XCAP Parameter Description _CDMA and EVDO

Analyzer Parameter Description

REV : 00

2006. 05.

© Copyright by Innowireless Co., Ltd. , 2005. All rights reserved.

Introduction

© Copyright by Innowireless Co., Ltd. Page I

Appendix Overview

XCAP Graph/Map/Table Parameter Tree drescription of Parameter for CDMA and EVDO

History

Edition Date Remarks

00 2006.05 First draft

Content

© Copyright by Innowireless Co., Ltd. Page I

Appendix Overview ................................................................................. I

History ................................................................................................. I

Graph/Map/Table Tab ..............................................................................1

GPS 1

Event ....................................................................................................... 1

CDMA ...................................................................................................... 2

Handoff Info .......................................................................................... 2

Power Control Info ................................................................................... 2

PMRM ................................................................................................. 3

Finger Info ............................................................................................ 3

Searcher Info ......................................................................................... 3

Frame Info ............................................................................................ 4

Configuration Info .................................................................................... 4

Voice Statistics ....................................................................................... 5

ESCAM ............................................................................................... 5

RLP Statistics ........................................................................................ 5

Pilot Sets ............................................................................................. 6

Access Probe ........................................................................................ 6

EVDO ....................................................................................................... 8

Summary Info ........................................................................................ 8

Air Link Summary .................................................................................... 8

Power Info ............................................................................................ 9

DRC Info .............................................................................................. 9

Finger Info .......................................................................................... 10

Searcher Info ....................................................................................... 10

Partial RLP ......................................................................................... 10

FWD Rate State ................................................................................... 10

Pilot Sets ........................................................................................... 11

State Info ........................................................................................... 12

Sector Info .......................................................................................... 12

Handoff Info ........................................................................................ 12

ARQ Effective Receive Rate ..................................................................... 12

목차 XCAP User’s Guide /Ed.00

Page II © Copyright by Innowireless Co., Ltd.

Reverse Rate Statistics ........................................................................... 13

Reverse Link Packet Summary .................................................................. 13

Slot Unit Info ....................................................................................... 13

Access Probe ...................................................................................... 13

Reverse Activity .................................................................................... 14

Nak 14

Attribute ............................................................................................. 14

CDMA Release A ....................................................................................... 19

Handoff Info .................................................................................. 19

PMRM ........................................................................................ 19

Searcher Info ................................................................................ 19

Finger Info ................................................................................... 20

F-CCCH Frame Info ........................................................................ 20

Enhanced Access Probe ................................................................... 20

Enhanced Finger Info ....................................................................... 21

ESCAM ....................................................................................... 21

EVDO Release A ....................................................................................... 22

Rvs CH Gain ................................................................................. 22

SU Fwd Statistics ........................................................................... 22

MU Fwd Statistics ........................................................................... 25

Rvs Info ...................................................................................... 27

RMAC Sub3 T2P Info ....................................................................... 30

Multi RLP Statistics ......................................................................... 30

Attribute ...................................................................................... 30

BCMCS ....................................................................................... 36

PN Scanner ............................................................................................. 40

PSC Scanner ............................................................................................ 41

XCAL-S ....................................................................................... 41

PPP Data ................................................................................................. 42

Mobile Rx/Tx ................................................................................. 42

Throughput info ........................................................................................ 43

System Info ............................................................................................. 44

Graph/Map/Table Tab

GPS

Parameter Description

Lon Longitude

Lat Latitude

Time Received Time of GPS Data

Head Movement direction of GPS(display as 360 degree of angle of direction)

Speed Received speed of GPS data

Distance Distance between current coordinate and previous coordinate

Source Received status of GPS(for example, the number of received satellite)

Data Ind Effectivity of received data from GPS

Event


Voice Call Change process of voice call in mobile station.

FTP Call Event Change process of data call in mobile station.

Browser Call Change process of EIF call in mobile station.

HTTP Call Event Change process of HTTP call in mobile station.

CS Call Event Change process of Circuit Switched call in mobile station.

E-Mail call Event Change process of POP3, SMTP call in mobile station.

User Event Received event from user in Diagnostic Measurement.

(The event is defined as F1~F9 by user)

Static Point Static position of In-Building data.

CDMA

Handoff Info


Handoff Statistics1 Handoff type for example, hard handoff, soft handoff, softer handoff, etc.

Handoff HDM TCE Count of allocation channel for handoff.

Search Window Size Range of window size when the handoff is occurred.

Active Window Size of Active Set

Neighbor Window Size of Neighbor Set

Remaining Window Size of Remaining Set

Handoff Parameter Signal power of mobile station when the handoff is occurred and related parameter.

T_add Signal power of a point of time when neighbor PN is converted to

active PN

T_drop Signal power of a point of time when active PN is converted to

neighbor PN

T_comp Permitted limit of active and cascade

T_tdrop Required time to remove the active PN after T_drop

Handoff Statistics2 Handoff information for Finger Info

The handoff type is displayed with PN offset 168.

Power Control Info


Rx Power Received power of mobile station.

Tx Power Transmitted power of mobile station.

Tx Adjust Difference between real transmitted power of mobile station and transmitted power

correspond with received power.

Reverse FCH Tx Power Transmitted power of Fundamental Channel in received platform.

Reverse SCH0 Tx

Power Transmitted power of Supplemental Channel in Antenna 0

Reverse SCH1 Tx

Power Transmitted power of Supplemental Channel in Antenna 1.

Reverse DCCH Tx

Power Transmitted power of Dedicated Control Channel in received platform.

Reverse Decision

History Statistics of Power Control Group that exists 16 in 1 Frame(20ms) of Reverse Link.

Forward FCH Setpoint Standard energy level for Fast Power Control of Fundamental Channel in Forward

Link

Forward SCH0 Setpoint Standard energy level for Fast Power Control of Fundamental Channel Antenna 0.

Forward SCH1 Setpoint Standard energy level for Fast Power Control of Fundamental Channel Antenna 1.

XCAP User’s Guide /Ed.00 목차

© Copyright by Innowireless Co., Ltd. Page 3

Forward DCCH Setpoint Standard energy level for Fast Power Control of Dedicated Control Channel in

Forward Link.

Forward FCH Decision

History

Statistics of Power Control Group that exists 16 in 1 Frame of Fundamental Channel

in Forward Link.

Forward SCH Decision

History

Statistics of Power Control Group that exists 16 in 1 Frame of Supplemental Channel

in Forward Link.

PMRM


Dominant PN The dominant PN among PNs in Pilot Measurement Report Message

Dominant Ec/Io Ec/Io(Chip Energy/Interference) of Dominant PN

PNs Each PN’s Ec/Io

Finger Info


Combined Ec/Io Combined signal power of received PN offset from 6 fingers.

Combined Ec Combined chip energy of received PN offset from 6 fingers.

Dominant PN Locked PN of finger of dominant signal power among 6 fingers.

Dominant Best Ec/Io Dominant Ec/Io of Dominant PN

Dominant Ec Dominant Ec of Dominant PN

Dominant Combined

Ec/Io Combined Ec/Io for the same dominant PNs.

