Upload
others
View
6
Download
0
Embed Size (px)
Citation preview
Rear lid
Page 1 of 1Rear lid
22/11/2009vw-wi://rl/N.en-GB.K03589810.wi::35009344.xml?xsl=3
ToolsSpecial tools and workshop equipment required
Torque wrench -V.A.G 1783-
Torque wrench -V.A.G 1331-
Socket -T10010-
Page 1 of 2Tools
22/11/2009vw-wi://rl/N.en-GB.K03589810.wi::35009345.xml?xsl=3
Page 2 of 2Tools
22/11/2009vw-wi://rl/N.en-GB.K03589810.wi::35009345.xml?xsl=3
Assembly overview - rear lid1 - Rear lid
Removing and installing → Chapter
Adjusting → Chapter
2 - Lid lock Removing
and installing → Chapter
3 - Handle trim Removing
and installing → Chapter
4 - Damper Adjusting
→ Chapter
5 - Gas-filled strut Removing
→ Chapter Releasing
gas → Chapter
6 - Striker pin Adjusting
rigid striker pin → Chapter.
Adjust striker pin using power latching system → Chapter
7 - Guide pin Adjusting → Chapter
8 - Hinge Removing and installing → Chapter
Page 1 of 1Assembly overview - rear lid
22/11/2009vw-wi://rl/N.en-GB.K03589810.wi::35009346.xml?xsl=3
Removing and installing rear lid
Page 1 of 1Removing and installing rear lid
22/11/2009vw-wi://rl/N.en-GB.K03589810.wi::35009347.xml?xsl=3
Removing
– Open rear lid -1-.
– Remove rear lid trim → General body repairs, interior; Rep. Gr.70.
– Disconnect connectors from existing electrical components and washer system hose (if fitted) → Electrical system; Rep. Gr.92
– Disconnect connector for high-level brake light → Electrical system; Rep. Gr.94
– Disconnect connector from rear lid lock. Remove rear lid lock → Chapter
– Guide hoses and wiring out through opening.
– Loosen bolts -2- at hinges -3- on left and right (do not remove).
– Further dismantling is possible only with the help of a second mechanic.
– Detach gas-filled struts -4- on left and right of rear lid -1- → Chapter.
– Only now unscrew bolts -2- and remove rear lid -1- from body.
Page 1 of 1Removing
22/11/2009vw-wi://rl/N.en-GB.K03589810.wi::35009348.xml?xsl=3
Installing
Rear lid -1- installation is performed in the reverse order of removal.
– Tighten bolts -2- to 20 Nm.
Note
Carry out corrosion protection measures on lid hinge and securing bolts after assembly work.
Page 1 of 1Installing
22/11/2009vw-wi://rl/N.en-GB.K03589810.wi::35009349.xml?xsl=3
Removing gas-filled strut– Open rear lid
and support it.
– Position a small screwdriver beneath spring clip -2-.
– Raise spring clip -2- until spring clip can be moved over ball socket in -direction of arrow-.
– Pull gas-filled struts -1- from ball-head pins -3- and -4-.
After removing gas-filled strut -1-, slide spring clip -2- back immediately.
WARNINGProceed with care if gas-filled strut is reused. Spring clip must not be levered completely out of ball socket, as it will otherwise be damaged. Gas-filled strut springs out of mounting and causes damage or injury to operator.
– Specified torque for ball-head pins -3- and -4-20 Nm.
– Releasing gas from gas-filled strut -1-→ Chapter.
Page 1 of 1Removing gas-filled strut
22/11/2009vw-wi://rl/N.en-GB.K03589810.wi::35009350.xml?xsl=3
Removing and installing handle trim
Page 1 of 1Removing and installing handle trim
22/11/2009vw-wi://rl/N.en-GB.K03589810.wi::35009351.xml?xsl=3
Removing– Remove rear lid trim → General body
repairs, interior; Rep. Gr.70.
– Disconnect connector -2- for number plate lights from handle trim -1-.
– Remove the hexagon nuts -3- (Qty. 4) and remove handle trim -1- from the outside.
Page 1 of 1Removing
22/11/2009vw-wi://rl/N.en-GB.K03589810.wi::35009352.xml?xsl=3
InstallingHandle trim -1- installation is carried out in reverse order of removal.
– Tighten hexagon nuts -3- to 4.5 Nm.
Page 1 of 1Installing
22/11/2009vw-wi://rl/N.en-GB.K03589810.wi::35009353.xml?xsl=3
Removing and installing rear lid hinges
Note
Removal and installation is described for the right hinge only. Apply the same instructions for the left-hand side as appropriate.
Page 1 of 1Removing and installing rear lid hinges
22/11/2009vw-wi://rl/N.en-GB.K03589810.wi::35009354.xml?xsl=3
Removing
– Remove rear lid -1- → Chapter
– Remove rear roof trim → General body repairs, interior; Rep. Gr.70
– Remove the hexagon nuts -2- (Qty. 2) and remove base plate -1- from studs.
Note
Hexagon nuts -2- can only be loosened with a “long-shaft socket”, as rear lid hinge guide bolts are too long.
– Remove rear lid hinge from outside.
Page 1 of 1Removing
22/11/2009vw-wi://rl/N.en-GB.K03589810.wi::35009355.xml?xsl=3
Installing
Note
Before installing rear lid hinge -2- check seal -3- for damage and renew if necessary. Hexagon nuts -5- can only be loosened with a “long-shaft socket”, as rear lid hinge guide bolts are too
long.
– Position rear lid hinge -2- from outside.
– Slide base plate -4- onto studs on inner roof member and fit hexagon nuts -5-.
– Tighten hexagon nuts -5- to specified torque of 20 Nm.
– Adjust rear lid -1- → Chapter.
Note
Carry out corrosion protection measures on lid hinge and securing bolts after assembly and adjustment work.
Page 1 of 1Installing
22/11/2009vw-wi://rl/N.en-GB.K03589810.wi::35009356.xml?xsl=3
Adjusting rear lidThe rear lid can be adjusted only via the striker pin on lock cross member. The rear lid lock is bolted to the rear lid, it does not have elongated holes and therefore cannot be adjusted.
