YARDAGE CHARTSorders.andersonfabrics.com/LaborCatalogOrders/... · Hourglass Draperies 14 Single Layer Box pleat valance 29 Tapered Valances 66 ... CCESSORY CHARTS. ANDERSON FABRIC

YARDDAGGE CCHAARTTS

ANDERSON FABRIC WORKROOM TABLE OF CONTENTS

YC# YC# YC#

ACCESSORIES DRAPERIES/VALANCES CONT'D TOP TREATMENTS CONT'D

Bolsters 1 Scalloped Top - 118" fabric Erin Valance 40

Chair Cushions 2 Pleated, Rodpocket, Tack Strip 15 Five Finger Bell Valance 41

Bench Cushions 3 Shirred Decorative Tape Tops 15 Flat, Sculpted Valance 42

Futon Covers 3 Shirred on Tack Strip 15 Flat, Soft Valance 42

Pillows 4 Tab/Tie, Narrow Inv. Box plts 15 Fremont Valance 43

Placemats 5 Tab or Tie, Wide Inv. Box plts 15 Grand Pleated Scallop Valance 44

Sink Skirts 6 Dynasty Panels 16 Harrison Valance 45

Tablecloths, Runners 7 Flip Over Panels 17 McCann I, McCann II Valances 45

Tiebacks, Rosettes, Knots 8 Kiana Draperies 18 Hilary Valances 46

Upholstered Folding Screens 9 Pouf Top Panels 19 Jeanine Valance 47

Benches & Ottomans 10 Jeannette Valance 47

Storage trunks 11 Kerchief Valances 48

Dome Trunk, Storage Stool 12 TOP TREATMENTS Loralynn Valance 49

Abilene Valance 20 Open Capri Valance 50

Cascade Valance 21 Pettipouf Valance 51

DRAPERIES/VALANCES Americana, Americana II 22 Picadilly Valance 52

Draped Hdg w/Hooks or Rings 13 Camry, Camry II 22 Pouf Bottom Bell 53

Draped Heading W/Tabs 13 Ashbury Valance/Chantilly Valance 23 Princess Valance 54

Draped Heading W/Ties 13 Awning Valances 24 Hanky Valance 54

Flat Panels W/Hooks/Rings 13 Benton Valance 25 Rodsleeves & Open Ended 55

Grommet Top Panels 13 Canterbury Valance 25 Rushmore Valance 56

Scalloped Top Flat Panels 13 Palais Valance 25 Savannah Valance 57

Shower Curtains 13 Saxony Valance 25 Shaped & Expanse Valances 58

Tab top, Regular, with fullness 13 Winston Valance 25 Sheffield Valance/Camille Valance59

Tab top, Flat, no fullness 13 Benton with contrast inserts 26 Sherin Valance 60

Tie Top, Regular, with fullness 13 Benton with Tent Flaps & Buttons 26 Soft Elegance Valance 61

Angle Top and Arch Top 14 Beverly Valance 27 Sunbursts 62

with Shirring Tape Single Box pleat valance 28 Tab Valance with

Bishop Sleeve Rodpockets 14 Double Box pleat valance 28 Inverted Box Pleats 65

Hourglass Draperies 14 Single Layer Box pleat valance 29 Tapered Valances 66

Inverted French Pleats 14 Double Layer Box pleat valance 29 Teardrop Valance 67

Pinch Pleats 14 Tapered, Single Layer box plt 29 Tent Flaps 68

Rodpockets 14 Capri Valance 30 Vanessa Valance 69

Scalloped Top - Pleated 14 French Pick Up Valance 30 Victoria Valance 70

Shirred Top Tapes 14 Kings & Queens Valance 30 Whimsey Valance 71

Tab top, Box pleated 14 Kings Creation Valance 30 Wilson Valance 72

Angle Top and Arch Top Kingston & Queenston Valance 30

Pleated, Rodpocket, Tack Strip 15 Open Kingston & Queenston Valance 30

Butterfly Pleats 15 Rodpocket Kingston 30

Cartridge Pleats 15 Carolina Valance 32

Cluster Pleats 15 Charleston Valance 33

Flemish Pleats 15 Christina Valance 34

Goblet Pleats 15 Confederate Valance 35

Inverted Box Pleats with Tacking Strip15 Country Elegance Valance 36

Inverted Box Pleats with Hooks/Rings 15 Country Elegance II Valance 36

Pleated Draped Headings 15 Diana & Belle Valance 37

Dixie Valance 38

Gathered English Crown Valance 39

Pleated English Crown Valance 39

TABLE OF CONTENTS

TC1, July 2010

A

ACCCESSORRY CHHARRTSS

ANDERSON FABRIC WORKROOM ACCESSORIES & TRIMS

C.O.M. YARDAGE REQUIREMENTDiameter of Bolster > 6" 8" 10" 15" 10" 12" WEDGE**

Length of Bolster \/ Bed Roll Bed Roll 12 3/4x12x5x9

Bolster BolsterUp to 12" length (0) 1.00 1.25 1.50 2.00 3.00 3.50 1.75

18" (0) 1.00 1.25 1.50 2.00 3.00 3.50 1.7524" (0) 1.00 1.25 1.50 2.00 5.75 6.75 1.7530" (0) 1.00 1.25 1.50 2.00 5.75 6.75 1.7536" (0) 1.00 1.25 1.50 2.00 5.75 6.75 1.7542" (0) 1.00 1.25 1.50 2.00 5.75 6.75 1.7548" (0) 1.00 1.25 1.50 2.00 5.75 6.75 1.7554" (1) 1.50 2.00 2.50 3.50 11.25 13.50 3.0060" (1) 1.50 2.00 2.50 3.50 11.25 13.50 3.0066" (1) 1.50 2.00 2.50 3.50 11.25 13.50 3.0072" (1) 1.50 2.00 2.50 3.50 11.25 13.50 3.0078" (1) 1.50 2.00 2.50 3.50 11.25 13.50 3.00

Shirred Ends (0) 0.50 0.50 0.50 0.50Tootsie Roll Ends (0) 1.00 1.00 1.00 1.501/8", 1/4" or 3/8" Cording 0.50 0.50 0.50 0.50 0.501/2" or 1" Jumbo Cording 0.50 0.50 0.50 0.50 0.501" Shirred Cord 0.50 0.50 0.75 1.00 0.75Up to 5" Self-Lined Ruffling 0.75 1.00 1.25 1.75 1.25Shirred Ends 0.50 0.50 0.50 0.50 N/A

Extras on

bolster ends only.

ACCESSORIESC.O.M. YARDAGE REQUIREMENTS FOR BOLSTERS

YC1, July 2010


Width > Fabric 1/4" or 3/8" C.O.M. Shirred Up to 5" Up tp 5"

CUSHION STYLES \/ Yardage Cording Trim Boxing Buttons Ruffling Pleated

Ruffle

Knife Edge Cushions 0.50 0.25 1.75 0.25 1.00 1.25

Box Edge Cushions 0.75 0.50 3.50 0.50 0.25 1.00 1.25

Width > Box Edge 1/4" or 3/8" C.O.M.

Length \/ Up to 24" Wide Cording Trim

Up to 24" (1) 2.25 0.50 4.50

30" (1) 2.25 0.50 5.00

36" (1) 2.25 0.50 5.50

42" (1) 2.25 0.50 5.50

48" (1) 2.25 0.50 6.00

54" (1) 4.00 0.50 6.50

60" (3) 4.00 0.50 6.50

66" (3) 4.00 0.50 7.00

72" (3) 4.00 0.50 7.50

78" (3) 4.00 0.50 7.50

84" (3) 4.00 0.50 8.00

90" (3) 4.00 0.50 8.50

96" (3) 4.00 0.75 8.50

54" SOLID FABRICS have been used for all yardage estimates. For repeats, multiply your repeat size

times the number in parenthesis, divide by 36, and add this amount to the yardage from the chart.

Overages may be possible. Please call if you would like assistance.

ACCESSORIES

CHAIR PADS & FITTED CUSHIONS

C.O.M. YARDAGE REQUIREMENTS FOR CUSHIONS

WATERFALL FITTED CUSHIONS

YC2, July 2010


Width > Knife Edge 1/4" or 3/8" C.O.M. Box Edge 1/4" or 3/8" C.O.M. Shirred

Length \/ Up to 24" Wide Cording Trim Up to 24" Cording Trim Boxing

Up to 24" (1) 1.75 0.50 2.75 1.75 0.50 5.50 0.75

30" (1) 1.75 0.50 3.25 1.75 0.50 6.25 0.75

36" (1) 1.75 0.50 3.50 1.75 0.50 6.75 0.75

42" (1) 1.75 0.50 3.75 1.75 0.50 7.50 1.00

48" (1) 1.75 0.50 4.25 1.75 0.75 8.25 1.00

54" (1) 3.50 0.50 4.50 3.50 0.75 8.75 1.00

60" (3) 3.50 0.50 4.75 3.50 0.75 9.50 1.00

66" (3) 3.50 0.50 5.25 3.50 0.75 10.25 1.25

72" (3) 3.50 0.50 5.50 3.50 0.75 10.75 1.25

78" (3) 3.50 0.50 5.75 3.50 0.75 11.50 1.25

84" (3) 3.50 0.50 6.25 3.50 1.00 12.25 1.50

90" (3) 3.50 0.50 6.50 3.50 1.00 12.75 1.50

96" (3) 3.50 0.50 6.75 3.50 1.00 13.50 1.50

KNIFE EDGE BOX EDGE up to 5"

Standard Futon Cushion Covers - Fabric Cording Ruffling

Yardage Yardage Yardage

TWIN & FULL Plain edge 10.75

Twin 39" x 75" 1/4" or 3/8" Cord 10.75 0.50

Full 54" x 75" 1/2" or 1" Cord 10.75 1.00

(3) 1" Shirred Cord 10.75 2.75

C.O.M.. Trim 10.75 8.25Ruffling 10.75 4.50

QUEEN & KING Plain edge 11.25Queen 60" x 80" 1/4" or 3/8" Cord 11.25 0.75

King 78" x 80" 1/2" or 1" Cord 11.25 1.50

(3) 1" Shirred Cord 11.25 3.25C.O.M.. Trim 11.25 9.75Ruffling 11.25 5.25

54" SOLID FABRICS have been used for all yardage estimates. For repeats, multiply your repeat size

times the number in parenthesis, divide by 36, and add this amount to the yardage from the chart.


ACCESSORIES

BENCH CUSHIONS

FUTON CUSHION COVERS

C.O.M. YARDAGE REQUIREMENTS FOR BENCH CUSHIONS & FUTON COVERS

Trim Yardage

YC3, July 2010


SQUARE ROUND SQUARE ROUND

14" PILLOW COVER 0.50 0.50 22" PILLOW COVER 0.75 0.75

1/4" or 3/8" Cord 0.50 0.50 1/4" or 3/8" Cord 0.50 0.50

1/2" or 1" Jumbo Cord 0.50 0.50 1/2" or 1" Jumbo Cord 0.50 0.50

1" Shirred Cord 0.75 0.50 1" Shirred Cord 1.00 0.75Premade Trim 1.75 1.50 Premade Trim 2.75 2.25

Up to 5" Self-Lined Ruffle 1.00 1.00 Up to 5" Self-Lined Ruffle 1.75 1.25


1/4" or 3/8" Cord 0.50 0.50 1/4" or 3/8" Cord 0.50 0.50


1" Shirred Cord 0.75 0.50 1" Shirred Cord 1.00 0.75

Premade Trim 2.00 1.50 Premade Trim 2.75 2.25


18" PILLOW COVER 0.75 0.75 26"PILLOW COVER 1.00 1.00

1/4" or 3/8" Cord 0.50 0.50 1/4" or 3/8" Cord 0.50 0.50






1/4" or 3/8" Cord 0.50 0.50 1/4" or 3/8" Cord 0.50 0.50





RECT. PILLOW SIZE 12" x 20" 12" x 22" 14" x 18 14" x 24" 16" x 20"

Pillow cover yardage 0.75 0.75 0.75 0.75 0.75

1/4" or 3/8" Cord 0.50 0.50 0.50 0.50 0.50

1/2" or 1" Jumbo Cord 0.50 0.50 0.50 0.50 0.50

1" Shirred Cord 0.75 0.75 0.75 1.00 1.00

Premade Trim 2.00 2.25 2.00 2.50 2.25

Up to 5" Self-Lined Ruffle 1.50 1.50 1.50 1.50 1.50

BEACH BALL Yardage ENVELOPE Yardage SHIRRED SUNBURST Yardage

10" diameter 1.00 14" to 20" 1.25 Up to 16"diameter 0.75

12" diameter 1.25 22" to 26" 1.75 Cording 0.5

15" diameter 1.50 28" to 30" 2.5 Premade Trim 1.75

KNOTTED CORDED CORNERS W/CORDING (square pillows)

Allow 20" for each corner for knots, plus an allowance for 1/2" cording around the edge of pillow.

On all knotted corded corners style, will come standard with turkish corners. (Included)

SQUARE KNOT, HOURGLASS or BOW OVERLAYS:Allow 1 yard per overlay per pillow.

ACCESSORIESC.O.M. YARDAGE REQUIREMENTS FOR PILLOWS

YC4 July 2010


Unquilted lined w/regular lining 3/4 yard = 2 placemats

Unquilted self-lined 3/4 yard = 1 placemat

**Quilted lined w/regular lining 3/4 yard = 2 placemats

**Quilted self-lined 3/4 yard = 1 placemat

Ruffling: 1/2 yard per placemat

Cording: 3/4 yard = 3 placemats

Bias Banding: 3/4 yard = 3 placemats

Premade Trim 2 yards per placemat

Napkin Allowance:Napkin size + 1/2" work = cut width and length.

Napkin rings:

(Shirred on elastic with velcroed ends.)Allowance: 1 yard will yield 12 napkin rings.

ACCESSORIES

C.O.M. YARDAGE REQUIREMENT -- PLACEMATS

C.O.M. YARDAGE REQUIREMENTS FOR PLACEMATS, NAPKINS & NAPKIN RINGS

C.O.M. YARDAGE REQUIREMENT -- NAPKINS & NAPKIN RINGS

YC5, July 2010


ALLOWANCES:Width: Finished width (measurement around sink) x 3 fullness divided by fabric width = # cuts needed

Length: Finished length + 4" (2" dble hem) + 6" work (+ dble heading, dble pocket on rodpocket style) = cut length

1.5 2 3 4 5 6 7(1 ) (1 ) (2 ) (3 ) (4 ) (5 ) (6 )3.50 3.50 5.50 7.00 9.00 10.50 12.50

3.00 3.00 4.50 6.00 7.50 9.00 10.50

3.25 3.25 4.75 6.25 8.00 9.50 11.00

3.25 3.25 4.75 6.25 8.00 9.50 11.00

Rodpocket style - yardage based on 2" header and 3 1/2" rodpocket.

54" SOLID FABRICS have been used for all yardage estimates. For repeats, multiply your repeat size times the number in parenthesis, divide by 36, and add this amount to the yardage from the chart. Overages may

be possible. Please call if you would like assistance.

DECORATIVE TAPE TOP

BOX PLEATED

ACCESSORIES

Number of WIDTHS

C.O.M. YARDAGE REQUIREMENTS FOR SINK SKIRTS

Finished length up to 42"

RODPOCKET

GATHERED ON TACK STRIP

YC6, July 2010


Round Tablecloths

Diameter x 3.14 divided by 36 = billing yardage for all extras (round up to nearest 1/2 yard)

Square Tablecloths or Overlays

Square measurement x 4 divided by 36 = billing yardage for all extras.

Rectangle, Oval Tablecloths, or Decorative Throws

(Finished width x 2) + (Finished length x 2) divided by 36 = billing yardage for all extras.

Round or Oval Diameter Diameter Diameter

Tablecloths Up to 54" 54 1/4" to 72" 72 1/4" to 92"

Face Fabric 3.25 4.50 5.50

1/4" or 3/8" Cording 0.50 0.50 0.75

1/2" or 1" Jumbo Cording 0.75 1.00 1.25

1" Shirred Cording 1.75 2.25 2.75

Premade Trim/Fringe 5.00 6.50 8.50

Up to 5" Single Ruffling 1.25 1.75 2.25

Up to 5" Self-Lined Ruffling 2.50 3.50 4.50

Square, Rectangle, & Overlay OVERLAY

Tablecloths Up to 36" 36 1/4" to 54" 54 1/4" to 72" 72 1/4" to 92"

Face Fabric 1.25 3 1/4 4 1/4 5 1/4

1/4" or 3/8" Cording 0.50 0.50 0.75 0.75

1/2" or 1" Jumbo Cording 0.75 1.00 1.25 1.50

1" Shirred Cording 1.50 2.00 2.75 3.50

Premade Trim/Fringe 4.25 6.25 8.25 10.50

Up to 5" Single Ruffling 1.25 1.75 2.25 2.75

Up to 5" Self-Lined Ruffling 2.25 3.25 4.50 5.50

Table Runners Up to 36" 36 1/4" to 54" 54 1/4" to 72" 72 1/4" to 92"

Face Fabric (allows for self-lining) 1.25 1.75 2.25 2.75

1/4" or 3/8" Cording 0.50 0.50 0.50 0.50

1/2" or 1" Jumbo Cording 0.50 0.75 0.75 1.00

1" Shirred Cording 1.25 1.50 1.75 2.25

Premade Trim/Fringe 3.50 4.50 5.50 6.50

Up to 5" Single Ruffling 1.00 1.25 1.50 1.75

Up to 5" Self-Lined Ruffling 2.00 2.50 3.00 3.50



C.O.M. YARDAGE REQUIREMENTS FOR TABLECLOTHS, OVERLAYS, & TABLERUNNERS

EXTRAS YARDAGE REQUIREMENT

SQUARE & RECTANGLE

ACCESSORIES

YC7, July 2010


6" Diameter Rosette/Knot up to 80" window. 8" Diameter Rosette/Knot over 80" window.

Allowance: Allowance:Rosette: Up to 4" diameter - 1/2 yard per rosette. Fabric Knots; 1/2 yard per knot (1/2 width wide x 36" cut length.) 5" to 10" diameter - 1 yard for first rosette, 1/2 yard per each additional rosette.

ALLOWANCES:Tieback width x 3 = cut length.Tieback length + 2" = cut width divided by fabric width = # cuts needed per tieback (round up) # cuts needed x cut length divided by 36 = yardage estimate. (round up to 1/4 yard)

Up to 46" width 46" to 71" width Over 71" widthYARDAGE YARDAGE YARDAGE

BOW - Premade, Straight, Tapered Ends 2.00 2.50 3.00BOW - Untied, No Crinoline, Tapered Ends 0.75 1.00 1.50BRAIDED - With Cording 1.50 2.00 2.50DOUBLE JUMBO CORD 0.75 1.00 2.00SINGLE JUMBO CORD 0.50 0.75 1.25RUFFLE - Single 1.25 1.75 2.50 - Self-Lined 1.75 2.00 3.00 - Double; Top & Bottom, Self-Lined 2.00 3.00 3.50SHAPED 1.50 2.00 2.50SHAPED W/CORDING TOP & BOTTOM 2.00 2.50 3.00SHIRRED ON CRINOLINE - Without Heading 1.50 2.25 2.50 - Heading Top & Bottom 1.75 2.50 3.00 - Cording Top & Bottom 1.25 1.75 2.00SHIRRED ON DOUBLE JUMBO CORD - Heading Top & Bottom 1.75 2.25 2.75SHIRRED ON JUMBO CORD 1.50 2.00 2.50SHOESTRING 0.25 0.50 0.50STRAIGHT 0.75 1.25 1.50Straight with Cording Top & Bottom 1.25 2.25 2.50Straight with Tucks 0.75 1.25 1.50Straight with Tapered Ends (with pellon) 0.75 1.25 1.50Straight with 3/5" horizontal Pleats (5" tieback) 1.25 1.75 2.25Straight with Rosettes 1.00 1.25 1.50

54" SOLID FABRICS have been used for all yardage estimates. Yardages do not allow for repeats. Please call for assistance.

ACCESSORIES

C.O.M. YARDAGE REQUIREMENTS - TIEBACKS PER PAIR

C.O.M. YARDAGE REQUIREMENTS FOR TIEBACKS, ROSETTES & KNOTS

YC8, July 2010


STRAIGHT SCALLOPED ARCHED ARCHED-SCALLOPED

STANDARD PANEL SIZES: 14" wide x 58" long 14" wide x 78" long

Please specify size. 18" wide x 58" long 18" wide x 78" long

ALLOWANCES:

Width: Prints: Allow 1 width per panel (front)

Allow 1 width per panel (back)

Width: Solids: Allow 1/2 width per panel (front)

Allow 1/2 width per panel (back)

Length: Finished length + 6" = cut length each panel

SOLID FABRICSPanel Size 14" x 58" 14" x 78" 18" x 58" 18" x 78"

Yardage 5.50 7.00 5.50 7.00

PRINT FABRICSPanel Size 14" x 58" 14" x 78" 18" x 58" 18" x 78"

(5) (5) (5) (5)Yardage 10.75 14.00 10.75 14.00



ACCESSORIESC.O.M. YARDAGE REQUIREMENTS FOR UPHOLSTERED

FOLDING SCREENS

YC9, July 2010


BENCHES:Rectangle Bench w/out Skirt3" x 3" square covered legs (17" High x 15" deep x 30" wide)4" foam seat, which rests on a 3 1/2" seat base.Trimmed with 1/4" Cording below cushion and seat base. Total Yardage Required: 5 yards

Tuxedo Bench w/out skirt (21" High x 18" deep)Twin size 36" wideFull size 52" wideKing size 72" wide (may have to ship truck)Upholstered Bench with springs in seat area.Trimmed with 1/4" cording on seat only.

Shaped Bench (17" High x 31" Wide x 17" Deep)5" wide shirring front and back, trimmed with 1/4" cordingFor Contrast Shirring or cording, deduct thefollowing from the Total Yardage Required and allow the followingin Contrast Fabrics: 2 1/4 yards Shirred Sides or 1 yard CordingTotal Yardage Required: 7 yards

OTTOMANS:Round Ottoman with Box Pleated Skirt(30" Diameter x 17" High)with 4" foam seat and box pleated skirt. Trimmed with 1/4"Cording below cushion. Casters are EXTRA. Caster are 3 1/4" high.Total Yardage Required: 5 1/2 yards

Round Ottoman with Gathered Skirt(30" Diameter x 17" High)4" foam seat and gathered skirt.Trimmed with 1/4" Cording below cushion.Caster are EXTRA. Casters are 3 1/4" high.Total Yardage Required: 6 yards

Square Ottoman with Tailored Skirt(30" Wide x 30" Long x 17" High)with 3" x 3" square covered legs, 4" foam seat and tailored skirt.Trimmed with 1/4" Cording on top of seat and below cushion.Caster are EXTRA. Casters are 3 1/4" high.Total Yardage Required: 5 1/2 yardsPlease specify if Box Pleated skirt is wanted

Square Ottoman without Skirt(30" Wide x 30" Long x 17" High)with 3" x 3" square covered legs, 4" foam seat.Trimmed with 1/4" Cording below cushion and at top of legs.Total Yardage Required: 5 1/2 yards

ACCESSORIESC.O.M. YARDAGE REQUIREMENTS FOR UPHOLSTERED

BENCHES & OTTOMANS

YC10, July 2010


Upholstered chest with hinged cover. Inside is lined with white plastic, coated hardboard.

Skirts are standardly lined at no additional charge.STANDARD DIMENSIONS: 58" wide x 18" Deep x 17" High

FLAT PADDED TOP W/PADDED SIDES:

2" foam seat (knife edge) (pictured) or 4" foam seat (boxed edge) must be specified.

Boxed edge seat is trimmed with 1/4" or 3/8" cording at top and bottom of boxing.

Both styles have cording down sides.

ALLOWANCES:

7 yards

FLAT PADDED TOP WITH SHIRRED SIDES:2" foam seat (knife edge) (pictured) or 4" foam seat (boxed edge) must be specified.

Seat is trimmed with 1/4" or 3/8". Cording at top and bottom of boxing.

ALLOWANCES:

9 yards

STORAGE TRUNKS WITH 4" FOAM (Bench Seat):4" foam seat (boxed edge) is standard.

Seat is trimmed with 1/4" or 3/8" cording at top and bottom of boxing.

Specify if shirred skirt or box pleated skirt is wanted

ALLOWANCES:

Shirred Skirt - 7 1/2 yards

Box Pleated Skirt - 9 yards

ACCESSORIESC.O.M. YARDAGE REQUIREMENTS FOR UPHOLSTERED STORAGE

TRUNKS

YC11, July 2010


Call for Estimate if different sizes than standard are needed.

Dome Top Trunks

(36" Long x 18" Deep x 21" High) (13 1/2" base and 7 1/2" Dome)

Base is lined with white, plastic-coated hardboard. Cover is lined with lining

Trimmed with 1/4" or 3/8" Cording at top, corners of base & on outer edges of dome top.

Top is trimmed with 3" wide straps & handles.

Bow is EXTRA. (EX1401A)

Total Yardage Required: 6 1/2 yards

For Contrast Banding or Cording deduct the following from the

Total Yardage Required and allow the following in Contrast Fabrics:

Straps 1 yard

Cording 1 yard

Box 1 yard

Storage Stools(18" Wide x 18" Long x 14" High)

Upholstered storage stool has a 4" high padded, hinged cover.

Inside is lined with white, plastic-coated hardboard.

Trimmed with 1/4" or 3/8" Cording around top of cover, top of opening & down each corner,

Total Yardage Required: 4 yards

C.O.M. YARDAGE REQUIREMENTS FOR UPHOLSTERED DOME TRUNK & STORAGE STOOLS

ACCESSORIES

YC12, July 2010

D

DRAAPEERIES CHHARRTSS

ANDERSON FABRIC WORKROOM DRAPERIES

With 54" fabric, the following chart has been provided to assist you in figuring the number of widths needed for proper1 1/2 to 2 times fullness. Allowances have been made for an overlap, two 3 1/2" returns and side hems.Usee the rod face (bracket to bracket) measurement to determine the number of widths needed. Always round up to thenearest whole width.

# of Widths 2 3 4 5 6 7 8 9 10Rod Face - 54"

Fabric 24"-44" 45"-71" 72"-98" 99"-125" 126"-152" 153"-179" 180"-206" 207"-233" 234"-260"

This yardage chart is figured with a 4" double top or 10" facing and a 4" double bottom hem. Finished length is given up to 108". When ordering, you MUST give TOTAL finished length, rod size and return size.

# of Widths 2 (1) 3(2) 4(3) 5(4) 6(5) 7(6) 8(7) 9(8) 10(9)

Up to 16" 2.50 3.50 4.50 5.50 6.50 7.50 8.50 9.50 10.50

36" 3.50 5.00 6.50 8.00 9.50 11.50 13.00 14.50 16.00

48" 4.00 6.00 8.00 10.00 11.50 13.50 15.50 17.50 19.50

60" 4.50 7.00 9.00 11.50 13.50 16.00 18.00 20.50 22.50

72" 5.50 8.00 10.50 13.00 15.50 18.50 21.00 23.50 26.00

84" 6.00 9.00 12.00 15.00 17.50 20.50 23.50 26.50 29.50

96" 6.50 10.00 13.00 16.50 19.50 23.00 26.00 29.50 32.50

108" 7.50 11.00 14.50 18.00 21.50 25.00 29.00 32.50 36.00

Tab Yardage 0.50 1.00 1.00 1.50 1.50 2.00 2.00 2.50 2.50

Tie Yardage 0.50 0.50 1.00 1.00 1.00 1.00 1.50 1.50 1.50

10" Facing Ydge 1.00 1.50 2.00 2.50 3.00 3.50 4.00 4.50 5.00

54" SOLID FABRICS have been used for all yardage estimates. For repeats, multiply your repeat size times the number in parenthesis, divide by 36 and add this amount to the yardage listed in the chart. Overages may be possible. Please call if you would like assistance.

C.O.M. YARDAGE REQUIREMENT

DRAPERIESC.O.M. YARDAGE REQUIREMENTS FOR DRAPERIES &

STRAIGHT BOTTOM VALANCES

Yardage amounts on this page are for the following styles @ 1 1/2 to 2 x fullness:

Draped Headings w/Hooks, Rings, Tabs, or Ties, Flat Panels, Scalloped Top Flat Panels, Grommet Tops, Shower Curtains, Tabs w/Fullness, Tie Tops

YC13, July 2010


With 54" fabric, the following chart has been provided to assist you in figuring the number of widths needed for proper2 1/2 times fullness. Allowances have been made for an overlap, two 3 1/2" returns and side hems.Usee the rod face (bracket to bracket) measurement to determine the number of widths needed. Always round up to thenearest whole width.


Fabric 18"-35" 36"-57" 58"-78" 79"-100" 101"-122" 123"-143" 144"-165" 166"-186" 187"-206"

This yardage chart is figured using a 4" double top and a 4" double bottom hem. Finished Length is up to 108". When ordering, you MUST give TOTAL finished length, rod size and return size.

# of Widths 2 (1) 3(2) 4(3) 5(4) 6(5) 7(6) 8(7) 9(8) 10(9)Up to 16" 2.00 3.00 4.00 4.75 5.75 6.75 7.75 8.50 9.50

36" 3.00 4.50 6.00 7.50 9.00 10.50 12.00 13.50 15.0048" 3.75 5.50 7.50 9.25 11.00 13.00 14.75 16.50 18.5060" 4.50 6.50 8.75 11.00 13.00 15.25 17.50 19.50 21.7572" 5.00 7.50 10.00 12.50 15.00 17.50 20.00 22.50 25.0084" 5.75 8.50 11.50 14.25 17.00 20.00 22.75 25.50 28.5096" 6.50 9.50 12.75 16.00 19.00 22.25 25.50 28.50 31.50

108" 7.00 10.50 14.00 17.50 21.00 24.50 28.00 31.50 35.00

Tab Yardage 1.00 1.50 2.00 2.25 2.75 3.25 3.75 4.25 4.50

Tie Yardage 0.50 1.00 1.00 1.50 1.50 2.00 2.00 2.50 2.50





Yardage amounts on this page are for the following styles @ 2 1/2x fullness:

Angle/Arch tops w/Shirring tape, Bishop Sleeve Rodpocket, Hourglass, Inverted French Pleats, Pinch Pleats, Rodpockets, Scalloped Top Pleated, Shirred Top Tapes, Box Pleated Tabs

YC14, July 2010


With 54" fabric, the following chart has been provided to assist you in figuring the number of widths for proper 3x fullness.Allowance has been made for an overlap, two 3 1/2" returns and side hems. Use the rod face (bracket to bracket)measurement to determine the number of widths needed. Always round up to the nearest whole width.

# of Widths 2 3 4 5 6 7 8 9 10

Rod Face - 54" Fabric

16"-29" 30"-47" 48"-65" 66"-83" 84"-101" 102"-119" 120"-137" 138"-155" 156"-173"

This yardage chart is figured using a 4" double top or 10" facing and a 4" double bottom hem. Finished Length is given up to 108".When ordering, you MUST give TOTAL finished length, rod size and return size.

# of Widths 2 (1) 3(2) 4(3) 5(4) 6(5) 7(6) 8(7) 9(8) 10(9)

Up to 16" 2.00 3.00 4.00 4.75 5.75 6.75 7.75 8.50 9.50

36" 3.00 4.50 6.00 7.50 9.00 10.50 12.00 13.50 15.00

48" 3.75 5.50 7.50 9.25 11.00 13.00 14.75 16.50 18.50

60" 4.50 6.50 8.75 11.00 13.00 15.25 17.50 19.50 21.75

72" 5.00 7.50 10.00 12.50 15.00 17.50 20.00 22.50 25.00

84" 5.75 8.50 11.50 14.25 17.00 20.00 22.75 25.50 28.50

96" 6.50 9.50 12.75 16.00 19.00 22.25 25.50 28.50 31.50

108" 7.00 10.50 14.00 17.50 21.00 24.50 28.00 31.50 35.00

Tab Yardage 1.00 1.50 2.00 2.25 2.75 3.25 3.75 4.25 4.50

Tie Yardage 0.50 1.00 1.00 1.50 1.50 2.00 2.00 2.50 2.50

54" SOLID FABRICS have been used for all yardage estimates. For repeats, multiply your repeat size times the number in parenthesis, divide by 36 and add this amount to the yardage listed in the chart. Overages may be possible.




Yardage amounts on this page are for the following styles @ 3 x fullness:

Angle/Arch top Pleated, Angle/Arch top Rodpocket or Shirred on Tack Strip, Butterfly Pleats, Cartridge Pleats, Cluster Pleats, Flemish Pleats, Goblet Pleats, Inverted Box Pleats,Pleated Draped Heading, Scalloped

Top Pinch Pleats, 118" Sheers for Rodpockets or Pleated, Shirred on Tack Strip, Decorative Shirred Tape Tops, Narrow or Wide Inverted Box Pleats w/Tabs or Ties

YC15, July 2010


ALLOWANCES:Width: Rod face (bracket to bracket) x 1 1/2 - 2 (fullness) + 6"(side hems) divided by width of fabric = # cuts

Length: Finished length - tab length + 8" (bottom hem) + 2" (for work) = cut length

TABS: Standard 8" wide x 8" long. (Usually 2 tab cuts available per width; 1/2 yard per every 2 tabs)

Self or Contrast "scrunchies" are put over tabs. Scrunchies alternate with 2 on every other tab.