Finger 1~6 PN PNs information of 6 fingers.

Finger 1~6 Ec/Io Finger’s Ec/Io of 6 fingers.

PNs Ec/Io for each locked PN.

At this time the first data in parenthesis is total data count the second is data count

that the Ec/Io is upper than -15dB.

Searcher Info


Best PN & Ec/Io Searcher Best PN The dominant PN among searcher PNs.

Searcher Best Ec/Io Ec/Io of dominant PN among searcher PNs.

PNs Ec/Io for each PN.



Frame Info


Frame Offset FWD Frame Offset Specifies the frame offset of forward Fundamental Channel

RVS Frame Offset Specifies the frame offset of reverse Fundamental Channel

Reverse FCH Frame Frame Count Count of frame for each reverse FCH Type

Full/Half/Quarter/Eight

h Frame #

Count of frame count of Full/Half/Quarter/Eighth Rate for

Reverse FCH frame.

Reverse SCH0 Frame Full/Blank/Erasure

Rate Frame # Count of frame count of Full/Blank/Erasure Rate

Full/Blank Frame Rate Frame rate of Full/Blank Frame Type

FER Frame error rate for reverse SCH0 frame

Reverse SCH1 Frame Full/Blank/Erasure



FER Frame error rate of reverse SCH1 frame

Forward FCH Frame Full/Half/Quarter/Eight

h Rate Frame #

Count of frame count of Full/Half/Quarter/Eighth Rate for

forward FCH frame.

Erasure & Blank Rate

Frame # Sum of Erasure and Blank Rate frame.

FER Erasure & Blank Rate Frame # / Total Frame Type #

Forward SCH0 Frame Full/Blank/Erasure



FER Frame error rate for forward SCH0 frame

Forward SCH1 Frame Full/Blank/Erasure



FER Frame error rate of forward SCH1 frame

Configuration Info


Reverse/Forward FCH RC Radio Configuration of Fundamental Channel in reverse/forward link.

Reverse/Forward SCH0 RC Radio Configuration of Supplemental Channel in reverse/forward link.

Reverse/Forward SCH1 RC Radio Configuration of Supplemental 1 Channel in reverse/forward link.

Reverse/Forward DCCH RC Radio Configuration of Dedicated Control Channel in reverse/forward link.

Reverse/Forward SO Service option of reverse/forward Link



Voice Statistics

Voice Statistics displays Markov or Voice Frame information


FER Error rate of voice frame.

Avg FER Average error rate of voice frame.

FEB Rate of Frame error bit

FER (2 sec) Average FER for 2 seconds.

ESCAM

ESCAM(Extended Supplemental Channel Assignment) displays Supplemental Channel

informations transmitting data in wireless network.


Forward SCH0~1 PN PN allocating the Supplemental Channel in forward link

Forward SCH0~1 DUR Supplemental Channel duration in forward link

Forward SCH0~1 RATE Supplemental Channel rate in forward link

Reverse SCH0~1 DUR Supplemental Channel duration in reverse link

Reverse SCH0~1 RATE Supplemental Channel rate in reverse link

FWD/RVS SCH0,1

Throughput [1sec]

Conversion value of Supplemental Channel’s average rate in forward/reverse link

for each 1 second

FWD/RVS SCH0,1

Throughput [Inst] Conversion value of Supplemental Channel’s rate for each event interval.

RLP Statistics

RLP Statistics displays Radio Link Protocol Parameter.


Service ID Service ID

Reset Time Timestamp for last statistics reset

Naks received Total count of nak frames received

Rex mits not found Count of Rexmits not found

Largest config Erasure Largest block of consecutive erasures

Resets Count of resets

Aborts Count of aborts (nak aborts)

Last RTT Round trip Time

RLP Blob Used 0-no BLOB, 1-NAK, 2-RTT, 3-NAK + RTT

Rx/Tx rexmit fr_count Count of received / transmitted re-transmitted frames

Rx/Tx idle fr_count Count of received / transmitted idle frames

Rx fill fr_count Count of received fill frames

Rx blank_fr_count Count of blank frames received

Rx null fr_count Count of null frames received

Rx/Tx new data fr_count Total count of received / transmitted new data frame count

Rx/Tx 20ms fr_count Count of received / transmitted Fundamental data frames

Rx/Tx total bytes Total count of bytes received / transmitted

Rx rlp erasures Count of RLP erasures received

Rx mux erasures Count of RLP mux erasures received

Tx naks count Count of tx naks entries to follow

Tx naks single count Single NAKs sent array

Tx naks double count Double NAKs sent array

Tx naks ets count Count of etc NAKs sent array

Pilot Sets


Combined Ec/Io Combined signal power of received PN offset from mobile station.

Combined Ec Combined chip energy of received PN offset from mobile station.

Dominant PN PN of finger of dominant signal power among received signal of mobile station.

Dominant Ec/Io Ec/Io for Dominant PN.

Dominant Ec Ec for Dominant PN

Rx Power Received power in debug mode status for mobile stations received power.

Tx Adjust Transmitted power in debug mode status for mobile stations transmitted adjusts

power.

Tx Power Transmitted power in debug mode status for mobile station’s transmitted power.

Active Active Set Count Active PN count of mobile station.

PN List Active PN list of mobile station.

Active Cell Count Active cell count of mobile station.

PNs Ec/Io for each active PNs of mobile station.

Candidate Ec/Io for each candidate PNs of mobile station.

Neighbor Ec/Io for each neighbor PNs of mobile station.

Pilot Pollution Count of Ec/Io’s PN bigger than user sets Ec/Io.

Access Probe


Sequence Number Sequence Number of Access Probe

Probe Number Count of Access Probe

Rx AGC Received Auto Gain Control Value ( Power )

Tx Adjust Transmit Gain Adjust

PSIST Count of Persistence tests performed

Channel Access Channel Number



Random Delay Randomization Delay of PN

Sequence Backoff Access Probe 의 Sequence Back Off

Probe Backoff Probe Back Off

EVDO

Summary Info


User Size Count of user for serviced PN

ASP Size Count of Active Set Pilot

ASP State PN information of Active Set Pilot

Cell Throughput Total throughput of serviced PN

Requested DRC

Throughput Conversion value of Data Requested Channel rate requested by mobile station.

Serving ASP PN Serviced PN among active set pilot

Serving ASP SINR C/I(Carrier/Interference) of serviced active set pilot

Serving ASP RTCOffset Reverse Traffic Channel offset of serviced active set pilot

Serving ASP PN DRC

Lock State DRC Lock Status of active set pilot

PER Packet Error Rate

Active Set Size Total count of active set

Active Cell Size Total count of active cell

Imbalance Info Imbalance Unity of best ASP in forward/reverse link

DB In Imbalance Difference of C/I between best ASP SINR and 1st ASP SINR

DRC Index VS Serving

ASP SINR Correlation with DRC Index Rate and Serving PN C/I

Network Serviced network of mobile station.

