Upload
dinhhanh
View
218
Download
0
Embed Size (px)
Citation preview
2-347-711-31(1)
2003 Sony Corporation
Operating InstructionsBefore operating the unit, please read this manual thoroughly andretain it for future reference.
UWP-C1/C2UWP-S1/S2UWP-X1/X2
WirelessMicrophone Package
2
3
Table of Contents
Configuration of thePackages ............................. 4UWP-C1 ..................................... 4UWP-C2 ..................................... 5UWP-S1 ..................................... 6UWP-S2 ..................................... 7UWP-X1 .................................... 8UWP-X2 .................................... 9
Features .................................. 10Precautions............................. 12Parts Identification ................. 13
Body-pack transmitter(UTX-B1) ................................. 13Hand-held microphone(UTX-H1) ................................ 14Portable diversity tuner(URX-P1) ................................. 15Half-rack size diversity tuner(URX-R1) ................................ 17Diversity tuner module(URX-M1) ............................... 18
Power Supply ......................... 20Inserting the batteries ............... 20
Attachment and InstallationProcedures ........................ 23Attaching the suppliedaccessories to the body-packtransmitter (UTX-B1) .............. 23Attaching the suppliedaccessory to the hand-heldmicrophone (UTX-H1) ............ 24Attaching the suppliedaccessories to the portablediversity tuner (URX-P1) ......... 24Installing the diversity tunermodule (URX-M1) .................. 25
Settings ................................... 28Setting the transmissionchannel ..................................... 28Setting the reception channel ... 29Setting the attenuation levelof the audio input ..................... 30Resetting the accumulatedbattery use time indication ....... 31Setting the RF output level ...... 32Setting the monitor level(portable diversity tuner(URX-P1) only) ....................... 32
Operation ................................ 33System Configurations .......... 34Error Messages ...................... 37Troubleshooting ..................... 38Specifications ......................... 40Appendix ................................. 44
Wireless microphone systemfrequency list ............................ 44AC adapter for use with theURX-R1 ................................... 46
Configuration of the Packages
4
Configuration of the Packages
This operation manual is for the UWP-C1/C2/S1/S2/X1/X2wireless microphone packages. The contents of each packageare described below.
UWP-C1
The UWP-C1 consists of a body-pack transmitter (UTX-B1)and a portable diversity tuner (URX-P1). When used inconjunction with a compact camcorder, the UWP-C1 makes amobile system for ENG (Electronic News Gathering) or EFP(Electronic Field Production) purposes.
Body-pack transmitter(UTX-B1) (1)
Portable diversity tuner(URX-P1) (1)
Supplied accessories• Omni-directional lavalier microphone
(1)• Wind screen (1)
• XLR-BMP conversion cable (for usewith the URX-P1 only) (1)
• Holder clip (1)
• Shoe mount adapter (1) • Belt clip (2)
• Microphone stand adapter (1) • Operation manual (1)
5
UWP-C2
The UWP-C2 consists of a hand-held microphone (UTX-H1)and a portable diversity tuner (URX-P1). When used inconjunction with a compact camcorder, the UWP-C2 makes amobile system for ENG (Electronic News Gathering) or EFP(Electronic Field Production) purposes.
Hand-held microphone(UTX-H1) (1)
Portable diversity tuner(URX-P1) (1)
Supplied accessories
• Microphone holder (1) • Belt clip (1)
• Shoe mount adapter (1) • XLR-BMP conversion cable (for usewith the URX-P1 only) (1)
• Microphone stand adapter (1) • Operation manual (1)
Configuration of the Packages
6
UWP-S1
The UWP-S1 consists of a body-pack transmitter (UTX-B1)and a half-rack size diversity tuner (URX-R1). The UWP-S1 issuitable for constructing a wireless system for AVpresentations.
Body-pack transmitter(UTX-B1) (1)
Half-rack size diversity tuner(URX-R1) (1)
Supplied accessories
• Unidirectional lavaliermicrophone (1)
• Wind screen (1) • Holder clip (1)
• AC adapter (1) (Seepage 46.)
• Belt clip (1) • Operation manual (1)
7
UWP-S2
The UWP-S2 consists of a hand-held microphone (UTX-H1)and a half-rack size diversity tuner (URX-R1). The UWP-S2 issuitable for constructing a wireless system for AVpresentations.
Hand-held microphone(UTX-H1) (1)
Half-rack size diversity tuner(URX-R1) (1)
Supplied accessories
• Microphone holder (1) • AC adapter (1) (See page 46.)
• Operation manual (1)
Configuration of the Packages
8
UWP-X1
The UWP-X1 consists of a body-pack transmitter (UTX-B1)and a diversity tuner module (URX-M1). By installing the tunermodule into a tuner base unit or a powered mixer, the systemconstruction to meet the desired purpose of use and requiredsystem scale becomes possible.
Body-pack transmitter(UTX-B1) (1)
Diversity tuner module(URX-M1) (1)
Supplied accessories
• Unidirectional lavaliermicrophone (1)
• Wind screen (1) • Holder clip (1)
• Belt clip (1) • Operation manual (1)
9
UWP-X2
The UWP-X2 consists of a hand-held microphone (UTX-H1)and a diversity tuner module (URX-M1) . By installing thetuner module into a tuner base unit or a powered mixer, thesystem construction to meet the desired purpose of use andrequired system scale becomes possible.
Hand-held microphone(UTX-H1) (1)
Diversity tuner module(URX-M1) (1)
Supplied accessories
• Microphone holder (1) • Operation manual (1)
Features
10
Features
Each of the UWP-C1/C2/S1/S2/X1/X2 wireless microphone packages(referred to as the UWP serieshereafter) combines a transmitter(body-pack transmitter (UTX-B1) orhand-held microphone (UTX-H1)) anda receiver (portable diversity tuner(URX-P1), half-rack size diversitytuner (URX-R1), or diversity tunermodule (URX-M1)). The UWP seriescan be used with a compact camcorderfor ENG (Electronic News Gathering)purposes, and with a powered mixerfor AV presentations or as a PA(public address) system.
