ELECTRONICS A Division of Av-Comm
24/9 Powells Road, Brookvale, NSW 2100, Australia +61 2 9939 4377
[email protected]
[email protected]
ViaLiteHD_YELLOW_OEM_LINK_Datasheet_HRx-xx-xN-2.docx CR4415
30/03/20
Due to our policy of continuing product development, these
specifications are subject to change and improvement without
notice.
ViaLiteHD® – Yellow OEM Link
www.vialite.com +44(0)1793 784389
[email protected] +1 (855)
4-VIALITE
RF over Fiber OEM Module Single Tx or Rx 50 and 75 ohm versions
Board-mounted OEM Edge connector 65 x 40 x 15.6 mm* All ViaLiteHD
RF bands available
up to 4.2 GHz Support modules also available *Wideband OEM is
double canned; depth increases
The Yellow OEM Link is a small board-mounted RF over fiber OEM
module, available in all ViaLiteHD RF bands up to 4.2 GHz and can
be supplied in transmitter or receiver formats. It can be used
within the ViaLiteHD Satcom6, ODE-A4 and ODE-MINI outdoor
enclosures or easily mounted into customer equipment. The unit is
available with either an SC/APC, LC/APC, FC/APC or E2000/APC
optical connector, and either SMA or MCX RF connector. The OEM
module comes with a 15 pin edge connector which allows connections
for powering, Tx or Rx alarms, I2C setup for monitoring and
control, and serial data transmission such as RS232, RS485 &
TTL. By using the ViaLiteHD Programming Kit (HRx-HD-DEV103), the
module gain settings can be changed accordingly.
Mechanical Dimensions (mm)
YELLOW OEM LINK
ELECTRONICS A Division of Av-Comm
24/9 Powells Road, Brookvale, NSW 2100, Australia +61 2 9939 4377
[email protected]
Yellow OEM Link
1 8 3 6 7 98
T L N 3 S 1 3 1 0 10 11 12
Module Type R - Receiver(Optical in, RF out) T - Transmitter(RF in,
optical out)
H – ViaLiteHD
Electrical Connector 1 - SMA, 50Ω 5 - MCX, 50Ω 6 - MCX, 75Ω
Frequency B - IF 70/140MHz, 10-200MHz D - DVB-T broadcast,
470-860MHz G - GPS, special function 1GHz-1.8GHz L - L Band
700MHz-2450MHz N - General purpose 10MHz-1GHz S - Wideband 10MHz -
3GHz T - Low frequency timing, 10kHz - 50MHz U - Ultra Wideband
2kHz-4.2GHz W - Extra Wideband 10MHz - 4.2GHz
Optical Connector 6 - Singlemode FC/APC 7 - Singlemode E2000/APC 8
- Singlemode SC/APC 9 – Singlemode LC/APC
Module Package N – Yellow OEM Link
Options 0 - No LNA feed [TX or RX] 1 - +5V LNA feed option out of
RF input [TX only]* 2 - +12V LNA feed option out of RF input [TX
only]* 3 - LNA/LNB/BUC external feed to RF connector from rack/rear
panel [TX/RX]* 4 - 20kb/s RS485/422/232 channel, No LNA feed
[TX/RX]** 6 - GPS load simulator with +5V bias *** 9 - 20kb/s
RS485/422/232 channel, external LNA feed to RF connector [TX/RX]**
A - IRIG Low frequency extension (to ~100Hz), No LNA feed [TX/RX]
**** B - Voltage transient protection on output, small value series
capacitor [RX only]* C - 20kb/s TTL channel, No LNA feed
[TX/RX]**
*Current limits apply, see detailed information for each module **
Digital link only in direction of RF link *** ONLY available for
GPS modules **** ONLY available for Low frequency timing
modules
Nominal Gain(dB) TX RX 0 -5 +5 1 +5 NU 2 NU +11 3 -11 +20 4 NU NU 5
-15 +15 6 -25 +25 7 -35 +31 8 -11 +14 9 +0 +0
RX Photodiode Blank - Standard
TX B - DFB,CWDM dual isolated, 3mW ±3nm C - DFB, CWDM, 3mW ±3nm H -
DFB, Dual isolated, 3mW ±20nm S - DFB, standard, 3mW ±20nm W - DFB
with WDM, 3mW ±20nm
Laser Wavelength Wavelength (nm) Type 1270 B,C 1290 B,C 1310
B,C,H,K,P,S,W 1330 B,C 1350 B,C 1370 B,C 1390 B,C 1410 B,C 1430 B,C
1450 B,C 1470 B,C 1490 B,C 1510 B,C 1530 B,C 1550 B,C,H,K,P,S,W
1570 B,C 1590 B,C 1610 B,C
Popular products HRT-L1-8N-33-S1310 Yellow OEM L-Band HTS (700-2450
MHz) Transmitter with 50 ohm SMA and SC/APC connectors HRR-L1-8N-03
Yellow OEM L-Band HTS (700-2450 MHz) Receiver with 50 ohm SMA and
SC/APC connectors HRT-N6-8N-35-S1310 Yellow OEM VHF-UHF 10 MHz-1
GHz Transmitter with 75 ohm MCX and SC/APC connectors HRR-N6-8N-05
Yellow OEM VHF-UHF 10 MHz-1 GHz Receiver with 75 ohm MCX and SC/APC
connectors Specifications Yellow OEM Link
Dimensions Transmitter: 65 x 40 x 15.6 mm Receiver: 65 x 40 x 12.1
mm
Weight Transmitter: 60 g Receiver: 55 g
Operating temperature -10 °C to +60 °C
Humidity 0-95% non-condensing
Receiver: 1.3 W
DC Input voltage 11 to 13 V, 12 V nominal
Connector 15-pin edge connector
(Power, Serial Data, Alarms & I2C programming)
RF module Types Transmitter or Receiver
IF (B), DVB-T (D), GPS (G), L-Band HTS (L), General purpose (N),
Wideband (S), Low Frequency Timing Link (T), Ultra Wideband
(U&W), 1:1 Splitter, 1:1 Switch, Serial digital and
Ethernet.
ELECTRONICS A Division of Av-Comm
24/9 Powells Road, Brookvale, NSW 2100, Australia +61 2 9939 4377
[email protected]
[email protected]
ViaLiteHD_BLUE_OEM_LINK_Datasheet_HRx-xx-xM-3.docx CR4414
30/03/20
Due to our policy of continuing product development, these
specifications are subject to change and improvement without
notice.
ViaLiteHD® – Blue OEM Link
www.vialite.com +44(0)1793 784389
[email protected] +1 (855)
4-VIALITE
RF over Fiber OEM Module Single Tx or Rx External PSU Protective
enclosure 50 and 75 ohm versions 89 x 46 x 20 mm Available in all
bands up to 4.2 GHz Supports 0-10 km and 50 km DIN Rail mount
option
The Blue OEM Link is a small compact RF over fiber module which is
available in all ViaLiteHD RF bands up to 4.2 GHz, in either
transmitter or receiver formats. The link is available with SC/APC
or FC/APC optical connectors and either SMA or MCX RF connectors.
The module can be used as an OEM unit, which can be easily mounted
into customer equipment, or as a standalone product for temporary
or permanent installation (with the use of the HPS-CS-3 external
power supply if needed). The unit comes with a 15 pin Molex single
row connector which allows connections for powering, Tx or Rx
alarms, I2C setup for monitoring and control and serial data
transmission such as RS232, RS485 & TTL. By using the ViaLiteHD
Programming Kit (HRx-HD-DEV103) module gain settings can be changed
accordingly. Mechanical dimensions (mm)
BLUE OEM LINK
ELECTRONICS A Division of Av-Comm
24/9 Powells Road, Brookvale, NSW 2100, Australia +61 2 9939 4377
[email protected]
Blue OEM Link
1 8 3 6 7 98
T L M 3 S 1 3 1 0 10 11 12
Module Type R - Receiver(Optical in, RF out) T - Transmitter(RF in,
optical out)
H – ViaLiteHD
Electrical Connector 1 - SMA, 50Ω 5 - MCX, 50Ω 6 - MCX, 75Ω
Frequency B - IF 70/140MHz, 10-200MHz D - DVB-T broadcast,
470-860MHz G - GPS, special function 1GHz-1.8GHz L - L Band HTS
700MHz-2450MHz N - General purpose 10MHz-1GHz S - Wideband 10MHz -
3GHz T - Low frequency timing, 10kHz - 50MHz U - Ultra Wideband
2kHz-4.2GHz W - Extra Wideband 10MHz - 4.2GHz
Optical Connector 6 - Singlemode FC/APC 8 - Singlemode SC/APC
Module Package M – Blue Link
Options 0 - No LNA feed [TX or RX] 1 - +5V LNA feed option out of
RF input [TX only]* 2 - +12V LNA feed option out of RF input [TX
only]* 3 - LNA/LNB/BUC external feed to RF connector from rack/rear
panel [TX/RX]* 4 - 20kb/s RS485/422/232 channel, No LNA feed
[TX/RX]** 6 - GPS load simulator with +5V bias *** 9 - 20kb/s
RS485/422/232 channel, external LNA feed to RF connector [TX/RX]**
A - IRIG Low frequency extension (to ~100Hz), No LNA feed [TX/RX]
**** B - Voltage transient protection on output, small value series
capacitor [RX only]* C - 20kb/s TTL channel, No LNA feed
[TX/RX]**
*Current limits apply, see detailed information for each module **
Digital link only in direction of RF link *** ONLY available for
GPS modules **** ONLY available for Low frequency timing
modules
Nominal Gain(dB) TX RX 0 -5 +5 1 +5 NU 2 NU +11 3 -11 +20 4 NU NU 5
-15 +15 6 -25 +25 7 -35 +31 8 -11 +14 9 +0 +0
RX Photodiode Blank - Standard
TX B - DFB,CWDM dual isolated, 3mW ±3nm C - DFB, CWDM, 3mW ±3nm H -
DFB, Dual isolated, 3mW ±20nm S - DFB, standard, 3mW ±20nm
Laser Wavelength Wavelength (nm) Type 1270 B,C 1290 B,C 1310
B,C,H,K,P,S,W 1330 B,C 1350 B,C 1370 B,C 1390 B,C 1410 B,C 1430 B,C
1450 B,C 1470 B,C 1490 B,C 1510 B,C 1530 B,C 1550 B,C,H,K,P,S,W
1570 B,C 1590 B,C 1610 B,C
Popular products HRT-L1-8M-33-S1310 Blue OEM Link L-Band (700-2450
MHz) transmitter with 50 ohm SMA and SC/APC connectors HRR-L1-8M-03
Blue OEM Link L-Band (700-2450 MHz) receiver with 50 ohm SMA and
SC/APC connectors HRT-G1-8M-10-S1310 Blue OEM Link GPS transmitter
with 50 ohm SMA and SC/APC connectors HRR-G1-8M-60 Blue OEM Link
GPS receiver with 50 ohm SMA and SC/APC connectors
Specifications
Blue OEM Link
Dimensions With mounting bracket fitted: 89 x 60 x 21 mm Without
mounting bracket fitted: 89 x 46 x 20 mm
Weight With mounting bracket fitted: 130 g typical Without mounting
bracket fitted: 112 g typical
Operating temperature -10 °C to +60 °C Humidity 0-95%
non-condensing Cooling Convection Power consumption Transmitter:
1.9 W
Receiver: 1.3 W DC Input voltage 11 to 13 V, 12 V nominal Connector
15 pin header (male) Molex (C-Grid III), single row
(Power, Serial Data, Alarms & I2C programming) Power supply
compatibility HPS-CS-3 RF module types Transmitter or
Receiver
IF (B), DVB-T (D), GPS (G), L-Band HTS (L), General purpose (N),
Wideband (S), Low Frequency Timing Link (T), Ultra Wideband
(U&W)
DIN Rail Mounting Kit for Blue OEM (P/N 27500) A DIN rail is a
metal rail of an IEC/EN standard type widely used for mounting
electrical equipment inside equipment racks. The DIN Rail Mounting
Kit allows the ViaLiteHD Blue OEM to be mounted vertically and more
efficiently. This approach allows custom integration into any
enclosure or equipment room which has rails fitted.