The buffers and guide wedges cannot be used to adjust the rear lid. They have the function of stabilising and damping the rear lid.
In conclusion, the rear lid adjustment is described in several steps. This includes the basic adjustment of the rear lid, the striker pins, guide pins and the dampers.
Page 1 of 1Adjusting rear lid
22/11/2009vw-wi://rl/N.en-GB.K03589810.wi::35009357.xml?xsl=3
Adjusting rear lidThe rear lid can be adjusted only via the striker pin on lock cross member. The rear lid lock is bolted to the rear lid, it does not have elongated holes and therefore cannot be adjusted.
The buffers and guide wedges cannot be used to adjust the rear lid. They have the function of stabilising and damping the rear lid.
In conclusion, the rear lid adjustment is described in several steps. This includes the basic adjustment of the rear lid, the striker pins, guide pins and the dampers.
Page 1 of 1Adjusting rear lid
22/11/2009vw-wi://rl/N.en-GB.K03589810.wi::35009357.xml?xsl=3
Basic adjustment of rear lid
Note
Vehicle must be standing on its wheels when adjustments are performed.
The rear lid is adjusted correctly if the shut lines/gaps are uniform all around, the lid is not too deep or too high and all contours align when lid is closed → Rep. Gr.00.
– Remove rear roof trim → General body repairs, interior; Rep. Gr.70.
– Remove gas-filled strut for rear lid → Chapter.
– Remove bumper cover end piece → Chapter.
– Loosen bolts -3- and -4- until guide pins -1-move freely on left and right sides. The striker wedges -2- must move in the guide pins without resistance.
– Loosen hexagon nuts -1- in rear roof member cut-out -2- (do not remove).
Note
Hexagon nuts -1- can only be loosened with a “long-shaft socket”, as rear lid hinge guide bolts are too long.
– Align rear lid uniformly according to outer contours -arrows- on left and right, the assistance of a second mechanic is required.
Page 1 of 2Basic adjustment of rear lid
22/11/2009vw-wi://rl/N.en-GB.K03589810.wi::35009358.xml?xsl=3
– Tighten hexagon nuts -1- to 20 Nm.
– Adjusting guide pins → Chapter.
Page 2 of 2Basic adjustment of rear lid
22/11/2009vw-wi://rl/N.en-GB.K03589810.wi::35009358.xml?xsl=3
Adjusting striker pin
Note
Vehicle must be standing on its wheels when adjustments are performed.
The rear lid is adjusted correctly if the shut lines/gaps are uniform all around, the lid is not too deep or too high and all contours align when lid is closed → Rep. Gr.00.
– The rear floor edge cover must be removed to adjust the rear striker pin → General body repairs, interior; Rep. Gr.70.
– The guide pins must be loose → Chapter.
– Loosen bolts -2- (do not remove) and striker pin -1- can be moved within over-size holes.
– Move striker pin -1- to rearmost position -arrow- and tighten bolts -2-
– Close rear lid and check adjustment.
– Following adjustment, retighten bolts -2- to specified torque of 20 Nm.
– Now the guide pins can be adjusted → Chapter.
Page 1 of 1Adjusting striker pin
22/11/2009vw-wi://rl/N.en-GB.K03589810.wi::35009359.xml?xsl=3
Adjusting striker pin for power latching system
Note
Vehicle must be standing on its wheels when adjustments are performed.
The rear lid is adjusted correctly if the shut lines/gaps are uniform all around, the lid is not too deep or too high and all contours align when lid is closed → Rep. Gr.00.
The battery must be fully charged and connected on vehicles with power latching system.
– The rear floor edge cover must be removed to adjust the rear striker pin on vehicles with power latching system → General body repairs, interior; Rep. Gr.70.
– The guide pins must be loose → Chapter.
– Loosen bolts -2- (do not remove) and striker pin (on vehicles with power latching system) -1- can be moved within over-size holes.
– Move striker pin -1- (on vehicles with power latching system) to rearmost position -arrow- and tighten bolts -2- (not fully).
– Close rear lid and check adjustment.
– Following adjustment, retighten bolts -2- to specified torque of 20 Nm.
– Now the guide pins can be adjusted → Chapter.
Page 1 of 1Adjusting striker pin for power latching system
22/11/2009vw-wi://rl/N.en-GB.K03589810.wi::35009360.xml?xsl=3
Adjusting guide wedge and guide pin
Page 1 of 1Adjusting guide wedge and guide pin
22/11/2009vw-wi://rl/N.en-GB.K03589810.wi::35009361.xml?xsl=3
Assembly overview1 - Bolt
Qty. 2 Specified
torque 8 Nm
2 - Guide pin Left and right
3 - Bolt Qty. 2 Specified
torque 8 Nm
4 - Guide wedge Left and right
Page 1 of 1Assembly overview
22/11/2009vw-wi://rl/N.en-GB.K03589810.wi::35009362.xml?xsl=3
Adjusting guide pins– Remove bumper cover end pieces → Chapter.
– The striker pin must be correctly positioned before adjusting guide pins.
– Adjust striker pin → Chapter
– Loosen bolts -3- and -4- (do not remove) until guide pins -1- move freely on left and right sides. The striker wedges -2- must move in the guide pins without resistance.
– Close rear lid.
– Press the guide wedge -2- against the guide pin -1- with slight force and tighten the bolts.
– Open rear lid and tighten bolt -3- to 15 Nm and bolt -4- to 8 Nm.
Page 1 of 1Adjusting guide pins
22/11/2009vw-wi://rl/N.en-GB.K03589810.wi::35009363.xml?xsl=3
Adjusting stop buffers
Note
Vehicle must be standing on its wheels when adjustments are performed.
The rear lid is adjusted correctly if the shut lines/gaps are uniform all around, the lid is not too deep or too high and all contours align when lid is closed → Rep. Gr.00.
– Loosen clamping bolt -2- until it is visible in rubber buffer.
– Pull detent slide -1- out from housing.
– Adjust detent slide to dimension -a = 12.5 mm-.
– Close rear lid with light pressure at centre of lid. Keep pulling on handle whilst doing this.
– Open rear lid again.
