AM/FM/CD Receiver with Auxiliary Input, USB Charging Port and Detachable Face

XD1225

Charge Port

INSTALLATION/OWNER'S MANUAL

2

Preparation

TYPICAL MOUNTING METHOD

XD1225 INSTALLATION

Please read entire manual before installation.

Before You Start•Disconnectnegativebatteryterminal.Consultaqualifiedtechnicianforinstructions.•Avoidinstallingtheunitwhereitwouldbesubjecttohightemperatures,suchasfromdirectsunlight,orwhereitwouldbesubjecttodust,dirtorexcessivevibration.

Getting Started•Remove2transitscrewslocatedontopoftheunit.•Insertthesuppliedkeysintotheslotsasshown,andslidetheunitoutofthemounting

sleeve.•Installmountingsleeveintoopening,bendingtabstosecure.•Connectwiringharnessandantenna.Consultaqualifiedtechnicianifyouareunsure.•Certainvehiclesmayrequireaninstallationkitand/orwiringharnessadapter(sold

separately).•Testforcorrectoperationandslideinto mounting sleeve to secure. •Snaptrimringintoplace.

3

Rear Preamp OutputConnect to amplifier RCA input

Antenna Connector

RCA Cable(sold separately)

AMPBLUE

BLACK

RED

YELLOW

Remote Turn-OnConnect to amplifier or powerantenna. Insulate wire if not used.

GroundConnect to vehiclechassis ground.

AccessoryConnect to ignition circuit or switched 12 volt source.

MemoryConnect to battery circuit or constant 12 volt source.

Right FrontGray/Black (-)Gray (+)

Left FrontWhite/Black (-)White (+)

Right RearViolet/Black (-)Violet (+)

Left RearGreen/Black (-)Green (+)

5 AMPAGC Fuse

Wiring Diagram

FUSEWhen replacing the fuse, makesurenewfuseisthecorrect type and amperage. Using an incorrect fuse could damage the radio. TheXD1225usesone5ampAGC fuse located in-line.

* Caution-Donotattachanyspeakerleadstogroundasseveredamagewilloccur.

XD1225 INSTALLATION

4

Control Locations

Release

Mode / Power

Volume Knob

Display

Audio / Menu

Eject

USB Charging Port

Auxiliary Input

Preset 6

1

2

3

4

5

6

7

8

9

Preset5

Preset 4 / Play / Pause

Preset 3 / Intro

Preset 2 / Random

Preset1/Repeat

Band

Tune/TrackUp

Tune/TrackDown

10

11

12

13

14

15

16

17

1 2 3

8

XD1225 OPERATION

TheXD1225hasaneasy-to-useinterfacethatprovidesarewardingexperience,aswellassupportforyourfavoritetunes.AudioCD-RandCD-RWdiscplaybackensurescompatibility with your music collection, and the RCA preamp output provides the right connections to expand your system. From its front panel auxiliary input for connecting your MP3 player, to the detachable face for security assurance, this head unit has you covered.

4 65 7

91011121314151617

5

General OperationPress RELEASE and pull away from the left side to remove. Tore-install,insertrightsideoffaceplatefirstthenpushleftside to secure.

Removetrimringandinstallsupplied#1x7/32”Phillipsheadscrew through left side of mounting frame into faceplate.

Press  to turn the unit on. Inserting a CD will turn the unit on automatically. Press and hold for three seconds  to turn the unit off.

Press MODE to select between AM/FM, CD or auxiliary input. Modes of operation are indicated in the display.

Inserta3.5mmconnectorinthefrontpanelAUXport.Connecttheotherendofthe3.5mmconnectortotheheadphone output of an audio device, MP3 player, etc. Press MODEtoselectAUXmode.

Adjustvolumeusingthe rotary encoder(00-46).

Theradiofrequency(tunermode)andCDtrack/elapsedtime(CDplayermode)willbeshownbydefault.PressDISP to displaytheclock,andpressDISP again to return to default display.

