ZQ110 6. iOS MFi Mode Setting (Optional)6. iOS MFi Mode Setting (Optional) This product supports Made for iOS (MFi) mode which enables Bluetooth communication with iOS devices. •

Rev. 1.00 - 32 -

ZQ110

Mobile Printer User Manual

6. iOS MFi Mode Setting (Optional) This product supports Made for iOS (MFi) mode which enables Bluetooth communication with iOS devices. • How to enable and disable MFi mode: 1. Turn on the printer. 2. Open the media cover. 3. Press and hold the power button and paper feed button for more than two seconds. 4. Close the cover when you hear a beep. 5. Reboot the printer when the following message is printed:

- iOS mode enable!! Please Reboot Printer!!

6. To disable MFi mode, repeat the above procedure.

• Check iOS mode: 1. Execute a self-test. 2. If the printed firmware version contains a lowercase “a” (for example: V01.00 STDa),

iOS mode is disabled. 3. If the printed firmware version contains a lowercase “i” (for example: V01.00 STDi),

iOS mode is enabled.

P1069089-001 Rev. 1.00

ZQ110 Mobile Printer Bluetooth and iOS

Connection Manual

Rev. 1.00 - 2 -

ZQ110

Mobile Printer Bluetooth Connection Manual

Table of Contents 1. Manual Information ........................................................................................................ 6

2. Precautions .................................................................................................................... 6

3. Made For iOS® (MFi) Mode Change ............................................................................. 6

4. Bluetooth Connection Instructions .............................................................................. 7

5. Troubleshooting........................................................................................................... 11

Rev. 1.00 - 3 -

ZQ110


■ Proprietary Statements This manual contains proprietary information for Zebra Technologies Corporation. It is

intended solely for the information and use of parties operating and maintaining the equip-

ment described herein. Such proprietary information may not be used, reproduced, or dis-

closed to any other parties for any other purpose without the expressed written permission

of Zebra Technologies Corporation.

Product Improvements

Since continuous product improvement is a policy of Zebra Technologies Corporation, all

specifications and signs are subject to change without notice.

FCC Compliance Statement NOTE: This equipment has been tested and found to comply with the limits of a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This equip-

ment generates, uses and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful interference with radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment to an outlet or circuit different from that to which the receiver is

connected.

• Consult the dealer or an experienced radio/TV technician for help.

WARNING: Exposure to Radio Frequency radiation. To conform to FCC RF exposure re-

quirements this device shall be used in accordance with the operating conditions and in-

structions listed in this manual.

NOTE: This unit was tested with shielded cables on the peripheral devices. Shielded

cables must be used with the unit to ensure compliance.

Changes or modifications to this unit not expressly approved by Zebra Technologies

Corporation could void the user’s authority to operate this equipment.

Rev. 1.00 - 4 -

ZQ110


Canadian Compliance Statement This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme á la norme NMB-003 du Canada.

“IC:” before the equipment certification number signifies that the Industry Canada technical

specifications were met. It does not guarantee that the certified product will operate to the

user’s satisfaction.

Liability Disclaimer Inasmuch as every effort has been made to supply accurate information in this manual,

Zebra Technologies Corporation is not liable for any erroneous information or omissions.

Zebra Technologies Corporation reserves the right to correct any such errors and

disclaims liability resulting therefrom.

No Liability for Consequential Damage

In no event shall Zebra Technologies Corporation or anyone else involved in the creation,

production, or delivery of the accompanying product (including hardware and software) be

liable for any damages whatsoever (including, without limitation, damages for loss of

business profits, business interruption, loss of business information, or other pecuniary

loss) arising out of the use of or the results of use of or inability to use such product, even

if Zebra Technologies Corporation has been advised of the possibility of such damages.

Because some states do not allow the exclusion of liability for consequential or incidental

damages, the above limitation may not apply to you.

Rev. 1.00 - 5 -

ZQ110


Copyrights

The copyrights in this manual and the label print engine described therein are owned by

Zebra Technologies Corporation. Unauthorized reproduction of this manual or the software

in the label print engine may result in imprisonment of up to one year and fines of up to

$10,000 (17 U.S.C.506). Copyright violators may be subject to civil liability.

This product may contain ZPL® , ZPL II® , and ZebraLink™ programs; Element Energy

Equalizer® Circuit; E3® ; and AGFA fonts. Software © ZIH Corp. All rights reserved

worldwide.

