Upload
others
View
9
Download
0
Embed Size (px)
Citation preview
Workshop ManualWiring diagrams
61, 62, 63, 71, 72, 73, 74-series
D
2(0)
Group 30 Electrical system
Wiring diagrams
Marine enginesTAMD61A • TAMD62A
TAMD63L-A • TAMD63P-ATAMD71A • TAMD71B
TAMD72A • TAMD72P-A • TAMD72WJ-ATAMD73P-A • TAMD73WJ-ATAMD74A-A • TAMD74A-B
TAMD74C-A • TAMD74L-A • TAMD74P-ATAMD74C-B • TAMD74L-B • TAMD74P-B
ContentsSafety information ............................................... 2
Introduction ......................................................... 2Important ............................................................ 2
General information ............................................ 5About the workshop manual ............................... 5Spare parts ......................................................... 5Certified engines ................................................. 5
Wiring diagrams, engine ..................................... 6TAMD61A, TAMD71A (12V, 24V) ...................... 7TAMD61A, TAMD62A,TAMD71A, TAMD71B,TAMD72A, TAMD72WJ–A (12V, 24V) ............... 8TAMD63L-A, TAMD63P-A (12V, 24V) ............... 9TAMD71B (12V, 24V) ........................................ 10TAMD72WJ-A (12V, 24V) .................................. 11TAMD72P-A (12V) ............................................. 12TAMD72P-A (24V) ............................................. 13TAMD73P-A (12V) ............................................. 14TAMD73P-A (24V) ............................................. 15TAMD73WJ-A, TAMD74A-A/A-B (12V, 24V) ..... 16
TAMD74C-A/L-A/P-A (12V) ............................... 17TAMD74C-B/L-B/P-B (12V) ............................... 18TAMD74C-A/L-A/P-A/C-B/L-B/P-B (24V) ........... 19Block diagram – Instrument panels .................... 20Wiring diagram – instrument panel, maincontrol position ................................................... 22Wiring diagrams – instrument panel foralternative control position (flying bridge) andauxiliary control panel ......................................... 24Wiring diagram – instrument kit, main controlposition ............................................................... 26Wiring diagram – instrument kit for alternativecontrol position (flying bridge) ............................. 28Wiring diagrams – control system (EDC) ............ 30Wiring diagrams – general .................................. 37Wiring diagram – EDC colour coding. ................. 38Wiring diagrams – alternative control systemfor EDC controls ................................................. 40Wiring diagram – water jet control panel ............. 44Reversing bucket operation – water jet ............... 46
References to Service Bulletins ......................... 48
2
Safety information
IntroductionThe workshop manual contains technical data, de-scriptions and repair instructions for products or prod-uct versions noted in the table of contents, suppliedby Volvo Penta. Make sure you use the correct work-shop literature.
Read the available safety information, “General infor-mation” and “Repair instructions” in the workshopmanual before you start to do any service work.
Important
The following special warning signs are found in theworkshop manual and on the product.
WARNING! Warns for the risk of personal inju-ry, major damage to product or property, or se-rious malfunctions if the instruction is ignored.
IMPORTANT! Is used to call attention to thingswhich could cause damage or malfunctions toproduct or property.
NOTE! Is used to call attention to important informa-tion, to facilitate work processes or operation.
To give you a perspective on the risks which alwaysneed to be observed and precautions which alwayshave to be taken, we have noted them below.
Make it impossible to start the engine by cuttingsystem current with the main switch(es) andlock it (them) in the off position before startingservice work. Fix a warning sign by the helms-man’s seat.
All service work should normally be done on astationary engine. Some work, such as adjust-ments, need the engine to be running, however.Going close to a running engine is a safety risk.Remember that loose clothes, long hair etc. cancatch on rotating components and cause se-vere injury.
If work is done adjacent to a running engine, acareless movement or a dropped tool can leadto personal injury in the worst case. Be carefulwith hot surfaces (exhaust pipes, turbos, chargeair pipes, starting heaters etc.) and hot fluids inpipes and hoses on an engine which is runningor which has just stopped. Re-install all guardswhich have been removed during service work,before re-starting the engine.
Make sure that the warning or information la-bels on the product are always clearly visible.Replace labels which have been damaged orpainted over.
Never start an engine without the air filter inplace. The rotating compressor turbine in theturbocharger can cause severe injury. Foreignbodies in the inlet pipe can also cause severemechanical damage.
Never use start spray or similar products as astarting aid. Explosions could occur in the inletmanifold. Danger of personal injury.
Avoid opening the coolant filling cap when theengine is hot. Steam or hot coolant can sprayout at the same time as the pressure which hasbuilt up is lost. Open the filler cap slowly, andrelease the pressure in the cooling system if thefilling cap or tap has to be opened, or if a plugor coolant hose has to be removed when theengine is hot. Steam or hot coolant can streamout in an unexpected direction.
Hot oil can cause burns. Avoid skin contact withhot oil. Make sure that the oil system is de-pres-surised before doing any work on it. Never startor run the engine with the oil filler cap removed,because of the risk of oil spillage.
Stop the engine and close the sea cocks beforedoing any work on the cooling system.
Only start the engine in a well-ventilated area.When operated in a confined space, exhaustfumes and crankcase gases must be ventilatedfrom the engine bay or workshop area.
Always use goggles when doing any workwhere there is any risk of splinters, grindingsparks, acid splash or other chemicals. Youreyes are extremely sensitive, injury could causeblindness!
3
Safety information
Avoid skin contact with oil! Long-term or repeat-ed skin contact with oil can make your skin dryout. The consequence is irritation, dry skin, ec-zema and other skin disorders. Used oil is morehazardous to health than new oil. Use protec-tive gloves and avoid oil-soaked clothes andrags. Wash regularly, especially before meals.Use special skin cream to avoid drying and fa-cilitate skin cleaning.
Most chemicals intended for the product (e.g.engine and transmission oils, glycol, petrol(gasoline) and diesel oil) or chemicals for work-shop use (e.g. degreasers, paints and solvents)are hazardous. Read the instruction on thepackages carefully! Always observe the safetyadvice (e.g. use of breathing protection, gog-gles, gloves etc.). Make sure that other person-nel are not inadvertently exposed to hazardoussubstances, such as via the air they breathe.Ensure good ventilation. Handle used and sur-plus chemicals in the prescribed manner.