Press and hold DISPfor2seconds,theclockwillbegintoflash. Press TRACK nntoadjustthehoursandTRACK ll toadjusttheminutes.PressDISPorwait5secondstosavetheclocksettings.

Theclockwilldisplay12-hourAM/PMtimeinUSAfrequencyspacingmode(PM10:00).InEuropeanfrequencyspacingmode,theclockwilldisplay24-hourtime(22:00).

Press and hold for more than 2 seconds to RESET the unit uponinitialinstallation.TheRESET button is located behind the faceplate.

Faceplate Removal

Semi-permanent Faceplate Installation

Power On/Off

Mode

Auxiliary Input

Volume

Display

Set the Clock

12/24-hour Clock 

Reset

XD1225 OPERATION

6

Insert the USB connector of a battery powered USB device into the USB charging port on the front panel, which provides5voltsDCand1.0amps.TheUSBdevicewillimmediately begin charging.

Note: TheUSBchargingportmaynotbecompatiblewitheverydeviceduetodifferencesinpowerrequirements.

Note:ThisUSBportprovidespoweronly,andwillnotplaybackmusicfromaUSBdevice.

Press AUDIOtoselectbetweenVolume(default),Bass,Treble,Balance,FaderandEQ.

USB Charging Port

Audio 

BASS VOLUME TREBLE BALANCE FADER EQ

XD1225 OPERATION

Menu Function Options Action

Loudness Curve

LOUD OFF Disables the loudness function.

LOUD ONEnables the loudness function. Activating this feature willenhancethebassandtreblefrequencieswhenlistening to music at low volumes.

TunerFrequency

Spacing

FRE USAPrograms the unit to USA tuner spacing.(200kHzforFMand10kHzforAM).(Tuner mode only)

FRE EUPrograms the unit to European tuner spacing.(50kHzforFMand9kHzforAM).(Tuner mode only)

Local/Distance Tuning

LOC OFF Activates distance tuning.LOC ON Activates local tuning for strong station reception only.

Clock Display

CLOC ONProgramsunittodisplaytheclockwhenthepowerisoff.

CLOC OFFProgramsunittonotdisplaytheclockwhenthepoweris off.

Beep Confirmation

BEEP OFF Disables the confirmation beep.BEEP ON Enables the confirmation beep.

General OperationPress and hold AUDIO/MENU for more than 3 seconds to access the setup menu, then press AUDIO/MENU to cycle through menu options. When desired option appears in the display, rotate the volume knobleft/righttoadjustoractivatethe desired function.

Setup Menu

7

Audio OperationPress AUDIO until BAS appearsRotate the volume knobleft/righttoadjust(-6minimum/6maximum)

Press AUDIOuntilTREappearsRotate the volume knobleft/righttoadjust(-6minimum/6maximum)

Press AUDIO until BAL appearsRotate the volume knobleft/righttoadjust(LF12-RT12)"BALL=R"representsequalbalance.

Press AUDIO until FAD appearsRotate the volume knobleft/righttoadjust(FR12-RR12)"FADR=F"representsequalbalance.

Press AUDIOuntilEQappears.Rotatevolumeknobleft/righttoadjustbetweenCLS,POP,ROCandOFF(default)equalizationcurves.AnyadjustmenttotheBassorTreblesettingsautomaticallycancelsthecurrentEQcurve.

Press TUNE nn or TUNE ll for more than 2 seconds to seektothenextstrongstation.

Press TUNE nn or TUNE ll momentarily to change the radiofrequencyupordownonestepatatime.Pressandholdtoadvancequickly.

Press BAND for more than 2 seconds to select mono or stereo(default)receptionofthebroadcastsignal.

Press BANDtoselectbetweenFM1,FM2,FM3andAM1,AM2bands.

Upto18FMstationsand12AMstationscanbestored.Tostoreastation,selectthedesiredbandandstation.Press and hold the desired preset button for more than 2 seconds. When stored, the preset number will appear in the display.Thestationcanberecalledanytimebypressingthecorresponding preset button.