SCRUNCHIES: Standardly made 4" wide x 8" long (9" wide x 17" long cuts; allow 1/2 yard per 6 scrunchies)

The following chart has been provided to assist you in figuring the number of widths needed for proper fullness

using 54" fabric. Allowance has been made for 6" side hems. Use the rod face (bracket to bracket) measurement to

determine the number of widths needed. Always round up to the nearest whole width.


Fabric 18"-35" 36"-57" 58"-78" 79"-100" 101"-122" 123"-143" 144"-165" 166"-186" 187"-206"

This yardage chart is figured using a 4" double bottom hem. Finished Length is given up to 108".

When ordering, you MUST give TOTAL finished length, rod size and return size.

# of Widths 2 (1) 3(2) 4(3) 5(4) 6(5) 7(6) 8(7) 9(8) 10(9)Finished Length up

to 36" 2.50 3.50 4.50 5.50 6.50 7.50 8.50 10.00 11.00

42" 2.50 4.00 5.00 6.50 7.50 9.00 10.00 11.00 12.50

48" 3.00 4.50 6.00 7.00 8.50 10.00 11.50 13.00 14.00

54" 3.50 5.00 6.50 8.00 9.50 11.00 12.50 14.50 16.00

60" 3.50 5.50 7.00 9.00 10.50 12.50 14.00 15.50 17.50

66" 4.00 6.00 8.00 9.50 11.50 13.50 15.50 17.50 19.00

72" 4.50 6.50 8.50 10.50 12.50 14.50 16.50 19.00 21.00

78" 4.50 7.00 9.00 11.50 13.50 16.00 18.00 20.00 22.50

84" 5.00 7.50 10.00 12.00 14.50 17.00 19.50 22.00 24.00

90" 5.50 8.00 10.50 13.00 15.50 18.00 20.50 23.50 26.00

96" 5.50 8.50 11.00 14.00 16.50 19.50 22.00 24.50 27.50

102" 6.00 9.00 12.00 14.50 17.50 20.50 23.50 26.50 29.00

108" 6.50 9.50 12.50 15.50 18.50 21.50 24.50 28.00 31.00TAB YARDAGE 3.00 4.50 6.00 7.50 9.00 10.50 12.00 13.50 15.00

SCRUNCHY YDGE 1.50 2.50 3.00 4.00 4.50 5.50 6.00 7.00 7.50


DRAPERIES

Number of WIDTHS in Drapery or Valance

C.OM. YARDAGE REQUIREMENTS FOR DYNASTY PANELS

YC16, July 2010


ALLOWANCES: Width: One fabric width wide (48" or 54").*Two cut lengths are needed - one for the panel and one for the flip over.

Panel Length: PILLOWCASED BOTTOM Finished length of panel (top of pole to desired length) + 4" =cut length. Finished length of flip over (30" standard) + 4" work = cut length.

Panel Length: 4" DOUBLE BOTTOM HEM Finished length of panel (top of pole to desired length) + 8" (4" dble bottom hem) + 4" work = cut length

Flip over: Finished length of flip over (30" standard) + 4" work = cut length.

* Finished Length of PANEL includes the finished length of the FLIP OVERPILLOWCASED HEM 4" DOUBLE HEM

Finished Length \/ Face Fabric Contrast Lining Face Fabric ** Regular LiningUp to 72" 3.25 3.25 3.25 3.25

84" 3.50 3.50 3.50 3.5096" 3.75 3.75 3.75 3.75

108" 4.25 4.25 4.25 4.25120" 4.50 4.50 4.50 4.50

**For a Contrast Flip Over, add 1 yard of contrast fabric and subtract 1 yard from regular lining ydge amount.54" SOLID FABRICS have been used for all yardage estimates. For repeats, multiply your repeat size times the number in parenthesis, divide by 36 and add this amount to the yardage listed in the chart. Overages may be possible. Please call if you would like assistance.

DRAPERIES


C.OM. YARDAGE REQUIREMENTS FOR FLIP OVER PANELS

YC17, July 2010


ALLOWANCES: Width: PANELS; Rod face (bracket to bracket) x 2 (fullness) = total fabric inches needed for PANELS. TRIANGLES; Rod face (bracket to bracket) x 2 (fullness) = total fabric inches needed for TRIANGLES.Length: PANELS; Finished length + 2" (work) = cut length. TRIANGLES; Finished length + 2" (work) = cut length.Panel & Triangle yardages must be added together for total yardage if same fabric used.

# Triangles > 1 2 3 4 5 6 7 8Length up to 108" 2.00 3.00 4.00 5.00 6.00 7.00 9.00 10.00Length up to 116" 2.00 3.00 4.00 5.00 6.00 7.00 9.00 10.00

# Triangles > 1 2 3 4 5 6 7 83.00 3.00 3.00 3.00 3.00 4.00 4.00 4.00

DRAPERIESC.OM. YARDAGE REQUIREMENTS FOR

KIANA DRAPERIES

Length up to 108"The banding yardage requirement chart is based on 54" RailRoaded fabric.

Seamless lightweight or sheer fabrics are recommended for this type of treatment.Always select fabrics that are compatible when sewn together.

The yardage chart below was calculated with 118" fabric.

C.O.M. YARDAGE REQUIREMENT - KIANA DRAPERIES

RAILROADED YARDAGE - 118" wide fabrics will allow a MAXIMUM finished length of 116".

2" BANDING YARDAGE REQUIREMENT

YC18, July 2010


ALLOWANCES: Width: Rod face x 2 (fullness) + returns + 6" (side hems), divided by width of fabric = # of cutsLength: Finished length + 48" pouf allowance + 8" (4" double bottom hem) + 2" (work) = cut length OR Finished length + 48" pouf allowance + 1" pillowcased hem + 2" work = cut length.

The following chart has been provided to assist you in figuring the number of widths needed for proper 2 times fullnessusing 54" fabric. Allowance has been made for two 3 1/2" returns and side hems. Use the rod face (bracket to bracket)measurement to determine the number of widths needed. Always round up to the nearest whole width.

Number of WIDTHS in Drapery or Valance# of Widths 1 2 3 4 5 6 7 8 9

Rod Face - 54" Fabric 24"-44" 45"-71" 72"-98" 99"-125" 126"-152" 153"-179" 180"-206" 207"-233" 234"-260"

This yardage chart is figured using a 40" top fullness allowance; 2" turn under at top and a 4" double bottom hem.Finishd length given is up to 120". When ordering, you MUST giveTOTAL finished length including horizontal folds across top.

# of Widths 1 2 (1) 3(2) 4(3) 5(4) 6(5) 7(6) 8(7) 9(8) 36" 2.50 5.00 7.50 10.00 12.50 15.00 17.50 20.00 22.50 48" 2.75 5.50 8.25 11.00 13.75 16.50 19.25 22.00 24.75 60" 3.25 6.50 9.75 13.00 16.25 19.50 22.75 26.00 29.2572" 3.50 7.00 10.50 14.00 17.50 21.00 24.50 28.00 31.5084" 3.75 7.50 11.25 15.00 18.75 22.50 26.25 30.00 33.7596" 4.25 8.50 12.75 17.00 21.25 25.50 29.75 34.00 38.25

108" 4.50 9.00 13.50 18.00 22.50 27.00 31.50 36.00 40.50120" 4.75 9.50 14.25 19.00 23.75 28.50 33.25 38.00 42.75

54" SOLID FABRICS have been used for all yardage estimates. For repeats, multiply your repeat size times thenumber in parenthesis, divide by 36 and add this amount to the yardage listed in the chart. Overages may be possible. Please call if you would like assistance.

C.OM. YARDAGE REQUIREMENTS FOR POUF TOP PANELS


DRAPERIES

YC19, July 2010

TOOP TCTRECHA

EATART

TMTS

ENT

ANDERSON FABRIC WORKROOM TOP TREATMENTS

ALLOWANCES: Width: (Unlined) Board face + returns x 1 1/2 fullness + 2 1/2" side hems divided by fabric width = # of cuts

Width: (Lined) Board face + returns x 1 1/2 fullness + 5" side hems divided by fabric width = # of cuts

Length: Finished length (mid point) x 3 = cut length; (If sheer or very light weight fabric)

Length: Finished length (mid point) x 2.5 = cut length; (If using regular weight fabric).

# of FEET 2 3 4 5 6 7 8 9 10

Mid Point (0) (1) (1) (1) (2) (2) (2) (3) (3)

Up to 20" 2.00 3.50 3.50 3.50 5.50 5.50 5.50 7.00 7.00

28" 2.50 5.00 5.00 5.00 7.00 7.00 7.00 9.50 9.50

36" 3.00 6.00 6.00 6.00 9.00 9.00 9.00 12.00 12.00

44" 4.00 7.50 7.50 7.50 11.50 11.50 11.50 15.00 15.00

52" 4.50 9.00 9.00 9.00 13.00 13.00 13.00 17.50 17.50

60" 5.00 10.00 10.00 10.00 15.00 15.00 15.00 20.00 20.00

1/4" cord @ top 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50

premade trim @ top 1.00 1.50 1.50 2.00 2.50 2.50 3.00 3.50 3.50

If you wish to have the side legs covered in face fabric, you must specify on your work order and supply

additional yardage. Add 1 yard to the allowances above up to 36" length, 2 yards up to 60" length.

54" SOLID FABRICS have been used for all yardage estimates. For repeats, multiply your repeat size times the number in parenthesis, divide by 36 and add this amount to the yardage listed in the chart. Overages may be possible. Please call if you would like assistance.Possible Truck Freight due to Finished Width of Valance.

TOP TREATMENTSC.O.M YARDAGE REQUIREMENTS FOR ABILENE VALANCE


YC20, July 2010


ALLOWANCES:

Width: Board Face width x 3 (fullness) + 2 returns + 2" divided by the fabric width = # cuts needed.

Length: Finished length (long point) + 5" = cut length.

# of FEET 2 (1) 3 (2) 4 (2) 5 (4) 6 (4) 7 (4) 8 (5) 9 (6) 10 (6)

Long Point Up to 36" 2.50 3.50 3.50 4.50 5.75 5.75 6.75 8.00 8.00

42" 2.75 4.00 4.00 5.25 6.75 6.50 7.75 9.00 9.00

48" 3.00 4.50 4.50 6.00 7.25 7.25 8.75 10.25 10.25

54" 3.25 5.00 5.00 6.50 8.25 8.25 9.75 11.50 11.50

60" 3.75 5.50 5.50 7.25 9.00 9.00 10.75 12.50 12.50

66" 4.00 6.00 6.00 8.00 10.00 10.00 12.00 14.00 14.00

72" 4.50 6.75 6.70 9.00 11.25 11.25 13.50 15.75 15.75

1/4" cord @ top 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50

premade trim @ top 1.00 1.50 1.50 2.00 2.50 2.50 3.00 3.50 3.50

Template hem 1.00 1.00 1.50 2.00 2.00 2.50 2.50 3.00 3.00

FOR TOTAL FABRIC YARDAGE

TOTAL LENGTH Please add your individual yardages for

Up to 12" Valances and Cascading Returns together to get

12 1/4" - 18" your TOTAL FABRIC YARDAGE.

18 1/4" - 24"

If you choose to only use Face Fabric, please double the Face Fabric Yardage for self-lined.

54" SOLID FABRICS have been used for all yardage estimates. For repeats, multiply your repeat size times the

number in parenthesis, divide by 36 and add this amount to the yardage listed in the chart.


0.75

1.00

CENTER JABOTS

0.50

TOP TREATMENTSC.O.M YARDAGE REQUIREMENTS FOR CASCADE VALANCES

C.O.M. YARDAGE REQUIREMENT - VALANCES

JABOT YARDAGE REQUIREMENT

YC21, July 2010


AMERICANA VALANCE AMERICANA II VALANCE

CAMRY II VALANCE

ALLOWANCES:

Width: Board Face width x 3 (fullness) + 2 returns + 2" divided by the fabric width = # cuts needed.

Length: Finished length (long point) + 5" = cut length.

# of FEET 2 (1) 3 (2) 4 (2) 5 (4) 6 (4) 7 (4) 8 (5) 9 (6) 10 (6)

Long Point Up to 36" 2.50 3.50 3.50 4.50 5.75 5.75 6.75 8.00 8.00

42" 2.75 4.00 4.00 5.25 6.75 6.50 7.75 9.00 9.00

48" 3.00 4.50 4.50 6.00 7.25 7.25 8.75 10.25 10.25

54" 3.25 5.00 5.00 6.50 8.25 8.25 9.75 11.50 11.50

60" 3.75 5.50 5.50 7.25 9.00 9.00 10.75 12.50 12.50

66" 4.00 6.00 6.00 8.00 10.00 10.00 12.00 14.00 14.00

72" 4.50 6.75 6.70 9.00 11.25 11.25 13.50 15.75 15.75

1/4" cord @ top 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50

premade trim @ top 1.00 1.50 1.50 2.00 2.50 2.50 3.00 3.50 3.50

Template hem 1.00 1.00 1.50 2.00 2.00 2.50 2.50 3.00 3.00

FOR TOTAL FABRIC YARDAGE

TOTAL LENGTH Please add your individual yardages for

Up to 12" Valances and Cascading Returns together to get

12 1/4" - 18" your TOTAL FABRIC YARDAGE.

18 1/4" - 24"

If you choose to only use Face Fabric, please double the Face Fabric Yardage for self-lined.




0.75

1.00

CENTER JABOTS

0.50

TOP TREATMENTS

C.O.M YARDAGE REQUIREMENTS FOR AMERICANA, AMERICANA II, CAMRY, & CAMRY II VALANCES

C.O.M. YARDAGE REQUIREMENT - VALANCES

JABOT YARDAGE REQUIREMENT

CAMRY VALANCE

YC22, July 2010


ASHBURY VALANCE CHANTILLY VALANCE

ALLOWANCES: Width: Finished width x 3 fullness + 2" side hems, divided by the fabric width = # cuts Length: Finished length + 4" work = cut length.Cording: Number of valance cuts x width of the fabric x 2 divided by 570" bias = cording yardage needed.

The following chart has been provided to assist you in figuring the number of widths needed for proper 2 1/2 times fullness.using 54" fabric. Use the rod face (bracket to bracket) measurement to determine the number of widths needed. Alwaysround up to nearest whole width.

Number of WIDTHS in Valance


Fabric 20" - 34" 35" - 54" 55" - 76" 77" - 98" 99" - 120" 121" - 140" 141" - 162" 163" - 184" 185" - 206"

C.O.M. YARDAGE REQUIREMENT# of Widths > 2 (1) 3(2) 4(3) 5(4) 6(5) 7(6) 8(7) 9(8) 10(9)

FACE FABRIC

Up to 12" FL 1.00 1.50 2.00 2.50 3.00 3.50 4.00 4.50 5.0018" 1.50 2.25 3.00 3.75 4.50 5.25 6.00 6.75 7.5024" 2.00 3.00 4.00 5.00 6.00 7.00 8.00 9.00 10.00

CONTRAST

Length up to 12" 1.00 1.50 2.00 2.50 3.00 3.50 4.00 4.50 5.0018" 1.50 2.25 3.00 3.75 4.50 5.25 6.00 6.75 7.5024" 2.00 3.00 4.00 5.00 6.00 7.00 8.00 9.00 10.00

1/4" Cording 0.50 0.75 1.00 1.00 1.25 1.50 1.75 1.75 2.00Premade trim 6.50 9.50 12.50 15.50 18.50 21.50 24.50 27.50 30.50

For self-lined, please double the Face Yardage.



1/4" Cording Top & Bottom yardage requirement must be added to valance yardage.


C.O.M YARDAGE REQUIREMENTS FOR ASHBURY & CHANTILLY VALANCES

TOP TREATMENTS

YC23, July 2010


RODPOCKET TOP:

Made with Rodpocket at top & bottom. Awning hardware kit is not included.

Please specify pocket size needed at top & bottom.

Valance is standardly made flat, with no fullness. Please specify if the valance is to be shirred.

BOARD MOUNTED:

Board Mounted at top on a standard 2" board with tacking strip & side legs.

Support board attached across the width behind the flap; standardly covered with lining.

Please specify on your work order if side legs & support board are to be covered with face fabric and allow 2 yards fabric.

Valance is standardly made flat, with no fullness.

Cannot be hinged; No Rodpockets.

Specify projection at bottom.

WOOD FRAME:

82" maximum board face width. Cannot be hinged

Please submit estimate for larger sizes.

Complete wooden frame made from 3/8" particle board and covered with lining.

Side legs are included and are standardly covered with lining. Please specify on your work order if the side legs

are to be covered with face fabric and allow 1 extra yard fabric.

Valance attached at top of 2" wide board and hangs loose over frame. (specify projection at bottom.)

Valance is standardly made flat, with no fullness. Please specify if the valance is to be shirred.

ALLOWANCES: ALL STYLESWidth: Face width + 2" divided by fabric width = # cuts needed for front

Return size + 2" divided by fabric width = #cuts for each end piece

Length: Finished length (including flap) + 12" = cut length

With Fullness:

Width: Face width x 2 1/2 fullness divided by fabric width = # cuts needed for front

Return size + 2" divided by fabric width = # cuts each end (normally 1 cut for 2 returns)

RODPOCKET STYLE:

# WIDTHS 2 (1) 3 (2) 4 (3) 5 (4) 6 (5) 7 (6) 8 (7) 9 (8)

Length to 18" 2.00 3.00 4.00 4.75 5.75 6.75 7.75 8.50

Length to 24" 2.25 3.50 4.50 5.75 6.75 8.00 9.00 10.00

BOARD MOUNTED STYLE: (up to 6" bottom projection)

# FEET 2 (0) 3 (0) 4 (0) 5 (1) 6 (1) 7 (1) 8 (2) 9 (2)

Length to 18" 1.00 1.00 1.00 1.75 1.75 1.75 2.75 2.75

Length to 24" 1.25 1.25 1.25 2.25 2.25 2.25 3.25 3.25

WOOD FRAME STYLE: (up to 6" bottom projection)

# FEET 2 (0) 3 (0) 4 (0) 5 (1) 6 (1) 7 (1) 8 (2) 9 (2)

Length to 18" 1.75 1.75 1.75 1.75 1.75 1.75 2.75 2.75

Length to 24" 2.25 2.25 2.25 2.25 2.25 2.25 3.25 3.25

C.O.M YARDAGE REQUIREMENTS FOR AWNING VALANCES

C.O.M. YARDAGE REQUIREMENTS

TOP TREATMENTS

YC24, July 2010


BENTON CANTERBURY PALAIS

SAXONY WINSTON

ALLOWANCES:

Width: Board face x 3 (fullness) + 2" (side hems) divided by fabric width = # cutsLength: Finished length + 4" (2" double bottom hem) (or 1" pillowcased bottom) + 2" tacking strip + 2" (work) = cut length.

CORDING: Board face width + 2 returns divided by 570" bias cording inches = ydge. Est. for cording allowance. (1/4" cording - 1 yard yields 570" bias.)

With 54" fabric, the charts below have been provided to assist you in figuring the number of widths needed for proper fullness.Use the rod face (bracket to bracket) measurement to determine the number of widths needed. Always round up to the nearest whole width.

Width of valance 20"-24" 24 1/4"-36" 36 1/4"-48" 48 1/4"-60" 60 1/4"-72" 72 1/4"-84" 84 1/4"-96" 96 1/4"- 108 1/4"-# of FEET 2 3 4 5 6 7 8 9 10# of Widths 2 3 3 4 5 5 6 7 7

This yardage chart is figured using a 2" bottom hem. Finished Length is given up to 24". Always round up to the nearest 1/4 yard.

# of FEET 2 3 4 5 6 7 8 9 10# of Widths 2 (1) 3(2) 3(2) 4(3) 5(4) 5(4) 6(5) 7(6) 7(6)Finished Length Up to 12" 1.50 2.00 2.00 2.50 3.00 3.00 3.50 4.00 4.00

12 1/4" to 18" 2.00 2.50 2.50 3.50 4.00 4.00 4.50 5.50 5.50

18 1/4" to 24" 2.50 3.00 3.00 4.00 5.00 5.00 5.50 6.50 6.501/4" Cording Across Top 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50Premade Trim Across Top 1.00 1.50 1.50 2.00 2.50 2.50 3.00 3.50 3.5054" SOLID FABRICS have been used for all yardage estimates. For repeats, multiply your repeat size times the number in parenthesis, divide by 36 and add this amount to the yardage listed in the chart. Overages may be possible.



TOP TREATMENTSC.O.M YARDAGE REQUIREMENTS FOR BENTON, PALAIS,

CANTERBURY, SAXONY, & WINSTON VALANCES

YC25, July 2010


Tent Flap style: "B" Button Flap style: "C" Benton w/contrast pleats

ALLOWANCES: Width: FACE FABRIC: Board face x 3 fullness + 2" (side hems) divided by fabric width = # cuts

CONTRAST PLEATS (all styles): Allow 1 cut per 2 contrast insertsBUTTONS: Allow 1/2 yard for buttons on Flaps

Length: Flaps styles: Finished length + 1" pillowcased hem + 2" tacking strip + 2" (work) = cut length.Length: Benton w/contrast pleats: Finished length + 4" (2" double hem) + 2" tacking strip + 2" (work) = cut length.

CORDING: Board face width + 2 returns divided by 570" bias cording inches = ydge. Est. for cording allowance. (1/4" cording - 1 yard yields 570" bias.)

Use this chart to determine the # of contrast inserts needed. There will be one more insert than # spaces. Contrast inserts are also placed in the corners.# SPACES 2 3 4 5 6 7 8 9 10# INSERTS (PLEATS) 3 4 5 6 7 8 9 10 11# BUTTONS 4 6 8 10 12 14 16 18 20

# of FEET 2 3 4 5 6 7 8 9 10# of Widths 1 (0) 2 (1) 2 (1) 2 (1) 2 (1) 3(2) 3(2) 3(2) 3(2)

FACE FABRICFinished Length to 12" 0.50 1.00 1.00 1.00 1.00 1.50 1.50 1.50 1.50

up to 24" 1.00 1.50 1.50 1.50 1.50 2.50 2.50 2.50 2.50

CONTRAST 2 (1) 2 (1) 3(2) 3(2) 4(3) 4(3) 5(4) 5(4) 6(5)Finished Length to 12" 1.00 1.00 1.50 1.50 2.00 2.00 2.50 2.50 3.00

up to 24" 2.00 2.00 2.50 2.50 3.50 3.50 4.50 4.50 5.00

# of FEET 2 3 4 5 6 7 8 9 10# of Widths 2 (1) 2(1) 3(2) 3(2) 4(3) 4(3) 5(4) 5(4) 6(5)

FACE FABRIC

Finished Length to 12" 1.00 1.00 1.50 1.50 2.00 2.00 2.50 2.50 3.00up to 24" 2.00 2.00 2.50 2.50 3.5. 3.50 4.50 4.50 5.00

CONTRAST 1(0) 2(1) 2(1) 2(1) 2(1) 3(2) 3(2) 3(2) 3(2)Finished Length to 12" 0.50 1.00 1.00 1.00 1.00 1.50 1.50 1.50 1.50

up to 24" 1.00 1.50 1.50 1.50 1.50 2.50 2.50 2.50 2.50ALL STYLES:

1/4" Cording @ Top 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50Premade Trim @ Top 1.00 1.50 1.50 2.00 2.50 2.50 3.00 3.50 3.50

C.O.M. YARDAGE REQUIREMENT - BENTON WITH CONTRAST PLEATS

C.O.M. YARDAGE REQUIREMENT - TENT FLAP & BUTTON FLAP

TOP TREATMENTSC.O.M YARDAGE REQUIREMENTS FOR TENT FLAP BENTONS &

BENTONS WITH CONTRAST PLEATS

YC26, July 2010


ALLOWANCES: Width: TOP LAYER: Rod face x 2 1/2 fullness divided by the fabric width + 2" (side hems) = #of cuts needed BOTTOM LAYER: Rod face x 2 1/2 fullness divided by fabric width + 2" (side hems) = # of cuts needed.Length: TOP LAYER: Finished length (Long point) + double heading + double pocket + 2" (for work) = cut length needed BOTTOM LAYER: Finished length (Long point) + 4" work = cut length needed* Double yardage amounts for self-lined.

The following chart has been provided to assist you in figuring the number of widths needed for proper 2 1/2 times fullness using 54" fabric.Use the rod face (bracket to bracket) measurement to determine the number of widths needed. Always round up to thenearest whole width.

# of Widths 2 3 4 5 6 7 8 9 10Rod Face - 54" Fabric 20" - 34" 35" - 54" 55" - 76" 77" - 98" 99" - 120" 121" - 140" 141" - 162" 163" - 184" 185" - 206"

This yardage chart is figured using a 2" Headings, 3 1/2" Pockets and a Pillowcased Hem. Finished Length is given up to 25".Always round up to the nearest 1/4 yard. When ordering, you MUST give TOTAL finished length, rod size, & return size.

# of Widths > 2 (1) 3(2) 4(3) 5(4) 6(5) 7(6) 8(7) 9(8) 10(9)Finished Length

Up to 16" 2 2.5 3.5 4.5 5 6 6.5 7.5 8.525" 2.5 3.5 4.5 5.5 6.5 7.5 8.5 10 11

# of Widths > 2 (1) 3(2) 4(3) 5(4) 6(5) 7(6) 8(7) 9(8) 10(9)Finished Length

Up to 16" 1.5 2 2.5 3.5 4 4.5 5 5.5 6.525" 2 3 3.5 4.5 5.5 6.5 7 8 9


C.O.M. YARDAGE REQUIREMENT TOP LAYER

C.O.M. YARDAGE REQUIREMENT BOTTOM LAYER

TOP TREATMENTSC.O.M YARDAGE REQUIREMENTS FOR BEVERLY VALANCE

YC27, July 2010


Single Box Pleat Double Box Pleat (w/scallop bottom)

ALLOWANCES: Width: Rod face x 3 (fullness) + returns + 2" (side hems), divided by fabric width = # cuts needed.Length: Finished length + 8" (4" double top) + 4" (2" double bottom hem) + 2" work = cut length.

Number of WIDTHS in Valance# of Widths 2 3 4 5 6 7 8 9 10Rod Face - 54" Fabric 20" - 34" 35" - 54" 55" - 76" 77" - 98" 99" - 120" 121" - 140" 141" - 162" 163" - 184" 185" - 206"

This yardage chart is figured using a 4" double top and a 2" double bottom hem. Finished Length is given up to 108" Always round up to the nearest 1/4 yard. When ordering, you MUST give TOTAL finished length, rod size, and return size.

# of Widths 2 (1) 3(2) 4(3) 5(4) 6(5) 7(6) 8(7) 9(8) 10(9)

Length - 12" 2.00 3.00 4.00 4.50 5.50 6.50 7.50 8.00 9.0018" 2.00 3.00 4.00 4.50 5.50 6.50 7.50 8.00 9.0024" 2.50 3.50 4.50 5.50 6.50 7.50 8.50 9.50 11.00



TOP TREATMENTSC.O.M YARDAGE REQUIREMENTS FOR

BOX PLEATED VALANCES


number in parenthesis, divide by 36 and add this amount to the yardage listed in the chart. Overages may

YC28, July 2010


Single Layered Box Pleat Double Layered Box Pleat Single Layered Tapered Box Pleat(also available as double layered)

ALLOWANCES: SINGLE, DOUBLE, OR TAPEREDWidth: STRAIGHT CUTS: Board face + returns = finished width. Finished width + 16" per pleat + 2" (side hems)

divided by width of fabric = # of cuts needed. (each layer)

Width: RAILROADED CUTS: Board face + returns = finished width. Finished width + 16" per pleat + 2" (side hems)

divided by 36 = total yardage needed. (each layer)

Length: Finished length (long point) + 2" tack strip + 4" hem allowance (or 1" if pillowcased bottom) + 2" work = cut length


up to 5' up to 9.5'# of Widths 2 (1) 3(2)

Up to 12" - Length 1.25 2.0012 1/4" to 18" 1.50 2.5018 1/4" to 24" 2.00 3.00



SINGLE LAYERED BOX PLEATS & TOP LAYER OF DOUBLE LAYERED VALANCE


INVERTED BOX PLEAT VALANCES

up to 9.5'3(2)1.75

2.752.25

2.00

Up to 12" - Length12 1/4" to 18"

# Feet


BOTTOM LAYER of Double Layered Valance

# Feet# of Widths

up to 5'2 (1)1.251.50

18 1/4" to 24"

YC29, July 2010


ALLOWANCES: Solid fabrics: 2x fullness Print fabrics up to 18" repeat: 2 1/2 x fullness Print fabrics up to 36" repeat: 3x fullnessVALANCE:Width: Board face width x correct fullness + 2 returns + 2" (side hems) divided by fabric width = # cuts

Length: Finished length (long point) + 28" (fullness) ( + 5" if using regular lining) = cut length of valanceCASCADING RETURNS:Length: Finished length (long point) + 4" if contrast lined (x 2 if self-lined) = cut length.

Cascading returns require 1/2 width per side up to 30" long point.

If returns are 8" or larger, and longer than 30" long point, allow 1 cut per side.

# of FEET 2 3 4 5 6 7 8 9 10FACE

Up to 12" - Face 1.50 2.50 2.50 4.00 4.00 5.00 5.00 6.50 6.5012 1/4" to 18" 1.50 3.00 3.00 4.50 4.50 6.00 6.00 7.50 7.5018 1/4" to 24" 2.00 3.50 3.50 5.00 5.00 6.50 6.50 8.00 8.00CONTRAST

Up to 12" - Contrast 1.50 2.50 2.50 4.00 4.00 5.00 5.00 6.50 6.5012 1/4" to 18" 1.50 3.00 3.00 4.50 4.50 6.00 6.00 7.50 7.5018 1/4" to 24" 2.00 3.50 3.50 5.00 5.00 6.50 6.50 8.00 8.00

# of FEET 2 3 4 5 6 7 8 9 10FACE

Up to 12" - Face 4.00 4.00 5.50 5.50 7.00 7.00 8.50 8.50 10.0012 1/4" to 18" 4.00 4.00 5.50 5.50 7.00 7.00 8.50 8.50 10.0018 1/4" to 24" 5.00 5.00 7.00 7.00 9.00 9.00 11.00 11.00 13.00CONTRAST

Up to 12" - Contrast 4.00 4.00 5.50 5.50 7.00 7.00 8.50 8.50 10.0012 1/4" to 18" 4.00 4.00 5.50 5.50 7.00 7.00 8.50 8.50 10.0018 1/4" to 24" 5.00 5.00 7.00 7.00 9.00 9.00 11.00 11.00 13.00

Up to 18" Repeat - C.O.M. YARDAGE - VALANCE

SOLID FABRICS - C.O.M. YARDAGE - VALANCE

TOP TREATMENTSC.O.M YARDAGE REQUIREMENTS FOR CAPRI, FRENCH PICKUP,

KINGS/QUEENS, KINGSTON/QUEENSTON, OPEN KINGSTON/QUEENSTON, KINGS CREATION, & RODPOCKET

KINGSTON STYLE VALANCES

YC30, July 2010


# of FEET 2 3 4 5 6 7 8 9 10FACE

Up to 12" - Face 5.00 5.00 7.00 9.00 9.00 10.00 12.00 12.00 14.0012 1/4" to 18" 5.00 5.00 7.00 9.00 9.00 10.00 12.00 12.00 14.0018 1/4" to 24" 5.00 5.00 7.00 9.00 9.00 10.00 12.00 12.00 14.00

CONTRASTUp to 12" - Contrast 5.00 5.00 5.00 7.00 7.00 10.00 12.00 12.00 14.00

12 1/4" to 18" 5.00 5.00 5.00 7.00 7.00 10.00 12.00 12.00 14.0018 1/4" to 24" 5.00 5.00 5.00 7.00 7.00 10.00 12.00 12.00 14.00

Up to 24"36"50"72"

100"

3.00 3.004.50 4.506.00 6.00

(1) (1)1.00 1.002.50 2.50

TOP TREATMENTS

C.O.M YARDAGE REQUIREMENTS FOR CAPRI, FRENCH PICKUP, KINGS/QUEENS, KINGSTON/QUEENSTON, OPEN KINGSTON/QUEENSTON,

KINGS CREATION, & RODPOCKET KINGSTON STYLE VALANCES

18 1/4" - 36" REPEAT - C.O.M. YARDAGE - VALANCE

If valance has Cascading Returns, add the following to the valance yardage.

CASCADING RETURN YARDAGECascading return

Long pointPer Pair Per PairFACE CONTRAST

YC31, July 2010


ALLOWANCES: Valance Width: Rod size x 2 + 2" divided by width of fabric = # of cuts needed for valance. Valance Length: Finished length (VALANCE long point) minus tab length + 4" (work) = cut length of valance

Tails: Long point of Valance + 1 return + 4" work x 2 divided by fabric width = # cuts needed for tails Finished length of TAIL + 4" = cut length of tails

TABS: Tab width x 3 = tab cut width, Tab length x 2 + 2" = tab cut length (allow 1/4 yard per 5 tabs needed).

