-
Product Data SheetVersion 19/02/2008
Sika® -101a
Sika® -101a 1/2D08897050208E
Waterproofing Slurry and Moisture Seal
Description An easy to use cement based powder containing
waterproofingadditives. After mixing with water into a slurry
consistency, it is appliedto concrete substrates to seal against
water infiltration.
Uses Sika®-101a seeks out and blocks the pores in concretes
structuressuch as:- Basements- Culverts- Inspection-chambers-
Manholes- Water-tanks- Reservoirs
Advantages Sika®-101a provides the following beneficial
properties in post applied waterproofing:- Impermeable- Good
adhesion to sound concrete- Allows the substrate to "breath"-
Non-toxic- Chloride free
Recommended Consumption - For ordinary water conditions : a
minimum 2 coats at 1 kg/m2/coat ofSika®-101a should be applied.-
For high water pressure a total thickness of 2 mm. or approximately
4 kg/m2
is recommended.
Instructions for Use
Surface Preparation Concrete surface must be clean, sound, level
and uncontaminated by oilor grease. Remove cement laitance,
formwork traces and loosely adheringparticles by sandblasting or
high-pressure water jet. Make good honey-combing and other
imperfections with cement mortar. Wet surface untilsaturated.
Mixing Add powder to given amount of water, and stir with a low
speed mixer for5 minutes until a lump free smooth consistency is
achieved.
Application Use a medium-hard brush with plastic bristles,
trowel or mortar sprayingmachine. In each case after applying, the
slurry must be worked well into thesurface. Repeat for second
coat.
Cons
truc
tion
-
Sika -101a® 2/2
Important Recommendations Protect from rain, strong winds and
direct sunshine. Keep moist for first3-4 days, after application.
Protect slurry in pedestrian areas by overlayingwith 3:1 sand :
cement screed.
Technical Data
Dry Mix
Form Powder
Colour Grey
Storage Conditions Dry, protect from moisture
Shelf Life 12 months when unopened
Packaging 5 kg, 20 kg bags
Wet Mortar Approx 1.25 ltrs. water per box 5 kg.Mixing Ratio or
Approx 5.0 ltrs. water per bag 20 kg.
Density 1.95 kg/litre
Working Temperature Not less than 5oC
Pot Life 25-30 minutes at 230C
Hardened Mortar
Young's Modulus 20 KN/mm2 after 28 days at 20oC/65%RH
Water-Vapour 50 (approx.)Permeability Factor µ
Compressive Strength > 30 N/mm2 (28 days)
Flexural Strength 8.5 N/mm2
Bond Strength to Concrete 1.0-1.5 N/mm2 (concrete failure)
Tel : +66 3821 4270-85Fax : +66 3821 4286E-mail :
[email protected] site : http//www.sika.co.th
Sika (Thailand) LimitedHead Office700/37 Moo 5 Bangpakong
Industrial Park II,Km.57 Bangna-Trad Rd., T. Klongtamhru,Muang
District, Cholburi 20000
The information, and, in particular, the recommendations
relating to the application and end-use of Sika products, are given
in good faith based on Sika’s currentknowledge and experience of
the products when properly stored, handled and applied under normal
conditions in accordance with Sika’s ecommendations.In practice,
the differences in materials, substrates and actual site conditions
are such that no warranty in respect of merchantability or of
fitness for a particularpurpose, nor any liability arising out of
any legal relationship whatsoever, can be inferred either from this
information, or from any written recommendations,or from any other
advice offered. The user of the product must test the product’s
suitability for the intended application and purpose. Sika reserves
the rightto change the properties of its products. The proprietary
rights of third parties must be observed. All orders are accepted
subject to our current terms of saleand delivery. Users must always
refer to the most recent issue of the local Product Data Sheet for
the product concerned, copies of which will be suppliedon
request.
-
Product Data SheetVersion 05/10/2018
Sika® -102
Sika® -102 1/3D09597041018E
Waterplug
Description Sika® -102 is a chloride free, ready for use powder.
When mixed with water,it becomes a powerful, fast-setting permanent
waterplug.