Be very careful when searching for leaks in thefuel system and testing fuel injectors. Use gog-gles. The jet which comes from a fuel injectorhas very high pressure and considerable pene-tration ability. Fuel can force its way deep intobody tissue and cause severe injury. Risk ofblood poisoning (septicaemia).
All fuels, and many chemicals, are flammable.Make sure that open flames or sparks can notset them alight. Petrol (gasoline), some thinnersand hydrogen gas from batteries are extremelyflammable and explosive when mixed with air inthe correct ratio. Do not smoke! Provide goodventilation and take the necessary precautionsbefore you start welding or grinding in the vicini-ty. Always have a fire extinguisher easily avail-able near the workplace.
Make sure that oil and fuel soaked rags, andused fuel and oil filters are stored in a safeplace. Oil soaked rags can self-ignite in certaincircumstances. Used fuel and oil filters are pol-luting waste and must be handed to an ap-proved waste management facility for destruc-tion, together with used lubrication oil, contami-nated fuel, paint residue, solvents, degreasersand wash residue.
Batteries must never be exposed to openflames or electric sparks. Do not smoke close tothe batteries. The batteries generate hydrogengas when charged, which forms an explosivegas when mixed with air. This gas is very flam-mable and highly explosive. A spark, which can
be formed if the batteries are wrongly connect-ed, is enough to make a battery explode andcause damage. Do not move the connectionwhen you attempt to start the engine (risk ofarcing), and do not stand and lean over one ofthe batteries.
Never mix up the battery positive and negativepoles when the batteries are installed. If the bat-teries are wrongly connected, this can causesevere damage to the electrical equipment.Please check the wiring diagram!
Always use goggles when charging and han-dling batteries. Battery electrolyte contains high-ly corrosive sulphuric acid. If this comes intocontact with your skin, wash at once with soapand a lot of water. If you get battery acid in youreyes, flush at once with a generous amount ofwater, and get medical assistance at once.
Stop the engine and cut the system current withthe main switch(es) before doing any work onthe electrical system.
The clutch must be adjusted with the engineshut off.
The existing lugs on the engine/reverse gearshould be used for lifting. Always check that thelifting devices are in good condition and thatthey have the correct capacity for the lift (theweight of the engine plus the reverse gear andextra equipment if installed).The engine should be lifted with a customisedor adjustable lifting boom for safe handling andto avoid damaging components on top of theengine. All chains or cables should be parallelto each other and should be as square as pos-sible to the top of the engine.If other equipment connected to the engine hasaltered its centre of gravity, special lifting devic-es may be needed to obtain the correct balanceand safe handling.Never do any work on an engine which justhangs from a lifting device.
Never work alone when heavy components areto be dismantled, even when safe lifting devicessuch as lockable blocks & tackle are used.Even when lifting devices are used, two peopleare needed in most cases. One who operatesthe lifting device and other who makes sure thatcomponents move freely and are not damagedduring lifting.When you work aboard a boat, always makesure that there is enough space for disassemblywhere you are working, with no risk for personalor material damage.
4
Safety information
Components in the electrical and fuel systemson Volvo Penta products have been designedto minimise the risks of explosion and fire. Theengine must not be operated in environmentswith adjacent explosive media.
Remember the following when washing with ahigh pressure washer: Never aim the water jetat seals, rubber hoses or electrical components.Never use a high pressure washer for enginecleaning.
Only use the fuels recommended by Volvo Pen-ta. Please refer to the instruction book. The useof fuel of inferior quality can damage the en-gine. In a diesel engine, poor fuel can cause theregulation rod to bind and the engine will over-rev, entailing a strong risk of personal injury andmachinery damage. Poor fuel can also lead tohigher maintenance costs.
© 2000 AB VOLVO PENTAWe reserve the right to make design changes and amendments without prior notice.
Printed on environmentally compatible paper.
WARNING! Fuel delivery pipes must not bebent or straightened under any circumstances.Damaged pipes must be replaced.
5
General information
About the workshop manualThis workshop contains the wiring diagrams for thestandard versions of engines TAMD61A, TAMD62A,TAMD63L-A, TAMD63P-A, TAMD71A, TAMD71B,TAMD72A, TAMD72P-A, TAMD72WJ-A,TAMD73P-A, TAMD73WJ-A, TAMD74A-A,TAMD74A-B, TAMD74C-A, TAMD74L-A,TAMD74P-A, TAMD74C-B, TAMD74L-B,TAMD74P-B.
The engine designation and number are noted on thenumber plate. The engine designation and numbermust always be given in all correspondence about anengine.
The workshop manual has been primarily preparedfor Volvo Penta service workshops and their qualifiedpersonnel. This assumes that people who use theManual have basic knowledge of marine drive sys-tems and can do the tasks of a mechanical or electri-cal nature associated with the trade. Volvo Pentaconstantly improves its products, so we reserve theright to make modifications without prior notification.All information in this manual is based on productdata which was available up to the date on which themanual was printed. Any material changes introducedinto the product or service methods after this date arenotified by means of Service Bulletins.
Spare partsSpare parts for electrical and fuel systems are subjectto various national safety requirements. Volvo PentaOriginal Spares comply with these requirements. Nodamage whatever, occasioned by use of non-originalVolvo Penta spares for the product, will be compen-sated by the warranty offered by Volvo Penta.
Certified enginesWhen service or repairs are done to an emissioncertified engine, which is used in an area whereexhaust emissions are regulated by law, it is im-portant to be aware of the following:
Certification means that an engine type has beenchecked and approved by the relevant authority. Theengine manufacturer guarantees that all enginesmade of the same type are equivalent to the certifiedengine.