– Screw in clamping screw -1- to dimension -
Page 1 of 2Adjusting stop buffers
22/11/2009vw-wi://rl/N.en-GB.K03589810.wi::35009364.xml?xsl=3
a = 25 mm-.
Check setting.
Page 2 of 2Adjusting stop buffers
22/11/2009vw-wi://rl/N.en-GB.K03589810.wi::35009364.xml?xsl=3
Assembly overview - rear lid latch and release components
Page 1 of 1Assembly overview - rear lid latch and release components
22/11/2009vw-wi://rl/N.en-GB.K03589810.wi::35009365.xml?xsl=3
Assembly overview - lock carrier
1 - Carrier for locking mechanism With central locking
and interior release mechanism
Removing and installing → Chapter
2 - Locking rod for door interior opening mechanism
3 - Bearing plate
4 - Exterior handle Removing and
installing → Chapter
5 - Lock operating lever
6 - Lock Removing and
installing → Chapter
7 - Connector
8 - Child-proof control For vehicles with
moulded trim Removing and
installing → Chapter
9 - Trim For vehicles with
moulded trim → General body repairs, interior; Rep. Gr.70.
10 - Bolt Qty. 3 Specified torque 4.5 Nm
11 - Anti-theft protection
12 - Lock cylinder Removing and installing → Chapter Lock cylinder can only be removed outwards in -direction of arrow- from latch carrier.
13 - Operating rod for door interior opening mechanism
14 - Rear lid Removing and installing → Chapter Adjusting → Chapter
Page 1 of 1Assembly overview - lock carrier
22/11/2009vw-wi://rl/N.en-GB.K03589810.wi::35009366.xml?xsl=3
Assembly overview - lock cylinder housingFor vehicles with no inner operating mechanism
1 - Handle
2 - Bolt Qty. 2 20 Nm
3 - Bonnet lock Removing
→ Chapter Installing
→ Chapter
4 - Bolt Qty. 3 Specified
torque 4.5 Nm
5 - Pull rod
6 - Lock cylinder housing Removing
and installing → Chapter
7 - Retaining clip
8 - Pull rod
9 - Central locking control motor Removing:– Separate
connector on control motor
– Unscrew control motor using socket driver -T10010- and unhook out of rear lid.
Installing:– Install in reverse order of removal.
Page 1 of 1Assembly overview - lock cylinder housing
22/11/2009vw-wi://rl/N.en-GB.K03589810.wi::35009367.xml?xsl=3
Removing and installing rear lid lock
Page 1 of 1Removing and installing rear lid lock
22/11/2009vw-wi://rl/N.en-GB.K03589810.wi::35009368.xml?xsl=3
Removing
– Remove rear lid trim → General body repairs, interior; Rep. Gr.70
– Unclip operating rod -1- on latch carrier.
– Unscrew bolts -3- and pull rear lid lock slightly out of rear lid.
– Disconnect connector -4- from lid lock -2-.
– Remove rear lid lock -2- with operating rod -1- from rear lid.
Page 1 of 1Removing
22/11/2009vw-wi://rl/N.en-GB.K03589810.wi::35009369.xml?xsl=3
Installing
– Rear lid lock -2- installation is carried out in reverse order of removal.
– Tighten bolts -3- to 20 Nm.
Note
Operating rod and lid lock must be installed without stress. Before installing rear lid trim and closing rear lid, check function of the lid locking and release components.
Page 1 of 1Installing
22/11/2009vw-wi://rl/N.en-GB.K03589810.wi::35009370.xml?xsl=3
Removing and installing childproof lock operating device
Page 1 of 1Removing and installing childproof lock operating device
22/11/2009vw-wi://rl/N.en-GB.K03589810.wi::35009371.xml?xsl=3
Removing– Remove cover -2-, remove rear lid trim
→ General body repairs, interior; Rep. Gr.70
– Clip the child-safety control lock -3- out of the inner part of the lid -4-.
– Unclip the child-safety control lock -3-out of the inner part of the lid -4--arrow a-.
– Next swing out the child-safety control lock -3- out of the inner part of the rear lid -4-using the extension -1--arrow b-.
Page 1 of 1Removing
22/11/2009vw-wi://rl/N.en-GB.K03589810.wi::35009372.xml?xsl=3
Installing– Swing the child-safety control lock -4- into
the inner part of the lid -5--arrow a-.
– Guide the extension -2- of the child-safety control lock -4- into the carrier part -1--arrow b-.
– Engage the child-safety control lock -4- in the inner part of the lid -5-.
– Remove cover -3- and fit rear lid trim → General body repairs, interior; Rep. Gr.70.
Page 1 of 1Installing
22/11/2009vw-wi://rl/N.en-GB.K03589810.wi::35009373.xml?xsl=3
Removing and installing carrier for rear lid locking
Note
The removal and installation procedures may have to be revised slightly depending on model.
Page 1 of 1Removing and installing carrier for rear lid locking
22/11/2009vw-wi://rl/N.en-GB.K03589810.wi::35009374.xml?xsl=3
Removing– Remove rear lid trim → General body repairs, interior; Rep.
Gr.70
– Remove rear lid lock → Chapter
– Release rods on inner operating mechanism on left-hand side → Chapter
– Disconnect connections -1-.
– Unclip operating rods from latch carrier.
– Unscrew bolts -2- and remove anti-theft protection -3- for lock cylinder.
Page 1 of 4Removing
22/11/2009vw-wi://rl/N.en-GB.K03589810.wi::35009375.xml?xsl=3
– Use screwdriver to lever lock cylinder retaining clip to side, in -direction of arrow-, and remove clip.
– Press left and right locking tabs -arrows- on latch carrier to side and pull latch carrier out a few millimetres from inner part of lid.
– The lock cylinder must remain engaged in the latch carrier.
Note
Before exterior handle can be removed, set lock cylinder to locking position.
– Remove exterior handle -1- without lock cylinder with handle in pulled position -2-.
Page 2 of 4Removing
22/11/2009vw-wi://rl/N.en-GB.K03589810.wi::35009375.xml?xsl=3
– Press centre locking tab on latch carrier -arrow a - back from inner part of lid.