ELECTRONICS A Division of Av-Comm
24/9 Powells Road, Brookvale, NSW 2100, Australia +61 2 9939 4377
[email protected]
[email protected]
ViaLiteHD_L_Band_CWDM_75_Ohm_Datasheet_HRx-L1_DS_5.docx CR4505
29/07/2020
Due to our policy of continuing product development, these
specifications are subject to change and improvement without
notice.
ViaLiteHD® – L-Band HTS RF over Fiber Links
www.vialite.com +44 (0)1793 784389
[email protected] +1 (855)
4-VIALITE
75 Ohm CWDM L-Band HTS Up to 50 km L-Band HTS (700-2450MHz) Up to
16 channels in a single fiber 65 dB dynamic range for 500 MHz
traffic 13/18V and 22 KHz tone LNB option Blind mate option
Standard 5-year warranty
ViaLiteHD L-Band HTS CWDM fiber optic links use coarse wavelength
division (CWDM) multiplexer lasers and have been designed for the
broadcast satellite industry to transport RF signals between
antennas and control rooms, where reducing fiber count is key. Due
to the very wide dynamic range, the same link can be used in both
the transmit and receive paths, over the same fiber. This dynamic
range allows High Throughput Satellite (HTS) transponder bandwidths
of 500, 800 or even 1500 MHz to be transported, as well as multiple
standard 36MHz transponders. The chassis cards are available with
the ViaLiteHD blind mate option, which allows all cables to be
connected at the rear of the chassis when installed. It also allows
configuration changes to be completed without disturbing the
connections and very fast changeover of cards; enabling five 9s
reliability. Options include: • 75 electrical connectors: BNC,
F-Type and MCX • Optical connectors: SC/APC, LC/APC, FC/APC and
E2000/APC • Test ports on Tx and Rx modules • Built-in BiasT for
LNB powering through RF connection • LNB control circuit with 13/18
VDC and 22 kHz tone • Blind mate connectivity (SC/APC and BNC) •
Serial digital channel to 20 kb/s on same optical path
Applications
Fiber count reduction Broadcast facilities Mobile SNG, military and
flyaways Television Receive-Only (TVRO) Fixed satcom earth stations
and teleports VSAT hubs (IP gateways) Marine antennas Telemetry,
Tracking and Command (TT&C) Oil and gas platforms
Formats 3U Chassis 1U Chassis Blue OEM Yellow OEM Outdoor
enclosures Related Products 50km L-Band HTS 50 Ohm CWDM L-Band HTS
HTS 100 km+ systems DWDM links
L-BAND HTS RF OVER FIBER LINKS
ELECTRONICS A Division of Av-Comm
24/9 Powells Road, Brookvale, NSW 2100, Australia +61 2 9939 4377
[email protected]
75 Ohm CWDM L-Band HTS
HH RR 1 2 3 4 5
33 88 33 6 7 98
UU LL DD 88 CC 15901590 16101610 10 11 12
Module Type R - Receiver(Optical in, RF out) V - Dual
Receiver(Optical in, RF out) T - Transmitter(RF in, optical out) U
- Dual Transmitter(RF In, optical out) X - Transceiver(Optical
in/out, RF out/in)
Module Type R - Receiver(Optical in, RF out) V - Dual
Receiver(Optical in, RF out) T - Transmitter(RF in, optical out) U
- Dual Transmitter(RF In, optical out) X - Transceiver(Optical
in/out, RF out/in)
H – ViaLiteHDH – ViaLiteHD
Electrical Connector 2 - F Type, 75Ω 3 - BNC, 75Ω 6 - MCX,
75Ω
Electrical Connector 2 - F Type, 75Ω 3 - BNC, 75Ω 6 - MCX,
75Ω
Frequency L - L Band HTS 700MHz-2450MHz Frequency L - L Band HTS
700MHz-2450MHz
Optical Connector 0 - No optical connector 1 - Multimode ST/PC* 2 -
Singlemode LC/PC* 3 - NU 4 - Singlemode FC/PC* 5 - Singlemode Lemo
2K* 6 - Singlemode FC/APC 7 - Singlemode E2000/APC 8 - Singlemode
SC/APC 9 - Singlemode LC/APC A - Singlemode SC/PC* B - Singlemode
ST/PC*
*Requires double isolated B” or H” laser
Optical Connector 0 - No optical connector 1 - Multimode ST/PC* 2 -
Singlemode LC/PC* 3 - NU 4 - Singlemode FC/PC* 5 - Singlemode Lemo
2K* 6 - Singlemode FC/APC 7 - Singlemode E2000/APC 8 - Singlemode
SC/APC 9 - Singlemode LC/APC A - Singlemode SC/PC* B - Singlemode
ST/PC*
*Requires double isolated B” or H” laser
Module Package D –Chassis Blind mate* R - Chassis Plug in M – Blue
OEM Link N – Yellow OEM Link** P- BLUE2 Link
*Blind mate modules only available with: RF: 75Ω BNC Optical:
SC/APC only
**For use in Satcom6
Module Package D –Chassis Blind mate* R - Chassis Plug in M – Blue
OEM Link N – Yellow OEM Link** P- BLUE2 Link
*Blind mate modules only available with: RF: 75Ω BNC Optical:
SC/APC only
**For use in Satcom6
Options 0 - No LNA feed [TX or RX] 1 - +5V LNA feed option out of
RF input [TX only]* 2 - +12V LNA feed option out of RF input [TX
only]* 3 - LNA/LNB/BUC external feed to RF connector from rack/rear
panel [TX/RX]* 4 - 20kb/s RS485/422/232 channel, No LNA feed
[TX/RX]** 5 - LNB control 13v/18v/22kHz tone [TX only]* 9 - 20kb/s
RS485/422/232 channel, external LNA feed to RF connector [TX/RX]**
B - Voltage transient protection on output, small value series
capacitor [RX only]* C - 20kb/s TTL channel, No LNA feed
[TX/RX]**
*Current limits apply, see detailed information for each module **
Digital link only in direction of RF link
Options 0 - No LNA feed [TX or RX] 1 - +5V LNA feed option out of
RF input [TX only]* 2 - +12V LNA feed option out of RF input [TX
only]* 3 - LNA/LNB/BUC external feed to RF connector from rack/rear
panel [TX/RX]* 4 - 20kb/s RS485/422/232 channel, No LNA feed
[TX/RX]** 5 - LNB control 13v/18v/22kHz tone [TX only]* 9 - 20kb/s
RS485/422/232 channel, external LNA feed to RF connector [TX/RX]**
B - Voltage transient protection on output, small value series
capacitor [RX only]* C - 20kb/s TTL channel, No LNA feed
[TX/RX]**
*Current limits apply, see detailed information for each module **
Digital link only in direction of RF link
Nominal Gain(dB) TX RX 0 -5 +5 2 NU +11 3 -11 +20 5 -15 +15 8 -11
+14
Nominal Gain(dB) TX RX 0 -5 +5 2 NU +11 3 -11 +20 5 -15 +15 8 -11
+14
TX/TRX/DTX Laser B - DFB,CWDM dual isolated, 3mW ±3nm C - DFB,
CWDM, 3mW ±3nm
TX/TRX/DTX Laser B - DFB,CWDM dual isolated, 3mW ±3nm C - DFB,
CWDM, 3mW ±3nm
Laser Wavelength Wavelength (nm) Type
1270 B,C 1290 B,C 1310 B,C 1330 B,C 1350 B,C 1370 B,C 1390 B,C 1410
B,C 1430 B,C 1450 B,C 1470 B,C 1490 B,C 1510 B,C 1530 B,C 1550 B,C
1570 B,C 1590 B,C 1610 B,C
Laser Wavelength Wavelength (nm) Type
1270 B,C 1290 B,C 1310 B,C 1330 B,C 1350 B,C 1370 B,C 1390 B,C 1410
B,C 1430 B,C 1450 B,C 1470 B,C 1490 B,C 1510 B,C 1530 B,C 1550 B,C
1570 B,C 1590 B,C 1610 B,C
Product Configurator Popular products HRT-L3-6R-58-C1610 L-Band
700-2450 MHz, 75 Ohm BNC, Singlemode SC/APC, Rack plug-in module,
Wavelength 1610 nm HRR-L3-8R-08 L-Band 700-2450 MHz, 75 Ohm BNC,
Singlemode SC/APC, Rack plug-in module RF parameters for popular
link gains
Link Tx Gain Rx Gain
Link Noise Figure (Default Tx Gain)
Link Noise Figure (Max Tx Gain)
Link P1dB (Default Tx Gain)
Link P1dB (Max Tx Gain)
HRT-L1-xx-x8-C1610 & HRR-L1-xx-x8 (3dB Gain Link)
-11 dB +14 dB 21 dB 13.5 dB 0 dBm -7.5 dBm
HRT-L1-xx-x5-C1610 & HRR-L1-xx-x5
(Unity Gain Link)
-15 dB +15 dB 25 dB 13.5 dB +2 dBm -8.5 dBm
HRT-L1-xx-x8-C1610 & HRR-L1-xx-x2
(Low Noise Unity Gain Link)
-11 dB +11 dB 21 dB 13.5 dB 0 dBm -7.5 dBm
Nominal Gain(dB) TX RX 0 -5 +5 2 NU +11 5 -15 +15 6 -25 +25
Nominal Gain(dB) TX RX 0 -5 +5 2 NU +11 5 -15 +15 6 -25 +25
ELECTRONICS A Division of Av-Comm
24/9 Powells Road, Brookvale, NSW 2100, Australia +61 2 9939 4377
[email protected]
75 Ohm CWDM L-Band HTS
Technical specification
Units L-Band HTS 75 ohms Transmitter HRT-L3-8D-38-C1610 (example)
Receiver HRR-L3-8D-08 (example) Frequency range MHz 700-2450
Impedance, RF connector 75Ω BNC, blind mate VSWR (typ) 1:1.5 Link
gain (Tx gain / Rx gain), default dB (nom) a +3 (-11 /+14) Tx gain
adjustment range dB (typ) 15.5 Tx gain adjustment from default gain
dB (typ) -7.5 to +8.0 Rx gain adjustment range dB (typ) 15.5 Rx
gain adjustment from default gain dB (typ) -7.5 to +8.0 Gain
adjustment step size Rx and Tx dB (typ) 0.5 Flatness, fullband dB
(max) a h ±1.4 Flatness, fullband dB (typ) a h ±0.6 Flatness, 36MHz
dB (typ) a ±0.2 Gain stability over temperature range dB (max) a ±3
Gain stability dB (typ) 0.25 @ 24 hrs Nominal input signal / output
signal dBm -20 / -20 IMD @ nominal output power dB (typ) c -50 CNR
@ nominal input power, 36MHz dB (typ) b 56 P1dBinput dBm (typ) a k
0 P1dBinput, at minimum Tx gain dBm (typ) a k 5 IP3input, at
default gain dBm (typ) a k 12 Noise figure, at default gain dB
(typ) a k 21 Noise figure, at maximum Tx gain dB (typ) a k 18 Noise
figure, 5dB optical loss dB (typ) c k 27 SFDR dB/Hz (typ) a 110
Test port gain, transmitter dB (typ) l -26 Test port gain, receiver
dB (typ) l -14 Test port flatness dB (typ) l ±1 Maximum input power
without damage dBm (min) 15 LNB power External 0-28V @ 350mA from
chassis power connector Power configuration Tx W (typ) 1.9 Power
configuration Rx W (typ) 1.3 Optical connector SC/APC, blind mate
Optical wavelength nm 1270-1610 ± 3 Laser type DFB (Distributed
feedback) laser Optical power output dBm (typ) 4.5 Summary alarm
output Open drain alarm: OPEN: Alarm, CURRENT SINK: okay Operating
temperature range e -20 °C to +60 °C Storage temperature range
-40°C to +70°C Humidity RH 95% non-condensing humidity
a Nominal input power @ 0dB optical loss
b Nominal input power @ 1dB optical loss c Nominal output power @
5dB optical loss h Default gain setting k Measured @ 1.2GHz l
Relative to rear port @1.2GHz All tests @ 25°C after 15 minutes
warm up
e Datasheet parameters based on temperature range -10°C to +50°C,
refer to user manual for performance parameters @ -20 °C and +60
°C
ELECTRONICS A Division of Av-Comm
24/9 Powells Road, Brookvale, NSW 2100, Australia +61 2 9939 4377
[email protected]
75 Ohm CWDM L-Band HTS
Accessories Type Key Features SNMP/Web Browser Card
Easy to use graphical user interface (GUI) Real time monitoring of
card performance Alarm monitoring and event logging Control of gain
adjustment Compatible with all ViaLiteHD rack chassis and modules
Easy integration with network management systems (NMS)
using management information base (MIB) tables Actively manage
redundancy switching New RF cards can be automatically reprogrammed
with the
previous card parameters Remote SNMP to local SNMP connection via
optical fiber Provides remote LAN 10/100 Ethernet link
Dual Redundancy
1:1 redundancy for L-Band Maximises link up-time Can be used to
backup copper coax Manual and automatic control via SNMP Flexible
configuration options Other redundancy options available
Rack Chassis
3U accepts up to 13 RF or Support cards, plus an SNMP card and dual
power supplies
A 1U chassis accepts up to 3 RF or Support cards or 2 cards and an
SNMP card (with dual power supplies)
Up to 26 channels per 3U chassis (using dual RF cards) – reducing
the amount of rack space required
Blind mate option All modules hot-swappable and auto
reconfiguration with
SNMP option On-card LNB and BUC power options Power fed through
rear chassis connector to card Bias Tees System can be monitored
and controlled remotely via SNMP
using a web browser
Outdoor Enclosures
CE approved and EMC compatible IP rated and NEMA approved Plug and
play format Suitable for harsh environments All modules hot
swappable Dual redundant power options Interface for monitor and
control (M&C) systems
ELECTRONICS A Division of Av-Comm
24/9 Powells Road, Brookvale, NSW 2100, Australia +61 2 9939 4377
[email protected]
[email protected]
ViaLiteHD_L_Band_CWDM_50_Ohm_Datasheet_HRx-L1_DS_5.docx CR4505
29/07/2020
Due to our policy of continuing product development, these
specifications are subject to change and improvement without
notice.
