Electrical, Parts & Troubleshooting ManualFor Pachislot, Pachisuro or Kaidoshiki Yugiki

Wiring from the Aristocrat / Rodeo / Sammy

-NOTICE-

This manual is prepared for the use of entertainment only. To the best of my knowledge the information gathered here by myself in this document is accurate about the Aristocrat, Rodeo & Sammy Pachislot machines. In no way, shape or form is this document associated with the KK Aristocrat Technologies, Inc., Rodeo Corporation and or the Sammy Corporation. In no way shape or form does the author, Aristocrat Technologies, Inc., Rodeo Corporation and or the Sammy Corporation take any responsibility for the accuracy of the data in this document or how it may be used. You the reader take full responsibility for any damages that may occur to any Pachislot machine by means of this documentation. This document has been put together as an aid for learning about the operation of the Pachislot machines and is strictly to be used for entertainment purposes only.

------------------------------------------------------------------------------------ Written by Charlie C. Form #0001 Rev. B 2014

TABLE OF CONTENTS

GENERAL INFORMATION………………………………………………………..……… 3 Introduction………………………………………………………………………… 3 General Information………………………………………………………………. 3 Lubricants & Cleaners …………………………………………………………… 3 Internal Component Locations…..……………...………………………………. 5 External Component Locations…..………..…….……………………………… 6ELECTRICAL WIRING OF MACHINE………………………………………………….. 7 Wiring Diagram of Machine……………………………………………………… 7 Typical Wiring of Cables………………………………………………………… 8 Ribbon Cable Wiring…………………………………………………………….. 9-10ELECTRICAL & MECHANICAL OPERATION…………………………………………. 11 Audio Sound Board……………………………………………………….……… 11-12 Control Input Board…………………………………………………….………… 13-14 CPU System Infrastructure Board……………………………………………… 15 Fluorescent Starter Board & Light Bulbs………………………………...…….. 16-17 Frame Lighting Boards…………………………………………………………... 18 Belly Glass………………………...………………………………………………. 19 Hopper………………………………………………………….………………….. 20-21 L.C.D. Display Board…………..…………………………………………………. 22 Medal (Token) Acceptor……………………………………………..…………… 23 Power Supply…………………………………………….………….....……..…... 24-25 Power Supply Control Board……….………………………….…….....……….. 26-27 Power Supply Service Board……………………………………………..……… 28-29 Reels…………………………………………………………….…………………. 30 Reel Light Board & Light Bulbs……………………………..………………..….. 31 Reel Light Control Board………………………………….……………..………. 32 Reel Motor Control Board………………………………..……………..………... 33 Relay Status Board (Intensive External Terminal Board)…..………..……….. 34-36 Skill Stop Board……………………………………………….…………………… 37 Special Chance Lighting Board…..……………………………………………… 38 Start Lever Spin Knob…………………………………………………….………. 39MISC. PARTS LIST……………………………………………………….………………… 40PACHILSO ERROR CODES………………………...……….……………………………. 41IMPORTANT WEBSITES & INFO………………………………………….……………… 42

2

GENERAL INFORMATIONDisconnect the electric power to

the machine before any servicing of the unit can begin.

SPECIFICATIONSElectrical 110VAC 50/60HZ 10Amps24VAC 6-10Amps Internal Voltages

Weight70-95 lbs.

Measurements34”x24”x13” H*W*L

TOOLS REQUIREDStandard set of hand toolsVolt Meter Field Service Grounding Kit

CLEANER & POLISHERSRubbing Alcohol - Medals (Tokens)Acceptor & hopperElectrical Spray - sensors & switches, & hopperMild dish detergent - glass, reels and exterior of unit. Novus Plastic Polish - for any plastic exterior of unit.

GENERAL INFORMATIONPachislot, Pachisuro, Kaidoshiki Yugiki, or Pachislot is the Japanses Skill Slot Machine. Flash memory is used to preserve credits, last game, etc.

AGEThe Pachislot can be in service for no more than

2 years in a Pachi Parlor in Japan.

MEDALS (TOKENS) ACCEPTEDBYOAC and MAME Medals (Tokens) size is .984 or 25mm in size. Medals (Tokens) weigh about 4.4 oz. or 124.73 grams on average. A bet consist of 1 to 3Medals (Tokens) and play across 1-7 different lines per spin. Max of 53 Medals (Tokens) credits can be held by the machine for credit at any one given time. The hoppercan hold about 1,200 Medals (Tokens) max.

BOARD INFORMATIONAll Boards with the beginning part # of SS were manufactured for the Sammy Corporation by the CMK Electronics WUXI.

REEL STOP BUTTONS It is preferable that the operation of the stop button has a structure for stopping the rotation of the rotating cylinder corresponding to the stop button and that there is no irregularities. The player operates the stop button and the reel must stop within 0.19 seconds of the stop button associated to the real has been pressed. The reels can't slip no more than 4 symbols.

REEL INFORMATION21 symbols patterns per reel, not to exceed 10 different symbols per game. Reels are 3 1/8” in. 79.375 mm wide Symbols patterns are 3” in. 76.200 mm wide by 1 ¼” in. 31.7500 mm with a space of 1/8” in. 9.525 mm in between Symbols patterns. Reels may not spin faster than 80 revolutions per minute, and muststop within 0.19 seconds of the stop button associated to the real has been pressed. The reels can't slip no more than 4 symbols.

Jackpot Payout’s can range from 60% - 160% 200 % if skill is used. 6 payout levels, level 6 being the highest payout level. * Level 4 or 5 = A.C. & Las Vegas odds 88 - 160%

Reel Symbols and CombinationsSymbols * number of reels = possible combinations21 symbols per reel \ 2 reels = 441 possible combinations.21 symbols per reel \ 3 reels = 9,261 possible comb.21 symbols per reel \ 4 reels = 194,481 possible comb.21 symbols per reel \ 5 reels = 4,084,101 possible comb.21 symbols per reel \ 6 reels = 85,766,121 possible comb.