ZebraLink and all product names and numbers are trademarks, and Zebra, the Zebra logo,

ZPL, ZPL II, Element Energy Equalizer Circuit, and E3 Circuit are registered trademarks of

ZIH Corp. All rights reserved worldwide.

Monotype® , Intellifont® and UFST® are trademarks of Monotype Imaging, Inc. registered

in the United States Patent and Trademark Office and may be registered in certain

jurisdictions.

Andy™, CG Palacio™, CG Century Schoolbook™, CG Triumvirate™, CG Times™,

Monotype Kai™, Monotype Mincho™ and Monotype Sung™ are trademarks of Monotype

Imaging, Inc. and may be registered in some jurisdictions.

HY Gothic Hangul™ is a trademark of Hanyang Systems, Inc.

Angsana™ is a trademark of Unity Progress Company (UPC) Limited.

Andale® , Arial® , Book Antiqua® , Corsiva® , Gill Sans® , Sorts® and Times New Roman®

are trademarks of The Monotype Corporation registered in the United States Patent and

Trademark Office and may be registered in certain jurisdictions.

Century Gothic™, Bookman Old Style™ and Century Schoolbook™ are trademarks of The

Monotype Corporation and may be registered in certain jurisdictions.

HGPGothicB™ is a trademark of the Ricoh company, Ltd. and may be registered in some

jurisdictions.

Univers™ is a trademark of Heidelberger Druckmaschinen AG, which may be registered in

certain jurisdictions, exclusively licensed through Linotype Library GmbH, a wholly owned

subsidiary of Heidelberger Druckmaschinen AG.

Futura® is a trademark of Bauer Types SA registered in the United States Patent and

Trademark Office and may be registered in some jurisdictions.

TrueType® is a trademark of Apple Computer, Inc. registered in the United States Patent

and Trademark Office and may be registered in certain jurisdictions.

All other product names are the property of their respective owners.

All other brand names, product names, or trademarks belong to their respective holders.

© 2014 ZIH Corp.

Rev. 1.00 - 6 -

ZQ110


1. Manual Information This ZQ110 Mobile Printer Bluetooth Connection Manual provides information on the connection of Bluetooth-enabled iOS devices with the printer.

2. Precautions 1. To connect the printer with another device via Bluetooth, the device must be within 10

meters of the printer. The connection will be broken if the distance between devices exceeds 10 meters.

2. The maximum distance between devices must be shortened if transmission obstacles,

such as cement walls, are present. 3. If a device (such as a microwave oven, wireless LAN, etc.) that uses the same

frequency is present, transmission may experience interference. Separate the printer and Bluetooth-enabled device from the interference by a distance of at least 5 meters.

3. Made For iOS® (MFi) Mode Change MFi mode is available for Bluetooth communication. If MFi mode is enabled, Bluetooth communication will be only possible with an iOS device. To enable or disable MFI Mode, perform the following procedure:

1. Turn on the printer power. 2. With the printer cover open, press and hold down the power button and the feed button

for 2 seconds. 3. After the beep sounds, close the cover. 4. Check for the following message: iOS mode enabled!! Please Reboot Printer!! 5. Reboot the printer. Repeat steps 1-5 to disable MFi mode. To check whether iOS Mode is enabled or disabled, perform the following procedure:

Implement the printer’s Self Test a. If the firmware version is Vxx.xx STDa, iOS mode is disabled. b. If the firmware version is Vxx.xx STDi, iOS mode is enabled.

wkempel

Highlight

Rev. 1.00 - 7 -

ZQ110


4. Bluetooth Connection Instructions To enable iOS mode, perform the following procedure:

1) Select the Settings icon. 2) Select “General”.

3) Select “Bluetooth”. 4) Select the printer to connect.

Rev. 1.00 - 8 -

ZQ110


5) Enter the printer’s PIN (default: 0000). 6) Select “Pair”

7) Bluetooth communication is connected.

Rev. 1.00 - 9 -

ZQ110


To enable Android mode (iOS mode disable), perform the following procedure:

1) Select the Settings icon. 2) Select “Bluetooth”.

3) Select the printer to connect. 4) Enter the printer’s PIN (default : 0000).

Rev. 1.00 - 10 -

ZQ110


5) Select “OK”. 6) Bluetooth communication is connected.