ViaLiteHD® – L-Band HTS RF over Fiber Link
www.vialite.com +44 (0)1793 784389
[email protected] +1 (855)
4-VIALITE
50 Ohm CWDM L-Band HTS Up to 50 km L-Band HTS (700-2450 MHz) Up to
16 channels in a single fiber 65 dB dynamic range for 500 MHz
traffic 13/18 V and 22 KHz tone LNB option Blind mate option
Standard 5-year warranty
ViaLiteHD L-Band HTS CWDM fiber optic links use coarse wavelength
division multiplexer (CWDM) lasers and have been designed for the
satellite industry to transport RF signals between antennas and
control rooms, where reducing fiber count is key. Due to the very
wide dynamic range, the same link can be used in both the transmit
and receive paths, over the same fiber. This dynamic range allows
High Throughput Satellite (HTS) transponder bandwidths of 500, 800
or even 1500 MHz to be transported, as well as multiple standard 36
MHz transponders. The chassis cards are available with the
ViaLiteHD blind mate option, which allows all cables to be
connected at the rear of the chassis when installed. It also allows
any configuration changes to be completed without disturbing the
connections and very fast changeover of cards; enabling five 9s
reliability. Options include: • 50 electrical connectors: SMA and
MCX • Optical connectors: SC/APC, LC/APC, FC/APC and E2000/APC •
Test ports on Tx and Rx modules • Built-in BiasT for LNB powering
through RF connection • LNB control circuit with 13/18 VDC and 22
kHz tone • Blind mate connectivity (SC/APC and SMA) • Serial
digital channel to 20 kb/s on same optical path
Applications
Fiber count reduction Fixed satcom earth stations and teleports
Broadcast facilities Mobile SNG, military and flyaways VSAT hubs
(IP gateways) Marine antennas Telemetry, Tracking and Command
(TT&C) Oil and gas platforms Television Receive-Only
(TVRO)
Formats 3U Chassis 1U Chassis Blue OEM Yellow OEM Outdoor
enclosures Related Products 50 km L-Band HTS 75 Ohm CWDM L-Band HTS
HTS 100 km+ systems DWDM links
L-BAND HTS RF OVER FIBER LINKS
ELECTRONICS A Division of Av-Comm
24/9 Powells Road, Brookvale, NSW 2100, Australia +61 2 9939 4377
[email protected]
50 Ohm CWDM L-Band HTS
Product Configurator
11 88 55 6 7 98
UU LL DD 33 CC 1 5 9 01 5 9 0 1 6 1 0 1 6 1 0 10 11 12
Module Type R - Receiver(Optical in, RF out) V - Dual
Receiver(Optical in, RF out) T - Transmitter(RF in, optical out) U
- Dual Transmitter(RF In, optical out) X - Transceiver(Optical
in/out, RF out/in)
Module Type R - Receiver(Optical in, RF out) V - Dual
Receiver(Optical in, RF out) T - Transmitter(RF in, optical out) U
- Dual Transmitter(RF In, optical out) X - Transceiver(Optical
in/out, RF out/in)
H – ViaLiteHDH – ViaLiteHD
Electrical Connector 1 - SMA, 50Ω 5 - MCX, 50Ω
Electrical Connector 1 - SMA, 50Ω 5 - MCX, 50Ω
Frequency L - L Band HTS 700MHz-2450MHz Frequency L - L Band HTS
700MHz-2450MHz
Optical Connector 0 - No optical connector 1 - Multimode ST/PC* 2 -
Singlemode LC/PC* 3 - NU 4 - Singlemode FC/PC* 5 - Singlemode Lemo
2K* 6 - Singlemode FC/APC 7 - Singlemode E2000/APC 8 - Singlemode
SC/APC 9 - Singlemode LC/APC A - Singlemode SC/PC* B - Singlemode
ST/PC*
*Requires double isolated B or H laser
Optical Connector 0 - No optical connector 1 - Multimode ST/PC* 2 -
Singlemode LC/PC* 3 - NU 4 - Singlemode FC/PC* 5 - Singlemode Lemo
2K* 6 - Singlemode FC/APC 7 - Singlemode E2000/APC 8 - Singlemode
SC/APC 9 - Singlemode LC/APC A - Singlemode SC/PC* B - Singlemode
ST/PC*
*Requires double isolated B or H laser
Module Package D - Chassis Blind mate* R – Chassis Plug In M – Blue
OEM Link N – Yellow OEM Link** P – BLUE2 Link
*Blindmate modules only available with: RF: 50Ω SMA or 75Ω BNC
Optical: SC/APC only
**For use in Satcom6
Module Package D - Chassis Blind mate* R – Chassis Plug In M – Blue
OEM Link N – Yellow OEM Link** P – BLUE2 Link
*Blindmate modules only available with: RF: 50Ω SMA or 75Ω BNC
Optical: SC/APC only
**For use in Satcom6
Options 0 - No LNA feed [TX or RX] 1 - +5V LNA feed option out of
RF input [TX only]* 2 - +12V LNA feed option out of RF input [TX
only]* 3 - LNA/LNB/BUC external feed to RF connector from rack/rear
panel [TX/RX]* 4 - 20kb/s RS485/422/232 channel, No LNA feed
[TX/RX]** 5 - LNB control 13v/18v/22kHz tone [TX only]* 9 - 20kb/s
RS485/422/232 channel, external LNA feed to RF connector [TX/RX]**
B - Voltage transient protection on output, small value series
capacitor [RX only]* C - 20kb/s TTL channel, No LNA feed
[TX/RX]**
*Current limits apply, see detailed information for each module **
Digital link only in direction of RF link
Options 0 - No LNA feed [TX or RX] 1 - +5V LNA feed option out of
RF input [TX only]* 2 - +12V LNA feed option out of RF input [TX
only]* 3 - LNA/LNB/BUC external feed to RF connector from rack/rear
panel [TX/RX]* 4 - 20kb/s RS485/422/232 channel, No LNA feed
[TX/RX]** 5 - LNB control 13v/18v/22kHz tone [TX only]* 9 - 20kb/s
RS485/422/232 channel, external LNA feed to RF connector [TX/RX]**
B - Voltage transient protection on output, small value series
capacitor [RX only]* C - 20kb/s TTL channel, No LNA feed
[TX/RX]**
*Current limits apply, see detailed information for each module **
Digital link only in direction of RF link
Nominal Gain(dB) TX RX 0 -5 +5 2 NU +11 3 -11 +20 5 -15 +15 6 -25
+25
Nominal Gain(dB) TX RX 0 -5 +5 2 NU +11 3 -11 +20 5 -15 +15 6 -25
+25
TX/TRX/DTX Laser
B - DFB,CWDM dual isolated, 3mW ±3nm C - DFB, CWDM, 3mW ±3nm
TX/TRX/DTX Laser
B - DFB,CWDM dual isolated, 3mW ±3nm C - DFB, CWDM, 3mW ±3nm
Laser Wavelength Wavelength (nm) Type
1270 B,C 1290 B,C 1310 B,C 1330 B,C 1350 B,C 1370 B,C 1390 B,C 1410
B,C 1430 B,C 1450 B,C 1470 B,C 1490 B,C 1510 B,C 1530 B,C 1550 B,C
1570 B,C 1590 B,C 1610 B,C
Laser Wavelength Wavelength (nm) Type
1270 B,C 1290 B,C 1310 B,C 1330 B,C 1350 B,C 1370 B,C 1390 B,C 1410
B,C 1430 B,C 1450 B,C 1470 B,C 1490 B,C 1510 B,C 1530 B,C 1550 B,C
1570 B,C 1590 B,C 1610 B,C
Popular products HRT-L1-8R-33-C1610 L-Band 700-2450 MHz, 50 Ohm
SMA, Singlemode SC/APC, Rack plug-in module, Wavelength 1610 nm
HRR-L1-8R-03 L-Band 700-2450 MHz, 50 Ohm SMA, Singlemode SC/APC,
Rack plug-in module RF parameters for popular link gains
Link Tx Gain Rx Gain
Link Noise Figure (Default Tx Gain)
Link Noise Figure (Max Tx Gain)
Link P1 dB (Default Tx Gain)
Link P1 dB (Max Tx Gain)
HRT-L1-xx-x3-C1610 & HRR-L1-xx-x3
(9dB Gain Link)
-11 dB +20 dB 20 dB 12.5 dB -1 dBm -8.5 dBm
HRT-L1-xx-x5-C1510 & HRR-L1-xx-x5
(Unity Gain Link)
-15 dB +15 dB 24 dB 12.5 dB +3 dBm -8.5 dBm
HRT-L1-xx-x6-C1530 & HRR-L1-xx-x6 (High P1dB Unity Gain
Link)
-25 dB +25 dB 34 dB 29 dB +13 dBm +9 dBm
ELECTRONICS A Division of Av-Comm
24/9 Powells Road, Brookvale, NSW 2100, Australia +61 2 9939 4377
[email protected]
50 Ohm CWDM L-Band HTS
Technical specification
Units Note L-Band HTS 50 ohms Transmitter (Tx) HRT-L1-8R-33-S1310
(example) Receiver (Rx) HRR-L1-8R-03 (example) Frequency range MHz
700-2450 Impedance, RF connector 50 Ω SMA, blind mate VSWR (typ)
1:1.5 Transmitter (Tx) gain, default dB (typ) a -11 +/- 0.5
Receiver (Rx) gain, default dB (typ) a +20 +/- 0.5 Link gain (Tx
& Rx), default dB (typ) a +9 +/- 1.5 Tx gain adjustment range
dB (typ) 15.5 Tx gain adjustment from default gain dB (min) d +/- 3
Rx gain adjustment range dB (typ) 15.5 Rx gain adjustment from
default gain dB (min) d +/- 3 Gain adjustment step size Rx and Tx
dB (typ) 0.5 Flatness, fullband dB (max) a h ±1.2 Flatness,
fullband dB (typ) a h ±0.5 Flatness, 36 MHz dB (typ) a ±0.2 Gain
stability over temperature range dB (max) a ±3 Gain stability dB
(typ) 0.25 @ 24 hrs Nominal input signal / output signal dBm -20 /
-20 IMD @ nominal output power dB (typ) c -61 CNR @ nominal input
power, 36 MHz dB (typ) b 57 P1dBinput dBm (typ) a k -1 P1dBinput,
at minimum Tx gain dBm (typ) a k 0.5 IP3input, at default gain dBm
(typ) a k 11 Noise figure, at default gain dB (typ) a k 20 Noise
figure, at maximum Tx gain dB (typ) a k 13 Noise figure, 5 dB
optical loss dB (typ) c k 26 SFDR dB/Hz (typ) a 110 Test port gain,
transmitter dB (typ) l -20 Test port gain, receiver dB (typ) l -20
Test port flatness dB (typ) l ±1 Maximum input power without damage
dBm (min) 15 LNB power External 0-28 V @ 350 mA from chassis power
connector Power consumption Tx W (typ) 1.9 Power consumption Rx W
(typ) 1.3 Optical connector SC/APC, blind mate Optical wavelength
nm 1310 ± 20 Laser type DFB (Distributed feedback) laser Optical
power output dBm (typ) 4.5 Summary alarm output Open drain alarm:
OPEN: Alarm, CURRENT SINK: okay Operating temperature range e -20
°C to +60 °C Storage temperature range -40 °C to +70 °C Humidity RH
95% non-condensing humidity a Nominal input power @ 0 dB optical
loss
b Nominal input power @ 1 dB optical loss c Nominal output power @
5 dB optical loss
h Default gain setting k Measured @ 1.2 GHz
l Relative to rear port @1.2 GHz
All tests @ 25 °C after 15 minutes warm up
d Guaranteed minimum adjustment from default gain
e Datasheet parameters based on temperature range -10°C to
+50°C,
refer to user manual for performance parameters @ -20 °C and +60
°C
ELECTRONICS A Division of Av-Comm
24/9 Powells Road, Brookvale, NSW 2100, Australia +61 2 9939 4377
[email protected]
50 Ohm CWDM L-Band HTS
Accessories Type Key Features SNMP/Web Browser card
Easy to use graphical user interface (GUI) Real time monitoring of
card performance Alarm monitoring and event logging Control of gain
adjustment Compatible with all ViaLiteHD rack chassis and modules
Easy integration with network management systems (NMS)
using management information base (MIB) tables Actively manage
redundancy switching New RF cards can be automatically reprogrammed
with the
previous card parameters Remote SNMP to local SNMP connection via
optical fiber Provides remote LAN 10/100 Ethernet link
Dual Redundancy
1:1 redundancy for L-Band Maximises link up-time Can be used to
backup copper coax Manual and automatic control via SNMP Flexible
configuration options Other options available
Rack Chassis
3U accepts up to 13 RF or Support cards, plus an SNMP card and dual
power supplies
A 1U chassis accepts up to 3 RF or Support cards or 2 cards and an
SNMP card (with dual power supplies)
Up to 26 channels per 3U chassis (using dual RF cards) – reducing
the amount of rack space required
Blind mate option All modules hot-swappable and
auto-reconfiguration with
SNMP option On-card LNB and BUC power options Power fed through
rear chassis connector to card Bias Tees System can be monitored
and controlled remotely via SNMP
using a web browser
Outdoor Enclosures
CE approved and EMC compatible IP rated and NEMA approved Plug and
play format Suitable for harsh environments All modules hot
swappable Dual redundant power options Interface for monitor and
control (M&C) systems
ELECTRONICS A Division of Av-Comm
24/9 Powells Road, Brookvale, NSW 2100, Australia +61 2 9939 4377
[email protected]
[email protected]
ViaLiteHD_L_Band_75_Ohm_50km_Datasheet_HRx-L1_DS_5.docx CR4505
29/07/2020
Due to our policy of continuing product development, these
specifications are subject to change and improvement without
notice.