The following chart has been provided to assist you in figuring the number of widths needed for proper 2 times fullnessusing 54" fabric. Allowance has been made for two 3 1/2" returns and 1 1/2" double side hems, and 2" x 4" tab size. Use the rod face width measurement to determine the number of widths needed. Always round up to the nearest whole width.

# of Widths 2 3 4 5 6 7 8 9 10Rod Face - 54" Fabric 20" - 34" 35" - 54" 55" - 76" 77" - 98" 99" - 120" 121" - 140" 141" - 162" 163" - 184" 185" - 206"

This yardage chart is figured using two 3 1/2" returns and 1 1/2" double side hems. Finished Length isgiven up to 24" tails. Always round up to the nearest 1/4 yard. When ordering, you MUST give

Finished Length, Rod Size and Return Size.

# of Widths 2 (1) 3(2) 4(3) 5(4) 6(5) 7(6) 8(7) 9(8) 10(9)

Up to 12" FL 1.50 2.00 2.25 2.50 2.75 3.25 3.50 3.75 4.25

12 1/4" to 18" 1.50 2.50 3.00 3.50 4.00 4.50 5.00 5.50 6.00

18 1/4" to 24" 3.00 3.75 4.25 5.00 5.75 6.25 7.00 7.50 8.25

Tab Yardage 0.50 0.50 1.00 1.00 1.00 1.00 1.50 1.50 1.50

The TAB YARDAGE (above) MUST be added to the standard yardage for the TOTAL yardage.54" SOLID FABRICS have been used for all yardage estimates. For repeats, multiply your repeat size times the


TOP TREATMENTS



C.O.M YARDAGE REQUIREMENTS FOR CAROLINA VALANCE

YC32, July 2010


ALLOWANCES: Width: Flat Heading; Face width + returns + 2" (work) divided by fabric width = # of cuts Top Band; Face width + returns + 2" (work) divided by fabric width = # of cuts Pleated Skirt; Face width + returns x 3 (fullness) + 2" (work) divided by fabric width = # of cutsLength: Flat Heading; Finished length + 5" (work) = cut length Top Band; Finished length size + 2" (work) = cut length Skirt; Finished Length + 4" (2" double hem) + 3" (work) = cut length

The following chart has been provided to assist you in figuring the number of widths needed for proper 3 times fullnessusing 54" fabric. Use the rod face (bracket to bracket) measurement to determine the number of widths needed.Always round up to the nearest whole width.

# of Widths 2 3 4 5 6 7 8 9 10Rod Face 20" - 34" 35" - 54" 55" - 76" 77" - 98" 99" - 120" 121" - 140" 141" - 162" 163" - 184" 185" - 206"

This yardage chart is figured using a 2" bottom hem and a 2" tacking strip, with a 5" return size.Finished length is given up to 24". Always round up to the nearest 1/4 yard. When ordering, you MUST give TOTAL finished length, rod size and return size.

# of FEET 2.5 4 5.5 7 8.5 10 11.5 13 14.5# Widths 2 (1) 3(2) 4(3) 5(4) 6(5) 7(6) 8(7) 9(8) 10(9)

Finished length up to 12" 1.00 1.50 1.50 2.00 2.50 3.00 3.00 3.50 4.0018" 1.50 2.00 2.50 3.00 3.50 4.00 4.50 5.00 5.5024" 1.50 2.50 3.00 3.50 4.50 5.00 6.00 6.50 7.00

4" flat heading 0.50 0.50 0.50 0.50 0.50 1.00 1.00 1.00 1.00

2" banding below heading 0.50 0.50 0.50 0.50 0.50 1.00 1.00 1.00 1.00


TOP TREATMENTS

C.O.M. YARDAGE REQUIREMENT (skirt)

C.O.M. YARDAGE REQUIREMENT ( 4" flat heading)

C.O.M. YARDAGE REQUIREMENT (2" contrast banding)

C.O.M YARDAGE REQUIREMENTS FOR CHARLESTON VALANCE

YC33, July 2010


ALLOWANCES: Rod face divided by 12 = # pleats (round up or down to whole number) Always one more pleat than # spaces.Rod face divided by # pleats = space size

STRAIGHT BOTTOM VALANCE:Width: Rod Face x 1 1/2 fullness + (# pleats x 10) + 2" work divided by the fabric width = # of cuts needed.

Length: Valance long point + 4" (x 2 self-lined) = cut lengthLength: Valance long point + 4" + 5" template hem = cut length

The following chart has been provided to assist you in figuring the number of widths needed for proper 2 1/2 timesfullness using 54" fabric. Use the rod face (bracket to bracket) measurement to determine the number of widths needed.Always round up to the nearest whole width.

This chart allows for Straight Bottom Valance only.# of Widths 2 3 4 5 6 7 8 9 1054" Fabric 20" - 34" 35" - 54" 55" - 76" 77" - 98" 99" - 120" 121" - 140" 141" - 162" 163" - 184" 185" - 206"

This yardage chart includes Template Hem allowances. Finished Length is given up to 24".Always round up to the nearest 1/4 yard. When ordering, you MUST give

Finished Length, Rod Size and Return Size.

This yardage chart allows fabric for Straight Bottom Valance only.# of Widths 2 (1) 3(2) 4(3) 5(4) 6(5) 7(6) 8(7) 9(8) 10(9)Face Fabric

Finished length up to

12" 1.25 1.75 2.50 3.00 3.50 4.25 4.75 5.25 6.0018" 1.75 2.50 3.25 4.00 4.75 5.50 6.25 7.00 7.7524" 2.00 3.00 4.00 5.00 6.00 7.00 8.00 9.00 10.00

Contrast FabricFinished

length up to 12" 1.25 1.75 2.50 3.00 3.50 4.25 4.75 5.25 6.0018" 1.75 2.50 3.25 4.00 4.75 5.50 6.25 7.00 7.7524" 2.00 3.00 4.00 5.00 6.00 7.00 8.00 9.00 10.00

Contrast Template

Hem 1.00 1.50 1.50 2.00 2.00 2.50 3.00 3.00 3.50


TOP TREATMENTS


C.O.M YARDAGE REQUIREMENTS FOR CHRISTINA VALANCE

YC34, July 2010


ALLOWANCES: Width: Rod face + returns = Finished Width. Finished width x 2 1/2 (fullness) + 2"(side hems), divided by fabric width = # cuts

Length: SELF-LINED & CONTRAST LINED: Finished length (l.p.) + 10" pouf allowance + double heading + double pocket + 2" work = cut length each fabricDouble yardage amount for self-lined.

Length: REGULAR LINING Finished length (l.p.) + 10" + double heading + double pocket + 7" hem allowance + 2" work = cut length

The following chart has been provided to assist you in figuring the number of widths needed for proper 2 1/2 times fullnessusing 54" fabric. Use the rod face (bracket to bracket) measurement to determine the number of widths needed.Always round up to the nearest whole width.

# of Widths 2 3 4 5 6 7 8 9 10

Rod Face - 54" Fabric 20" - 34" 35" - 54" 55" - 76" 77" - 98" 99" - 120" 121" - 140" 141" - 162" 163" - 184" 185" - 206"

This yardage chart is figured using a 2" header, 3 1/2" pockets and a 5" flip hem. Finished Length is given up to 24" Always round up to the nearest 1/4 yard. When ordering, you MUST giveTOTAL finished length, rod size and return size.

# of Widths > 2 (1) 3(2) 4(3) 5(4) 6(5) 7(6) 8(7) 9(8) 10(9)Fin. Length \/Up to 12" 2.50 3.50 4.50 5.75 6.75 8.00 9.00 10.25 11.2512 1/4" to 18" 2.75 4.00 5.25 6.50 7.75 9.00 10.25 11.50 12.7518 1/4" to 24" 3.00 4.50 6.00 7.25 8.75 10.25 11.75 13.00 14.50


TOP TREATMENTSC.O.M YARDAGE REQUIREMENTS FOR CONFEDERATE VALANCE


YC35, July 2010


COUNTRY ELEGANCE VALANCE COUNTRY ELEGANCE II VALANCE

ALLOWANCES: COUNTRY ELEGANCE & COUNTRY ELEGANCE II VALANCESSWOOPS: Up to 20" wide swoops. 1 1/2 yards for first swoop, 1 yard each additional swoop.

Over 20" wide swoops. 2 yards for first swoop, 1 1/2 yards each additional swoop.CASCADES: Finished length (long point) (x 2 if self-lined) + 4" = cut length. **1/2 width per cascade .JABOTS: Finished length (long point) (x 2 if self-lined) + 4" = cut length. **1/2 width per jabot .

3/8" Cord on Face:(Finished width x 2) + 4 returns + 10" each jabot + 10" each cascade divided by 530" bias = cord ydge. est.1/4" Cord on Cascades & Jabots: 20" each jabot + 27" each cascade divided by 570" bias = cord ydge. est.

# of FEET 3 4 5 6 7 8 9 10# of Swoops 2 2 3 3 4 4 5 6# of Jabots 1 1 2 2 3 3 4 5

1st Swoop Additional SwoopsUp to 20" Wide 1.50 1 yard per swoop

Over 20 1/4" Wide 2.00 1 1/2 yards per swoop FOR TOTAL FABRIC YARDAGEPlease add your individual yardages forJabots, Swoops and Cascades togetherto get your TOTAL FABRIC YARDAGE.

Face Fabric Contrast Fabric * Yardage for JABOTS is per JABOT.Finished length Jabots Cascades Jabots Cascades ** Yardage for CASCADES is per PAIR.Up to 12" 0.50 1.00 0.50 1.00 If you choose to Self-Line the Jabots12 1/4" to 18" 1.00 1.00 1.00 1.00 or Cascades, please DOUBLE your18 1/4" to 24" 1.00 1.00 1.00 1.00 face fabric yardage.24 1/4" to 30" 1.00 1.0031 1/4" to 72" 4.50 4.50 If you wish to have the side legs covered in face fabric, 72 1/4" to 100" 6.00 6.00 you must specify on your work order and supply

additional yardage. Add 1 yard to the allowances above.

CORDING YARDAGE# Valance feet 3 4 5 6 7 8 9 103/8" Cord/Board edge 0.50 0.50 0.50 0.50 0.50 0.75 0.75 0.753/8" Cord/across face 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50


C.O.M. YARDAGE REQUIREMENTCASCADE & JABOT YARDAGE:

54" SOLID FABRICS have been used for all yardage estimates. For repeats, multiply your repeat size times the number in parenthesis, divide by 36 and add this amount to the yardage listed in the chart.

TOP TREATMENTS

Number of FEET in Valance FINISHED WIDTH = Board Face + Two Returns

C.O.M YARDAGE REQUIREMENTS FOR COUNTRY ELEGANCE & COUNTRY ELEGANCE II VALANCES

C.O.M. YARDAGE REQUIREMENTSWOOP YARDAGE:

YC36, July 2010


DIANA VALANCE BELLE VALANCE

ALLOWANCES: DIANA & BELLE VALANCESWidth: Board face x 2 1/2 fullness + 2 returns + 2" side hems divided by fabric width = # of cuts needed.Length: Long point + 4" double top + 1" pillowcased bottom hem (or 5" template hem) + 2" work = cut length.

# of Widths 2 (0) 3 (1) 4 (2) 5 (2) 6 (3) 7 (3) 8 (4) 9 (4) 10 (5)Up to 12" 1.75 2.50 3.25 4.00 4.75 5.50 6.25 7.00 7.75

18" 2.00 3.00 4.00 5.00 6.00 7.00 8.00 9.00 10.0024" 2.25 3.50 4.50 5.50 6.50 7.75 8.75 9.75 11.00 36" 3.00 4.50 5.75 7.25 8.75 10.00 11.50 13.00 14.25

Yardage chart allows for pillowcased hem and 5" template hem.

# of Feet 2 3 4 5 6 7 8 9 101/2" Cording across face 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 1Premade Trim across face 2.00 2.50 3.50 4.00 4.50 5.00 6.00 6.50 7.00


C.O.M. YARDAGE REQUIREMENT (Diana or Belle Valance)

C.O.M. YARDAGE REQUIREMENTS FOR EXTRAS (Cord or trim across face)

C.O.M YARDAGE REQUIREMENTS FOR DIANA & BELLE VALANCES

TOP TREATMENTS

YC37, July 2010


ALLOWANCES: Width: Board face x 3 (fullness) + 2" (side hems) divided by fabric width = # cuts

Length: Finished length + 4" (2" double bottom hem) + 14" facing allowance + 2" (work) = cut length.

The following chart has been provided to assist you in figuring the number of widths needed for proper 3 times fullness.using 54" fabric.Use the rod face (bracket to bracket) measurement to determine the number of widths needed. Always round up to the nearest whole width.

Width of valance 20"-24" 24 1/4"-36" 36 1/4"-48" 48 1/4"-60" 60 1/4"-72" 72 1/4"-84" 84 1/4"-96" 108" 120"# of Widths 2 3 3 4 5 5 6 7 7


# of FEET 2 3 4 5 6 7 8 9 10# of Widths 2 (1) 3(2) 3(2) 4(3) 5(4) 5(4) 6(5) 7(6) 7(6)Up to 12" 2.00 2.75 2.75 3.75 4.50 4.50 7.25 6.25 6.2512 1/4" to 18" 2.25 3.25 3.25 4.25 5.50 5.50 6.50 7.50 7.5018 1/4" to 24" 2.50 3.75 3.75 5.00 6.25 6.25 7.50 8.75 8.75

# of FEET 2 3 4 5 6 7 8 9 10# of Widths 2 (1) 3(2) 3(2) 4(3) 5(4) 5(4) 6(5) 7(6) 7(6)1/4" cord @ Top 0.50 0.50 0.50 0.75 0.75 0.75 1.00 1.00 1.00Ties @ Top 0.50 0.50 1.00 1.00 1.00 1.50 1.50 1.50 2.0054" SOLID FABRICS have been used for all yardage estimates. For repeats, multiply your repeat size times the number in parenthesis, divide by 36 and add this amount to the yardage listed in the chart. Overages may be possible.

TOP TREATMENTS


C.O.M. YARDAGE REQUIREMENT - VALANCE

C.O.M. YARDAGE REQUIREMENT - EXTRAS @ TOP EDGE

C.O.M YARDAGE REQUIREMENTS FOR DIXIE VALANCE

YC38, July 2010


GATHERED ENGLISH CROWN VALANCE PLEATED ENGLISH CROWN VALANCE

ALLOWANCES: GATHERED & PLEATED ENGLISH CROWN VALANCEGathered:Width: Board face + 2 returns x 2 1/2 (fullness) + 2" (side hems) divided by fabric width = # cutsPleated:Width: Board face + 2 returns x 3 (fullness) + 2" (side hems) divided by fabric width = # cuts

Length Both Valances:Finished length (long point) + arch + 1" top + (1" pillowcase hem OR 5" temp hem) + 2" (work) = cut length of TAPEREDFinished length (mid-point) + arch + 1" top + (1" pillowcase hem OR 5" hem) + 2" (work) = cut length of CENTER

Face width > Up to 40"40 1/4" to

60"60 1/4" to

80"80 1/4" to

100"100 1/4" to

120"# Feet > up to 3' up to 5' up to 6.5' up to 8' up to 10'

# of Widths > 3 (2) 4 (3) 5 (4) 6 (5) 7 (6)FACE FABRICFinished Length (Long Point) \/Up to 36" long

point 3.25 4.25 5.25 6.50 7.5042" 3.75 4.75 5.75 7.00 8.50 54" solid fabrics have been used48" 4.00 5.00 6.00 7.50 9.00 for all yardage estimates. For54" 4.50 5.25 6.25 8.00 9.50 repeats multiply your repeat size60" 4.75 5.75 6.75 8.50 10.25 times the # in parenthasis, 66" 5.00 6.00 7.00 9.00 11.00 divide by 36 and add this amount72" 5.50 6.25 7.25 9.50 11.50 to the yardage listed in the chart.78" 5.75 6.75 7.75 10.00 12.25 Overages may be possible.

Please call if you would likeCONTRAST FABRIC assistance.Up to 36" long

point 3.25 4.25 5.25 6.50 7.5042" 3.75 4.75 5.75 7.00 8.5048" 4.00 5.00 6.00 7.50 9.0054" 4.50 5.25 6.25 8.00 9.5060" 4.75 5.75 6.75 8.50 10.2566" 5.00 6.00 7.00 9.00 11.0072" 5.50 6.25 7.25 9.50 11.5078" 5.75 6.75 7.75 10.00 12.25

1/2" Braiding or Trim @ top edge1/2" Braiding 1.00 1.50 1.75 2.25 2.50Premade Trim 2.25 3.25 4.00 4.75 5.75

TOP TREATMENTS

C.O.M. YARDAGE REQUIREMENTFace Width of Valance (YARDAGE includes up to 6" return)**

C.O.M YARDAGE REQUIREMENTS FOR GATHERED OR PLEATED ENGLISH CROWN VALANCES

YC39, July 2010


ALLOWANCES: Number of swoops = Rod face divided by 12 = # of swoops. Rod face divided by # of swoops = swoop size.

Width: VALANCE: Rod face x 1.75 fullness + 2" work divided by fabric width = #cuts needed for valanceLength: VALANCE: Valance finished length + 3" standard scallop @ top + 6" work = cut length.

Width: TAILS: Valance length + 1 return divided by fabric width x 2 = # cuts needed for tailsWidth: TAILS: Finished Length of tails + 4" = cut length.

The following chart has been provided to assist you in figuring the number of widths needed for proper 1.75 times fullnessusing 54" fabric. Allowance has been made for two 3 1/2" returns and pillowcased side hems.Use the rod face (bracket to bracket) measurement to determine the number of widths needed.Always round up to the nearest whole width.

Number of WIDTHS in Valance# of Widths 3 4 5 6 7 8 9 10Rod Face 35" - 54" 55" - 76" 77" - 98" 99" - 120" 121" - 140" 141" - 162" 163" - 184" 185" - 206"

Yardage allowances for Finished Length given up to 24" tails.

# of Widths 3(2) 4(3) 5(4) 6(5) 7(6) 8(7) 9(8) 10(9)FACE FABRICUp to 12" Length 2.50 3.25 4.00 4.75 5.50 6.25 7.00 7.7518" 2.50 3.50 4.50 5.50 6.25 7.25 8.25 9.2524" 3.00 4.00 5.00 6.00 7.25 8.25 9.50 10.50

CONTRASTUp to 12" Length 2.50 3.25 4.00 4.75 5.50 6.25 7.00 7.7518" 2.50 3.50 4.50 5.50 6.25 7.25 8.25 9.2524" 3.00 4.00 5.00 6.00 7.25 8.25 9.50 10.501/4" Cording 0.75 1.00 1.25 1.25 1.50 1.50 1.75 2.00Premade Trim 8.00 11.50 15.50 19.00 23.00 26.50 38.00 41.50


C.O.M YARDAGE REQUIREMENTS FOR ERIN VALANCE

TOP TREATMENTS


YC40, July 2010


ALLOWANCES: Width: Rod face x 3 (fullness) + returns + 2" (side hems), divided by width of fabric = # of cuts needed.

Length: Finished length (long point) + 4" double top + 4" work = cut length.

This yardage chart is figured using a 4" double top and a pillowcased hem. Finished Length is given up to 24". Always round up to the nearest 1/4 yard. When ordering, you MUST give TOTAL Finished Length, rod size and return size.

# of Widths 2 (1) 3(2) 3 (2) 4 (3) 5 (4) 5 (4) 6 (5) 6 (5) 7 (6)# Feet 2 3 4 5 6 7 8 9 10

Up to 12" 1.50 2.00 2.00 2.75 3.25 3.25 4.00 4.00 4.5018" 1.75 2.50 2.50 3.25 4.25 4.25 5.00 5.00 5.7524" 2.00 3.00 3.00 4.00 5.00 5.00 6.00 6.00 7.00

Template hem 0.75 1.00 1.00 1.50 0.75 1.75 2.00 2.00 2.50



TOP TREATMENTS



C.O.M YARDAGE REQUIREMENTS FOR FIVE FINGER BELL VALANCE

YC41, July 2010


ALLOWANCES: FLAT SOFT VALANCEWidth: Board face + returns + 2" (side hems) , divided by width of fabric = # of cutsWidth: Board face + returns + 32" (16"/kick pleat) + 2" (side hems) , divided by width of fabric = # of cuts

Length: STRAIGHT BOTTOM/ Finished length + 2 " (tack strip) + (5" hem allowance) or + 1" pillowcasing (self-lined or contrast lined) + 2" (work) = cut lengthLength: SCALLOPED BOTTOM/ Finished length (long point) + 5" work = cut length.# Feet --With Kick Pleat: 2 (0) 3 (1) 4 (1) 5 (1) 6 (1) 7 (2) 8 (2) 9 (2) 10 (2)Finished Length up to 12" 1.00 1.25 1.25 1.25 1.25 1.75 1.75 1.75 1.75

18" 1.00 1.75 1.75 1.75 1.75 2.50 2.50 2.50 2.5024" 1.00 2.00 2.00 2.00 2.00 3.00 3.00 3.00 3.00

# Feet -- Without Kick Pleat: 2 (0) 3 (0) 4 (0) 5 (1) 6 (1) 7 (1) 8 (1) 9 (2) 10 (2)

Finished Length up to 12" 1.00 1.00 1.00 1.25 1.25 1.25 1.25 1.75 1.7518" 1.00 1.00 1.00 1.75 1.75 1.75 1.75 2.50 2.5024" 1.00 1.00 1.00 2.00 2.00 2.00 2.00 3.00 3.00

Cording @ top 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50Premade trim 1.00 1.50 1.50 2.00 2.50 2.50 3.00 3.50 3.50

ALLOWANCES: FLAT SCULPTED VALANCEWidth: Board face + returns = Finished width. Finished width + 20" for pleats + 2" divided by fabric width = # cuts needed for valance *Allow 1 cut to line the pleatsLength: Finished length + 5" = cut length.

# Feet 2 (0) 3 (1) 4 (1) 5 (1) 6 (1) 7 (2) 8 (2) 9 (2) 10 (2)Length up to 12" 1.00 1.00 1.00 1.00 1.00 1.00 1.50 1.50 1.50

18" 1.00 1.50 1.50 1.50 1.50 1.50 2.00 2.00 2.0024" 1.00 2.00 2.00 2.00 2.00 2.00 2.50 2.50 2.50

# Feet -- with contrast pleats 2 (0) 3 (0) 4 (0) 5 (1) 6 (1) 7 (1) 8 (1) 9 (2) 10 (2)Length up to 12" 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00

18" 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.0024" 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00

Cording @ top 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50Premade trim 1.00 1.00 1.50 2.00 2.00 2.50 3.00 3.00 3.50



TOP TREATMENTS


C.O.M YARDAGE REQUIREMENTS FOR FLAT SOFT & SCULPTED VALANCES

YC42, July 2010


ALLOWANCES: VALANCE: Board face + 2 returns + 2" side hems, divided by the fabric width = number of cuts needed. Valance Long Point + 5" = cut length.

CASCADES: Allow 4 Cuts per PAIR (2 Cuts per Each Cascade) CONTRAST LINED: Finished Length (Long Point) + 4" = cut length. SELF-LINED: Finished Length (Long Point) x 2 + 4" = cut length.

(Interlining is recommended on all silks, light weight, and light colored fabrics.)

3 (0) 4 (0) 5 (1) 6 (1) 7 (1) 8 (1) 9 (2) 10 (2)

1.00 1.00 1.00 1.00 1.00 1.00 1.50 1.501.00 1.00 1.50 1.50 1.50 1.50 2.00 2.001.00 1.00 2.00 2.00 2.00 2.00 2.50 2.50

FOR TOTAL FABRIC YARDAGEPlease add your individual yardages for

TOTAL LENGTH Swoops and Cascades together to getUp to 36" your TOTAL FABRIC YARDAGE.

36 1/4" - 72" ** Yardage for CASCADES is per PAIR of CASCADES.72 1/4" - 100" If you choose to Self-Line the Cascades,

100 1/4" - 120" please DOUBLE yourFace Fabric Yardage.



Contrast Fabric (1)Cascades **

12 1/4" - 18"18 1/4" - 24"

Face Fabric (1)


C.O.M YARDAGE REQUIREMENTS FOR FREMONT VALANCE

12.00 12.0014.00 14.00

TOP TREATMENTS


Cascades **4.50 4.509.00 8.50

# FEETFinished Length

Up to 12"

YC43, July 2010


Pleat

ALLOWANCES:Width: Board Face + returns = Finished width.

Board Face + 16" each pleat + 2 returns + 2" side hems divided by fabric width = # cuts needed

Length: Finished length + 5" = cut length.

Yardage charts allow for 2 pleats as pictured.

# Feet 2 (0) 3 (1) 4 (1) 5 (1) 6 (1) 7 (2) 8 (2) 9 (2) 10 (2)Length up to 12" 1.00 1.00 1.00 1.00 1.00 1.50 1.50 1.50 1.50

18" 1.00 1.50 1.50 1.50 1.50 2.00 2.00 2.00 2.0024" 1.00 2.00 2.00 2.00 2.00 2.50 2.50 2.50 2.50

# Feet -- with contrast pleats 2 (0) 3 (0) 4 (0) 5 (1) 6 (1) 7 (1) 8 (1) 9 (2) 10 (2)

Length up to 12" 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.0018" 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.0024" 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00

Cording @ top 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50Premade trim 1.00 1.00 1.50 2.00 2.00 2.50 3.00 3.00


TOP TREATMENTSC.O.M YARDAGE REQUIREMENTS FOR GRAND PLEATED

SCALLOP VALANCE

YC44, July 2010


HARRISON VALANCE

MCCANN VALANCE MCCANN II VALANCE

ALLOWANCES: Width: Board face x 3 fullness + 2 returns + 2" work divided by fabric width = # cuts.

Length: Finished length (long point) + 5" = cut length. ALL Widths are cut at the long point.

# of Feet > 2 (1) 3 (1) 4 (2) 5 (3) 6 (3) 7 (4) 8 (5) 9 (5) 10 (6)Finished Length up to 12" 1.00 1.00 1.50 2.00 2.00 2.25 2.75 2.75 3.25

24" 1.75 1.75 2.50 3.50 3.50 4.25 5.00 5.00 6.00Cording @ top edge 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50

Trim @ top edge 1.00 1.50 1.50 2.00 2.50 2.50 3.00 3.50 3.50


Overages may be possible Please call if you would like assistance.

TOP TREATMENTS


Please call if you would like assistance with non-standard extra options.


C.O.M YARDAGE REQUIREMENTS FOR HARRISON, MCCANN, & MCANN II VALANCES

YC45, July 2010


ALLOWANCES: Width: Flat finished width + 4" (pillowcasing allowance), divided by width of fabric = # cuts needed each valance

Length: Finished length + 4" (pillowcasing allowance) = cut length.

This yardage chart is figured as pillowcased on all 4 sides. Finished Length is given up to 40".When ordering, you MUST give short point, long point, & width of each valance.

For Self-lined valances, double the Face yardage amounts.

The width of the Hilary Valance is the Board Face measurement plus two returns.Width of Valance > Up to 48" 12 1/4" to 18 1/4" to 24 1/4" to 30 1/4" to 36 1/4" to 42 1/4" to 48 1/4" to

Length of Longest Point (1) (1) (1) (1) (1) (1) (1) (1)FACE FABRIC

Up to 12" 0.50 0.50 0.50 0.50 0.50 0.50 0.50 1.0018" 0.75 0.75 0.75 0.75 0.75 0.75 0.75 1.2524" 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.7530" 1.00 1.00 1.00 1.00 1.00 1.00 1.00 2.0036" 1.25 1.25 1.25 1.25 1.25 1.25 1.25 2.2540" 1.25 1.25 1.25 1.25 1.25 1.25 1.25 2.50

CONTRAST FABRICUp to 12" 0.50 0.50 0.50 0.50 0.50 0.50 0.50 1.00

18" 0.75 0.75 0.75 0.75 0.75 0.75 0.75 1.2524" 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.7530" 1.00 1.00 1.00 1.00 1.00 1.00 1.00 2.0036" 1.25 1.25 1.25 1.25 1.25 1.25 1.25 2.2540" 1.25 1.25 1.25 1.25 1.25 1.25 1.25 2.50



TOP TREATMENTS



C.O.M YARDAGE REQUIREMENTS FOR HILARY VALANCES

YC46, July 2010


ALLOWANCES: JEANINE VALANCEWidth: Board face + returns = Finished width. Finished width + (Finished length x 2) + 2" side hems divided by fabric width = # cuts neededLength: Finished length + 5" hem allowance + 4" work = cut length.

# of FEET 2 3 4 5 6 7 8 9 10

# of Widths 2 (1) 2 (1) 2 (1) 2 (1) 3 (2) 3 (2) 3 (2) 3 (2) 3 (2)

Length Up to 18" 1.75 1.75 1.75 1.75 2.50 2.50 2.50 2.50 2.50

# of widths 2 (1) 2 (1) 2 (1) 3 (2) 3 (2) 3 (2) 3 (2) 3 (2) 4 (3)

Length 18 1/2" to 24" 2.00 2.00 2.00 3.00 3.00 3.00 3.00 3.00 3.75

# of FEET 2 3 4 5 6 7 8 9 10

1/4" Cord @ Top 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50

Premade Trim @ Top 1.00 1.00 1.50 2.00 2.00 2.50 3.00 3.00 3.50

ALLOWANCES: JEANNETTE VALANCEWidth: Board face + returns = Finished width. Board face + (long point x 2) + 2 returns + 2" side hems divided by fabric width = # cuts neededLength: Short point x 2 + Long point + 5" hem allowance + 2 1/2" = cut length.Tab: 6" cut width each tab; shortpoint x 2 + 2 = cut length each tab

# of FEET 2 3 4 5 6 7 8 9 10

# of Widths 2 (1) 2 (1) 2 (1) 2 (1) 3 (2) 3 (2) 3 (2) 3 (2) 3 (2)

Length Up to 18" 1.50 1.50 1.50 1.50 4.00 4.00 4.00 4.00 4.00

# of widths 2 (1) 2 (1) 2 (1) 3 (2) 3 (2) 3 (2) 3 (2) 3 (2) 4 (3)

Length 18 1/4" to 24" 3.00 3.00 3.00 4.50 4.50 4.50 4.50 4.50 5.75

# of FEET 2 3 4 5 6 7 8 9 10

1/4" Cord @ Top 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50

Premade Trim @ Top 1.00 1.00 1.50 2.00 2.00 2.50 3.00 3.00 3.5054" SOLID FABRICS have been used for all yardage estimates. For repeats, multiply your repeat size times the number in parenthesis, divide by 36 and add this amount to the yardage listed in the chart. Overages may be possible.




TOP TREATMENTSC.O.M YARDAGE REQUIREMENTS FOR JEANINE & JEANNETTE

VALANCES


YC47, July 2010


Inverted Corners Exterior Corners

ALLOWANCES:Width: Straight valance: Board face + returns = finished width + 6" (side hems) divided by fabric width = # cuts

Kerchief corners: 18" finished length, or less: Allow 3/4 yard per Kerchief (self or contrast)(includes self-lining)Finished length up to 18": Allow 3/4 yard per kerchief (self lined or contrast lined) (includes self-lining)Finished length 18 1/4" to 24": Allow 2yds per Kerchief (self lined or contrast contrast lined)(includes self-lining)

Length: Finished length (long point of valance) + 5" (work) = cut length.

This yardage chart is figured using a 2" bottom hem. Finished Length is given up to 24". Always round up to the nearest 1/4 yard. When ordering, youMUST give TOTAL finished length, rod size and return size.

# Feet up to 5 1/2 ft 5 1/2 to10 ft 10 to 14 ft# of Widths 2 (1) 3 (2) 4 (3)

Finished Length up to 18" 2.00 2.50 3.5018 1/4" to 24" 2.00 3.00 4.00

Cording @ top 0.50 0.50 0.50Premade trim @ top 2.00 3.50 5.00

54" SOLID FABRICS have been used for all yardage estimates. For repeats, multiply your repeat size times thenumber in parenthesis, divide by 36 and add this amount to the yardage listed in the chart. Overages may be possible. Please call if you would like assistance.

TOP TREATMENTS


C.O.M YARDAGE REQUIREMENTS FOR KERCHIEF VALANCES

YC48, July 2010


ALLOWANCES: Width: Rod face x 2 fullness + 2" (side hems), divided by width of fabric = # of cuts needed.Length: Finished length minus tab length + 7" (work/hem) = cut length. Facing cuts @ 10" (cut separately)

TABS: Tab width x 3 = cut width of tab, / Tab length x 2 + 1" = cut length of tab. (allow 1/2 yard per 3 tabs needed.)

COVERED BUTTONS: Allow 1/4 yard per 12 buttons.

The following chart has been provided to assist you in figuring the number of widths needed for proper 3 times fullnessusing 54" fabric. Allowance has been made for two 1 1/2" double side hems. Use the rod face (bracket to bracket)measurement to determine the number of widths needed. Always round up to the nearest whole width.

