Downstream Equipment

Distribution

Section

Internal Construction

(Example)

From Utility

Company

(ConEd,

PSE&G, etc)

Service

Section

Custom Crown/

Pull Boxes

CT Cabinet

Please visit our Pull

Box and Enclosures

section

(Meter Bank)

‘Multi-Family Metering’

Pull Thru Wireway (Trough)

Powder coated . Also

available in Type 304 or

316 Stainless Steel

PanelBoards

“Where technical minds provide innovative solutions”

Service

Entrance

Internal Construction

(Example)Service End Box

The interior includes

‘overcurrent protection devices’(breakers), bus bars and insulated neutral bus bars. A lighting panel interior is mounted inside the can (back box) using 4 mounting studs.

Panelboards are available in

different sizes(P1-P5), power ratings (Amp),

internal construction. Here we use Lighting Panel (P1) as an example…

Residential circuit breakers are typically1-pole, 2-pole, or 4-pole breakers with current ratings of 225 amps or less and voltage ratings of 120 volts, 120/240 volts, or 240 volts

SWITCHBOARDThere are multiple elements that make up a switchboard. Included in the list of

elements are a frame, buses, overcurrent protection devices(Breakers, Switches), service metering, and outer covers.

Bus (busbar) Phase ArrangementBus bars (made out of copper) are required to have phases in sequence so an installer will find the same fixed-phase arrangement in each termination point in any switchboard. This requirement is established by NEMA (National Electrical Manufacturers Association).

Disconnect switches

CTCabinet

Pull BoxSeveral options are available to bring power into the switchboard service section, cable, pull box and bus duct. We will look at each one individually.

Bus Duct Entrance

Pull BoxAdded

Cable and Conduit

Elbows enable turns and height changes in the busway system. An elbow can turn the busway system right or left, up or down. Elbows are supplied with a joint stack and covers. Elbows may be ordered as stacks or sections. Elbow stacks are joint stacks that are angled

"edgewise" (for up/down changes) or "flatwise" (for left/right changes).

Busway AdvantageIn electrical power distribution, a bus duct (also called busway), is a sheet metal duct containing either copper or aluminum busbars for the purpose of conducting a substantial current of electricity. The three main

ways that a busway system will save you up front money over conduit and cable are: 1) Material Costs, 2)Shipping Costs, 3)Labor Costs

Busway is defined by the National Electrical Manufacturers Association (NEMA) as:

...a prefabricated electrical

distribution system consisting of bus bars in a protective enclosure, including straight lengths, fittings, devices, and accessories.

Busway includes bus bars, an insulating and/or support material, and a sheet metal housing.

Each watt-hour meter requires a meter socket to safely and securely connect it to the electrical service. Because meter designs and utility requirements vary, Apelio offers a variety of single-position and multiple-position meter sockets.

An insulating block secures the lugs, jaws, and bussing to the enclosure.

Current PathWhen in operation, electrical current flows from the service (line-side) conductors through the meter to the load-side conductors and then to the load center or panelboard for distribution to branch loads

Metering System

Trough is designed to protect wiring against

rain, sleet and snow in outdoor installations, or indoors against dripping water.

Fabricated in accordance with ULspecifications from 16-14 gauge Galvanized Powder coated Steel, Aluminum or SS304/ SS316. Continuously welded body, gasketed rainproof Cover with heavy duty butt hinges and quick release clamps.

Telescope FittingAdjustable Telescopic Fitting makes it easy to adjust the length of final connection and save the hassle of precise measuring

TROUGH Wireway

90° Sweep Elbow and

Sweep Tee designed for

large radius turns. Used with

vertical or horizontal

Trough sections. Removable

top and inside covers.

Custom dimensioning to customer specifications, our boxes are made with superior welding that helps prevent box deformation when pulling cables or punching multiple holes in them.

Pull Boxes/ Crown BoxesApelio's ability to manufacture high end Pull Boxes is not limited to custom boxes. We carry a large array of standard Pull Boxes ranging from the smallest to the largest sizes, painted to withstand rust and made from quality materials.

Complex Design with dividing capabilities will allow customer to use the same box in different applications

Our Pull Boxes made of rigid body acuminated by superior welding and materials to withstand harsh environments. Apelio offers wide range of material thickness and type to satisfy every need.• Bodies and doors fabricated from 16,14, or 12 gauge carbon steel and

pre-Galvanized or Galvannealed steel• Removable Covers• Sectional Dismantle• Powder coating availability• SwitchBoard Hole Lineup

APELIO offers a wide range of electrical enclosures ideal for a variety of indoor or outdoor applications.

NEMA 4X enclosures are primarily intended for outdoor use and offer a superior level of protection from corrosion and extreme environments. APELIO produces these enclosures in 5052-H32 aluminum, 304 or 316 Stainless Steel and they are available in a number of styles for your demanding applications. Our adherence to the rigorous NEMA standards will give you a quality enclosure, delivered quickly at a competitive price.

APELIO produces NEMA 1 electrical enclosures for general purpose indoor use. We adhere to NEMA standards to provide you a quality enclosure for most basic applications. NEMA 1 enclosures are intended for use fundamental applications, or where extreme environmental conditions do not exist

Pull Boxes, Enclosures

NEMA 3R enclosures are compatible for both indoor or outdoor applications, and holds the least demanding rating for outdoor use. Mostly made for lighting contractors, housing power distribution, switch gear, and other electrical components that need to be protected in an outdoor environment.

The National Electrical Manufacturer Association (NEMA) uses a standard rating system that defines the types of environments in which an electrical enclosure can be used, and frequently signifies a fixed enclosure's ability to withstand certain environmental conditions.

We manufacture All NEMA rated enclosures.Per customer request most of them can be made our of either Powder coated Galvanized steel, Aluminum or Stainless Steel type 304 or 316. Here we explain a few the most popular NEMA types…..

NEMA 12 enclosures are intended mainly for indoor industrial, manufacturing, and machining applications. These metal enclosures will protect against dust, dirt, and dripping non-corrosive liquids, oil and lubricants