ViaLiteHD® – L-Band HTS RF over Fiber Links
www.vialite.com +44 (0)1793 784389
[email protected] +1 (855)
4-VIALITE
75 Ohm L-Band HTS 50 km 10-50 km link 65 dB dynamic range for 500
MHz traffic L-Band HTS (700-2450 MHz) 13/18 V and 22 KHz tone LNB
option Blind mate option Standard 5-year warranty
ViaLiteHD L-Band HTS 50 km fiber optic links use 1550 nm lasers and
have been designed for the broadcast satellite industry to
transport RF signals between antennas and control rooms over fiber.
Due to the very wide dynamic range, the same link can be used in
both the transmit and receive paths. This dynamic range allows High
Throughput Satellite (HTS) transponder bandwidths of 500, 800 or
even 1500 MHz to be transported, as well as multiple standard 36
MHz transponders. The chassis cards are available with the
ViaLiteHD blind mate option which allows all cables to be connected
at the rear of the chassis when installed. It also allows any
configuration changes to be completed without disturbing the
connections and very fast changeover of cards; enabling five 9s
reliability. Options include: • 75 electrical connectors: BNC,
F-Type and MCX • Optical connectors: SC/APC, LC/APC, FC/APC and
E2000/APC • Test ports on Tx and Rx modules • Built-in BiasT for
LNB powering through RF connection • LNB control circuit with 13/18
VDC and 22 kHz tone • Blind mate connectivity (SC/APC and BNC) •
Serial digital channel to 20 kb/s on same optical path
Applications
Broadcast facilities Mobile SNG, military and flyaways Television
Receive-Only (TVRO) Fixed satcom earth stations and teleports VSAT
hubs (IP gateways) Marine antennas Telemetry, Tracking and Command
(TT&C) Oil and gas platforms
Formats 3U Chassis 1U Chassis Blue OEM and Blue2 Link Yellow OEM
Outdoor enclosures Related Products 0-10 km 1310 nm L-Band HTS 50
Ohm L-Band HTS HTS 100 km+ systems DWDM links
L-BAND HTS RF OVER FIBER LINKS
ELECTRONICS A Division of Av-Comm
24/9 Powells Road, Brookvale, NSW 2100, Australia +61 2 9939 4377
[email protected]
75 Ohm L-Band HTS 50km
Product configurator
33 88 33 6 7 98
UU LL DD 88 SS 13101310 13101310 10 11 12
Module Type R - Receiver(Optical in, RF out) V - Dual
Receiver(Optical in, RF out) T - Transmitter(RF in, optical out) U
- Dual Transmitter(RF In, optical out) X - Transceiver(Optical
in/out, RF out/in)
Module Type R - Receiver(Optical in, RF out) V - Dual
Receiver(Optical in, RF out) T - Transmitter(RF in, optical out) U
- Dual Transmitter(RF In, optical out) X - Transceiver(Optical
in/out, RF out/in)
H – ViaLiteHDH – ViaLiteHD
Electrical Connector 2 - F Type, 75Ω 3 - BNC, 75Ω 6 - MCX,
75Ω
Electrical Connector 2 - F Type, 75Ω 3 - BNC, 75Ω 6 - MCX,
75Ω
Frequency L - L Band HTS 700MHz-2450MHz Frequency L - L Band HTS
700MHz-2450MHz
Optical Connector 0 - No optical connector 1 - Multimode ST/PC* 2 -
Singlemode LC/PC* 3 - NU 4 - Singlemode FC/PC* 5 - Singlemode Lemo
2K* 6 - Singlemode FC/APC 7 - Singlemode E2000/APC 8 - Singlemode
SC/APC 9 - Singlemode LC/APC A - Singlemode SC/PC* B - Singlemode
ST/PC*
*Requires double isolated “B” or “H” laser
Optical Connector 0 - No optical connector 1 - Multimode ST/PC* 2 -
Singlemode LC/PC* 3 - NU 4 - Singlemode FC/PC* 5 - Singlemode Lemo
2K* 6 - Singlemode FC/APC 7 - Singlemode E2000/APC 8 - Singlemode
SC/APC 9 - Singlemode LC/APC A - Singlemode SC/PC* B - Singlemode
ST/PC*
*Requires double isolated “B” or “H” laser
Module Package D - Chassis Blind mate* R – Chassis Plug In M – Blue
OEM Link N – Yellow OEM Link** P – BLUE2 Link
*Blind mate modules only available with: RF: 75Ω BNC Optical:
SC/APC only
**For use in Satcom6
Module Package D - Chassis Blind mate* R – Chassis Plug In M – Blue
OEM Link N – Yellow OEM Link** P – BLUE2 Link
*Blind mate modules only available with: RF: 75Ω BNC Optical:
SC/APC only
**For use in Satcom6
Options 0 - No LNA feed [TX or RX] 1 - +5V LNA feed option out of
RF input [TX only]* 2 - +12V LNA feed option out of RF input [TX
only]* 3 - LNA/LNB/BUC external feed to RF connector from rack/rear
panel [TX/RX]* 4 - 20kb/s RS485/422/232 channel, No LNA feed
[TX/RX]** 5 - LNB control 13v/18v/22kHz tone [TX only]* 9 - 20kb/s
RS485/422/232 channel, external LNA feed to RF connector [TX/RX]**
B - Voltage transient protection on output, small value series
capacitor [RX only]* C - 20kb/s TTL channel, No LNA feed
[TX/RX]**
*Current limits apply, see detailed information for each module **
Digital link only in direction of RF link
Options 0 - No LNA feed [TX or RX] 1 - +5V LNA feed option out of
RF input [TX only]* 2 - +12V LNA feed option out of RF input [TX
only]* 3 - LNA/LNB/BUC external feed to RF connector from rack/rear
panel [TX/RX]* 4 - 20kb/s RS485/422/232 channel, No LNA feed
[TX/RX]** 5 - LNB control 13v/18v/22kHz tone [TX only]* 9 - 20kb/s
RS485/422/232 channel, external LNA feed to RF connector [TX/RX]**
B - Voltage transient protection on output, small value series
capacitor [RX only]* C - 20kb/s TTL channel, No LNA feed
[TX/RX]**
*Current limits apply, see detailed information for each module **
Digital link only in direction of RF link
Nominal Gain(dB) TX RX 0 -5 +5 2 NU +11 5 -15 +15 8 -11 +14
Nominal Gain(dB) TX RX 0 -5 +5 2 NU +11 5 -15 +15 8 -11 +14
TX/TRX/DTX Laser Transmitters only – receivers leave these blank H
- DFB, Dual isolated, 3mW ±20nm S - DFB, standard, 3mW ±20nm W -
DFB with WDM, 3mW ±20nm
TX/TRX/DTX Laser Transmitters only – receivers leave these blank H
- DFB, Dual isolated, 3mW ±20nm S - DFB, standard, 3mW ±20nm W -
DFB with WDM, 3mW ±20nm
Laser Wavelength Wavelength (nm) Type
1550 H,,S,W
1550 H,,S,W
Popular products HRT-L3-8R-38-S1550 L-Band 700-2450 MHz, 75 Ohm
BNC, Singlemode SC/APC, Rack plug-in module, Wavelength 1550 nm
HRR-L3-8R-08 L-Band 700-2450 MHz, 75 Ohm BNC, Singlemode SC/APC,
Rack plug-in module RF parameters for popular link gains
Link Tx Gain Rx Gain
Link Noise Figure (Default Tx Gain)
Link Noise Figure (Max Tx Gain)
Link P1dB (Default Tx Gain)
Link P1dB (Max Tx Gain)
HRT-L3-xx-x8-S1550 & HRR-L3-xx-x8 (3dB Gain Link)
-11 dB +14 dB 21 dB 13.5 dB -0 dBm -7.5 dBm
HRT-L3-xx-x5-S1550 & HRR-L1-xx-x5
(Unity Gain Link)
-15 dB +15 dB 25 dB 13.5 dB +2 dBm -8.5 dBm
HRT-L3-xx-x6-S1550 & HRR-L1-xx-x6
(Unity Gain Link)
-11 dB +11 dB 21 dB 13.5 dB 0 dBm -7.5 dBm
ELECTRONICS A Division of Av-Comm
24/9 Powells Road, Brookvale, NSW 2100, Australia +61 2 9939 4377
[email protected]
75 Ohm L-Band HTS 50km
Technical specification
Units L-Band HTS 75 ohms Transmitter HRT-L3-8D-38-S1550 (example)
Receiver HRR-L3-8D-08 (example) Frequency range MHz 700-2450
Impedance, RF connector 75Ω BNC, blind mate VSWR (typ) 1:1.5 Link
gain (Tx gain / Rx gain), default dB (nom) a +3 (-11 /+14) Tx gain
adjustment range dB (typ) 15.5 Tx gain adjustment from default gain
dB (typ) -7.5 to +8.0 Rx gain adjustment range dB (typ) 15.5 Rx
gain adjustment from default gain dB (typ) -7.5 to +8.0 Gain
adjustment step size Rx and Tx dB (typ) 0.5 Flatness, fullband dB
(max) a h ±1.4 Flatness, fullband dB (typ) a h ±0.6 Flatness, 36MHz
dB (typ) a ±0.2 Gain stability over temperature range dB (max) a ±3
Gain stability dB (typ) 0.25 @ 24 hrs Nominal input signal / output
signal dBm -20 / -20 IMD @ nominal output power dB (typ) c -50 CNR
@ nominal input power, 36MHz dB (typ) b 56 P1dBinput dBm (typ) a k
0 P1dBinput, at minimum Tx gain dBm (typ) a k 5 IP3input, at
default gain dBm (typ) a k 12 Noise figure, at default gain dB
(typ) a k 21 Noise figure, at maximum Tx gain dB (typ) a k 18 Noise
figure, 5dB optical loss dB (typ) c k 27
SFDR dB/Hz (typ) a 110
Test port gain, transmitter dB (typ) l -26 Test port gain, receiver
dB (typ) l -14 Test port flatness dB (typ) l ±1 Maximum input power
without damage dBm (min) 15 LNB power External 0-28V @ 350mA from
chassis power connector Power consumption Tx W (typ) 1.9 Power
consumption Rx W (typ) 1.3 Optical connector SC/APC, blind mate
Optical wavelength nm 1550 ± 20 Laser type DFB – (Distributed
feedback) laser Optical power output dBm (typ) 4.5 Summary alarm
output Open drain alarm: OPEN: Alarm, CURRENT SINK: okay Operating
temperature range e -20 °C to +60 °C Storage temperature range -40
°C to +70 °C Humidity RH 95% non-condensing humidity
a Nominal input power @ 0 dB optical loss
b Nominal input power @ 1 dB optical loss c Nominal output power @
5 dB optical loss h Default gain setting k Measured @ 1.2 GHz l
Relative to rear port @1.2 GHz All tests @ 25 °C after 15 minutes
warm up
e Datasheet parameters based on temperature range -10°C to +50°C,
refer to user manual for performance parameters @ -20 °C and +60
°C
ELECTRONICS A Division of Av-Comm
24/9 Powells Road, Brookvale, NSW 2100, Australia +61 2 9939 4377
[email protected]
75 Ohm L-Band HTS 50km