Air Link Summary


DRC Index Index of DRC rate requested by mobile station.

Best ASP Index ASP index of the strongest signal ASP

Best ASP PN PN of the strongest signal ASP

Best ASP SINR (Inst) Averaged value of received Best ASP PN’s SINRs that are sixteen.

Best ASP SINR (Filt) C/I of the strongest signal of ASP Filt SINR

PER Packet Error Rate

PER [x Frame] PER averaged according to user input frame count

PER [x Moving Avg] PER averaged value according to user input time(second)

ASP Index Count Count of ASP Index

PktRcvFlag Success or failure of receiving the last 16th slot

1st~3rd ASP PN PN of from first to third ASP signal

1st~3rd ASP SINR (Filt) C/I of from first to third ASP signal



Power Info


Rev.0 Tx Open Loop

Power

Open Loop Power of reverse link

PA ON/OFF Power when Power Amplifier is on/off

Rev.0 Tx Closed Loop

Power Adjust

Closed Loop Power of reverse link


Rev.0 Tx Pilot Power Pilot power of reverse link


Rev.0 Tx Total Power Total power of reverse link


Rev.A Tx Open Loop

Power

Open Loop Power of reverse link (1xEV-DO Rev A only)

Rev.A Tx Closed Loop

Power Adjust

Closed Loop Power of reverse link (1xEV-DO Rev A only)

Rev.0 Tx Pilot Power Pilot power of reverse link (1xEV-DO Rev A only)

Rev.0 Tx Total Power Total power of reverse link (1xEV-DO Rev A only)

Rx Power0 Received power of Antenna0


Rx Power1 Received power of Antenna1


Combined Rx Power Combined power between Rx Power 0 and Rx Power

PA ON/OFF Combined power when Power Amplifier is on/off

RPC History Status information for received power control

DRC Info

DRC Info displays data channel information requested by mobile station.


DRC Cover Cover value of best ASP requesting DRC

DRC Rate (Index) Index of DRC rate requested by mobile station

DRC Rate (Throughput) Conversion value of Data Requested Channel rate requested by mobile station

DRC Imbalance Unity status of best ASP between forward link and reverse link

DRC RL Best ASP Best ASP index in reverse link

DRC FL Best ASP Best ASP index in forward link

DSC Value[Index] The DSC value transmitted by the AT (1xEV-DO Rev A only)

ASP Index DRC Lock

State Lock state for each ASP Index(1st~6th)

DRC Lock Best ASP

[Handoff] Index, Lock state and effectively for Serving ASP PN

Best ASP PN DRC Lock

State PN, C/I, Lock state of Serving ASP

Finger Info


ASP State ASP PN Offset of finger

ASP State(Locked) Locked PN among received PN from finger

Best ASP PN PN of serving ASP

Best ASP C Preveious power standarized by C/I

= Best ASP C/I + Combined Rx Power

Best ASP C/I C/I of serving ASP

Best ASP RTCOffset Reverse Traffic Channel Offset of Best ASP for the first received signal

MSTR Pilot PN PN of the first received signal

1st ASP PN PN of the first ASP

1st ASP Ec/Io C/I of the first ASP

1st ASP RTCOffset Reverse Traffic Channel Offset of the first ASP

PNs Ec/Io of PNs in fingers

Searcher Info


Searcher Info PN, Ec/Io and Delay of searcher from first to forth

Partial RLP


Rx Received Bytes Second unit Bytes calculated by seqence number of message

Throughput Throughput conversed by received bytes

Tx Transmitted

Bytes Second unit Bytes calculated by seqence number of message

Throughput Throughput conversed by received bytes

FWD Rate State


Control Good CRC Good CRC Count of Control Channel

Bad CRC Bad CRC Count of Control Channel

Total Sum of Good CRC count and Bad CRC count



Throughput Throughput conversed by Good CRC count for each second

rate of Control Channel

PER Bad CRC Count of Control Channel / Total CRC Count [ % ]

Slot Counts with

Good CRC

Good Served CRC possession for second unit

Good CRC Sum / 600 Slot

Slot Counts with

Total

Total Served CRC possession for second unit


Good Good Served CRC Count for each rate

Bad Bad Served CRC Count for each rate

Total Total Served CRC Count for each rate

Traffic Good CRC Good CRC Count of Traffic Channel

Bad CRC Bad CRC Count of Traffic Channel

Total Sum of Good CRC count and Bad CRC count for Traffic

Channel


rate of Traffic Channel

PER Bad CRC Count of Traffic Channel / Total CRC Count [ % ]

Slot Counts with

Good CRC

Good Served CRC possession for second unit


Slot Counts with

Total

Total Served CRC possession for second unit Good CRC Sum /

600 Slot

Good Good Served CRC Count for each rate

Bad Bad Served CRC Count for each rate

Total Total Served CRC Count for each rate

Pilot Sets


PN Increment PN Increment used in mobile station

ASet Active Set

Count Count of active set

Window Search Window Size of active set

PNs PN of active set

CSet Candidate Set

Count Count of Candidate Set

Window Search Window Size of candidate set

PNs PN of candidate set

NSet Neighbor Set

Count Count of Neighbor Set

Window Search Window Size of neighbor set

PNs PN of neighbor set

Frequency Channel Number of active set

Band Class Band Class information of pilot set

Aset Best ASP PN PN of the strongest signal ASP

Best ASP Ec/Io Ec/Io of the strongest signal ASP

Combined Ec/Io Combined Ec/Io of active PN’s Ec/Io

State Info


AT State Inactive, Acquisition, Sync, Access, Connected

Session State Closed, AMP Setup, AT-Init Nego, AN-Init Nego, Open

ALMP State Inactive, Initialization, Idle, Connected

Init State Inactive, Network Determination, Pilot Acquisition, Sync

Idle State Inactive, Monitor, Sleep, Connection Setup

Connected State Inactive, Open

Route Update State Inactive, Idle, Connection Setup, Connected

Ovhd State Inactive, Process all messages, Sleep, Frequency Change In Progress Access

Handoff In Progress, Wait for Link

Sector Info


Sector ID Sector ID of base station

Subnet Mask 24 bit value for base station information

Color Code Color Code of base station

Handoff Info


Handoff State Handoff state for example hard handoff, soft handoff, softer handoff, etc

Handoff PNs PN occurred handoff

Handoff State2 Handoff state by finger

Handoff Finger PNs PN when finger handoff is occurred

Handoff Count Handoff Event count

ARQ Effective Receive Rate

ARQ Effective Receive Rate displays data type of decoded each rate.


Min Minimum rate received from HDR Decoder



Max Maximum rate received from HDR Decoder

Effective Receive Rate Effective received rate early terminated by HDR Decoder Interrupt in received packet

Reverse Rate Statistics


Avg Throughput Average Throughput information of Reverse Traffic Channel

Reverse Link Packet Summary


Reverse Rate Limit Rate Limit Value of Reverse Limit Message

Current Rate Transmitted rate of Reverse Traffic Channel

Combined Busy Bit Busy Bits for new rate

PA Max Limited Max PA for mobile station

Condition RRI Reverse Rate Index(Calculated) transmitted to Reverse Link Packet

Actual RRI Reverse Rate transmitted to Reverse Link Packet

Num Pad Bytes

RRI Demotion Unity between actual RRI and condition RRI

Random Variable Represents the random variable that was used to calculate the new reverse rate.