This put special demands on service and repairwork, as follows:
l Maintenance and service intervals recommendedby Volvo Penta must be complied with.
l Only Volvo Penta original spares may be used.
l Service to injection pumps, pump settings and in-jectors must always be done by an authorisedVolvo Penta workshop.
l The engine must not be converted or modified,except for the accessories and service kits whichVolvo Penta has approved for the engine.
l Installation changes to the exhaust pipe and en-gine air inlet ducts must not be done.
l No seals may be broken by unauthorised person-nel.
The general advice in the instruction book about op-eration, care and maintenance applies.
IMPORTANT! Delayed or inferior care/mainte-nance, and the use of non-original spares,mean that AB Volvo Penta can no longer be re-sponsible for guaranteeing that the engine com-plies with the certified version.
Damage, injury and/or costs which arise fromthis will not be compensated by Volvo Penta.
6
Wiring diagrams – engines
Wiring diagrams
7
1. Batteries (12V, 24V)2. Main switch3. Starting heater4. High power relay5. Starter motor6. Alternator7. Stop solenoid8. Circuit breaker, 8A (+)
9. Circuit breaker, 8A (–)10. Engine speed sensor11. Oil pressure sensor, reverse gear12. Oil pressure monitor, engine13. Oil pressure sensor, engine14. Pressure sensor, charge pressure15. Coolant temperature monitor16. Coolant temperature sensor
17. Starter relay18. Fuse 8A (24V), and 16A (12V)19. Timer relay20. Stop relay21. Earthing point22. Connector, instrument panel23. Earth cable
Cable colourBL = Blue P = PinkLBL = Light blue PU = PurpleBN = Brown R = RedLBN = Light brown SB = BlackGN = Green VO = VioletGR = Grey W = WhiteOR = Orange Y = Yellow
Cable areas (mm²) are specified after thecolour code in wiring diagrams.
Unspecified areas = 1.0 mm².
A broken line indicates a non Volvo Pentacable.
Engines: TAMD61A*, TAMD71A* (12V, 24V)* Up to engine No. 1101021541/xxxx.
Wiring diagrams
8
1. Batteries (12V, 24V)2. Main switch3. Starting heater4. High power relay5. Starter motor6. Alternator7. Stop solenoid8. Circuit breaker, 8A (+)9. Circuit breaker, 8A (–)
10. Engine speed sensor11. Oil pressure sensor, reverse
gear12. Oil pressure monitor, engine13. Oil pressure sensor, engine14. Pressure sensor, charge pres-
sure15. Coolant temperature monitor16. Coolant temperature sensor
17. Starter relay18. Fuse 8A (24V), and 16A (12V)19. Timer relay20. Stop relay21. Earthing point22. Connector, instrument panel23. Earth cable24. Fuse (150A)
Engines: TAMD61A*, TAMD62A, TAMD71A*, TAMD71B**, TAMD72A,TAMD72WJ-A** (12V, 24V)* As from. engine No. 1101021542/xxxx.
** Up to engine No. 207181083/xxxx.
Cable colourBL = Blue P = PinkLBL = Light blue PU = PurpleBN = Brown R = RedLBN = Light brown SB = BlackGN = Green VO = VioletGR = Grey W = WhiteOR = Orange Y = Yellow
Cable areas (mm²) are specified after thecolour code in wiring diagrams.
Unspecified areas = 1.0 mm².
A broken line indicates a non Volvo Pentacable.
Wiring diagrams
9
Engines: TAMD63L-A, TAMD63P-A (12V, 24V)
1. Batteries (12V, 24V)2. Main switch3. Starter motor4. Alternator5. Starter relay6. Circuit breakers (8A)7. Oil pressure sensor, reverse gear
(0–30 bar/0–435 psi)8. Pressure sensor, charge pressure
(0–3 bar/0–43.5 psi)
9. Fuel shut-off valve10. Coolant temperature monitor (97°C/207°F, normally open –
closes if fault occurs)11. Coolant temperature sensor (40–120°C/104–248°F)12. Oil pressure monitor, engine (0.7 bar/10 psi, normally open
– closes if fault occurs)13. Oil pressure sensor, engine (0–10 bar/0–145 psi)14. Engine speed sensor15. Connector, instrument panel
Cable colourBL = Blue P = PinkLBL = Light blue PU = PurpleBN = Brown R = RedLBN = Light brown SB = BlackGN = Green VO = VioletGR = Grey W = WhiteOR = Orange Y = Yellow
Cable areas (mm²) are specified after thecolour code in wiring diagrams.
Unspecified areas = 1.0 mm².
A broken line indicates a non Volvo Pentacable.
Wiring diagrams
10
Engines: TAMD71B* (12V, 24V)* As from. engine No. 207181084/xxxx.
1. Batteries (12V, 24V)2. Main switch3. Starter motor4. Alternator5. Fuel shut-off valve6. Fuse (8A)
7a. Stop relay7b. Starter relay
8. Circuit breakers (8A)9. Earthing point
10. Timer relay11. Fuse (150A)12. Starting heater13. Oil pressure sensor, reverse gear14. Pressure sensor, charge pressure15. Oil pressure sensor, engine
16. Oil pressure monitor, engine17. Coolant temperature sensor18. Coolant temperature monitor19. Engine speed sensor20. Connector, instrument panel
Cable colourBL = Blue P = PinkLBL = Light blue PU = PurpleBN = Brown R = RedLBN = Light brown SB = BlackGN = Green VO = VioletGR = Grey W = WhiteOR = Orange Y = Yellow
Cable areas (mm²) are specified after thecolour code in wiring diagrams.
Unspecified areas = 1.0 mm².
A broken line indicates a non Volvo Pentacable.
Wiring diagrams
11
Engines: TAMD72WJ-A* (12V, 24V)* As from. engine No. 207181084/xxxx.
1. Batteries (12V, 24V)2. Main switch3. Starter motor4. Alternator5. Fuel shut-off valve6. Fuse
7. Stop relay8. Starter relay9. Circuit breakers (8A)
10. Earthing point11. Connector12. Engine speed sensor
13. Coolant temperature monitor14. Coolant temperature sensor15. Oil pressure monitor, engine16. Oil pressure sensor, engine17. Pressure sensor, charge pressure18. Oil pressure sensor, reverse gear
Cable colourBL = Blue P = PinkLBL = Light blue PU = PurpleBN = Brown R = RedLBN = Light brown SB = BlackGN = Green VO = VioletGR = Grey W = WhiteOR = Orange Y = Yellow
Cable areas (mm²) are specified after thecolour code in wiring diagrams.
