FINAL SEWER BASIS OF DESIGN REPORT
Dixileta / Scottsdale NWC of Dixileta Drive and Scottsdale Road
Scottsdale, AZ 85266
Prepared For:
Desert Whisper, LLC 3018 N. 53rd Place
Phoenix, AZ 85018
858.212.5454
Prepared by:
Sustainability Engineering Group 8280 E. Gelding Drive
Scottsdale, AZ 85260
480.588.7226 www.azSEG.com
Project Number: 210218
Submittal Date: October 04, 2019
Revision Date: February 05, 2020
Revision Date: July 23, 2021
Case No.: 15-ZN-2019; 5-PP-2021 Plan Check No.: TBD
07/2
3/2
1
5-PP-20218/25/2021
FINAL Basis of DesignReport
9379 E San Salvador Dr.Scottsdale, AZ 85258
APPROVED
BY DATE
Disclaimer: If approved; the approval is granted under thecondition that the final construction documents submitted forcity review will match the information herein. Any subsequentchanges in the water or sewer design that materially impactdesign criteria or standards will require re-analysis,re-submittal, and approval of a revised basis of design reportprior to the plan review submission.; this approval is not aguarantee of construction document acceptance. For questions or clarifications contact the Water ResourcesPlanning and Engineering Department at 480-312-5685.
APPROVED AS NOTED
REVISE AND RESUBMIT
✔
rrahman 9/24/2021
09/24/2021
“LEED®ing and Developing Smart Projects”
Sewer Basis of Design Report Page i
Contents FINAL SEWER BASIS OF DESIGN REPORT ................................................................................................................... 1
1. INTRODUCTION .................................................................................................................................................. 1
1.1. SUMMARY OF PROPOSED DEVELOPMENT: ............................................................................................... 1
1.2. LEGAL DESCRIPTION: .................................................................................................................................. 1
2. DESIGN DOCUMENTATION ................................................................................................................................ 1
2.1. DESIGN COMPLIANCE: ............................................................................................................................... 1
3. EXISTING CONDITIONS ....................................................................................................................................... 1
3.1. EXISTING ZONING & LAND USE: ................................................................................................................. 1
3.2. EXISTING TOPOGRAPHY, VEGETATION AND LANDFORM FEATURES: ....................................................... 1
3.3. EXISTING UTILITIES: .................................................................................................................................... 2
3.4. FLOW MONITORING: ................................................................................................................................. 2
4. PROPOSED CONDITIONS .................................................................................................................................... 2
4.1. SITE PLAN: .................................................................................................................................................. 2
4.2. PROPOSED SEWER SYSTEM: ...................................................................................................................... 2
4.3. MAINTENANCE RESPONSIBILITIES: ............................................................................................................ 2
5. COMPUTATIONS ................................................................................................................................................ 3
5.1. SEWER DEMANDS: ..................................................................................................................................... 3
5.2. VARIANCE FROM STATED DESIGN FLOWS: ................................................................................................ 3
5.3. SEWER SYSTEM ANALYSIS: ......................................................................................................................... 3
6. SUMMARY .......................................................................................................................................................... 3
6.1. SUMMARY OF PROPOSED SEWER IMPROVEMENTS: ................................................................................ 3
6.2. PROJECT SCHEDULE: .................................................................................................................................. 3
7. REFERENCES ....................................................................................................................................................... 3
8. FIGURES .............................................................................................................................................................. 3
9. APPENDICIES ...................................................................................................................................................... 4
07/2
3/2
1
5-PP-20218/25/2021
“LEED®ing and Developing Smart Projects”
Preliminary Sewer Basis of Design Report Page 1
1. INTRODUCTION
1.1. SUMMARY OF PROPOSED DEVELOPMENT:
The report presents the service requirements of fourteen new single-family residential lots located on
17.5 acres of land located at the northwest corner of Scottsdale Road and Dixileta Drive. The purpose
of this report is to provide an analysis of the impact that this development will have on the city’s
wastewater system.
1.2. LEGAL DESCRIPTION:
The property is located in the Southeast quarter of Section 22, Township 5 North, Range 4 East of the
Gila and Salt River Base and Meridian, Maricopa County, Scottsdale, Arizona.
Refer to FIGURE 1 - Vicinity Map for the project’s location with respect to major cross streets.
2. DESIGN DOCUMENTATION
2.1. DESIGN COMPLIANCE:
The proposed sewer system is designed to meet requirements of the City of Scottsdale (“the City”)
Design Standards and Policies Manual (DS+PM), the Arizona Department of Environmental Quality
(“ADEQ”), and Maricopa County Environmental Services Department (“MCESD”).
2.2 PROCEDURES, POLICIES AND METHODOLOGIES:
The 18” sewer line in Scottsdale Road is evaluated in the City’s wastewater model for uses included in
the 2012 Water Reuse Master Plan Update, therefore, no sewer monitoring of this pipe is proposed.
Pipe flow, velocity and depths of the proposed sewer lines will be analyzed using Bentley FlowMaster®.
3. EXISTING CONDITIONS
3.1. EXISTING ZONING & LAND USE:
Land ownership includes approximately 17.5 acres of vacant land presently Zoned R1-70 ESL FO.
3.2. EXISTING TOPOGRAPHY, VEGETATION AND LANDFORM FEATURES:
The undeveloped site slopes to the southwest at 2% grade with thirty feet of fall across the site.
