Upload
others
View
11
Download
0
Embed Size (px)
Citation preview
X320 (MS-1351) Assembly Guide
■ 1、LCD MODULE ASSY
■ 2、UPPER CASE ASSY
■ 3、LOWER CASE ASSY-1
■ 4、THERMAL-KIT
■ 5、HDD MODULE
■ 6、DRAM、WLAN MODULE
■ 7、ASSEMBLE UPPER CASE AND LOWER CASE
■ 8、KEYBOARD
■ 9、LOWER CASE ASSY-2
■ 10、BATTERY PACK
X320(MS-1351)Assembly Guide
1、LCD MODULE ASSY
1.1:Assemble the Antenna board to the LCD cover
fixed position as left picture shows;
Component Part No Qty
Antenna S79-1800G00-J36 1
LCD Cover 307-351A211-TC7 1
1.2:Assemble the MIC Module as left picture
Shows;
Attention:MIC Module needs along with LCD
Cover flute.
Component Part No Qty
MIC Module S34-2100900-N44 1
1.3:Cover MIC Module with MIC Sponge as
left picture shows;
Component Part No Qty
MIC Sponge E2Y-3511911-Y42 1
X320(MS-1351)Assembly Guide
1、LCD MODULE ASSY
1.4:Assemble CMOS Camera Module follow the
instruction as left picture shows. Then stick the
copper film to the LCD cover to fix the module.
Attention:Don’t assemble the CMOS Camera
Module with too strong force avoid damage the
module.
Component Part No Qty
Camera Module S1F-0001460-B36 1
1.5:Connect the Coaxial Cable(Camera Cable)
in the direction of the arrow in the picture;
Component Part No Qty
INT Coaxial Cable K19-3023002-H58 1
1.6:Arrange the cable to the fixed position as the
picture shows;
Attention: MIC Cable and Camera Cable cannot lap
over when arranging avoid damage the panel.
X320(MS-1351)Assembly Guide
1、 LCD MODULE ASSY
1.7:Connect LVDS Cable to Display Module and
fix the cable with black tape;
1.8:Insert the Display Module to the slot from left
side and make it be placed into the LCD Cover
completely.
Component Part No Qty
Display Module S1J-342G001-CC1 1
1.9:Shift the hook to be locked state in the
direction of the arrow. Then stick the two
Hook Sponge to fix.
Component Part No Qty
Hook Sponge E2Y-3511411-Y42 2
X320(MS-1351)Assembly Guide
1、 LCD MODULE ASSY
1.10:Stick three magnet to the position as left
picture shows;
Component Part No Qty
LCD Cover Magnet E2Y-3510711-SF7 2
LCD Cover Magnet E2Y-3511011-SF7 1
1.11:Assemble the left and right LCD Hinge as left
picture shows;
Component Part No Qty
Hinge R E2M-3510111-G60 1
Hinge L E2M-3510211-G60 1
1.12:Lock 8pcs M2*3mm screws with auto driver;
Attention:Set the auto-driver force at
2.0-2.2Kgf-cm.
Component Part No Qty
Screw E43-1203003-H29 8
X320(MS-1351)Assembly Guide
1、 LCD MODULE ASSY
1.13:When assemble LCD Bezel, please start
from down wards. Assemble the 5pcs hooks
downward to be ok and then right, top wards,
finally the left hook.
Component Part No Qty
LCD Bezel 307-351B211-TC7 1
1.14:Arrange the left and right Hinge Cap as left
picture shows;
Attention:Cannot press the cables when assemble
the hinge cap.
Component Part No Qty
Hinge Cap E2P-3510311-Y31 2
1.15:Stick the 4pcs Cover Rubber and 1pcs Bezel
Rubber as left picture shows;
Component Part No Qty
Cover Rubber E2Y-3510111-Y40 4
Bezel Rubber E2Y-3510211-Y40 1
X320(MS-1351)Assembly Guide
2、UPPER CASE ASSY
2.1:Assemble the Touchpad Module to Upper
Case fixed position and then cover it with Mylar;
Component Part No Qty
Touchpad Module S78-3700360-SK9 1
Upper Case 307-351C111-Y31 1
2.2:Assemble Touchpad Board to Upper Case
fixed position and then lock 2pcs 2*3.5mm screws;
Attention:Set the auto-driver force at.1.5-2.0
Kgf-cm
Component Part No Qty
Screw E43-1203501-H29 2
Touchpad Board 607-1351Q-01S 1
2.3:Connect the Touchpad Cable (To Button
Board) to Touchpad Module,then fix the Touchpad
Cable with hook; Then paste the acetate tape on
the connector and cable.
Component Part No Qty
FFC Cable (To MB) K1C-1012038-J36 1
FFC Cable (To Button) K1C-1020006-J36 1
X320(MS-1351)Assembly Guide
3、LOWER CASE ASSY-1
3.1:Assemble Speaker Module to Lower Case,
lock 3pcs M2*3.5mm screws with auto-driver;
Attention:Set the auto-driver force at. 1.5-1.8
Kgf-cm.