Unspecified areas = 1.0 mm².
A broken line indicates a non Volvo Pentacable.
Wiring diagrams
12
Engine: TAMD72P-A (12V)
1. Batteries (12V)2. Main switch3. Connector4. Starter motor5. Alternator6. Starter relay7. Main relay8. Pressure sensor reverse gear9. Pressure sensor turbo
10. Pressure monitor oil11. Oil pressure sensor12. Coolant temperature sensor13. Circuit breakers (8A)14. Stop relay15. Connector instrument panel16. Connector controls17. Connector diagnostic connector18. Control unit19. Temperature sensor charge air
20. Temperature sensor coolant21. Position sensor, control rod22. Engine speed sensor23. Control solenoid EDC24. Connector reverse gear25. Shift solenoid, reverse gear26. Injection pump
Cable colourBL = Blue P = PinkLBL = Light blue PU = PurpleBN = Brown R = RedLBN = Light brown SB = BlackGN = Green VO = VioletGR = Grey W = WhiteOR = Orange Y = Yellow
Cable areas (mm²) are specified after thecolour code in wiring diagrams.
Unspecified areas = 1.0 mm².
A broken line indicates a non Volvo Pentacable.
Wiring diagrams
13
Engine: TAMD72P-A (24V)
1. Batteries (24V)2. Main switch3. Starter motor4. Alternator5. Starter relay6. Main relay7. Stop relay8. Circuit breakers (8A)9. Pressure sensor reverse gear
10. Pressure sensor turbo11. Pressure monitor oil12. Oil pressure sensor13. Coolant temperature sensor14. Connector instrument panel15. Connector controls16. Connector diagnostic connector17. Control unit18. Temperature sensor charge air
19. Temperature sensor coolant20. Position sensor, control rod21. Engine speed sensor22. Control solenoid EDC23. Connector reverse gear24. Shift solenoid, reverse gear25. Injection pump
Cable colourBL = Blue P = PinkLBL = Light blue PU = PurpleBN = Brown R = RedLBN = Light brown SB = BlackGN = Green VO = VioletGR = Grey W = WhiteOR = Orange Y = Yellow
Cable areas (mm²) are specified after thecolour code in wiring diagrams.
Unspecified areas = 1.0 mm².
A broken line indicates a non Volvo Pentacable.
Wiring diagrams
14
Engine: TAMD73P-A (12V)
1. Batteries (12V)2. Main switch3. Connector battery4. Starter motor5. Alternator6. Starter relay7. Main relay8. Pressure sensor reverse gear9. Pressure sensor turbo
10. Pressure monitor oil11. Oil pressure sensor12. Temperature sensor coolant13. Circuit breakers (8A)14. Stop relay15. Connector instrument panel16. Connector controls17. Connector diagnostic connector18. Control unit
19. Temperature sensor chargeair
20. Temperature sensor coolant21. Position sensor, control rod22. Engine speed sensor23. Control solenoid EDC24. Connector reverse gear25. Shift solenoid, reverse gear26. Injection pump
Cable colourBL = Blue P = PinkLBL = Light blue PU = PurpleBN = Brown R = RedLBN = Light brown SB = BlackGN = Green VO = VioletGR = Grey W = WhiteOR = Orange Y = Yellow
Cable areas (mm²) are specified after thecolour code in wiring diagrams.
Unspecified areas = 1.0 mm².
A broken line indicates a non Volvo Pentacable.
Wiring diagrams
15
Engine: TAMD73P-A (24V)
1. Batteries (24V)2. Main switch3. Starter motor4. Alternator5. Starter relay6. Main relay7. Pressure sensor reverse gear8. Pressure sensor turbo9. Pressure monitor oil
10. Pressure sensor oil11. Temperature sensor coolant12. Circuit breakers (8A)13. Stop relay14. Connector instrument panel15. Connector controls16. Connector diagnostic connector17. Control unit18. Temperature sensor charge air
19. Temperature sensor coolant, EDC20. Position sensor, control rod21. Engine speed sensor22. Control solenoid EDC23. Connector reverse gear24. Shift solenoid, reverse gear25. Injection pump
Cable colourBL = Blue P = PinkLBL = Light blue PU = PurpleBN = Brown R = RedLBN = Light brown SB = BlackGN = Green VO = VioletGR = Grey W = WhiteOR = Orange Y = Yellow
Cable areas (mm²) are specified after thecolour code in wiring diagrams.
Unspecified areas = 1.0 mm².
A broken line indicates a non Volvo Pentacable.
Wiring diagrams
16
Engines: TAMD73WJ-A, TAMD74A-A, TAMD74A-B (12V, 24V)
1. Batteries (12V, 24V)2. Main switch3. Starter motor4. Alternator5. Starter relay6. Fuel shut-off valve7. Coolant temperature monitor8. Oil pressure sensor, reverse gear
9. Pressure sensor, charge pressure10. Oil pressure monitor, engine11. Oil pressure sensor, engine12. Coolant temperature sensor13. Engine speed sensor14. Circuit breakers (8A)15. Connector, instrument panel
Cable colourBL = Blue P = PinkLBL = Light blue PU = PurpleBN = Brown R = RedLBN = Light brown SB = BlackGN = Green VO = VioletGR = Grey W = WhiteOR = Orange Y = Yellow
Cable areas (mm²) are specified after thecolour code in wiring diagrams.
Unspecified areas = 1.0 mm².
A broken line indicates a non Volvo Pentacable.