Accessories Type Key Features SNMP/Web Browser Card
Easy to use graphical user interface (GUI) Real time monitoring of
card performance Alarm monitoring and event logging Control of gain
adjustment Compatible with all ViaLiteHD rack chassis and modules
Easy integration with network management systems (NMS)
using management information base (MIB) tables Actively manage
redundancy switching New RF cards can be automatically reprogrammed
with the
previous card parameters Remote SNMP to local SNMP connection via
optical fiber Provides remote LAN 10/100 Ethernet link
Dual Redundancy
1:1 redundancy for L-Band Maximises link up-time Can be used to
backup copper coax Manual and automatic control via SNMP Flexible
configuration options Other redundancy options available
Rack Chassis
3U accepts up to 13 RF or Support cards, plus an SNMP card and dual
power supplies
A 1U chassis accepts up to 3 RF or Support cards or 2 cards and an
SNMP card (with dual power supplies)
Up to 26 channels per 3U chassis (using dual RF cards) – reducing
the amount of rack space required
Blind mate option All modules hot-swappable and auto
reconfiguration with
SNMP option On-card LNB and BUC power options Power fed through
rear chassis connector to card Bias Tees System can be monitored
and controlled remotely via SNMP
using a web browser
Outdoor Enclosures
CE approved and EMC compatible IP rated and NEMA approved Plug and
play format Suitable for harsh environments All modules hot
swappable Dual redundant power options Interface for monitor and
control (M&C) systems
ELECTRONICS A Division of Av-Comm
24/9 Powells Road, Brookvale, NSW 2100, Australia +61 2 9939 4377
[email protected]
[email protected]
ViaLiteHD_L_Band_75_Ohm_Datasheet_HRx-L1_DS_5.docx CR4505
20/07/2020
Due to our policy of continuing product development, these
specifications are subject to change and improvement without
notice.
ViaLiteHD® – L-Band HTS RF over Fiber Link
www.vialite.com +44 (0)1793 784389
[email protected] +1 (855)
4-VIALITE
75 Ohm L-Band HTS Standard 0-10 km link 65 dB dynamic range for 500
MHz traffic L-Band HTS (700-2450 MHz) 13/18 V and 22 KHz tone LNB
option Blind mate option Standard 5-year warranty
ViaLiteHD L-Band HTS fiber optic links have been designed for the
broadcast satellite industry to transport RF signals between
antennas and control rooms. Due to the very wide dynamic range, the
same link can be used in both the transmit and receive paths. This
dynamic range allows High Throughput Satellite (HTS) transponder
bandwidths of 500, 800 or even 1500 MHz to be transported, as well
as multiple standard 36 MHz transponders. The chassis cards are
available with the blind mate option, which allows all cables to be
connected at the rear of the chassis when installed. It also allows
configuration changes to be completed without disturbing the
connections and very fast changeover of cards; enabling five 9s
reliability. Options include: • 75 electrical connectors: BNC,
F-Type and MCX • Optical connectors: SC/APC, LC/APC, FC/APC and
E2000/APC • Test ports on Tx and Rx modules • Built-in BiasT for
LNB powering through RF connection • LNB control circuit with 13/18
VDC and 22 kHz tone • Blind mate connectivity (SC/APC and BNC) •
Serial digital channel to 20 kb/s on same optical path
Applications Broadcast facilities Mobile SNG, military and flyaways
Television Receive-Only (TVRO) Fixed satcom earth stations and
Teleports VSAT hubs (IP gateways) Marine antennas Telemetry,
Tracking and Command (TT&C) Oil and gas platforms
Formats 3U Chassis 1U Chassis Blue OEM and Blue2 Link Yellow OEM
Outdoor enclosures Related Products 50 km 1550 nm L-Band HTS 50 Ohm
L-Band HTS HTS 100 km+ systems DWDM links
L-BAND HTS RF OVER FIBER LINKS
ELECTRONICS A Division of Av-Comm
24/9 Powells Road, Brookvale, NSW 2100, Australia +61 2 9939 4377
[email protected]
75 Ohm L-Band HTS
33 88 33 6 7 98
UU LL DD 88 SS 13101310 13101310 10 11 12
Module Type R - Receiver(Optical in, RF out) V - Dual
Receiver(Optical in, RF out) T - Transmitter(RF in, optical out) U
- Dual Transmitter(RF In, optical out) X - Transceiver(Optical
in/out, RF out/in)
Module Type R - Receiver(Optical in, RF out) V - Dual
Receiver(Optical in, RF out) T - Transmitter(RF in, optical out) U
- Dual Transmitter(RF In, optical out) X - Transceiver(Optical
in/out, RF out/in)
H – ViaLiteHDH – ViaLiteHD
Electrical Connector 2 - F Type, 75Ω 3 - BNC, 75Ω 6 - MCX,
75Ω
Electrical Connector 2 - F Type, 75Ω 3 - BNC, 75Ω 6 - MCX,
75Ω
Frequency L - L Band HTS 700MHz-2450MHz Frequency L - L Band HTS
700MHz-2450MHz
Optical Connector 0 - No optical connector 1 - Multimode ST/PC* 2 -
Singlemode LC/PC* 3 - NU 4 - Singlemode FC/PC* 5 - Singlemode Lemo
2K* 6 - Singlemode FC/APC 7 - Singlemode E2000/APC 8 - Singlemode
SC/APC 9 - Singlemode LC/APC A - Singlemode SC/PC* B - Singlemode
ST/PC*
*Requires double isolated “B” or “H” laser
Optical Connector 0 - No optical connector 1 - Multimode ST/PC* 2 -
Singlemode LC/PC* 3 - NU 4 - Singlemode FC/PC* 5 - Singlemode Lemo
2K* 6 - Singlemode FC/APC 7 - Singlemode E2000/APC 8 - Singlemode
SC/APC 9 - Singlemode LC/APC A - Singlemode SC/PC* B - Singlemode
ST/PC*
*Requires double isolated “B” or “H” laser
Module Package D - Chassis Blind mate* R – Chassis Plug In M – Blue
OEM Link N – Yellow OEM Link** P - BLUE2 Link
*Blind mate modules only available with: RF: 75Ω BNC Optical:
SC/APC only
**For use in Satcom6
Module Package D - Chassis Blind mate* R – Chassis Plug In M – Blue
OEM Link N – Yellow OEM Link** P - BLUE2 Link
*Blind mate modules only available with: RF: 75Ω BNC Optical:
SC/APC only
**For use in Satcom6
Options 0 - No LNA feed [TX or RX] 1 - +5V LNA feed option out of
RF input [TX only]* 2 - +12V LNA feed option out of RF input [TX
only]* 3 - LNA/LNB/BUC external feed to RF connector from rack/rear
panel [TX/RX]* 4 - 20kb/s RS485/422/232 channel, No LNA feed
[TX/RX]** 5 - LNB control 13v/18v/22kHz tone [TX only]* 9 - 20kb/s
RS485/422/232 channel, external LNA feed to RF connector [TX/RX]**
B - Voltage transient protection on output, small value series
capacitor [RX only]* C - 20kb/s TTL channel, No LNA feed
[TX/RX]**
*Current limits apply, see detailed information for each module **
Digital link only in direction of RF link
Options 0 - No LNA feed [TX or RX] 1 - +5V LNA feed option out of
RF input [TX only]* 2 - +12V LNA feed option out of RF input [TX
only]* 3 - LNA/LNB/BUC external feed to RF connector from rack/rear
panel [TX/RX]* 4 - 20kb/s RS485/422/232 channel, No LNA feed
[TX/RX]** 5 - LNB control 13v/18v/22kHz tone [TX only]* 9 - 20kb/s
RS485/422/232 channel, external LNA feed to RF connector [TX/RX]**
B - Voltage transient protection on output, small value series
capacitor [RX only]* C - 20kb/s TTL channel, No LNA feed
[TX/RX]**
*Current limits apply, see detailed information for each module **
Digital link only in direction of RF link
Nominal Gain(dB) TX RX 0 -5 +5 2 NU +11 5 -15 +15 8 -11 +14
Nominal Gain(dB) TX RX 0 -5 +5 2 NU +11 5 -15 +15 8 -11 +14
TX/TRX/DTX Laser Transmitters only – receivers leave this
blank
H - DFB, Dual isolated, 3mW ±20nm S - DFB, standard, 3mW ±20nm W -
DFB with WDM, 3mW ±20nm
TX/TRX/DTX Laser Transmitters only – receivers leave this
blank
H - DFB, Dual isolated, 3mW ±20nm S - DFB, standard, 3mW ±20nm W -
DFB with WDM, 3mW ±20nm
Laser Wavelength Wavelength (nm) Type
1550 ,H,S,W
1550 ,H,S,W
Product Configurator Popular products HRT-L3-8R-38-S1310 L-Band
700-2450 MHz, 75 Ohm BNC, Singlemode SC/APC, Rack plug-in module,
Wavelength 1310 nm HRT-L3-8R-58-S1310 L-Band 700-2450 MHz, 75 Ohm
BNC, Singlemode SC/APC, Rack plug-in module, Wavelength 1310 nm
with switchable LNB control 13/18/22 V & 22 KHz tone
HRR-L3-8R-08 L-Band 700-2450 MHz, 75 Ohm BNC, Singlemode SC/APC,
Rack plug-in module RF parameters for popular link gains
Link Tx Gain Rx Gain
Link Noise Figure (Default Tx Gain)
Link Noise Figure (Max Tx Gain)
Link P1dB (Default Tx Gain)
Link P1dB (Max Tx Gain)
HRT-L3-xx-x8-S1310 & HRR-L1-xx-x8
(3dB Gain Link)
-11 dB +14 dB 21 dB 12.5 dB 0 dBm -7.5 dBm
HRT-L3-xx-x5-S1310 & HRR-L1-xx-x5
(Unity Gain Link)
-15 dB +15 dB 25 dB 13.5 dB +2 dBm -8.5 dBm
HRT-L3-xx-x8-S1310 & HRR-L1-xx-x2 (Low Noise Unity Gain
Link)
-11 dB +11 dB 21 dB 12.5 dB 0 dBm -7.5 dBm
1310 1310
ELECTRONICS A Division of Av-Comm
24/9 Powells Road, Brookvale, NSW 2100, Australia +61 2 9939 4377
[email protected]
75 Ohm L-Band HTS
Technical specification
Units L-Band HTS 75 ohms Transmitter HRT-L3-8D-38-S1310 (example)
Receiver HRR-L3-8D-08 (example) Frequency range MHz 700-2450
Impedance, RF connector 75Ω BNC, blind mate VSWR (typ) 1:1.5 Link
gain (Tx gain / Rx gain), default dB (nom) a +3 (-11 /+14) Tx gain