Rev. 1.00 - 11 -

ZQ110


5. Troubleshooting If the iOS device cannot discover or pair with the printer, check the following: 1. Perform a self test to check if the printer has iOS mode enabled. 2. Check whether the printer is connected to another iOS device. (If the printer is

connected to another iOS device, it cannot be discovered by (or paired with) your iOS device.)

3. Press the Feed button. If the STATUS LED blinks when you press the Feed button, it

means that the printer is connected to another iOS device. You must disconnect the connection to the other iOS device, or turn on the printer again while the printer cover is opened*.

* A printer is automatically connected to the last iOS device which was connected in iOS mode. But, the printer does not make a connection to any device, if it is turned on with the printer cover open.

www.zebra.com

Zebra Technologies International, LLC Zebra Technologies Europe Limited 475 Half Day Road Dukes Meadow Suite 500, Lincolnshire Millboard Road Illinois 60069 USA Bourne End Phone: +1.847.634.6700 Buckinghamshire, SL8 5XF, UK Toll-Free: +1.800.230.9494 Phone: +44 (0)1628 556000 Fax: +1.847.913.8766 Fax: +44 (0)1628 556001

P1069078-001 Rev. A

ZQ110 Mobile Printer iOS Utility Manual

ZQ110

Rev. 1.00 - 2 - Mobile Printer iOS Utility Manual

Table of Contents 1. Manual Information ........................................................................................................ 6 2. Operating Environment ................................................................................................. 6

2-1 Supported Platform ..................................................................................................... 6 2-2 Supported Interfaces .................................................................................................. 6 2-3 Supported Devices ..................................................................................................... 6

3. Utility Usage ................................................................................................................... 7

3-1 Main Screen ............................................................................................................... 7 3-2 Utility Version .............................................................................................................. 8 3-3 Target Setting .............................................................................................................. 8 3-4 VMSM (Virtual Memory Switch Manager) ................................................................. 10 3-5 NV Image Manager ................................................................................................... 12 3-6 Demonstration .......................................................................................................... 13

3-6-1 Demonstration Menu .................................................................................... 14

ZQ110


■ Proprietary Statements This manual contains proprietary information for Zebra Technologies Corporation. It is

intended solely for the information and use of parties operating and maintaining the equip-

ment described herein. Such proprietary information may not be used, reproduced, or dis-

closed to any other parties for any other purpose without the expressed written permission

of Zebra Technologies Corporation.

Product Improvements

Since continuous product improvement is a policy of Zebra Technologies Corporation, all

specifications and signs are subject to change without notice.

FCC Compliance Statement NOTE: This equipment has been tested and found to comply with the limits of a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This equip-

ment generates, uses and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful interference with radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment to an outlet or circuit different from that to which the receiver is

connected.

• Consult the dealer or an experienced radio/TV technician for help.

WARNING: Exposure to Radio Frequency radiation. To conform to FCC RF exposure re-

quirements this device shall be used in accordance with the operating conditions and in-

structions listed in this manual.

NOTE: This unit was tested with shielded cables on the peripheral devices. Shielded

cables must be used with the unit to ensure compliance.

Changes or modifications to this unit not expressly approved by Zebra Technologies

Corporation could void the user’s authority to operate this equipment.

ZQ110


Canadian Compliance Statement This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme á la norme NMB-003 du Canada.

“IC:” before the equipment certification number signifies that the Industry Canada technical

specifications were met. It does not guarantee that the certified product will operate to the

user’s satisfaction.

Liability Disclaimer Inasmuch as every effort has been made to supply accurate information in this manual,

Zebra Technologies Corporation is not liable for any erroneous information or omissions.

Zebra Technologies Corporation reserves the right to correct any such errors and

disclaims liability resulting therefrom.

No Liability for Consequential Damage

In no event shall Zebra Technologies Corporation or anyone else involved in the creation,

production, or delivery of the accompanying product (including hardware and software) be

liable for any damages whatsoever (including, without limitation, damages for loss of

business profits, business interruption, loss of business information, or other pecuniary

loss) arising out of the use of or the results of use of or inability to use such product, even

if Zebra Technologies Corporation has been advised of the possibility of such damages.

Because some states do not allow the exclusion of liability for consequential or incidental

damages, the above limitation may not apply to you.

ZQ110


Copyrights

The copyrights in this manual and the label print engine described therein are owned by

Zebra Technologies Corporation. Unauthorized reproduction of this manual or the software

in the label print engine may result in imprisonment of up to one year and fines of up to

$10,000 (17 U.S.C.506). Copyright violators may be subject to civil liability.