Note
The UWP series is not compatiblewith conventional WRT seriestransmitters, WRR series tuners, orWRU series tuner units.
The features of each package aredescribed below.
UWP-C1
Body-pack transmitter (UTX-B1)This is a small and lightweighttransmitter with a crystal-controlledPLL (phase lock loop) synthesizedsystem and a BMP-type microphoneinput connector. The RF power outputcan be set at 10 mW or at 2 mW.
Portable diversity tuner(URX-P1)This tuner employs a space diversitysystem with little signal dropout andtwo angle-adjustable antennas. Itcomes with an adapter for mountingthe tuner on the compact camcorder(DSR-PDX10/PDX10P/PD150/PD150P, etc.).
UWP-C2
Hand-held microphone (UTX-H1)This microphone is equipped with abuilt-in antenna and a unidirectionaldynamic microphone unit. The RFpower output can be set at 10 mW orat 2 mW.
Portable diversity tuner(URX-P1)This tuner employs a space diversitysystem with little signal dropout andtwo angle-adjustable antennas. Itcomes with an adapter for mountingthe tuner on the compact camcorder(DSR-PDX10/PDX10P/PD150/PD150P, etc.).
UWP-S1
Body-pack transmitter (UTX-B1)This is a small and lightweighttransmitter with a crystal-controlledPLL (phase lock loop) synthesizedsystem and a BMP-type microphoneinput connector. The RF power outputcan be set at 10 mW or at 2 mW.
11
Half-rack size diversity tuner(URX-R1)This tuner employs a space diversitysystem with little signal dropout andtwo angle-adjustable antennas. Itcomes with two types of audioconnectors (1/4-inch jack and XLRtype) on the rear panel.
UWP-S2
Hand-held microphone (UTX-H1)This microphone is equipped with abuilt-in antenna and a unidirectionaldynamic microphone unit. The RFpower output can be set at 10 mW orat 2 mW.
Half-rack size diversity tuner(URX-R1)This tuner employs a space diversitysystem with little signal dropout andtwo angle-adjustable antennas. Itcomes with two types of audioconnectors (1/4-inch jack and XLRtype) on the rear panel.
UWP-X1
Body-pack transmitter (UTX-B1)This is a small and lightweighttransmitter with a crystal-controlledPLL (phase lock loop) synthesizedsystem and a BMP-type microphoneinput connector. The RF power outputcan be set at 10 mW or at 2 mW.
Diversity tuner module(URX-M1)This tuner module can be incorporatedinto the MB-806A Tuner Base Unit orSRP-X700P Powered Mixer.
UWP-X2
Hand-held microphone (UTX-H1)This microphone is equipped with abuilt-in antenna and a unidirectionaldynamic microphone unit. The RFpower output can be set at 10 mW orat 2 mW.
Diversity tuner module(URX-M1)This tuner module can be incorporatedinto the MB-806A Tuner Base Unit orSRP-X700P Powered Mixer.
Precautions
12
Precautions
• The UWP series product must beused within a temperature range of0°C to 40°C (32°F to 104°F).
• Operating the UWP series productnear electrical equipment (motors,transformers, or dimmers) may causeit to be affected by electromagneticinduction. Keep the UWP seriesproduct as far from such equipmentas possible.
• The presence of the lightingequipment may produce electricalinterference over the entirefrequency range. Position the UWPseries product so that interference isminimized.
• To avoid degradation of the signal-to-noise ratio, do not use the UWPseries product in noisy places or inlocations subject to vibration, such asthe following:— near electrical equipment, such as
motors, transformers or dimmers— near air conditioning equipment
or places subject to direct airflow from an air conditioner
— near public address loudspeakers— where adjacent equipment might
knock against the tunerKeep the UWP series product as farfrom such equipment as possible oruse buffering material.
• Clean the surface and the connectorsof the UWP series product with adry, soft cloth. Never use thinner,benzene, alcohol or any otherchemicals, since these may mar thefinish.
To prevent electromagneticinterference from portablecommunication devicesThe use of portable telephones andother communication devices nearthe UWP series product may resultin malfunction and interference withaudio signals. It is recommendedthat portable communicationdevices near the UWP seriesproduct be turned off.
13
Transmissionchannel
Transmissionfrequency
Attenuationlevel of theinput signal
Accumulatedbattery usetime
PresstheSETbutton.
Parts Identification
Body-pack transmitter(UTX-B1)
1 Antenna
2 Audio input connectorConnect the supplied lavaliermicrophone here.
3 Power indicatorLights up red when the transmitter istuned on.
4 Display section
A AF (audio frequency) indicationAppears whenever the input audiosignal is stronger than the referencelevel.
B RF (antenna output) indicationAppears during signal transmissionfrom the antenna.
C RF (antenna output) levelindicationShows the RF output level setting.For details, see “Setting the RF outputlevel” on page 32.
D BATT (battery) indicationShows the battery condition.For details, see “Power Supply” onpage 20.
E CH (channel) indicationShows the transmission channel. Eachtime you press the SET button intransmission mode, the channelindication changes as follows.For details, see “Settings” on page28.
A B D
E
AF RF
CH
BATT
C
HL
Parts Identification
14
5 + (+ selection) / – (– selection/reset) buttonsPress these buttons to set thetransmission channel, frequency, orattenuation level of the input signal.The “–” button resets the accumulatedbattery use time to “00:00”.
6 Battery compartmentAccommodates two LR6 (size AA)alkaline batteries.For details on how to insert thebatteries, see “Power Supply” onpage 20.
7 SET buttonPress to change and enter displayparameters.For details, see “Settings” on page28.
8 POWER switchTurns the power of the transmitter ONor OFF.
Hand-held microphone(UTX-H1)
1 Power indicatorLights up red when the microphone isturned on.
2 POWER switchTurns the power of the microphoneON or OFF.
3 Battery compartmentAccommodates two LR6 (size AA)alkaline batteries.For details on how to insert thebatteries, see “Power Supply” onpage 20.
4 Display section
A AF (audio frequency) indicationAppears whenever the input audiosignal is stronger than the referencelevel.