Bass

Treble

Balance

Fader

Preset EQ Curves 

Seek Tuning

Manual Tuning

FM Stereo/Mono 

Band

Storing and Recalling  Station Presets

XD1225 OPERATION

Tuner Operation

8

CD Player OperationWiththelabelfacingup,insertastandardsizeCDintotheCDslot.TheCDwillautomaticallybeginplayback.

Press the EJECTbuttontostopandejecttheCD.Theunitwillchangetotunermode.

Press TRACK lltoskiptothebeginningofthenexttrack.Press TRACK nn to return to the beginning of the current track.PressingTRACK nnagainskipstothebeginningoftheprevioustrack.

Press and hold TRACK ll or TRACK nn to fast forward orreverseatrack.

Press l/ IItotemporarilystopCDplayback.Press l/ IIagaintoresumeplayback.

Press INTtoplaythefirst10secondsofeachtrack.Press INT to cancel.

Press RPTtocontinuouslyrepeatselectedtrack. Press RPT to cancel.

Press RDMtoplayalltracksinrandomorder.Press RDM again to cancel.

Some CD-Rs and CD-RWs may be incompatible with this unit, depending on media type and recording method.

Note:CD-Rrecordingsessionsmustbeclosed(finalized)forplayback.

Insert CD

Eject CD

Track Select

Fast Forward and Reverse

Pause

Intro

Repeat

Random

CD-R/CD-RW Compatibility

XD1225 OPERATION

9

TroubleshootingProblem Cause Action

Yellow wire not connected or incorrect voltage Red wire not connected or incorrect voltage

Checkconnectionsforpropervoltage(11~16VDC)

Blackwirenotconnected CheckconnectiontogroundFuse blown Replace fuseSpeakerwiresnotconnected CheckconnectionsatspeakersOneormorespeakerwirestouchingeachother or touching chassis ground

Insulateallbarespeakerwiresfromeach other and chassis ground

Yellow or red wire touching chassis ground CheckforpinchedwireSpeakerwirestouchingchassisground CheckforpinchedwireIncorrect fuse rating Use fuse with correct ratingUnit is not mounted correctly

CD mechanism position out of alignment

CD transit screws still in place

Checkmountingsleeveoraddabackstrapsupport

Physicaldefectinmedia(CD,CD-RorCD-RW) Checkmediaforscratches

Press EJECT for 3 seconds to resetCD mechanism position Remove 2 transit screws located on top of the unit.

Unit will not turn on(nopower)

Unit has power (butnosound)

Unit blows fuses

Excessiveskipping

Unit will not accepta disc

Error CodesError Code Cause Action

ER-1appearsondisplay Disc error PressejectorRESET

ER-2 appears on display Mechanism error or disc is in upside down PressejectorRESET

ER-3 appears on display Servo error PressejectorRESET

XD1225 OPERATION

10

Limited One Year Warranty

Thiswarrantygivesyouspecificlegalrights. You may also have other rights which vary from state to state.

Dual Electronics Corp. warrants this product to the original purchaser to be free fromdefectsinmaterialandworkmanshipfor a period of one year from the date of the original purchase.

Dual Electronics Corp. agrees, at our option, during the warranty period, to repair any defect in material or workmanshiportofurnishanequalnew, renewed or comparable product (whicheverisdeemednecessary)inexchangewithoutcharges,subjecttoverification of the defect or malfunction and proofofthedateofpurchase.Subsequentreplacement products are warranted for the balance of the original warranty period.

Who is covered?Thiswarrantyisextendedto the original retail purchaser for products purchasedfromanauthorizedDualdealerand used in the U.S.A.

What is covered?Thiswarrantycoversalldefectsinmaterialandworkmanshipinthisproduct.Thefollowingarenotcovered:software, installation/removal costs, damage resulting from accident, misuse, abuse, neglect, product modification, improper installation, incorrect line voltage,unauthorizedrepairorfailureto follow instructions supplied with the product, or damage occurring during return shipment of the product. Specific license conditions and copyright notices for the software can be found via www.dualav.com.