Component Part No Qty
Screw E43-1203501-H29 3
Speaker Module S33-A020210-F33 1
Lower Case 307-351D111-W28 1
3.2:Assemble R USB Cover to Lower Case fixed
position.
Component Part No Qty
R USB Cover E2P-3511111-D37 1
3.3:Assemble SD Card Cover to Lower Case fixed
position.
Component Part No Qty
SD Card Cover E2P-3511311-D37 1
X320(MS-1351)Assembly Guide
3、LOWER CASE ASSY-1
3.4:Assemble L USB Cover to Lower Case fixed
position.
Component Part No Qty
L USB Cover E2P-3511011-D37 1
3.5:Assemble Fan to M/B as left picture shows;
Attention:Fan Cable needs go from the M/B hole.
Component Part No Qty
Main Board 607-13511-01S 1
3.6:Assemble the M/B to Lower Case fixed
position.
X320(MS-1351)Assembly Guide
3、LOWER CASE ASSY-1
3.7:Lock 2pcs M2*3.5mm screws with auto-driver;
Attention:Set the auto-driver force at.
1.5-2.0Kgf-cm.
Component Part No Qty
Screw E43-1203501-H29 2
3.8:Assemble DSUB Cover and MODE Cover to
Left Side I/O Board;
Component Part No Qty
DSUB Cover E2P-3510811-D37 1
MODE Cover E2P-3510711-D37 1
3.9:Assemble Left Side I/O Board as left picture
shows;
Component Part No Qty
Left Side I/O Board 607-1351O-01S 1
X320(MS-1351)Assembly Guide
3、LOWER CASE ASSY-1
3.10:Lock 3pcs M2*3.5mm screws with auto
driver;
Attention:Set the auto-driver force at.
1.5-2.0Kgf-cm
Component Part No Qty
Screw E43-1203501-H29 3
3.11:Assemble 3.5G Board as left picture shows;
Component Part No Qty
3.5G Board 607-1351P-01S 1
3.12:Lock 2pcs M2*3.5mm screws with auto
driver;
Attention: Set the auto-driver force at.
1.5-2.0Kgf-cm
Component Part No Qty
Screw E43-1203501-H29 2
X320(MS-1351)Assembly Guide
3、LOWER CASE ASSY-1
3.13:Assemble Bluetooth Module as left picture
shows;
Component Part No Qty
Bluetooth Module 605-6837D-150 1
3.14:Lock 1pcs M2*3.5mm screws with auto
driver;
Attention:Set the auto-driver force at.
1.5-2.0Kgf-cm
Component Part No Qty
Screw E43-1203501-H29 1
3.15:Connect the Bluetooth Cable in the direction
of the arrow in left picture;
Component Part No Qty
Bluetooth Cable K10-3008091-H39 1
X320(MS-1351)Assembly Guide
3、LOWER CASE ASSY-1
3.16:Assemble Audio Cover and DCIN Cover to
Right Side I/O Board. Then connect LINK Cable to
the little board.
Component Part No Qty
LINK Cable K10-3024011-H39 1
Audio Cover E2P-3511411-D37 2
DCIN Cover E2P-3510911-D37 1
3.17:Assemble Right Side I/O Board as left picture
shows;
Component Part No Qty
Right Side I/O Board 607-1351N-01S 1
3.18:Lock 3pcs M2*3.5mm screws with auto
driver;
Attention:Set the auto-driver force at.
1.5-2.0Kgf-cm
Component Part No Qty
Screw E43-1203501-H29 3
X320(MS-1351)Assembly Guide
3、LOWER CASE ASSY-1
3.19:Connect Speaker Cable and MIC Cable in
the direction of the arrow in the picture;
3.20:Then connect LINK Cable;
3.21:Finally connect LVDS Cable;
Speaker Cable
MIC Cable
X320(MS-1351)Assembly Guide
3、LOWER CASE ASSY-1
3.22:Assemble LCD Module and then lock 3pcs
M2*3.5mm screws to fix the left hinge;
Attention:Set the auto-driver force at.
1.5-2.0Kgf-cm
Component Part No Qty
Screw E43-1203501-H29 3
3.23:Then lock 3pcs M2*3.5mm screws to fix the
right hinge;
Attention:Set the auto-driver force at.
1.5-2.0Kgf-cm
Component Part No Qty
Screw E43-1203501-H29 4
X320(MS-1351)Assembly Guide
4、THERMAL-KIT
4.1:Connect Fan Cable as left picture shows;
Component Part No Qty
Fan E33-0800080-MC2 1
4.2:Lock 3pcs M2*3.5mm screws with auto-driver;
Attention:Set the auto-driver force at.
1.5-2.0Kgf-cm
Component Part No Qty
Screw E43-1203501-H29 3
4.3:Assemble Heat sink and lock 2pcs M2*3.5mm
screws with auto-driver then stick the Mylar as left
picture shows.
Attention:Set the auto-driver force at.