Technical Data
Specific gravity 1.99of Sika® -102 paste(W/102 = 25%)
pH value of Sika 102 11paste
Packaging 1 kg, 4.5 kg/can 5 kg, 15, 25 kg/bag
Shelf Life 6 months max. If kept dry in original container
Advantages - Easy to use, easy to mix, just add water.- No
special equipment required.- Very fast setting with rapid strength
development.- Permanent.- Good adhesion to all substrates.-
Remarkable water-stopping power and hydraulic resistance.- No
cracking, practically no shrinkage.- No corrosion.
Uses Ready for use waterplug to stop pressure leaks and seepage
through rockand concrete, as well as through joints between
concrete and steel (bolt surroundings, ducts, sheetpiles etc.) in
subways, culverts, tunnels, dams,basements, pools.
Cons
truc
tion
-
Mixing/Hardening Time By weight
Sika® -102 1 kg
Water Approx. 0.2 ltr.
Relation between temperature and hardening time.
Compressive-Flexural-and Tensile Strengths
120
100
200
300
400
500
600
100
80
10 min. 1 hr. 6 hrs. 1 day 7 days 28 days
1020
40
60
CompressiveStrength
FlexuralStrength
TensileStrength
kg./cm2
Sika® -102 2/3
sec.
100
200
5 10 15 20 25 30 oC
-
Sika® -102 3/3
Application Cut concrete or rock in "V" shape around the leaking
point. Removeall chippings, unsound and loose particles and clean
surface withwater prior to application of Sika® -102.
Fill freshly prepared Sika® -102 into the V-shaped cut, starting
outsideand work towards the center of the leak (plug minor leaks
first). Holdmaterial in place, and then strike off flush with
surface.
If water pressure is very high, It is recommended to use wooden
plugfirst, which is then covered and secured with Sika® -102.
V Cut
Caution 1. It is recommended to prepare Sika® -102 in small
quantities at a time.If mixed in large amounts, hardening may have
occured before it iscompletely used.
2. Do not mix Sika® -102 with other admixtures, cements or
sand.3. Sika® -102 is hygroscopic. Seal unused quantity immediately
in
original container.4. Sika® -102 is alkaline. Use rubber gloves
when working with Sika® -102.
If Sika® -102 gets into eyes, clean out immediately with fresh
water.
1. 2. 3.
4.
Sika® -102
Sika® -102
Tel : +66 3810 9500Fax : +66 3821 4286E-mail :
[email protected] site : http//www.sika.co.th
Sika (Thailand) LimitedHead Office700/37 Moo 5 Bangpakong
Industrial Park II,Km.57 Bangna-Trad Rd., T. Klongtamhru,Muang
District, Cholburi 20000
The information, and, in particular, the recommendations
relating to the application and end-use of Sika products, are given
in good faith based on Sika’s currentknowledge and experience of
the products when properly stored, handled and applied under normal
conditions in accordance with Sika’s ecommendations.In practice,
the differences in materials, substrates and actual site conditions
are such that no warranty in respect of merchantability or of
fitness for a particularpurpose, nor any liability arising out of
any legal relationship whatsoever, can be inferred either from this
information, or from any written recommendations,or from any other
advice offered. The user of the product must test the product’s
suitability for the intended application and purpose. Sika reserves
the rightto change the properties of its products. The proprietary
rights of third parties must be observed. All orders are accepted
subject to our current terms of saleand delivery. Users must always
refer to the most recent issue of the local Product Data Sheet for
the product concerned, copies of which will be suppliedon
request.
-
Product Data SheetVersion 13/01/2014
SikaProof Membrane
SikaProof Membrane 1/2D04798080114E
One Component Elastic Waterproofing Cold Applied Liquid
Membrane
Description SikaProof Membrane is an one component water bases
flexible polymer modified acrylic bitumen waterproofing emulsion
cold applied liquid membrane
Advantages Single-component, ready to use. Easily applied by
spray roller or brush. Fast curing to a durable, flexible coating.
Excellent adhesive and elongation properties. Designed to be used
on new and existing structures. Contains no solvents. Can be
applied on slightly damp concrete.
Coverage 1.2 kg/m2 The required amount will depend on the type
of structures. Three or four coats are generally necessary.
Uses Below grade waterproofing of concrete and masonry surface
Basements etc. Concrete roof waterproofing Underground roof slabs
of tunnel Planter boxes and gutters
Instruction for UseSurface Preparation The concrete substrate
must be clean, sound, free from any surface contaminants i.e.
grease, wax based curing compound, oil, dirt, dust and surface
laitance.