TYPES OF MACHINESTYPE A _Big Bonus Machine - Bonus round mode usually give at least 24 spins and 24 guaranteed wins. Big Bonus round is 2 or 3 sets with at least 8 guaranteed in a row wins. The playeris guaranteed a win for each spin. The player needsto hit a certain combination usually the replay symbols to get into the bonus round. Total winningsis usually 400 – 711 Medals (Tokens) per Big Bonus round.Regular Bonus pay out is a 15:1 ratio. This means for every 1 medal token played, 15 Medals are returned to the player. Max return of Medals (Tokens) is 110, and will end when Big Bonus Ends.

TYPE B_Challenge Chance - The same features of a Type A machines with a Big Challenge added. You can have the chance to play over 200 consecutive games up to 15 minutes with the increased odds to win above medals tokens. 3 otherfeatures of Pachislot machines are "Stock," “Renchan”, and “Tenjō”. The game makes the reels stop instead of slipping off the bonus symbols for a few games. A Big Bonus Game could end and new Big Bonus game start eventually paying out up to 10,000 Medals (Tokens) at one time.

3

LOCATIONS:

Interior Part Locations:

4

5

Exterior Part Locations:

6

ELECTRICAL & MECHANICAL OPERATION:

Wiring Diagram of the Machine:

7

Typical Wiring of Cables

Cable #1

Pin # - color wire Pin # - color wire

1 Brown 13 Orange / White2 Red 14 Yellow / White3 Orange 15 Green / White4 Yellow 16 Blue / White5 Green 17 Purple / White6 Blue 18 Grey / White7 Purple 19 White / Black8 Grey 20 Black9 White 21 Brown10 Black 22 Red11 Brown / White 23 Orange12 Red / White 24 Yellow

Cable #2

Pin # - color wire

1 White / Black2 Black3 Brown4 Red5 Orange6 Yellow

Cable #3 Speaker Wiring

Pin # - color wire

1 Red, Blue or Black 2 White

8

Ribbon Cable Wiring (AWM Standard IDE Cable)

Reel Motor Control Board CN2 Header 30 pins & Relay Status Board CN1 Header 30 pins

to Reel Motor Control Board CN1 Header 40 pins &

CPU System Infrastructure Board CN4 Header 40 pins

Reel MotorControl

Board CN2 /RelayStatusBoard

CN1 pin #Cable

Reel MotorControl

Board CN1 /CPU System Infra. BoardCN4 pin #

Cable

Description

1 35, 36 +24Vdc

2, 4, 2733, 34,

37,38, 39Ground & Signal wires for all reels home switchesRelay Motor Control BD CN4 pin2, CN6 pin 2, & CN8 pin 2

3 22 After Bonus Reset Input Line

5 17CT Bonus - Relay Status Board -+24vdc Coil of Signal Switching Relay #5 Fujitsu #SY24WK

6 18BB Bonus - Relay Status Board +24vdc Coil of Signal Switching Relay #4 Fujitsu #SY24WK .

7 19RB Bonus - Relay Status Board +24vdc Coil of Signal Switching Relay #3 Fujitsu # SY24WK

8 20Token Out - Relay Status Board+24vdc Coil of Sensitive Signal Relay #Omron #G6E-134P

9 21Token In - Relay Status Board +24vdc Coil of Sensitive Signal Relay #Omron #G6E-134P

10 16Casino Fault Monitoring Lines & Relay Motor Control BDCN3 pin 5 (voltage to Left Reel Motor) +24vdc

11 15Casino Fault Monitoring Lines & Relay Motor Control BDCN3 pin 4 (voltage to Left Reel Motor) +24vdc

12 14Casino Fault Monitoring Lines & Relay Motor Control BDCN3 pin 3 (voltage to Left Reel Motor) +24vdc

13, 23 13Casino Fault Monitoring Lines & Relay Motor Control BDCN3 pin 2 (voltage to Left Reel Motor) +24vdc

14 1,2,3,4Casino Fault Monitoring Lines & Relay Motor Control BD CN3 Pin1, CN5 pin 1, CN7 pin1 & Power for LED D2

15 12Casino Fault Monitoring Lines & Relay Motor Control BDCN5 pin 5 (voltage to Center Reel Motor) +24vdc

16 11Casino Fault Monitoring Lines & Relay Motor Control BDCN5 pin 4 (voltage to Center Reel Motor) +24vdc

17 10Casino Fault Monitoring Lines & Relay Motor Control BDCN5 pin 3 (voltage to Center Reel Motor) +24vdc

18 9Casino Fault Monitoring Lines & Relay Motor Control BDCN5 pin 2 (voltage to Center Reel Motor) +24vdc

19 8 Casino Fault Monitoring Lines & Relay Motor Control BD

CN7 pin 5 (voltage to Right Reel Motor) +24vdc

20 7Casino Fault Monitoring Lines & Relay Motor Control BDCN7 pin 4 (voltage to Right Reel Motor) +24vdc

21 6Casino Fault Monitoring Lines & Relay Motor Control BDCN7 pin 3 (voltage to Right Reel Motor) +24vdc

22 5Casino Fault Monitoring Lines & Relay Motor Control BDCN7 pin 2 (voltage to Right Reel Motor) +24vdc

24Left Reel #1 Stop Control Out (Left Stop Button pressed) Ground of LED D6 (see Reel Motor Control Board CN1 pin 28)

25

Center Reel #2 Stop Control Out (Center Stop Button pressed) Ground of LED D7 (see Reel Motor Control Board CN1 pin 27)

26Right Reel #3 Stop Control Out (Right Stop Button pressed) Ground of LED D8 (see Reel Motor Control Board CN1 pin 26)

28 31 Left Reel #1 Stop Control Input29 30 Center Reel #2 Stop Control Input30 29 Right Reel #3 Stop Control Input

23 Right Reel #1 Home Position Switch activated LED D524 Center Reel #2 Home Position Switch activated LED D4 25 Left Reel #3 Home Position Switch activated LED D3

26Right Reel #3 Stop Control Out (Right Stop Button pressed) Power wire of LED D8

27Center Reel #2 Stop Control Out (Center Stop Button pressed) Power wire of LED D7

28Left Reel #1 Stop Control Out (Left Stop Button pressed) Power wire of LED D6

32Power wires for all reels home switchesRelay Motor Control BD CN4 pin 1, CN6 pin 1 & CN8 pin 1

40 Ground for D2 (power on LED) * CN4 - CN8 are found on the Reel Motor Control Board.

* Ribbon Cables are AWM IDE 300v internal appliance wiring cables.