Transition Probability The transition probability (in units of 1/255) that was used to calculate the new

reverse rate.

Slot Unit Info


Air Link Summary DRC Index DRC Rate for slot unit

SINR_FOR_BESTAS

P C/I of the strongest signal PN

DRC Info Cover DRC Lock Index

Value (Index) DRC Rate

RL_ASP Reverse Link PN

FL_ASP Forward Link PN

ACK/NACK Acknowledgement or Unacknowledgement

DSC Value[Index] The DSC value transmitted by the AT (1xEV-DO Rev A

only)

Access Probe


1st A/P Rx Power Received power of the first access point

Tx Power Transmitted power of the first access point

Pilot Power Pilot Channel power of the first access point

Last A/P Probe Seq Count Probe Sequence Num

Probe Count Count of Access Probe

Duration Time duration between first probe and last probe

PN PN trying to access

Probe Num Step Probe Number of Probe Sequence

Max Probe Seq Max Probe Num of Probe Sequence

Rx Power Rx Power of a point of time to access

Tx Power Tx Power of a point of time to access

Pilot Power Pilot Ch Power of a point of time to access

Reverse Activity


ASP Index #1~#6 Reverse Activity Bit for each index of serving PN

ASP Index Total Reverse Activity Bit for all index of serving PN

Active PN 1st ASP PN ~ 3rd ASP PN PN of finger 1 to finger 3

Nak

Nak displays the data reception parameter.


Reverse Pilot PN of revserse link

Reverse Nak Request Count of ack requested for reverse link PN

Reverse Window Len Window Size of reverse link

Forward Pilot PN of forward link

Forward Nak Request Count of ack requested for forward link PN

Forward Window Len Window Size of forward link

Attribute


Stream Configuration Stream Application0

This field indicates the subtype of the

application used over Stream 0

Stream Application1



Stream Application2





Stream Application3



Prior Session

UATI

If the Restore field is set to ‘1’, the AT shall

set this field to the UATI associated with the

prior session.

Security Packet Length


set this field to the length of the Security

Packet field in octets.

Security Packet


set this field to the Security Packet variable

value.

Preferred Control

Channel Cycle Preferred Control Channel Cycle

Enabled

The sender shall set this field to ‘1’ if

Preferred Control Channel Cycle field is

included in this attribute; otherwise, the

sender shall set this field to ‘0’.

Preferred Control Channel Cycle

If Preferred Control Channel Cycle Enabled

is set to ‘1’, the sender shall included this

field and set it to specify the Control

Channel Cycle in which the AT transitions

out of the Sleep State in order to monitor

the Control Channel. The Sender shall omit

this field if Preferred Control Channel Cycle

Enabled is set to ‘0’.

Search Parameters

Pilot Increment

The AN shall set this field to the pilot PN

sequence increment, in units of 64 PN

chips, that AT are to use for searching the

Remaining Set.

Search Window Active Search window size for the Active Set and

Candidate Set

Search Window Neighbor Search window size for the Neighbor Set.

Search Window Remaining Search window size for the Remaining Set.

Set Management

Same/Difference

Channel Parameters Pilot Add

This value is used by the AT to trigger a

RouteUpdate in the Connected State. The

AN shall set this field to the pilot detection

threshold.

Pilot Compare

Active Set versus Candidate Set

comparison threshold, expressed as

a 2’s complement number. The AT

transmits a RouteUpdate message when

the strength of a pilot in the Candidate Set

exceeds that of a pilot in the Active Set by

this margin.

Pilot Drop

This value is used by the AT to start a pilot

drop timer for a pilot in the Active Set or the

Candidate Set. The AN shall set this field to

the pilot drop threshold.

Pilot Drop Timer

Timer value after which an action is taken

by the AT for a pilot that is a member of the

Active Set or Candidate Set, and whose

strength has not become greater than the

value specified by

PilotDrop.

Dynamic Thresholds

This field shall be set to ‘1’ if the following

three fields are included in this record.

Otherwise, this field shall be set to ‘0’.

Soft Slope

This field shall be included only if

DynamicThresholds is set to ‘1’. This field

shall be set to an unsigned binary number,

which is used by the AT in the inequality

criterion for adding a pilot to the Active Set

or dropping a pilot from the Active Set.

Add Intercept



shall be set to a 2’s complement signed

binary number in units of dB.

Drop Intercept



shall be set to a 2’s complement signed

binary number in units of dB.

Neighbor Max Avg

The AN shall set this field to the maximum

AGE value beyond which the AT is to drop

members from the Neighbor Set.

Initial Configuration

Probe Sequence Max

Maximum number of probe sequences. The

AN shall set this field to the maximum

number of probe sequences for a single

access attempt.

Probe Back Off

Inter-probe backoff. The AN shall set this

field to the upper limit of the backoff range

(in units of AccessCycleDuration) that the

AT is to use between probes.

Probe Sequence Backoff

Inter-probe sequence backoff. The AN shall

set this field to the upper limit of the

backoff range (in units of

AccessCycleDuration) that the AT is to use

between probe sequences.



DRG Gating

DRC Gated mode

The negotiable simple attribute for this

protocol is Continuous /DisContinuous

transmission.

DRC Lock

DRC Lock Period

The AN shall set this field to specify the

time interval in units of slots between

transmission of two consecutive DRCLock

bit transmissions on the Forward MAC

Channel.

DRC Lock Length

The AN shall set this field to specify the

number of times that a DRCLock bit is

repeated.

Handoff Delays

Softer Handoff Delay

The AN shall set this field to the minimum

interruption that the AT should expect when

the AT switches the DRC from a source

sector to a target sector where the

target sector is such that its Forward Traffic

Channel carries the same closed-loop

power control bits as the source sector.

Soft Handoff Delay

The AN shall set this field to the minimum

interruption that the AT should expect when

the AT switches the DRC from a source

sector to a target sector where the target

sector is such that its Forward Traffic

Channel does not always carry the same

closed-loop power control bits as the

source sector.

Power Parameters

DataOffsetNom

The AN shall set this field to the nominal

offset of the reverse link data channel

power to pilot channel power, expressed as

2's complement value in units of 0.5 dB.

DataOffset9k6

The AN shall set this field to the ratio of

access channel power at 9600 bps to the

nominal access channel power at 9600

bps.

DataOffset19k2




bps.

DataOffset38k4




bps.

DataOffset76k8




bps.

DataOffset153k6




bps.

RPCStep Reverse Power Control Step Value

Rate Parameters

Transition009k6_019k2

The field is set to the probability the AT

uses to increase its transmission rate to

19.2kbps if it is currently transmitting at

9.6kbps.





