USER’S MANUAL | WARRANTY CARD

ANALOG WATCHESwith sterling silver 925 watch case, Swiss quartz movement

and sapphire glass

MANUFACTURE:

WENCIA LUXURY GROUP SAImporter:

www.wencia.ch | www.wencia.com

4 5

Congratulations!

Thank you for acquiring a WENCIA watch!Swiss WENCIA watches are crafted in sterling silver, and designed in line with the latest fashion trends.

The history of the brand began in 1937 in Switzer-land, when the founder of the family manufacture, Mr. Oscar Wenger, registered the trademark WENCIA. Since then, for more than 70 years, the brand solely be-longs to the family Wenger.

WENCIA Jewelry Watches are handmade, conceived in the tradition of Swiss Haute Horlogerie. Wencia manufacture always pay great attention to details in the finishing and craftmanship of their watches.

To keep your watch functionning flawlessly for many years, we advise you to follow the recommendations in this manual.

ABOUT US

The watch shows the time using hours, minutes and seconds hands.

Time accuracy +/-20 seconds per month under normal conditions.

Battery life time up to 2 years.

All WENCIA quartz watches are equipped with Ronda Swiss movements. Ronda is one of the leading Swiss Quartz movements manufacturers.

1. Watch

2. User's Manual / Warranty Card

3. Silver watch polishing cloth

4. Packaging

SPECIFICATIONS SUPPLIED SET

6 7

WENCIA quartz watches benefit from the incomparable precision of quartz. Their power reserve usually enables them to operate for more than 2 years in continuous use. All you have to do is to set the time, and occasionally also the date if your watch is equipped with a display of this kind (please refer to the section of «Settings»).

E.O.L. (End of Life) function

Once it has been used up, the battery should be replaced without delay. If the seconds hand jumps every 4 seconds, this indicates that the battery has reached the end of its useful life and should be replaced in the very near future.

WENCIA jewelry watches should be worn and used with care. We would advise you to clean your watch regularly (except for the leather strap) using WENCIA silver polishing cloth. Do not leave it anywhere where it might be subjected to major variations in temperature or humidity, in direct sunlight or near strong magnetic fields. After immersion in water, it is highly recom-mended to bring your watch to authorized WENCIA dealer for control. If you plan not to wear your watch for several weeks or months, we would advise you to pull out the crown. This will stop the watch. Doing so, it will substantially reduce power consumption of your Renata Swiss battery.

USEFUL INFORMATION CARE & MAINTENANCE

We recommend that you contact an approved WENCIA representative or dealer, as they are equipped with the tools required to carry out the work and the necessary checks in a professional manner. A worn-out battery should be replaced immediately in order to reduce the risk of leakage and consequent damage to the movement.

Types of batteries used in WENCIA watches:

Renata 362, 364, 373, 384, 395

Temperature

Do not expose your watch to sudden changes in temperature, or expose to extreme heat or cool (above 60 °C or below 0 °C).

Magnetic fields

Do not expose your watch to strong magnetic field, for example, do not leave the watch near the Hi-fi speakers, mobile phones, computers, refrigerators and other appliances that generate electromagnetic fields.

REPLACING THE BATTERY PRECAUTIONARY MEASURES

8 9

Shocks

Protect your watch from shocks, including thermal: they could damage watch movement.

Aggressive substances

Avoid direct contact with solvents, detergents, perfumes, cosmetics, etc., they may damage the bracelet, the case or watch gaskets.

Maintenance

Regularly clean the case with silver polishing cloth, which is included in supplied set. This will prevent the occurrence of corrosion caused by contact with human sweat. WENCIA Jewelry Watches should not be immersed in water, including seawater. If immersed in water, please bring your WENCIA watch to an approved WENCIA representative or dealer (please refer to the section “Warranty”).

PRECAUTIONARY MEASURES DESCRIPTION OF THE DISPLAY AND CONTROL BUTTONS

Minute hand

Hour hand

Seconds hand

Date*

Day*

Screwed crown

FOR ANALOG WATCHES

* According to model

10 11

I III IIIII

Date* and Day* Setting

Pull the crown out to position II, as shown in the illustration, and turn it clockwise until the correct date is displayed, counterclockwise until the correct day is displayed. During this operation, your watch will continue to function normally, so you will not need to alter the time.