10

Audio Sound BoardPart # SS09BC64

Manufactured by: Sammy

• The sticker on the protective cover on the board says;” B88CC 0048K”• Audio Chip is a Yamaha #YM2735-F and the board was made by BellCo.

The Audio Board puts out the audio, special lighting effects, and Top and Belly Glass Lighting.

CN1 Header 11 pins to L.C.D Board CN1 Header 11 pinsCN2 Header 12 pins to Frame Lighting Board Cable splits into 2 cable headers to Top Frame Lighting Board CN1 Header 6 pins and CN2 Header 6 pinsCN3 Header 24 pins cable splits into 2 cables Special Chance Lighting Board CN1 Header 6 pins & Reel Light Control Board CN1 Header 18 pins.CN4 Header 2 pins to Right Speaker pin 1 (+) wire - 8ohm, 10w per speaker pin 2 is ground. 1 speaker only per twin set of wiresCN5 Header 3 pins to Fluorescent Starter Board CN1 Header 3 pins * Playing Field Glass LightingCN6 Header 16 pins to C.P.U System Infrastructure Board CN1 Header 16 pins CN7 Header 3 pins to Fluorescent Starter Board CN1 Header 3 pins * Top Belly Glass LightingCN8 Header 2 pins to Left Speaker pin 1 (+) wire - 8ohm, 10w per speaker pin 2 ground. 1 speaker only per twin set of wires

IC2 CMOS chipIC4 Roland RDAC RPP-8 is a Roland Digital Audio Compression ChipIC5 32Mbit UV Eprom & OTP Eprom

11

CN2 Header 12 pin to Frame Lighting Board Cable splits into 2 cables to

Top Center Lighting Board CN1 Header 6 pin & CN2 Header 6 pin

CN2 pin #-

Frame Lighting Board CN1 pin # / CN2 pin #

1 brown - CN1 - 1 2 Red - CN1 - 2 3 Orange - CN1 - 3 4 Yellow - CN1 - 4 5 Green - CN1 - 5 6 Blue - CN1 - 6 7 Purple - CN2 - 1 8 Grey - CN2 - 2 9 White - CN2 - 3 10 Black - CN2 - 4 11 Brown / White - CN2 - 5 12 Red / White - CN2 - 6

Straight Thru Cable

CN3 Header 24 pin - Cable splits into 2 cablesSpecial Chance Lighting Board - CN1 Header 6 pin

& Reel Light Board - CN1 Header 18 pin

CN3 pin 19-24to

Special Chance Lighting Board CN1 Header 6 pins

19 White / Black - 1 - Ground 20 Black - 2 - LP1 21 Brown - 3 - LP2 22 Red - 4 - LP3 23 Orange - 5 - LP4 24 Yellow - 6 - LP5

CN3 pin 1-18 toReel Lighting Board CN1 Header 18 pins

1 - 18 - 1 - 18Straight Thru Cable

12

Control Input BoardPart # SS07DC02

Manufactured by: Sammy

CN1 Header 3 pins to Door Reset Switch - soft system reset.CN2 Header 2 pins to Medals (Tokens) Acceptor Dump Solenoid - discharges everything that is not a parlor Medals (Tokens).CN3 Header 6 pins to Medals (Tokens) Sensors #1 and #2.CN4 Header 11 pins to Skill Stop Board CN1 Header Reel Stop Switches.CN5 Header 6 pins to Start Lever, & Max Bet Switch.CN6 Header 50 pins to C.P.U. Main Board System Infrastructure Board CN3 HeaderCN7 Header 6 pins to Credit / Cash Out, 1 Bet, and 2 Bet Switches.CN8 Header 2 pins to Lower Belly Fluorescent Starter Board CN1 HeaderD1,D2 - Credits Readout - Total of Medals (Tokens) Played.D3,D4,D5 - Game Count - Total Credits Payed Out To Player.D6,D7 - Credits Won - Total Credits Just won.D8 - Programmed Pay Back Percentage Level #1-6.D9,D10 - Start LED - Indicate Bets Made Ready to Spin Reels.D11 - 3 Medals (Tokens) Bet.D12 - 2 Medals (Tokens) Bet.D13 - 1 Medals (Tokens) Bet.D14,D16,D18,D20 - Special Function or Entertainment Lighting.D22 - Medals In - Machine is ready for Medals (Tokens) to be inserted.D23 - Replay Light – A free replay is ready.D24 - Power LED On = Power On /Off.D25 - Start Lever Off = activated / On = not activated.D26 - Max Bet On = activated / Off = not activated.D27 - 2 Medals (Tokens) Switch On = activated / Off = not activated.D28 - 1 Medals (Tokens) Switch On = activated / Off = not activated.D29 - Credit / Cash Out Switch On = activated cash out credits / Off = credits held.D30 - Left Reel Stop Switch on Skill Stop Board On = not activated / Off = activated.D31 - Center Reel Stop Switch on Skill Stop Board On = not activated / Off = activated.D32 - Right Reel Stop Switch on Skill Stop Board On = not activated / Off = activated.D33 - Door Reset Switch soft system reset On = not activated / Off = activated.D37 - Medals (Tokens) Sensor #1 On = sensor blocked / Off = sensor unblocked.D38 - Medals (Tokens) Sensor #2 On = sensor blocked / Off = sensor unblocked.SW1 - Programming Button - Used to set pay back percentages level #1-6.

