BayzoniJurusan Teknik Sipil Fakultas Teknik
Universitas Lampung, 2014
STRUKTUR BAJA II
Lantai Jembatan
(a) One Raffles Link, Singapore (b) Cellform beam
The main advantages ofcombining the use of steel and concrete materials for building construction are:
Steel and concrete may be arranged to produce an ideal combination of strength, with concrete efficient in compression and steel in tensionefficient in compression and steel in tension
Composite systems are lighter in weight (about 20 to 40% lighter than concrete construction). Because of their light weight, site erection and installation are easier, and thus labor costs can be minimized. Foundation costs can also be reduced.
The main advantages ofcombining the use of steel and concrete materials for building construction are: The construction time is reduced, since casting of additional floors may proceed
without having to wait for the previously cast floors to gain strength. The steel decking system provides positive moment reinforcement for the composite floor, requires only small amounts of reinforcement to control cracking, and provides fire resistance
The construction of composite floors does not require highly skilled labor. The steel decking acts as permanent formwork. Composite beams and slabs can accommodate raceways for electrification, communication, and air distribution systems. The slab serves as a ceiling surface to provide easy attachment of a suspended ceiling.
The composite slab, when fixed in place, can act as an effective in-plane diaphragm, which may provide effective lateral bracing to beams.
Concrete provides corrosion and thermal protection to steel at elevated temperatures. Composite slabs of a 2-h fire rating can be easily achieved for most building requirements.
The floor slab may be constructed by the following methods
Stress distribution in a composite cross section
Web opening with horizontal reinforcement
Composite castellated beams
Parallel composite beam system
Composite Trusses
Stub Girder System
KOMPONEN STRUKTUR KOMPOSIT(SNI)
Balok baja yang memikul pelat beton bertulang dan bekerja bersama-sama dengan pelat tersebut sebagai satu kesatuan dalam memikul lentur
Balok komposit sederhana atau menerus dengan Balok komposit sederhana atau menerus dengan penghubung geser; atau profil baja yang diberi selubung beton, baik yang dibangun dengan atautanpa penumpu sementara (perancah).
Komponen struktur lentur
Lebar efektif pelat lantai yang membentang pada masing-masing sisi dari sumbu balok tidak boleh melebihi:
a) Seperdelapan dari bentang balok (jarak a) Seperdelapan dari bentang balok (jarak antara tumpuan);
b) Setengah jarak bersih antara sumbu balok-balok yang bersebelahan;
c) Jarak ke tepi pelat.
Kekuatan balok komposit dengan penghubung geser
Persyaratan untuk dek baja bergelombang
Persyaratan untuk dek baja bergelombang
Penghubung geser
Gaya geser horizontal
Kekuatan penghubung geser jenis paku
Kekuatan penghubung geser kanal
Jumlah penghubung geser yang diperlukan
Jumlah penghubung geser yang diperlukan pada daerah yang dibatasi oleh titik-titik momen lentur maksimum, positif atau negatif, dan momen nol yang berdekatan adalah sama dengan gaya geserhorizontal total yang bekerjahorizontal total yang bekerja
Penempatan dan jarak antar penghubung geser
Kecuali ditentukan lain, penghubung geser yang diperlukan pada daerah yang dibatasi oleh titik-titik momen lentur maksimum dan momen nol yang berdekatan harus didistribusikan secara merata pada daerah tersebutpada daerah tersebut
The nominal strength of a shear stud connector embedded in a solid concrete slab may be computed from
When the shear connectors are embedded in concrete on a metal deck, a reduction factor R should be applied to Qn
When the ribs of the metal deck are perpendicular to the beam
When the ribs of the steel deck are parallel to the steel beam and wr/hr < 1.5,