This product may contain ZPL® , ZPL II® , and ZebraLink™ programs; Element Energy

Equalizer® Circuit; E3® ; and AGFA fonts. Software © ZIH Corp. All rights reserved

worldwide.

ZebraLink and all product names and numbers are trademarks, and Zebra, the Zebra logo,

ZPL, ZPL II, Element Energy Equalizer Circuit, and E3 Circuit are registered trademarks of

ZIH Corp. All rights reserved worldwide.

Monotype® , Intellifont® and UFST® are trademarks of Monotype Imaging, Inc. registered

in the United States Patent and Trademark Office and may be registered in certain

jurisdictions.

Andy™, CG Palacio™, CG Century Schoolbook™, CG Triumvirate™, CG Times™,

Monotype Kai™, Monotype Mincho™ and Monotype Sung™ are trademarks of Monotype

Imaging, Inc. and may be registered in some jurisdictions.

HY Gothic Hangul™ is a trademark of Hanyang Systems, Inc.

Angsana™ is a trademark of Unity Progress Company (UPC) Limited.

Andale® , Arial® , Book Antiqua® , Corsiva® , Gill Sans® , Sorts® and Times New Roman®

are trademarks of The Monotype Corporation registered in the United States Patent and

Trademark Office and may be registered in certain jurisdictions.

Century Gothic™, Bookman Old Style™ and Century Schoolbook™ are trademarks of The

Monotype Corporation and may be registered in certain jurisdictions.

HGPGothicB™ is a trademark of the Ricoh company, Ltd. and may be registered in some

jurisdictions.

Univers™ is a trademark of Heidelberger Druckmaschinen AG, which may be registered in

certain jurisdictions, exclusively licensed through Linotype Library GmbH, a wholly owned

subsidiary of Heidelberger Druckmaschinen AG.

Futura® is a trademark of Bauer Types SA registered in the United States Patent and

Trademark Office and may be registered in some jurisdictions.

TrueType® is a trademark of Apple Computer, Inc. registered in the United States Patent

and Trademark Office and may be registered in certain jurisdictions.

All other product names are the property of their respective owners.

All other brand names, product names, or trademarks belong to their respective holders.

© 2014 ZIH Corp.

ZQ110


1. Manual Information This manual contains detailed instructions on the usage of the printer utility for iOS-based devices. At Zebra, we maintain ongoing efforts to enhance and upgrade the functions and quality of our products. Therefore, product specifications and user manuals are subject to change without prior notice.

2. Operating Environment

2-1 Supported Platform

• iOS 5.1.1 or higher

2-2 Supported Interfaces The following interfaces are supported: • Ethernet • Bluetooth

2-3 Supported Devices The following devices have been verified to work.

• iPhone 4G / 5G

• iPad2/iPad mini

ZQ110


3. Utility Usage

3-1 Main Screen 1) Launch the Utility. 2) The following screen will be displayed.

3) Tap each button once. The button expands and moves to the center of the screen The button’s description appears at the bottom.

4) Tap the center button once again to perform the desired function. All the functions except for Lookup/Info are available for use after the Target Printer is set.

ZQ110


3-2 Utility Version

1) Tap the “Info” icon or button. 2) The version information will display as follows:

3-3 Target Setting

To use the Utility, set the target printer. 1) Tap or click Lookup.

ZQ110


2) From the list of available printers, select your printer.

3) The message will display: “Target is selected”. Tap Done to return to the main screen.

4) The model number of the Target Printer displays in the top right-hand corner as

shown below.

ZQ110


3-4 VMSM (Virtual Memory Switch Manager) 1) Launch the VMSM.

2) When the VMSM is launched as shown in the image below, select the item from the menu.

3-1

3-3

3-4

3-2

ZQ110


3) View and Change the Settings 3-1) Printer Setting

- You can view and change the Power Saving Time, Emulation, Default Font, Print Speed and Code Page settings.

Item Description Label Mode Configure the MSR Trigger Mode.

Printer Density Adjust the print density on the printer.

Print Speed Adjust the print speed.

Default Code Page Change the default Code Page.

Single byte Font Selection Set the Single byte font. Font A: 12X24 Font B: 9X24 Font C: 9X17

Beep for paper end Select whether to activate a beep sound when the printer is out of paper.

Beep for low battery Select whether to activate a beep sound when the battery is low.

Double byte character mode Select whether to activate the 2-byte character mode. ※ The double byte font is available to select on the

printer that supports Chinese, Japanese and Korean.