Page 3 of 4Removing
22/11/2009vw-wi://rl/N.en-GB.K03589810.wi::35009375.xml?xsl=3
– Remove latch carrier -1-, together with striker plate, as a single unit from rear lid in -direction of arrow-.
Page 4 of 4Removing
22/11/2009vw-wi://rl/N.en-GB.K03589810.wi::35009375.xml?xsl=3
Installing– Install retaining clip for lock cylinder -
arrow- on exterior handle.
– Further installation is performed in the reverse order of removal.
Note
Ensure that retaining clip -arrow- is correctly engaged in exterior handle.
Ensure that lock cylinder is also set to locking position on installation and that the locking unit is therefore locked. If this is not carried out, the exterior handle cannot be installed properly, and malfunctions occur.
Before installing rear lid trim and closing rear lid, check function of the lid locking and release components.
Page 1 of 1Installing
22/11/2009vw-wi://rl/N.en-GB.K03589810.wi::35009376.xml?xsl=3
Removing and installing lock cylinder
Page 1 of 1Removing and installing lock cylinder
22/11/2009vw-wi://rl/N.en-GB.K03589810.wi::35009377.xml?xsl=3
Removing– Remove rear lid trim → General body repairs, interior; Rep.
Gr.70
– Remove exterior handle → Chapter
– Press lock cylinder -2- in -direction of arrow- out of latch carrier -1-.
Note
Ensure that lock cylinder is set to “locking unit open” position on removal! If this is not carried out, lock cylinder cannot be disengaged from locking unit.
Page 1 of 1Removing
22/11/2009vw-wi://rl/N.en-GB.K03589810.wi::35009378.xml?xsl=3
Installing– Press lock cylinder -2- in -direction of
arrow- into latch carrier -1- from outside.
– Lock cylinder -2- must audibly engage in latch carrier -1-.
– Install exterior handle → Chapter.
Further installation is performed in the reverse order of removal.
Note
Ensure that lock cylinder is also set to “locking unit open” position on installation! If this is not carried out, lock cylinder cannot be engaged in locking unit.
Before installing rear lid trim and closing rear lid, check function of the lid locking and release components.
Page 1 of 1Installing
22/11/2009vw-wi://rl/N.en-GB.K03589810.wi::35009379.xml?xsl=3
Removing and installing lock cylinder housingFor vehicles with no inner operating mechanism
1 - Handle
2 - Guide sleeves
3 - Grip moulding
4 - Seal
5 - Retaining clip
6 - Shaft
7 - Locking ring
8 - Spring
9 - Seal
10 - Lock cylinder housing Removing:– Remove rear
lid trim → General body repairs, interior; Rep. Gr.70.
– Unclip push rod for lid lock (if necessary securing rod for central locking) → Item
– Lever out circlip -5-and remove lock cylinder housing from grip moulding -3-
Installing:– Engage circlip -5- again.– Bring lock cylinder housing into contact with handle trim and engage in handle. Housing can be
heard to lock in place.– Further installation is performed in the reverse order of removal.
11 - Linkage clip For rear lid lock → Item
12 - Linkage clip For control motor → Item
Page 1 of 1Removing and installing lock cylinder housing
22/11/2009vw-wi://rl/N.en-GB.K03589810.wi::35009380.xml?xsl=3
Interior opening mechanism
Page 1 of 1Interior opening mechanism
22/11/2009vw-wi://rl/N.en-GB.K03589810.wi::35009381.xml?xsl=3
Assembly overview1 - Trim
2 - Interior opening mechanism Removing
→ Chapter Installing
→ Chapter
3 - Securing clip for operating rod
4 - Operating rod for door interior opening mechanism
5 - Locking rod for door interior opening mechanism
6 - Lock mechanism
Page 1 of 1Assembly overview
22/11/2009vw-wi://rl/N.en-GB.K03589810.wi::35009382.xml?xsl=3
Removing
– Remove rear lid trim → General body repairs, interior; Rep. Gr.70
– Release retaining clip -5- and unclip interior opening mechanism operating rod -4- from locking unit -3-.
– Unclip locking mechanism linkage -2- from locking unit -3-.
– Lever locking tabs -arrow b- upwards and pull interior opening mechanism -1- from rear lid retainer in -direction of arrow a-.
– Remove interior opening mechanism -1- with locking mechanism linkage from inner part of rear lid.
Page 1 of 1Removing
22/11/2009vw-wi://rl/N.en-GB.K03589810.wi::35009383.xml?xsl=3
InstallingInstallation is the reverse of removal.
Note
Before installing rear lid trim and closing rear lid, check function of the lid locking and release components.
Page 1 of 1Installing
22/11/2009vw-wi://rl/N.en-GB.K03589810.wi::35009384.xml?xsl=3
Removing and installing rear lid seal
Note
During production, a sealant is applied to the rear lid seals, the seal is then placed on the door flange and rolled on.
When seals are removed, the sealant will spread to the inside of the seal and the flanks will be bent out slightly. If the seal is then refitted, a tight seal is not guaranteed.
Therefore each seal which is removed completely should be replaced by a so-called “tap-on” seal.
If a seal has been partially removed, squeeze sides of seal together before installing.
Page 1 of 1Removing and installing rear lid seal
22/11/2009vw-wi://rl/N.en-GB.K03589810.wi::35009385.xml?xsl=3
Removing– Remove interior trim panels (as necessary
and if fitted) → General body repairs, interior; Rep. Gr.70
– Pull rear lid seal -1- off body flange.
Page 1 of 1Removing
22/11/2009vw-wi://rl/N.en-GB.K03589810.wi::35009386.xml?xsl=3
Installing– The vulcanised point -arrow- on the rear lid
seal -arrow- must be aligned to the middle of the rear left light cluster.
– Install interior trim panels (as necessary and if fitted) → General body repairs, interior; Rep. Gr.70
Page 1 of 1Installing
22/11/2009vw-wi://rl/N.en-GB.K03589810.wi::35009387.xml?xsl=3
Rear lid trims
Page 1 of 1Rear lid trims
22/11/2009vw-wi://rl/N.en-GB.k00589832.wi::31322209.xml?xsl=3
ToolsSpecial tools and workshop equipment required
Release lever -T10039-
Pop-rivet nut pliers -V.A.G 1765B-
Page 1 of 1Tools
22/11/2009vw-wi://rl/N.en-GB.k00589832.wi::31322210.xml?xsl=3
Removing and installing window frame trim for rear lid
Page 1 of 1Removing and installing window frame trim for rear lid
22/11/2009vw-wi://rl/N.en-GB.k00589832.wi::31322211.xml?xsl=3
Removing
– Switch off ignition.