13

CN1 Header 3 pin Door Reset Switch

Pin #Sharp Electronics Components # P1A23LC or 1A23LC is a

OPIC photo interrupter type switch replaced by part # GP1A23LC1 Vcc power supply 5vdc, D33 is on when not activated2 Ground3 Vo voltage out / signal wire

CN2 Header 2 pin Medals (Tokens) Acceptor Dump Solenoid

Pin # Marsh Bellofram #T32211 Vcc power supply 30vdc 2 Ground

CN3 Header 6 pin - Medals (Tokens) Acceptor Medals (Tokens) Sensors

Pin # Sharp Electronic Components # GP2A251 Vcc power supply 5vdc, Medals (Tokens) sensor #1 D37 off when not activated.2 Vo voltage out / signal wire, Medals (Tokens) sensor #1 D37 is on when blocked 3 Ground Medals (Tokens) sensor #1 4 Vcc power supply 5vdc, Medals (Tokens) sensor #2 D38 off when not activated.5 Vo voltage out / signal wire, Medals (Tokens) sensor #2 D38 is on when blocked6 Ground Medals (Tokens) sensor #2

CN5 Header 6 pins - Start Lever Switch, & Max Bet Switch

Pin # Shinkoh Elecronics Co. LTD # KI1232 Photo Interrupter Switch1 Brown Vcc power supply 5vdc, Start Lever Switch D25 is on when not activated.2 Red Vo voltage out signal wire, Start Lever Switch3 Orange Ground Start Lever Switch 4 yellow Vcc power supply in 5vdc, Max Bet Switch, D26 is off when not activated.5 Green Vo voltage out signal wire, Max Bet Switch6 Blue Ground Max Bet Switch

CN7 Header 6 pins – Credit / Cash Out, 1 Bet, 2 Bet Switches

Pin #Credit / Cash Out, 1 Bet, and 2 Bet Switches - Fujisoku Corp. #LTM1-3

super-minature pushbutton metal contact SPST switch

1 BrownVcc - power supply in 5vdc, Credit / Cash Out SwitchD29 on means cash out credits as tokens, off means credits are withheld.

2 Red Ground Credit / Cash Out Switch3 Orange Vcc power supply in 5vdc, 1 Bet Switch, D28 is off when not activated.4 yellow Ground 1 Bet Switch

5 GreenVcc power supply in 5vdc, 2 Bet SwitchD27 is off when not activated.

6 Blue Ground 2 Bet Switch

14

CPU System Infrastructure BoardPart # SS098BC02

Manufactured by: Sammy

• CPU is a Star Novax - LE 2080A-PA #T6W058N-0003 - Japan 0211 EAI* Z80 Microprocessor Core Based Instruction Set. LETECH is the Chinese manufacturing branch of Star Electronics of Japan. The Le 2080A-PA contains 2764 of one time programmable EPROM. Not erasable or reprogrammable. Electrically programmed through its data and address lines upon initialization. Sanyo also made this chip at one time.

CN1 Header 16 pins to Audio Sound Board CN6 Header 16 pins CN2 Header 20 pins to Power Supply Control Board CN3 Header 20 pinsCN3 Header 50 pins to Control Input Board CN6 Header 50 pinsCN4 Header 40 pins to Reel Motor Control Board CN1 Header 40 pinsD15 Power on lightD17 Power on light

15

Fluorescent Starter BoardPart # P-1096

Manufactured by: Otari

* Top Belly & Playing Field Glass Lighting

CN1 Header 3 pins to Audio Sound Board to CN5 & CN7 Header 3 CN2 Header 2 pins to Fluorescent Bulb #1 +12vdc

Audio Sound Board CN5 & CN7 Header 3 pins to CN1 Header 3 pins

Pin # Description 1 Brown Vcc power supply +12.43Vdc2 Red Ground3 Orange Ground

16

Fluorescent Starter BoardPart # P-1097

Manufactured by: Otari

* Lower Belly Glass Lighting

CN1 Header 2 pins to Control Input Board CN8 Header 2 pins CN2 Header 2 pins to Fluorescent Bulb #1 +12vdcCN3 Header 2 pins to Fluorescent Bulb #2 +12vdc

Control Input Board CN8 Header 2 pins to CN1 Header 2 pins

Pin # Description 1 Brown Vcc power supply +11.30Vdc2 Red Ground

Fluorescent Sub Miniature Bulbs are a T4-type wires soldered on both ends 12 ¼” x ¼” .27 L*W.

17

Frame Entertainment Lighting Boards Locations:Manufactured by: Sammy

SS09FC01 Light Board CN1 Header 6 pins & SS09FC01 Light Board CN2 Header 6 pins to SS09BC64 Audio Sound Board CN2 Header 12 pins

SS09FC01 Light Board CN3 Header 9 pins to SS09FC11 Light Board CN1 Header 9 pins SS09FC11 Light Board CN2 Header 6 pins to SS09FC31 Light Board CN1 Header 6 pins SS09FC31 Light Board CN2 Header 3 pins to SS09FC51 Light Board CN1 Header 3 pins

SS09FC01 Light Board CN4 Header 9 pins to SS09FC21 Light Board CN1 Header 9 pins SS09FC21 Light Board CN2 Header 6 pins to SS09FC41 Light Board CN1 Header 6 pins SS09FC41 Light Board CN2 Header 3 pins to SS09FC61 Light Board CN1 Header 3 pins

SS09FC01 CN4 Header 9 pins \ SS09FC21 CN1 Header 9 pins toSS09FC21 CN2 Header 6 pins \ SS09FC41 CN1 Header 6 pins toSS09FC41 CN2 Header 3 pins \ SS09FC61 CN1 Header 3 pins…

SS09FC11 CN1 9 pins To SS09FC31 CN1 6 pins To SS09FC51 CN1 3 pins

SS09FC21 CN1 9 pins To SS09FC41 CN1 6 pins To SS09FC61 CN1 3 pins1 - To LEDS - To LEDS2 - To LEDS - To LEDS3 - To LEDS - To LEDS4 - To LEDS - To LEDS5 - 5 - To LEDS6 - 4 - To LEDS7 - 3 - To LEDS8 - 2 - 29 - 1 - 3

Grayed Cells indicated a straight thru connection.