SETTINGS FOR ANALOG WATCHES

Current time setting

Pull the crown out to position III, as shown in the illustration, and – by turning it clockwise or counterclockwise – set the desired time.

On some models with a second hand, you can synchronize it with an official time signal. When the crown is pulled out to position III, the second hand stops. As soon as the time signal strikes, push the crown back down into position I.

* According to model

SETTINGS FOR ANALOG WATCHES

12 13

DESCRIPTION OF THE DISPLAY AND CONTROL BUTTONS

Centre stop-second

Minutehand

Hour hand

Minutecounter

Hour counter

Minute counter

Hour counter

Date*Day*

Crown

Push button B

Push button A

Second hand

Push-button A

Push-button B

FOR CHRONOGRAPH WATCHES

* According to model

CHRONOGRAPH: BASIC FUNCTION (Start / Stop / Reset)

Example: Start: press push-button A. Stop: to stop the timing, press pushbuttonA once more and read the threechronograph hands: 1h / 20min / 10 sec.

Zero positioning:Press push-button B.(The three chronograph hands will be resetto their zero positions).

14 15

Example:

Start: (start timing). Stop: (e.g. 15 min 5 sec following ).

Restart: (timing is resumed). *Stop: (e.g. 13 min 5 sec following ).

= 28 min 10 sec (The accumulated measured time is shown)

Reset: the three chronograph handsare returned to their zero positions.

Please note:* Following , the accumulation of thetiming can be continued by pressing push-button A.(Restart / Stop, Restart / Stop, …).

ACCUMULATED TIMING CHRONOGRAPH INTERMEDIATE OR INTERVAL TIMING CHRONOGRAPH

Example: Start: (start timing). Display interval: e.g. 10 minutes 10 seconds (timing continues in the background). *Making up the measured time:(the 3 chronograph hands are quicklyadvanced to the ongoing measured time). Stop: (final time is displayed). Reset: the 3 chronograph hands are returned to their zero position.

Please note:* Following , further intervals or intermediatescan be displayed by pressing push-button B.(display interval / make up measured time, ...).

Minute counter

Hour counter

Minute counter

Hour counter

Push-button A

Push-button A

Push-button B

Push-button BPush-button B

16 17

Push-button A

Push-button B

Centerstop-second

Example:

One or several chronograph hands are not intheir correct zero positions and have to beadjusted (e.g. following a battery change).

Pull out the crown to position III (all 3 chronograph hands are in their correct orincorrect zero position). Keep push-buttons A and B depressedsimultaneously for at least 2 seconds(the centre stop-second rotates by 360° corrective mode is activated).

ADJUSTING THE CHRONOGRAPH HANDS TO ZERO POSITION ADJUSTING THE CHRONOGRAPH HANDS TO ZERO POSITION

Adjusting the centre stop second: Single step A – 1 x short.Continuous A – long.Adjusting the next hand B.

Adjusting the hour counter hand (position 6h):Single step A – 1 x short.Continuous A – long.Adjusting the next hand B.

Adjusting the minute counter hand (position 9h):Single step A – 1 x short.Continuous A – long. Returning the crown to position I.Termination of the chronograph hands adjustment (can be carried out at any time).

А

А

А

B

B

Minute counter

Hour counter

18 19

Pull out the crown to position II (the watch continues to run). Turn the crown until the correct date 1 appears. Push the crown back into position I.

Please note:During the date changing phase between9 PM and 12 PM; the date must be set to the date of the following day.

SETTING THE TIME CHRONOGRAPH SETTING THE DATE (QUICK MODE) CHRONOGRAPH

Second hand *Pull out the crown to position III (the watch stops). Turn the crown until you reach the correct time: 8:45. *Push the crown back into position I.

Please note:

* In order to set the time to the exact second, must be pulled out when the second handis in position «60» (I).Once the hour and minute hands have beenset, must be pushed back into position I atthe exact second.