Auto Power Off Time Set the idle time before the printer automatically turns off.

Auto Power Saving Time Set the idle time before the printer goes into power saving mode.

3-2) MSR Configuration

- You can view and change the MSR configurations.

Item Description MSR Trigger Mode Configure the MSR Trigger Mode.

MSR Data Mode Configure the MSR Data Mode.

MSR Sentinel Characters Configure the MSR Sentinel characters.

3-3) Set Status of printer

- Tap this button to apply new settings to the printer, otherwise they will be lost. 3-4) Get Status of printer

- Check the status of the printer.

4) Quit

Tap Done button to return to the main screen.

ZQ110


3-5 NV Image Manager Launch the NV Image Manager.

1) Camera - Activate the Camera mode to take pictures. 2) Get Image: - Import images from your photo albums. 3) Download - Download images from the Image View. 4) Refresh: - Read the memory allocated to the NV areas of the printer. 5) Print: - Print from the selected memory. 6) Print All: - Print from all the allocated memories. 7) Remove: - Delete the selected memory. 8) Remove All: - Delete all the allocated memories.

1

2

3

4

5

6

7

8

ZQ110


3-6 Demonstration Demonstrate the functions of the printer.

1) Tap Connect to Printer. 2) Check printer status in real time

- Select whether to check the status of the printer in real time. 3) Text - Print the text that is entered. 4) Bitmap - Print image files. 5) Barcode - Print barcodes. 6) MSR - The MSR function is available. - The MSR function must be supported by the printer. ※ The buttons are deactivated if their functions are not available.

1

3

4

2

5

6

ZQ110


3-6-1 Demonstration Menu - At least one line of line feed characters must be entered to print. - Select an area of the text to print and tap the Send button. 1) Text - Print text.

1-1) Enter text. - At least one line of line feed characters must be entered to print the entire line. - Select an area of the text to print and tap the Send button.

1-2) Change the alignment option. 1-3) Select the Text Encoding format.

- KSC5601: Korean language is supported. - SHIFT-JIS: Japanese language is supported. - BIG5/GB2312/GB18030: Chinese language is supported. - Custom: code page can be specified by users.

Double-byte fonts (KSC5601 / SHIFT-JIS / BIG5 / GB2312 / GB18030) must be supported by the printer to use them. Non-alphanumeric characters in a single-byte font may require custom encoding.

1-4) Select the Width / Height of a character. 1-5) Change the character attributes.

- Default: no attributes are specified. - BOLD: print in bold letters. - UNDERLINE: print in underlined letters. - REVERSE: print in reversed letters.

1-1

1-2

1-3

1-4

1-5

Send

ZQ110


2) Bitmap - Print image.

2-1) Use the Progress Bar to adjust the brightness level of an image. Sliding it to the right will make the image brighter.

2-2) The Progress Bar can be specified. The printed image will be brighter. 2-3) Camera: take a picture using the built-in camera. 2-4) Get Image: import images from the photo album. 2-5) Print: print the selected image.

2-1 2-2

2-3

2-4

2-5

ZQ110


3) Barcode - Print barcode.

3-1) Enter barcode data. 3-2) The barcode type will display.

It can be selected at “3-4) Change Barcode Type”. 3-3) Width/Height: adjust the Width/Height of a barcode. 3-4) The barcode type can be selected among the ones supported by the printer. 3-5) Print the barcode. 3-6) Print all barcodes. 3-7) The barcode type/contents can be identified using the built-in camera on your

iPhone.

3-1

3-3

3-4

3-5

3-6

3-7

3-2

ZQ110


4) MSR - Read MSR card.

4-1) The data will display if the MSR card reading is successful. 4-2) The MSR read mode will start.

4-1

4-2

www.zebra.com

Zebra Technologies International, LLC Zebra Technologies Europe Limited 475 Half Day Road Dukes Meadow Suite 500, Lincolnshire Millboard Road Illinois 60069 USA Bourne End Phone: +1.847.634.6700 Buckinghamshire, SL8 5XF, UK Toll-Free: +1.800.230.9494 Phone: +44 (0)1628 556000 Fax: +1.847.913.8766 Fax: +44 (0)1628 556001

Documents

ZQ110 6. iOS MFi Mode Setting (Optional)6. iOS MFi Mode Setting (Optional) This product supports Made for iOS (MFi) mode which enables Bluetooth communication with iOS devices. •