Wrapped in Plaid · a. Adhere the Wrapped in Plaid Specialty Designer Series Paper to the back of the Whisper White piece with the punched tree i. Tip: Be sure plaid design shows

Stamp Class by Mail – November 2019

Wrapped in Plaid

Stampin’ Up! Demonstrator: Jeanna Wieselmann Email: [email protected] | Website: www.mysweetpaper.com

Christmas Cheer Card

mailto:[email protected]

http://www.mysweetpaper.com/


Wrapped in Plaid


1. Stamp with Night of Navy ink: a. “Hoping that your busy year…” on 4” x 2 3/4” piece of Whisper White cardstock b. “Merry Christmas” on inside of Thick Whisper White card base - if you prefer, you could stamp

this in Cherry Cobbler ink c. Christmas tree on Shaded Spruce cardstock

i. NOTE: Stamp a total of 3 trees, one for each card 2. Stamp with Cherry Cobbler ink:

a. Using the “fill-in” stamp for the Christmas tree, stamp the entire piece of Cherry Cobbler cardstock to create a custom-patterned designer cardstock

3. Using the Pine Tree Punch: a. Punch Shaded Spruce Trees b. Punch Trees from the 5 ½” x 2 ½” Whisper White cardstock

i. NOTE: Punch 3 trees, one for each card 4. To create Cherry Cobbler banner, mark the center (½”) along the bottom edge of the Cherry Cobbler

cardstock. Using Paper Snips, make a ½” vertical cut. Then cut from the bottom left-hand corner to the top of the vertical cut you just made. Repeat from the right-hand side to create your banner.

a. TIP: The Banner Triple Punch is a quick way to make a banner if you have it! 5. Assemble the card using SNAIL adhesive:

a. Adhere the Whisper White outside piece to the Night of Navy cardstock so that you have equal borders on all 4 sides.

b. Adhere the Wrapped in Plaid Specialty Designer Series Paper to the left side of the assembly in Step a. The left vertical edge aligns with the left vertical edge of the Whisper White piece.

c. Adhere the Cherry Cobbler banner and trim off any excess. d. Adhere this assembly to the card base. e. Adhere the Whisper White Tree to the back of the Shaded Spruce tree so that just a little of the

Whisper White tree is showing on the left side. 6. Use Dimensionals to attach the layered tree to the front of your card.




Wrapped in Plaid


Cherry Cobbler Christmas Card




Wrapped in Plaid


1. Stamp with Cherry Cobbler ink: a. “Hoping that your busy year…” on the inside of the Thick Whisper White card base b. Stamp two Christmas Trees on 2 ½” x 2 ½” Whisper White cardstock. Ink stamp, stamp off one

time on scratch paper, stamp one tree on the left side approximately ½” from the bottom edge and close to the left edge. Then, without re-inking the stamp, stamp a second tree up and to the right of the first tree.

2. Clean Christmas Tree stamp. 3. Stamp with Shaded Spruce ink:

a. Christmas Tree on 5 ½” x 2 ½” Whisper White cardstock i. NOTE: Stamp 3 trees, one for each card

b. Christmas Tree on inside of card base if desired 4. Use the Pine Tree Punch to punch trees stamped on 5 ½” x 2 ½” Whisper White cardstock. Trim off the

tree trunk. 5. Assemble the card:

a. Use Mini Glue Dots to adhere 3/8” Cherry Cobbler Diagonal Stripe Ribbon to upper left corner of Whisper White cardstock that was stamped with Cherry Cobbler trees.

i. TIP: Use glue dots on each end and on the middle of the ribbon to firmly secure it. b. Use SNAIL to attach the Whisper White cardstock with the ribbon to the Cherry Cobbler

cardstock. c. Use SNAIL to attach the Wrapped in Plaid Specialty Designer Series Paper to the lower half of

the 4” x 3 ¼” Whisper White cardstock, leaving an equal border around the left, right, and bottom.

d. Use Multipurpose Liquid Glue to attach the narrow Shaded Spruce cardstock to top edge of designer series paper, overlapping just slightly

e. Use Dimensionals to attach the Christmas tree layer with ribbon to the assembly with the designer series paper, leaving equal borders on the left, right, and top.

f. Use Dimensionals to attach this assembly to the front of the card base. g. Use Dimensionals to attach the Shaded Spruce Christmas Tree. h. Add 3 Pearls to the Shaded Spruce tree.

i. TIP: Paper Snips, the Take Your Pick tool, or a tweezer can be helpful for placing the pearls.




Wrapped in Plaid


Plaid Christmas Tree Card




Wrapped in Plaid


1. Use the Pine Tree punch to punch a tree from one piece of 3 ¼” x 2 7/8” Whisper White cardstock. a. Tip: Slide 2 7/8” edge into the punch. Push cardstock into the punch until it hits the back of the

punch. The left and right edges of the cardstock should align with the punch edges. 2. Stamp with Cherry Cobbler ink:

a. “May this special season…” below the punched Christmas Tree b. “Merry Christmas” on second 3 ¼” x 2 7/8” Whisper White cardstock

3. Stamp with Shaded Spruce ink: a. Randomly stamp Plaid Christmas Tree on the 4” x 2 ½” Shaded Spruce cardstock b. Plaid Christmas Tree on punched Whisper White tree

i. Tip: The Christmas tree is not symmetrical, so make sure the stamp and punched tree are oriented the same way.

4. Use SNAIL adhesive to assemble the Cherry Cobbler “mini-card”: a. Adhere the Wrapped in Plaid Specialty Designer Series Paper to the back of the Whisper White

piece with the punched tree i. Tip: Be sure plaid design shows through to the front. Make sure the horizontal and

vertical lines of the plaid are straight. b. Adhere this assembly to the Gold Foil. c. Use a Bone Folder to crease the Cherry Cobbler cardstock along the score line. d. Attach the tree assembly to the front of the Cherry Cobbler “mini-card”. e. Attach the inside greeting to the Cherry Cobbler “mini-card”.

5. Use SNAIL adhesive to finish assembling the card: a. Use a Bone Folder to crease the Shaded Spruce card base along the score line. b. Attach the stamped piece of Shaded Spruce cardstock to the small section of the Shaded Spruce

card base. c. Orient the Shaded Spruce card base so that the fold is toward the bottom, then open the card. d. Attach the Cherry Cobbler “mini-card” to the inside of the Shaded Spruce card base, leaving

equal borders on the left, right, and top. e. Adhere the stamped Christmas tree to the inside of the Shaded

Spruce card base as shown to the right. 6. Tie bow in ribbon and attach to the top of the tree on the front of the card

with a Mini Glue Dot.




Wrapped in Plaid


Stampin’ Up!® Supplies Used:




Wrapped in Plaid


Optional Stampin’ Up!® Supplies:



Documents

Wrapped in Plaid · a. Adhere the Wrapped in Plaid Specialty Designer Series Paper to the back of the Whisper White piece with the punched tree i. Tip: Be sure plaid design shows