19.2kbps.





38.4kbps.





76.8kbps.



uses to decrease its transmission rate to

9.6kbps or lower if it is currently

transmitting at 19.2kbps.



uses to decrease its transmission rate to

19.2kbps or lower if it is currently

transmitting at 38.4kbps.

Default Session

Management

TSMPClose

Default is 54 hours.

all other values are in minutes.

(c.f 0x0000 means disable keep

alive messages)



CDMA Release A

Handoff Info


Handoff Statistics1 Handoff type for example, hard handoff, soft handoff, softer handoff, etc.

Handoff HDM TCE Count of Channel allocation according to handoff

Search Window Size Window Size range of mobile station related to handoff

Active Window Size of active set

Neighbor Window Size of neighbor set

Remaining Window Size of remaining set

Handoff Parameter Signal power of mobile station when the handoff is occurred and related parameter.

T_add Signal power of a point of time when neighbor PN is converted to

active PN

T_drop Signal power of a point of time when active PN is converted to

neighbor PN

T_comp Permitted limit of active and cascade

T_tdrop Required time to remove the active PN after T_drop

PMRM


Dominant PN The dominant PN among PNs in Pilot Measurement Report Message

Dominant Ec/Io Ec/Io(Chip Energy/Interference) of Dominant PN

DCCH FER Frame Error Rate of DCCH Channel

PNs Ec/Io of each PN

Searcher Info

Searcher Info 는 단말의 Searcher 를 통해 수집한 PN 을 Ec/Io 값으로 표시합니다.


Best PN & Ec/Io Searcher Best PN The dominant PN among searcher PNs.

Searcher Best Ec/Io Ec/Io of dominant PN among searcher PNs.

Active Ec/Io of active PN

Candidate Ec/Io of candidate PN

Neighbor Ec/Io of Neighbor PN

Remaining Ec/Io of Remaining PN

PNs Ec/Io for each PN.



Finger Info


PN State PN state received from finger

Locked PN State Locked PN in finger


Dominant PN Ec/Io Ec/Io of the strongest signal PN

Dominant Combined



Finger 1~6 Ec/Io, PN Ec/Io and PN data for top 1 to top 6, top is distinguished by Ec/Io

PNs Ec/Io for each locked PN.



F-CCCH Frame Info


Good Frame Good Frame Count

Bad Frame Bad Frame Count

Blank Frame Blank Frame Count

FER Frame Error Rate

Enhanced Access Probe


1st Access Probe

Rx Power Received power of mobile station at the first access point

Tx Power Transmitted power of mobile station at the first access point

Tx Adjust Transmitted adjust power of mobile station at the first access point

Last Access Probe

Seq_Num Probe Sequence Num

Prob_Num Count of access probe

Max Prob_Num Count of maximum access probe of probe sequence

Duration Probe Duration Time

Acc Rate Access Probe Rate

Rx Power Rx Power of a point of time to access

Tx Power Tx Power of a point of time to access

Tx Adjust Tx adjust Power of a point of time to access



Enhanced Finger Info


Rx Power 0 Rx Power of antenna 0

Rx Power 1 Rx Power of antenna 1

PN State PN state of finger

Locked PN State Locked PN in finger


Dominant PN Ec/Io Ec/Io of the strongest signal PN

Dominant Combined



Finger State Ec/Io and PN data for top 1 to top 4, top is distinguished by Ec/Io

ESCAM


SCH PN PN allocating the Supplemental Channel in forward link

Forward SCH0~1 DUR Supplemental Channel duration in forward link

Forward SCH0~1 RATE Supplemental Channel rate in forward link

Reverse SCH0~1 DUR Supplemental Channel duration in reverse link

Reverse SCH0~1 RATE Supplemental Channel rate in reverse link

FWD/RVS SCH0,1

Throughput [1sec]

Conversion value of Supplemental Channel’s average rate in forward/reverse link

for each 1 second

FWD/RVS SCH0,1

Throughput [Inst] Conversion value of Supplemental Channel’s rate for each event interval.

EVDO Release A

Rvs CH Gain


Trans Mode Transmission mode

PA State PA enabled

RPC Bit Reverse power control bit

Ratio Ack/Pilot[dB] Ratio of ACK channel power to pilot power

DRC/Pilot [dB] Ratio of DRC channel power to pilot power

RRI/Pilot[dB] Ratio of RRI channel power to pilot power

DSC/Pilot[dB] Ratio of DSC channel power to pilot power

Data/Pilot[dB] Ratio of Data channel power to pilot power

Aux/Data[dB] Ratio of Auxiliary pilot gain to data pilot power

SU Fwd Statistics

SU Fwd Statistics indicates the information about CRC and early-decode statistics for Rev A

forward traffic channel single-user packets and control channel packets.


Traffic Channel Packet Error Rate Packet error rate for single-user packet.

Throughput (slot

cumulated) This is the AT throughput during the time it is served by the AN.

Throughput (sec

cumulated)

This is the AT throughput averaged over time, including the time

the AN did not serve the AT.

Throughput (sec) This is the instantaneous AT throughput during 1sec.

CRC Info

TC0_128_Good Counter for DRC 0 [128, 16, 1024] traffic channel packets

with good CRC


with good CRC


with good CRC


with good CRC

TC0_Bad Counter for DRC 0 traffic channel packets with bad CRC


with good CRC


with good CRC




with good CRC


with good CRC


TC2_128_Good Counter for DRC 2 [128, 8, 512] traffic channel packets with

good CRC


good CRC


good CRC


good CRC



good CRC


good CRC


good CRC

TC3_1024_Good

Counter for DRC 3 [1024, 4, 256] traffic channel packets with

good CRC


TC4_128_Good


good CRC


good CRC


good CRC


good CRC



good CRC


good CRC



good CRC


good CRC


good CRC


good CRC


TC7_512_Good


good CRC

TC7_1024_Good


good CRC

TC7_2048_Good


good CRC



good CRC


good CRC


TC9_512_Good


good CRC

TC9_1024_Good


good CRC

TC9_2048_Good


good CRC


TC10_4096_Goo

d


good CRC


TC11_1024_Goo

d


good CRC

TC11_3072_Goo

d


good CRC


TC12_4096_Goo

d


good CRC


TC13_5120_Goo

d


good CRC




Short Control Channel

Throughput (slot

cumulated)

This is the AT throughput when served for control channel short

packet.

Throughput (sec

cumulated)

This is the AT throughput averaged over time, including the

time the AN did not serve the AT.


MU Fwd Statistics

MU Fwd Statistics indicates the information about CRC and early-decode statistics for Rev A

forward traffic channel multi-user packets.


Traffic Channel Packet Error Rate Packet Error rate for Multi-user packet.

Throughput (slot

cumulated)

This is the AT throughput during the time it is served by the

AN.

Throughput (sec

cumulated)

This is the AT throughput averaged over time, including the

time the AN did not serve the AT.