Wiring diagrams
17
Engines: TAMD74C-A, TAMD74L-A, TAMD74P-A (12V)
1. Batteries (12V)2. Main switch3. Connector, battery4. Starter motor5. Alternator6. Fuse (7.5A)7. Starter relay8. Main relay9. Stop relay
10. Circuit breakers (8A)11. Oil pressure sensor, reverse gear12. Pressure sensor, charge pressure13. Oil pressure monitor, engine14. Oil pressure sensor, engine15. Coolant temperature sensor16. Connector, instrument panel17. Connector, controls18. Connector, diagnostic connector
19. Control unit EDC20. Temperature sensor, charge air21. Coolant temperature sensor EDC22. Position sensor, control rod23. Engine speed sensor24. Control solenoid EDC25. Connector, reverse gear26. Solenoid, reverse gear27. Injection pump
Cable colourBL = Blue P = PinkLBL = Light blue PU = PurpleBN = Brown R = RedLBN = Light brown SB = BlackGN = Green VO = VioletGR = Grey W = WhiteOR = Orange Y = Yellow
Cable areas (mm²) are specified after thecolour code in wiring diagrams.
Unspecified areas = 1.0 mm².
A broken line indicates a non Volvo Pentacable.
Wiring diagrams
18
Engines: TAMD74C-B, TAMD74L-B, TAMD74P-B (12V)
1A. Batteries (12V)1B. Emergency/extra batteries2A. Main switch2B. Main switch for emergency/extra bat-
teries3. Alternator4. Starter motor5. Starter relay6. Main relay7. Control unit EDC8. Stop relay
9. Circuit breakers (8A)10. Oil pressure sensor, reverse gear11. Pressure sensor, charge pressure12. Oil pressure monitor, engine13. Oil pressure sensor, engine14. Coolant temperature sensor15. Joint16. Connector, instrument panel17. Connector, reverse gear18. Solenoid, reverse gear19. Temperature sensor, charge air
20. Coolant temperature sensor EDC21. Position sensor, control rod22. Engine speed sensor23. Control solenoid EDC24. Connector, diagnostic connector25. Connector, controls (male)26. Connector, controls (female)27. Fuse (7.5A)28. Voltage converter
Cable colourBL = Blue P = PinkLBL = Light blue PU = PurpleBN = Brown R = RedLBN = Light brown SB = BlackGN = Green VO = VioletGR = Grey W = WhiteOR = Orange Y = Yellow
Cable areas (mm²) are specified after thecolour code in wiring diagrams.
Unspecified areas = 1.0 mm².
A broken line indicates a non Volvo Pentacable.
Wiring diagrams
19
Engines: TAMD74C-A/B, TAMD74L-A/B, TAMD74P-A/B (24V)
1. Batteries (24V)2. Main switch3. Starter motor4. Alternator5. Starter relay6. Main relay7. Fuse (7.5A)8. Oil pressure sensor, reverse gear9. Pressure sensor, charge pressure
10. Oil pressure monitor, engine11. Oil pressure sensor, engine12. Coolant temperature sensor13. Circuit breaker (8A)14. Stop relay15. Connector, instrument panel16. Connector, controls17. Connector, diagnostic connector18. Control unit EDC
19. Temperature sensor, charge air20. Coolant temperature sensor EDC21. Position sensor, control rod22. Engine speed sensor23. Control solenoid EDC24. Connector, reverse gear25. Solenoid, reverse gear26. Injection pump
Cable colourBL = Blue P = PinkLBL = Light blue PU = PurpleBN = Brown R = RedLBN = Light brown SB = BlackGN = Green VO = VioletGR = Grey W = WhiteOR = Orange Y = Yellow
Cable areas (mm²) are specified after thecolour code in wiring diagrams.
Unspecified areas = 1.0 mm².
A broken line indicates a non Volvo Pentacable.
20
Block diagram – instrument panels
Wiring diagrams
21
A. Main panelB. Auxiliary panelC. Panel for alternative controls (flying bridge)*
* Note. Main panel (A) can also be found on alternative controls.
D. Alarm board. (Only used when main panel ”A” is not found)E. Branch connectionF. Junction box** with fuses
** Note. Illustration shows TAMD63, TAMD73 and TAMD74.
22
Wiring diagram – instrument panel, main controlposition
Wiring diagrams
23
Spring loaded
1. Instrument lighting2. Voltmeter3. Oil pressure gauge4. Coolant temperature gauge5. Connector for connection of extra warning
display (optional)6. Alarm unit7. Warning lamp, coolant temperature8. Warning lamp, oil pressure9. Warning lamp, charge
10. Warning lamp, pre-heating*11. Switch, Instrument lighting12. Switch – Alarm test/Acknowledge13. Tachometer with built-in hours counter14. Key switch15. Alarm16. Joining piece17. Connector CPC 16-pin18. Connector, turbo/reverse gear
* TAMD61, -62, TAMD71, TAMD72A, -WJ.
Instrument panel, main control position: TAMD61A, TAMD62A, TAMD63L-A,TAMD63P-A, TAMD71A, TAMD71B, TAMD72A, TAMD72WJ-A, TAMD72P-A,TAMD73P-A, TAMD73WJ-A, TAMD74A-A, TAMD74A-B, TAMD74C-A/B,TAMD74L-A/B, TAMD74P-A/B
Cable colourBL = Blue P = PinkLBL = Light blue R = RedBN = Brown SB = BlackLBN = Light brown VO = VioletGN = Green W = WhiteGR = Grey Y = YellowOR = Orange
Not specified cable areas = 1.0 mm²
Spring loaded
24
Wiring diagrams – instrument panel, alternativecontrol position (flying bridge)and auxiliary panel
Wiring diagrams
25
Instrument panel, alternative control position (flying bridge) and auxiliarypanel: TAMD61A, TAMD62A, TAMD63L-A, TAMD63P-A, TAMD71A,TAMD71B, TAMD72A, TAMD72WJ-A, TAMD72P-A, TAMD73P-A,TAMD73WJ-A, TAMD74A-A, TAMD74A-B, TAMD74C-A/B, TAMD74L-A/B,TAMD74P-A/B
1. Instrument lighting5. Connector, connection of extra warn-
ing display (optional)6. Electronic unit, alarm7. Warning lamp, coolant temperature8. Warning lamp, oil pressure9. Warning lamp, charge
10. Indication lamp, pre-heating*11. Switch, Instrument lighting12. Switch, Alarm test/Acknowledge13. Tachometer with built-in hours
counter
* TAMD61, -62, TAMD71, TAMD72A, -WJ.