18

GlassBelly Glass

19

Hopper Model # JSH-777B 163489

Manufactured by: TAKADEN

20

CN4 pin# Description

1, 5 OrangeVcc power supply +6vdc, Home Switch & Count / Discharge Switch.D7 (Error #2) on the Power Supply is activated when a Medal (Token) is discharged from the hopper.

2, 6 Green Ground Medals (Tokens) Count / Discharge Switch.

3 BrownVo voltage out / signal wire Home Position Switch connected to CN6 pin 7

4 Red Vcc power supply +24VDC +/- 10% 0.58A, Hopper Motor

7 BrownVo voltage out / signal wire Medals (Tokens) Count / Discharge Switch.connected to CN6 pin 9

8 White Ground Hopper Motor

Pin #(on theswitch)

Hopper Medals Token Discharge Sensors - Shinkoh Elecronics Co. LTD # KI669

1 Vcc power supply +6vdc 2 Vo voltage out / signal wire 3 Ground

Pin # Hopper Motor - Sun # 259529C2E.Vcc power supply +24Vdc +/- 10% 0.58A power to motorGround

21

L.C.D. Display BoardPart # AD-501-A

Manufactured by: Alpha Device Co. LTD

CN1 Header 11 pin to Audio Sound Board CN1 Header 11 pins

22

Medals (Tokens) AcceptorModel # NS-130B or NS-130C

Manufactured by: Nippon ConClux Co.,LTD

* This Medal (Token) acceptor was made to only accept BYOAC and MAME Medals (Tokens).

Medals (Token) are about .984 (25mm) in size, and weigh about 4.4 oz. (124.73 grams).U.S. Quarters are about .956 (24.3mm) in size, and weigh about 0.20 oz. (5.67grams).

Medals (Tokens) Acceptor Dump Solenoid to Control Input Board CN2 Header 2 pins

Pin # Marsh Bellofram #T3221 Quick Firing Solenoid1 Vcc power supply 30vdc 2 Ground

Medals (Tokens) Acceptor Medals Token Sensors to Control Input Board CN3 Header 6 pin

Pin #Sharp Electronics #GP2A25

Light Modulation Reflection Type Photo Interrupter 1 Vcc Supply Power 5vdc Medals (Tokens) Sensor #1 2 Vo voltage out, signal wire 50ma trigger wire Sensor #1 D37 is on when blocked 3 Ground Medals (Tokens) sensor #14 Vcc Supply Power 5vdc Medals (Tokens) Sensor #25 Vo voltage out / signal wire 50ma trigger wire Sensor #2 D38 is on when blocked6 Ground Medals (Tokens) Sensor #2

23

Power Supply Control Box by SammyAristocrat / Rodeo/ Sammy

Payback Settings Programming Switch is also a Reset Switch for the machine.

24

IGT Power Supply Control Box by Sammy

Payback Settings Programming Switch is also a Reset Switch for the machine.

25

Power Supply BoardPart # SS07E06

Manufactured by: Sammy

CN1 Header 2 pins to Step down transformer 24VAC 6Amps power.CN2 Header 2 pins to Medals (Tokens) over flow switch would detect if Medals (Tokens) were overflowing out of hopper. The error code “OF” Medal Token overflow would appear.CN3 Header 20 pins to C.P.U. System Infrastructure Board CN2 Header 20 pins.CN4 Header 8 pins to Hopper motor and switches.CN5 Header 2 pins to Main Power Switch CN6 Header 13 pins to Power Supply Service Board CN5 Header 13 pinsCN7 Header 4 pins to Power Supply Service Board CN1 Header 4 pinsD15 Power on lightD17 Power on light F1 110VAC 10A AGW fuse

26

CN3 Header 20 pins to CN6 Header 13 pins

CN3 pin # LED D# To CNx pin # Description1+2+11+12 - NC Ground3+13 - NC Ground4+14 - NC Ground5+15 - CN6 pin 1 Ground6 - NC N/A7 D3 - CN6 pin 4 Hopper Medal Token Eject Service Switch8 - CN6 pin 12 Reset After Big Bonus Payout Switch9 D4 - CN6 pin 5 Payback Settings Program Switch10 D6 - CN6 pin 8 Hopper Home Position Switch Error LED #116 - NC N/A17 - NC N/A18 - CN6 pin 11 Credit Dump Switch19 D5 - CN6 pin 6 Reset Service Switch

20 D7 - CN6 pin 10Hopper Medals (Tokens) Discharge / Count Switch Error LED #2

* NOTE: In CN3 Column the D# are the LED # presented on the Power Supply Service Board. NC = no connection and N/A = data not available

CN6 Header 13 pins to Power Supply Service Board CN5 Headers 13 pinsTo CN3 Header 20 pins and CN4 Header 8 pins

CN6 pin# LED D#to Power Supply Service Board

CN5 pin#

toCN3 pin #CN4 pin #

Description

1 Brown - CN3 pin 5+15 Ground 2 Red D1 - NC Vcc power supply 110Vac Power on LED3 Orange D2 - NC Vcc power supply +12VDC power on LED4 Yellow D3 - CN3 pin 7 Hopper Medals (Tokens) Eject Service Switch5 Green D4 - CN3 pin 9 Payback Settings Program Switch6 Blue D5 - CN3 pin 19 Reset Service Switch7 Purple - CN4 pin 3 Ground - Hopper Home Position LED #18 Grey D6 - CN3 pin 10 Hopper Home Position Switch Error LED #1

9 White - CN4 pin 7Ground - Hopper Medals (Tokens) Discharge / Count Switch Error LED #2

10 Black D7 - CN3 pin 20Hopper Medals (Tokens) Discharge / Count Switch LED #2

11 Brown/Grey - CN3 pin 18 Credit Dump Switch12 Red / White - CN3 pin 8 Reset After Big Bonus Switch13 Orange / White

- NCGround - Reset Big payout & Credit Dump switches.