What to do? 1.Beforeyoucallforservice,checkthe

troubleshooting guide in your owner’s manual.Aslightadjustmentofanycustom controls may save you a service call.

2.Ifyourequireserviceduringthewarranty period, you must carefully packtheproduct(preferablyintheoriginalpackage)andshipitbyprepaidtransportation with a copy of the original receipt from the retailer to an authorizedservicecenter.

3. Please describe your problem in writing and include your name, a returnUPSshippingaddress(P.O.Boxnot acceptable), and a daytime phone number with your shipment.

4. For more information and for the locationofthenearestauthorizedservice center please contact us by one ofthefollowingmethods:

•Callustoll-freeat1-866-382-5476•E-mailusatcs@dualav.com

ExclusionofCertainDamages:Thiswarranty is exclusive and in lieu of any and all other warranties, expressed or implied, including without limitation the implied warranties of merchantability and fitness for a particular purpose and any obligation, liability, right, claim or remedy in contract or tort, whether or not arising from the company’s negligence, actual or imputed. No person or representative isauthorizedtoassumeforthecompanyany other liability in connection with the sale of this product. In no event shall the company be liable for indirect, incidental or consequentialdamages.

XD1225 WARRANTY

11

XD1225 OPERATION

FCC ComplianceThisdevicecomplieswithPart15oftheFCCRules.Operationissubjecttothefollowingtwoconditions:

(1)thisdevicemaynotcauseharmfulinterference,and

(2)thisdevicemustacceptanyinterferencereceived,includinginterferencethatmaycause undesired operation. Warning:Changesormodificationstothisunitnotexpresslyapprovedbythepartyresponsibleforcompliancecouldvoidtheuser’sauthoritytooperatetheequipment.

Note:ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforaClassBdigitaldevice,pursuanttoPart15oftheFCCRules.Theselimitsaredesignedtoprovidereasonableprotectionagainstharmfulinterferenceinaresidentialinstallation.Thisequipmentgenerates,usesandcanradiateradiofrequencyenergyand,ifnotinstalledand used in accordance with the instructions, may cause harmful interference to radio communications.However,thereisnoguaranteethatinterferencewillnotoccurinaparticularinstallation.Ifthisequipmentdoescauseharmfulinterferencetoradioortelevisionreception,whichcanbedeterminedbyturningtheequipmentoffandon,theuser is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.•

Increasetheseparationbetweentheequipmentandreceiver.•

Connecttheequipmentintoanoutletonacircuitdifferentfromthattowhichthe•receiver is connected.

Consultthedealeroranexperiencedradio/TVtechnicianforhelp.•

Specifications Frequencyresponse:20Hz-20kHzChannelseparation@1kHz:>65dBD/Aconverter:1 Bit

Tuningrange:87.5MHz-107.9MHzUsablesensitivity:12dBf50dBquietingsensitivity:16dBfStereoseparation@1kHz:40dBFrequencyresponse:30Hz-13kHz

Tuningrange:530kHz-1710kHzUsablesensitivity:30uVFrequencyresponse: 80Hz-2kHz

Speakeroutputimpedance: 4~8 ohmsFuse:5 amp AGCDimensions:7" x 7" x 2" (178 x 178 x 51 mm)

Designandspecificationssubjecttochangewithoutnotice.

CD Player

FMTuner

AMTuner

General

CEA-2006 Power Standard Specifications(reference:14.4VDC+/-0.2V,20Hz~20kHz)

PowerOutput:5WattsRMSx4channelsat4ohmsand<1%THD+NSignaltonoiseratio:75dBA(reference:1wattinto4ohms)

Dual Electronics Corp.TollFree:1-866-382-5476

www.dualav.com©2010DualElectronicsCorp.Allrightsreserved.

NSA0710-V02