B RF (antenna output) indicationAppears during signal transmissionfrom the antenna.
C RF (antenna output) levelindicationShows the RF output level setting.For details, see “Setting the RF outputlevel” on page 32.
A B D
E
C
HL
The rearside of thebatterycompartment
15
D BATT (battery) indicationShows the battery condition.For details, see “Power Supply” onpage 20.
E CH (channel) indicationShows the transmission channel. Eachtime you press the SET button, thechannel indication changes as follows.For details, see “Settings” on page28.
5 + (+ selection) / – (– selection/reset) buttonsPress these buttons to set thetransmission channel, frequency, orattenuation level of the input signal.The “–” button resets the accumulatedbattery use time to “00:00”.
6 SET buttonPress to change display parameters.For details, see “Settings” on page28.
Transmissionchannel
Transmissionfrequency
Attenuationlevel of theinput signal
Accumulatedbattery usetime
PresstheSETbutton.
Portable diversity tuner(URX-P1)
1 Antennas a/bThe angle of the antennas can beadjusted manually.
2 MONITOR connector (3.5-mmdiameter stereo mini jack)To monitor the tuner output, connectthe headphones to this connector.
3 RF (radio frequency) indicatorIndicates the strength of the RF inputsignal.
On in green: RF input is 15 dBµ*or more.
Off: RF input is less than 15 dBµ*.
......................................................................................................................................................................
* 0 dBµ = 1 µVEMF
Parts Identification
16
4 Display section
A RF (radio frequency) indicationsThe number of dots indicates the RFinput level.
B AF (audio frequency) indicationAppears whenever the output audiosignal is stronger than the referencelevel.
C BATT (battery) indicationShows the battery condition.For details, see “Power Supply” onpage 20.
D GP (group)/CH (channel)indicationShows the reception channel groupand channel number. Each time youpress the SET button, the channelindication changes as follows.For details, see “Settings” on page 28.
5 + (+ selection) / – (– selection/reset) buttonsPress these buttons to set the receptionchannel and frequency. The “–”button resets the accumulated batteryuse time to “00:00”. These buttons canalso be used to adjust the monitorlevel.
6 Battery compartmentAccommodates two LR6 (size AA)alkaline batteries.For details on how to insert thebatteries, see “Power Supply” onpage 20.
7 SET buttonPress to change display parameters.For details, see “Settings” on page28.
8 POWER switchTurns the power of the tuner ON orOFF.
9 OUTPUT (audio output)connector (3.5-mm diameter stereomini jack)Connect one end of the supplied XLR-BMP conversion cable here and theother end to the microphone input on acamcorder, mixer, or amplifier. If themicrophone input connector on thedevice connected to the tuner is astereo mini jack, use an optional miniplug y stereo mini plug conversioncable (RK-G139, etc.) and connect themini plug (2-pole) to the tuner andstereo mini plug (3-pole) to themicrophone input connector on thedevice.
AFRF BATT
CH
A B
D
C
Receptionchannelgroup andnumber
Receptionfrequency
Accumulatedbattery usetime
PresstheSETbutton.
17
Half-rack size diversitytuner (URX-R1)
1 POWER switchTurns the power of the tuner ON orOFF.
2 Antennas a/bThe angle of the antennas can beadjusted manually.
3 MONITOR connector (phonejack)To monitor the tuner output, connectthe headphones to this connector andadjust the monitor level with theMONITOR control. Use either stereoor monaural headphones.
4 MONITOR controlTurn to adjust the output monitoringlevel (through the headphones).
5 + (+ selection) / – (– selection/reset) buttonsPress these buttons to set thereception channel and frequency.
6 Display section
A RF (radio frequency) indicationsThe number of dots indicates the RFinput level.
B AF (audio frequency) indicationAppears whenever the output audiosignal is stronger than the referencelevel.
C GP (group)/CH (channel)indicationShows the reception channel groupand channel number. Each time youpress the SET button, the channelindication changes as follows.For details, see “Settings” on page28.
Front panel
Rear panel
AFRF
CH
A B
C
Parts Identification
18
7 RF (radio frequency) indicatorIndicates the strength of the RF inputsignal.
On in green: RF input is 25 dBµ*or more.
Off: RF input is less than 25 dBµ*.
8 SET buttonPress to change display parameters.For details, see “Settings” on page28.
9 TUNER OUTPUT (audiooutput) connector (XLR type)Connect to the audio input connectorof a mixer or amplifier, etc.
0 LEVEL (audio output level)switchSets the output level of the TUNEROUTPUT connector (XLR type) to–28 dBm or –58 dBm.Select the setting according to theinput level of the equipment connectedto the tuner.
qa TRS PHONE (tuner audiooutput) connector (1/4-inch jack)Connect to the audio input connectorof a mixer or amplifier, etc. Theoutput level from this connector is –30dBm.
qs DC IN 9V (DC power input)connectorConnect the supplied AC adapter here.
Diversity tuner module(URX-M1)
1 SET buttonPress to change display parameters.For details, see “Settings” on page28.
2 RF (radio frequency) indicatorIndicates the strength of the RF inputsignal.
On in green: RF input is 25 dBµ*or more.
Off: RF input is less than 25 dBµ*.
3 Display section
Receptionchannelgroup andnumber
Receptionfrequency
PresstheSETbutton.
AFRF
CH
A B
C
......................................................................................................................................................................
* 0 dBµ = 1 µVEMF
19
Receptionchannelgroup andnumber
Receptionfrequency
PresstheSETbutton.
A RF (radio frequency) indicationsThe number of dots indicates the RFinput level.
B AF (audio frequency) indicationAppears whenever the output audiosignal is stronger than the referencelevel.
C GP (group)/CH (channel)indicationShows the reception channel groupand channel number. Each time youpress the SET button, the channelindication changes as follows.For details, see “Settings” on page28.
4 + (+ selection) / – (– selection/reset) buttonsPress these buttons to set the receptionchannel and frequency.
Power Supply
20
Power Supply
This section explains the power supplyfor each component.