Number of WIDTHS in Valance# of Widths 2 3 4 5 6 7 8 9 10

Rod Face - 54" Fabric 24" - 44" 45" - 71" 72" - 98" 99" - 125" 126" - 152" 153" - 179" 180" - 206" 207" - 233" 234" - 260"

Yardage charts are figured for a Finished Length up to 24", 4" long tabs, and 10" facing.Always round up to the nearest 1/4 yard. When ordering, you MUST give Finished Length, Rod face & return size.

# of Widths 2 (1) 3(2) 4(3) 5(4) 6(5) 7(6) 8(7) 9(8) 10(9)Length up to 12" 1.50 2.00 2.75 3.50 4.00 4.75 5.50 6.00 6.75

18" 2.00 2.75 3.75 4.75 5.50 6.50 7.50 8.25 9.2524" 2.50 3.50 4.75 6.00 7.00 8.25 9.50 10.50 11.75

Button Yardage 0.50 0.50 0.50 0.50 1.00 1.00 1.00 4.00 4.00Tab Yardage 1.00 1.50 2.00 2.50 3.00 3.50 4.00 4.50 5.00

The Tab yardage & Button Yardage MUST be added to the valance yardage for overall total fabric if all the same.54" SOLID FABRICS have been used for all yardage estimates. For repeats, multiply your repeat size times the number in parenthesis, divide by 36 and add this amount to the yardage listed in the chart. Overages may be possible. Please call if you would like assistance.


TOP TREATMENTSC.O.M YARDAGE REQUIREMENTS FOR LORALYNN VALANCE

YC49, July 2010


ALLOWANCES:Width: Rod face x 3 (fullness) divided by width of fabric = number of cuts needed.

Length: Finished length (long point) x 2 1/2 (fullness) = cut length.

# of FEET 2 (1) 3 (2) 4 (2) 5 (3) 6 (4)

FACE FABRIC

Up to 12" - Face 3.00 4.25 4.25 5.50 6.75

12 1/4" to 18" 3.50 4.75 4.75 6.25 7.75

18 1/4" to 24" 3.75 5.25 5.25 7.00 8.50

CONTRAST FABRICUp to 12" - Contrast 3.00 4.25 4.25 5.50 6.7512 1/4" to 18" 3.50 4.75 4.75 6.25 7.7518 1/4" to 24" 3.75 5.25 5.25 7.00 8.50

1/4" Cording 0.50 0.50 0.50 0.75 0.75Cording Yardage MUST be added to the valance yardage.



C.O.M YARDAGE REQUIREMENTS FOR OPEN CAPRI VALANCE

TOP TREATMENTS

YC50, July 2010


ALLOWANCES:Width: Rod size + returns = Finished width. Finished width x 3 (fullness) + 2" side hems divided by fabric with = # cuts neededLength: Finished length (long point) + double heading + double pocket + 1" hem + 2" work = cut length

The following chart has been provided to assist you in figuring the number of widths needed for proper 3 times fullnessusing 54" fabric. Use the rod face (bracket to bracket) measurement to determine the number of widths needed.Always round up to the nearest whole width.

Number of WIDTHS in Valance# of Widths 2 (1) 3 (2) 4 (3) 5 (4) 6 (5) 7 (6) 8 (7) 9 (8)

Rod Face - 54" Fabric 20" - 34" 35" - 54" 55" - 76" 77" - 98" 99" - 120" 121" - 140" 141" - 162" 163" - 184"

# of Widths 2 3 4 5 6 7 8 9long point up to

12" 1.50 2.50 3.00 4.00 4.50 5.50 6.00 7.00

18" 2.00 3.00 4.00 5.00 5.50 6.50 7.50 8.50

24" 2.50 3.50 4.50 5.50 6.50 8.00 9.00 10.00


C.O.M YARDAGE REQUIREMENTS FOR PETTIPOUF VALANCE

TOP TREATMENTS

YC51, July 2010


ALLOWANCES: Width: Face width x 3 fullness divided by width of fabric = # of cuts neededLength: Finished Length (long point) + 4" single top + 5" (hem allowance) + 2" (work) = cut length

The following chart has been provided to assist you in figuring the number of widths needed for proper 2 1/2 times fullnessusing 54" fabric.Use the rod face (bracket to bracket) measurement to determine the number of widths needed.


Rod Face-54" Fabric 20" - 36" 37" - 54" 55" - 73" 74" - 91" 92" - 109" 110" - 127" 128" - 145" 146" - 163" 164" - 181"

# of Widths 2 3 4 5 6 7 8 9 10Rod Face-48" Fabric 20" - 32" 33" - 48" 49" - 65" 66" - 81" 82" - 97" 98" - 113" 114" - 129" 130" - 145" 146" - 161"Rod Face-54" Fabric 20" - 36" 37" - 54" 55" - 73" 74" - 91" 92" - 109" 110" - 127" 128" - 145" 146" - 163" 164" - 181"

This yardage chart is figured using a 4" Single Top and a 2" Double Hem. Finished Length is given up to 72".When ordering, you MUST give TOTAL finished length, rod size, and return size.


# of Widths > 2 (1) 3(2) 4(3) 5(4) 6(5) 7(6) 8(7) 9(8) 10(9)Fin. Length \/

Up to 16" 1.50 2.25 3.00 3.75 4.50 5.25 6.00 6.75 7.50

36" 3.00 4.50 6.00 7.50 9.00 10.50 12.00 13.50 15.00

42" 3.00 4.50 6.00 7.50 9.00 10.50 12.00 13.50 15.00

48" 3.50 5.25 7.00 8.75 10.50 12.25 14.00 15.75 17.50

54" 4.00 6.00 8.00 10.00 12.00 14.00 16.00 18.00 20.00

60" 4.00 6.00 8.00 10.00 12.00 14.00 16.00 18.00 20.00

66" 4.50 6.75 9.00 11.25 13.50 15.75 18.00 20.25 22.50

72" 5.00 7.50 10.00 12.50 15.00 17.50 20.00 22.50 25.00

Template Hem 1.00 1.00 1.50 2.00 2.00 2.50 2.50 3.00 3.00


TOP TREATMENTSC.O.M YARDAGE REQUIREMENTS FOR PICADILLY VALANCE

YC52, July 2010


ALLOWANCES: Width: Rod face + returns x 2 1/2 (fullness) + 2"(side hems), divided by width of fabric = # of cuts needed.Length: Finished length (long point) + 2" x 2 + double heading size + double pocket size = cut length. Standard allowance for self-lining is included in this formula.Length: Standard Lining; Finished length (long point) + 2" fullness + double heading size + double pocket size + 7" flip hem + 2" work = cut length

The following chart has been provided to assist you in figuring the number of widths needed for proper 3 times fullnessusing 54" fabric.Use the rod face (bracket to bracket) measurement to determine the number of widths needed.Always round up to the nearest whole width.


Rod Face - 54" Fabric 20" - 34" 35" - 54" 55" - 76" 77" - 98" 99" - 120" 121" - 140" 141" - 162" 163" - 184" 185" - 206"

This yardage chart is figured using a 2" header, 3 1/2" pockets. Finished Length is given up to 24".When ordering, you MUST give TOTAL finished length, rod size and return size.

C.O.M. YARDAGE REQUIREMENT# of Widths > 2 (1) 3(2) 4(3) 5(4) 6(5) 7(6) 8(7) 9(8) 10(9)

Finished Length \/Up to 12" 2.50 3.50 4.50 5.50 6.50 8.00 9.00 10.00 11.00

18" 3.00 4.50 6.00 7.50 9.00 10.00 11.50 13.00 14.5024" 3.50 5.50 7.00 9.00 10.00 12.50 14.00 16.00 17.50


Overages may be possible. Please call if you would like assistance.number in parenthesis, divide by 36 and add this amount to the yardage listed in the chart.

TOP TREATMENTSC.O.M YARDAGE REQUIREMENTS FOR POUF BOTTOM

BELL VALANCE

YC53, July 2010


ALLOWANCES: PRINCESS VALANCEWidth: Board face + 2 returns x 2 fullness divided by fabric width = # cuts neededLength: Finished length (long point) + 4" work = cut length.

# FEET 2 3 4 5 6 7 8

Length to 12" 1.00 1.00 1.00 1.00 1.50 1.50 2.00

18" 1.00 1.00 1.50 1.50 2.00 2.00 2.5024" 1.00 1.00 2.00 2.00 2.50 2.50 3.50

ALLOWANCES: HANKY VALANCEBOARD MOUNTED:Width: Board face + 2 tails + 2" divided by fabric width = # cuts neededPOLE MOUNTED:Width: Board face x 1 1/2 fullness + 2 tails + 2" divided by fabric width = # cuts needed

Length: Finished length (long point) x 1 1/2 + 2" work = cut length.

BOARD MOUNTED (up to 8" tail)

# FEET 2 (0) 3 (0) 4 (1) 5 (1) 6 (1) 7 (1) 8 (2)

Length to 12" 1.00 1.00 1.50 1.50 1.50 1.50 2.0018" 1.00 1.00 2.00 2.00 2.00 2.00 2.5024" 1.50 1.50 2.50 2.50 2.50 2.50 3.50

POLE MOUNTED (up to 8" tail)

# FEET 2 (0) 3 (1) 4 (1) 5 (1) 6 (2) 7 (2) 8 (2)

Length to 12" 1.00 1.50 1.50 1.50 2.00 2.00 2.0018" 1.00 2.00 2.00 2.00 2.50 2.50 2.5024" 1.50 2.50 2.50 2.50 3.50 3.50 3.50




C.O.M YARDAGE REQUIREMENTS FOR PRINCESS & HANKY VALANCES

TOP TREATMENTS

YC54, July 2010


ALLOWANCES: STANDARD RODSLEEVEWidth: Rod face + returns x 2 1/2 fullness + 2" (side hems), divided by width of fabric = # of cuts needed. Length: Single layer of thickness: Finished length x 2 + 3" work = cut length.Length: Double layer of thickness: Finished length x 3 + 3 1/2" work = cut length.

The following chart has been provided to assist you in figuring the number of widths needed for proper 2 1/2 times fullnessusing 54" fabric.Use the rod face (bracket to bracket) measurement to determine the number of widths needed.Always round up to the nearest whole width.


Rod Face - 54" Fabric 20" - 34" 35" - 54" 55" - 76" 77" - 98" 99" - 120" 121" - 140" 141" - 162" 163" - 184" 185" - 206"

# of Widths > 2 (1) 3(2) 4(3) 5(4) 6(5) 7(6) 8(7) 9(8) 10(9)

Finished Length \/

3 1/2" 1.00 1.25 1.75 2.00 2.50 2.25 3.25 3.50 4.00

5 1/2" 1.25 1.75 2.25 2.75 3.50 4.00 4.50 5.00 5.50

7 1/2" 1.50 2.25 3.00 3.75 4.50 5.00 5.75 6.50 7.25

9 1/2" 2.00 2.75 3.75 4.50 5.50 6.25 7.25 8.00 9.00

11" 2.25 3.25 4.25 5.25 6.25 7.25 8.25 9.25 10.2515" 2.25 4.25 5.50 6.75 8.25 9.50 10.75 12.25 13.50

ALLOWANCES: OPEN ENDED RODSLEEVEWidth: Rod size + returns = Finished width. Finished width x desired fullness + 2" side hems divided by fabric width = # cuts needed.Length: Finished length x 2 + 2" = cut length.


Rod Face - 54" Fabric 20" - 34" 35" - 54" 55" - 76" 77" - 98" 99" - 120" 121" - 140" 141" - 162" 163" - 184" 185" - 206"

# of Widths > 2 (1) 3(2) 4(3) 5(4) 6(5) 7(6) 8(7) 9(8) 10(9)

Finished Length \/

up to 12" 1.50 2.50 3.00 4.00 4.50 5.50 6.00 6.50 7.50

18" 2.50 3.50 4.50 5.50 6.50 7.50 8.50 9.50 11.00

24" 3.00 4.50 6.00 7.00 8.50 10.00 11.50 12.50 14.0054" SOLID FABRICS have been used for all yardage estimates. For repeats, multiply your repeat size times the number in parenthesis, divide by 36 and add this amount to the yardage listed in the chart. Overages may be possible.

TOP TREATMENTS



C.O.M YARDAGE REQUIREMENTS FOR RODSLEEVE & OPEN ENDED RODSLEEVE VALANCES

YC55, July 2010


ALLOWANCES: Width: Board face + 2 returns + 10% quilting shrinkage divided by fabric width = # cutsLength: Finished length of 1/2 circle + 4" work = cut length.Kerchiefs: 1 yard per pair (up to 16" long point).

1 at 1 at 1 at 2 at (1) 2 at (1) 2 at (1) 2 at (1) 2 at (1) 2 at (1)

36 x 18 42 x 21 48 x 24 27 x 13.5 30 x 15 33 x 16.50 36 x 18 39 x 19.50 42 x 21

# of FEET 3.00 3.50 4.00 4.50 5.00 5.50 6.00 6.50 7.00

Up to 13 1/2" 0.50 0.50 0.50 1.00 1.00 1.00 1.00 1.00 1.00

13 1/2" to 18" 0.75 0.75 0.75 1.50 1.50 1.50 1.50 1.50 1.50

18 1/4" to 24" 1.00 1.00 1.00 2.00 2.00 2.00 2.00 2.00 2.00

Cord @ top edge 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50

Premade trim 1.50 1.50 1.50 2.00 2.00 2.00 2.50 2.50 2.50

3 at (2) 3 at (2) 3 at (2) 3 at (2) 3 at (2) 3 at (2) 3 at (2)

30 x 15 32 x 16 34 x 17 36 x 18 38 x 19 40 x 20 42 x 21

# of FEET 7.50 8.00 8.50 9.00 9.50 10.00 10.50

Up to 13 1/2" 1.00 1.00 1.50 1.50 1.50 1.50 1.50

13 1/2" to 18" 1.50 1.50 2.25 2.25 2.25 2.25 2.2518 1/4" to 24" 2.00 2.00 3.00 3.00 3.00 3.00 3.00Cord @ top edge 0.50 0.50 0.50 0.50 0.50 0.50 0.50Premade trim 3.00 3.00 3.00 3.50 3.50 3.50 4.00

Finished Length FOR TOTAL FABRIC YARDAGEUp to 12" Please add your individual yardages for

12 1/4" to 18" together to get your18 1/4" to 24" TOTAL FABRIC YARDAGE.

54" SOLID FABRICS have been used for all yardage estimates. For repeats, multiply your repeat size times the number in parenthesis, divide by 36 and add this amount to the yardage listed in the chart. Overages may be possible. Please call if you would like assistance.No EXTRA OPTIONS Are Available on the Rushmore Valance.

2.001.502.00

Face Fabric Contrast FabricKerchief Fabric Yardage per Pair

TOP TREATMENTS

1.00 1.00


1.50

C.O.M YARDAGE REQUIREMENTS FOR RUSHMORE VALANCE

YC56, July 2010


ALLOWANCES:WIDTH:SWOOPS: Rod face divided by 12 = # swoops (round up) Always one more tab than # swoops. Rod face + (# tabs x 10) + 4" work divided by fabric width = # cuts needed

LENGTH: SELF-LINED (standardly made with a pillowcased hem) Valance long point x 2 + 4" = cut length

LENGTH: CONTRAST LINED: (standardly made with a pillowcased hem) Valance long point + 4" = cut length

TAILS: Valance length + 1 return x 2 divided by fabric width = # cuts for tails.TAILS: Finished Length of tails + 4" = cut length.

Yardage estimates are for up to 24" tails & 3 1/2" returns# of Cuts 2 (1) 3 (2) 3 (2) 4 (3) 4(3) 5 (4) 5 (4) 5 (4) 6 (5)

# of FEET 2 3 4 5 6 7 8 9 10

FACE FABRICLength up to 12" 1.50 2.25 2.25 2.75 2.75 3.50 3.50 3.50 4.00

18" 1.75 2.50 2.50 3.25 3.25 4.00 4.00 4.00 4.7524" 1.75 2.75 2.75 3.75 3.75 4.75 4.75 4.75 5.75

CONTRAST FABRICLength up to 12" 1.50 2.25 2.25 2.75 2.75 3.50 3.50 3.50 4.00

18" 1.75 2.50 2.50 3.25 3.25 4.00 4.00 4.00 4.7524" 1.75 2.75 2.75 3.75 3.75 4.75 4.75 4.75 5.75

5" contrast Template Hem 0.50 0.75 0.75 1.00 1.00 1.50 1.50 1.50 1.75

TABS 0.50 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.50

54" SOLID FABRICS have been used for all yardage estimates. For repeats, multiply your repeat size times the number in parenthesis. divide by 36 and add this amount to the yardage listed in the chart. Overages may be possible. Please call if you would like assistance.

TOP TREATMENTS

C.O.M YARDAGE REQUIREMENTS

C.O.M YARDAGE REQUIREMENTS FOR SAVANNAH VALANCE

YC57, July 2010


ExpanseStyle "a"

Expanse Expanse Style "c"Decorative Tape Top Rodpocket Top Style "b"

ALLOWANCES:PINCH PLEAT:

Width: Rod face + 2 returns x 2 1/2 fullness + 2" side hems divided by width of fabric = # of cuts needed.

Length: Finished length (long point) + 4" double top + 5" (hem allowance) + 2" (work) = cut length.

RODPOCKET:

Width: Rod face + 2 returns x 2 1/2 fullness + 2" side hems divided by width of fabric = # of cuts needed.

Length: Finished length (long point) + double heading size + double pocket size + 5" (hem allowance) +

2" (work) = cut length.

SHIRRED TOPS: (Decorative tape, Pencil Pleat tape, Shirred on tack strip, 4-cord Shirring tape)

Width: Rod face + 2 returns x 3 fullness + 2" side hems divided by width of fabric = # of cuts needed.

Length: Finished length (long point) + 4" single top + 5" (hem allowance) + 2" (work) = cut length.

Use the rod face (bracket to bracket) measurement to determine the number of widths. Always round up to the nearest width.

Number of WIDTHS in Valance


Fabric 20" to 34" 35" to 54" 55" to 76" 77" to 98" 99" to 120" 121" to 140" 141" to 162" 163" to 184" 185" to 206"

This yardage chart allows for all style of the Shaped Valance. Finished Length is given up to 36".

When ordering, you MUST give TOTAL finished length, rod size, and return size.

# of Widths > 2 (1) 3(2) 4(3) 5(4) 6(5) 7(6) 8(7) 9(8) 10(9)

Finished Length \/

Long point to 12" 2.00 2.50 3.50 4.50 5.00 6.00 7.00 7.50 8.50

18" 2.00 3.00 4.00 5.00 6.00 7.00 8.00 9.00 10.00

24" 2.50 4.00 5.00 6.00 7.50 8.50 9.50 11.00 12.00

30" 3.00 4.00 5.50 7.00 8.00 9.50 11.00 12.00 13.50

36" 3.00 4.50 6.00 7.50 9.00 10.50 12.00 13.50 15.00



TOP TREATMENTS

PINCH PLEAT, DECORATIVE TAPES, PENCIL PLEAT TAPE, SHIRRED ON TACK STRIP, & RODPOCKET STYLES

C.O.M YARDAGE REQUIREMENTS FOR SHAPED & EXPANSE VALANCES


YC58, July 2010


ALLOWANCES: SHEFFIELD & CAMILLE VALANCEWidth: PRINT FABRICS/ Board face x 3 (fullness) + returns + 2" (side hems) , divided by width of fabric = # of cuts needed.

Width: SOLID FABRICS/ Board face x 2 1/2x fullness + returns + 2" side hems, divided by fabric width = # cuts needed.* Allow 1 cut extra for cascading returns on Camille valances

Length: Sheffield: Finished length (valance long point) + 5" (work) = cut length of valance

Length: Camille: Finished length (valance long point) + 5" = cut length of valanceLength: Camille: Finished length (cascading return long point) + 5" = cut length of cascading returns

The total width of the Valance is the board face measurement plus the returns.Width of Valance Up to 24" 24 1/4"-36" 36 1/4"-48" 48 1/4"-60" 60 1/4"-72" 72 1/4"-84" 84 1/4"-96" 96 1/4"-108" 108"-120"Length of Valance (1) (2) (2) (3) (4) (4) (5) (5) (6)FACEUp to 12" 1.00 1.50 1.50 2.00 2.50 2.50 3.00 3.00 3.5012 1/4" to 18" 1.25 2.00 2.00 2.50 3.50 3.50 4.00 4.00 4.5018 1/4" to 24" 1.75 2.50 2.50 3.50 4.00 4.00 5.00 5.00 5.50

CONTRASTUp to 12" 1.00 1.50 1.50 2.00 2.50 2.50 3.00 3.00 3.5012 1/4" to 18" 1.25 2.00 2.00 2.50 3.50 3.50 4.00 4.00 4.5018 1/4" to 24" 1.75 2.50 2.50 3.50 4.00 4.00 5.00 5.00 5.50Template hem 1.00 1.00 1.00 1.50 2.00 2.00 2.00 2.00 2.50 1/4" Cording @ Top 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50Premade trim @ top 1.00 1.50 1.50 2.00 2.50 2.50 3.00 3.50 3.50

Cording Yardage must be ADDED to the Valance Yardage for TOTAL FABRIC YARDAGE.54" SOLID FABRICS have been used for all yardage estimates. For repeats, multiply your repeat size times the number in parenthesis, divide by 36 and add this amount to the yardage listed in the chart. Overages may be possible. Please call if you would like assistance.



SHEFFIELD & CAMILLE VALANCES

YC59, July 2010


ALLOWANCES: SWOOPS: Rod face divided by 12 = # swoops (round up) Always one more tab than # swoops.

Rod face + (# tabs x 10) + 4" work divided by fabric width = # cuts

LENGTH: SELF-LINED

Valance long point + 3 (for scallop) x 2 + 4" = cut length

LENGTH: CONTRAST LINED

Valance long point + 3 (for scallop) + 4" = cut length

TAILS: Valance length + 1 return x 2 tails divided by fabric width = # cuts for tails

Finshed Length of tail + 4" = cut length.

# of Cuts 3 (2) 3 (2) 4 (3) 4 (3) 5(4) 5 (4) 6 (5) 6 (5) 7 (6)

# of FEET 2 3 4 5 6 7 8 9 10

FACE FABRIC

Length up to 12" 2.00 2.00 2.50 2.50 3.00 3.00 3.50 3.50 4.50

18" 2.50 2.50 3.00 3.00 4.00 4.00 4.50 4.50 5.50

24" 3.00 3.00 3.50 3.50 4.50 4.50 5.50 5.50 6.50

CONTRAST FABRIC

Length up to 12" 2.00 2.00 2.50 2.50 3.00 3.00 3.50 3.50 4.50

18" 2.50 2.50 3.00 3.00 4.00 4.00 4.50 4.50 5.50

24" 3.00 3.00 3.50 3.50 4.50 4.50 5.50 5.50 6.50

Template Hem 0.50 1.00 1.00 1.00 1.00 1.50 1.50 1.50 2.00

TABS 0.50 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.50



C.O.M YARDAGE REQUIREMENTS

Yardage estimates are for up to 24" tails & 3 1/2" returns


C.O.M YARDAGE REQUIREMENTS FOR SHERIN VALANCE

TOP TREATMENTS

YC60, July 2010


ALLOWANCES: Width: Board face + 2 returns + 2" (for work) divided by the fabric width = # cuts needed

Length: Finished length +5" (for work) = cut length

# of FEET up to 3 4 5 6 7 8 9 10

Length Up to 16" 1.25 1.25 2.25 2.25 2.25 2.25 3.25 3.25

Template Hem 0.50 0.50 0.50 0.50 1.00 1.00 1.00 1.00

Cording @ top 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50

Premade trim @ top 1.00 1.50 2.00 2.50 2.50 3.00 3.50 3.50


TOP TREATMENTSC.O.M YARDAGE REQUIREMENTS FOR SOFT ELEGANCE

VALANCE

YC61, July 2010


ALLOWANCES:To figure the arch measurement: Bottom (base) measurement x 3.14 divided by 2 = ARCH MEASURMENTWidth: STRAIGHT CUTS: Bottom measurement x 3.14 divided by 2 = arch Arch measurement x 3 fullness divided by width of fabric = # of cuts needed.

Width: RAILROADED CUTS: Bottom measurement x 3.14 divided by 2 = arch Arch measurement x 3 fullness divided by 36 = total yardage estimate. Divide total yardage estimate in 1/2 to make with one seam when railroading. (up to 42" high)

Length: Finished height + 16" (includes rosette allowance) + double heading (if wanted-please specify) = cut length

Diameter (width)

of SUNBURST > 12" 24" 36" 48" 60" 72" 84" 96" 108"

Height of Sunburst v

Height up to 12" 1.00 1.75 3.25 4.00 4.75 5.50 6.25 7.00 8.00

18" 1.00 2.00 4.00 4.75 5.75 6.75 7.75 8.50 9.50

24" 1.25 2.25 4.50 5.75 6.75 8.00 9.00 10.00 11.25

30" 1.50 2.75 5.25 6.50 7.75 9.00 10.25 11.50 13.00

36" 1.50 3.00 6.00 7.25 8.75 10.25 11.75 13.00 14.50

42" 1.75 3.25 6.50 8.00 9.75 11.50 13.00 14.50 16.25

48" 2.00 3.75 7.25 9.00 10.75 12.50 14.25 16.00 18.00

54" 2.00 4.00 8.00 9.75 11.75 13.75 15.75 17.50 19.50

60" 2.25 4.25 8.50 10.75 12.75 15.00 17.00 19.00 21.25

Diameter (width)

of SUNBURST > 12" 24" 36" 48" 60" 72" 84" 96" 108"


Height up to 12" 1.25 2.50 3.75 4.75 6.00 7.25 8.25 8.25 9.50

18" 1.50 2.75 4.25 5.50 6.75 8.25 9.50 9.50 10.75

24" 1.75 3.25 4.75 6.25 7.75 9.25 10.75 10.75 12.25

30" 1.75 3.50 5.25 6.75 8.50 10.25 11.75 11.75 13.50

36" 2.00 3.75 5.75 7.50 9.25 11.25 13.00 13.00 14.75

42" 2.25 4.25 6.25 8.25 10.25 12.25 14.25 14.25 16.25

48" 2.25 4.50 6.75 8.75 11.00 13.25 14.25 15.25 17.50

54" 2.50 4.75 7.25 9.50 11.75 14.25 16.50 16.50 18.75

60" 2.75 5.25 7.75 10.25 12.75 15.25 17.75 17.75 20.25

Please call if you would like assistance.No EXTRA OPTIONS Are Available on the SUNBURST.

Up to 42" high will have one seam.

TOP TREATMENTSC.O.M YARDAGE REQUIREMENTS FOR STANDARD SUNBURST

C.O.M. YARDAGE REQUIREMENT - 54" FabricYardage is figured in the following chart for 3 times fullness.

C.O.M. YARDAGE REQUIREMENT - 118" Fabric

YC62, July 2010


ALLOWANCES: To figure the arch: Bottom (base) measurement x 3.14 divided by 2 = ARCH MEASUREMENTWidth: STRAIGHT CUTS:Arch measurement x 3 fullness divided by fabric width = # cuts needed. Width: RAILROADED CUTS:Arch measurement x 3 fullness divided by 36 = total yardage estimateDivide total yardage estimate in 1/2 to make with one seam when railroading (up to 30" high)Length: Finished height + 30" (includes rosette allowance) = cut length.

Diameter (width)

of SUNBURST > 12" 24" 36" 48" 60" 72" 84" 96" 108"


Height up to 12" 1.25 2.50 3.75 4.75 6.00 7.25 8.25 8.25 9.50

18" 1.50 2.75 4.25 5.50 6.75 8.25 9.50 9.50 10.75

24" 1.75 3.25 4.75 6.25 7.75 9.25 10.75 10.75 12.25

30" 1.75 3.50 5.25 6.75 8.50 10.25 11.75 11.75 13.50

36" 2.00 3.75 5.75 7.50 9.25 11.25 13.00 13.00 14.75

42" 2.25 4.25 6.25 8.25 10.25 12.25 14.25 14.25 16.25

48" 2.25 4.50 6.75 8.75 11.00 13.25 14.25 15.25 17.50

54" 2.50 4.75 7.25 9.50 11.75 14.25 16.50 16.50 18.75

60" 2.75 5.25 7.75 10.25 12.75 15.25 17.75 17.75 20.25

Diameter (width)of SUNBURST > 12" 24" 36" 48" 60" 72" 84" 96" 108"


Height up to 12" 1.00 2.00 2.50 3.50 4.00 5.00 5.50 6.50 7.50

18" 1.00 2.00 2.50 3.50 4.00 5.00 5.50 6.50 7.50

24" 1.00 2.00 2.50 3.50 4.00 5.00 5.50 6.50 7.50

30" 1.00 2.00 2.50 3.50 4.00 5.00 5.50 6.50 7.50

36" 2.00 3.50 5.00 6.50 8.00 9.50 11.00 13.00 14.50

42" 2.00 3.50 5.00 6.50 8.00 9.50 11.00 13.00 14.50

48" 2.00 3.50 5.00 6.50 8.00 9.50 11.00 13.00 14.50

54" 2.00 3.50 5.00 6.50 8.00 9.50 11.00 13.00 14.50

60" 2.00 3.50 5.00 6.50 8.00 9.50 11.00 13.00 14.50

Please call if you would like assistance. No EXTRA OPTIONS available on Sunbursts.

C.O.M. YARDAGE REQUIREMENT - 54" FabricYardage is figured in the following chart for 3 times fullness.

C.O.M. YARDAGE REQUIREMENT - 118" FabricUp to 30" high will have one seam.

TOP TREATMENTSC.O.M YARDAGE REQUIREMENTS FOR SWAGGED SUNBURST

YC63, July 2010


RODPOCKET SUNBURST

ALLOWANCES:To figure the arch: Bottom (base) measurement x 3.14 divided by 2 = Arch.

Width: 2 1/2 to 3 (fullness) x the arch.

STRAIGHT CUTS:

Bottom measurement x 3.14 divided by 2 = arch x 3 fullness divided by fabric width = # of cuts

RAILROADED CUTS:

Bottom measurement x 3.14 divided by 2 = arch x 3 fullness divided by 36 = total yardage

Length:

Height of Arch + 16" = Finished Length.

Finished length + double heading (top) + double pocket (top) = cut length.

HEIGHT > to 24" to 36" to 48" to 60" to 72"

LENGTH

Up to 12" 3.00

18" 5.00

24" 7.00

30" 9.00

36" 12.00

HEIGHT > to 24" to 36" to 48" to 60" to 72"

LENGTH

Up to 12" 2.00

18" 2.50

24" 3.50

30" 4.00

36" 9.50

TOP TREATMENTSC.O.M YARDAGE REQUIREMENTS FOR RODPOCKET SUNBURST

C.O.M. YARDAGE REQUIREMENT - 54" FabricYardage charts allow for 3x fullness

C.O.M. YARDAGE REQUIREMENT - 118" FabricUp to 30" high will have one seam.

YC64, July 2010


ALLOWANCES:Width: Rod face x 3 (fullness) + returns + 2" (side hems), divided by width of fabric = # of cutsLength: Finished length - tab length + 4" (2" dble hem) OR (1" if pillowcased bottom) + 10" facing + 2" work = cut length

TABS: Tab width x 3 = cut width of tab, / Tab length x 2 + 1" = cut length of tab. (allow 1/4 yard per 5 tabs needed).

Standard charts are figured with 2" Wide x 4" Long Tabs spaced 6" to 8" apart.

Number of WIDTHS in Drapery or Valance# of Widths 2 3 4 5 6 7 8 9 10

Rod Face - 54" Fab 15"-29" 30"-47" 48"-65" 66"-83" 84"-101" 102"-119" 120"-137" 138"-155" 156"-173"

This yardage chart is figured using 4" tabs and a 4" double bottom hem. Finished Length is given up to 108".Always round up to the nearest 1/4 yard.

When ordering, you MUST give TOTAL finished length.