CRC Info

TC3_128_Good

Counter for DRC 3 [128,4,256] multiuser traffic channel

packets with good CRC

TC3_256_Good



TC3_512_Good



TC3_1024_Good



TC3_bad

Counter for DRC 3 multiuser traffic channel packets with

bad CRC

TC5_2048_Good



TC5_2048_bad Counter for DRC 5 multiuser traffic channel packets with

bad CRC

TC8_3072_Good



TC8_3072_bad


bad CRC

TC10_4096_Good

Counter for DRC 10 [4096, 2, 644,128] multiuser traffic

channel packets with good CRC

TC10_4096_bad


bad CRC

TC13_5120_Good

Counter for DRC 13 [5120, 2, 64]4,128] multiuser traffic

channel packets with good CRC

TC13_5120_bad


bad CRC



Rvs Info

Rvs Metric info indicates the information about reverse link traffic packet transmitted and the

early termination statistics for each packet size and transmission mode.


Total PER [cumulated]

The Packet Error Rate for transmitted Reverse link traffic

packet.

PER [sec] Transmitted PARQ NAK Count / Transmitted total packet

count

Throughput [sub-

pkt cumulated]

The total number of CRC passed bits received by AT/the

transmitted time.

Throughput [sec

cumulated]

Total number of CRC packet bits received by AT /log

packet sequence number

Throughput [sec] Throughput for both High Capacity and Low Latency

modes over all packet size.

Average Latency The total time of packet transmission

Interlaced Pkt info

Interlace [0]~[2]

# of Total

Packet sent

Total number of PS1 (128 bit~12288bit)

packets sent in this interlace

# of sub-pkt0

Ack

Number of Acks received for the second

subpacket of all PS (128 bit~12288bit)


# of sub-pkt1

Ack




# of sub-pkt2

Ack

Number of Acks received for the third

subpacket PS(128 bit~12288bit) packets

sent in this interlace

# of P-ARQ Ack

Number of P-ARQ Acks received after 4

subpackets for PS(128 bit~12288bit)


# of P-ARQ

Nack

Number of P-ARQ Nacks received after

4 subpackets for PS(128 bit~12288bit)


Interlaced Pkt info

Interlace Total

# of Total

Packet sent

Number of total packet from

intertace[0] to interace[2]

# of sub-pkt0

Ack

Number of total sub-pkt0 Ack from


# of sub-pkt1

Ack



# of sub-pkt2

Ack



# of P-ARQ Ack Number of total P-ARQ Ack from


# of P-ARQ

Nack

Number of total P-ARQ Nack from


HiCap Total PER


packet.

Total Instantaneous

PER

Transmitted PARQ NAK Count / Transmitted total packet

count

Total Transmitted

Throughput


transmitted time.

Total Overall

Throughput



Total Instantaneous

Throughput

Throughput for both High Capacity and Low Latency



Interlaced Pkt info

Interlace [0]~[2]

# of Total

Packet sent



# of sub-pkt0

Ack




# of sub-pkt1

Ack




# of sub-pkt2

Ack




# of P-ARQ Ack




# of P-ARQ

Nack




Interlaced Pkt info

Interlace Total

# of Total

Packet sent



# of sub-pkt0

Ack



# of sub-pkt1

Ack



# of sub-pkt2

Ack





# of P-ARQ

Nack





LoLat Total PER


packet.

Total Instantaneous

PER

Transmitted PARQ NAK Count / Transmitted total packet

count

Total Transmitted

Throughput


transmitted time.

Total Overall

Throughput



Total Instantaneous

Throughput

Throughput for both High Capacity and Low Latency



Interlaced Pkt info

Interlace [0]~[2]

# of Total

Packet sent



# of sub-pkt0

Ack




# of sub-pkt1

Ack




# of sub-pkt2

Ack




# of P-ARQ Ack




# of P-ARQ

Nack




Interlaced Pkt info

Interlace Total

# of Total

Packet sent



# of sub-pkt0

Ack



# of sub-pkt1

Ack



# of sub-pkt2

Ack





# of P-ARQ

Nack



RMAC Sub3 T2P Info

RMAC Sub3 T2P Info indicates the information about RTCMAC Subtype 3 T2P resource-

related information.


TxT2P T2P of packet currently being transmitted over the air.

Pilot Strength Pilot strength of packet currently being transmitted over the air.

Packet Size Packet size of the packet currently being transmitted over the air.

Normal HDR Mode True or False about Normal High Data rate (1XEV) mode.

FRAB Filtered Reverse Activity Bit.

QRAB Flow specific QRAB

T2P Outflow Raw value of actual T2P Resource withdrawn from this flow’s bucket in proportion to

its allotment.

Delta T2P Inflow Raw value of the T2P inflow increment or decrement for this flow.

T2P Inflow Raw value of the average T2P resource added to bucket for this flow.

Bucket Level Raw value of current bucket level

Bucket Saturation Level Raw value of the bucket saturation level.

Bucket Factor Raw value of the Bucket Factor (T2PInflow, FRAB ) function

Multi RLP Statistics


RLP Flow ID[0...N] Identifies RLP

Rx Received Bytes Total number of bytes received

Rx Throughput Multi RLP throughput for forward link

Tx Received Bytes Total number of bytes transmitted

Tx Throughput Multi RLP throughput for reverse link

Attribute


Enhanced FTC MAC DRCLockLength

The AN shall set this field to specify the number of times

that a DRCLock bit is repeated.

MultiUserPacket

Enabled

Enable or disable of multi user packet

DSCLength Length of a single DSC transmission

DRC Supervision

Timer

Value of DRC Supervision Timer

Handoff Delays

Attribute SofterHandoffDelay

The AN shall set this field to the

minimum interruption that the AT

should expect when the AT switches



the DRC from a source sector to a

target sector where the target sector

is such that its Forward Traffic

Channel carries the same closed-

loop power control bits as the source

sector.

SoftHandoffDelay

The AN shall set this field to the

minimum interruption that the AT

should expect when the AT switches

the DRC from a source sector to a

target sector where the target sector

is such that its Forward Traffic

Channel does not always carry the

same closed-loop power control bits

as the source sector.

Subtype 3 RTC MAC

ARQ Mode

The ARQMode is a 1bit value that indicates the modulation

(Bi-Polar (+1 implies ACK and −1 implies NAK) Keying or

ACK-oriented ON-OFF (+1 implies ACK and 0 implies NAK)

Keying) of the H-ARQ bit

Transmission

Mode NN

The transmission mode for flow NN indicates High Capacity

or Low Latency.

QRAB Select NN

The QRAB Select for flow NN indicate QRAB or QRABps.

c.f )

QRABn,s: Indicates the Quick RAB value from sector s at

sub-frame n.

QRABpsn: Indicates the effective Quick RAB value

generated at sub-frame n based on

2 PilotStrengthn, s of the sectors s in its active set.

Power Parameter

128 Attribute

LoLatT2P

transition128

LoLatT2PTransitionPS: Number of sub-

packets (excluding the first) from the

start of the packet for which the pre-

transition T2P values are used for Low

Latency mode Reverse Traffic Channel

transmissions with packet size PS.