• Half-rack size diversity tuner(URX-R1)Connect the supplied AC adapter tothe DC IN 9V connector on the rearpanel, and then connect the ACadapter to a wall outlet.
• Diversity tuner module(URX-M1)When incorporated into anothercomponent (e.g., MB-806A, SRP-X700P, etc.), the tuner module drawsits power from that component.For details on the power supply tothe diversity tuner module, refer tothe operating instructions of thecomponent in which the diversitytuner module is installed.
• Body-pack transmitter (UTX-B1), hand-held microphone(UTX-H1), and portablediversity tuner (URX-P1)These components can be poweredby two LR6 (size AA) alkalinebatteries for about six hours ofcontinuous operation (at 25 ºC(77ºF)). Details on inserting thebatteries and the battery conditionindication are given below:
Inserting the batteries
Body-pack transmitter (UTX-B1)/portable diversity tuner(URX-P1)
The procedure below uses the body-pack transmitter (UTX-B1) in theillustrations. Batteries are, however,inserted in the portable diversity tuner(URX-P1) in the same manner.
1 Slide the latches on both sides ofthe transmitter/tuner at the sametime and open the batterycompartment.
2 Align two new LR6 (size AA)alkaline batteries with the polaritymarkings and insert them into thebattery compartment, and thenclose the cover.
Latch
21
Battery indication
When you turn the power on, the battery condition is shown by the BATTindication in the display section.
When the indication in column 4 starts to flash, replace the batteries with newones. Be sure to check the expiration date printed on the new batteries beforeusing them.
1 2 3 4
BATT indication Lights Lights Lights Flashes
Battery status Good Less than Less than Almost50% charged 20% charged drained
Hand-held microphone(UTX-H1)
1 Turn the grip in the direction ofthe arrow to open the batterycompartment.
2 Align two new LR6 (size AA)alkaline batteries with the polaritymarkings and insert them into thebattery compartment.
3 Turn the grip in the directionopposite to the arrow in step 1 toclose the battery compartment.
Note
If you open the battery compartmentduring signal transmission, the noisemay occur. Be sure to turn themicrophone off before opening thebattery compartment.
Power Supply
22
Note
The indicated battery condition maynot be correct if the batteries were notnew when installed. If you plan to usethe component for a long period, it isrecommended that you replace thebatteries with brand new ones.
Notes on batteries
Batteries may leak or explode ifmistreated. Be sure to follow theseinstructions.• Be sure to install the batteries with
the correct polarity.• Always replace the two batteries
together.• Do not use different types of
batteries or old and new onetogether.
• The batteries are not rechargeable.• When not using the component for a
long period of time, remove thebatteries to avoid leakage. If thebatteries do leak, clean all leakagefrom the battery compartment and thecomponent. Leakage left in thecompartment and the component maycause poor battery contact. If thereseems to be poor battery contact,consult your Sony dealer.
23
Attachment and InstallationProcedures
This section describes the proceduresfor attaching the supplied accessoriesto components and the installation ofthe diversity tuner module (URX-M1)into the MB-806A Tuner Base Unit orSRP-X700P Powered Mixer.
Attaching the suppliedaccessories to thebody-pack transmitter(UTX-B1)
Attaching the microphone
Attaching the holder clip tothe microphone
Attaching the wind screen tothe microphone
Attaching the belt clip
Microphone (supplied)
For a secure connection, be sure to turnand lock the connector cover.
Push the holder clip against thebottom of the microphone until theholder clip clicks into place.
Insert the microphone into the hole atthe bottom of the windscreen.
Insert one end of the belt clip into oneof two holes on either side of thetransmitter, and then insert the otherend into the hole on the other side.
Attachment and Installation Procedures
24
Removing the belt clipInsert a pointed object such as aballpoint pen between the belt clip andthe transmitter to make some spacebetween them, and then remove theend of the belt clip from the hole onthe side of the transmitter.
Attaching the suppliedaccessory to the hand-held microphone(UTX-H1)
Attaching the microphoneholder
Attaching the suppliedaccessories to theportable diversity tuner(URX-P1)
Connecting the XLR-BMPconversion cable to theOUTPUT connector
Note
The XLR-BMP conversion cable isfor use with the URX-P1 only.Attaching the cable to the audio inputconnector of the UTX-B1 may causedamage to the transmitter or thedevice connected to the transmitter.
Attaching the belt clip
See “Attaching the belt clip” on page23.
XLR-BMP conversion cable(supplied)
For a secure connection, be sure toturn and lock the connector cover.
Insert the bottom part of themicrophone into the holder.
25
Attaching the shoe mountadapter
Be sure tohold thehorizontalpart of thebelt clip withthehorizontalgroove onthe shoemountadapter.
After attaching the belt clip and theshoe mount adapter, insert themicrophone stand adapter into thescrew hole at the top of the shoemount adapter, and then rotate themicrophone stand adapter until it issecurely attached.
After attaching the belt clip, insert theshoe mount adapter between theportable diversity tuner (URX-P1) andthe belt clip, with the vertical parts of thebelt clip aligned with the two verticalparallel grooves on the shoe mountadapter. Then, push the shoe mountadapter in the direction of the arrow, andthen catch the horizontal part of the beltclip with the horizontal groove on theshoe mount adapter to hold the belt clipin place.
Attaching the microphonestand adapter
Installing the diversitytuner module (URX-M1)
Notes
• Before installing the diversity tunermodule (URX-M1), make sure theunit into which the diversity tunermodule (URX-M1) will be installedis turned off. Do not install oruninstall the diversity tuner module(URX-M1) while the unit is turnedon, as this may damage theconnector or cause noise.
Attachment and Installation Procedures
26
• The buttons and display on the frontpanel of the diversity tuner module(URX-M1) may be damaged if theyare gripped too strongly. Alwayshold the diversity tuner module bythe side.
• Do not put your fingers on theconnectors on the rear panel of thediversity tuner module (URX-M1) orinto the slot on the unit into whichthe diversity tuner module (URX-M1) will be installed.
• Keep the diversity tuner module(URX-M1) away from staticelectricity.