C.O.M. YARDAGE REQUIREMENT# of Widths 2 (1) 3(2) 4(3) 5(4) 6(5) 7(6) 8(7) 9(8) 10(9)

Length up to 16" 1.50 2.00 2.75 3.50 4.00 4.75 5.50 6.00 6.7536" 3.00 4.50 6.00 7.25 8.75 10.25 11.75 13.00 14.5048" 3.75 5.50 7.25 9.00 10.75 12.50 14.50 16.00 18.0060" 4.25 6.50 8.50 10.75 12.75 15.00 17.00 19.00 21.2572" 5.00 7.50 10.00 12.25 14.75 17.25 19.75 22.00 24.5084" 5.75 8.50 11.25 14.00 16.75 19.50 22.25 25.00 28.0096" 6.25 9.50 12.50 15.75 18.75 22.00 25.00 28.00 31.25

108" 7.00 10.50 14.00 17.25 20.75 24.25 27.75 31.00 34.50TAB YARDAGE 0.25 0.50 0.50 0.75 0.75 1.00 1.25 1.25 1.50



TOP TREATMENTSC.O.M YARDAGE REQUIREMENTS FOR TAB VALANCES

with INVERTED BOX PLEATS & SHAPED TABS


YC65, July 2010


Pinch Pleat Top

ALLOWANCES:PINCH PLEAT:Width: Rod face + 2 returns x 2 1/2 fullness + 2" side hems divided by width of fabric = # of cuts needed. Length: Finished length (short point) + 4" double top + 5" (hem allowance) + 2" (work) = cut length (center widths)Length: Finished length (long point) + 4" double top + 5" (hem allowance) + 2" (work) = cut length (tapered widths)

RODPOCKET:Width: Rod face + 2 returns x 2 1/2 fullness + 26" side hems divided by width of fabric = # of cuts needed. Length: Finished length (short point) + double heading size + double pocket size + 5" (hem allowance) + 2" work = = cut length. (center widths)Length: Finished length (long point) + double heading size + double pocket size + 5" (hem allowance) + 2" work = = cut length. (tapered widths)

SHIRRED TOPS: (Decorative tape, Pencil Pleat tape, Shirred on tack strip, 4-cord Shirring tape)Width: Rod face + 2 returns x 3 fullness + 2" side hems divided by width of fabric = # of cuts needed.Length: Finished length (short point) + 4" single top + 5" (hem allowance) + 2" (work) = cut length (center widths)Length: Finished length (long point) + 4" single top + 5" (hem allowance) + 2" (work) = cut length (tapered widths)

*To determine # of straight widths & # tapered widths:

# WIDTHS STRAIGHT/TAPERED # WIDTHS STRAIGHT/TAPERED2 widths 1 w straight, 1 w tapered 6 widths 3 w straight, 3 w tapered3 widths 1 w straight, 2 w tapered 7 widths 3 w straight, 4 w tapered4 widths 2 w straight, 2 w tapered 8 widths 4 w straight, 4 w tapered5 widths 3 w straight, 2 w tapered 9 widths 5 w straight, 4 w tapered

10 widths 5 w straight, 5 w tapered

# of Widths 2 3 4 5 6 7 8 9 10Rod Face - 54" Fabric 20"- 34" 35"- 54" 55" - 76" 77"- 98" 99" - 120" 121" - 140" 141"- 162" 163" - 184" 185" - 206"

# of Widths > 2 (1) 3(2) 4(3) 5(4) 6(5) 7(6) 8(7) 9(8) 10(9)Finished Length \/up to 12" sp/36" lp 2.50 4.00 5.00 5.50 7.00 8.50 9.50 10.50 12.0012" sp/42" lp 2.50 4.50 5.00 6.00 7.50 9.50 10.00 11.00 12.5012" sp/48" lp 3.00 4.50 5.50 6.50 8.00 10.00 11.00 11.50 13.5012" sp/54" lp 3.00 5.00 6.00 6.50 8.50 10.50 11.50 12.50 14.50up to 18" sp/36" lp 2.50 4.00 5.00 6.00 7.50 9.00 10.00 11.00 12.5018" sp/42" lp 3.00 4.50 5.50 6.50 8.50 10.00 11.00 12.00 13.5018" sp/48" lp 3.00 5.00 6.00 7.00 8.50 10.50 11.50 12.50 14.5018"sp/54" lp 3.00 5.00 6.00 7.00 9.00 11.00 12.00 13.00 15.0054" SOLID FABRICS have been used for all yardage estimates. For repeats, multiply your repeat size times the number in parenthesis, divide by 36 and add this amount to the yardage listed in the chart. Overages may be possible. Please call if you would like assistance.

PINCH PLEAT, DECORATIVE TAPES, PENCIL PLEAT TAPE, SHIRRED ON TACK STRIP, & RODPOCKET STYLES


TAPERED VALANCES

YC66, July 2010


Board mounted Tear Drop Valances Open Tear Drop Valance w/Tabs

ALLOWANCES:Width: Board face + 2 returns = finished width. Finished width x 1 1/2 (fullness) + 2" side hems divided by fabric width = # cutsLength: Board Mounted: Finished length (long point of tear drop) x 2 = cut length Open Tear Drop: Finished length (long point) minus tab length x 2 = cut length

Standard charts are figured with 2" Wide x 4" Long Tabs# of Widths 2 3 4 5 6 7 8 9 10

Rod Face 15"-29" 30"-47" 48"-65" 66"-83" 84"-101" 102"-119" 120"-137" 138"-155" 156"-173"

This yardage chart is figured using 4" tabs and a 4" double bottom hem. Finished Length is given up to 108".Always round up to the nearest 1/4 yard.

When ordering, you MUST give TOTAL finished length.BOARD MOUNTED

C.O.M. YARDAGE REQUIREMENT# of Widths 2 (1) 3(2) 4(3) 5(4) 6(5) 7(6) 8(7) 9(8) 10(9)

Length up to 16" 1.00 2.00 2.00 3.00 3.00 4.00 4.00 4.50 4.50

up to 24" 1.50 3.00 3.00 4.00 4.00 5.50 5.50 7.00 7.00

Tab Yardage 0.25 0.50 0.50 0.75 0.75 1.00 1.25 1.25 1.50

OPEN TEAR DROPC.O.M. YARDAGE REQUIREMENT

# of Widths 2 (1) 3(2) 4(3) 5(4) 6(5) 7(6) 8(7) 9(8) 10(9)

Length up to 16" 1.00 1.50 1.50 2.00 2.00 3.00 3.00 3.50 3.50

up to 24" 1.50 2.50 2.50 3.50 3.50 4.50 4.50 6.00 6.00

Tab Yardage 0.25 0.50 0.50 0.75 0.75 1.00 1.25 1.25 1.50


Overages may be possible. Please call if you would like assistance.number in parenthesis, divide by 36 and add this amount to the yardage listed in the chart.

TOP TREATMENTSC.O.M YARDAGE REQUIREMENTS FOR TEAR DROP VALANCES

YC67, July 2010


ALLOWANCES:BOARD MOUNTED:Width: Board face + 2 returns + 2" overlap @ center + 6" divided by fabric width = # cutsLength: Finished length + 4" work = cut length

RODPOCKET:Width: Board face + 2 returns x 2 1/2 fullness divided by fabric width = # cuts (no overlap @ center)Length: Finished length + double pocket + double heading + 4" work = cut length

GROMMET TOP:Width: Board face + 2 returns x 1 1/2 fullness divided by fabric with = # cuts (no overlap @ center)Length: Finished length + 8" top + 4" = cut length (allows for both large and small grommets)

BOARD MOUNTED:

# FEET 2 (0) 3 (0) 4 (1) 5 (1) 6 (1) 7 (1) 8 (1)

Length to 36" 1.25 1.25 2.25 2.25 2.25 2.25 2.25

48" 1.50 1.50 3.00 3.00 3.00 3.00 3.00

60" 2.00 2.00 3.75 3.75 3.75 3.75 3.75

72" 2.25 2.25 4.25 4.25 4.25 4.25 4.2584" 2.50 2.50 5.00 5.00 5.00 5.00 5.00

RODPOCKET:

# WIDTHS 2 (1) 3 (2) 4 (3) 5 (4) 6 (5) 7 (6) 8 (7)

Length to 36" 3.00 4.50 6.00 7.50 9.00 10.50 12.00

48" 3.75 5.50 7.50 9.25 11.00 13.00 14.75

60" 4.50 6.50 8.75 11.00 13.00 15.25 17.50

72" 5.00 7.50 10.00 12.50 15.00 17.50 20.00

84" 5.75 8.50 11.50 14.25 17.00 20.00 22.75

* Yardage calculated using a 3 1/2" header and 3 1/2" rodpocket

GROMMET TOP:

# WIDTHS 2 (1) 3 (2) 4 (3) 5 (4) 6 (5) 7 (6) 8 (7)

Length to 36" 2.75 4.00 5.50 6.75 8.00 9.50 10.75

48" 3.50 5.00 6.75 8.50 10.00 11.75 13.50

60" 4.00 6.00 8.00 10.00 12.00 14.00 16.00

72" 4.75 7.00 9.50 11.75 14.00 16.50 18.7584" 5.50 8.00 10.75 13.50 16.00 18.75 21.50

TOP TREATMENTSC.O.M YARDAGE REQUIREMENTS FOR TENT FLAPS

YC68, July 2010


ALLOWANCES: Width: VALANCE: Board face minus 4" + 2" work divided by fabric width = # of cuts needed.

JABOTS: 22" + 1 return divided by fabric width = # cuts each jabot (normally 1 cut per jabot)

Length: VALANCE & JABOTS: Self-lined or Contrast lined: Finished length (long point) + 5 " = cut length each

Length: VALANCE & JABOTS: Regular lined w/self-template hem: Finished length (long point) + 9" = cut length each

ROSETTES: 1 1/2 YARDS WILL DO 2 ROSETTES

CORDING: Board face x 1 1/2 divided by 490" (bias) = yardage est.

This yardage chart is figured using a pillowcased bottom hem. Finished Length is given up to 24". Always round up to the nearest 1/4 yard. When ordering, you MUST give TOTAL finished length, rod size and return size.

# FEET up to 4' up to 8' up to 13' up tp 17' up to 22' # of Widths 1(1) 2 (1) 3(2) 4(3) 5(4)

FACE FABRICLength up to 12" 0.50 1.00 1.50 2.00 2.50

18" 1.00 1.50 2.00 2.50 3.5024" 1.00 2.00 2.50 3.50 4.00

CONTRAST LININGUp to 12" 0.50 1.00 1.50 2.00 2.50

18" 1.00 1.50 2.00 2.50 3.5024" 1.00 2.00 2.50 3.50 4.00

1/2" Cord across face 0.50 0.50 0.50 0.50 0.50

TOTAL LENGTHUp to 5" returns

Over 5" returns

Up to 5" returns

Over 5" returns

Up to 36" 1.50 2.50 1.50 2.50


Jabots Jabots

TOP TREATMENTSC.O.M YARDAGE REQUIREMENTS FOR VANESSA VALANCE


Face Fabric Contrast Fabric

YC69, July 2010


ALLOWANCES:Width: Board face divided by 4 (splits valance into 1/4's). 1/2 of rod size = flat center section; 1/4 of rod size = each shirred tapered section. 1/4 of board face + 1 return x 2 1/2 (fullness) + 2", divided by width of fabric = # widths each tapered section. 1/2 of board face + 2" divided by width of fabric = # of widths flat center section.Length: Finished length (short point) + single heading + 1" (pillowcased bottom) + 2" (work) = cut length. Cut length times the # of flat center widths divided by 36 = ydge.est of flat center section.Length: Finished length (long point) + single heading + 1" (pillowcased bottom) + 2" (work) = cut length. Cut length times the # of shirred, tapered widths divided by 36 = ydge.est of tapered ends.

This yardage chart is figured using a 2" Heading, two 3 1/2" Returns , Pillowcased Side Hems and 2" Pleated Ruffle at the Bottom. Finished Length is given up to 72". Always round up to the nearest 1/4 yard. When ordering, you MUST give TOTAL finished length, rod size and return size.

# of Feet > 2 (1) 3 (1) 4 (1) 5 (2) 6 (2) 7 (3) 8 (3) 9 (3) 10 (3)Short Point/Long Point \/up to 24" sp/36" lp 2.25 2.25 2.25 3.25 3.25 4.25 4.25 4.25 4.2524" sp/42" lp 2.25 2.25 2.25 3.50 3.50 4.50 4.50 4.50 4.5024" sp/48" lp 2.50 2.50 2.50 4.00 4.00 4.75 4.75 4.75 4.7524" sp/54" lp 2.75 2.75 2.75 4.25 4.25 5.25 5.25 5.25 5.2524" sp/60" lp 2.75 2.75 2.75 4.75 4.75 5.50 5.50 5.50 5.5024" sp/66" lp 3.00 3.00 3.00 5.00 5.00 5.75 5.75 5.75 5.7524" sp/72" lp 3.25 3.25 3.25 5.25 5.25 6.25 6.25 6.25 6.25

1/2" Cording (LABOR is Included)# of FEET > 2.00 3.00 4.00 5.00 6.00 7.00 8.00 9.00 10.00YARDAGE 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50Premade trim (no lip) 1.00 1.50 1.50 2.00 2.50 2.50 3.00 3.50 3.50

2" Pleated Ruffle at Bottom (LABOR is Included)# of FEET > 2.00 3.00 4.00 5.00 6.00 7.00 8.00 9.00 10.00YARDAGE 1.25 1.25 1.25 1.75 1.75 2.25 2.25 2.25 2.25


TOP TREATMENTS


EXTRAS FOR VICTORIA VALANCES

C.O.M YARDAGE REQUIREMENTS FOR VICTORIA VALANCE

YC70, July 2010


ALLOWANCES: WIDTH: 2 1/2 x fullness standard.SWOOPS: 15" to 24" wide swoops. Always one more tab than # swoops.

VALANCE w/STRAIGHT RETURNS:Length: Finished length (long point) + 10" (fullness) ( + 5" if using regular lining) = cut length of valance

CASCADING RETURNS:Cascading returns require 1 cut per side. Length: Finished length (long point) +10" if contrast lined = cut length Finished length (long point) + 10" x 2 if selflined = cut length

# of FEET 2.00 3.00 4.00 5.00 6.00 7.00 8.00 9.00 10.00# widths 2 (1) 2 (1) 3 (2) 3 (2) 4 (3) 4 (3) 5 (4) 5 (4) 6 (5)FACEUp to 12" 1.50 1.50 2.50 2.50 3.00 3.00 4.00 4.00 4..512 1/4" to 18" 2.00 2.00 3.00 3.00 4.00 4.00 5.00 5.00 5.5018 1/4" to 24" 2.50 2.50 3.50 3.50 4.50 4.50 5.50 5.50 6.50

CONTRASTUp to 12" 1.50 1.50 2.00 2.00 2.50 2.50 3.25 3.25 4.0012 1/4" to 18" 2.00 2.00 2.50 2.50 3.50 3.50 4.00 4.00 5.0018 1/4" to 24" 2.00 2.00 3.00 3.00 4.00 4.00 5.00 5.00 6.00

Tab Yardage 0.50 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.50

If valance has Cascading Returns, add the following to the valance yardage.CASCADING RETURN YARDAGE

Cascading return Long point

Per Pair FACE

Per Pair CONTRAST

(1) (1)Up to 24" 1.00 1.00

36" 2.50 2.5050" 3.00 3.0072" 4.50 4.50

100" 6.00 6.00

TOP TREATMENTS

SOLID FABRICS - C.O.M. YARDAGE - VALANCE

C.O.M YARDAGE REQUIREMENTS FOR WHIMSEY VALANCE

YC71, July 2010


ALLOWANCES:Width: Board face + 2 returns x 2 1/2 fullness + 2" side hems divided by fabric width = # cuts(if more than the standard 3 shirred sections, must use 3x fullness)

Length: Straight bottom: Finished length + 2" top + (1" pillowcased hem OR 5" hem) + 2" work = cut length.

Length: Tapered bottom: Short point of shirred section +7" work = cut length Long point of shirred section + 7" work = cut length (allow 2 cuts per valance)

# of Feet > 2 (1) 3 (1) 4 (1) 5 (2) 6 (2) 7 (3) 8 (3) 9 (3) 10 (3)Finished length \/

up to 12" 1.50 1.50 2.00 2.00 2.50 2.50 3.00 3.50 3.5016" 1.50 1.50 2.00 2.00 3.00 3.00 3.50 4.00 4.0018" 1.50 1.50 2.50 2.50 3.00 3.00 3.50 4.50 4.5024" 2.00 2.00 3.00 3.00 3.50 3.50 4.50 5.50 5.50

# of FEET > 2 3 4 5 6 7 8 9 10Short Point/Long Point \/

up to 18" sp/36" lp 2.50 2.50 3.50 3.50 4.00 4.00 4.50 5.00 5.0018" sp/42" lp 3.00 3.00 3.50 3.50 4.50 4.50 5.00 5.50 5.5018" sp/48" lp 3.50 3.50 4.00 4.00 4.50 4.50 5.50 6.00 6.0018" sp/54" lp 3.50 3.50 4.50 4.50 5.00 5.00 5.50 6.50 6.50

TOP TREATMENTS

C.O.M. YARDAGE REQUIREMENTSWILSON VALANCE - STRAIGHT BOTTOM

WILSON VALANCE - TAPERED BOTTOM

C.O.M YARDAGE REQUIREMENTS FOR WILSON VALANCE

YC72, July 2010

SWJWAGAB

GS,COT

CASCH

SCAHAR

ADERTS

E, S

ANDERSON FABRIC WORKROOM SWAGS, CASCADES & JABOTS

ALLOWANCES: TRADITIONAL, RODPOCKET, SHIRREDWidth: 1 cut per cascade (2 cuts per pair)Length: Finished length + 4" work = cut length Finished Length x 2 + 4" = cut length (self-lined)

RECOMMENDED CASCADE WIDTH:BOARD FACE: CASCADE FACE WIDTH:Up to 80" wide 10" face width80" to 100" wide 12" face width100" to 150" wide 14" face widthover 150" wide 16" face width*Minimum face width for a traditional cascade is 9".

Face Width of Cascades (YARDAGE includes 6" return)**Length of Cascade \/ 6" (1) 8" (1) 10" (1) 12" (1) 14" (1)

FACE FABRICUp to 36" 2.25 2.25 2.25 2.25 2.25

72" 4.25 4.25 4.25 4.25 4.25100" 9.00 9.00 9.00 9.00 9.00

CONTRAST FABRICUp to 36" 2.25 2.25 2.25 2.25 2.25

72" 4.25 4.25 4.25 4.25 4.25100" 9.00 9.00 9.00 9.00 9.00

ALLOWANCES: DOUBLE CASCADESWidth: 1 cut per cascadeLength: Finished length (x2 if self-lined) + 4" work = cut length

Up to 14" face width (48" fabric) = 1 width each cascadeUp to 16" face width (54" fabric) = 1 width each cascade

Double cascade face widths over the above sizes (extra charge) need 2 widths each cascade.

DOUBLE CASCADES C.O.M. YARDAGE REQUIREMENTFace Width of Cascades

FACE FABRIC 6" (1) 8" (1) 10" (1) 12" (1) 14" (1) 16" (1)Up to 36" Length 1.25 1.25 1.25 1.25 1.25 1.25

72" 2.25 2.25 2.25 2.25 2.25 2.25

CONTRAST FABRICUp to 36" Length 1.25 1.25 1.25 1.25 1.25 1.25

72" 2.25 2.25 2.25 2.25 2.25 2.25* Cascade face widths over 16"; double the yardage amounts listed.54" Solid fabrics have been used for all yardage estimates. For repeats, multiply your repeat size times the number in parenthesis, divide by 36 and add this amount to the yardage listed in the chart. Overages may be possible.

C.O.M YARDAGE REQUIREMENTS FOR TRADITIONAL, RODPOCKET, SHIRRED & DOUBLE CASCADES

TRADITIONAL, RODPOCKET, SHIIRED C.O.M. YARDAGE REQUIREMENT

CASCADES

YC73, July 10


KNOTTED CASCADES: FREMONT CASCADES:

Width: 1 cut per cascade Width: 2 cuts per cascade

Length: Finished length + 19" = cut length Length: Finished length + 14" = cut length

Finished length x 2 + 15" = cut length (self-lined) Finished length + 14" x 2 = cut length (self-lined)

SPIRAL CASCADES: STACKED CASCADES:

Width: 1 cut per cascade (over 45" length = 2 cuts) Width: 1 cut per cascade (up to 50" length)

Length: Finished length + 20" = cut length 1 1/2 cuts per cascade over 50" length)

Finished length x 2 + 20" = cut length (self-lined) Length: Finished length + 4" = cut length

Finished length x 2 + 4" = cut length (self-lined)

Yardages are calculated PER PAIR & allow for maximum Cascade face width each style.

KNOTTED FREMONT SPIRAL STACKEDLength of Cascade \ 6" Face (1) 6" Face (1) 6" Face (1) 8" Face (1)FACE FABRIC

Up to 36" 3.00 5.50 3.50 2.2545" 3.50 6.50 4.00 2.7550" 4.00 7.00 3.0072" 4.25100" 9.00

CONTRAST FABRICUp to 36" 3.00 5.50 3.50 2.2545" 3.50 6.50 4.00 2.7550" 4.00 7.00 3.0072" 4.25100" 9.00

Interlining is recommended on all silks, light weight, or light colored fabrics.

54" Solid fabrics have been used for all yardage estimates. For repeats, multiply your repeat size times the number inparenthesis, divide by 36 and add this amount to the yardage listed in the chart. Overages may be possible.

Please call if you would like assistance.

C.O.M YARDAGE REQUIREMENTS FOR KNOTTED, FREMONT, SPIRAL, & STACKED CASCADE STYLES

CASCADES


YC74, July 2010


ALLOWANCES:

Width: Face width (widest point) x 2 (x4 if double jabot) + 3" = cut width divided by width of fabric = # jabots available per width (# of cuts) needed.

Length: SELF-LINED: Finished length x 2 + 4" = cut length.Length: CONTRAST LINED: Finished length + 4" = cut length.

Finished Length of Jabots Single Jabots Double JabotsFACE FABRIC Single jabots: ydge allowance = up to 5 jabots.Up to 20" 0.75 0.75 Double jabots: ydge allowance = up to 2 jabots.28" 1.00 1.00 If you choose to Self-Line the jabots, please36" 1.25 1.25 double the face fabric yardage.

CONTRAST FABRIC 54" SOLID FABRICS have been used for all Up to 20" - CONTRAST 0.75 0.75 yardage estimates.20 1/4" to 28" 1.00 1.0028 1/4" to 36" 1.25 1.25

Double Pleated

Flat Tie Inverted Tie Inverted Tie Pleated Tie Double Tie

Double

Flat Cone Inverted Cone Inverted Cone

Country Elegance Americana Circle Jabot Madison


JABOTS

C.O.M YARDAGE REQUIREMENTS FOR JABOTS

YC75, July 2010

ANDERSON FABRIC WORKROOM SWAGS, CASCADES, & JABOTS

ANGLE TOP SWAGS:ALLOWANCE:20"- 26" wide x 14" drop 1 yard for first swag.27"- 46" wide x 21" drop 2 yards for first swag.

1 1/2 yds. each add'l. swag.46"- 55" wide x 21" drop 2 yards each swag.Over 55" wide & 21" drop Swag width + swag drop x 1 1/2 divided by 36 = yds. per swag.

ARCH TOP SWAGSALLOWANCE:20"- 26" wide x 14" drop 1 yard for first swag27"- 46" wide x 21" drop 2 yards for first swag.

1 1/2 yds. each add'l. swag.46"- 55" wide x 21" drop 2 yards each swag.Over 55" wide & 21" drop Swag width + swag drop x 1 1/2 divided by 36 = yds. per swag.

ANGLE/ARCH TOP CASCADESALLOWANCE: Width: 1 cut each cascade (2 cuts per pair)Finished Length of cascades is the highest point of arch to the long point of cascade.Finished length + 4" = cut length (if contrast lined.)Finished length x 2 + 4" = cut length (if self-lined.)

SWAGS & CASCADES

C.O.M YARDAGE REQUIREMENTS FOR ANGLE TOP OR ARCH TOP SWAGS & CASCADES

YC76, July 2010


ALLOWANCES:Width: STRAIGHT: Finished width (including returns) + 18" divided by fabric width = # cuts.Width: RAILROADED: Finished width (including returns) + 18" divided by 36" = yardage est.Length: Finished length (long point) x 2 1/2 fullness = cut length.

Number of FEET in Finished WidthFinished Width > 2' (0) 3' (0) 4' (1) 5' (1) 6' (1) 7' (1) 8' (2) 9' (2) 10' (2)Finished Length \/

Up to 12" 1.00 1.00 1.75 1.75 1.75 1.75 2.50 2.50 2.5020" 1.50 1.50 3.00 3.00 3.00 3.00 4.25 4.25 4.25

Railroaded Fabric 1.50 1.50 2.00 2.50 2.50 3.00 3.50 3.50 4.00

(Maximum 24" drop when railroading fabric.)If you wish to have the side legs covered in face fabric, you must specify on your work order and supplyadditional yardage. Add 1 yard to the allowances above which will cover up to 20" length of treatment.



SWAGS

C.O.M YARDAGE REQUIREMENTS FOR BOXED SWAG STYLES


number in parenthesis divide by 36 and add this amount to the yardage listed in the chart.

YC77, July 2010


Two Swags per Treatment; Maximum Width of 80" per Window.

ALLOWANCE: BUTTERFLY SWAGBoard face + 2 returns = Finished width.Swag drop x 2 1/2 + 2" divided by 36" = yardage per swag.

Allow one cut per cascade. Cascade Long Point + 4" = cut length per cascade.

Yardage chart allows for Maximum 80" wide window and up to 8" returns.# Feet 3 4 5 6 7 8

Finshed length (1) (1) (1) (1) (1) (1)up to 16" 2.50 2.50 2.50 2.50 2.50 2.50

20" 3.00 3.00 3.00 3.00 3.00 3.0024" 3.50 3.50 3.50 3.50 3.50 3.50

ALLOWANCE: STACKED CASCADES:Width: 1 cut per cascade (up to 50" length) 1 1/2 cuts per cascade over 50" length)

Length: Finished length + 4" = cut length Finished length x 2 + 4" = cut length (self-lined)

Yardages are calculated PER PAIR & allow for up to 8" Cascade face width and 100" long point.

CONTRAST FABRIC (1)Up to 36" 2.25 Up to 36" 2.25

45" 2.75 45" 2.7550" 3.00 50" 3.0072" 4.25 72" 4.25

100" 9.00 100" 9.00

FACE FABRIC (1)

SWAGSC.O.M YARDAGE REQUIREMENTS FOR

BUTTERFLY SWAG STYLE

YC78, July 2010


Aspen GretchenCorner Pleated

Liberty

Regency

TO CALCULATE THE WIDTH OF EACH SWAG:Board face + (# overlaps x overlap size) divided by # swags = swag width(# overlaps is one less than number of swags)(overlap size is normally the same width as cascade face width)

ALLOWANCES: Swags up to: 35" wide x 18" drop 2 yards per swag 35" to 55" wide x 20" drop 3 1/2 yards per swag

Swags Over 55" wide OR over 20" drop:Swag width + swag drop + 25" divided by fabric width = # cuts neededSwag drop x 3 = cut length x # cuts divided by 36 = yardage ext. per swag

*Swag yardages are calculated to allow for pattern matching.

SWAGSC.O.M YARDAGE REQUIREMENTS FOR CORNER PLEATED, ASPEN,

GRETCHEN, LIBERTY, & REGENCY SWAG STYLES

YC79, July 2010


EMPIRE SWAGS: J.R. KERCHIEF:ALLOWANCES: ALLOWANCES:2 yards for first swag 2 yards per swag1 1/2 yards for each add'l. swag 1/2 yard per jabot1 yard for 2 returns1 yard = 5 jabots up to 30" FL

If you wish to have the boards covered in face fabric, you must specify on your work order and supply additional yardage. Add 1 1/2 yards to the allowances above.

SWAGSC.O.M YARDAGE REQUIREMENTS FOR EMPIRE & J.R. KERCHIEF

SWAG STYLES

YC80, July 2010

ANDERSON FABRIC WORKROOOM SWAGS, CASCADES, & JABOTS

ALLOWANCE - SWAG:

Board face + returns = width each swag.

Finished width + 18" divided by fabric width = number of cuts.

Finished length (long point) x 2 1/2 (fullness) = cut length.

ALLOWANCE - SKIRT:

Board face + returns = Finished width.

Finished width x 2 1/2 (fullness) + 6" side hems divided by fabric width = # cuts

Finished length (long point) + (4" if self-lined) or + (7" if regular lining) + 2" work = cut length

(double yardage amount if skirt is self-lined)

SWAG:

nished Width 2' (0) 3' (0) 4' (1) 5' (1) 6' (1) 7' (1) 8' (2) 9' (2) 10' (2)

nished Length \/

Up to 12" 1.00 1.00 1.75 1.75 1.75 2.50 2.50 2.50 2.50

20" 1.50 1.50 3.00 3.00 3.00 4.25 4.25 4.25 4.25

SKIRT:

nished Width 2' (0) 3' (0) 4' (1) 5' (1) 6' (1) 7' (1) 8' (2) 9' (2) 10' (2)

nished Length \/

Up to 12" 1.25 1.75 1.75 2.50 2.50 3.00 3.00 3.50 3.50

20" 1.75 2.50 2.50 3.25 3.25 4.25 4.25 5.00 5.00

If you wish to have the side legs covered in face fabric, you must specify on your work order and supply

additional yardage. Add 1 yard to the allowances above.


number in parenthesis divide by 36 and add this amount to the yardage listed in the chart.


SWAGSC.O.M YARDAGE REQUIREMENTS FOR GARLAND SWAG

C.O.M. YARDAGE REQUIREMENTNumber of FEET in Finished Width

Number of FEET in Finished Width


ALLOWANCES:Board face divided by 2 = center swag width.Center swag width = 5" divided by fabric width = # cuts

Center swag width divided by 2 = width of each end swagEnd swag width + 18" + 1 return divided by fabric width = # cuts each end swag

Swag drop x 2 1/2 = cut length

SWAGS:# of FEET 3 (1) 4 (2) 5 (2) 6 (2) 7 (2) 8 (2) 9 (3) 10 (3)Finished Length

Up to 12" 2.00 2.50 2.50 2.50 2.50 2.50 3.50 3.5018" 2.50 4.00 4.00 4.00 4.00 4.00 5.00 5.0024" 3.50 5.00 5.00 5.00 5.00 5.00 7.00 7.00

Railroaded Fabric 2.50 2.50 3.00 3.50 3.50 4.00 4.50 4.50(Maximum 21" drop when railroading fabric)

MADISON JABOTS:Face Fabric (1)

TOTAL LENGTHUp to 12"

18"24"

Yardage for Madison jabots is per PAIR.If you choose to Self-Line the jabots, please DOUBLE your Face Fabric Yardage.* If you wish to have the side legs covered in face fabric, you must specify on your work order and supply additional yardage. Add 1 yard to the allowances above which will cover up to 24" length of treatment.54" SOLID FABRICS have been used for all yardage estimates. For repeats, multiply your repeat size times the number in parenthesis divide by 36 and add this amount to the yardage listed in the chart. Overages may be possible. Please call if you would like assistance.

0.50 0.501.00 1.001.00 1.00

SWAGS

C.O.M YARDAGE REQUIREMENTS FOR MADISON SWAG VALANCE

VALANCE C.O.M. YARDAGE REQUIREMENT

Contrast Fabric (1)Madison Jabots Madison Jabots

YC82, July 2010


TO CALCULATE WIDTH OF EACH SWAG:One swag per window:Rod face minus (cascade face x 2) = width ea swag

Two swag per window:Rod face minus (cascade face x 2) divided by 4 x 3 + 3 (+ 1 return) = width ea swag

Three or more swags per window: End swags:Rod face minus (cascade face x 2) divided by (total # swags x 2) x 3 + 3 (+1 return) = width ea swagCenter swags: Rod face minus (cascade face x 2) divided by (total # swags x 2) x 4 = width ea swag

ALLOWANCES:Swag width + swag drop x 1 1/2 divided by 36 = yardage estimate per swag.

SWAGSC.O.M YARDAGE REQUIREMENTS FOR OPEN RODPOCKET

SWAG STYLES

YC83, July 2010


ALLOWANCE:

1 cut per swag up to 26" wide x 14" drop

2 cuts per swag 26" - 55" wide x 21" drop (swags over 55" wide please call for estimate)

Swag all one fabric: Short point (2/3 of long point) x 2 1/2 = cut length

Swag 2 fabrics: Top swag: Short point (2/3 of long point) x 2 1/2 = cut length

Bottom swag: Long point x 2 1/2 = cut length

Knotted Cascade: (See "Cascades" for yardage charts)

6" maximum face width; 1 cut per cascade

Finished length + 15" = cut length (includes allowance for knot)

SWAGSC.O.M YARDAGE REQUIREMENTS FOR PRIMITIVE


ALLOWANCE:Board face x 2 + 6" side hems divided by the fabric width = # cutsFinished length (long point) x 1 3/4 (fullness) = cut length.Allow 1 extra yard if covering side legs with fabric.

SWAG: Number of FEET in Finished Width

Finished Width > 2' (0) 3' (0) 4' (1) 5' (1) 6' (1) 7' (1) 8' (2) 9' (2) 10' (2)

Finished Length \/

Up to 12" 1.00 1.25 1.25 1.75 1.75 2.50 2.50 3.00 3.00

20" 1.00 2.00 2.00 3.00 3.00 4.00 4.00 5.00 5.00

Tab yardage 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.25 1.25


SWAGSC.O.M YARDAGE REQUIREMENTS FOR RELAXED TAB

SWAG STYLES

YC85, July 2010


SCARF SWAGS:ALLOWANCES:Width: 1 width wide (standard).Length: Total finished length + 4" = cut length. (contrast lined).Length: Total finished length x 2 + 4" = cut length (self-lined).