LoLatTermination

Target128

The sender shall set this field to one

less than the expected number of sub-

frames needed to achieve the target

Physical Layer erasure rate for a

Reverse Traffic Channel packet with

packet size of 128 bits transmitted

using the Low Latency Mode.

HiCapT2P

transition128

HiCapT2PTransitionPS: Number of

sub-packets (excluding the first) from

the start of the packet for which the

pre-transition T2P values are used for

High Capacity mode Reverse Traffic

Channel transmissions with packet size

PS.

HiCapTermination

Target128

The sender shall set this field to one

less than the expected number of sub-

frames needed to achieve the target

Physical Layer erasure rate for a


packet size of 128 bits transmitted

using the High Capacity Mode.

T2PLoLatPre

Transition128

T2PLoLatPreTransition128 defines the

T2P's used by the AT for transmitting

the first LoLatT2PTransitionPS+1 sub-

packets of a Reverse Traffic Channel

packet with packet size128 in Low

Latency Mode.

T2PLoLatPost

Transition128

T2PLoLatPostTransition128 defines the


the subsequent sub-packets of a


packet size (128) in Low Latency

Mode.

T2PHiCapPre

Transition128

T2PHiCapPreTransition128 defines the


the first HiCapT2PTransition

PS+1 sub-packets of a Reverse Traffic

Channel packet with packet size (128)

in High Capacity Mode



T2PTransitionFuc

tionNN Attribute

NumT2PAxis

Values

This field indicates number of values

specified on the T2P axis minus 1.

NumFRABAxisVal

ues

This field indicates the number of

values specified on the FRAB axis

minus 1.

T2PAxis This field to values that define the T2P

axis.

FRABAxis This field to values that define the

FRAB axis.

T2PupT2PAxisFR

ABAxis

this field to the value of the function

T2PUp of the associated MAC flow at

[T2PAxis, FRABAxis].

T2PDnT2PAxisFR

ABAxis

This field to the value of the function

T2PDn of the associated MAC flow at

[T2PAxis, FRABAxis].

Enhanced Idle State

Preferred Control

CH Cycle

Attribute

PreferredControlC

hannelcycleEnabl

ed

This field indicates whether

PreferredControlChannelCycle is

enabled or not.

Preferred Control

Channel Cycle

This field is set to specify the Control

Channel Cycle in which the AT

transitions out of the Sleep State in

order to monitor the Control Channel.

Slotted Mode

Attribute

SlotCycle 1 This field indicates the Slotcycle1 in

slotted mode.

SlotCycle 2 SlotCycle2 shall be greater than or

equal to SlotCycle1

SlotCycle 3 SlotCycle3 shall be greater than or

equal to SlotCycle2.

WakeCount 1 This field indicates the WakeCount1 in

slotted mode.

WakeCount 2 WakeCount2 shall be greater or equal

to than WakeCount1.

Default Session

Management

TSMP Close TSMP Close

Default is 54 hours.

all other values are in minutes.

(c.f 0x0000 means disable keep

alive messages)

Multi-Flow Packet

Application MaxAbortTimer MaxAbortTimer

The max value of the RLP abort timer

for this forward link RLP flow in units of

ms.

FlowNNPhysical

LayerNak

EnableRvs

FlowNNPhysical

LayerNak

EnableRvs

This Field indicates whether RLP

retransmission is enabled or not.

FlowNNTimers

Fwd

AbortTimer

This field indicates the value of the RLP

abort timer for this forward link RLP

flow in units of ms.

FlushTimer

The sender shall set this field to the

value of the RLP flush timer for this

forward link RLP flow in units of ms.

FlowNNTimers

Rvs

AbortTimer

This field indicates the value of the RLP

abort timer for this reverse link RLP

flow in units of ms.

FlushTimer

The sender shall set this field to the

value of the RLP flush timer for this

reverse link RLP flow in units of ms.

ReservationKKQo

SRequestFwd

ProfileType

The AT shall use the Profile Type 0x00,

0x01, or 0x02 in the

ReservationKKQoSRequestFwd

attributes

ProfileLength Length of the Profile Value field in units

of octets.

ProfileValue

If Profile Type is equal to 0x00, then

the sender shall omit this field. If Profile

Type is equal to 0x01, if the

ANSupportedQoSProfiles attribute does

not have a default value, and if this

attribute is included in an

AttributeUpdateRequest then the

requested Flow Profile IDs shall be a

subset of the Flow Profile IDs in the

ProfileValue fields of

ANSupportedQoSProfiles attribute.

ReservationKKQo ProfileType The AT shall use the Profile Type 0x00,



SRequestRvs 0x01, or 0x02 in the

ReservationKKQoSRequestRev

attributes.


of octets.

ProfileValue

If ProfileType is equal to 0x00, then the

sender shall omit this field. If

ProfileType is equal to 0x01, if the









ReservationKKQo

SResponseFwd

ProfileType

The AN shall use Profile Type 0x00 or

0x03 in the

ReservationKKQoSResponseFwd

attributes.


of octets.

ProfileValue












ReservationKKQo

SResponseRvs ProfileType

The AN shall use Profile Type 0x00 or

0x03 in the

ReservationKKQoSResponseRev

attributes.


of octets.

ProfileValue












BCMCS


BOM Info Dominant PN The pilot PN in Broadcast Overhead Message.

Data Rate Physical Layer data rate and the number of slots in a Broadcast

Physical Layer packet used to transmit this logical channel.

Outer Code Reed-Solomon outer code is used to form an error control block

for this logical channel

I/M Pair Interlace and Multiplex Index

I/M Pair (%) Rate of Interlace and Multiplex Index

Soft Combine NeighborPilotPN Index included in the SectorParameters

message with signature equal to SectorSignature.

Neighbor Count NeighborPilotPN Count included in the SectorParameters


Neighbor PNs This field indicates the Neighbor PN when value of soft combine

is equal 1.

SoftCombine info NeighborPilotPN Index included in the SectorParameters


Neighbor Info NeighborPilotPN List included in the SectorParameters


MCastPktDec Info Control

Good CRC The difference between good CRC count of pre packets and

post packets In control channel.



Bad CRC The difference between bad CRC count of pre packets and post

packets In control channel.

Total The difference between total CRC count of pre packets and

post packets In control channel.


rate of Control Channel.

PER Bad CRC Count of control Channel / Total CRC Count [ % ]

Slot Utilization Slot Counts with

Good CRC

Good Served CRC possession for second

unit Good CRC Sum / 600 Slot

Slot Counts with

Total

Total Served CRC possession for second


Multicast

Good CRC The difference between good CRC count of pre packets and

post packets In multicast channel.

Bad CRC The difference between bad CRC count of pre packets and post

packets In multicast channel.

Total The difference between total CRC count of pre packets and

post packets In multicast channel.