Installing a diversity tunermodule (URX-M1) into an MB-806A Tuner Base Unit
The MB-806A Tuner Base Unit canaccommodate up to 6 diversity tunermodules (URX-M1).
1 Holding both sides of the diversitytuner module (URX-M1), insert itinto the slot.Push it in until you hear a click.
2 To install two or more diversitytuner modules (URX-M1) , detachthe necessary number of blankpanels by pressing the top andbottom tabs on each panel towardseach other and pulling the panelout. Then do step 1 for eachmodule.
Removing a diversity tunermodule (URX-M1)On the bottom panel of the MB-806A,locate the lever corresponding to theslot of the diversity tuner module(URX-M1) to be removed and pull thelever forward. The diversity tunermodule (URX-M1) is ejected from theslot.
Lever
27
Installing a diversity tunermodule (URX-M1) into anSRP-X700P Powered Mixer
The SRP-X700P Powered Mixer canaccommodate up to 2 diversity tunermodules (URX-M1).
1 Remove the tuner slot cover fromthe SRP-X700P and inspect thetop and bottom sides of thediversity tuner module. Then,holding the tuner module on bothsides, insert it into the slot.
MASTER
SCENERECALL
GPAF
RF
GP CH
BATT
LINE 4 SELECTA
A
B
C
D
E
F
B
Removing the diversity tunermodule (URX-M1)Insert a screwdriver with a shaftdiameter of between 2 to 4 mm and ashaft length of 30 mm or longer intothe hole under the lower part of thetuner slot and remove the tunermodule.
Diversitytuner module(URX-M1)
Diversitytunermodule(URX-M1)
MASTER
SCENERECALL
GPGPAFAF
RFRF
GPGPCHCH
BATTBATT
LINE 4 SELECTA
A
B
C
D
E
F
B
Settings
28
Settings
4 When the desired channel number(or frequency) appears, set thePOWER switch to OFF tocomplete the setting, or press theSET button to set other items.The results are stored in memory.The stored channel number (orfrequency) will appear in thedisplay section the next time youturn on the transmitter by settingthe POWER switch to ON.
Notes
• When you are setting thetransmission channel, the transmittercannot be used to transmit signals.
• Do not remove the batteries whilesetting the transmission channel. Ifthey are inadvertently removed, re-insert them immediately and redo theprocedure “Setting the transmissionchannel” from step 1.
• Make sure that the selected channelis the same on the transmitter andtuner being used in the same system.
• If you turn off the transmitter andthen immediately turn it on rightafter setting the transmissionchannel, the unit may not operatenormally. Wait a few seconds beforeturning it on again.
Setting thetransmission channel
The procedure below is thesame for all UWP seriestransmitters (UTX-B1/H1).
See “Wireless microphone systemfrequency list” on page 44 for detailson the selectable channel groups andchannels.
1 Turn on the transmitter whilepressing down the SET button.Keep pressing the SET buttonuntil the display sectionparameters that were displayedwhen the unit was last turned offstart to flash.
2 Press the SET button repeatedlyuntil the channel number (orfrequency) indication appears.
3 Press the + or – button to selectthe channel number (orfrequency).Pressing the + button cycles theindication in the order shown inthe tables in “Wirelessmicrophone system frequencylist” on page 44.Pressing the – button cycles theindications in the oppositedirection.Hold down the + or – button tochange the channel number (orfrequency) faster.
29
Setting the receptionchannel
The procedure below is thesame for all UWP series tuners(URX-P1/R1/M1).
See “Wireless microphone systemfrequency list” on page 44 for detailson the selectable channel groups andchannels.
1 Press down the SET button formore than one second.Keep pressing the SET buttonuntil the display sectionparameters start to flash.
2 Press the SET button repeatedlyuntil the channel group and thechannel number indicationsappear.The channel group indicationstarts to flash.
3 Press the + or – button to selectthe channel group.Pressing the + button cycles theindication in the order shown inthe tables in “Wirelessmicrophone system frequencylist” on page 44.Pressing the – button cycles theindications in the oppositedirection.Hold down the + or – button tochange the channel group faster.
4 When the desired channel groupnumber appears, press the SETbutton.The selected group is entered.The right four digits start to flashto allow the selection of thechannel number.
5 Press the + or – button to selectthe channel number.The channel indication changes inthe order shown in the tables in“Wireless microphone systemfrequency list” on page 44.
7 When the desired channel numberappears, leave the tuner for about10 seconds until the selectedchannel number stops flashing andthe selection is stored in memory.
Example: When the channel group 00is selected
Settings
30
• If you turn off the tuner and thenimmediately turn it on right aftersetting the reception channel, the unitmay not operate normally. Wait afew seconds before turning it onagain.
Setting the attenuationlevel of the audio input
The procedure below is thesame for all UWP seriestransmitters (UTX-B1/H1).
The attenuation level can be set duringsignal transmission.
1 Do the following while thereis no signal transmission.Turn on the transmitter whilepressing down the SET button,and press the SET buttonrepeatedly until the attenuationlevel indication appears in thedisplay section.
Do the following while thereis signal transmission.Press the SET button repeatedlyuntil the attenuation levelindication appears in the displaysection.
2 Press the + or – button to selectthe attenuation level.The selectable range is from 0 dBto 21 dB in steps of 3 dB (thefactory setting is 0 dB).
To selct the channel byfrequency indication
1 Press the SET button for morethan one second.Keep pressing the SET buttonuntil the display secitonparameters start to flash.
2 Press the SET button repeatedlyuntil the frequency indicationappears and starts flashing.
3 Press the + or – button to selectthe frequency.
4 When the desired frequencyappears, leave the tuner for about10 seconds until the selectedchannel frequency stops flashingand the selection is stored inmemory.
Notes
• When you are setting the receptionchannel, the tuner can be used toreceive signals.
• Do not remove the batteries whilesetting the reception channel. If theyare inadvertently removed, re-insertthem immediately and redo theprocedure “Setting the receptionchannel” from step 1.
• Make sure that the selected channelis the same on the transmitter andtuner being used in the same system.