1.5-2.0Kgf-cm.
Component Part No Qty
Screw E43-1203501-H29 2
Heatsink E31-0801200-TA9 1
X320(MS-1351)Assembly Guide
5、HDD MODULE
5.1:Assemble 3 Brackets to the HDD fixed
position.
Component Part No Qty
HDD Bracket 307-3510611-A89 3
HDD Module S71-2425526-W36 1
5.2:Lock 3pcs M3*3.5mm screws with auto-driver;
Attention:Set the auto-driver force at.
1.5-2.0Kgf-cm.
Component Part No Qty
Screw E43-1303502-H29 3
X320(MS-1351)Assembly Guide
5、HDD MODULE
5.3:Assemble HDD Module in the direction of
arrow in the left picture;
5.4:Lock 2pcs M2*3.5mm screws with auto-driver;
Attention:Set the auto-driver force at.
1.5-2.0Kgf-cm.
Component Part No Qty
Screw E43-1203501-H29 2
X320(MS-1351)Assembly Guide
6、DRAM、WLAN MODULE
6.1:Insert WLAN Module in the direction of arrow
in the left picture;
Component Part No Qty
WLAN Module 605-6896-010 1
6.2:Lock 1pcs M2*3.5mm screws with auto driver;
Attention:Set the auto-driver force at.
1.5-2.0Kgf-cm.
Component Part No Qty
Screw E43-1203501-H29 1
6.3:Connect the left and right antenna to the
WLAN Module as left picture shows.
X320(MS-1351)Assembly Guide
6、DRAM、WLAN MODULE
6.4:Insert RAM Module to the slot in the direction
of arrow in the left picture.
Component Part No Qty
RAM Module S7C-S357802-S02 1
6.5:Check the hook to fix RAM Module to be OK.
X320(MS-1351)Assembly Guide
7、ASSEMBLE UPPER CASE AND LOWER CASE
7.1:Connect Touchpad Cable in the direction
of arrow and then fix Touchpad Cable with hook;
7.2:When assemble Upper Case,please start
from down wards hooks to be ok and then left
& right, finally the top.
7.3:Lock 6pcs M2*3.5mm screws in turn shown
in the picture with auto-driver;
Attention:Set the auto-driver force at.
1.5-2.0Kgf-cm.
Component Part No Qty
Screw E43-1203501-H29 6
X320(MS-1351)Assembly Guide
8、KEYBOARD
8.1:Connect the K/B cable in the direction of arrow
in the left picture and then fix the cable by pushing
the drawer;
Component Part No Qty
Keyboard S1N-1ETC311-SA0 1
8.2:When assemble the K/B, first from the two
sides hook and then the top. Make sure all the
hooks are assembled to be OK.
X320(MS-1351)Assembly Guide
9、LOWER CASE ASSY-2
9.1:Lock 10pcs M2*2.5mm screws in turn with
auto driver;
Attention:Set the auto-driver force at.
1.5-2.0Kgf-cm.
Component Part No Qty
Screw E43-1202506-H29 10
9.2:Insert the Dummy Card in the direction of
arrow in the left picture.
Component Part No Qty
Dummy Card E2P-3512611-Y31 1
X320(MS-1351)Assembly Guide
10、BATTERY PACK
10.1:Assemble Battery Pack in the direction of
arrow in the left picture;
Attention:Battery Pack needs to slide into the slot
from the Open mark.
Component Part No Qty
Battery Pack S9N-2141400-SB3 1
10.2:Shift Unlock button to lock Battery Pack.
(MS-1351)screws specification
Photo Screw specification Label
(M2*L2.5MM) white
(M2*L3MM) white
(M2*L3.5 MM) black
(M3*L3.5 MM) white
(MS-1351)screws specification
■ 1、Lower Case ASSY total 10pcs screws;
specification:
Photo Screw specification Label
(M2*L2.5 MM) white
(MS-1351)screws specification
■ 2、Upper Case ASSY total 6pcs Screws;
specification:
Photo Screw specification Label
(M2*L3.5 MM) black
(MS-1351)screws specification
■ 3、Lower Case ASSY total 17pcs Screws;
specification:
照片 螺絲規格 標識
(M2*L3.5 MM) black
(MS-1351)screws specification
■ 4、HDD Module total 5pcs screws;
specification:
Photo Screw specification Label
(M2*L3.5 MM) black
(M3*L3.5 MM) white
(MS-1351)screws specification
■ 5、THERMAL-KIT total 5pcs screws:
specification:
Photo Screw specification Label
(M2*L3.5 MM) black
(MS-1351)screws specification
■ 6、Mainboard total 2pcs screws:
specification:
Photo Screw specification Label
(M2*L3.5 MM) black
(MS-1351)screws specification
■ 7、 Speaker Module total 3pcs screws;
specification:
Photo Screw specification Label
(M2*L3.5 MM) black
(MS-1351)screws specification
■ 8、 LCD Hinge total 8pcs screws;
specification:
Photo Screw specification Label
(M2*L3MM) white