– Pull window frame trim -2- off window frame, starting at sides.
Page 1 of 1Removing
22/11/2009vw-wi://rl/N.en-GB.k00589832.wi::31322212.xml?xsl=3
Installing
Note
Before installing, check fasteners -1- for damage and renew if necessary.
– Installation is carried out in reverse order of removal.
Page 1 of 1Installing
22/11/2009vw-wi://rl/N.en-GB.k00589832.wi::31322213.xml?xsl=3
Removing and installing lower rear lid trim
Page 1 of 1Removing and installing lower rear lid trim
22/11/2009vw-wi://rl/N.en-GB.k00589832.wi::31322214.xml?xsl=3
RemovingAll vehicles
– Remove rear lid window frame trim → Chapter.
Only vehicles with additional inner lock in rear lid
Note
On this equipment level the “locking cylinder cover of the child lock” and the “inner lock trim” must also be removed.
– Carefully push “inner lock trim” upwards and pull off trim from panel.
– Insert 2 twist drills (� 1 mm) to depth of 15 mm in openings of “locking cylinder cover for childproof lock”, push drill bits together and pull out cover from mountings.
CautionDamage to rear lid trim.
Trim must be renewed if care is not exercised.
Page 1 of 2Removing
22/11/2009vw-wi://rl/N.en-GB.k00589832.wi::31322215.xml?xsl=3
Carefully release trim around lid lock first.
– When trim is released, continue at corners.
– Do not simply pull trim down, but grasp behind trim with fingers and press against the rear lid with the thumb.
– Once trim is release to the corners, release remainder of trim.
– Remove bolts -3- (Qty 2).
– Hold trim with one hand and remove the pull loop -4- with other hand.
– The trim is now completely free and can be removed.
– Remove the clips that remain in the rear lid using release lever -T10039-.
Page 2 of 2Removing
22/11/2009vw-wi://rl/N.en-GB.k00589832.wi::31322215.xml?xsl=3
Installing
Note
Before installing, check fasteners -1- for damage and renew if necessary. When installing pull loop -4- ensure spacers -2- are seated correctly.
– Installation of the lower trim for the door basically is the reverse of removal.
Tighten bolts -3- to specified torque of 4 Nm.
Page 1 of 1Installing
22/11/2009vw-wi://rl/N.en-GB.k00589832.wi::31322216.xml?xsl=3
Assembly overview - hardboard trim for lower area of rear lid1 - Rear lid
2 - Pop-rivet nut Qty. 2 Insert with
pop-rivet nut pliers -V.A.G 1765B-
3 - Hardboard trim for lower area of rear lid Removing
and installing → Chapter
4 - Clip Qty. 17
5 - Bolt Qty. 2 Specified
torque: 3.5 Nm
6 - Pull loop
7 - Cover for wiper motor
8 - Grommet Qty. 2
Page 1 of 1Assembly overview - hardboard trim for lower area of rear lid
22/11/2009vw-wi://rl/N.en-GB.k00589832.wi::31322217.xml?xsl=3
Removing and installing lower hardboard trim for rear lid
Page 1 of 1Removing and installing lower hardboard trim for rear lid
22/11/2009vw-wi://rl/N.en-GB.k00589832.wi::31322218.xml?xsl=3
Removing
– Unclip wiper motor cover -7- from rear lid.
– Remove bolts -5- and remove pull loop -6-.
– Remove pin using 3 mm hexagon key and pull out spreader rivets -4-
– Remove lower hardboard trim -3- from rear lid -1-.
Page 1 of 1Removing
22/11/2009vw-wi://rl/N.en-GB.k00589832.wi::31322219.xml?xsl=3
Installing
Note
Before installing, check securing clips for damage and renew if necessary.
– Installation is carried out in reverse order of removal.
Page 1 of 1Installing
22/11/2009vw-wi://rl/N.en-GB.k00589832.wi::31322220.xml?xsl=3
Rear window wiper system (vehicles with rear lid)Fault detection and fault display
The convenience system central control unit -J393- is equipped with a self-diagnosis function, which makes fault finding easier.
Use the “guided fault finding” mode on the vehicle diagnosis, testing and information system -VAS 5051- to perform fault finding.
CautionTo disconnect and reconnect the battery, the procedure described in the workshop manual should be strictly adhered to → Chapter.
Page 1 of 1Rear window wiper system (vehicles with rear lid)
22/11/2009vw-wi://rl/N.en-GB.K00589831.wi::33683904.xml?xsl=3
Rear window wiper motor -V12-
Page 1 of 1Rear window wiper motorV12
22/11/2009vw-wi://rl/N.en-GB.K00589831.wi::33683905.xml?xsl=3
Assembly overview
CautionEnsure rubber seals -1- for wiper shaft are seated correctly in door panel.
Apply lubricant: polyethyleneglycol to wiper shaft -6-.
1 - Rubber seal (Use seal with marking pointing upwards with a deviation of -a-= ±10°)
2 - Rear lid3 - Securing nuts4 - Hose connection for windscreen
washer system5 - Rear window wiper motor -V12-6 - Wiper shaft (use polyethyleneglycol as
lubricant during installation)
Page 1 of 1Assembly overview
22/11/2009vw-wi://rl/N.en-GB.K00589831.wi::33683906.xml?xsl=3
RemovingSpecial tools and workshop equipment required
Torque wrench (5 - 50 Nm) -V.A.G 1331-
– Allow rear window wiper to move to park position.
– Disconnect battery → Chapter.
– Unclip cover cap -1- of rear window wiper outwards.
– Remove hexagon nuts -1-.
– Release wiper arm from wiper motor shaft by rocking arm sideways.
– Remove lower rear lid trim → General body repairs, interior; Rep. Gr.70
Page 1 of 2Removing
22/11/2009vw-wi://rl/N.en-GB.K00589831.wi::33683907.xml?xsl=3
– Pull connector -1- off wiper motor.