20 21

SETTING THE DATE/TIME FOLLOWING A BATTERY CHANGE SETTING THE DATE/TIME FOLLOWING A BATTERY CHANGE

Crown

*Date*Day

Second hand

* According to model

* Pull out the crown to position III (the watch stops). Turn the crown until the correct date 4 appears. ** Continue to turn the crown until the correct time 8:30 PM appears. Push the crown back into position I.

Please note:

* To set your watch to the exact second, please referto the chapter entitled "Setting the time".** Please observe the AM/PM clock rhythm.

Example:

– Date / time on the watch: 17 /1:25 АМ– Present date / time: 4 / 8:30 РМ

Pull out the crown to position II (the watch continues to run). Turn the crown until yesterday’s dateappears 3 .

22 23

• The life of the battery, strap, bracelet, clasp;

• Normal wear and tear and aging (e.g. scratched crystal; alteration of the color and/or material of non metallic straps and chains, such as leather, textile, rubber; peeling of the plating);

• Any damage on any part of the watch resulting from abnormal / abusive use, lack of care, negligence, accidents (knocks, dents, crushing, broken crystal, etc.), incorrect use of the watch and non-observance of the user’s manual directions;

• Any damage caused by exposure to water in the absence of appropriate markings on

them (water resistance);

• Any damage caused by corrosive chemicals or solvents;

• The WENCIA watch handled by non-authorized persons (e.g. for battery replacement, services or repairs) or which has been altered in its original condition beyond WENCIA LUXURY GROUP S.A.’s control.

Any further claim against WENCIA LUXURY GROUP S.A. e.g. for damages additional to the above described warranty is expressly excluded, except mandatory statutory rights the purchaser may have against the manufacturer.

THIS MANUFACTURER’S WARRANTY DOES NOT COVER:

Your WENCIA watch benefits from a twelve (12) months warranty, from the date of purchase under the terms and conditions of this warranty. The international WENCIA warranty covers material and manufacturing defects existing at the time of delivery of the purchased WENCIA watch (“defects”).

The warranty only comes into force if the warranty certificate is dated, fully and correctly completed and stamped by an official WENCIA dealer (“valid warranty certificate”).

During the warranty period and by presenting the valid warranty certificate, you will have the right to have any defect repaired free of charge.

In the event that repairs are improper to restore the normal conditions of use of your WENCIA watch, WENCIA LUXURY GROUP S.A. guarantees its replacement by a WENCIA watch of identical or similar characteristics. The warranty for the replacement watch ends twelve (12) months after the date of purchase of the replaced watch.

WARRANTY

24 25

The present warranty is only valid for the product to which it is registered for.

Ticket with unfilled or filled with illegible graphs specifications of products, with corrections in graphs or without customer signature is considered invalid.

In case of claims concerning causes of defects on the watch, it is mandatory that you obtain the report of an independent expert service center.

WARRANTY CARD

Model

Serial number

Purchase date

Is independent of any warranty that may be provided by the seller, for which he carries sole responsibility.

Does not affect the purchaser’s rights against the seller no any other mandatory statutory rights the purchaser may have against the seller.

THE ABOVE MANUFACTURER’S WARRANTY:

26 27

DATE OF ADMISSION

RETURN DATE MASTERREPAIR / DESCRIPTION

WARRANTY CARD

Product has been tested thoroughly. The product does not have any damage. Read and agreed with instructions and rules of operation.

Customer's signature

WARRANTY CARD

Dealer / Seller

Dealer Phone

Dealer Address

Seller's RepresentativeSignature

28 29

WARRANTY TICKET

Dealer / Seller

Model

Purchase date

Repair / Description

Spare parts

Repair cost

Repair date

ADDRESS OF SERVICE CENTER

30 31

ADDRESS OF SERVICE CENTER WARRANTY TICKET

Dealer / Seller

Model

Purchase date

Repair / Description

Spare parts

Repair cost

Repair date

32 33

WARRANTY TICKETADDRESS OF SERVICE CENTER

Dealer / Seller

Model

Purchase date

Repair / Description

Spare parts

Repair cost

Repair date

34

ADDRESS OF SERVICE CENTER