Embed Size (px)
Citation preview
Zombicide Box OrganizerBy R&H Firefly Workshops
Box Organizer Includes:
Step by Step Instructions•Removable Character/Zombie Tray (Qty. 1)•Removable Character/Zombie Tray Lid (Qty. 1)•Removable Token Tray (Qty. 2)•Removable Token Tray Lid (Qty. 1)•Removable Card Tray (Qty. 1)•Removable Card Tray Lid (Qty. 1)•Removable Card Dividers (Qty. 9)•
Need extra Card Dividers or have missing/damaged parts? Have comments or questions?Contact us at:
[email protected]@gmail.com
Zombicide Box OrganizerBy R&H Firefly Workshops
Step 1: Separate all of the pieces from their frames.
Step 2: Assemble as both of the slotted dividers as shown. Repeat this step 2 times.
Set aside untill Step 4.
Page 2
*Tip - Fully assemble eachstep to ensure a proper fit and location of every piece.All separators and dividerswill be flush on the topwhen properly installed.
Once each step is assembledcorrectly, disassemble andreassemble while adding a smalldrop of super glue to everyintersection where the partsslide together. Wipe all extra superglue off of the outside edges witha clean rag.
Zombicide Box Organizer (con't)
Step 3: Assemble as both of the slotted dividers as shown. Repeat this step 2 times.
Page 3
Mounting Holes
From Step 2
From Step 3
Zombicide Box Organizer (con't)
Page 4
Step 5: Assemble the 2 Corners and Wall as shown. Please note the # of mounting holes in the rear wall. Repeat this step 2 times.
Zombicide Box Organizer (con't)
Page 4
Step 5: Assemble the 2 remaining Walls as shown. Insert into the bottom section of the box and set aside untill step 10.
Zombicide Box Organizer (con't)
Page 5
Step 6: Assemble the Card Tray as shown. Set aside until Step 10.
Bottom Panel
Zombicide Box Organizer (con't)
Page 6
Step 7: Assemble the Character Tray as shown. Insert the Center Divider into the Bottom Panel first. Finish by inserting the 3 Removable Dividers (not shown). Set aside until Step 11.
Do not glue the Removable Dividers unless desired.
Zombicide Box Organizer (con't)
Page 7
Step 8: Assemble the Token Tray as shown. Repeat this step 2 times.
Zombicide Box Organizer (con't)
Page 8
Step 9: Assemble the Token Tray as shown. Repeat this step 2 times and set aside untill Step 12.
Zombicide Box Organizer (con't)
Page 9
Step 10: Inserting the Card Tray into the main organizer assembly. Do not glue the tray in place.
*Do not glue the Removable Dividers (unless desired) or cover in place.
Zombicide Box Organizer (con't)
Page 10
Step 11: Finish by inserting the character and token trays into the main organizer assembly. The two token trays are designed to fit together with the lid on top. Do not glue the trays in place.
*Do not glue the divider (unless desired) or covers in place.
Step 11: Inserting the Zombie Tray into the main organizer assembly. Do not glue the tray in place.
*Do not glue the cover in place.
Zombicide Box Organizer (con't)
Page 11
Step 11: Finish by inserting both of the Token Trays and Lid into the main organizer assembly. Do not glue the tray in place.
*Do not glue the cover in place.
