAMAHA MOTOR CORPORATION, U.S.A.CUSTOMER RELATIONS DEPARTMENT

P.O. Box 6555Cypress, California 90630

When contacting Yamaha Motor Corporation, U.S.A., don’t forget to include any important information such as names, addresses, model, V.I.N. (frame number), dates, and receipts.

CHANGE OF ADDRESS

The federal government requires each manufacturer of a motor vehicle to maintain a complete, up-to-date list of all first purchasers against the possibility of a safety-related defect and recall. This list is compiled from the purchase registrations sent to Yamaha Motor Corporation, U.S.A. by the selling dealer at the time of your purchase.

If you should move after you have purchased your new motorcycle, please advise us of your new address by sending a postcard listing your motorcycle model name, V.I.N. (frame number), dealer number (or dealer’s name) as it is shown on your warranty card, your name and new mailing address. Mail to:

YAMAHA MOTOR CORPORATION, U.S.A.P.O. Box 6555

Cypress, California 90630Attention: Warranty Department

This will ensure that Yamaha Motor Corporation, U.S.A. has an up-to-date registration record in accordance with federal law.

Q.A.

Q.A.

Q.

A.

Q.

A.

Q.

A.

Q.A.

1.2.

3.

Q.A.



9-9

9

EAU26750

YAMAHA EXTENDED SERVICE (Y.E.S.) Keep your Yamaha protected even after your warranty expires with genuine Yamaha Extended Service (Y.E.S.).

Y.E.S. is designed and administered by Yamaha Motor Corporation to provide maximum owner satisfaction. You get uninterrupted factory-backed coverage for extra peace of mind.

Y.E.S. is flexible. You choose the plan that’s right foryou: 12 months, 24 months, 36 months or, on certain models, even 48 months beyond your warranty period.

Y.E.S. is designed and administered by the same Yamaha people who handle your warranty – and itshows in the comprehensive coverage benefits. There are no mileage limitations. Coverage isn’t limited to “moving parts” or the “drive train” like many other plans. And Y.E.S. covers manufacturing defects just like the warranty. See the sample contract at your Yamahadealer to see how comforting uninterrupted factory-backed protection can be.

You don’t have to pay anything for covered repairs. There’s no deductible to pay, and repairs aren’t“pro-rated.” You don’t have any “out-of-pocket” expenses for covered repairs.

In addition, Travel and Recreation Interruption Protection (TRIP) is included at no extra cost. TRIP gives you up to $150 reimbursement per occurrence for any reasonable expenses you incur because your Yamaha needs covered service: replacement vehicle rental, emergency towing, phone calls, even food and lodging when you are away from home. This superb coverage goes into effect when you purchase Y.E.S., so it applies to any warranty repairs as well as covered repairs during your entire Y.E.S. plan period.

Y.E.S. coverage is honored at any authorized Yamaha dealer nationwide.

Y.E.S. coverage is transferable to a new owner if yousell or trade-in. That can make your Yamaha much more valuable!

This excellent Y.E.S. plan coverage is only available to Yamaha owners like you, and only while your Yamaha is still within the Yamaha Limited Warranty period. So visit your authorized Yamaha dealer to get all the facts. He can show you how easy it is to protect your investment with Yamaha Extended Service.



9-10

9

We urge you to act now. You’ll get the excellent benefits of TRIP coverage right away, and you’ll rest easy knowing you’ll have strong factory-backed protection even after your Yamaha Limited Warranty expires.

A special note:If visiting your dealer isn’t convenient, contact Yamaha with your Primary ID number (your frame number). We’ll be happy to help you get the Y.E.S. coverage you need.