PER Bad CRC Count of multicast Channel / Total CRC Count [ % ]

Slot Utilization Slot Counts with

Good CRC

Good Served CRC possession for second


Slot Counts with

Total

Total Served CRC possession for second


Good

BC 38400 Counter for 38.4 k traffic channel packets with good CRC

BC 76800 Counter for 76.8 k multicast packets with good CRC



BC 307200 Short Counter for 302.2 k (short) multicast packets with good

CRC

BC 307200 Long Counter for 307.2 k (long) multicast packets with good

CRC


BC614400Short Counter for 614.4 k (short) multicast packets with good

CRC

BC614400Long

Counter for 614.4 k (long) multicast packets with good

CRC

BC921600 Counter for 921.6 k multicast packets with good CRC

BC1228800Short

Counter for 1228.8 k (short) multicast packets with good

CRC

BC1228800Long

Counter for 1228.8 k (long) multicast packets with good

CRC

BC1843200 Counter for 1843.2 k multicast packets with good CRC

BC2457600 Counter for 2457. k multicast packets with good CRC

Bad

BC 38400 Counter for 38.4 k traffic channel packets with bad CRC

BC 76800 Counter for 76.8 k multicast packets with bad CRC



BC 307200 Short Counter for 302.2 k (short) multicast packets with bad

CRC

BC 307200 Long Counter for 307.2 k (long) multicast packets with bad

CRC


BC614400Short Counter for 614.4 k (short) multicast packets with bad

CRC

BC614400Long

Counter for 614.4 k (long) multicast packets with bad

CRC

BC921600 Counter for 921.6 k multicast packets with bad CRC

BC1228800Short Counter for 1228.8 k (short) multicast packets with bad

CRC

BC1228800Long Counter for 1228.8 k (long) multicast packets with bad

CRC

BC1843200 Counter for 1843.2 k multicast packets with bad CRC

BC2457600 Counter for 2457. k multicast packets with bad CRC

Total

BC 38400 Counter for 38.4 k traffic channel packets with total CRC

BC 76800 Counter for 76.8 k multicast packets with total CRC



BC 307200 Short Counter for 302.2 k (short) multicast packets with total

CRC

BC 307200 Long Counter for 307.2 k (long) multicast packets with total

CRC


BC614400Short Counter for 614.4 k (short) multicast packets with total

CRC



BC614400Long

Counter for 614.4 k (long) multicast packets with total

CRC

BC921600 Counter for 921.6 k multicast packets with total CRC

BC1228800Short Counter for 1228.8 k (short) multicast packets with total

CRC

BC1228800Long Counter for 1228.8 k (long) multicast packets with total

CRC

BC1843200 Counter for 1843.2 k multicast packets with total CRC

BC2457600 Counter for 2457. k multicast packets with total CRC

PER

BC 38400 Packet error rate of 38.4 k traffic channel packets

BC 76800 Packet error rate of 76.8 k multicast packets



BC 307200 Short Packet error rate of 302.2 k (short) multicast packets

BC 307200 Long Packet error rate of 307.2 k (long) multicast packets


BC614400Short Packet error rate of 614.4 k (short) multicast packets

BC614400Long Packet error rate of 614.4 k (long) multicast packets

BC921600 Packet error rate of 921.6 k multicast packets

BC1228800Short Packet error rate of 1228.8 k (short) multicast packets

BC1228800Long Packet error rate of 1228.8 k (long) multicast packets

BC1843200 Packet error rate of 1843.2 k multicast packets

BC2457600 Packet error rate of 2457. k multicast packets

PN Scanner


Center Frequency Center Frequency

Locked State Locked state of PN

Io Signal power of interference

Top 20 Ec/Io, Delay and Ec for 20 PNs of the strongest received power

PN Ec/Io Ec/Io for each PN

PN Delay Delay for each PN

PN Ec Ec for each PN



PSC Scanner

XCAL-S


Frequency 1/2/3 Center

Frequency Center Frequency

RSSI RSSI of Carrier Frequency

Tx Diversity

ON/OFF

Diversity indicates whether the diversity is enabled

for the AT

SC Ec/Io, RSCP and Delay Spread for each SC

TOP SC By SC, Ec/Io and RSCP for each Top SC ordered by Ec/No

signal

Neighbor List

Analysis Neighbor List of each cell by using scanner measurement data

PPP Data

Mobile Rx/Tx


Packet ID Packet ID

Duplicated Packets

Count Count of duplicated packets

Duplicated Packets ID ID of duplicated packets

Seq Num Sequence Number of TCP header received from mobile station

Next Seq Num Sum of packet sequence number and packet TCP/IP packet Len(Payload) received

from mobile station

Ack Num Ack Number of TCH header received from mobile station

Source Port FTP Server IP Number

Destination Port Client IP Number

TCP Flag TCP Flag is response message. The message indicates request or response of

TCP Layer.

Window Size Window Size of TCH header set when mobile station is received packet

PPP Throughput (Sec) 8 times of PPP frame per second of packet received from mobile station

Data Throughput (Sec) 8 times of TCP/IP frame per second of packet received from mobile station

APP Throughput (Sec) (Last Ack of previous second – last Ack of current second)×8

Inter Frame Time Difference of interval time between current packet and previous packet

Packet Count Count of received packet from mobile station per second

FCS Error FCS Error Packet ID

FCS Error Count FCS Error Packet count

Header CheckSum Error Header Checksum Error Packet ID

Header CheckSum Error

Count Count of Header Checksum Error Packet

PPP Frame Size PPP Header of disturffing packet+ IP Header + TCP Header + Packet

+ PPP Tailor

PPP Payload Size IP Header + TCP Header

Data Size Payload of packet

Total PPP Frame Size Total PPP Frame Len per call

Total PPP Payload Size Total PPP Payload Size per call

Total Data Size Total Data size per call



Throughput info


RLP FWD/RVS Throughput RLP layer throughput for forward/reverse link

Rx/Tx Bytes Total received byte in RLP layer of reverse/forward link

PPP FWD/RVS Throughput PPP layer throughput for forward/reverse link

Rx/Tx Bytes Total received byte in PPP layer of reverse/forward link

IP FWD/RVS Throughput IP layer throughput for forward/reverse link

Rx/Tx Bytes Total received byte in IP layer of reverse/forward link

TCP/UDP FWD/RVS Throughput TCP/UDP throughput for forward/reverse link

Rx/Tx Bytes Total received byte in TCP/UDP layer of reverse/forward link

APP FWD/RVS Throughput APP layer throughput for forward/reverse link

Rx/Tx Bytes Total received byte in APP layer of Reverse/forward link

Retransmission FWD/RVS Throughput Retransmission throughput from forward/reverse link

Rx/Tx Bytes Total received byte by retransmission of reverse/forward link

System Info


BID Base station ID connecting with mobile station

SID System ID connecting with mobile station

NID Network ID connecting with mobile station

FA Frequency of channel that mobile station is using

NETWORK Network serviced by mobile station

Transition Network (information) set by user


© C i ht b I i l C Ltd P 45

Analyzer Parameter

© Copyright by Innowireless Co., Ltd., 2005

All rights reserved.

Documents

XCAP Parameter Description _CDMA and EVDO