– Pull off hose connection piece -2- for window washer system.
– Remove hexagon nuts -3-.
– Remove wiper motor -4-.
Page 2 of 2Removing
22/11/2009vw-wi://rl/N.en-GB.K00589831.wi::33683907.xml?xsl=3
InstallingCarry out installation in the reverse sequence, noting the following:
CautionEnsure rubber seal for wiper shaft is seated correctly in door panel
– Insert rubber seal → Anchor.
CautionApply lubricant to the wiper shaft before inserting rear window wiper motor, right wing door -V93-.
– Insert rear window wiper motor, right wing door -V93-→ Anchor.
– Tighten hexagon nuts -3- for wiper motor to 8 Nm.
– Loosely screw wiper arm securing bolt on wiper arm shaft.
– Adjust rear window wiper park position → Chapter.
– Install lower rear lid trim → General body repairs, interior; Rep. Gr.70.
– Reconnect battery → Chapter.
Page 1 of 1Installing
22/11/2009vw-wi://rl/N.en-GB.K00589831.wi::33683908.xml?xsl=3
Removing and installing windscreen wiper bladesRemoving
– Allow windscreen wipers to move to park position.
– Switch off ignition and all electrical consumers and remove ignition key.
– Flap windscreen wiper arm -1-away from windscreen, thereby gripping the wiper blade -2- only at the wiper arm fixation.
Note
Avoid bending the windscreen wiper arm and blade.
Avoid windscreen wiper arm springing back unintentionally and damaging the glass.
– Pull windscreen wiper blade -2-90� to windscreen wiper arm -1-and back again.
– Pull plastic cap off windscreen wiper arm -arrow 1-.
– Remove windscreen wiper blade -2-from axis of windscreen wiper arm -1- in the direction of -arrow 2-.
Installing
– Install the windscreen wiper blade -2- in the reverse sequence.
– Push -arrow 1-windscreen
Page 1 of 2Removing and installing windscreen wiper blades
22/11/2009vw-wi://rl/N.en-GB.K00589831.wi::33683909.xml?xsl=3
wiper blade -2-onto axis of windscreen wiper arm -1-.
– Fasten the windscreen wiper blade by tightening the plastic cap -arrow 2- until the cap notches.
– Push windscreen wiper arm back onto window.
– Check windscreen wiper blade park position and if necessary, adjust → Chapter.
Page 2 of 2Removing and installing windscreen wiper blades
22/11/2009vw-wi://rl/N.en-GB.K00589831.wi::33683909.xml?xsl=3
Adjusting rear window wiper park positionSpecial tools and workshop equipment required
Torque wrench (5 - 50 Nm) -V.A.G 1331-
– Allow wiper to move to park position.
Distance -a- between wiper blade and lower edge of window should be 25 mm.
– If necessary, adjust rear window wiper blade park position by moving wiper arm on shaft.
– Tighten securing nut of wiper arm to specified torque of 12 Nm.
Page 1 of 1Adjusting rear window wiper park position
22/11/2009vw-wi://rl/N.en-GB.K00589831.wi::33683910.xml?xsl=3
Rear window washer system (vehicles with rear lid)Fault detection and fault display
The convenience system central control unit -J393- is equipped with a self-diagnosis function, which makes fault finding easier.
Use the “guided fault finding” mode on the vehicle diagnosis, testing and information system -VAS 5051- to perform fault finding.
CautionTo disconnect and reconnect the battery, the procedure described in the workshop manual should be strictly adhered to → Chapter.
Page 1 of 1Rear window washer system (vehicles with rear lid)
22/11/2009vw-wi://rl/N.en-GB.K00589831.wi::33683911.xml?xsl=3
Assembly overview - rear window washer system (vehicles with rear lid)1 - Spray jet for
rear window washer system– Integrated in
drive shaft of rear wiper motor
Removing and installing → Chapter
Adjusting → Chapter
2 - Connection piece Connection
to rear window spray jet
Overview of hose couplings for washer fluid lines → Chapter
3 - Connection piece Separating
point between roof wiring harness and rear lid wiring harness
Overview of hose couplings for washer fluid lines → Chapter
4 - Hose Hose repair → Chapter
5 - Angled piece Connection to windscreen and rear window washer pump– Colour of connection to windscreen spray jets - black– Colour of connection to rear window spray jet - white Overview of hose couplings for washer fluid lines → Chapter
6 - Windscreen and rear window washer pump -V59- Removing and installing → Chapter
7 - Reservoir for windscreen and headlight washer system
Page 1 of 2Assembly overview - rear window washer system (vehicles with rear lid)
22/11/2009vw-wi://rl/N.en-GB.K00589831.wi::33683912.xml?xsl=3
Size of reservoir depends on whether vehicle has headlight washer system Removing and installing → Chapter
8 - Filler pipe for reservoir for windscreen washer and headlight washer system Removing and installing filler pipe → Chapter
Page 2 of 2Assembly overview - rear window washer system (vehicles with rear lid)
22/11/2009vw-wi://rl/N.en-GB.K00589831.wi::33683912.xml?xsl=3
Renewing washer spray jet
Page 1 of 1Renewing washer spray jet
22/11/2009vw-wi://rl/N.en-GB.K00589831.wi::33683913.xml?xsl=3
Removing– Allow rear window wiper to move to park position.
– Unclip cover cap -1- of rear window wiper outwards.
– Using suitable long-nose pliers, carefully pull out washer spray jet in -direction of arrow-.
Page 1 of 1Removing
22/11/2009vw-wi://rl/N.en-GB.K00589831.wi::33683914.xml?xsl=3
InstallingInstall in reverse order of removal.
Page 1 of 1Installing
22/11/2009vw-wi://rl/N.en-GB.K00589831.wi::33683915.xml?xsl=3
Adjusting washer spray jetAdjusting washer spray jet → Booklet19.1
Page 1 of 1Adjusting washer spray jet
22/11/2009vw-wi://rl/N.en-GB.K00589831.wi::33683916.xml?xsl=3
Windscreen wash/wipe system and headlight washer system: Check function and settings Check anti-freeze concentration of Windscreen Clear with
anti-freeze -G 052 164-, replenish with fluid if necessary → Chapter.