EZ-STYLE SCARF SWAGS (MAGIC SWAGHOLDER)ALLOWANCES:Width: 1 width wide (standard)

Rod size (bracket to bracket). + left cascade long point + right cascade long point + 8" each dart (4 darts standard, 2 darts per swagholder) + 18" each pouf (2 poufs standard) = Finished length of scarf

Length: Finished length + 4" = cut length

EZ-STYLE SCARF SWAGS (WINDSOR POLE)ALLOWANCES:Width: 1 width (standard)

Rod size (bracket to bracket). + left cascade long point + right cascade long point + 8" each dart ( 2 darts standard, 1 dart per ring) = Finished length

Length: Finished length + 4" = cut length

SWAGSC.O.M YARDAGE REQUIREMENTS FOR SCARF SWAG OR

EZ-STYLE SCARF SWAG STYLES

YC86, July 2010


TAB SWAGS:Board Face Width 36" to 48" 49" to 70" 71" to 100" 101" to 125" 126" to 150"Recommended #

of swags per window

2 3 4 5 6

ALLOWANCES:Board face divided by # of swags = swag width.

16" wide to 20" wide swags 1 1/2 yards for first swag1 yard for each add'l swag

21" wide to 45" wide swags 2 yards for first swag1 1/2 yard for each add'l swag

The SWAG Yardage Charts are figured with the additional allowance required for pattern matching.

OPEN TAB SWAGS:ALLOWANCES:Rod face divided by # of swags = swag width.

16" wide to 20" wide swags 1 1/2 yards for first swag1 yard for each add'l swag

21" wide to 45" wide swags 2 yards for first swag1 1/2 yard for each add'l swag

The SWAG Yardage Charts are figured with the additional allowance required for pattern matching.

Jabots: 1/2 width per jabot, finished length + 4" = cut length.

SWAGSC.O.M YARDAGE REQUIREMENTS FOR TAB SWAGS & OPEN TAB

SWAG STYLES

YC87, July 2010


Shirred

Traditional Draped Open

European RodpocketRodpocket

Open

Ellie Pleated

Ellie Open

TO CALCULATE THE WIDTH OF EACH SWAG: (all styles except Wrapped)Board face width divided by (total # swags + 1) x 2 = width each swag

WRAPPED SWAGS:Board face width divided by (total # swags + 1) x 2 = width each swag in centerBoard face width divided by (total # swags + 1) x 2 + 1 return = width each swag @ ends

ALLOWANCES: All styles20" to 26" wide x 12" to 14" drop 1 yards for first swag

27" to 46" wide x 14" to 21" drop 2 yards for first swag1 1/2 yards each add'l swag

46" to 55" wide x 14" to 21" drop 2 yards for each swagOver 55" wide OR over 21" drop Swag width + swag drop x 1 1/2 divided by

36 =yds ea swag

SWAGSC.O.M YARDAGE REQUIREMENTS FOR TRADITIONAL, WRAPPED,

OPEN, SHIRRED, DRAPED OPEN, RODPOCKET, EURO, & ELLIE SWAG STYLES

YC88, July 2010


ALLOWANCES: (2 swags per window) TURBIN SWAGWidth: STRAIGHT: Board face divided by 2 + 1 return + 18" overlapping + 12" wrapping = width per swag divided by fabric width = # cuts eachWidth: RAILROADED: Board face divided by 2 + 1 return + 18" overlapping + 12" wrapping = width per swag divided by 36 = yds each swagLength: Finished length (long point) x 2 1/2 fullness = cut length.

TURBIN: Number of FEET in Finished WidthFinished Width > 4' (2) 5' (2) 6' (2) 7' (2) 8' (3) 9' (3) 10' (3)Finished Length \/Up to 12" 2.50 2.50 2.50 2.50 3.50 3.50 3.5012 1/4" to 21" 4.50 4.50 4.50 4.50 6.00 6.00 6.00Railroaded Fabric 3.00 3.50 4.00 4.00 4.50 5.00 5.00

ALLOWANCES: (2 Turbin swags & 1 Center swag per window) TURBIN II SWAGTURBIN:Width: STRAIGHT: Board face divided by 2 + 1 return + 12" wrapping = width per swag divided by fabric width = # cuts ea swagWidth: RAILROADED: Board face divided by 2 + 1 return + 12" wrapping = width per swag divided by 36 = yards ea swag Length: Finished length (long point) x 2 1/2 fullness = cut length.

CENTER SWAG:20" to 26" wide x 12" to 14" drop 1 yards for first swag27" to 46" wide x 14" to 21" drop 2 yards for first swag 1 1/2 yards each add'l swag46" to 55" wide x 14" to 21" drop 2 yards for each swagOver 55" wide OR over 21" drop Swag width + swag drop x 1 1/2 divided by 36 = yds each

TURBIN II: Number of FEET in Finished WidthFinished Width > up to 48" 54" 72" 84" 96" 108" 120"

# FEET 4' (2) 5' (2) 6' (2) 7' (2) 8' (3) 9' (3) 10' (3)Finished Length \/

Up to 12" 2.00 2.00 2.00 3.00 3.00 3.00 3.0021" 3.00 3.00 3.00 4.50 4.50 4.50 4.50

CENTER SWAGS: Swag width approximately 1/2 - 2/3 of total board faceFinished Length \/

Up to 12" 2.00 2.00 2.00 2.00 2.00 3.00 3.0021" 2.00 2.00 2.00 2.00 2.00 3.50 3.50

If you wish to have the side legs covered in face fabric, you must specify on your work order and supplyadditional yardage. Add 1 yard to the allowances above which will cover up to 21" length of treatment.54" SOLID FABRICS have been used for all yardage estimates. For repeats, multiply your repeat size times the

SWAGSC.O.M YARDAGE REQUIREMENTS FOR TURBIN

& TURBIN II SWAG STYLES




YC89, July 2010

COORNNICEE CCHAARTTS

ANDERSON FABRIC WORKROOM CORNICES

ALLOWANCES:Width: STRAIGHT CUTBoard face + 4 returns + 8" (work), divided by width of fabric = # of cuts needed.

Width: RAILROADED CUTSBoard face + 4 returns + 8" (work) = total fabric width needed, divided by 36 = ydge needed.

Length: Finished length (long point) + 1 return + 6" (work) = cut length.

All yardages are based on a RETURN of up to 6". Please add 1 additional yard if your RETURN is between 6" and 9"The Finished Width of the Cornice Equals the Boardface Measurement Plus Two Returns.

Finished Width > Up to 24" 25" to 36" 37" to 48" 49" to 60" 61" to 72" 73" to 84" 85" to 96"97" to 108"

109" to 126"

Finished Height \/ (1) (1) (1) (1) (1) (2) (2) (2) (2)Up to 10" 1.25 1.25 1.25 1.25 1.25 2.00 2.00 2.00 2.0010 1/4" to 14" 1.50 1.50 1.50 1.50 1.50 2.25 2.25 2.25 2.2514 1/4" to 18" 1.75 1.75 1.75 1.75 1.75 2.50 2.50 2.50 2.5018 1/4" to 21" 2.00 2.00 2.00 2.00 2.00 2.75 2.75 2.75 2.7521 1/4" to 24" 2.00 2.00 2.00 2.00 2.00 3.00 3.00 3.00 3.00Railroaded Fabric 2.00 2.00 2.50 3.00 3.00 3.50 4.00 4.00 4.501/4" or 3/8" Cording 0.50 0.50 0.50 0.75 0.75 1.00 1.00 1.50 1.50Premade Trim 2.00 3.00 3.50 4.50 5.00 6.00 7.00 8.00 9.00

The 1/4" or 3/8" Cording Yardage MUST be added to the Cornice Yardage for TOTAL FABRIC YARDAGE.54" SOLID FABRICS have been used for all yardage estimates. For repeats, multiply your repeat size times the number in parenthesis, divide by 36 and add this amount to the yardage listed in the chart. Overages may be possible. Please call if you would like assistance.

CORNICESC.O.M. YARDAGE REQUIREMENTS FOR STRAIGHT OR SHAPED

CORNICE STYLES AF-1, AF-2 thru AF-12, AF-35 thru AF-37

C.OM. YARDAGE REQUIREMENT

YC90, July 2010


ALLOWANCES: PLEATED CORNICEWidth: Board face + 4 returns + 8" (work) x 3 1/4 (fullness) divided by fabric width = # of cuts.Length: Finished length (long point) + 1 return + 6" (work) = cut length.

All yardages are based on a RETURN of up to 6". Please add 1 additional yard if your RETURN is between 6" and 9".The Finished Width of the Cornice Equals the Boardface Measurement Plus Two Returns.


109" to 126"

Finished Height \/ (2) (3) (4) (4) (5) (6) (6) (7) (8)Up to 10" 2.00 2.50 3.25 3.25 3.75 4.50 4.50 5.00 5.7510 1/4" to 14" 2.25 3.00 3.75 3.75 4.50 5.25 5.25 6.00 6.5014 1/4" to 18" 2.75 3.50 4.25 4.25 5.25 6.00 6.00 6.75 7.7518 1/4" to 21" 3.00 3.75 4.75 4.75 5.75 6.50 6.50 7.50 8.5021 1/4" to 24" 3.25 4.25 5.25 5.25 6.25 7.25 7.25 8.25 9.25Railroaded Fabric 3.50 4.50 5.50 6.50 7.50 8.50 10.00 11.00 12.501/4" or 3/8" Cording 0.50 0.50 0.50 0.50 0.75 0.75 1.00 1.00 1.50Premade Cord 1.50 2.50 3.00 3.50 4.50 5.00 5.50 6.50 7.50

ALLOWANCES: SHIRRED CORNICEWidth: STRAIGHT CUT Board face + 4 returns + 8" (work) x 2 1/2 (fullness), divided by width of fabric = # of cuts needed.Width: RAILROADED CUTS Board face + 4 returns + 8" (work) x 2 1/2 (fullness) = total fabric inches needed, divided by 36 = ydge needed.Length: Finished length (long point) + 1 return + 6" (work) = cut length.



109" to 126"

Finished Height \/ (1) (2) (2) (3) (3) (4) (4) (5) (6)Up to 10" 1.25 2.00 2.00 2.50 2.50 3.25 3.25 3.75 4.50

10 1/4" to 14" 1.50 2.25 2.25 3.00 3.00 3.75 3.75 4.50 5.2514 1/4" to 18" 1.75 2.50 2.50 3.50 3.50 4.25 4.25 5.00 6.0018 1/4" to 21" 2.00 2.75 2.75 3.75 3.75 4.75 4.75 5.50 6.5021 1/4" to 24" 2.00 3.00 3.00 4.00 4.00 5.00 5.00 6.00 7.00

Railroaded Fabric 3.00 3.50 4.50 5.50 6.00 7.00 8.00 10.00 11.501/4" or 3/8" Cording 0.50 0.50 0.50 0.50 0.75 0.75 1.00 1.00 1.50

Premade trim 1.50 2.50 3.00 3.50 4.50 5.00 5.50 6.50 7.50The 1/4" or 3/8" Cording Yardage MUST be added to the Cornice Yardage for TOTAL FABRIC YARDAGE.54" SOLID FABRICS have been used for all yardage estimates. For repeats, multiply your repeat size times the number in parenthesis, divide by 36 and add this amount to the yardage listed in the chart. Overages may be possible. Please call if you would like assistance.

CORNICESC.O.M. YARDAGE REQUIREMENTS FOR STRAIGHT

PLEATED OR SHIRRED CORNICE



YC91, July 2010


ALLOWANCES:CORNICE:Width: Board face + 4 returns + 8" (work) divided by fabric width = # of cuts needed. Length: Finished length (long point) + 1 return + 6" (work) = cut length.

CUTOUT ALLOWANCE Width: Board face + 4 returns + 8" (work) (x2 1/2 if shirred cutout, or x 3 1/4 if pleated cut out).Length: Cornice long point + 2" (work) = cut length.

All yardages are based on a RETURN of up to 6". Please add 1 additional yard if your RETURN is between 6" and 9". The Finished Width of the Cornice Equals the Boardface Measurement Plus Two Returns.

Finished Width > Up to 24" 25" to 36" 37" to 48" 49" to 60" 61" to 72" 73" to 84" 85" to 96" 97" to 109" to Finished Height \/ (1) (1) (1) (1) (1) (2) (2) (2) (2)

Up to 14" 1.50 1.50 1.50 1.50 1.50 2.25 2.25 2.25 2.2514 1/4" to 18" 1.75 1.75 1.75 1.75 1.75 2.75 2.75 2.75 2.7518 1/4" to 21" 2.00 2.00 2.00 2.00 2.00 3.00 3.00 3.00 3.0021 1/4" to 24" 2.25 2.25 2.25 2.25 2.25 3.25 3.25 3.25 3.25Railroaded Fabrics 2.00 2.00 2.50 3.00 3.00 3.50 4.00 4.00 4.501/4" or 3/8" Cording 0.50 0.50 0.50 0.75 0.75 1.00 1.00 1.50 1.50Premade Trim 3.00 3.00 3.50 4.50 5.00 6.00 7.00 8.00 9.00





BOTH Fabric Yardage Charts MUST be Added together to get TOTAL FABRIC YARDAGE.54" SOLID FABRICS have been used for all yardage estimates. For repeats, multiply your repeat size times the number inparenthesis, divide by 36 and add this amount to the yardage listed in the chart. Overages may be possible.

CORNICESC.O.M. YARDAGE REQUIREMENTS FOR

Pleated or Shirred Cornices (straight or shaped) with Cutouts

C.O.M. YARDAGE REQUIREMENT -- CORNICE (Frame)

C.O.M. YARDAGE REQUIREMENT -- SHIRRED CUT-OUT

C.O.M. YARDAGE REQUIREMENT -- PLEATED CUT-OUT

YC92, July 2010


2/3 face width 1/3 face width

ALLOWANCES:Cornice all one fabric:Width: STRAIGHT CUT: Board face + 4 returns + 24" (work) divided by fabric width = # of cuts

Cornice in 2 fabrics:Width: LARGE CORNICE SECTION: 2/3 of Board face + 2 returns + 12" work divided by fabric width = # of cuts SMALL CORNICE SECTION: 1/3 of Board face + 2 returns + 12" work divided by fabric width = # of cuts

Length: Finished Length (long point) + 1 Return + 6" (work) = cut length.



109" to 126"


The 1/4" or 3/8" Cording Yardage MUST be added to the Cornice Yardage for TOTAL FABRIC YARDAGE.54" SOLID FABRICS have been used for all yardage estimates. For repeats, multiply your repeat size times the number in parenthesis, divide by 36 and add this amount to the yardage listed in the chart. Overages may be possible. Please call if you would like assistance.

C.O.M.YARDAGE REQUIREMENTS FOR OVERLAPPING SHAPED CORNICE

CORNICES


YC93, July 2010


ALLOWANCES:Width: STRAIGHT CUT: Board face + 4 returns x 3 (if shirred face) + 8" (work) divided by fabric width = # of cuts. Width: RAILROADED CUTS: Board face + 4 returns x 3 (if shirred face) + 8" (work) divided by 36 = yardage est.Length: Finished length (long point) + 1 return + 5" arch height + 6" (work) = cut length.

C.O.M. YARDAGE REQUIREMENT - FLATFinished Width > Up to 24" 25" to 36" 37" to 48" 49" to 60" 61" to 72" 73" to 84" 85" to 96" 97" to 108" 109" to 126"Finished Height \/Up to 10" - FLAT 1.25 1.25 1.25 1.25 1.25 2.00 2.00 2.00 2.00

10 1/4" to 14" 1.50 1.50 1.50 1.50 1.50 2.25 2.25 2.25 2.2514 1/4" to 18" 1.75 1.75 1.75 1.75 1.75 2.50 2.50 2.50 2.5018 1/4" to 21" 2.00 2.00 2.00 2.00 2.00 2.75 2.75 2.75 2.7521 1/4" to 24" 2.25 2.25 2.25 2.25 2.25 3.25 3.25 3.25 3.25


C.O.M. YARDAGE REQUIREMENT - SHIRREDFinished Width > Up to 24" 25" to 36" 37" to 48" 49" to 60" 61" to 72" 73" to 84" 85" to 96" 97" to 108" 109" to 126"Finished Height \/

Up to 10" - SHIRRED 1.25 2.00 2.50 2.50 3.25 3.25 3.75 3.75 4.5010 1/4" to 14" 1.50 2.25 3.00 3.00 3.75 3.75 4.50 4.50 5.2514 1/4" to 18" 1.75 2.50 3.50 3.50 4.25 4.25 5.00 5.00 6.0018 1/4" to 21" 2.00 2.75 3.75 3.75 4.75 4.75 5.50 5.50 6.5021 1/4" to 24" 2.25 3.25 4.25 4.25 5.25 5.25 6.25 6.25 7.25


C.O.M. YARDAGE REQUIREMENT - EXTRAS1/4" or 3/8" Cording 0.50 0.75 0.75 1.00 1.00 1.25 1.25 1.50 1.75

1/2" Cording 0.50 0.75 0.75 1.00 1.25 1.25 1.50 1.50 1.75Premade Cords 3.25 4.25 5.25 6.25 7.25 8.25 9.25 10.25 11.75


C.O.M YARDAGE REQUIREMENTS FOR FLAT OR SHIRRED ARCHED CORNICES

CORNICES

YC94, July 2010


ALLOWANCES: FLAT SUNBURSTWidth: STRAIGHT CUT: Board face + 4 returns + 8" (work) divided by fabric width = # cuts neededWidth: RAILROADED CUTS: Face width + 4 returns + 8" (work) divided by 36 =yardage needed


Finished Width > Up to 24" 25" to 36" 37" to 48" 49" to 60" 61" to 72" 73" to 84" 85" to 96" 97" to 108"109" to

126"Finished Height \/ (1) (1) (1) (1) (1) (2) (2) (2) (2)

Up to 10" 1.25 1.25 1.25 1.25 1.25 2.00 2.00 2.00 2.0010 1/4" to 14" 1.50 1.50 1.50 1.50 1.50 2.25 2.25 2.25 2.2514 1/4" to 18" 1.75 1.75 1.75 1.75 1.75 2.50 2.50 2.50 2.5018 1/4" to 21" 2.00 2.00 2.00 2.00 2.00 2.75 2.75 2.75 2.7521 1/4" to 24" 2.00 2.00 2.00 2.00 2.00 3.00 3.00 3.00 3.00Railroaded Fabric 2.00 2.00 2.50 3.00 3.00 3.50 4.00 4.00 4.501/4" or 3/8" Cording 0.50 0.50 0.50 0.75 0.75 1.00 1.00 1.50 1.50Premade Trim 2.00 3.00 3.50 4.50 5.00 6.00 7.00 8.00 9.00

ALLOWANCES: SHIRRED SUNBURSTWidth: STRAIGHT CUT: Board face + long point + long point x 3 fullness (shirring) + 4 returns + 8" (work) divided by width of fabric = # of cuts needed.Width: RAILROADED CUTS: Board face + long point + long point x 3 fullness (shirring) + 4 returns + 8" (work) divided by 36 = ydge needed. Length: Finished length (long point) + 1 return + 10" (work) = cut length\

Finished Width > Up to 24" 25" to 36" 37" to 48" 49" to 60" 61" to 72" 73" to 84" 85" to 96" 97" to 108" 109" to 126"Finished Height \/

Up to 10" 2.25 (2) 3.00 (3) 3.75 (4) 3.75 (4) 4.50 (5) 5.25 (6) 5.25 (6) 6.00 (7) 6.50 (8)10 1/4" to 14" 3.50 (3) 4.25 (4) 4.25 (4) 5.00 (5) 6.00 (6) 6.00 (6) 6.75 (7) 6.75 (7) 8.50 (9)14 1/4" to 18" 4.00 (3) 4.75 (4) 5.75 (5) 5.75 (5) 6.75 (6) 7.75 (7) 7.75 (7) 8.50 (8) 9.50 (9)18 1/4" to 21" 5.25 (4) 5.25 (4) 6.25 (5) 7.25 (6) 7.25 (6) 8.25 (7) 9.25 (7) 9.25 (8) 10.50 (9)21 1/4" to 24" 5.75 (4) 6.75 (5) 6.75 (5) 8.00 (6) 9.00 (7) 9.00 (7) 10.00 (7) 10.00 (8) 12.25 (10)

1/4" or 3/8" Cording 0.50 0.50 0.50 0.75 0.75 1.00 1.00 1.50 1.50Premade Trim 2.00 3.00 3.50 4.50 5.00 6.00 7.00 8.00 9.00

54" SOLID FABRICS have been used for all yardage estimates. For repeats, multiply your repeat size times the number in parenthesis, divide by 36 and add this amount to the yardage listed in the chart. Overages may be possible. Please call if you would like assistance.All yardages are based on a RETURN of up to 6". Please add 1 additional yard if your return is between 6" and 9".

C.O.M. YARDAGE REQUIREMENTS FOR FLAT OR SHIRRED SUNBURST CORNICES

CORNICES



YC95, July 2010


ALLOWANCES:Width: TOP LAYER Board face + 4 returns + 8" (work) divided by fabric width = # cutsLength: TOP LAYER Finished length (long point) + 1 return + 6" (work) = cut lengthWidth: UNDER LAYER Board face + 8" (work) divided by fabric width = # cutsLength: UNDER LAYER Finished Length + 8" (work) = cut length

All yardages are based on a RETURN of up to 6". Please add 1 additional yard if your return is between 6" and 9".

The Finished Width of the Cornice Equals the Boardface Measurement Plus Two Returns.

Finished Width > Up to 24"24 1/4"-

36"36 1/4"-

48"48 1/4"-

60"60 1/4"-

72"72 1/4"-

84"84 1/4"-

96"96 1/4"-

108" 108"-126"Finished Height \/ (1) (1) (1) (1) (1) (2) (2) (2) (2)

TOP LAYERUp to 10" 1.50 1.50 1.50 1.50 1.50 2.00 2.00 2.00 2.00

14" 1.50 1.50 1.50 1.50 1.50 2.25 2.25 2.25 2.2518" 1.75 1.75 1.75 1.75 1.75 2.50 2.50 2.50 2.5021" 2.00 2.00 2.00 2.00 2.00 2.75 2.75 2.75 2.7524" 2.00 2.00 2.00 2.00 2.00 3.00 3.00 3.00 3.00

Railroad Fabric 2.00 2.00 2.50 3.00 3.00 3.50 4.00 4.00 4.50

UNDER LAYER (0) (0) (1) (1) (1) (1) (1) (2) (2)Up to 6" 0.50 0.50 1.00 1.00 1.00 1.00 1.25 1.25 1.25

10" 0.50 0.50 1.00 1.00 1.00 1.00 1.50 1.50 1.50 14" 0.75 0.75 1.25 1.25 1.25 1.25 2.00 2.00 2.00 17" 0.75 0.75 1.50 1.50 1.50 1.50 2.25 2.25 2.25 20" 1.00 1.00 1.75 1.75 1.75 1.75 2.50 2.50 2.50

Railroad Fabric 1.00 1.50 2.00 2.00 2.50 3.00 3.00 3.50 4.001/4" or 3/8" Cording 0.50 0.50 1.00 1.00 1.00 1.00 1.50 1.50 1.50



CORNICESC.O.M.YARDAGE REQUIREMENTS FOR FLAT TAPERED CORNICE

with STRAIGHT UNDER LAYER

YC96, July 2010


ALLOWANCES: TAPERED CORNICE W/DIAGONAL PLEATINGWidth: STRAIGHT CUT: Board face + 2 returns + 12" (work) divided by fabric width = # cuts each side x 2 Width: RAILROADED CUTS: Board face + 2 returns + 12" (work) divided by 36" = ydge est. x 2Length: Finished Length (long point) x 3 times fullness = cut length.

All yardages are based on a RETURN of up to 6". Please add 1 additional yard if your return is between 6" and 9".The Finished Width of the Cornice Equals the Boardface Measurement Plus Two Returns.


109" to 126"

Finished Height \/ (1) (2) (2) (3) (3) (3) (4) (4) (5)

Up to 10" 2.00 2.50 2.50 3.50 3.50 3.50 4.50 4.50 5.00

10 1/4" to 14" 2.50 3.50 3.50 5.00 5.00 5.00 6.00 6.00 7.00

14 1/4" to 18" 3.00 4.50 4.50 6.00 6.00 6.00 7.50 7.50 9.00

18 1/4" to 21" 3.50 5.50 5.50 7.00 7.00 7.00 9.00 9.00 10.50

21 1/4" to 24" 4.00 6.00 6.00 8.00 8.00 8.00 10.00 10.00 12.00


ALLOWANCE: HORIZONTAL PLEATED

Board face + 4 returns + 8" work divided by fabric width = # cuts needed

Finished length (long point) x 4 fullness + 1 return (to cover top) + 6" work = cut length

Includes 1" Plastic Slats in each fold to hold shape.

All yardages are based on a RETURN of up to 6". Please add 1 additional yard if your RETURN is between 6" and 9".


Finished Width > 25" to 36" 37" to 48" 49" to 60" 61" to 72" 73" to 84" 85" to 96"97" to 108"

109" to 126"

Finished Height \/ (1) (1) (1) (1) (2) (2) (2) (5)

Up to 10" 3.00 3.00 3.00 3.00 4.50 4.50 4.50

10 1/4" to 14" 4.00 4.00 4.00 4.00 5.75 5.75 5.75

14 1/4" to 18" 4.75 4.75 4.75 4.75 7.25 7.25 7.25

18 1/4" to 21" 5.25 5.25 5.25 5.25 7.75 7.75 7.75

21 1/4" to 24" 6.25 6.25 6.25 6.25 9.25 9.25 9.25


number in parenthesis, divide by 36 and add this amount to the yardage listed in the chart. Overages may be possible.


CORNICES


C.O.M. YARDAGE REQUIREMENTS FOR TAPERED CORNICE w/DIAGONAL PLEATING & HORIZONTAL PLEATED CORNICE

YC97, July 2010


ALLOWANCES:CORNICE:Width: STRAIGHT CUT: Board face + 4 returns + 8" (work) divided by fabric width = # cuts neededWidth: RAILROADED CUTS: Board face + 4 returns + 8" (work) divided by 36 = yardage neededLength: Finished length (long point) + 1 return + 6" (work) = cut length.

GATHERED SKIRT:Width: Board face + 2 returns x 2 1/2 (fullness) divided by width of fabric = number of cuts needed.Length: Finished length + 6" (work) = cut length neededADD Cornice and skirt yardage together for TOTAL yardage needed.


The Finished Width of the Cornice Equals the Boardface Measurement Plus Two Returns.Finished Width > Up to 24" 25" - 36" 37" - 48" 49" - 60" 61" - 72" 73" - 84" 85" - 96" 97" - 108" 109"- 126"Finished Height \/ (1) (1) (1) (1) (1) (2) (2) (2) (2)

Up to 10" 1.25 1.25 1.25 1.25 1.25 2.00 2.00 2.00 2.0010 1/4" to 14" 1.50 1.50 1.50 1.50 1.50 2.25 2.25 2.25 2.2514 1/4" to 18" 1.75 1.75 1.75 1.75 1.75 2.50 2.50 2.50 2.5018 1/4" to 21" 2.00 2.00 2.00 2.00 2.00 2.75 2.75 2.75 2.7521 1/4" to 24" 2.00 2.00 2.00 2.00 2.00 3.00 3.00 3.00 3.00

Railroaded Fabric 2.00 2.00 2.50 3.00 3.00 3.50 4.00 4.00 4.501/4" or 3/8" Cord 0.50 0.50 0.50 0.50 0.50 1.00 1.00 1.00 1.00

Premade Trim 1.50 2.50 3.00 3.50 4.50 5.00 5.50 6.50 7.50

# of Widths > 2 (1) 2 (1) 3 (2) 3 (2) 4 (3) 4 (3) 5 (4) 5 (4) 6 (5)Finished Length \/ Up to 24" 25" - 36" 37" - 48" 49" - 60" 61" - 72" 73" - 84" 85" - 96" 97" - 108" 109"- 126"

Up to 12" 1.00 1.00 1.50 1.50 2.00 2.00 2.50 2.50 3.0012 1/4" to 16" 1.25 1.25 2.00 2.00 2.50 2.50 3.25 3.25 3.7516 1/4" to 20" 1.50 1.50 2.25 2.25 3.00 3.00 3.75 3.75 4.50


CORNICESC.O.M. YARDAGE REQUIREMENTSE FOR STRAIGHT CORNICE

w/SHAPED GATHERED SKIRT

C.O.M. YARDAGE REQUIREMENT - CORNICE

C.O.M. YARDAGE REQUIREMENT - SKIRT

YC98, July 2010


ALLOWANCES:CORNICE:Width: STRAIGHT CUT: Board face + 4 returns + 8" (work) divided by width of fabric=# of cuts needed.Width: RAILROADED CUTS: Board face + 4 returns + 8" (work) = divided by 36 = yardage needed.Length: Finished length (long point) + 1 return + 6" (work) = cut length.

GATHERED SKIRT:Width: Board face + 2 returns x 2 1/2 fullness divided by width of fabric = number of cuts needed. Length: Finished length (long point) + 6" (work) = cut length needed.ADD Cornice and skirt yardage together for TOTAL yardage needed.

All yardages are based on a RETURN of up to 6". Please add 1 additional yard if your return is between 6" and 9"

The Finished Width of the Cornice Equals the Boardface Measurement Plus Two Returns.Finished Width > Up to 24" 25" - 36" 37" - 48" 49" - 60" 61" - 72" 73" - 84" 85" - 96" 97" - 108" 109"- 126"Finished Height \/ (1) (1) (1) (1) (1) (2) (2) (2) (2)

Up to 10" 1.25 1.25 1.25 1.25 1.25 2.00 2.00 2.00 2.0010 1/4" to 14" 1.50 1.50 1.50 1.50 1.50 2.25 2.25 2.25 2.2514 1/4" to 18" 1.75 1.75 1.75 1.75 1.75 2.50 2.50 2.50 2.5018 1/4" to 21" 2.00 2.00 2.00 2.00 2.00 2.75 2.75 2.75 2.7521 1/4" to 24" 2.00 2.00 2.00 2.00 2.00 3.00 3.00 3.00 3.00

Railroaded Fabric 2.00 2.00 2.50 3.00 3.00 3.50 4.00 4.00 4.501/4" or 3/8" Cord 0.50 0.50 0.50 0.75 0.75 1.00 1.00 1.50 1.501/2" Shirred Cord 0.75 1.00 1.50 1.50 2.00 2.50 2.50 3.00 3.50

# of Widths > 2 (1) 2 (1) 3 (2) 3 (2) 4 (3) 4 (3) 5 (4) 5 (4) 6 (5)Finished Length \/ Up to 24" 25" - 36" 37" - 48" 49" - 60" 61" - 72" 73" - 84" 85" - 96" 97" - 108" 109"- 126"

Up to 12" 1.00 1.00 1.50 1.50 2.00 2.00 2.50 2.50 3.0012 1/4" to 16" 1.25 1.25 2.00 2.00 2.50 2.50 3.25 3.25 3.7516 1/4" to 20" 1.50 1.50 2.25 2.25 3.00 3.00 3.75 3.75 4.50


C.O.M. YARDAGE REQUIREMENT - CORNICE

C.O.M. YARDAGE REQUIREMENT - SKIRT

CORNICESC.O.M. YARDAGE REQUIREMENTS FOR SHAPED CORNICE

w/GATHERED SKIRT

YC99, July 2010

ANDERSON FABRIC WORKROOOM CORNICES

ALLOWANCES:Width: STRAIGHT CUT: Board face + 4 returns + 8" (work) divided by fabric width = # of cuts needed.Width: RAILROADED CUTS: Board face + 4 returns + 8" (work) divided by 36 = yardage needed.Length: Finished length (long point) + 1 return + 6" (work) = cut length.Crown: 6" cut length (separate from cornice)


Finished Width > Up to 24" 25" to 36" 37" to 48" 49" to 60" 61" to 72" 73" to 84" 85" to 96" 97" to 108" 109" to 126"Finished Height \/ (1) (1) (1) (1) (1) (2) (2) (2) (2)Up to 10" 2.00 2.00 2.00 2.00 2.00 2.50 2.50 2.50 2.5010 1/4" to 14" 2.00 2.00 2.00 2.00 2.00 3.00 3.00 3.00 3.0014 1/4" to 18" 2.00 2.00 2.00 2.00 2.00 3.00 3.00 3.00 3.0018 1/4" to 21" 2.50 2.50 2.50 2.50 2.50 3.50 3.50 3.50 3.5021 1/4" to 24" 2.50 2.50 2.50 2.50 2.50 4.00 4.00 4.00 4.00Railroaded Fabric 2.00 2.00 2.50 3.00 3.00 3.50 4.00 4.00 4.503/8" Cording 1.00 1.00 1.00 1.00 1.00 1.00 1.00 2.00 2.00

54" SOLID FABRICS have been used for all yardage estimates. For repeats, multiply your repeat size times the number in parenthesis divide by 36 and add this amount to the yardage listed in the chart. Overages may be possible. Please call if you would like assistance.