Priming Prime the prepared surface with a mixture of 1 part of
SikaProof Membrane and 2 parts of water at the rate of 0.2 litre/m2
(of undiluted product) and allow to dry.
Cons
truc
tion
Application ConcreteRoofWaterproofingSystem On the dry priming
coat, apply by brush, roller or spray the 1st coat of SikaProof
Membrane at the rate of 0.4 ltr. /m2 and allow to dry. Apply the
2nd coat at the same rate.
Lay SikaLastic® Fleece -120 inon the wet 2nd coat of SikaProof
Mem brane.
SikaProof Membrane 3rd coat is applied at the rate of 0.6
ltr./m2 and allowed to dry. Finally SikaProof Membrane 4th coat is
applied at the rate of 0.4 ltr./m2
and allowed to dry.
-
Cons
truct
ion
SikaProof Membrane 2/2
Limitation Not to be used as a traffic bearing surface. Do not
thin with solvents. Application temperature 5°C - 50°C .
Safety and Handling SikaProof Membrane is not a hazardous
product. In case of contact with Instructions eyes , flush
immediately with water and contact a physician. Clean hands and
tools with water when wet or strong solvents when dry.
Treatmentsofcrackedsurfaceandconstructionjoint We recommend that
a sealant, such as Igas Black to be used to seal
the cracks and construction joint prior to apply SikaProof
Membrane. The use of SikaLastic® Fleece -120 can be advisable as
well. Please
consult our Technical Department for details.
GeneralWaterproofingSystem The system consists of : SikaProof
Membrane primer, which is a mixture of 1 part of material and 2
volume of water is applied at the rate of application is 0.2
ltr./m2 of SikaProof Membrane. 3 coats of SikaProof Membrane are
applied at the rate of 0.4 ltr./m2/ each coat. Allow the coat to
dry between applications.
ProtectionofWaterproofingSystem A cement and sand screed
(generally. 30 mm. thick) shall be applied on
to the SikaProof Membrane where mechnical damage during
subsequent construction work or when in service is anticipated.
Technical Data Color Black (once Dry)
Density ≈ 1 kg./litre Dry Time (Touch Dry) 1-2 hours
Storage Store in shade under house conditions and keep away from
sources of heat. Not below 5OC, protected from high temperature.
Storage must be carefully controlled as all last systems may
coagulate in
high temperatures.
Shelf life 6 months in original, unopened container.
Packaging 20 Kg. pail Crack Bridging property Hairline cracks.
(unreinforced)(Tested at -1OC)
The information, and, in particular, the recommendations
relating to the application and end-use of Sika products, are given
in good faith based on Sika’s current knowledge and experience of
the products when properly stored, handled and applied under normal
conditions in accordance with Sika’s ecommendations. In practice,
the differences in materials, substrates and actual site conditions
are such that no warranty in respect of merchantability or of
fitness for a particular purpose, nor any liability arising out of
any legal relationship whatsoever, can be inferred either from this
information, or from any written recommendations, or from any other
advice offered. The user of the product must test the product’s
suitability for the intended application and purpose. Sika reserves
the right to change the properties of its products. The proprietary
rights of third parties must be observed. All orders are accepted
subject to our current terms of sale and delivery. Users must
always refer to the most recent issue of the local Product Data
Sheet for the product concerned, copies of which will be supplied
on request.
Tel : +66 3821 4270-85Fax : +66 3821 4286E-mail :
[email protected]
Sika (Thailand) LimitedHead Office700/37 Moo 5 • Amata Nakorn
EstateBangna-Trad KM.57 • Tambol Klong TamhruMuang District •
Chonburi • Thailand 20000
-
Cons
truct
ion
SikaTop® Seal -107 1/4
D09497141018E
SikaTop® Seal -107Two Component Cementitious Slurry for
Waterproofingand Damp Poofing
Product Description
SikaTop® Seal -107 is a two part polymer modified cementitious
waterproof mortar slurry comprising of a liquid polymer and a
cement basedmix incorporating special admixtures.SikaTop® Seal -107
suitable for drinking water, wet room and swimming pool system.