adjustment range dB (typ) 15.5 Tx gain adjustment from default gain
dB (typ) -7.5 to +8.0 Rx gain adjustment range dB (typ) 15.5 Rx
gain adjustment from default gain dB (typ) -7.5 to +8.0 Gain
adjustment step size Rx and Tx dB (typ) 0.5 Flatness, fullband dB
(max) a h ±1.4 Flatness, fullband dB (typ) a h ±0.6 Flatness, 36MHz
dB (typ) a ±0.2 Gain stability over temperature range dB (max) a ±3
Gain stability dB (typ) 0.25 @ 24 hrs Nominal input signal / output
signal dBm -20 / -20 IMD @ nominal output power dB (typ) c -50 CNR
@ nominal input power, 36MHz dB (typ) b 56 P1dBinput dBm (typ) a k
0 P1dBinput, at minimum Tx gain dBm (typ) a k 5 IP3input, at
default gain dBm (typ) a k 12 Noise figure, at default gain dB
(typ) a k 21 Noise figure, at maximum Tx gain dB (typ) a k 18 Noise
figure, 5dB optical loss dB (typ) c k 27
SFDR dB/Hz (typ) a 110
Test port gain, transmitter dB (typ) l -26 Test port gain, receiver
dB (typ) l -14 Test port flatness dB (typ) l ±1 Maximum input power
without damage dBm (min) 15 LNB power External 0-28V @ 350mA from
chassis power connector Power consumption Tx W (typ) 1.9 Power
consumption Rx W (typ) 1.3 Optical connector SC/APC, blind mate
Optical wavelength nm 1310 ± 20 Laser type DFB (Distributed
feedback) laser Optical power output dBm (typ) 4.5 Summary alarm
output Open drain alarm: OPEN: Alarm, CURRENT SINK: okay Operating
temperature range e -20 °C to +60 °C Storage temperature range -40
°C to +70 °C Humidity RH 95% non-condensing humidity
a Nominal input power @ 0 dB optical loss
b Nominal input power @ 1 dB optical loss c Nominal output power @
5 dB optical loss h Default gain setting k Measured @ 1.2 GHz l
Relative to rear port @1.2 GHz All tests @ 25 °C after 15 minutes
warm up
e Datasheet parameters based on temperature range -10°C to +50°C,
refer to user manual for performance parameters @ -20 °C and +60
°C
ELECTRONICS A Division of Av-Comm
24/9 Powells Road, Brookvale, NSW 2100, Australia +61 2 9939 4377
[email protected]
75 Ohm L-Band HTS
Accessories Type Key Features SNMP/Web Browser Card
Easy to use graphical user interface (GUI) Real time monitoring of
card performance Alarm monitoring and event logging Control of gain
adjustment Compatible with all ViaLiteHD rack chassis and cards
Easy integration with network management systems (NMS)
using management information base (MIB) tables Actively manage
redundancy switching New RF cards can be automatically reprogrammed
with the
previous card parameters Remote SNMP to local SNMP connection via
optical fiber Provides remote LAN 10/100 Ethernet link
Dual Redundancy
1:1 redundancy for L-Band Maximises link up-time Can be used to
backup copper coax Manual and automatic control via SNMP Flexible
configuration options Other redundancy options available
Rack Chassis
3U accepts up to 13 RF or Support cards, plus an SNMP card and dual
power supply
A 1U chassis accepts up to 3 RF or Support cards or 2 cards and an
SNMP card (with dual power supplies)
Up to 26 channels per 3U chassis (using dual RF cards) – reducing
the amount of rack space required
Blind mate option All modules hot-swappable and
auto-reconfiguration with
SNMP option On-card LNB and BUC power options Power fed through
rear chassis connector to card Bias Tees System can be monitored
and controlled remotely via SNMP
using a web browser
Outdoor Enclosures
CE approved and EMC compatible IP rated and NEMA approved Plug and
play format Suitable for harsh environments All modules hot
swappable Dual redundant power options Interface for monitor and
control (M&C) systems
ELECTRONICS A Division of Av-Comm
24/9 Powells Road, Brookvale, NSW 2100, Australia +61 2 9939 4377
[email protected]
[email protected]
ViaLiteHD_L_Band_50_Ohm_DWDM_MP_Datasheet_HRx-Lx-DCxx-DS-1.docx
CR3508 10/04/17
Due to our policy of continuing product development, these
specifications are subject to change and improvement without
notice.
ViaLiteHD® – L-Band HTS RF over Fiber Links
www.vialite.com +44 (0)1793 784389
[email protected] +1 (855)
4-VIALITE
50 DWDM Medium Power L-Band HTS L-Band HTS (700-2450MHz) Up to
500km systems available 1 to 96 channels per fiber Ideal for
Ka-Band rain fade diversity 5mW Laser Standard 5-year
warranty
ViaLiteHD DWDM L-Band HTS RF over fiber links use dense wavelength
division multiplexer (DWDM) lasers and have been designed for the
satellite industry to transport RF signals over long distances,
enabling Ka-Band diversity or remote location of antennas up to
500kms away. Due to the very wide dynamic range, the same link can
be used in both the transmit or receive paths. This dynamic range
allows High Throughput Satellite (HTS) transponder bandwidths of
500MHz, 800MHz or even 1500MHz to be transported, even over long
distances. A full suite of DWDM accessories is available as well as
system design, commissioning expertise and system setup. The
chassis cards are available with the ViaLiteHD blind mate option,
which allows all cables to be connected at the rear of the chassis
when installed. It also allows configuration changes to be
completed without disturbing the connections and very fast
changeover of cards; enabling five 9s reliability. Options include:
• 50 electrical connectors: SMA and MCX • Optical connectors:
SC/APC, LC/APC, FC/APC and E2000/APC • Test ports on Tx and Rx
modules • Built-in BiasT for LNB powering through RF connection •
LNB control circuit with 13/18VDC & 22kHz tone • Blind mate
connectivity (SC/APC and SMA)
Applications Ka-Band diversity rain-fade application Fixed satcom
earth stations and teleports Gateway reduction within a satellite
footprint Government installations Remote monitoring stations
Leased fiber reduction
Formats 3U Chassis 1U Chassis Yellow OEM Outdoor enclosures Related
Products 50km 1550nm L-Band HTS 75 Ohm DWDM L-Band HTS 100km+
systems
L-BAND HTS RF OVER FIBER LINKS
ELECTRONICS A Division of Av-Comm
24/9 Powells Road, Brookvale, NSW 2100, Australia +61 2 9939 4377
[email protected]
50 Ohm Medium Power DWDM L-Band HTS
Product configurator
11 88 55 6 7 98
UU LL DD 33 DD C33C33 10 11 12
Module Type R - Receiver(Optical in, RF out) T - Transmitter(RF in,
optical out)
Module Type R - Receiver(Optical in, RF out) T - Transmitter(RF in,
optical out)
H – ViaLiteHDH – ViaLiteHD
Electrical Connector 1 - SMA, 50Ω 5 - MCX, 50Ω
Electrical Connector 1 - SMA, 50Ω 5 - MCX, 50Ω
Frequency L - L Band HTS 700MHz-2450MHz Frequency L - L Band HTS
700MHz-2450MHz
Optical Connector 0 - No optical connector 1 - Multimode ST/PC* 2 -
Singlemode LC/PC* 3 - NU 4 - Singlemode FC/PC* 5 - Singlemode Lemo
2K* 6 - Singlemode FC/APC 7 - Singlemode E2000/APC 8 - Singlemode
SC/APC 9 - Singlemode LC/APC A - Singlemode SC/PC* B - Singlemode
ST/PC*
*Requires double isolated “B” or “H” laser
Optical Connector 0 - No optical connector 1 - Multimode ST/PC* 2 -
Singlemode LC/PC* 3 - NU 4 - Singlemode FC/PC* 5 - Singlemode Lemo
2K* 6 - Singlemode FC/APC 7 - Singlemode E2000/APC 8 - Singlemode
SC/APC 9 - Singlemode LC/APC A - Singlemode SC/PC* B - Singlemode
ST/PC*
*Requires double isolated “B” or “H” laser
Module Package D - Chassis Blindmate* R - Chassis Plug N – Yellow
OEM Link**
*Blindmate modules only available with: RF: 50Ω SMA or 75Ω BNC
Optical: SC/APC only
**For use in Satcom6
Module Package D - Chassis Blindmate* R - Chassis Plug N – Yellow
OEM Link**
*Blindmate modules only available with: RF: 50Ω SMA or 75Ω BNC
Optical: SC/APC only
**For use in Satcom6
Options 0 - No LNA feed [TX or RX] 1 - +5V LNA feed option out of
RF input [TX only]* 2 - +12V LNA feed option out of RF input [TX
only]* 3 - LNA/LNB/BUC external feed to RF connector from rack/rear
panel [TX/RX]* 5 - LNB control 13v/18v/22kHz tone [TX only]*
*Current limits apply, see detailed information for each
module
Options 0 - No LNA feed [TX or RX] 1 - +5V LNA feed option out of
RF input [TX only]* 2 - +12V LNA feed option out of RF input [TX
only]* 3 - LNA/LNB/BUC external feed to RF connector from rack/rear
panel [TX/RX]* 5 - LNB control 13v/18v/22kHz tone [TX only]*
*Current limits apply, see detailed information for each
module
Nominal Gain(dB) TX RX 0 -5 +5 2 NU +11 3 -11 +20 5 -15 +15 6 -25
+25 9 +0 +0
Nominal Gain(dB) TX RX 0 -5 +5 2 NU +11 3 -11 +20 5 -15 +15 6 -25
+25 9 +0 +0
Laser Wavelength Wavelength (nm) Type
DWDM D,E*
*DWDM wavelength range 1527.2158nm – 1577.0250nm. Laser Type
(digit10) + channel number (digit11, 3 characters) e.g. EC23 = DFB
12mW DWDM, channel C23, 1558.9831nm.
Laser Wavelength Wavelength (nm) Type
DWDM D,E*
*DWDM wavelength range 1527.2158nm – 1577.0250nm. Laser Type
(digit10) + channel number (digit11, 3 characters) e.g. EC23 = DFB
12mW DWDM, channel C23, 1558.9831nm.
