Upload
others
View
17
Download
0
Embed Size (px)
Citation preview
Position the VESA mount bracket over the four VESA mount points and fasten the bracket to the chassis.
12. Attach VESA mount bracket
Slot the HDD into the mounting bracket. Secure the HDD with mounting bracket to the chassis by fastening the screws on either side.
Fasten the rear cover in place by securing the nine retention screws and two screws beneath the ODD drive.
Fasten the ODD carrier to the chassis by securing the retention screw on either side of the carrier.
7. Securing the HDD to the Chassis 8. Securing the ODD to the Chassis 9. Replacing the Rear Cover
With the chassis placed face-down on a flat surface, unfasten the nine screws on the rear cover.
Once all screws have been removed, lift the cover from the bottom.
1. Unfastening the Rear Cover Screws
Remove the ODD cover and unfasten the two screws inside. It is important to remove these prior to removing the rear cover.
2. Unfastening the Screws behind the ODD Cover 3. Lifting the Rear Cover
Connect the camera and webcam to single USB headers if present on the board.
Connect the panel off switch (if present).Connect the system fan.
4. Connecting the Camera and Webcam 5. Connecting the System Fan 6. Connecting the Panel Off Switch
WIBTEK A23 ALL-IN-ONE PC CHASSIS INTEGRATION WITH THE GIGABYTE GA-Q87TN DESKTOP BOARD
Loosen the centre fastener and four surrounding fasteners to prepare the stand for removal.
Press the hinge cover plate as sown to free the retention brackets and remove the cover and stand. Please Note: If the stand does not separate easily, ensure that all relevant fasteners have been removed. Do not use excessive force as this may damage the stand and rear cover.
10. Preparing for Pedestal Stand Removal 11. Removing the Pedestal Stand
LCD INTEGRATION NOTES
GENERAL INTEGRATION NOTES
GIGABYTE GA-Q87TN DESKTOP BOARD OVERVIEW
1. Inserting the LVDS Connector 2. Checking Jumper Settings
1. Placing the Thermal Retention Mechanism 2. Placing the Thermal Tab 3. Inserting the Desktop Board
4. SATA and DATA 5. Single USB Connection 6. Wireless Connection
1
2
When inserting the LVDS Connector, confirm correct alignment. Once in, never remove the cable by “pulling on the wires”, as this could permanently damage the cable.
Confirm that this jumper settings for the Backlight Inverter and Front Panel voltage are correct for the inverter and the board being integrated.
Check that the thermal retention mechanism is in place before installing the desktop board.
Once the thermal retention mechanism is in place, secure the thermal pad as above.
When installing the desktop board, it may help to locate the power connection on the desktop board with the IO shield first and then “swivel” the board in. Check that the ports on the desktop board connect with the IO shield contacts.
The SATA power cable provides power for the HDD and ODD. Where a “single” USB connection is connected to a dual USB header, confirm that the “red” cable is aligned to the pins closest to PIN 1 (white marking at the base). It is possible to connect two single USB connections to a dual port USB header in this manner.
For Wireless-N & Wireless-AC maximum bandwidth potential, ensure that both wireless antennae are connected to the wireless adapter.
FPD - 19V
1 2 3
LCD - 5V
1 2 3
3. Configuring the BIOS
Ensure LVDS Cable is ConnectedNavigate to ChipsetSelect Enable for LVDS Control FunctionSelect M215HGE-L10/M240Q002 for Panel Type
Navigate to Chipset
Select Enable for LVDS Control Function
Select M215HGE-L10/M240Q002 for Panel Type
5 6
7
77
7
8
9 10
11
12 13 13 14 15 17 17 19 2021
22
23 24
2526
27282930
3132
33
1816
43
21
1. LVDS
2. LCD Panel SW
3. Front Panel
4. CPU Fan
5. SATA Power
6. DDR3 SP DIMM
7. SATA III Ports
8. Single USB Header
9. USB 3 Connect
10. Half Length Mini PCI-e Slot
11. Internal ATX 19V Connector
12. 19V DC In
13. 2x GbE LAN Ports
14. Display Port
15. HDMI
16. COM1
17. USB 3
18. LPT
19. Speaker Out
20. Mic In
21. Speaker
22. FP Audio
23. DMIC
24. CLR CMOS
25. Full Length Mini PCI-e / mSATA
26. PCI-e 4X
27. 2 x Single USB Headers
28. Dual USB 2 Header
29. FPD
30. BL_SW
31. WFLED
32. LCD PWR
33. FPD PWR