C.O.M. YARDAGE REQUIREMENTS FOR SHAPED PADDED CORNICE w/CURLY CUE CORDING & CROWN HEADING

CORNICES

YC100, July 2010


CORNICES

Homeward Bound (AF23)

Little Choo Choo (AF24)

*For custom banding designs - please provide template.

ALLOWANCES:Width: STRAIGHT CUT Board face + 4 returns + 8" (work), divided by width of fabric = # of cuts needed.Width: RAILROADED CUTS Board face + 4 returns + 8" (work) = total fabric inches needed, divided by 36 = ydge needed.




109" to 126"

Finished Height \/ (1) (1) (1) (1) (1) (2) (2) (2) (2)Up to 10" 1.25 1.25 1.25 1.25 1.25 2.00 2.00 2.00 2.00

10 1/4" to 14" 1.50 1.50 1.50 1.50 1.50 2.25 2.25 2.25 2.2514 1/4" to 18" 1.75 1.75 1.75 1.75 1.75 2.50 2.50 2.50 2.5018 1/4" to 21" 2.00 2.00 2.00 2.00 2.00 3.00 3.00 3.00 3.0021 1/4" to 24" 2.25 2.25 2.25 2.25 2.25 3.25 3.25 3.25 3.25

Railroaded Fabric 2.00 2.00 2.50 3.00 3.00 4.00 4.00 4.00 4.501/4" or 3/8" Cording 0.50 0.50 0.50 0.75 0.75 1.00 1.00 1.00 1.00

1/2" Cording 0.50 0.50 0.50 0.75 0.75 1.00 1.00 1.00 1.25Premade Trim 2.75 2.75 3.50 4.25 4.75 6.25 6.25 7.00 8.00

Shaped Banding * 2.00 2.00 2.75 2.75 2.75 3.50 3.50 3.50 3.50Custom banding: please submit for estimate (template must be provided)

included for the Outline 1/4" or 3/8" Cording.* The Size of Banding will be in proportion to the Finished Width and Height of the Cornice.


C.O.M. YARDAGE REQUIREMENTS FOR CORNICE WITH CUSTOM SHAPED BANDING


The 1/4" or 3/8" Cording will also outline the Flat Custom Designed Shaped Banding. Yardage has been

YC101, July 2010


CORDED HARD CORNICE:Straight cornice with 4 rows of 1" jumbo cording with corner knotsFour Rows of 1" Jumbo Cording with corner knots at ends (included).

C.O.M. Yardage Requirement - Hard Corded CorniceAll yardages are based on a RETURN of up to 6". Please add 1 additional yard if your RETURN is between 6" and 9".The Finished Width of the Cornice Equals the Boardface Measurement Plus Two Returns.

Finished Width > 25" to 36" 37" to 48" 49" to 60" 61" to 72" 73" to 84" 85" to 96" 97" to 108"Finished Height \/ (1) (1) (1) (1) (2) (2) (2)

Up to 10" 1.25 1.25 1.25 1.25 2.00 2.00 2.0010 1/4" to 14" 1.50 1.50 1.50 1.50 2.25 2.25 2.2514 1/4" to 18" 1.75 1.75 1.75 1.75 2.50 2.50 2.5018 1/4" to 21" 2.00 2.00 2.00 2.00 2.75 2.75 2.7521 1/4" to 24" 2.00 2.00 2.00 2.00 3.00 3.00 3.00

JUMBO CORD: 1.00 1.00 1.25 1.25 1.50 1.75 1.75

CORDED SOFT CORNICE:Four Rows of 1" Jumbo Cording with corner knots at ends (included).Decorative top to be mounted at the top of shades or valances.

C.O.M. Yardage Requirement - Soft Corded CorniceAll yardages are based on a RETURN of up to 6". Please add 1 additional yard if your RETURN is between 6" and 9".The Finished Width of the Cornice Equals the Boardface Measurement Plus Two Returns.Finished Width > 25" to 36" 37" to 48" 49" to 60" 61" to 72" 73" to 84" 85" to 96" 97" to 108"Finished Height \/ (1) (1) (1) (1) (2) (2) (2)

Overall FL approx 5" 1.00 1.00 1.25 1.25 1.50 1.75 1.75


CORNICESC.O.M. YARDAGE REQUIREMENTS FOR CORDED CORNICES

YC102, July 2010


Includes cording at top and down sides & across bottom of shaped area.

ALLOWANCE:Board face + 4 returns + 8" work divided by fabric width = # cuts needed.Cornice depth (to long point) + size of return (to cover top) + 6" work = cut length

ADD cording allowance: Cornice face width + 2 returns x 2 1/2 + (long point x 2) divided by 280" bias cuts = yardage needed



Finished Width > 25" to 36" 37" to 48" 49" to 60" 61" to 72" 73" to 84" 85" to 96" 97" to 108"

Finished Height \/ (1) (1) (1) (1) (2) (2) (2)

Up to 10" 1.75 1.75 2.50 2.50 3.00 3.25 3.25

10 1/4" to 14" 2.50 2.50 2.75 2.75 3.25 3.50 3.50

14 1/4" to 18" 2.50 2.50 2.75 2.75 4.00 4.00 4.25

18 1/4" to 21" 2.75 2.75 3.00 3.00 4.25 4.25 4.50

21 1/4" to 24" 3.00 3.00 3.25 3.25 4.50 4.50 4.75




CORNICESC.O.M. YARDAGE REQUIREMENTS FOR PAGODA CORNICES

C.O.M. Yardage Requirement

YC103, July 2010


See AF-1 Straight Cornice and Swags & Cascade for pricing.Straight cornice with swags & cascades attached.Specify Traditional or Open swags and if cascades are Traditional or Stacked.Specify if cascades over or under swags.Mounting charges for swags and cascades are additional.Pictured with Open Swags and Traditional Cascades.

ALLOWANCE: CORNICEBoard face + 4 returns + 8" work divided by fabric width = # cuts needed.Cornice depth (to long point) + size of return (to cover top) + 6" work = cut length


CORNICES: Finished Width > Up to 24" 25" to 36" 37" to 48" 49" to 60" 61" to 72" 73" to 84" 85" to 96"

97" to 108"

109" to 126"


ALLOWANCES: TRADITIONAL & OPEN SWAGS20" to 26" wide x 12" to 14" drop 1 yards for first swag27" to 46" wide x 14" to 21" drop 2 yards for first swag

1 1/2 yards each add'l swag46" to 55" wide x 14" to 21" drop 2 yards for each swagOver 55" wide OR over 21" drop Swag width + swag drop x 1 1/2 divided by 36 = yds each swag

CASCADE YARDAGE:Face Width of Cascades (YARDAGE includes 6" return)**Length of Cascade

\/ 6" (1) 8" (1) 10" (1) 12" (1) 14" (1)FACE FABRIC

Up to 36" 2.25 2.25 2.25 2.25 2.2572" 4.25 4.25 4.25 4.25 4.25

100" 9.00 9.00 9.00 9.00 9.00

CONTRAST FABRICUp to 36" 2.25 2.25 2.25 2.25 2.25

72" 4.25 4.25 4.25 4.25 4.25100" 9.00 9.00 9.00 9.00 9.00


CORNICES

C.O.M. Yardage Requirements

C.O.M. YARDAGE REQUIREMENTS FOR SWAGGED CORNICES

YC104, July 2010


ALLOWANCES:Width: Board face + 4 returns + 10" (work) divided by width of fabric = # of cuts needed. If only 2 cuts are needed, both cuts will be cut at the longest point. If more than 2 cuts are needed, the center cuts will be cut at the short point, the leg cuts will be cut at the long point.


CANTONEERS:

# of FEET > Up to 24" 25" to 36" 37" to 48" 49" to 60" 61" to 72" 73" to 84" 85" to 96"97" to 108"

109" to 126"

Finished Height \/ (1) (1) (1) (1) (1) (2) (2) (2) (2)Short Point/Long Point

18"/Up to 36" 2.75 2.75 2.75 2.75 2.75 3.75 3.75 3.75 3.7518"/36 1/4" to 42" 3.25 3.25 3.25 3.25 3.25 4.00 4.00 4.00 4.0018"/42 1/4" to 48" 3.50 3.50 3.50 3.50 3.50 4.25 4.25 4.25 4.2518"/48 1/4" to 54" 3.75 3.75 3.75 3.75 3.75 4.75 4.75 4.75 4.7518"/54 1/4" to 60" 4.25 4.25 4.25 4.25 4.25 5.00 5.00 5.00 5.00



109" to 126"

Finished Height \/ (1) (1) (1) (1) (1) (2) (2) (2) (2)Short Point/Long Point

18" sp /66" lp 4.50 4.50 4.50 4.50 4.50 5.25 5.25 5.25 5.2518" sp /72" lp 4.75 4.75 4.75 4.75 4.75 5.75 5.75 5.75 5.7518" sp /78" lp 5.25 5.25 5.25 5.25 5.25 6.00 6.00 6.00 6.0018" sp /84" lp 5.50 5.50 5.50 5.50 5.50 6.25 6.25 6.25 6.2518" sp /90" lp 5.75 5.75 5.75 5.75 5.75 6.75 6.75 6.75 6.7518" sp /96" lp 6.25 6.25 6.25 6.25 6.25 7.00 7.00 7.00 7.00

18" sp /102" lp 6.50 6.50 6.50 6.50 6.50 7.25 7.25 7.25 7.2518" sp /108" lp 6.75 6.75 6.75 6.75 6.75 7.75 7.75 7.75 7.75


All yardages are based on a RETURN of up to 6". Please add 1 additional yard if your RETURN is between 6" and 9".NOTE: Cantoneers are shipped in one piece. Possible Truck Freight charges may be added.Lambrequins are shipped in 3 pieces unless requested to ship in 1 piece. Truck freight charges may need to be added.The 1/4" or 3/8" Cording Yardage (on shaded line) MUST be added to the yardage amount for TOTAL FABRIC yardage.54" SOLID FABRICS have been used for all yardage estimates. For repeats, multiply your repeat size times the number in parenthesis, divide by 36 and add this amount to the yardage listed in the chart. Overages may be possible. Please call if you would like assistance.

CORNICESC.O.M. YARDAGE REQUIREMENTS FOR

CANTONEERS & LAMBREQUINS


LAMBREQUINS:

YC105, July 2010

SHHADDESS CHHARTSTS

ANDERSON FABRIC WORKROOM SHADES

ALLOWANCES:Width: (Unlined) Board face + returns x 1 1/2 (fullness) + 2 1/2" (side hems) divided by fabric width = # of cuts.

Width: (Lined) Board face + returns x 1 1/2 (fullness) + 5" (side hems) divided by fabric width = # of cuts.

Length: Finished length (short point) (x 3 if sheer fabric) or (x 2 1/2 medium wt. fabric) = cut length.


109" to 126"

Finished Length \/ (0) (1) (1) (1) (2) (2) (2) (3) (3)up to 24" 2.25 4.25 4.25 4.25 6.25 6.25 6.25 8.25 8.25

30" 2.75 5.25 5.25 5.25 7.75 7.75 7.75 10.25 10.2536" 3.25 6.25 6.25 6.25 9.25 9.25 9.25 12.25 12.2542" 3.75 7.25 7.25 7.25 10.75 10.75 10.75 14.25 14.2548" 4.25 8.25 8.25 8.25 12.25 12.25 12.25 16.25 16.2554" 4.75 9.25 9.25 9.25 13.75 13.75 13.75 18.25 18.2560" 5.25 10.25 10.25 10.25 15.25 15.25 15.25 20.25 20.2566" 5.75 11.25 11.25 11.25 16.75 16.75 16.75 22.25 22.2572" 6.25 12.25 12.25 12.25 18.25 18.25 18.25 24.25 24.2578" 6.75 13.25 13.25 13.25 19.75 19.75 19.75 26.25 26.2584" 7.25 14.25 14.25 14.25 21.25 21.25 21.25 28.25 28.2590" 7.75 15.25 15.25 15.25 22.75 22.75 22.75 30.25 30.25 96" 8.25 16.25 16.25 16.25 24.25 24.25 24.25 32.25 32.25

54" SOLID FABRICS at 1 1/2x fullness have been used for yardage estimates. For repeats, multiply your repeat size times the number in parenthesis, divide by 36 and add this amount to the yardage listed in the chart. Overages may be possible. Please call if you would like assistance.


SHADESC.O.M. YARDAGE REQUIREMENTS FOR AUSTRIAN SHADES

OR VALANCES

YC106, July 2010


Cloud Petticloud

Balloon Pettiloon

ALLOWANCES:Width: Board face + returns x 3 (fullness) + 6" (side hems) divided by fabric width = # of cuts needed. Length: Finished length (short point) + 22" (lined) + 26" (unlined) = cut length.

Sheer or lace fabrics: Short point + 30" = cut length

C.O.M. YARDAGE REQUIREMENTSThis yardage chart is based on lined shades or valances using 3 x fullness


126"Finished Length (1) (2) (2) (3) (4) (4) (5) (6) (7)at Short Point \/

up to 24" 3.00 4.25 4.25 5.75 7.00 7.00 8.50 9.75 11.2530" 3.25 4.75 4.75 6.25 8.00 8.00 9.50 11.00 12.5036" 3.50 5.25 5.25 7.00 8.75 8.75 10.50 12.25 14.0042" 4.00 5.75 5.75 7.75 9.50 9.50 11.50 13.25 15.2548" 4.25 6.25 6.25 8.25 10.50 10.50 12.50 14.50 16.5054" 4.50 6.75 6.75 9.00 11.25 11.25 13.50 15.75 18.0060" 5.00 7.25 7.25 9.75 12.00 12.00 14.50 16.75 19.2566" 5.25 7.75 7.75 10.25 13.00 13.00 15.50 18.00 20.5072" 5.50 8.25 8.25 11.00 13.75 13.75 16.50 19.25 22.0078" 6.00 8.75 8.75 11.75 14.50 14.50 17.50 20.25 23.2584" 6.25 9.25 9.25 12.25 15.50 15.50 18.50 21.50 24.5090" 6.50 9.75 9.75 13.00 16.25 16.25 19.50 22.75 26.00 96" 7.00 10.25 10.25 13.75 17.00 17.00 20.50 23.75 27.25


SHADESC.O.M. YARDAGE REQUIREMENTS FOR ALL BALLOONS, CLOUDS,

& PETTILOON SHADES OR VALANCES

YC107, July 2010


Flat Roman Valance

Flat Fold Roman Warm Window

ALLOWANCES: Width: Board face + 6" (side hems) divided by fabric width = # of cuts needed. Length: Finished length + 16" = cut length.


109" to 126"


30" 1.50 1.50 1.50 2.75 2.75 2.75 2.75 4.00 4.0036" 1.50 1.50 1.50 3.00 3.00 3.00 3.00 4.50 4.5042" 1.75 1.75 1.75 3.25 3.25 3.25 3.25 5.00 5.0048" 2.00 2.00 2.00 3.75 3.75 3.75 3.75 5.50 5.5054" 2.00 2.00 2.00 4.00 4.00 4.00 4.00 6.00 6.0060" 2.25 2.25 2.25 4.25 4.25 4.25 4.25 6.50 6.5066" 2.50 2.50 2.50 4.75 4.75 4.75 4.75 7.00 7.0072" 2.50 2.50 2.50 5.00 5.00 5.00 5.00 7.50 7.5078" 2.75 2.75 2.75 5.25 5.25 5.25 5.25 8.00 8.0084" 3.00 3.00 3.00 5.75 5.75 5.75 5.75 8.50 8.5090" 3.00 3.00 3.00 6.00 6.00 6.00 6.00 9.00 9.00 96" 3.25 3.25 3.25 6.25 6.25 6.25 6.25 9.50 9.50


12 1/2" to 18" 1.25 1.25 1.25 2.25 2.25 2.25 2.25 3.25 3.2518 1/2" to 24" 1.25 1.25 1.25 2.50 2.50 2.50 2.50 3.75 3.75


SHADES OR VALANCES

C.O.M. YARDAGE REQUIREMENT-FLAT FOLD & WARM WINDOW SHADES

C.O.M. YARDAGE REQUIREMENTS FOR FLAT ROMAN SHADES, FLAT ROMAN VALANCES & WARM WINDOW ROMAN SHADES

C.O.M. YARDAGE REQUIREMENT-FLAT ROMAN VALANCE

YC108, July 2010


ALLOWANCES: Relaxed Flat RomanWidth: Board face + 6" (side hems) divided by fabric width = # of cuts. Length: Finished length + 40" = cut length.

ALLOWANCES: Relaxed Pleated RomanWidth: Board face + 10" pleat + 6" side hems divided by fabric width = # cuts. Length: Finished length + 40" = cut length.

ALLOWANCES: Straight Bottom Flap (specify length of flap)Width: Board face + 6" (side hems) divided by fabric width = # of cuts needed. Length: Finished length of flap x 2 + 7" (work) = cut length.


109" to 126"

Finished Length (0) (0) (0) (1) (1) (1) (1) (2) (2)at Long Point \/

up to 24" 2.00 2.00 2.00 4.00 4.00 4.00 4.00 5.50 5.5030" 2.00 2.00 2.00 4.00 4.00 4.00 4.00 6.00 6.0036" 2.50 2.50 2.50 4.50 4.50 4.50 4.50 6.50 6.5042" 2.50 2.50 2.50 5.00 5.00 5.00 5.00 7.00 7.0048" 2.50 2.50 2.50 5.00 5.00 5.00 5.00 7.50 7.5054" 3.00 3.00 3.00 5.50 5.50 5.50 5.50 8.00 8.0060" 3.00 3.00 3.00 6.00 6.00 6.00 6.00 8.50 8.5066" 3.00 3.00 3.00 6.00 6.00 6.00 6.00 9.00 9.0072" 3.50 3.50 3.50 6.50 6.50 6.50 6.50 9.50 9.5078" 3.50 3.50 3.50 7.00 7.00 7.00 7.00 10.00 10.0084" 3.50 3.50 3.50 7.00 7.00 7.00 7.00 10.50 10.5090" 4.00 4.00 4.00 7.50 7.50 7.50 7.50 11.00 11.00 96" 4.00 4.00 4.00 8.00 8.00 8.00 8.00 11.50 11.50


up to 24" 2.00 2.00 4.00 4.00 4.00 4.00 5.50 5.50 5.5030" 2.00 2.00 4.00 4.00 4.00 4.00 6.00 6.00 6.0036" 2.50 2.50 4.50 4.50 4.50 4.50 6.50 6.50 6.5042" 2.50 2.50 5.00 5.00 5.00 5.00 7.00 7.00 7.0048" 2.50 2.50 5.00 5.00 5.00 5.00 7.50 7.50 7.5054" 3.00 3.00 5.50 5.50 5.50 5.50 8.00 8.00 8.0060" 3.00 3.00 6.00 6.00 6.00 6.00 8.50 8.50 8.5066" 3.00 3.00 6.00 6.00 6.00 6.00 9.00 9.00 9.0072" 3.50 3.50 6.50 6.50 6.50 6.50 9.50 9.50 9.5078" 3.50 3.50 7.00 7.00 7.00 7.00 10.00 10.00 10.0084" 3.50 3.50 7.00 7.00 7.00 7.00 10.50 10.50 10.5090" 4.00 4.00 7.50 7.50 7.50 7.50 11.00 11.00 11.00 96" 4.00 4.00 8.00 8.00 8.00 8.00 11.50 11.50 11.50

Bottom Flap (to 7") 1.00 1.00 1.00 1.25 1.25 1.25 1.25 1.75 1.75

SHADESC.O.M. YARDAGE REQUIREMENTS FOR RELAXED FLAT FOLD &

RELAXED PLEATED ROMAN

C.O.M. YARDAGE REQUIREMENT-RELAXED FLAT ROMAN

C.O.M. YARDAGE REQUIREMENT-RELAXED PLEATED ROMAN

YC109, July 2010


Flat Stitched

Slatted

ALLOWANCES: FLAT STITCHED & SLATTED ROMANWidth: Board face + 6" (side hems) divided by fabric width = # cuts needed

Length: UP TO 54" FINISHED LENGTHFinished length + 36" = cut length.

Length: OVER 54" FINISHED LENGTHFinished length + 54" = cut length.


109" to 126"


30" 2.00 2.00 2.00 3.75 3.75 3.75 3.75 5.75 5.7536" 2.25 2.25 2.25 4.25 4.25 4.25 4.25 6.25 6.2542" 2.25 2.25 2.25 4.50 4.50 4.50 4.50 6.75 6.7548" 2.50 2.50 2.50 4.75 4.75 4.75 4.75 7.25 7.2554" 2.75 2.75 2.75 5.25 5.25 5.25 5.25 7.75 7.7560" 3.25 3.25 3.25 6.50 6.50 6.50 6.50 9.75 9.7566" 3.50 3.50 3.50 6.75 6.75 6.75 6.75 10.25 10.2572" 3.75 3.75 3.75 7.25 7.25 7.25 7.25 10.75 10.7578" 3.75 3.75 3.75 7.50 7.50 7.50 7.50 11.25 11.2584" 4.00 4.00 4.00 7.75 7.75 7.75 7.75 11.75 11.7590" 4.25 4.25 4.25 8.25 8.25 8.25 8.25 12.25 12.25 96" 4.25 4.25 4.25 8.50 8.50 8.50 8.50 12.75 12.75


SHADESC.O.M. YARDAGE REQUIREMENTS FOR ALL FLAT STITCHED

ROMANS OR SLATTED ROMANS


YC110, July 2010


ALLOWANCES:Width: Board face + 6" (side hems) divided by fabric width = # of cuts needed. Length: Finished length (mid-point) + 36" = cut length.

Tie Allowance: Tie Width x 3; Tie Length x 2 + 1" (add to the Face Fabric Yardage).(allow 1 yard per pair of ties; standardly 1 pair per shade/valance)Bow Allowance: 25" per Bow (MUST be added to Face Fabric Yardage).


126"Finished Length \/ (0) (0) (0) (1) (1) (1) (1) (1) (2)

up to 24" 2.00 2.00 2.00 3.50 3.50 3.50 3.50 5.50 5.5030" 2.00 2.00 2.00 4.00 4.00 4.00 4.00 5.50 5.5036" 2.00 2.00 2.00 4.00 4.00 4.00 4.00 6.00 6.0042" 2.50 2.50 2.50 4.50 4.50 4.50 4.50 6.50 6.5048" 2.50 2.50 2.50 5.00 5.00 5.00 5.00 7.00 7.0054" 2.50 2.50 2.50 5.00 5.00 5.00 5.00 7.50 7.5060" 3.00 3.00 3.00 5.50 5.50 5.50 5.50 8.50 8.5066" 3.00 3.00 3.00 6.00 6.00 6.00 6.00 8.50 8.5072" 3.00 3.00 3.00 6.00 6.00 6.00 6.00 9.00 9.0078" 3.50 3.50 3.50 6.50 6.50 6.50 6.50 9.50 9.5084" 3.50 3.50 3.50 7.00 7.00 7.00 7.00 10.00 10.0090" 3.50 3.50 3.50 7.00 7.00 7.00 7.00 10.50 10.50 96" 4.00 4.00 4.00 7.50 7.50 7.50 7.50 11.00 11.00

54" SOLID FABRICS have been used for all fabric yardages. For repeats, multiply your repeat measurement by the number in the parenthesis, divide by 36, and then add to the listed solid yardage. It may be possible that overages will occur with certain repeats. Please call if you would like assistance.

SHADES

C.O.M. YARDAGE REQUIREMENTS FOR FLAT TIED ROMANS


YC111, July 2010


Francine

Lundberg

ALLOWANCES:BOARD FACE UP TO 55" WIDE: (standardly 1 center pouf, 2 pleats)Width: Board face + 2 returns + 16" + 6" (side hems) divided by fabric width = # of cuts needed.

BOARD FACE OVER 55" WIDE: (one more pleat than # poufs)Width: Board face + 2 returns + 8" per pleat + 6" (side hems) divided by fabric width = # of cuts

Length: Finished length (mid point) + 40" = cut length.


126"Finished Length (0) (1) (1) (1) (1) (1) (2) (2) (2)at Mid-Point \/

up to 24" 2.00 4.00 4.00 4.00 4.00 4.00 5.50 5.50 5.5030" 2.00 4.00 4.00 4.00 4.00 4.00 6.00 6.00 6.0036" 2.50 4.50 4.50 4.50 4.50 4.50 6.50 6.50 6.5042" 2.50 5.00 5.00 5.00 5.00 5.00 7.00 7.00 7.0048" 2.50 5.00 5.00 5.00 5.00 5.00 7.50 7.50 7.5054" 3.00 5.50 5.50 5.50 5.50 5.50 8.00 8.00 8.0060" 3.00 6.00 6.00 6.00 6.00 6.00 8.50 8.50 8.5066" 3.00 6.00 6.00 6.00 6.00 6.00 9.00 9.00 9.0072" 3.50 6.50 6.50 6.50 6.50 6.50 9.50 9.50 9.5078" 3.50 7.00 7.00 7.00 7.00 7.00 10.00 10.00 10.0084" 3.50 7.00 7.00 7.00 7.00 7.00 10.50 10.50 10.5090" 4.00 7.50 7.50 7.50 7.50 7.50 11.00 11.00 11.00 96" 4.00 8.00 8.00 8.00 8.00 8.00 11.50 11.50 11.50



SHADES or VALANCES

C.O.M. YARDAGE REQUIREMENTS FOR FRANCINE & LUNDBERG

YC112, July 2010


ALLOWANCES:Width: Board face + 6" (side hems) divided by fabric width = # of cuts.

Length: UP TO 54" FINISHED LENGTHFinished length x 2 + 18" = cut length.

Length: OVER 54" FINISHED LENGTH Finished length x 2 + 24" = cut length.



109" to 126"


30" 2.25 2.25 2.25 4.50 4.50 4.50 4.50 6.75 6.7536" 2.75 2.75 2.75 5.25 5.25 5.25 5.25 7.75 7.7542" 3.00 3.00 3.00 5.75 5.75 5.75 5.75 8.75 8.7548" 3.25 3.25 3.25 6.50 6.50 6.50 6.50 9.75 9.7554" 3.75 3.75 3.75 7.25 7.25 7.25 7.25 10.75 10.7560" 4.25 4.25 4.25 8.25 8.25 8.25 8.25 12.25 12.2566" 4.50 4.50 4.50 8.75 8.75 8.75 8.75 13.25 13.2572" 4.75 4.75 4.75 9.50 9.50 9.50 9.50 14.25 14.2578" 5.25 5.25 5.25 10.25 10.25 10.25 10.25 15.25 15.2584" 5.50 5.50 5.50 10.75 10.75 10.75 10.75 16.25 16.2590" 5.75 5.75 5.75 11.50 11.50 11.50 11.50 17.25 17.25 96" 6.25 6.25 6.25 12.25 12.25 12.25 12.25 18.25 18.25


SHADES

C.O.M. YARDAGE REQUIREMENTS FOR HOBBLED ROMANS

YC113, July 2010


ALLOWANCES:Width: Board face + returns x 3 (fullness) + 6" (side hems) divided by fabric width = # of cuts needed. Length: Finished length (long point) x 2 = cut length.


109" to 126"


Up to 30" 3.50 5.00 5.00 7.00 8.50 8.50 10.00 12.00 13.5030 1/4" to 36" 4.00 6.00 6.00 8.00 10.00 10.00 12.00 14.00 16.0036 1/4" to 42" 5.00 7.00 7.00 9.50 12.00 12.00 14.00 16.50 19.0042 1/4" to 48" 5.50 8.50 8.50 11.00 13.50 13.50 16.50 19.00 21.5048 1/4" to 54" 6.00 9.00 9.00 12.00 15.00 15.00 18.00 21.00 24.0054 1/4" to 60" 7.00 10.00 10.00 13.50 17.00 17.00 20.00 23.50 27.00


Possible Truck Freight Because of Finished Width.No EXTRA Options Are Available on the Opera Topper Stationary Valance.

SHADES


C.O.M. YARDAGE REQUIREMENTS FOR OPERA TOPPERS

YC114, July 2010


BAND TIE

ALLOWANCES:Width: Board face width (+ 2 returns, if any) + 6" side hems divided by fabric width = # cuts needed.

Length: (Select the correct formula for the type of valance being made.)Self-lined Valance & Self-lined roll: Regular lined Valance & Self-lined roll:Finished length + 16 1/2" x 2 = cut length. Finished length + 32 1/2" = cut length (includes self-lined

roll cuts.)Contrast lined Valance & Contrast roll: Regular lined Valance & Contrast roll:Finished length + 17 1/2" = cut length of face Finished length + 18" = cut length of face.Finished length + 17 1/2" = cut length of Finished length + 3 1/2" = cut length of regular liningcontrast lining. Cut length of contrast roll = 16"

TIES: Allow 1 yard per pair.

C.O.M. YARDAGE REQUIREMENT - Self-Lined Valances


109" to 126"

Finished Length \/ (0) (0) (0) (1) (1) (1) (1) (2) (2)Up to 12" 2.00 2.00 2.00 3.75 3.75 3.75 3.75 5.50 5.50Up to 18" 2.25 2.25 2.25 4.25 4.25 4.25 4.25 6.50 6.50Up to 24" 2.50 2.50 2.50 5.00 5.00 5.00 5.00 7.50 7.50


109" to 126"

Finished Length \/ (0) (0) (0) (1) (1) (1) (1) (2) (2)Up to 12" 1.00 1.00 1.00 2.00 2.00 2.00 2.00 2.75 2.75Up to 18" 1.25 1.25 1.25 2.25 2.25 2.25 2.25 3.25 3.25Up to 24" 1.25 1.25 1.25 2.50 2.50 2.50 2.50 3.75 3.75

C.O.M. YARDAGE REQUIREMENT - Contrast Lined Valances

SHADESC.O.M. YARDAGE REQUIREMENTS FOR

ROLLED STAGECOACH VALANCES

STAGECOACH TIE BOW TIE

YC115, July 2010


BOW TIE

SONESTA VALANCE

ALLOWANCES:Width: Board face + returns + 6" (side hems) divided by fabric width = # of cutsLength: Finished length x 2 + 18" = cut length.TIES: Allow 1 yard per pair.


109" to 126"

Finished Length \/ (0) (0) (0) (1) (1) (1) (1) (2) (2)Up to 12" 1.25 1.25 1.25 2.50 2.50 2.50 2.50 3.75 3.75

18" 1.75 1.75 1.75 3.25 3.25 3.25 3.25 4.75 4.7524" 2.00 2.00 2.00 3.75 3.75 3.75 3.75 5.75 5.75

If you wish to have the side legs covered in face fabric, you must specify on your work order and supplyadditional yardage. Add 1 yard to the allowances above which will cover up to 24" length of treatment


BAND TIE

VALANCESC.O.M. YARDAGE REQUIREMENTS FOR STAGECOACH & SONESTA

VALANCES


STAGECOACH TIE

YC116, July 2010


ALLOWANCES: Width: Board face x 3 (fullness) + 2" (side hems) divided by fabric width = # cuts

Length: Finished length + 4" (2" double bottom hem) + 14" facing allowance + 2" (work) = cut length.

The following chart has been provided to assist you in figuring the number of widths needed for proper 3 times fullness.using 54" fabric.Use the rod face (bracket to bracket) measurement to determine the number of widths needed. Always round up to the nearest whole width.

Width of valance 20"-24" 24 1/4"-36" 36 1/4"-48" 48 1/4"-60" 60 1/4"-72" 72 1/4"-84" 84 1/4"-96" 108" 120"# of Widths 2 3 3 4 5 5 6 7 7


# of FEET 2 3 4 5 6 7 8 9 10# of Widths 2 (1) 3(2) 3(2) 4(3) 5(4) 5(4) 6(5) 7(6) 7(6)Up to 12" 2.00 2.75 2.75 3.75 4.50 4.50 7.25 6.25 6.2512 1/4" to 18" 2.25 3.25 3.25 4.25 5.50 5.50 6.50 7.50 7.5018 1/4" to 24" 2.50 3.75 3.75 5.00 6.25 6.25 7.50 8.75 8.75

# of FEET 2 3 4 5 6 7 8 9 10# of Widths 2 (1) 3(2) 3(2) 4(3) 5(4) 5(4) 6(5) 7(6) 7(6)1/4" cord @ Top 0.50 0.50 0.50 0.75 0.75 0.75 1.00 1.00 1.00Ties @ Top 0.50 0.50 1.00 1.00 1.00 1.50 1.50 1.50 2.0054" SOLID FABRICS have been used for all yardage estimates. For repeats, multiply your repeat size times the number in parenthesis, divide by 36 and add this amount to the yardage listed in the chart. Overages may be possible.

TOP TREATMENTS




C.O.M YARDAGE REQUIREMENTS FOR DIXIE VALANCE

YC38, July 2010

BEEDDDINGG CCHAARTTS

ANDERSON FABRIC WORKROOM BEDSPREADS

Common Bedspread Styles Available:

Throw serge Fitted serge Throw cord Fitted cord @ hem

Scalloped bottom Fitted cord @ mattress edge & hem

Throw styles with split corners: (splits @ bell corners, or at mattress edge must be specified).

split with bell corners split corners @ mattress edge

Other styles available: Box Fitted, Waterfall Fitted, Bedsacks

Standards:Bedspreads standardly have a 21" drop. Please specify. 14" drop is standard on coverletsStandard 15" pillow tuck on Twin & Full sizes, 20" pillow tuck on Queen & King sizes. Specify with or without pillow tuck.Bottom corners are rounded; Top corners are square on all bedspreadsHems are serged and blind-hemmed unless corded.