27

Power Supply Service BoardPart # SS07EC53

Manufactured by: Sammy

CN1 Header 4 pins to Power Supply Board CN7 Header 4 pins.CN2 Header 2 pins to Main power Switch.CN3 Header 2 pins to Payback Settings Program Switch.CN4 Header 2 pins to Reset Service Switch.CN5 Header 13 pins to Power Supply Board CN4 Header 8 pins.D1 - 110Vac power on LED.D2 - +12vdc power on LED.D3 - Hopper Medals (Tokens) Eject Service Button activated.D4 - Payback Settings Program Switch activated.D5 - Reset Service Switch activated.D6 - Hopper Home Position Switch Error LED #1D7 - Hopper Medals (Tokens) Discharge / Count Switch LED #2

CN1 Header 4 pin to Power Supply Board CN7 Header 4 pin

CN1 pin # to CN7 pin # Description1 - 1 Vcc power supply fuse F2 110V 6A2 - 2 Vo voltage out fuse F2 to CN3 pins 4 & 14

3 - 3 Vcc power supply fuse F1 110V 6A4 - 4 Vo voltage out fuse F1 CN3 pins 3 &13

28

CN5 Header 13 pins to Power Supply Board CN6 Headers 13 pins toCN2, CN3, CN4, &

Power Supply Board CN3 Header 20 pin & CN4 Header 8 pin

CN5 pin# &LED D# to

Power Supply Board CN6 pin#

toCN2 pin #CN3 pin #CN4 pin #

PowerSupplyBoard

CN3 pin #&

CN4 pin #

Description

1 Brown - NCCN3 pin 5+15

Ground - D1, D2 & D3

2 Red D1 - NC NCVcc power supply 110 Vac Power on LED

3 Orange D2 - NC NCVcc power supply +12VDC Power on LED

4 Yellow D3 - CN2 pin 1 CN3 pin 7Hopper Medals (Tokens) Eject Service Switch

5 Green D4 - CN3 pin 1 CN3 pin 9 Payback Settings Program Switch6 Blue D5 - CN4 pin 1 CN3 pin 19 Reset Service Switch7 Purple - NC CN4 pin 3 Ground - Hopper Home Position LED #1

8 Grey D6 - NC CN3 pin 10Hopper Home Position Switch Error LED #1

9 White - NC CN4 pin 7Ground - Hopper Medals (Tokens) Discharge / Count Switch Error LED #2

10 Black D7 - NC CN3 pin 20Hopper Medals (Tokens) Discharge / Count Switch Error LED #2

11 Brown/Grey - NC CN3 pin 18 Credit Dump Switch - connected to top & middle of switch #1 No input

12 Red/White - NC CN3 pin 8 Reset After Big Bonus Switch - connected to top & middle of switch #2 No input

13 Orange/White - NC NCGround - Resets Big payout &Credit Dump switches. connected to both switches #1 & #2 Bottom of switches.

*Switch #1 pin 11 on CN5 or Switch #2 pin 12 on CN5 are normally not connectedunless Grounded to Pin 13 on CN5 which would mean let machine automatically reset.

29

ReelsManufactured by: Sammy

STEPPER MOTOR INFORMATIONStepper Motor - Tamagawa Seiki Co. LTD #TS3103N294 24vdc 0.28A, 6.72W KW

Analog Photo Interrupter Switch - Shinkoh Elecronics Co. LTD # KI1669

REEL INFORMATION21 symbols patterns per reel, not to exceed 10 different symbols per game. Dimensions:Reels are 3 1/8” in. 79.375 mm wide Symbols patterns are 3” in. 76.200 mm wide leaving a 1/16” in. 1.5875 mm space on both sides of symbol pattern to the outside edge of the reel. The height of the Symbols patterns is 1 ¼” in. (31.7500 mm). The space of 1/8” in. (3.175 mm) is in between Symbols patterns.

30

Reel Light BoardPart # SS07RCO3 CMK

Manufactured by: Sammy

CN1 Header 5 pin

Pin # Description - T-5 12vdc light bulb built in to socket1 Ground 2 Vcc power supply +24vdc light bulb LP1 + LP23 Vcc power supply +24vdc light bulb LP3 + LP44 Vcc power supply +24vdc light bulb LP5 + LP65 Ground

31

Reel Light Control BoardPart # SS07RE52

Manufactured by: Sammy

• Toshiba #74hc175ap High Speed CMOS D-Type Flip-Flop with C2MOS technology.• This Board lights all of the reels.

CN1 Header 18 pins to Audio Sound Board CN1 Header 18 pins.CN2 Header 5 pins to Left Reel Light Board CN1 Header 5 pins.CN3 Header 5 pins to Center Reel Light Board CN1 Header 5 pins.CN4 Header 5 pins to Right Reel Light Board CN1 Header 5 pins.