Uses SikaTop® Seal -107 is used for:�� Interior and exterior
waterproofing and damp-proofing of concrete, cementitious
rendering, brickwork and blockwork�� Cementitious waterproofing for
drinking and portable water, wet room and swimming pool system��
Rigid waterproofing of basement walls in new construction and
refurbishment�� Pore / blowhole filling�� Waterproofing basement��
Sealing fine “hairline” cracks in concrete structures (not subject
to movement)�� Levelling mortar for concrete repair works
Characteristics / Advantages
�� Easy to apply by brush, thin trowel applications�� No water
required�� Prebatched components�� Hand or spray applied�� Easy and
fast mixing�� Very good adhesion�� Protects concrete against
carbonation�� Protects against water penetration�� Non-corrosive to
steel or iron�� Approved for potable water contact
TestsApproval / Standards Water quality test report from water
quality control division, Provincial
Water Works Authority of Thailand.
Product Data SheetVersion 17/10/2018 (Corporate : Edition
01/2010)
-
FormAppearance/ Colours Part A: white liquid
Part B: grey or white powderMixed product: cement grey or
off-white
Packaging 25 kg / set Component A: 4.55 kg / pail Component B:
20.45 kg / bag5 kg / set Component A: 0.9 kg / pail Component B:
4.1 kg / bag
StorageStorage Conditions/ Shelf Life
6 months (25 kg / set)9 months (5 kg / set)Commencing from date
of production if stored properly in undamaged and unopened original
sealed packaging in dry and cool conditions. Liquid component must
be protected from frost.
Technical DataChemical Base Part A: liquid polymer and
additive
Part B: portland cement selected aggregate and admixtures
Density Fresh mortar density: ~ 2.00 kg/ lDry density: ~ 1.4 kg
/ m3 (TIS 1505 - 2541)
Layer Thickness 0.75 mm min.2 mm max.
Mechanical / Physical PropertiesCompressive Strength (ASTM
C109)
7 days 20 MPa28 days 30 MPa
Bond Strength 0.7 MPa (To Concrete at 28 days) (ASTM
C952-02)
Water Absorption 2.6% (at 28 days) (ASTM C121-90 (Reapproved
1999))
System InformationApplication DetailsConsumption Dependent on
the substrate roughness, surface profile and thickness of
the layer applied.As a guide, ~ 2.0 kg / m2 / mm (excluding
allowances for loss wastage,surface profile and porosity, etc.).1
unit of 25 kg yields ~ 12.5 L of mortar.
Substrate Quality The substrate must be structurally sound and
free of all traces of contaminants, loose and friable particles,
cement laitance, oils and grease etc.The concrete “pull off”
(tensile adhesive) strength must be > 1.0 N / mm2.
SikaTop® Seal -107 2/4
-
Substrate Preparation General:The substrate must be prepared by
suitable mechanical preparationtechniques such as high pressure
water jetting, needle guns, blastcleaning,scabblers etc. and
properly pre-wetted to a saturated surface dry condition.For pore /
blowhole filling:Blastclean to remove all contaminants including
from within the pores /blowholes.As a levelling mortar:Prepare and
clean all surfaces by suitable mechanical means such as abrasive
blast cleaning or equivalent to ensure cement laitance, surface
contamination and all existing coatings are removed and all
blowholes and honeycombed areas are exposed. The resultant surface
must be profiled to achieve maximum bond strength.
Application Conditions /LimitationsSubstrate Temperature +8°C
min. / +35°C max.
Ambient Temperature +8°C min. / +35°C max.
Application InstructionsMixing Used as slurry: A : B = 1 : 4
(parts by weight)
Used as mortar: A : B = 1 : 4.5 (parts by weight)
Mixing Time ~ 3 minutes
Mixing Tools SikaTop® Seal -107 must be mechanically mixed using
a forced actionmixer or in a clean drum using a drill and paddle
(max. 500 rpm). A normalconcrete free fall mixer is NOT
suitable.