31
3 Do the following while thereis no signal transmission.Set the POWER switch to OFF tocomplete the setting, or press theSET button to set other items.The results are stored in memory.The change becomes effective thenext time you turn on thetransmitter by setting the POWERswitch to ON.
Resetting theaccumulated batteryuse time indication
The procedure below is thesame for all UWP seriestransmitters (UTX-B1/H1) andthe portable diversity tuner(URX-P1).
The accumulated battery use time isthe total time (in hours and minutes)that the batteries have been used. It isrecorded whenever the transmitter/microphone/tuner is on.Reset the indication to “00:00”whenever you replace the batteries.
1-a For transmitters (UTX-B1/H1)Turn on the unit while pressingdown the SET button.
1-bFor the portable diversitytuner (URX-P1)Press down the SET button formore than one second.Keep pressing the SET buttonuntil the display sectionparameters start to flash.
2 Press the SET button repeatedlyuntil the accumulated timeindication appears in the displaysection.
3 Press the – button.The time indication resets to“00:00.”While “00:00” is still displayed,you can return to previous valueby pressing the + button.
4-a For transmitters (UTX-B1/H1)Set the POWER switch to OFF tocomplete the setting, or press theSET button to set other items.The results are stored in memory.The change becomes effective thenext time you turn on the unit bysetting the POWER switch to ON.
4-bFor the portable diversitytuner (URX-P1)Leave the tuner for about 10seconds until the time indicationstops flashing and the setting isstored in memory.
Settings
32
Setting the RF outputlevel
The procedure below is thesame for all UWP seriestransmitters (UTX-B1/H1).
You can select an RF output level ofH (10 mW) or L (2 mW) in settingmode. Set the RF output level to L (2mW) for simultaneous operation ofmultiple channels, and set it to H (10mW) for long-distance operation.
1 Turn on the transmitter whilepressing down the SET button.
2 Press the SET button repeatedlyuntil the RF output levelindication appears in the displaysection.
3 Press the + button to select H (10mW), or press the – button toselect L (2 mW).
4 Set the POWER switch to OFF tocomplete the setting, or press theSET button to set other items.The results are stored in memory.The change becomes effective thenext time you turn on thetransmitter by setting the POWERswitch to ON.
Setting the monitorlevel (portable diversitytuner (URX-P1) only)
You can set the monitor level formonitoring the tuner output within therange of 01 to 24.
1 While the parameters on thedisplay section are not flashing,press the + or – button once.The monitor level indicationappears in the display section.
2 Press the + button to increase themonitor level, or press the –button to decrease the level.When you leave the tuner forabout two seconds or more,current monitor level setting isstored in memory and the normaldisplay resumes. Note thatmonitor level setting is effectiveafter you turn off the tuner, thenturn it on again.
33
Operation
The procedure below is thesame for all UWP seriescomponents (UTX-B1/H1 andURX-P1/R1/M1).
1 Make all necessary connectionson the tuner.For examples of UWP seriescomponent connections, see“System Configurations” on page34.
2 Set the transmission channel onthe transmitter, and then turn offthe unit.For details on setting thetransmission channel, see “Settingthe transmission channel” onpage 28.
3 Turn on the tuner.The parameters that were in thedisplay section when the tunerwas last turned off appear again.
Note
Before turning on the tuner, turndown the volume of theequipment connected to the tuner.Otherwise, noise will be producedwhen the tuner is turned on.
4 Set the reception channel on thetuner.For details on setting thereception channel, see “Settingthe reception channel” on page29.
5 Turn on the transmitter.
If noise is heard
Depending on the environment wherethe UWP series components areinstalled, external noise or radiowaves may disrupt transmission oncertain channels.When selecting a channel under thesecircumstances, turn off the transmitter.Then, on the tuner, select a channel forwhich the RF indications do notappear in the display section or forwhich the RF indicator does not lightup (i.e., a channel free from noise orradio wave interference). Set the samechannel on the transmitter.
Note
To prevent interference or noise,please take the following precautions.• Do not use two or more transmitters
with the same wireless channels.• When operating two or more UWP
series simultaneously, set each seriesto a different channel within thesame channel group.
• Keep the reception antenna and thetransmitter separated more than 3meters (9 feet 11 inches).
• When operating two or more UWPseries simultaneously with the samechannel group, make sure that theyare at least 100 meters (330 feet)apart, but within clear sight of eachother. (The actual distance maydiffer depending on thecircumstances.)
System Configurations
34
System Configurations
The UWP series is used in the following configurationexamples.
Sample configurations for ENG (Electronic NewsGathering) or EFP (Electronic Field Production) witha digital camcorder
Body-pack transmitter(UTX-B1)
Portable diversity tuner(URX-P1) (with the shoemount adapter attached)
DSR-PDX10/PDX10P/PD150/PD150PDVCAM Digital Camcorder
or
Hand-held microphone(UTX-H1)
Portable diversity tuner(URX-P1) (with the shoemount adapter attached)
DSR-PDX10/PDX10P/PD150/PD150PDVCAM Digital Camcorder
1 XLR-BMP conversion cable (supplied)2 Lavalier microphone (supplied)
35
Sample configurations for AV presentations
or
Body-packtransmitter(UTX-B1)
Portable diversity tuner (URX-P1) (withthe shoe mount adapter attached)
Hand-heldmicrophone(UTX-H1)
To DVD player,PC, or VTR, etc.
SRP-X700P Powered Mixer
Hand-heldmicrophone(UTX-H1)
Half-rack size diversitytuner (URX-R1)
To DVD player,PC, or VTR, etc.
Body-pack transmitter(UTX-B1)
AN-820 UHFantenna
SRP-X700PPowered Mixer
Diversity tunermodule (URX-M1)
1 XLR cable with the XLR-BMP conversion cable (supplied)2 Lavalier microphone (supplied)3 BNC cable4 XLR cable or pin cable
System Configurations
36
Sample configuration of a PA system
Hand-held microphone (UTX-H1)
AN-820 UHF antenna
Diversitytuner module(URX-M1)
Body-pack transmitter(UTX-B1)
To DVD player, PC,or VTR, etc. SRP-X700P
Powered Mixer
Diversity tunermodule (URX-M1)
1 Lavalier microphone (supplied)2 BNC cable3 XLR cable4 XLR cable or pin cable
*1 WD-820A Antenna Divider*2 MB-806A Tuner Base Unit*3 SRP-X100 Audio Mixer
37
Error Messages
When a problem occurs, one of the following error messages may appear on thedisplay.