CN2, CN3, CN4 Header 5 pins to Reel Light Board CN1 Header 5 pins

Pin # Description - T-5 12vdc light bulb built in to socket1 Ground 2 Vcc power supply +24vdc light bulb LP1 + LP23 Vcc power supply +24vdc light bulb LP3 + LP44 Vcc power supply +24vdc light bulb LP5+ LP65 Ground

32

Reel Motor Control Board Part # SS07RE01 CMK

Manufactured by: Sammy

CN1 Header 40 pins to CPU System Infrastructure Board CN4 Header 40 pins.CN2 Header 30 pins to Relay Status Board CN1 Header 30 pins.CN3 Header 5 pins to Left Reel Stepper Motor.CN4 Header 3 pins to Left Reel Home Position Switch.CN5 Header 5 pins to Middle Reel Stepper Motor.CN6 Header 3 pins to Middle Reel Home Position Switch.CN7 Header 5 pins to Right Reel Stepper Motor.CN8 Header 3 pins to Right Reel Home Position Switch.D2 - Power LED on = power supplied to board.D3 - Left reel home position switch LED on = home position.D4 - Middle reel home position switch LED on = home position.D5 - Right reel home position switch LED on = home position.D6 - Left stop button LED on = left stop button pressed and left reel should stop.D7 - Middle stop button LED on = middle stop button pressed and middle reel should

stop.D8 - Right stop button LED on = right stop button pressed and right reel should stop.

CN3, CN5, and CN7 Header 5 pins to Reel Motors

Pin # Stepper Motor made by Tamagawa Seiki Co. LTD 24v, 0.28A1 Ground wire white 2 red wire3 green wire4 blue wire5 yellow wire

CN4, CN6, and CN8 Header 3 pins to Reel Home Switch

Pin # Analog Photo Interrupter Switch - Shinkoh Elecronics Co. LTD # KI16691 Vcc power supply 2 Vo voltage out, signal wire3 Ground

33

Relay Status Board (Intensive External Terminal Board)

Part # S1655aP1Manufactured by: Sammy

Original board designed by the Three Ball Lightning Machine Factory and Sankyu Industrial Cooperative. The board was manufactured by Sankyu Electronics Corp. Distributed by Nichidenkyo The Japan Electric Game Machine Industrial Cooperative. This board was called the Intensive external terminal board. This board was designed to supply the Pachislot Parlor with information about their machines and also to provide a way for the parlor to stop any reels on any machine at any given time. The board is supplied with +24volts dc voltage and is secured by a GMA 1AMP fuse.

CN2 Header 4 pins

Pin # Description1 Ground2 Reel Stop 1 Remote Input3 Reel Stop 2 Remote Input4 Reel Stop 3 Remote Input

34

CN1 Header 30 pins to CN3 Header 16 pins CN1 pin # CN3 pin # Description (Reel Motor Control Board CN4-CN8)1 NC +24Vdc

2, 4, 27 NCGround & Signal wires for all reels home switchesRelay Motor Control BD CN4 pin2, CN6 pin 2, & CN8 pin 2

3 NC After Bonus Reset Input Line

5 NCChallenge Mode Bonus Relay Status Board +24vdc Coil of Signal Switching Relay #5 Fujitsu #SY24WK

6 NCBig Bonus Relay Status Board +24vdc Coil of Signal Switching Relay #4 Fujitsu #SY24WK .

7 NCRegular Bonus Relay Status Board +24vdc Coil of Signal Switching Relay #3 Fujitsu # SY24WK

8 NCToken Out Relay Status Board+24vdc Coil of Sensitive Signal Relay #Omron #G6E-134P

9 NCToken In Relay Status Board +24vdc Coil of Sensitive Signal Relay #Omron #G6E-134P

NC 1 Common Ground

10 2Casino Fault Monitoring Lines & Relay Motor Control BDCN3 pin 5 (voltage to Left Reel Motor) +24vdc

11 3Casino Fault Monitoring Lines & Relay Motor Control BDCN3 pin 4 (voltage to Left Reel Motor) +24vdc

12 4Casino Fault Monitoring Lines & Relay Motor Control BDCN3 pin 3 (voltage to Left Reel Motor) +24vdc

13,23 5Casino Fault Monitoring Lines & Relay Motor Control BDCN3 pin 2 (voltage to Left Reel Motor) +24vdc

14 6,11,16Casino Fault Monitoring Lines & Relay Motor Control BD CN3 Pin1, CN5 pin 1, CN7 pin1 & Power for LED D2

15 7Casino Fault Monitoring Lines & Relay Motor Control BDCN5 pin 5 (voltage to Center Reel Motor) +24vdc

16 8Casino Fault Monitoring Lines & Relay Motor Control BDCN5 pin 4 (voltage to Center Reel Motor) +24vdc

17 9Casino Fault Monitoring Lines & Relay Motor Control BDCN5 pin 3 (voltage to Center Reel Motor) +24vdc

18 10Casino Fault Monitoring Lines & Relay Motor Control BDCN5 pin 2 (voltage to Center Reel Motor) +24vdc

19 12Casino Fault Monitoring Lines & Relay Motor Control BDCN7 pin 5 (voltage to Right Reel Motor) +24vdc

20 13Casino Fault Monitoring Lines & Relay Motor Control BDCN7 pin 4 (voltage to Right Reel Motor) +24vdc

21 14Casino Fault Monitoring Lines & Relay Motor Control BDCN7 pin 3 (voltage to Right Reel Motor) +24vdc

22 15Casino Fault Monitoring Lines & Relay Motor Control BDCN7 pin 2 (voltage to Right Reel Motor) +24vdc

24Left Reel #1 Stop Control Out (Left Stop Button pressed) Ground of LED D6 (see Reel Motor Control Board CN1 pin 28)

25Center Reel #2 Stop Control Out (Center Stop Button pressed) Ground of LED D7 (see Reel Motor Control Board CN1 pin 27)

26Right Reel #3 Stop Control Out (Right Stop Button pressed) Ground of LED D8 (see Reel Motor Control Board CN1 pin 26)

28 Left Reel #1 Stop Control Input29 Center Reel #2 Stop Control Input30 Right Reel #3 Stop Control Input

35

CN4 Header 8 pin

Pin # Description1 Medals Token In Signal line monitors Medals (Tokens) inserted into machine.2 Medals Token Out Signal line monitors Medals (Tokens) paid out of this machine.3 Regular Bonus Signal line monitors when machine is in a Regular Bonus mode.4 Big Bonus Signal line monitors when machine is in a Big Bonus mode.5 CT Challenge Mode Signal line monitors when machine is in a

Challenge Bonus mode.6 Common Ground - pin 1-5. (External Ground)7 Remote Reset +24vdc - Is used to issue a reset command to the machine.8 Remote Reset Ground -24vdc - Is used to issue a reset command to the machine.