Yamaha Service MarketingP.O. Box 6555Cypress, CA 906301-(866)-YES-EXTD (1-866-937-3983)


INDEXA

Accessories and replacement parts ..... 6-19Air filter element, replacing ................... 6-15

BBattery .................................................. 6-29Brake and clutch levers, checking and

lubricating ........................................... 6-25Brake and shift pedals, checking and

lubricating ........................................... 6-25Brake fluid, changing ............................ 6-23Brake fluid level, checking .................... 6-22Brake lever ............................................. 3-8Brake lever free play, adjusting ............ 6-20Brake pedal ............................................ 3-9

CCables, checking and lubricating.......... 6-24Canister (for California only)................. 6-11Care........................................................ 7-1Catalytic converter................................ 3-11Clutch lever............................................. 3-8Clutch lever free play, adjusting ........... 6-20Coolant ................................................. 6-14Coolant temperature warning light.......... 3-3

DDimmer switch ........................................ 3-7Drive belt slack ..................................... 6-23

EEngine break-in ...................................... 5-3Engine oil and oil filter cartridge ........... 6-11Engine stop switch.................................. 3-7Engine trouble warning light ................... 3-3

FFront and rear brake pads, checking.... 6-21Front fork, checking .............................. 6-27

Fuel .......................................................3-10Fuel level warning light............................3-2Fuel tank cap...........................................3-9Fuses, replacing....................................6-30

HHandlebar switches.................................3-6Headlight bulb, replacing.......................6-32Helmet holder........................................3-12High beam indicator light.........................3-2Horn switch .............................................3-7

IIdentification numbers .............................9-1Ignition circuit cut-off system.................3-15Indicator and warning lights ....................3-2

KKey identification number........................9-1

LLabels, location of ...................................1-5License plate light bulb, replacing .........6-35

MMain switch/steering lock ........................3-1Maintenance and lubrication, periodic.....6-4Maintenance, emission control system ...6-3Maintenance, periodic .............................6-1Maintenance record ................................9-5Matte color, caution.................................7-1Model label..............................................9-2Multi-function meter unit..........................3-3

NNeutral indicator light ..............................3-2Noise regulation ......................................9-4

OOil level warning light ..............................3-2

PPanel, removing and installing................ 6-9Parking.................................................... 5-4Part locations .......................................... 2-1Pre-operation check list .......................... 4-2

RRear brake light switch, adjusting ......... 6-21Rear suspension, lubricating ................ 6-27RESET switch......................................... 3-7Rider seat ............................................. 3-11

SSafety defects, reporting......................... 9-3Safety information................................... 1-1SELECT switch....................................... 3-7Shifting.................................................... 5-2Shift pedal............................................... 3-8Shock absorber assembly, adjusting .... 3-13Sidebags............................................... 3-12Sidestand.............................................. 3-14Sidestand, checking and lubricating ..... 6-26Spark plugs, checking............................. 6-9Specifications.......................................... 8-1Starting the engine.................................. 5-1Start switch ............................................. 3-7Steering, checking ................................ 6-28Storage ................................................... 7-4Supporting the motorcycle .................... 6-36Swingarm pivots, lubricating ................. 6-26

TTail/brake light bulb, replacing .............. 6-33Throttle cable free play, checking ......... 6-16Throttle grip and cable, checking and

lubricating ........................................... 6-24Tires...................................................... 6-17


INDEXTool kit .................................................... 6-1Troubleshooting .................................... 6-36Troubleshooting charts ......................... 6-37Turn signal indicator light ........................ 3-2Turn signal light bulb (front),

replacing ............................................. 6-34Turn signal light bulb (rear),

replacing ............................................. 6-34Turn signal switch ................................... 3-7

VValve clearance .................................... 6-16Vehicle identification number .................. 9-1

WWarranty, extended................................. 9-9Warranty, limited ..................................... 9-7Wheel bearings, checking..................... 6-28Wheels .................................................. 6-19



PRINTED IN JAPAN2007.05-1.4×1 CR

(E)

PRINTED ON RECYCLED PAPER YAMAHA MOTOR CO., LTD.

Documents

VSTAR 1300 XVS13CTX(C) OWNER'S MANUAL… · INTRODUCTION EAU10080 Congratulations on your purchase of the Yamaha XVS13CTX(C). This model is the result of Yamaha’s vast experience