TX D - DFB, DWDM, 5mW ±0.1nm E - DFB, DWDM, 12mW ±0.1nm
TX D - DFB, DWDM, 5mW ±0.1nm E - DFB, DWDM, 12mW ±0.1nm
Popular products HRT-L1-8D-50-DC33 L-Band HTS (700-2450MHz) chassis
plug-in DWDM transmitter with built-in LNB power, 50 ohm SMA and
SC/APC blind mate connectors HRR-L1-8D-03 L-Band HTS (700-2450MHz)
chassis plug-in transmitter, 50 ohm SMA and SC/APC blind mate
connectors HRT-L1-6N-30-DC33 L-Band HTS (700-2450MHz) Yellow OEM
DWDM transmitter with 50 ohm SMA and FC/APC connectors HRR-L1-8N-03
L-Band HTS (700-2450MHz) Yellow OEM receiver with 50 ohm SMA and
SC/APC connectors RF parameters for popular link gains
Link Tx Gain Rx Gain
Link Noise Figure (Default Tx Gain)
Link Noise Figure (Max Tx Gain)
Link P1dB (Default Tx Gain)
Link P1dB (Max Tx Gain)
HRT-L1-xx-x0-DC33 & HRR-L1-xx-x3
-5dB
(+5/-10.5dB)
+5dB
(+7.5/-8dB)
-15dB (+11.5/-4dB)
+15dB (+7.5/-9dB)
-25dB
(+5/-10.5dB)
+25dB
(+7.5/-9dB)
ELECTRONICS A Division of Av-Comm
24/9 Powells Road, Brookvale, NSW 2100, Australia +61 2 9939 4377
[email protected]
50 Ohm Medium Power DWDM L-Band HTS
Technical specification
Units 50 Ohm DWDM L-Band HTS Transmitter HRT-L1-8D-50-DC34
(example) Receiver HRR-L1-8D-03 (example) Frequency range MHz
700-2450 Impedance, RF connector 50Ω SMA, blind mate VSWR (typ)
1:1.5 Link gain (Tx gain / Rx gain), default dB (nom) a 15 (-5 /
+20) Tx gain adjustment range dB (typ) 15.5 Tx gain adjustment from
default gain dB (typ) -10.5 to +5 Rx gain adjustment range dB (typ)
15.5 Rx gain adjustment from default gain dB (typ) -8.0 to +7.5
Gain adjustment step size Rx and Tx dB (typ) 0.5 Flatness,
fullband, L-Band dB (max) a h ±1.5 Flatness, fullband, L-Band dB
(typ) a h ±0.5 Flatness, 36MHz, L-Band dB (typ) a ±0.2 Gain
stability over temperature range dB (max) a ±1 Gain stability dB
(typ) 0.25 @ 24 hrs Nominal input signal / output signal dBm -20 /
-20 IMD @ nominal output power dB (typ) c -69 CNR @ nominal input
power, 36MHz dB (typ) b 60 P1dBinput dBm (typ) a k -1.5 P1dBinput,
at maximum Tx gain dBm (typ) a k -6.5 IP3input, at default gain dBm
(typ) a k +11.5 Noise figure, at default gain dB (typ) a k 14 Noise
figure, at maximum Tx gain dB (typ) a k 9 Noise figure, 5dB optical
loss dB (typ) c k 19.5 SFDR dB/Hz (typ) a 114 Test port gain,
transmitter dB (typ) l -20 Test port gain, receiver dB (typ) l -20
Test port flatness dB (typ) l ±1 Maximum input power without damage
dBm 15 LNB power Internal 13/18/22V @ 700mA with switchable tone
Power Consumption Tx W (typ) 3.5, excluding LNA power Power
Consumption Rx W (typ) 1.3 Optical connector SC/APC, blindmate
Optical wavelength nm 1550.12 ± 0.16 Laser type DFB (Distributed
feedback), thermo-electric cooled laser Optical power output dBm
(typ) 7.0 Summary alarm output Open drain alarm: OPEN: Alarm,
CURRENT SINK: okay Operating temperature range -10°C to +50°C
Storage temperature range -40°C to +70°C Humidity RH 95%
non-condensing humidity
a Nominal input power @ 0dB optical loss b Nominal input power @
1dB optical loss c Nominal output power @ 5dB optical loss h
Default gain setting k Measured @ 1.2GHz l Relative to rear port
@1.2GHz All tests @ 25°C after 15 minutes warm up
ELECTRONICS A Division of Av-Comm
24/9 Powells Road, Brookvale, NSW 2100, Australia +61 2 9939 4377
[email protected]
50 Ohm Medium Power DWDM L-Band HTS
Accessories Type Key Features SNMP/Web Browser Card
Easy to use graphical user interface (GUI) Real time monitoring of
card performance Alarm monitoring and event logging Control of gain
adjustment Compatible with all ViaLiteHD rack chassis and modules
Easy integration with network management systems (NMS)
using management information base (MIB) tables Actively manage
redundancy switching New RF cards can be automatically reprogrammed
with the
previous card parameters Remote SNMP to local SNMP connection via
optical fiber Provides remote LAN 10/100 Ethernet link
Dual Redundancy
1:1 redundancy for L-Band Maximises link up-time Can be used to
backup copper coax Manual and automatic control via SNMP Flexible
configuration options Other options available
Rack Chassis
3U accepts up to 13 RF or Support cards, plus an SNMP card and dual
power supplies
A 1U chassis accepts up to 3 RF or Support cards or 2 cards and an
SNMP card (with dual power supplies)
Up to 26 channels per 3U chassis (using dual RF cards) – reducing
the amount of rack space required
Blind mate option All modules hot-swappable and
auto-reconfiguration with
SNMP option On-card LNB and BUC power options Power fed through
rear chassis connector to card Bias Tees System can be monitored
and controlled remotely via SNMP
using a web browser
ELECTRONICS A Division of Av-Comm
24/9 Powells Road, Brookvale, NSW 2100, Australia +61 2 9939 4377
[email protected]
[email protected]
ViaLiteHD_L_Band_50_Ohm_DWDM_HP_Datasheet_HRx-Lx-ECxx-DS-2.docx
CR3508 10/04/17
Due to our policy of continuing product development, these
specifications are subject to change and improvement without
notice.
ViaLiteHD® – L-Band HTS RF over Fiber Links
www.vialite.com +44 (0)1793 784389
[email protected] +1 (855)
4-VIALITE
50 DWDM High Power L-Band HTS L-Band HTS (700-2450MHz) Up to 500km
systems available 1 to 96 channels per fiber Ideal for Ka-Band rain
fade diversity Up to 100km with no EDFA 12mW Laser Standard 5-year
warranty
ViaLiteHD DWDM L-Band HTS RF over fiber links use dense wavelength
division multiplexer (DWDM) lasers and have been designed for the
satellite industry to transport RF signals over long distances,
enabling Ka-Band diversity or remote location of antennas up to
500kms away. Due to the very wide dynamic range, the same link can
be used in both the transmit or receive paths. This dynamic range
allows High Throughput Satellite (HTS) transponder bandwidths of
500MHz, 800MHz or even 1500MHz to be transported, even over long
distances. A full suite of DWDM accessories is available as well as
system design, commissioning expertise and system setup. The
chassis cards are available with the ViaLiteHD blind mate option,
which allows all cables to be connected at the rear of the chassis
when installed. It also allows configuration changes to be
completed without disturbing the connections and very fast
changeover of cards; enabling five 9s reliability. Options include:
• 50 electrical connectors: SMA and MCX • Optical connectors:
SC/APC, LC/APC, FC/APC and E2000/APC • Test ports on Tx and Rx
modules • Built-in BiasT for LNB powering through RF connection •
LNB control circuit with 13/18VDC & 22kHz tone • Blind mate
connectivity (SC/APC and SMA)
Applications Ka-Band diversity rain-fade application Fixed satcom
earth stations and teleports Gateway reduction within a satellite
footprint Government installations Remote monitoring stations
Leased fiber reduction
Formats 3U Chassis 1U Chassis Yellow OEM Outdoor enclosures Related
Products 50km 1550nm L-Band HTS 75 Ohm DWDM L-Band HTS 100km+
systems
L-BAND HTS RF OVER FIBER LINKS
ELECTRONICS A Division of Av-Comm
24/9 Powells Road, Brookvale, NSW 2100, Australia +61 2 9939 4377
[email protected]
50 DWDM High Power L-Band HTS
Product configurator
11 88 55 6 7 98
UU LL DD 00 EE C33C33 10 11 12
Module Type R - Receiver(Optical in, RF out) T - Transmitter(RF in,
optical out)
Module Type R - Receiver(Optical in, RF out) T - Transmitter(RF in,
optical out)
H – ViaLiteHDH – ViaLiteHD
Electrical Connector 1 - SMA, 50Ω 5 - MCX, 50Ω
Electrical Connector 1 - SMA, 50Ω 5 - MCX, 50Ω
Frequency L - L Band HTS 700MHz-2450MHz Frequency L - L Band HTS
700MHz-2450MHz
Optical Connector 0 - No optical connector 1 - Multimode ST/PC* 2 -
Singlemode LC/PC* 3 - NU 4 - Singlemode FC/PC* 5 - Singlemode Lemo
2K* 6 - Singlemode FC/APC 7 - Singlemode E2000/APC 8 - Singlemode
SC/APC 9 - Singlemode LC/APC A - Singlemode SC/PC* B - Singlemode
ST/PC*
*Requires double isolated “B” or “H” laser
Optical Connector 0 - No optical connector 1 - Multimode ST/PC* 2 -
Singlemode LC/PC* 3 - NU 4 - Singlemode FC/PC* 5 - Singlemode Lemo
2K* 6 - Singlemode FC/APC 7 - Singlemode E2000/APC 8 - Singlemode
SC/APC 9 - Singlemode LC/APC A - Singlemode SC/PC* B - Singlemode
ST/PC*
*Requires double isolated “B” or “H” laser
Module Package D - Chassis Blindmate* R - Chassis Plug N – Yellow
OEM Link**
*Blindmate modules only available with: RF: 50Ω SMA or 75Ω BNC
Optical: SC/APC only
**For use in Satcom6
Module Package D - Chassis Blindmate* R - Chassis Plug N – Yellow
OEM Link**
*Blindmate modules only available with: RF: 50Ω SMA or 75Ω BNC
Optical: SC/APC only
**For use in Satcom6
Options 0 - No LNA feed [TX or RX] 1 - +5V LNA feed option out of
RF input [TX only]* 2 - +12V LNA feed option out of RF input [TX
only]* 3 - LNA/LNB/BUC external feed to RF connector from rack/rear
panel [TX/RX]* 5 - LNB control 13v/18v/22kHz tone [TX only]*
*Current limits apply, see detailed information for each
module
Options 0 - No LNA feed [TX or RX] 1 - +5V LNA feed option out of
RF input [TX only]* 2 - +12V LNA feed option out of RF input [TX
only]* 3 - LNA/LNB/BUC external feed to RF connector from rack/rear
panel [TX/RX]* 5 - LNB control 13v/18v/22kHz tone [TX only]*
*Current limits apply, see detailed information for each
module
Nominal Gain(dB) TX RX 0 -5 +5 2 NU +11 3 -11 +20 5 -15 +15 6 -25
+25 9 +0 +0
Nominal Gain(dB) TX RX 0 -5 +5 2 NU +11 3 -11 +20 5 -15 +15 6 -25
+25 9 +0 +0
Laser Wavelength Wavelength (nm) Type
DWDM D,E*
*DWDM wavelength range 1527.2158nm – 1577.0250nm. Laser Type
(digit10) + channel number (digit11, 3 characters) e.g. EC23 = DFB
12mW DWDM, channel C23, 1558.9831nm.
Laser Wavelength Wavelength (nm) Type
DWDM D,E*
*DWDM wavelength range 1527.2158nm – 1577.0250nm. Laser Type
(digit10) + channel number (digit11, 3 characters) e.g. EC23 = DFB
12mW DWDM, channel C23, 1558.9831nm.