Windscreen wash/wipe system: Check spray jet settings and adjust if necessary → Chapter.
Headlight washer system: Check spray jet settings, adjust if necessary → Chapter
Checking Windscreen Clear with anti-freeze of windscreen wash/wipe system, replenishing with fluid if necessaryChecking anti-freeze concentration
Special tools and workshop equipment required
Refractometer -T10007-
Read precise value for the following tests at bright/dark boundary. Using a pipette, place a drop of water on the glass to improve the readability of the bright/dark boundary. The bright/dark boundary can be clearly recognised on the “WATERLINE”.
– Check concentration of anti-freeze additive using refractometer -T10007- (refer to operating instructions).
The scale -1- of the refractometer is calibrated for Genuine Volkswagen Windscreen Clear with anti-freeze -G 052 164-.
The scale -2- is designed for commercially available windscreen cleanser as well as a mixture of commercially available windscreen cleanser and genuine Volkswagen Windscreen Clear with anti-freeze -G 052 164-.
Mixture ratio
Frost protection to Windscreen Clear with anti-freeze
Water
Page 1 of 5Windscreen wash/wipe system and headlight washer system: Check function and setti...
22/11/2009vw-wi://igg/N.en-GB.k00589828.wi::34012073.xml?xsl=3
G 052 164
-17/-18 °C 1 part 3 parts
-22/-23 °C 1 part 2 parts
-37/-38 °C 1 part 1 part
Replenishing with fluid
The fluid reservoir of the window washer system must be filled completely.
Starting immediately, use only Genuine Volkswagen Windscreen Clear with anti-freeze -G 052 164- all-year-round when replenishing windscreen wash/wipe system.
Note
All vehicles having fan-type spray jets, the reservoir must be filled with Windscreen Clear with anti-freeze -G 052 164-, as this fluid has a low viscosity at temperatures below freezing. Otherwise the complicated spray jet system can become blocked by the crystallised washer fluid, which affects the spray pattern of the spray jet. Windscreen Clear with anti-freeze -G 052 164- ensures that the fan-type spray jets remain fully functional also at low temperatures.
Genuine Volkswagen Windscreen Clear with anti-freeze -G 052 164- protects the spray jets, fluid reservoir and connecting hoses from freezing.
Use Genuine Volkswagen Windscreen Clear with anti-freeze -G 052 164- in the warmer periods of the year also. The powerful cleanser removes wax and oil residue from the glass.
Frost protection must be guaranteed to approx. -25 °C (approx. -35 °C in countries with an arctic climate) in the windscreen wash/wipe system.
Windscreen wash/wipe system: Check spray jet settings and adjust if necessarySpecial tools and workshop equipment required
Setting device -T10127 -equipped with needle 3125/5 A
Note
The spray jets may be cleaned in both directions, also opposite to direction of spray with compressed air or water.
Never use a needle or similar object, as otherwise water passages in spray jets will be damaged!
Windscreen spray jet settings:
Page 2 of 5Windscreen wash/wipe system and headlight washer system: Check function and setti...
22/11/2009vw-wi://igg/N.en-GB.k00589828.wi::34012073.xml?xsl=3
The washer jets are preset. However, small height differences can be compensated for.
– If both spray fields are not at same height, adjust spray direction upwards or downwards as follows:
– Adjust the spray jet at adjuster -1- by hand.
Rear window spray jet setting / tailgate:
– Remove cap above drive shaft -2-.
– Adjust spray jet -1- using adjusting tool -T10127 - so that the water jet sprays onto the upper third of rear window.
Rear window spray jet setting / rear wing doors:
Page 3 of 5Windscreen wash/wipe system and headlight washer system: Check function and setti...
22/11/2009vw-wi://igg/N.en-GB.k00589828.wi::34012073.xml?xsl=3
– Adjust spray jet using adjusting tool -T10127 - so that the water jets spray onto rear window at positions shown.
Note
Mark the points at which water strikes the window with a water-soluble pin.
Dimension a = approx. 150 mm Dimension b = approx. 250 mm
Headlight washer system: Check spray jet settings, adjust if necessarySpecial tools and workshop equipment required
Adjusting tool -T10167-
The jet adjustment dimensions are for the left-hand headlight (right-hand headlight mirror image)
Checking jet setting
– Switch on dipped headlight.
– Operate windscreen washer system.
The headlights are washed if the windscreen wiper lever is hold in “Wipe position” for at least 1.5 seconds.
The spray jet should spray on the positions illustrated.
Adjusting jets
– Switch on dipped headlight.
– Operate windscreen washer system.
The headlights are washed if the windscreen wiper lever is hold in “Wipe position” for at least 1.5 seconds.
The spray jets -arrows- are extended.
Page 4 of 5Windscreen wash/wipe system and headlight washer system: Check function and setti...
22/11/2009vw-wi://igg/N.en-GB.k00589828.wi::34012073.xml?xsl=3
– Perform the following procedure:
– Align the spray direction of respective jet using adjusting tool -T10167- at points illustrated.
Note
Mark the points at which water strikes the headlight with a water-soluble pin.
“a” approx. 127 mm “b” approx. 236 mm “c” approx. 100 mm “d” approx. 88 mm
Note
If stream of water is uneven or cannot be adjusted to specified dimensions, renew washer jet (repair measure).
Page 5 of 5Windscreen wash/wipe system and headlight washer system: Check function and setti...
22/11/2009vw-wi://igg/N.en-GB.k00589828.wi::34012073.xml?xsl=3
High level brake light bulb -M25-
Page 1 of 1High level brake light bulbM25
22/11/2009vw-wi://rl/N.en-GB.K00589831.wi::33683997.xml?xsl=3
Rear lid
Page 1 of 1Rear lid
22/11/2009vw-wi://rl/N.en-GB.K00589831.wi::33683998.xml?xsl=3
Removing and installing high-level brake light -M25-Removing
– Switch off ignition and all electrical consumers and remove ignition key.
– Remove upper rear lid trim → General body repairs, interior; Rep. Gr.70.
– Remove securing bolts -arrows-.