14. Key switch15. Alarm16. Joining piece17. Connector CPC, 16-pin18. Oil pressure gauge, reverse gear19. Gauge for turbo charge pressure20. Connection to instrument lighting on main
panel21. Connection to circuit board on main panel22. Connection to connector (18) on main panel
Cable colourBL = Blue P = PinkLBL = Light blue PU = PurpleBN = Brown R = RedLBN = Light brown SB = BlackGN = Green VO = VioletGR = Grey W = WhiteOR = Orange Y = Yellow
Cable areas (mm²) are specified after thecolour code in wiring diagrams. Unspeci-fied areas = 1.0 mm².
A broken line indicates a non Volvo Pentacable.
Spring loaded
Spring loaded
26
Wiring diagram – instrument kit main controlposition
Wiring diagrams
27
Instrument kit, main control position: TAMD61A, TAMD62A, TAMD63L-A,TAMD63P-A, TAMD71A, TAMD71B, TAMD72A, TAMD72WJ-A, TAMD72P-A,TAMD73P-A, TAMD73WJ-A, TAMD74A-A, TAMD74A-B, TAMD74C-A/B,TAMD74L-A/B, TAMD74P-A/B
1. Key switch2. Switch – Alarm test3. Switch – Instrument lighting4. Alarm5. Electronic unit, alarm6. Coolant temperature gauge7. Oil pressure gauge, engine8. Voltmeter9. Pressure gauge, charge pressure
10. Oil pressure gauge, reverse gear11. Tachometer with built-in hours
counter12. Instrument lighting13. Joint14. Joining piece15. Connector CPC, 16-pin16. Connector for connection of extra
warning display (optional)
Cable colourBL = Blue P = PinkLBL = Light blue PU = PurpleBN = Brown R = RedLBN = Light brown SB = BlackGN = Green VO = VioletGR = Grey W = WhiteOR = Orange Y = Yellow
Cable areas (mm²) are specified after thecolour code in wiring diagrams. Unspeci-fied areas = 1.0 mm².
A broken line indicates a non Volvo Pentacable.
28
Wiring diagram – instrument kit alternativecontrol position (flying bridge)
Wiring diagrams
29
Instrument kit, alternative control position (flying bridge): TAMD61A,TAMD62A, TAMD63L-A, TAMD63P-A, TAMD71A, TAMD71B, TAMD72A,TAMD72WJ-A, TAMD72P-A, TAMD73P-A, TAMD73WJ-A, TAMD74A-A,TAMD74A-B, TAMD74C-A/B, TAMD74L-A/B, TAMD74P-A/B
1. Electronic unit (alarm)2. Connector for connection of extra
warning display (optional)3. Warning lamp, coolant tempera-
ture4. Warning lamp, oil pressure5. Warning lamp, charge
6. Indication lamp, pre-heating(TAMD71B)
7. Alarm8. Switch–Alarm test/Acknowledge9. Switch, Instrument lighting
10. Connection point (not dismountable)11. Instrument lighting
12. Tachometer with built-in hours counter13. Start button14. Stop button15. Connector for connection of possible
neutral position switch (optional)16. 16-pin connection
Cable colourBL = Blue P = PinkLBL = Light blue PU = PurpleBN = Brown R = RedLBN = Light brown SB = BlackGN = Green VO = VioletGR = Grey W = WhiteOR = Orange Y = Yellow
Cable areas in mm² are specified after thecolour code in the wiring diagrams.
When no area is specified, 1.0 mm² isapplicable.
A broken line indicates a non Volvo Pentacable.
30
Wiring diagrams – control system (EDC)
ACTIVESTATION
DIAGNOSIS DIAGNOSIS
NEUTRAL SYNC NEUTRAL
NEUTRAL DIAGNOSIS
ACTIVESTATION
NEUTRAL DIAGNOSIS
Wiring diagrams
31
Control system, EDC: TAMD72P-A, TAMD73P-A
Single control position – single levercontrols (single engine installation)
Multiple control positions – single levercontrols (single engine installation)
Cable colourBL = BlueBN = BrownGN = GreenOR = OrangeP = PinkR = RedSB = BlackW = WhiteY = Yellow
Cable areas = 0.75 mm²
VP controls:Late model NEUTRAL
Old model NEUTRAL
Single control position – twin levercontrols (single engine installation)
Multiple control positions – twin levercontrols (single engine installation)
Position schedule(all wiring diagrams)
1. Indication lamp2. 1-pin switch3. Neutral position switch4. Connector5. Potentiometer6. 16-pin connection7. 2-pin connection (diagnostic connector)8. Joint
Wiring diagrams
32
Control system, EDC: TAMD72P-A, TAMD73P-A
Single lever controls (twin engine installation)
Twin lever controls (twin engine installation)
Cable colourBL = BlueBN = BrownGN = GreenOR = OrangeP = PinkR = RedSB = BlackW = WhiteY = Yellow
Cable areas = 0.75 mm²
VP controls:Late model NEUTRAL
Old model NEUTRAL
Position schedule(both wiring diagrams)
1. Indication lamp2. Switch3. Connector4. Relay5. Neutral position switch6. Potentiometer7. Connector, Port – Starboard cable kit8. 2-pin connection (diagnostic connector)9. 16-pin connection, Port engine
10. 16-pin connection, Starboard engine
Wiring diagrams
33
Control system, EDC: TAMD73P-A*, TAMD74* Late model
Single engine installation.Single lever controls.
Cable colourBL = BlueBN = BrownGN = GreenOR = OrangeP = PinkR = RedSB = BlackW = WhiteY = Yellow
Cable areas = 0.75 mm²
Single engine installation.Twin lever controls.
Position schedule (both wiring diagrams)
1. Press switch with Indication lamp, ”Neutral” – green2. Press switch with Indication lamp, ”Diagnosis” – yellow3. Press switch with Indication lamp, ”Active station” – red4. Connector5. Potentiometer, throttle opening/gear shift
5a. Potentiometer, throttle opening5b. Potentiometer, gear shift6. Neutral position switch (only mechanically operated reverse
gear)7. 8-pin connection (male)8. 8-pin connection (female)9. Joint
Wiring diagrams
34
Control system, EDC: TAMD73P-A*, TAMD74* Late model
Twin engine installation. Single lever controls.