Application Method /Tools
Shake part A before using it. Pour approximately half of part A
into themixing container and add part B slowly while mixing. Add
the remainderof part A and continue mixing until a uniform lump
free consistency isachieved. The surface must be pre-wetted to a
saturated surface drycondition before application.As a slurry:Apply
the mixed SikaTop® Seal -107 either mechanically by spray or byhand
using a stiff brush. Applied in the same direction.Apply the 2nd
coat of SikaTop® Seal -107, applied by brush in crosswisedirection
to the first application as soon as first coat has hardened.As a
mortar:When SikaTop® Seal -107 is applied by trowel (e.g. for a
smooth surface finish), the product must be mixed with a 10%
reduction of part A (~ 1 A : 4.5 B).Apply the 2nd coat of SikaTop®
Seal -107 as soon as the first coat hashardened. For pore /
blowhole filling, tightly trowel into the pores / blowholes of the
surface.
Cleaning of Tools Clean all tool and application equipment with
clean water immediately after use.Hardened / cured material can
only be removed mechanically
Pot Life ~ 30 minutes at +20°C
SikaTop® Seal -107 3/4
-
Cons
truct
ion
The information, and, in particular, the recommendations
relating to the application and end-use of Sika products, are given
in good faith based on Sika’s current knowledge and experience of
the products when properly stored, handled and applied under normal
conditions in accordance with Sika’s ecommendations. In practice,
the differences in materials, substrates and actual site conditions
are such that no warranty in respect of merchantability or of
fitness for a particular purpose, nor any liability arising out of
any legal relationship whatsoever, can be inferred either from this
information, or from any written recommendations, or from any other
advice offered. The user of the product must test the product’s
suitability for the intended application and purpose. Sika reserves
the right to change the properties of its products. The proprietary
rights of third parties must be observed. All orders are accepted
subject to our current terms of sale and delivery. Users must
always refer to the most recent issue of the local Product Data
Sheet for the product concerned, copies of which will be supplied
on request.
Tel : +66 3810 9500Fax : +66 3821 4286E-mail :
[email protected]
Sika (Thailand) LimitedHead Office700/37 Moo 5 • Amata Nakorn
EstateBangna-Trad KM.57 • Tambol Klong TamhruMuang District •
Chonburi • 20000 Thailand
Waiting Time /Overcoating
Waiting time between coats10°C ~ 12 hours20°C ~ 6 hours30°C ~ 3
hours
If waiting time period exceeds 24 hours, lightly blastclean the
surface.SikaTop® Seal -107 can be overpainted using solvent based
primers orcoatings. SikaTop® Seal -107 must cure for a minimum of 7
days beforeovercoating.
Notes on Application /Limitations
SikaTop® Seal -107 is not a decorative treatment and may display
signsof “blooming” after rain or in damp weather. This does not
affect theperformance of the coating, in any way. Where SikaTop®
Seal -107 willbe visible after completion of the works, then the
off-white colour, whichis aesthetically more pleasing, should be
used.Avoid application in direct sun and/or strong wind. Do not add
water inany circumstances. Apply only to sound, prepared
substrates. Do notexceedmaximum layer thickness.For waterproofing
or damp proofing application, always use at least 2 coats to give a
total thickness of between 1.5 to 2.0 mm. In areas of severe water
penetration, three coats might be required.Protect freshly applied
material from freezing conditions and rain etc.For waterproofing /
damp-proofing works, special attention is requiredto avoid
puncturing the waterproof coating with fixings. These must
beaccommodated by surface bonding with either Sikadur® -31 CF
Normalor Sikaflex® Construation (AP) etc.When used in contact with
drinking structures, ensure that all associatedSika® products and
construction materials also comply with the localregulations for
drinking water contact.
Curing DetailsCuring Treatment It is essential to cure SikaTop®
Seal -107 immediately after application for
a minimum of 3 to 5 days to ensure full cement hydration and to
minimisecracking.Use polythene sheeting or similar approved
methods.
Value Base All technical data stated in this Product Data Sheet
are based on laboratory tests.Actual measured data may vary due to
circumstances beyond our control.
Health and Safety Information
For information and advice on the safe handling, storage and
disposal ofchemical products, users shall refer to the most recent
Material Safety Data Sheet containing physical, ecological,
toxicological and other safety-related data.
SikaTop® Seal -107 4/4
Sika PDS_E_Sika -101aSika PDS_E_Sika -102 (Waterplug)Sika
PDS_E_SikaProof MembraneSika PDS_E_SikaTop Seal-107