– Lift bulb for high-level brake light -M25-and loosen 2-pin connector -arrow-.
Installing
Installation is carried out in the reverse sequence. Observe specified torque of 1.5 Nm.
Page 1 of 1Removing and installing high-level brake lightM25
22/11/2009vw-wi://rl/N.en-GB.K00589831.wi::33683999.xml?xsl=3
Renewing bulbs/ light emitting diodes (LED)
Note
The high-level brake light -M25- must be replaced as a complete unit in the event of repairs.
Page 1 of 1Renewing bulbs/ light emitting diodes (LED)
22/11/2009vw-wi://rl/N.en-GB.K00589831.wi::33684000.xml?xsl=3
Roof trims
Page 1 of 1Roof trims
22/11/2009vw-wi://rl/N.en-GB.k00589832.wi::31322221.xml?xsl=3
ToolsSpecial tools and workshop equipment required
Release lever -T10039-
Torque wrench -V.A.G 1783-
Page 1 of 1Tools
22/11/2009vw-wi://rl/N.en-GB.k00589832.wi::31322222.xml?xsl=3
Removing and installing roof frame trim
Page 1 of 1Removing and installing roof frame trim
22/11/2009vw-wi://rl/N.en-GB.k00589832.wi::31322223.xml?xsl=3
Removing
– Open rear lid.
– Remove upper D-pillar trim → Chapter.
– Pull roof frame trim -1- downwards out of mountings in roof cross member -4- and out of beading of rear lid seal -2-.
Page 1 of 1Removing
22/11/2009vw-wi://rl/N.en-GB.k00589832.wi::31322224.xml?xsl=3
Installing
Note
Before installing, check fasteners -3- for damage and renew if necessary. After installing, check that roof frame trim -1- is completely in beading of rear lid seal -2-.
– Installation is carried out in reverse order of removal.
Page 1 of 1Installing
22/11/2009vw-wi://rl/N.en-GB.k00589832.wi::31322225.xml?xsl=3
Assembly overview - roof frame trim
Note
Depending on model slight differences are possible when referring to assembly overview.
1 - Roof frame trim Without right
and left sliding door.
2 - Roof frame trim With right
and left sliding door.
3 - Channel
4 - Securing clip At front and
rear only.
5 - Clip For roof
frame trim without sliding door.
Qty. 6
6 - Clip For roof
frame trim with sliding door.
Qty. 5
Page 1 of 1Assembly overview - roof frame trim
22/11/2009vw-wi://rl/N.en-GB.k00589832.wi::31322226.xml?xsl=3
Assembly overview - moulded headlining (Multivan)1 - Front seat area
moulded headlining
Removing → Chapter
2 - Bolts
Qty. 2, specified torque 2 Nm
3 - Passenger compartment moulded headlining
Removing → Chapter
4 - Securing clip
Qty. 8
5 - Clip holder
Page 1 of 1Assembly overview - moulded headlining (Multivan)
22/11/2009vw-wi://rl/N.en-GB.k00589832.wi::31322227.xml?xsl=3
Removing and installing moulded headlining for passenger compartment
Note
Removal and installation is described for the Multivan. Follow same instructions for the Transporter as appropriate.
Page 1 of 1Removing and installing moulded headlining for passenger compartment
22/11/2009vw-wi://rl/N.en-GB.k00589832.wi::31322228.xml?xsl=3
Removing– Remove middle interior lights → Electrical system; Rep. Gr.96.
– Remove rear interior lights → Electrical system; Rep. Gr.96.
– Remove grab handles (B-pillar) → Chapter.
– Remove upper B-pillar trim (belt end anchors need not be removed) → Chapter.
– Remove retainers for net partition → Chapter.
– Remove upper C-pillar trim → Chapter.
– Remove upper D-pillar trim → Chapter.
– Remove rear roof frame trim → Chapter.
– Remove middle and rear roof grab handles → Chapter.
– Pull air duct hose -2- off air duct -1- on moulded headlining -3--arrow-.
– Lower rear section of moulded headlining -3- slightly and pull it to rear out of the clips.
– Pull moulded headlining -3- to rear out of vehicle.
Page 1 of 1Removing
22/11/2009vw-wi://rl/N.en-GB.k00589832.wi::31322229.xml?xsl=3
Installing– Remove the 8
clips -1- from the roof bows and insert then into the clip holders -2- (on back of moulded headlining).
– Position passenger compartment moulded headlining in installation position and clip into the roof.
– Further installation is performed in the reverse order of removal.
Page 1 of 1Installing
22/11/2009vw-wi://rl/N.en-GB.k00589832.wi::31322230.xml?xsl=3
Removing and installing moulded headlining in area of front seats
Note
Removal and installation is described for the Multivan. Follow same instructions for the Transporter as appropriate.
Page 1 of 1Removing and installing moulded headlining in area of front seats
22/11/2009vw-wi://rl/N.en-GB.k00589832.wi::31322231.xml?xsl=3
RemovingOnly vehicles with a sunroof
– Remove passenger compartment moulded headlining → Chapter.
– Remove operating unit in roof console → Electrical system; Rep. Gr.96.
– Remove roof console → Chapter.
– Remove sun visors → Chapter.
– Remove vanity mirror light → Electrical system; Rep. Gr.96.
Page 1 of 2Removing
22/11/2009vw-wi://rl/N.en-GB.k00589832.wi::31322232.xml?xsl=3
– Remove grab handles (A-pillar) → Chapter.
– Remove A-pillar trims → Chapter.
– Push wedge -T10039/1- between frame -1- and moulded headlining -2-.
– Using release lever -T10039-, move along edges of moulded headliner and unclip headliner from frame -arrow-.
All vehicles
– Remove the 2 bolts -1-, specified torque 2 Nm.
– Remove front roof grab handles → Chapter.
– Pull front seat area moulded headlining to side out of vehicle.
Page 2 of 2Removing
22/11/2009vw-wi://rl/N.en-GB.k00589832.wi::31322232.xml?xsl=3
Installing– Installation is carried out in reverse order of removal.
Page 1 of 1Installing
22/11/2009vw-wi://rl/N.en-GB.k00589832.wi::31322233.xml?xsl=3