Messages Meanings Remedy
Err 01 An error has occurred in the backup memorydata.
Contact your Sony dealer.
Err 02 The PLL synthesized circuit is abnormal. Restart the unit. If themessage appears again,contact your Sony dealer.
Err 03* The battery voltage exceeds the allowable limit. Use the specified batteries.
* Body-pack transmitter (UTX-B1)/hand-held microphone (UTX-H1)/portable diversity tuner(URX-P1) only.
Troubleshooting
38
Troubleshooting
If you have any problem using the UWP system, use the following checklist.Should any problem persist, consult your Sony dealer.
Symptom Meanings/Remedy
* Body-pack transmitter (UTX-B1)/hand-held microphone (UTX-H1)/portable diversity tuner(URX-P1) only.
The unit does not turn on*. The polarity orientation of the batteries in the batterycompartment is incorrect. b Insert the batteries withthe correct polarity orientation.
The batteries are exhausted. b Replace the batterieswith new ones.
The battery terminals in the transmitter are dirty. bClean the + and – terminals with a cotton swab.
The batteries become drainedquickly*.
The batteries are exhausted. b Replace the batterieswith new ones.
Manganese batteries are being used. b Use alkalinebatteries. The battery life of a manganese battery isless than half that of an alkaline battery.
The UWP series is being used under cold conditions.b The batteries drain quickly under cold conditions.
The channel cannot be changed. An attempt was made to change the channel bypressing the SET button only. b Restart the unit whileholding down the SET button. Then change thechannel with the + and – buttons.
There is no sound. The channel setting on the transmitter is different fromthat on the tuner. b Use the same channel setting onboth the transmitter and tuner.
The RF indications (RF indicator) on the tuner do notappear at all (or does not turn on). b Confirm that thetransmitter is turned on.
The sound is weak. The attenuation level on the transmitter is too high. bThe output level of the transmitter is low. Press the +button on the transmitter in attenuation level settingmode to decrease the attenuation level.
The volume on the amplifier or mixer is low. b Adjustthe volume.
39
Symptom Meanings/Remedy
There is distortion in the sound. The attenuation level of the transmitter is too low. bThe input level of the tuner is extremely high. Pressthe – button on the transmitter in attenuation levelsetting mode to raise the attenuation level.
The transmitter and the tuner are set to differentchannels. b Set the transmitter to the same channel.
There is sound interruption ornoise.
The RF indications on the tuner appear (the RFindicator lights up) even when the transmitter is off. bJamming radio waves are being received. Determinewhich channels are usable (i.e., channels for whichthe RF indications on the tuner do not appear (or forwhich the RF indicator on the tuner does not light up)and set the tuner and transmitter to the same usablechannel. When two or more transmitters are usedsimultaneously, use another channel group that isunaffected by jamming radio waves.
The transmitter and the tuner are set to differentchannels. b Set the transmitter to the same channel.
Two or more transmitters are set to the same channel.b Set each transmitter to a different channel.
The transmitters are not set to the channels within thesame channel group. b The channel plan which theUWP series components use is set so that no signalinterference occurs when 2 to 12 transmitters areused simultaneously. Set each transmitter to adifferent channel within the same channel group.
Specifications
40
Specifications
Transmitters (UTX-B1/H1)
Items common to alltransmitters
Oscillator typeCrystal-controlled PLL
synthesizerCarrier frequencies
794 to 806 MHzOperating frequency band
12 MHzRF output level
10 mW/2 mW selectablePre-emphasis
50 µsReference deviation
±5 kHzFrequency response
50 Hz to 18 kHzDistortion
1.0% or lessSignal-to-noise ratio
60 dB or moreTone signal
32 kHzAttenuation
0 to 21 dB, in 3-dB stepsDisplay Channel, frequency, audio
level, RF level,accumulated battery usetime
Indicator Power onPower requirements
3.0 V DC (two LR6/AA-size alkaline batteries)
Battery lifeApprox. 6 hours
Body-pack transmitter(UTX-B1)
Antenna 1/4λ (wave length) wireAudio input connector
3.5-mm dia. mini jackAudio input level
–60 dBV to –39 dBVDimensions
63 × 100 × 27 mm (2 1/2 × 4× 1 1/8 inches) (w/h/d)(excluding the antennas)
Mass Approx. 140 g (5 oz)including batteries
41
Hand-held microphone(UTX-H1)
Microphone unitDynamic
DirectivityUnidirectional
Antenna 1/4λ (wave length) wire(internal)
Dimensions
φ 52 × 240 mm (2 1/8 × 9 1/2
inches) (dia/length)Mass Approx. 300 g (11 oz)
including batteries
Tuners (URX-P1/R1/M1)
Items common to all tuners
Type of receptionSpace diversity
Oscillator typeCrystal-controlled PLL
synthesizerReception frequencies
794 to 806 MHzOperating frequency band
12 MHzSignal-to-noise ratio
60 dB or moreDe-emphasis
50 µsReference deviation
±5 kHzFrequency response
50 Hz to 18 kHzDistortion
1.0% or less at 1 kHzmodulation
Tone signal32 kHz
Indicator RF input level
Portable diversity tuner(URX-P1)
Antenna 1/4λ (wave length) wire(adjustable angle)
Squelch level15 dBµ
Audio output level–58 dBm
Audio output connector3.5 mm dia. mini jack
Headphones output level5 mW (16Ω)
Specifications
42
Display Channel, frequency, audiolevel, RF level,accumulated battery usetime, monitor level
Power requirements3.0 V DC (two LR6/AA-
size alkaline batteries)Battery life
Approx. 6 hoursDimensions
63 × 100 × 30 mm (2 1/2 × 4× 1 3/16 inches) (w/h/d)(excluding the antennas)
Mass Approx. 180 g (6 oz)including batteries
Half-rack size diversity tuner(URX-R1)
Antenna 1/4λ (wave length) wire(adjustable angle)
Squelch level25 dBµ
Balanced audio output level–28 dBm (LINE level)/–58
dBm (MIC level)selectable
Unbalanced audio output level–30 dBm
Audio output connectorsXLR-3-32 type, balanced1/4-inch jack, unbalanced
(LINE level only)Headphones output level
5 mW (16Ω)Display Channel, frequencyPower requirements
9.0 V DCDimensions
212 × 44 × 209 mm (8 3/8 ×1 3/4 × 8 1/4 inches) (w/h/d)(excluding the antennas)
Mass Approx. 1.3 kg (2 lb 14 oz)
43
Diversity tuner module(URX-M1)
Squelch level25 dBµ
Display Channel, frequencyDimensions
57 × 26 × 121 mm (2 1/4 × 11/16 × 4 7/8 inches) (w/h/d)
Mass Approx. 150 g (5 oz)
Design and specifications are subjectto change without notice.