TX D - DFB, DWDM, 5mW ±0.1nm E - DFB, DWDM, 12mW ±0.1nm
TX D - DFB, DWDM, 5mW ±0.1nm E - DFB, DWDM, 12mW ±0.1nm
Popular products HRT-L1-8D-50-DC33 L-Band HTS (700-2450MHz) chassis
plug-in High Power DWDM transmitter with built-in LNB power, 50 ohm
SMA and SC/APC blind mate connectors HRR-L1-8D-00 L-Band HTS
(700-2450MHz) chassis plug-in transmitter, 50 ohm SMA and SC/APC
blind mate connectors HRT-L1-6N-30-EC33 L-Band HTS (700-2450MHz)
Yellow OEM High Power DWDM transmitter with 50 ohm SMA and FC/APC
connectors HRR-L1-8N-00 L-Band HTS (700-2450MHz) Yellow OEM
receiver with 50 ohm SMA and SC/APC connectors RF parameters for
popular link gains
Link Tx Gain Rx Gain
Link Noise Figure (Default Tx Gain)
Link Noise Figure (Max Tx Gain)
Link P1dB (Default Tx Gain)
Link P1dB (Max Tx Gain)
HRT-L1-xx-x0-EC33 & HRR-L1-xx-x3
-5dB
(+5/-10.5dB)
+5dB
(+7.5/-8dB)
-25dB (+5/-10.5dB)
+25dB (+7.5/-9dB)
ELECTRONICS A Division of Av-Comm
24/9 Powells Road, Brookvale, NSW 2100, Australia +61 2 9939 4377
[email protected]
50 DWDM High Power L-Band HTS
Technical specification
Units 50 Ohm DWDM L-Band HTS Transmitter HRT-L1-8D-50-EC34
(example) Receiver HRR-L1-8D-03 (example) Frequency range MHz
700-2450 Impedance, RF connector 50Ω SMA, blind mate VSWR (typ)
1:1.5 Link gain (Tx gain / Rx gain), default dB (nom) a 15 (-5 /
+20) Tx gain adjustment range dB (typ) 15.5 Tx gain adjustment from
default gain dB (typ) -10.5 to +5 Rx gain adjustment range dB (typ)
15.5 Rx gain adjustment from default gain dB (typ) -8.0 to +7.5
Gain adjustment step size Rx and Tx dB (typ) 0.5 Flatness,
fullband, L-Band dB (max) a h ±1.5 Flatness, fullband, L-Band dB
(typ) a h ±0.5 Flatness, 36MHz, L-Band dB (typ) a ±0.2 Gain
stability over temperature range dB (max) a ±1 Gain stability dB
(typ) 0.25 @ 24 hrs Nominal input signal / output signal dBm -20 /
-20 IMD @ nominal output power dB (typ) c -69 CNR @ nominal input
power, 36MHz dB (typ) b 60 P1dBinput dBm (typ) a k -1.5 P1dBinput,
at maximum Tx gain dBm (typ) a k -6.5 IP3input, at default gain dBm
(typ) a k +11.5 Noise figure, at default gain dB (typ) a k 14 Noise
figure, at maximum Tx gain dB (typ) a k 9 Noise figure, 5dB optical
loss dB (typ) c k 19.5 SFDR dB/Hz (typ) a 114 Test port gain,
transmitter dB (typ) l -20 Test port gain, receiver dB (typ) l -20
Test port flatness dB (typ) l ±1 Maximum input power without damage
dBm 15 LNB power Internal 13/18/22V @ 700mA with switchable tone
Power Consumption Tx W (typ) 3.5, excluding LNA power Power
Consumption Rx W (typ) 2.8 Optical connector SC/APC, blindmate
Optical wavelength nm 1550.12 ± 0.16 Laser type DFB (Distributed
feedback), thermo-electric cooled laser Optical power output dBm
(typ) 10.8 Summary alarm output Open drain alarm: OPEN: Alarm,
CURRENT SINK: okay Operating temperature range -10°C to +50°C
Storage temperature range -40°C to +70°C Humidity RH 95%
non-condensing humidity
a Nominal input power @ 0dB optical loss b Nominal input power @
1dB optical loss c Nominal output power @ 5dB optical loss h
Default gain setting k Measured @ 1.2GHz l Relative to rear port
@1.2GHz All tests @ 25°C after 15 minutes warm up
ELECTRONICS A Division of Av-Comm
24/9 Powells Road, Brookvale, NSW 2100, Australia +61 2 9939 4377
[email protected]
50 DWDM High Power L-Band HTS
Accessories Type Key Features SNMP/Web Browser Card
Easy to use graphical user interface (GUI) Real time monitoring of
card performance Alarm monitoring and event logging Control of gain
adjustment Compatible with all ViaLiteHD rack chassis and modules
Easy integration with network management systems (NMS)
using management information base (MIB) tables Actively manage
redundancy switching New RF cards can be automatically reprogrammed
with the
previous card parameters Remote SNMP to local SNMP connection via
optical fiber Provides remote LAN 10/100 Ethernet link
Dual Redundancy
1:1 redundancy for L-Band Maximises link up-time Can be used to
backup copper coax Manual and automatic control via SNMP Flexible
configuration options Other options available
Rack Chassis
3U accepts up to 13 RF or Support cards, plus an SNMP card and dual
power supplies
A 1U chassis accepts up to 3 RF or Support cards or 2 cards and an
SNMP card (with dual power supplies)
Up to 26 channels per 3U chassis (using dual RF cards) – reducing
the amount of rack space required
Blind mate option All modules hot-swappable and
auto-reconfiguration with
SNMP option On-card LNB and BUC power options Power fed through
rear chassis connector to card Bias Tees System can be monitored
and controlled remotely via SNMP
using a web browser
ELECTRONICS A Division of Av-Comm
24/9 Powells Road, Brookvale, NSW 2100, Australia +61 2 9939 4377
[email protected]
[email protected]
ViaLiteHD_L_Band_50_Ohm_50km_Datasheet_HRx-L1_DS_5.docx CR4505
29/07/2020
Due to our policy of continuing product development, these
specifications are subject to change and improvement without
notice.
ViaLiteHD® – L-Band HTS RF over Fiber Link
www.vialite.com +44 (0)1793 784389
[email protected] +1 (855)
4-VIALITE
50 Ohm L-Band HTS 50 km 10-50 km link 65 dB dynamic range for 500
MHz traffic L-Band HTS (700-2450 MHz) 13/18 V and 22 KHz tone LNB
option Blind mate option Standard 5-year warranty
ViaLiteHD L-Band HTS fiber optic 50 km links use 1550 nm lasers and
have been designed for the satellite industry to transport RF
signals between antennas and control rooms over fiber. Due to the
very wide dynamic range the same link can be used in both the
transmit and receive paths. This dynamic range allows High
Throughput Satellite (HTS) transponder bandwidths of 500, 800 or
even 1500 MHz to be transported, as well as multiple standard 36
MHz transponders. The chassis cards are available with the
ViaLiteHD blind mate option, which allows all cables to be
connected at the rear of the chassis when installed. It also allows
any configuration changes to be completed without disturbing the
connections and very fast changeover of cards; enabling five 9s
reliability. Options include: • 50 electrical connectors: SMA and
MCX • Optical connectors: SC/APC, LC/APC, FC/APC and E2000/APC •
Test ports on Tx and Rx modules • Built-in BiasT for LNB powering
through RF connection • LNB control circuit with 13/18 VDC and 22
kHz tone • Blind mate connectivity (SC/APC and SMA) • Serial
digital channel to 20 kb/s on same optical path
Applications
Fixed satcom earth stations and teleports Broadcast facilities
Mobile SNG, military and flyaways VSAT hubs (IP gateways) Marine
antennas Telemetry, Tracking and Command (TT&C) Oil and gas
platforms Television Receive-Only (TVRO)
Formats 3U Chassis 1U Chassis Blue OEM and Blue2 Link Yellow OEM
Outdoor enclosures Related Products 0-10km 1310nm L-Band HTS 75 Ohm
L-Band HTS HTS 100 km+ systems DWDM links
L-BAND HTS RF OVER FIBER LINKS
ELECTRONICS A Division of Av-Comm
24/9 Powells Road, Brookvale, NSW 2100, Australia +61 2 9939 4377
[email protected]
50 Ohm L-Band HTS 50km
Product configurator
11 88 55 6 7 98
UU LL DD 33 SS 15501550 15501550 10 11 12
Module Type R - Receiver(Optical in, RF out) V - Dual
Receiver(Optical in, RF out) T - Transmitter(RF in, optical out) U
- Dual Transmitter(RF In, optical out) X - Transceiver(Optical
in/out, RF out/in)
Module Type R - Receiver(Optical in, RF out) V - Dual
Receiver(Optical in, RF out) T - Transmitter(RF in, optical out) U
- Dual Transmitter(RF In, optical out) X - Transceiver(Optical
in/out, RF out/in)
H – ViaLiteHDH – ViaLiteHD
Electrical Connector 1 - SMA, 50Ω 5 - MCX, 50Ω
Electrical Connector 1 - SMA, 50Ω 5 - MCX, 50Ω
Frequency L - L Band HTS 700MHz-2450MHz Frequency L - L Band HTS
700MHz-2450MHz
Optical Connector 0 - No optical connector 1 - Multimode ST/PC* 2 -
Singlemode LC/PC* 3 - NU 4 - Singlemode FC/PC* 5 - Singlemode Lemo
2K* 6 - Singlemode FC/APC 7 - Singlemode E2000/APC 8 - Singlemode
SC/APC 9 - Singlemode LC/APC A - Singlemode SC/PC* B - Singlemode
ST/PC*
*Requires double isolated “B” or “H” laser
Optical Connector 0 - No optical connector 1 - Multimode ST/PC* 2 -
Singlemode LC/PC* 3 - NU 4 - Singlemode FC/PC* 5 - Singlemode Lemo
2K* 6 - Singlemode FC/APC 7 - Singlemode E2000/APC 8 - Singlemode
SC/APC 9 - Singlemode LC/APC A - Singlemode SC/PC* B - Singlemode
ST/PC*
*Requires double isolated “B” or “H” laser
Module Package D - Chassis Blindmate* R - Chassis Plug In M – Blue
OEM Link N – Yellow OEM Link** P – BLUE2 Link
*Blindmate modules only available with: RF: 50Ω SMA or 75Ω BNC
Optical: SC/APC only
**For use in Satcom6
Module Package D - Chassis Blindmate* R - Chassis Plug In M – Blue
OEM Link N – Yellow OEM Link** P – BLUE2 Link
*Blindmate modules only available with: RF: 50Ω SMA or 75Ω BNC
Optical: SC/APC only
**For use in Satcom6
Options 0 - No LNA feed [TX or RX] 1 - +5V LNA feed option out of
RF input [TX only]* 2 - +12V LNA feed option out of RF input [TX
only]* 3 - LNA/LNB/BUC external feed to RF connector from rack/rear
panel [TX/RX]* 4 - 20kb/s RS485/422/232 channel, No LNA feed
[TX/RX]** 5 - LNB control 13v/18v/22kHz tone [TX only]* 9 - 20kb/s
RS485/422/232 channel, external LNA feed to RF connector [TX/RX]**
B - Voltage transient protection on output, small value series
capacitor [RX only]* C - 20kb/s TTL channel, No LNA feed
[TX/RX]**
*Current limits apply, see detailed information for each module **
Digital link only in direction of RF link
Options 0 - No LNA feed [TX or RX] 1 - +5V LNA feed option out of
RF input [TX only]* 2 - +12V LNA feed option out of RF input [TX
only]* 3 - LNA/LNB/BUC external feed to RF connector from rack/rear
panel [TX/RX]* 4 - 20kb/s RS485/422/232 channel, No LNA feed
[TX/RX]** 5 - LNB control 13v/18v/22kHz tone [TX only]* 9 - 20kb/s
RS485/422/232 channel, external LNA feed to RF connector [TX/RX]**
B - Voltage transient protection on output, small value series
capacitor [RX only]* C - 20kb/s TTL channel, No LNA feed
[TX/RX]**
*Current limits apply, see detailed information for each module **
Digital link only in direction of RF link
Nominal Gain(dB) TX RX 0 -5 +5 2 NU +11 3 -11 +20 5 -15 +15 6 -25
+25
Nominal Gain(dB) TX RX 0 -5 +5 2 NU +11 3 -11 +20 5 -15 +15 6 -25
+25
TX/TRX/DTX Laser H - DFB, Dual isolated, 3mW ±20nm S - DFB,
standard, 3mW ±20nm W - DFB with WDM, 3mW ±20nm
TX/TRX/DTX Laser H - DFB, Dual isolated, 3mW ±20nm S - DFB,
standard, 3mW ±20nm W - DFB with WDM, 3mW ±20nm
Laser Wavelength Wavelength (nm) Type
1550 H,S,W
1550 H,S,W
Popular products HRT-L1-8R-33-S1550 L-Band 700-2450 MHz, 50 Ohm
SMA, Singlemode SC/APC, Rack plug-in module, Wavelength 1550 nm
HRR-L1-8R-03 L-Band 700-2450 MHz, 50 Ohm SMA, Singlemode SC/APC,
Rack plug-in module RF parameters for popular link gains
Link Tx Gain Rx Gain
Link Noise Figure (Default Tx Gain)
Link Noise Figure (Max Tx Gain)
Link P1dB (Default Tx Gain)
Link P1dB (Max Tx Gain)
HRT-L1-xx-x3-S1550 & HRR-L1-xx-x3 (9dB Gain Link)
-11 dB +20 dB 20 dB 12.5 dB -1 dBm -8.5 dBm
HRT-L1-xx-x5-S1550 & HRR-L1-xx-x5
(Unity Gain Link)
-15 dB +15 dB 24 dB 12.5 dB +3 dBm -8.5 dBm
HRT-L1-xx-x6-S1550 & HRR-L1-xx-x6
(High P1dB Unity Gain Link)
-25 dB +25 dB 34 dB 29 dB +13 dBm +9 dBm
ELECTRONICS A Division of Av-Comm
24/9 Powells Road, Brookvale, NSW 2100, Australia +61 2 9939 4377
[email protected]
50 Ohm L-Band HTS 50km
Technical specification
Units Note L-Band HTS 50 ohms Transmitter (Tx) HRT-L1-8R-33-S1310
(example) Rece