Twin engine installation. Twin lever controls.
Cable colourBL = BlueBN = BrownGN = GreenOR = OrangeP = PinkR = RedSB = BlackW = WhiteY = Yellow
Cable areas = 0.75 mm²
Position schedule(both wiring diagrams)
1. Press switch with Indication lamp,”Neutral” – green
2. Press switch with Indication lamp,”Diagnosis” – yellow
3. Press switch with Indication lamp,”Active station” – red
4. Press switch with Indication lamp,”Sync” – blue
5. Press switch with Indication lamp,”Neutral” – green
6. Press switch with Indication lamp,”Diagnosis” – yellow
7. Connector8. Connector, Port – Starboard cable kit9. Relay
10. Potentiometer, throttle opening/gear shift10a. Potentiometer, throttle opening10b. Potentiometer, gear shift11. 8-pin connection (male) – Port engine12. 8-pin connection (female) – Starboard
engine13. Neutral position switch (only mechanically
operated reverse gear)
Wiring diagrams
35
Control system, EDC: TAMD74
Single engine installation.Single lever controls.
Cable colourBL = BlueBN = BrownGN = GreenOR = OrangeP = PinkR = RedSB = BlackW = WhiteY = Yellow
Cable areas = 0.75 mm² unless otherwisespecified.
Single engine installation.Twin lever controls.
Position schedule (both wiring diagrams)
1. Control panel2. Connector3. Diagnostic button
3a. LED (yellow)4. Operating button
4a. LED (red)5. Neutral button
5a. LED (green)6. LED for background illumination7. 8-pin moisture-proof connector (male)8. 8-pin moisture-proof connector (female)9. Neutral position switch (only mechanically operated
reverse gear)10. Potentiometer, throttle opening/gear shift
10a. Control adapter, throttle opening10b. Control adapter, gear shift
Wiring diagrams
36
Control system, EDC: TAMD74
Twin engine installation. Single lever controls.
Cable colourBL = BlueBN = BrownGN = GreenOR = OrangeP = PinkR = RedSB = BlackW = WhiteY = Yellow
Cable areas = 0.75 mm²unless otherwisespecified.
Twin engine installation. Twin lever controls.
Cable colourBL = BlueBN = BrownGN = GreenOR = OrangeP = PinkR = RedSB = BlackW = WhiteY = Yellow
Cable areas = 0.75 mm²unless otherwisespecified.
Position schedule (both wiring diagrams)
5. Synchronisation button5a. LED (blue)6. LED for background illumination7. Operating button
7a. LED ,2 pcs(red), starboard and port8. Potentiometer, throttle opening/gear shift
8a. Control adapter, throttle opening8b. Control adapter, gear shift9. 8-pin moisture-proof connector (male)
10. 8-pin moisture-proof connector (female)11. Neutral position switch (only mechanically
operated reverse gear)
1. Control panel2. Connector3. Diagnostic button
3a. LED (yellow)4. Neutral button
4a. LED (green)
Wiring diagrams
37
Wiring diagrams – general
Connection of Charge splitter to standardAlternator
1. Sensor cable (yellow, 1,5 mm2)2. Charge splitter (optional)3. Voltage regulator4. Alternator5. Fuse panel (optional)
6. Starter motor7. Main switch8. Accessory batteries (for
optional equipment)9. Start batteries (engine)
Oil scavenging pump
Extra Alternator 28V/100A
Extra Alternator 28V/100A1. Key switch2. Charge indication lamp3. Resistor (47Ω/25W)4. Alternator5. Battery (12V)
Proposed connection of oil scaveng-ing pump (emptying and filling)
A. Fuse (8A)
Cable area: 1,5 mm²
38
Wiring diagram – EDC colour coding
Wiring diagrams
39
MS
Twin engine installation
Extension cable3, 5, 7, 9 and 11 m
Extension cable3, 5, 7, 9 and 11 m
MS unit
Serialcommunication
Branch connection
Extension cable3, 5, 7, 9 and 11 m
Engine
m F = Female connector
l M = Male connector
Cable colourBL = BlueLBL = Light blueBN = BrownLBN = Light brownGN = GreenGR = GreyOR = OrangeR = RedSB = BlackVO = VioletW = WhiteY = YellowP = Pink
6 press buttons, Port 6 press buttons, Starboard 3 press buttons
40
Wiring diagrams – alternative control systemfor EDC-controls
Wiring diagrams
41
Engine
Alternativecontrols
Mechanical controls and electrically operated reverse gear
Alternativecontrols
Single engine installation:
Electrically controls and electrically operated reverse gear
Engine
1. Control panel EDC, main control position2. Controls, main control position3. Throttle control potentiometer4. Connector, gear position potentiometer (not used)5. Connector, neutral position switch (not used)6. Connector (TAMD72P has 16-pin., TAMD73P has
16- or 2 x 8-pin., TAMD74 has 2 x 8-pin.connectors)
7. Connector, to engine (TAMD72P has 16-pin.,TAMD73P has 16- or 2 x 8-pin., TAMD74 has 2 x8-pin. connectors)
8. MS unit* (for alternative control position)
* Note. MS = Multi Station.
1. Control panel, main control position2. Controls, main control position3. Throttle control potentiometer4. Gear position potentiometer5. Connector, neutral position switch (not used)6. Connector (TAMD72P has 16-pin., TAMD73P has
16- or 2 x 8-pin., TAMD74 has 2 x 8-pin.connectors)
7. Connector, to engine (TAMD72P has 16-pin.,TAMD73P has 16- or 2 x 8-pin., TAMD74 has 2 x8-pin. connectors)
8. MS unit* (for alternative control position)
* Note. MS = Multi Station.