Appendix
44
Appendix
Wireless microphone system frequency list
The following tables show the channels and frequencies selectable on yourwireless microphone, transmitter and tuner.The group 00 permits the unit to operate on any of 47 carrier frequencies in 125kHz steps of TV channels 68 and 69.For the setting procedures of the transmitting channels/frequencies on your unit,refer to the Instruction Manual of your unit. Be sure to save this list together withthe Instruction Manual of your unit.
Guidance on the use of a multi-channel system
When building up a multi-channel system, Sony recommends that one of thegroups listed under “Groups for the tuner” is selected to avoid mutual interferencefrom other Sony wireless microphones/transmitters.
Group for transmitter and tuner
Group 00
TV-68 TV-69
CH CH MHz CH MHz CH MHzMHz68-01 794.125 68-25 797.125 69-01 800.125 69-25 803.12568-02 794.250 68-26 797.250 69-02 800.250 69-26 803.25068-03 794.375 68-27 797.375 69-03 800.375 69-27 803.37568-04 794.500 68-28 797.500 69-04 800.500 69-28 803.50068-05 794.625 68-29 797.625 69-05 800.625 69-29 803.62568-06 794.750 68-30 797.750 69-06 800.750 69-30 803.75068-07 794.875 68-31 797.875 69-07 800.875 69-31 803.87568-08 795.000 68-32 798.000 69-08 801.000 69-32 804.00068-09 795.125 68-33 798.125 69-09 801.125 69-33 804.12568-10 795.250 68-34 798.250 69-10 801.250 69-34 804.25068-11 795.375 68-35 798.375 69-11 801.375 69-35 804.37568-12 795.500 68-36 798.500 69-12 801.500 69-36 804.50068-13 795.625 68-37 798.625 69-13 801.625 69-37 804.62568-14 795.750 68-38 798.750 69-14 801.750 69-38 804.75068-15 795.875 68-39 798.875 69-15 801.875 69-39 804.87568-16 796.000 68-40 799.000 69-16 802.000 69-40 805.00068-17 796.125 68-41 799.125 69-17 802.125 69-41 805.12568-18 796.250 68-42 799.250 69-18 802.250 69-42 805.25068-19 796.375 68-43 799.375 69-19 802.375 69-43 805.37568-20 796.500 68-44 799.500 69-20 802.500 69-44 805.50068-21 796.625 68-45 799.625 69-21 802.625 69-45 805.62568-22 796.750 68-46 799.750 69-22 802.750 69-46 805.75068-23 796.875 68-47 799.875 69-23 802.875 69-47 805.87568-24 797.000 69-24 803.000
45
Groups for tuner
Group 11Grouping 11 channels.
68-05 794.62568-14 795.75068-25 797.12568-41 799.12568-47 799.87569-12 801.50069-16 802.00069-30 803.75069-37 804.62569-40 805.00069-42 805.250
CH MHz
Group 12Grouping 8 channels.
Group 13Grouping 8 channels.
69-01 800.12569-05 800.62569-11 801.37569-25 803.12569-28 803.50069-36 804.50069-41 805.12569-43 805.375
CH MHz68-03 794.37568-13 795.62568-18 796.25068-26 797.25068-37 798.62568-40 799.00068-44 799.50068-46 799.750
CH MHz
Group A2Grouping 7 channels.
Group A3Grouping 7 channels.
CH MHz CH MHz69-11 801.37569-22 802.75069-30 803.75069-36 804.50069-40 805.00069-43 805.37569-45 805.625
68-10 795.25068-21 796.62568-29 797.62568-35 798.37568-39 798.87568-42 799.25068-44 799.500
Group L1Grouping 7 channels.
Group H1Grouping 7 channels.
Group H2Grouping 7 channels.
CH MHz
CH MHz CH MHz
68-09 795.12568-11 795.37568-19 796.37568-25 797.12568-30 797.75068-34 798.25068-37 798.625
68-10 795.25068-13 795.62568-17 796.12568-22 796.75068-28 797.50068-36 798.50068-38 798.750
69-10 801.25069-13 801.62569-17 802.12569-22 802.75069-28 803.50069-36 804.50069-38 804.750
Group A1Grouping 8 channels.
CH MHz68-06 794.75068-20 796.50068-24 797.00068-40 799.00069-04 800.50069-17 802.12569-23 802.87569-47 805.875
Group L2Grouping 7 channels.
CH MHz
69-09 801.12569-11 801.37569-19 802.37569-25 803.12569-30 803.75069-34 804.25069-37 804.625
Appendix
46
AC adapter for use with the URX-R1
Please prepare an AC adapter which satisfies the following conditions for normaloperation of the URX-R1 Half-rack Size Diversity Tuner.
• SpecificationsAC input voltage: Differs according to the countries.DC output voltage: 9.0 V DCRated load current: more than 300 mA DC
• The size of the DC output connector (DC jack)
Sony Corporation Printed in Korea