STANDARD BEDSPREAD SIZES:SIZE MATTRESS DROP FINISHED SIZETwin 39" x 75" 21" 81" x 111" (includes 15" pillow tuck)Full 54" x 75" 21" 96" x 111" (includes 15" pillow tuck)Queen 60" x 80" 21" 102" x 121" (includes 20" pillow tuck)King 78" x 80" 21" 120" x 121" (includes 20" pillow tuck)

STANDARD COVERLET SIZES:SIZE MATTRESS DROP FINISHED SIZETwin 39" x 75" 14" 67" x 104" (includes 15" pillow tuck)Full 54" x 75" 14" 82" x 104" (includes 15" pillow tuck)Queen 60" x 80" 14" 88" x 114" (includes 20" pillow tuck)King 78" x 80" 14" 106" x 114" (includes 20" pillow tuck)

OVERSIZE BEDSPREADS OR COVERLETS--over 125" Finished width or length

BEDDING PRODUCTSC.O.M YARDAGE REQUIREMENTS FOR QUILTED

BEDSPREADS & COVERLETS (non-reversible)

YC117, July 2010


Bedspread Yardage

Coverlet Yardage

Cording Yardage

Premade Trim Yardage (3 sides)

TWIN STANDARD THROW - Serged Hem 7.00 6.5081" X 111" - 1/4" or 3/8" Cording at Hem 7.00 6.50 1.00(bedspread) - 1/2" or 1" Cording at Hem 7.00 6.50 2.00

(1) - 1" Shirred Cord at Hem 7.00 6.50 4.00- C.O.M. Trim at Hem 7.00 7.00 8.50FITTED - Serged Hem 7.00 6.50

67" X 104" FITTED - 1/4" or 3/8" Cording at Hem 7.00 7.00 1.00(coverlet) FITTED with 1/4" or 3/8" Cording at Mattress Edge 8.00 7.50 1.00

(1) FITTED w/1/4" or 3/8" Cording at Mattress Edge & Hem 7.75 7.50 2.00

FULL STANDARD THROW - Serged Hem 7.00 6.50- 1/4" or 3/8" Cording at Hem 7.00 6.50 1.00

96" X 111" - 1/2" or 1" Cording at Hem 7.00 6.50 2.00(bedspread) - 1" Shirred Cord at Hem 7.00 6.50 4.00

(1) - C.O.M. Trim at Hem 7.00 7.00 9.00FITTED - Serged Hem 7.00 6.50

82" X 104" FITTED - 1/4" or 3/8" Cording at Hem 7.00 7.00 1.00(coverlet) FITTED with 1/4" or 3/8" Cording at Mattress Edge (2) 11.75 11.25 1.00

(1) FITTED w/1/4" or 3/8" Cording at Mattress Edge & Hem (2) 11.50 11.00 2.00

QUEEN STANDARD THROW - Serged Hem 11.25 7.00- 1/4" or 3/8" Cording at Hem 11.25 7.00 1.00





KING STANDARD THROW - Serged Hem 11.25 10.50- 1/4" or 3/8" Cording at Hem 11.25 10.50 1.00





SUPER STANDARD THROW - Serged Hem 12.50 12.00KING - 1/4" or 3/8" Cording at Hem 12.50 12.00 1.00

135" x 136" - 1/2" or 1" Cording at Hem 12.50 12.00 3.00(bedspread) - 1" Shirred Cord at Hem 12.50 12.00 4.00



(2) FITTED w/1/4" or 3/8" Cording at Mattress Edge & Hem (3) 18.25 17.75 2.0054" SOLID FABRICS have been used for all fabric yardages. For repeats, multiply your repeat measurement by the number in the parenthesis, divide by 36, and add to the yardage listed.

BEDDING PRODUCTS

Add the appropriate yardages for Cording or Fitted styles listed below to the Serged Hem style for total yardage.

C.O.M YARDAGE REQUIREMENTS FOR QUILTED BEDSPREADS & COVERLETS (non-reversible)

YC118, July 2010


ALLOWANCES:Top: Finished width + 4" divided by fabric width = # cuts needed for topFinished length + 4" = cut length of top

Canopy Skirt:(Finished width x 2) + (Finished length x 2) x 2 1/2 fullness divided by fabric width = # cuts for skirtSkirt drop + 6 1/2" = cut length of skirtDouble the yardage for self-lined.

Gathered Gathered Box Pleated Gathered CANOPY Skirt Skirt Skirt Skirt

SIZE Flat Top Arch Top Flat Top SunburstTwin Up to 12" Drop 8.00 9.75 9.50 25.25 All

(1) Contrast Lining 8.00 9.75 9.50 25.25 Canopies Full Up to 12" Drop 11.25 13.75 12.25 29.25 Are Lined.(1) Contrast Lining 11.25 13.75 12.25 29.25 Lining

Queen Up to 12" Drop 12.25 14.50 13.00 33.00 Fabric(1) Contrast Lining 12.25 14.50 13.00 33.00 is EXTRA.

King Up to 12" Drop 12.75 15.00 14.50 39.50(1) Contrast Lining 12.75 15.00 14.50 39.50

54" SOLID FABRICS have been used for all yardage estimates. For repeats, multiply your repeat size times the number in parenthesis divide by 36 and add this amount to the yardage listed in the chart. Overages may be possible. Please call if you would like assistance.


BEDDING PRODUCTSC.O.M YARDAGE REQUIREMENTS FOR BED CANOPIES

YC119, July 2010


ALLOWANCES:Width: Width of top + 2 drops = FINISHED WIDTH Finished width + 10" shrinkage divided by fabric width = # cuts each side (round up to whole #)Length:Length of top + 1 drop = FINISHED LENGTHFinished length + 14" shrinkage = CUT LENGTH

Front Back/Lining Premade 1" - 5" 5 1/4"- 8"Fabric Fabric Cording Trim Ruffling Ruffling

Yardage Yardage Yardage Yardage Yardage Yardage

TWIN - Pillowcased Edge 5.75 5.75- 1/4" or 3/8" Cording 5.75 5.75 1.00

- 1/2" or 1" Cording 5.75 5.75 2.0067" FW x 89" FL - 1" Shirred Cord 5.75 5.75 4.00

(1) - C.O.M.. Trim 5.75 5.75 8.00- Ruffling 5.75 5.75 4.75 7.00

FULL - Pillowcased Edge 5.75 5.75- 1/4" or 3/8" Cording 5.75 5.75 1.00- 1/2" or 1" Cording 5.75 5.75 2.00

82" FW x 89" FL - 1" Shirred Cord 5.75 5.75 4.00(1) - C.O.M. Trim 5.75 5.75 8.50

- Ruffling 5.75 5.75 4.75 7.00

QUEEN - Pillowcased Edge 6.00 6.00- 1/4" or 3/8" Cording 6.00 6.00 1.00- 1/2" or 1" Cording 6.00 6.00 2.00


- Ruffling 6.00 6.00 5.00 7.50

KING - Pillowcased Edge 9.00 9.00- 1/4" or 3/8" Cording 9.00 9.00 1.00- 1/2" or 1" Cording 9.00 9.00 2.00


- Ruffling 9.00 9.00 5.50 8.00

CALIFORNIA - Pillowcased Edge 9.50 9.50KING - 1/4" or 3/8" Cording 9.50 9.50 1.00

- 1/2" or 1" Cording 9.50 9.50 2.00100" FW x 98" FL - 1" Shirred Cord 9.50 9.50 4.00

(2) - C.O.M. Trim 9.50 9.50 9.50- Ruffling 9.50 9.50 5.50 8.00

* Maximum Comforter size: 125" finished width x 125" finished length.54" SOLID FABRICS have been used for all yardage estimates. For repeats, multiply your repeat size times the number in parenthesis divide by 36 and add this amount to the yardage listed in the chart. Overages may be possible.

BEDDING PRODUCTS

Add the appropriate yardages for "extras" to the pillowcased edge amount for total

yardages.

C.O.M YARDAGE REQUIREMENTS FOR QUILTED COMFORTERS (reversible)

YC120, July 2010


Fabric Cording Ruffling TrimCRIB STANDARD THROW - Serged Hem 2.00

BEDSPREADS 1/4" or 3/8" Cording at Hem 0.50

28" wide x 52" long C.O.M. Trim at Hem 5.00

Up to 5" Self-lined ruffle 2.75

CRIB STANDARD THROW - Pillowcased 2.00

COMFORTERS 1/4" or 3/8" Cording at Hem 0.50

28" wide x 52" long C.O.M. Trim at Hem 5.00

Up to 5" Self-lined ruffle 2.75

Gathered or Gathered or

Box Pleated Box Pleated Tailored Tailored

CRIB (Includes band on platform) 5.25 (7) 5.25 (7) 4.00 (5) 4.00 (5)

DUST RUFFLES Skirt Lining (not included) 4.75 3.50

28" x 52" x 12" dropp

(Including tack strip) 5.25 5.25 4.00 4.00

Fabric Cording Ruffling Trim

BUMPER PADS Knife Edge 3.00

28" x 52" x 10" highStraight bumper pad, Quilted,

Knife Edge 4.75

(7) 1/4" or 3/8" cord @ top only 0.50

Premade trim @ top only 5.00

Up to 5" self-lined ruffle (top only) 3.00

(send template) estimate

1/4" cord and Up to 5" self-lined ruffle 0.50 3.00

DIAPER STACKERSDiaper stackers are made to fit most standard diapers. Unless custom pattern is supplied, the workroom will fabricate to

our standard size.

ALLOWANCE: 4 yards per standard diaper stacker.

BEDDINGC.O.M YARDAGE REQUIREMENTS FOR BABY CRIB ENSEMBLES

YC121, July 2010


DAYBED BEDSPREADS, COVERLETS & COMFORTERS:21" drop standard on all Bedspreads; 14" drop standard on all coverlets.14" drop standard on all comforters.Standard daybeds are 3-sided with a 4" back flap.Fitted styles available only on Bedspreads & Coverlets only.

STANDARD DAYBED BEDSPREAD SIZES:MATTRESS DROP FINISHED SIZE75" x 39" 21" 117" x 64" (includes 4" back flap)

STANDARD DAYBED COVERLET SIZES:MATTRESS DROP FINISHED SIZE75" x 39" 14" 103" x 57" (includes 4" back flap)

STANDARD DAYBED COMFORTER SIZES:MATTRESS DROP FINISHED SIZE75" x 39" 14" 103" x 57" (includes 4" back flap)

MEASURING TIPS:Always measure with bedding (blankets, sheets, etc.)Measure from top edge to desired length (allow for clearance).

ALLOWANCES:Width: Width of top + 2 drops = Finished width + 10% shrinkage + 4" (serged edge) + 2" (corded edge) divided by fabric width = # cuts needed (round up to whole number)

Length: Length of top + 1 drop + 4" back flap = Finished length + 10" shrinkage + 4" (serged edge) + 2" (corded edge) = cut length.

DAYBED DUST RUFFLES3 styles available: Gathered, Box Pleated or Tailored. Please specify style.Standardly made as 3-sided. (Please indicate if 4-sided is wanted)Split corners on Gathered & Box PleatedPlatform lining and banding on the platform are included. (skirt lining is additional)

STANDARD DAYBED DUST RUFFLE SIZES:WIDTH & LENGTH DROP75" wide x 39" long 14"

ALLOWANCES:Gathered & Box Pleated Width + Length + Length x 2 1/2 fullness divided by fabric width = # cuts needed (round up to whole #) Drop + 6 1/2" = cut length.

TailoredWidth + Length + Length x 1 3/4 fullness divided by fabric width = # cuts needed (round up to whole #)Drop + 6 1/2" = cut length.

BEDDING PRODUCTSC.O.M YARDAGE REQUIREMENTS FOR

DAYBED PRODUCTS

YC122, July 2010


BEDSPREAD: 75" wide x 39" long x 21" drop (2) BEDSPREAD COVERLETCOVERLET: 75" wide x 39" long x 14" drop (2) YARDAGE YARDAGE

COMFORTER75" wide x 39" long x 14" drop (2) YARDAGE

Throw - Style only 6.00Yardage amount is for EACH side of the comforter

Extras YARDAGE Item #- 1/4" or 3/8" Cording at Hem 1.00 BS0701- 1/2" or 1" Cording at Hem 2.00 BS0703- 1" Shirred Cord at Hem 4.00 BS0704- C.O.M. Trim at Hem 7.00 EX1101A

Fitted: Available on FITTED - Serged Hem BS0904Bedspreads & FITTED - 1/4" or 3/8" Cording at Hem 1.00 BS0904 & BS0901Coverlets only. FITTED with 1/4" or 3/8" Cording at Mattress Edge 2.00 BS0904 & BS0702

FITTED w/1/4" or 3/8" Cording at Mattress Edge & Hem 4.00 BS0904 & BS0702

75" wide x 39" long x 14" drop (1) FABRIC LININGStandard w/4" band on platform 6.00 5.00- 4-Sided Dust Ruffle 7.50 6.50- Tack Strip with Velcro 5.00 5.00



Lining is not included in pricing for lined dust ruffles. (EXTRA CHARGE)

Throw - Serged Hem 6.506.00

Add the following extras to the THROW-STYLE yardage above


DAYBED PRODUCTS

DAYBED GATHERED DUST

RUFFLE

DAYBED TAILORED DUST

RUFFLE

DAYBED BOX PLEATED DUST

RUFFLE

DAYBED BEDSPREADS OR

COVERLETS

DAYBED COMFORTERS

DAYBED EXTRAS

YC123, July 2010


Gathered Box Pleated Tailored

ALLOWANCES:Width:Gathered & Box Pleated: Width + Length + Length x 2 1/2 fullness divided by fabric width = # cutsTailored: Width + Length + Length x 1 3/4 fullness divided by fabric width = # cuts 1" Pleated: Width + Length + Length x 3 fullness divided by fabric width = # cutsLength: Drop size + 6 1/2" = cut length * All yardages include the 4" banding on the platform.

TWIN Standard with 4" # cuts (rpts) # cuts (rpts)39" x 75" x 14" drop Band on Platform 6.50 9 (8) 5.50 4.00 5 (5) 3.00

4-Sided Dust Ruffle 7.50 11 (10) 6.50 6.00 7 (4) 5.00Tack Strip w/Velcro 6.50 9 (8) 5.50 4.00 5 (4) 3.00

FULL Standard with 4" # cuts (rpts) # cuts (rpts)54" x 75" x 14" drop Band on Platform 7.00 10 (9) 6.00 4.50 6 (5) 3.50

4-Sided Dust Ruffle 8.50 13 (12) 7.50 6.00 8 (7) 5.00Tack Strip w/Velcro 7.00 10 (9) 6 4.50 6 (5) 3.50

QUEEN Standard with 4" # cuts (rpts) # cuts (rpts)60" x 80" x 14" drop Band on Platform 7.50 11 (10) 6.50 4.50 6 (5) 3.50


KING Standard with 4" # cuts (rpts) # cuts (rpts)78" x 80"x 14" drop Band on Platform 8.00 12 (10) 7.00 4.50 6 (5) 3.50


Gathered Dust Ruffles are 2 1/2 times fullness. Box Pleated Dust Ruffles are 2 1/2 times fullness. 1" Pleated Dust Ruffles are 3 times fullness.Tailored dust ruffles are 1 3/4 times fullness & will have pleats at corners & center of each drop unless specified otherwise.54" SOLID FABRICS and standard sizes have been used for all fabric yardages. For repeats, multiply your repeat measurement by the number in the parenthesis, divide by 36, and then add to the listed solid yardages. It may be possible that overages will occur with certain repeats. Please call if you would like assistance.If cut length is less than the repeat size, all cuts will be at the repeat. Do not add additional yardage.(example: 20 1/2" cut length, 27" repeat; all cuts will be at 27".)

BEDDING PRODUCTSC.O.M YARDAGE REQUIREMENTS FOR DUST RUFFLES

TAILOREDSKIRT

LININGSKIRT

LININGGATHERED OR BOX PLEATED

YC124, July 2010


Width: Finished width + 4" divided by fabric width = # cuts (each side)Length: Finished length + 4" = cut length.

Front Fabric

Back Fabric

Flap Fabric Flange Cording Trim

Up to 6" Ruffle

TWIN - Pillowcased 5.25 5.25 1.25- 1/4" or 3/8" Cording 5.25 5.25 1.25 1.00

68" x 90" - 1/2" or 1" Cording 5.25 5.25 1.25 2.00(1) - 1" Shirred Cord 5.25 5.25 1.25 4.00

- C.O.M.. Trim 5.25 5.25 1.25 7.25- up to 6" Ruffling 5.25 5.25 1.25 5.00- 4" Flanged w/ 1/4" or 3/8" Cord 5.25 5.25 1.25 3.50 1.00

FULL - Pillowcased 5.25 5.25 1.25- 1/4" or 3/8" Cording 5.25 5.25 1.25 1.00

83" x 90" - 1/2" or 1" Cording 5.25 5.25 1.25 2.00(1) - C.O.M. Trim 5.25 5.25 1.25 7.50

- up to 6" Ruffling 5.25 5.25 1.25 5.25- 4" Flanged w/ 1/4" or 3/8" Cord 5.25 5.25 1.25 3.50 1.00

QUEEN - Pillowcased 5.50 5.50 1.25- 1/4" or 3/8" Cording 5.50 5.50 1.25 1.00



KING - Pillowcased 8.25 8.25 1.75- 1/4" or 3/8" Cording 8.25 8.25 1.75 1.00



CAL - Pillowcased 5.75 5.75 1.25KING - 1/4" or 3/8" Cording 5.75 5.75 1.25 1.00



Extras yardage must be added to the Front or Back fabrics for total yardage amounts.54" SOLID FABRICS have been used for all yardage estimates. For repeats, multiply your repeat size times the number in parenthesis divide by 36 and add this amount to the yardage listed in the chart. Overages may be possible. Please call if you would like assistance.

BEDDING PRODUCTS

ALLOWANCES: (unquilted)

C.O.M YARDAGE REQUIREMENTS FOR DUVET COVERS

YC125, July 2010


Simply send us a sketch and measurements of your custom design and we'll help you to create it for you!

BH109 Sleighbed: Standard with cording. Specify if "flat face" is wantedBH111 Tufted Roll: Standard tufted roll with cording.BH112 Boxed: Standard 2" depth of boxing with cording front & back of boxing.BH113 Tailored: No roll. Face of headboard is flush with "framing" with cording on the face, boxed edge.BH114 Crown: Standard 2" depth boxed edge with cording front & back of boxing.

BH101 - pictured w/no roll BH102 - pictured w/no roll

BH103 - pictured w/no roll

BH106 - pictured w/no roll BH107 - pictured w/no roll

BH114

Concealed legs are available on the (**) styles only and must be requested on the work order.If not specified on the order, the headboard will be made with the standard leg style.

BEDDING PRODUCTS

*ANDERSON FABRICS INVITES CUSTOM DESIGNS OR SHAPES FOR HEADBOARDS*

C.O.M YARDAGE REQUIREMENTS FOR HEADBOARDS

YC126, July 2010


Headboard yardages below include the headboard face and matching legs. Add appropriate columns together for total ydge.

Standard white blackout lining will be used on the back of headboard if not specified or if extra fabric is not allowed.

Quilted or Standard

Tufted Headboard

Unquilted Headboard

Deep Diamond

Tufted Headboard

Single Shirred Contour

Roll

Single Flat Contour

Roll

Single Pleated Contour

Roll

Single 1" Shirred

Cord

Shirred Double

Contour Roll

1/2" Cording Between Roll

& Headboard

Premade Trim

between Roll &

Headboard

BH100

TWIN 5.00 (4) 5.00 (4) 2.50 2.50 1.50 5.75 0.50 3.00

FULL 5.00 (4) 5.00 (4) 2.50 2.50 1.50 5.75 0.50 3.00

QUEEN 6.00 (5) 6.00 (5) 2.75 2.75 1.50 6.50 0.50 3.00

KING 7.50 (5) 7.50 (5) 3.00 3.00 1.50 7.25 0.50 4.00

TWIN 2.50 (0) 2.25 (0) 5.00 2.50 1.50 0.50 3.00

FULL 3.75 (1) 2.25 (1) 5.00 2.50 1.50 0.50 3.00

QUEEN 3.75 (1) 2.25 (1) 5.00 2.75 1.50 0.50 3.00

KING 5.00 (1) 3.50 (1) 6.75 3.00 1.50 0.50 4.00

BH103

TWIN 2.50 (0) 2.25 (0) 5.00 2.50 1.50 0.50 3.00

FULL 3.75 (1) 2.25 (1) 5.00 2.50 2.50 1.50 0.50 3.00

QUEEN 3.75 (1) 2.25 (1) 5.00 2.75 2.50 1.50 0.50 3.00

KING 5.00 (1) 3.50 (1) 6.75 3.00 3.75 1.50 0.50 4.00

BH104

TWIN 2.50 (0) 2.25 (0) 5.00 2.50 2.50 2.50 1.50 5.75 0.50 3.00

FULL 3.75 (1) 2.25 (1) 5.00 2.50 2.50 2.50 1.50 5.75 0.50 3.00

QUEEN 3.75 (1) 2.25 (1) 5.00 2.75 2.50 2.75 1.50 6.50 0.50 3.00

KING 5.00 (1) 3.50 (1) 6.75 3.00 3.75 3.00 1.50 7.25 0.50 4.00

BH105

TWIN 2.50 (0) 2.25 (0) 5.00 2.50 2.50 1.50 5.75 0.50 3.00

FULL 3.75 (1) 2.25 (1) 5.00 2.50 2.50 2.50 1.50 5.75 0.50 3.00

QUEEN 3.75 (1) 2.25 (1) 5.00 2.75 2.50 2.75 1.50 6.50 0.50 3.00

KING 5.00 (1) 3.50 (1) 6.75 3.00 3.75 3.00 1.50 7.25 0.50 4.00

BH106 & BH107

TWIN 2.50 (0) 2.25 (0) 5.00 2.50 1.50 0.50 3.00

FULL 3.75 (1) 2.25 (1) 5.00 2.50 1.50 0.50 3.00

QUEEN 3.75 (1) 2.25 (1) 5.00 2.75 1.50 0.50 3.00

KING 5.00 (1) 3.50 (1) 6.75 3.00 1.50 0.50 4.00

BH108

TWIN 2.50 (0) 2.25 (0) 5.00 2.50 2.50 2.50 1.50 5.75 0.50 3.00

FULL 3.75 (1) 2.25 (1) 5.00 2.50 2.50 2.50 1.50 5.75 0.50 3.00

QUEEN 3.75 (1) 2.25 (1) 5.00 2.75 2.50 2.75 1.50 6.50 0.50 3.00

KING 5.00 (1) 3.50 (1) 6.75 3.00 3.75 3.00 1.50 7.25 0.50 4.0054" SOLID FABRICS have been used for all fabric yardages. For repeats on the body of the Headboard, multiply your repeat measurementby the number in the parentheses, and then add to the listed solid yardage. It may be possible that overages will occur with certain repeats.You do not have to be concerned about repeats with the Contour roll or Extras yardages. Please call for assistance.* Full & Queen headboards without roll: add one yard additional (plus repeat)

BEDDING PRODUCTS

BH101 & BH102


YC127, July 2010


Headboard yardages below include the headboard face and matching legs. Add appropriate columns together for total ydge.

Standard white blackout lining will be used on the back of headboard if not specified or if extra fabric is not allowed.

Quilted or Unquilted 1/2" Cording Premade Trim

Standard Tufted Headboard Between Roll between Roll

Headboard & Headboard & Headboard

BH109

TWIN 5.25 (1) 2.00 6.00

FULL 5.25 (1) 2.00 6.00

QUEEN 5.25 (1) 2.00 6.00

KING 7.00 (2) 2.00 6.00

BH110

TWIN 3.50 (1) 2.00 7.00

FULL 3.75 (1) 2.00 7.50

QUEEN 3.75 (1) 2.00 7.50

KING 3.75 (2) 2.00 8.50

BH111

TWIN 2.50 (0) 2.00 6.50

FULL 3.75 (1) 2.00 7.00

QUEEN 3.75 (1) 2.00 7.00

KING 3.75 (1) 2.00 7.50

BH112

TWIN (1) 3.75 1.00 7.00

FULL (1) 4.00 1.00 8.00

QUEEN (1) 4.00 1.50 7.50

KING (2) 5.00 1.50 8.50

BH113

TWIN (1) 3.75 1.00 10.00

FULL (1) 4.00 1.00 12.00

QUEEN (1) 4.00 1.50 13.00

KING (2) 5.00 1.50 15.00

BH114

TWIN (1) 3.75 1.00 7.00

FULL (1) 4.00 1.00 8.00

QUEEN (1) 4.00 1.50 7.50

KING (2) 5.00 1.50 8.50

54" SOLID FABRICS have been used for all fabric yardages. For repeats on the body of the Headboard, multiply your repeat measurement by the number in parentheses, and then add to the listed solid yardage. Overages may be possible. You do not have to be concerned about repeats with the Contour Roll or Extras' yardages.Please call if you would like assistance.

BEDDING PRODUCTS


YC128, July 2010


Add the "extras" column to the sham body for total yardage when using

Unquilted or

Handguided Outline Quilting Fabric

needed for sham

BODY

HAUSER patterns Quilting Fabric

needed for sham

BODY

All EXTRAS

Fabric needed (add to sham body)

Envelope Style Sham

Fabric needed for

sham BODY

Envelope Style

EXTRAS Fabric needed (add to sham body)

Boxed Edge Style

Sham Fabric

needed for sham

BODY

Boxed Edge Style EXTRAS

Fabric needed (add to sham body)

TWIN - Knife Edge 1.50 2.00 2.50& FULL - 1/4" or 3/8" Cording 1.50 2.00 0.50 2.50 0.50 2.50 1.00

- 1/2" or 1" Jumbo Cording 1.50 2.00 0.50 2.50 0.50 2.50 1.0026" x 20" - 1" Shirred Cording 1.50 2.00 1.50 2.50 1.50 2.50 3.00

(1) - 3" Flanged 1.50 2.00 1.00 2.50 1.50 2.50 2.00- 4" Ruffled 1.50 2.00 1.50 2.50 1.50 2.50 3.00 - 1/4" or 3/8" Cord & Ruffling 1.50 2.00 2.00 2.50 2.00 2.50 4.00- C.O.M. Trim 1.50 2.00 3.00 2.50 4.00 2.50 5.50

QUEEN - Knife Edge 1.50 2.00 2.50- 1/4" or 3/8" Cording 1.50 2.00 0.50 2.50 0.50 2.50 1.00

30" x 20" - 1/2" or 1" Jumbo Cording 1.50 2.00 0.50 2.50 0.50 2.50 1.00(1) - 1" Shirred Cording 1.50 2.00 1.50 2.50 1.50 2.50 3.00

- 3" Flanged 1.50 2.00 1.00 2.50 1.50 2.50 2.00- 4" Ruffled 1.50 2.00 1.50 2.50 1.50 2.50 3.00 - 1/4" or 3/8" Cord & Ruffling 1.50 2.00 2.00 2.50 2.00 2.50 4.00- C.O.M. Trim 1.50 2.00 3.00 2.50 4.50 2.50 6.00

KING - Knife Edge 1.50 2.00 2.50- 1/4" or 3/8" Cording 1.50 2.00 0.50 2.50 0.50 2.50 1.00

36" x 20" - 1/2" or 1" Jumbo Cording 1.50 2.00 0.50 2.50 0.50 2.50 1.00(1) - 1" Shirred Cording 1.50 2.00 1.50 2.50 1.50 2.50 3.00

- 3" Flanged 1.50 2.00 1.00 2.50 1.50 2.50 2.00- 4" Ruffled 1.50 2.00 2.00 2.50 2.00 2.50 3.50 - 1/4" or 3/8" Cord & Ruffling 1.50 2.00 2.50 2.50 2.50 2.50 4.50- C.O.M. Trim 1.50 2.00 3.50 2.50 5.00 2.50 6.50

EURO Twin, Full ( 26" x 26") 1.50 2.00(1) Queen, King (26" x 26") 1.50 2.00

** Divide your repeat size by the size of your sham to figure the number of repeats needed per sham.54" SOLID FABRICS have been used for all yardage estimates. Please call if you would like assistance.

BODY PILLOW

SHAMStandard Size 70" x 35" 5.00 5.00

BEDDING PRODUCTSC.O.M YARDAGE REQUIREMENTS FOR PILLOW SHAMS


the same fabric.

YC129, July 2010


Unquilted bedspreads or coverlets are available in the following styles:Throw Style Fitted Style

Fitted w/cord @ mattress edge Fitted w/cord @ hem & mattress edge

Drop extends to the floor on bedspreads--standard drop 21".14" drop standard on all coverlets.Includes 15" to 20" pillow tuck. Reverse pillow tuck is also available if specified.

PLEASE NOTE: All unquilted bedspreads MUST BE "DRESSED". Fabric and lining will shift.

All unquilted bedspreads standard WITHOUT FILL. Seams will be pattern matched, serged & topstitched.Stitch line is visible on face. Stretchy fabrics will have seams lockstitched and press flat; no stitch lines on face.Hem is pillowcased and topstitched 1/2" on all four sides.

If fill is wanted, you will be billed as a HANDGUIDED OUTLINE QUILTED bedspread/coverlet.Seams will be pattern matched, serged & topstitched (stitch line is visible on face.)The lining & fill will be tack quilted together; the face fabric will be tacked (3 tacks) along the seams.Hem is serged and blindstitched. If cord or trim is used, there will be a facing on the back side when lining is used.If contrast lining, hem will be pillowcased 3 sides and topstitched along the top edge.Maximum amount of fill is 4 1/2 oz. Flannel interlining or bump cloth interlining may also be used.

SIZE MATTRESS DROP FINISHED SIZETwin 39" x 75" 21" 81" x 111" (includes 15" pillow tuck)Full 54" x 75" 21" 96" x 111" (includes 15" pillow tuck)Queen 60" x 80" 21" 102" x 121" (includes 20" pillow tuck)King 78" x 80" 21" 120" x 121" (includes 20" pillow tuck)

ALLOWANCES: WITHOUT FILLWidth:Width of top + 2 drops = FINISHED WIDTHFinished width + 8" work divided by fabric width = # cuts

Length:Length of top + 1 drop + pillow tuck = FINISHED LENGTHFinished length + 8" work = CUT LENGTHIf your fabric has a repeat, allowance must be made for matching pattern @ the seams.CUT LENGTH divided by REPEAT SIZE = # of repeats needed x REPEAT SIZE = ADJUSTED CUT LENGTH

YARDAGE ESTIMATE:ADJUSTED CUT LENGTH x # cuts needed divded by 36 = yardage estimate. (round up to nearest 1/4 yard)

STANDARD BEDSPREAD SIZES:


UNQUILTED BEDSPREADS

YC130, July 2010


Bedspread Yardage

Coverlet Yardage

Cording Yardage

Premade Trim Yardage (3 sides)

TWIN STANDARD THROW 7.00 6.5081" X 111" - 1/4" or 3/8" Cording at Hem 7.00 6.50 1.00(bedspread) - 1/2" or 1" Cording at Hem 7.00 6.50 2.00

(1) - 1" Shirred Cord at Hem 7.00 6.50 4.00- C.O.M. Trim at Hem 7.00 6.50 8.50FITTED - no cord or trim 7.00 6.50



FULL STANDARD THROW 7.00 6.50- 1/4" or 3/8" Cording at Hem 7.00 6.50 1.00


(1) - C.O.M. Trim at Hem 7.00 6.50 9.00FITTED - no cord or trim 7.00 6.50



QUEEN STANDARD THROW 11.00 7.00- 1/4" or 3/8" Cording at Hem 11.00 7.00 1.00





KING STANDARD THROW 11.00 10.50- 1/4" or 3/8" Cording at Hem 11.00 10.50 1.00





SUPER STANDARD THROW 12.00 12.00KING - 1/4" or 3/8" Cording at Hem 12.00 12.00 1.00

135" x 136" - 1/2" or 1" Cording at Hem 12.00 12.00 2.00(bedspread) - 1" Shirred Cord at Hem 12.00 12.00 4.00



(2) FITTED w/1/4" or 3/8" Cording at Mattress Edge & Hem 12.00 12.00 2.0054" SOLID FABRICS have been used for all fabric yardages. For repeats, multiply your repeat measurement by the number in the parenthesis, divide by 36, and add to the yardage listed.

Add the appropriate yardages for Cording or Trim to the styles below.

BEDDING PRODUCTSC.O.M YARDAGE REQUIREMENTS FOR UNQUILTED

BEDSPREADS

YC131, July 2010

Documents

YARDAGE CHARTSorders.andersonfabrics.com/LaborCatalogOrders/... · Hourglass Draperies 14 Single Layer Box pleat valance 29 Tapered Valances 66 ... CCESSORY CHARTS. ANDERSON FABRIC