Wiring diagrams
42
Mechanical controls and mechanically operated reverse gear
Engine
Alternativecontrols
1. Control panel EDC, main control position2. Controls, main control position3. Throttle control potentiometer4. Connector, gear position potentiometer (not
used)5. Neutral position switch6. Connector (TAMD72P has 16-pin., TAMD73P
has 16- or 2 x 8-pin., TAMD74 has 2 x 8-pin.connectors)
7. Connector, to engine (TAMD72P has 16-pin.,TAMD73P has 16- or 2 x 8-pin., TAMD74 has2 x 8-pin. connectors)
8. MS unit* (for alternative control position)
* Note. MS = Multi Station.
Twin engine installation:
Electrical controls and electrically operated reverse gear
Alternativecontrols
Engine
Alternativecontrols
Engine
1. Control panel EDC, main control position2. Controls, main control position3. Throttle control potentiometer4. Connector, gear position potentiometer (not used)5. Connector, neutral position switch (not used)
6. Connector, (TAMD72P has 16-pin., TAMD73P has 16- or2 x 8-pin., TAMD74 has 2 x 8-pin. connectors)
7. Connector, to engine (TAMD72P has 16-pin., TAMD73Phas 16- or 2 x 8-pin., TAMD74 has 2 x 8-pin. connectors)
8. MS unit* (for alternative control position)
* Note. MS = Multi Station.
Wiring diagrams
43
Mechanical controls and electrically operated reverse gear
Alternativecontrols
Engine
Alternativecontrols
Engine
1. Control panel EDC, main controls2. Controls, main control position3. Throttle control potentiometer4. Gear position potentiometer5. Connector, neutral position switch (not used)
6. Connector (TAMD72P has 16-pin., TAMD73P has 16- or 2 x8-pin., TAMD74 has 2 x 8-pin. connectors)
7. Connector, to engine (TAMD72P has 16-pin., TAMD73P has16-or 2 x 8-pin., TAMD74 has 2 x 8-pin. connectors)
8. MS unit* (for alternative control position)
* Note. MS = Multi Station.
Mechanical controls and mechanically operated reverse gear
Alternativecontrols
Engine
Alternativecontrols
Engine
1. Control panel EDC, main control position2. Controls, main control position3. Throttle control potentiometer4. Connector, gear position potentiometer (not used)5. Neutral position switch
6. Connector (TAMD72P has 16-pin., TAMD73P has 16- or2 x 8-pin., TAMD74 has 2 x 8-pin. connectors)
7. Connector, to engine (TAMD72P has 16-pin., TAMD73Phas 16- or 2 x 8-pin., TAMD74 has 2 x 8-pin. connectors)
8. MS unit* (for alternative control position)
* Note. MS = Multi Station.
44
Wiring diagram – control panel water jet
Wiring diagrams
45
Control panel, water jet: TAMD73WJ-A, TAMD74C-A, TAMD74C-B K28/K32
1. Solenoid valve, back flush2. Solenoid valve, clutch in3. Cables to reverse gear4. Connector, 4-pin5. Extension cable (available in various
lengths from 3 –13 m)6. Pushbutton, flushing7. Pushbutton, clutch in8. Relay, clutch in9. Pushbutton, clutch out
10. Battery (–)11. Battery (+)12. Control panel
Cable colourBL = Blue SB = BlackBN = Brown W = WhiteGN = Green Y = YellowR = Red
Cable areas in mm² are specified afterthe colour code in the wiring diagrams.
When no area is specified, 1.0 mm² isapplicable.
46
Reversing bucket operation – water jet
Wiring diagrams
47
Cable colourBL = BlueBN = BrownGN = GreenR = RedSB = BlackW = White
1. Relay (not supplied by Volvo Penta)2. Junction box3. Connections to key switch on instrument panel4. Supply 12/24 V DC (5 –10 A)5. Microswitch (Reversing bucket down)6. Microswitch (Reversing bucket up)7. Control solenoid for hydraulic valve for reversing bucket
1 = Port A – Reversing bucket down2 = Port B – Reversing bucket up
Cable areas in mm² are specified after thecolour code in the wiring diagrams.
When no area is specified, 1.0 mm² isapplicable.
Reversing bucket, water jet: TAMD74C-A, TAMD74C-B K28/K32
48
References to Service Bulletins
Group No. Date: Refers to
.........................................................................................................................................................................................
.........................................................................................................................................................................................
.........................................................................................................................................................................................
.........................................................................................................................................................................................
.........................................................................................................................................................................................
.........................................................................................................................................................................................
.........................................................................................................................................................................................
.........................................................................................................................................................................................
.........................................................................................................................................................................................
.........................................................................................................................................................................................
.........................................................................................................................................................................................
.........................................................................................................................................................................................
.........................................................................................................................................................................................
.........................................................................................................................................................................................
.........................................................................................................................................................................................
.........................................................................................................................................................................................
.........................................................................................................................................................................................
.........................................................................................................................................................................................
.........................................................................................................................................................................................
.........................................................................................................................................................................................
.........................................................................................................................................................................................
.........................................................................................................................................................................................
.........................................................................................................................................................................................
.........................................................................................................................................................................................
.........................................................................................................................................................................................
.........................................................................................................................................................................................
.........................................................................................................................................................................................
.........................................................................................................................................................................................
.........................................................................................................................................................................................
.........................................................................................................................................................................................
.........................................................................................................................................................................................
.........................................................................................................................................................................................
.........................................................................................................................................................................................
.........................................................................................................................................................................................
Report form
Do you have any comments or complaints about this manual? Please take a copyof this page, write your comments on it and send it to us. The address is at thebottom. We would appreciate it if you were to write in English or Swedish.
From: ............................................................................
......................................................................................
......................................................................................
......................................................................................
Refers to publication: .............................................................................................................................................
Publication no: ............................................................... Date of issue: .................................................................
Suggestion/Motivation: ..........................................................................................................................................
..............................................................................................................................................................................
..............................................................................................................................................................................
..............................................................................................................................................................................
..............................................................................................................................................................................
..............................................................................................................................................................................
..............................................................................................................................................................................
..............................................................................................................................................................................
..............................................................................................................................................................................
Date: ................................................................
Name: ..............................................................
AB Volvo PentaTechnical InformationSE-405 08 Göteborg
Sweden
77
40
19
3-3
Eng
lish
11
–2
00
0