Note: pin 1-5 are output lines, pin 7-8 are Input lines

36

Skill Stop BoardPart # JSP03

Manufactured by: TAKADEN

*12vdc board has 20 - 23mA LED red or 17 - 21mA LED blue, dimensions 35 × 40 × 135 or more mm

PC1 - Photo interrupter switch Left Reel Stop SwitchPC2 - Photo interrupter switch Center Reel Stop SwitchPC3 - Photo interrupter switch Right Reel Stop SwitchD1, D3, D4 - Left Reel Stop Switch Lighting D5, D7, D8 - Left Reel Stop Switch Lighting D9, D11, D12 - Left Reel Stop Switch Lighting

CN1 Header 11 pin

Pin # Description1-11 Not Available

37

Special Chance Lighting BoardPart # SS07DC21 CMK

CN1 Header 6 pin

pin # Description1 Ground 2 Vcc power supply +28vdc light bulb LP1 light bulb3 Vcc power supply +28vdc light bulb LP2 light bulb4 Vcc power supply +28vdc light bulb LP3 light bulb5 Vcc power supply +28vdc light bulb LP4 light bulb6 Vcc power supply +28vdc light bulb LP5 light bulb

Note: Light bulb is a T10 Wedge Base 28vdc, 10w light bulb, V2 standard socket

38

Spin LeverModel # JSL

Manufactured by: TAKADEN

CN5 Header 6 pins - Start Lever Switch, & Max Bet Switch

Pin # Shinkoh Elecronics Co. LTD # KI1232Vcc Photo Interrupter 1 Brown Vcc supply power 5vdc - Start Lever Switch2 Red Ground - Start Lever Switch3 Orange Vo - Voltage out / signal wire Start Lever Switch

39

Misc. Parts List:

Cable Connector 2.5mm XH connector - JST Sales America, Inc # JST- B3B-XH-A Used on Nippon ConClux Medals (Tokens) Accepter’s - Medals Token Sensors Sharp Elect. # GP2A25Speakers - 8 Ohms, 10 WattsTransformer - Input 110VAC, 50/60HZ / Output 24VAC, 6 Amps

40

Pachislot Error Codes

ErrorCode

Meaning Solution

E-0 / C2Medals Token Acceptor is jammed.

Remove Medals Medals Token and or clean the Medals Token acceptor mechanism.

E-1 / E-2 / H-3Hopper is jammed, not functional or out of Medals Medals Tokens.

HE = Hopper Empty / HJ = Hopper is jammed.Check if the hopper is jammed, and is operational. Refill hopper with Medals Medals (Tokens)if empty.

E-4 Ram error Ram chip error or wiring loose.

E-5 Reel error Check the reels for proper operation.

E-6 Prize errorExcess Medals (Tokens) in hopper, or hopper jammed.

E-7 Hopper overloaded or Empty no Medals Medals(Tokens)present

Remove Medals Medals (Tokens) and or cleanthe Medals Token acceptor mechanism.

E-8 Hopper disconnected Check all cables to the hopper.

CE / CJMedals Token Error or Medals Token Jam

Remove Medals Medals Token and or clean the Medals Token acceptor mechanism.

CO Medals Token OverflowHopper is either jammed, not operational or excessive Medals (Tokens)in hopper.

CRMedals Token Retrograde

Medals Token or fake Medals Medals Token inserted.

EE Rom Error Rom chip error or wiring loose.HE Hopper Empty Hopper is jammed, not operational or empty.

HJ Hopper JammedHopper is either jammed, not operational or empty

HO Hopper OverloadedHopper is either jammed, not operational or excessive Medals (Tokens) in hopper.

OF Medal Token overflow Hopper is full and is overflowing in unit.RE / RR Ram Error Ram chip error or wiring loose.

* A reset is needed to clear most errors.

41

Websites:1. Japan Amusement Machinery Manufacturers Association 社団法人日本アミューズメントマシン工業協会, Shadanhōjin Nihon Amusement Machine Kōgyōkyōkai, more simply known by the acronym JAMMA, is a group of Japanese companies in a Partnership-profit working in the sector video arcade and founded in early 1980 game.

2. Japan Amusement Park Equipment Association JAPEA

3. New reader/writer for the CPU LE 2080A-PA

4. Pachinko Pachislott Security Information Organization

5. National Public Safety Commission NPSC of Japan - is the designated testing organization, and Authority over Gaming machines.Look under guide for Electronic Submission, etc. linkItem iv twelve days National Public Safety Commission's rules six February 10, 1955 rules for test etc. and types of certification of the gaming machine.

6. Prefectural Public Safety Commission List PPSC - designated examining agency responsible for the “type test” consignment of specifications of the gaming machine

7. General Safety Foundation Press Association - designated testing laboratories"Designated Testing Laboratories", the Security Electronics and Communications Technology Association, Prefectural Public Safety Commission PPSC but we do the gaming machine "type test" in response to the commission of the meeting.

8. Nihon Dendo-shiki Yugiki Tokkyo Kabushiki Kaisha NDT - Japan electric game machine patent Ltd. Nichiden patent. The company handles disputes in machine patents, does patent checks, and handles patent-related issues and paperwork for Pachilsot manufacturing companies.

9. Japan Patent Office

42