FIRM Map Number 04013C0895L dated October 16, 2013, indicates the northwest corner of the site
lies in designated Zone “AO” with a 1-foot depth and 3 fps velocity . That portion of the site with
proposed lots lies outside the designated flood plain. Refer to FIGURE 2 for an aerial of the overall
project existing conditions and FIGURE 3 for the FIRM Map.
5-PP-20218/25/2021
“LEED®ing and Developing Smart Projects”
Preliminary Sewer Basis of Design Report Page 2
3.3. EXISTING UTILITIES:
Sewer: City of Scottsdale (QS 53-44) - see FIGURE 4.
• An existing 18” VCP sewer line is located in Scottsdale Road within the northbound travel lanes.
• No sewer lines exist in Dixileta Drive or sewer services/stubs to the site.
3.4. FLOW MONITORING:
Flow monitoring of the 18” sewer line in Scottsdale Road is not necessary as this is a trunk line included
in the City’s master plan and sewer model. The City will verify capacity for this project.
4. PROPOSED CONDITIONS
4.1. SITE PLAN:
Proposed development consists of 14 single-family residential lots with access off a proposed cul-de-
sac extended north from Dixileta Drive. The property is requesting rezoning to R1-43 ESL FO.
4.2. PROPOSED SEWER SYSTEM:
A sewer cannot be extended along Dixileta Drive to serve this project because the topography drops off
to the west quickly and cover is not adequate over the sewer, reaching as little as 2 ft. A new manhole
will be constructed to connect to the public system per M.A.G. 440-3, over the existing 18” VCP north
of the Dixileta Drive intersection and extended into the site within a tract between lots 13 and 14.
Approximately 750-feet of 8” sewer pipe will be extended west and north in the cul-de-sac providing
sewer service to the 14 lots. Lots (1&14) near the southern end of the site may require individual on-
site ejector systems as building finish floors dictate. Any necessary ejector lines will be privately
owned, operated and maintained by the property owner and constructed within private easements.
Manholes receiving ejected wastewater will be lined. Lots with building pads lower than the next
upstream manhole will require backwater valves per DS+PM Sec. 7-1.409 G.
Topography prohibits extension of onsite sewer to the 71st Street alignment between Lots 3 and 4. See
APPENDIX I for the Preliminary Utility Plan.
4.3. MAINTENANCE RESPONSIBILITIES:
The on-site sewer main will be public and located in an easement/tract or right-of-way dedicated to the
City of Scottsdale. Therefore, the on-site and off-site sewer system will be public and maintained by the
City. As previously stated, any required ejector lines will be owned, operated and maintained by the
respective property owner and placed within private easements outside of any right-of-way or public
utility easement.
5-PP-20218/25/2021
Final Plat map to have description ofdedicated W&S Easement.Dimension label itself will not sufficeper DSPM Section 7-1.501.P .
OK
“LEED®ing and Developing Smart Projects”
Preliminary Sewer Basis of Design Report Page 3
5. COMPUTATIONS
5.1. SEWER DEMANDS:
The proposed daily demands are shown in TABLE 1 below. Average day sewer demands are described
in Section 7-1.403 of the City of Scottsdale’s Design Standards & Policies Manual.
Table 1 - SEWER DEMAND CALCULATIONS
Units Avg. Day Demand (GPCPD)
Persons per Unit
Avg. Day Demand
(GPD/GPM)
Peaking Factor
Peak Flow (GPD/GPM)
14 100 2.5 3500/2.43 4 14,000/9.72
5.2. VARIANCE FROM STATED DESIGN FLOWS:
No variance from the applicable design criteria is being requested.
5.3. SEWER SYSTEM ANALYSIS:
The proposed 8” pipe has adequate capacity to provide service to the 14 lots. A few of the southern
lots may need to provide onsite ejector systems to discharge up to the gravity line in the cul-de-sac.
The feasibility of extending the sewer west to 71st Street between lots 3 and 4 resulted in inadequate
cover (less than 2 feet).
Reference APPENDIX II for the pipe hydraulics and APPENDIX III for a sample ejector spec..
6. SUMMARY
6.1. SUMMARY OF PROPOSED SEWER IMPROVEMENTS:
The proposed sewer extension will be adequate for providing service to this subdivision. Topography
does not permit any extension further west or north to accommodate adjacent properties.
6.2. PROJECT SCHEDULE:
The infrastructure and building pads are proposed to be constructed in a single phase.
7. REFERENCES 1. COS Sewer QS 53-44
2. City of Scottsdale Design Standards & Policies Manual, 2018 (Chapter7 – Sewer)
8. FIGURES 1. Vicinity Map
2. Aerial Map
3. FIRM Map
4. COS QS Map 53-44
5-PP-20218/25/2021
“LEED®ing and Developing Smart Projects”
Preliminary Sewer Basis of Design Report Page 4
9. APPENDICIES I. Preliminary Utility Plan
II. Pipe Hydraulics
III. Duplex Ejector Sample Spec
5-PP-20218/25/2021
“LEED®ing and Developing Smart Projects”
8280 E. Gelding Dr., Suite 101 Scottsdale, AZ 85260
Sustainability Engineering Group [email protected] 480.588.7226 www.azSEG.com
FIGURES 1 -Vicinity Map
2 – Aerial map
3 – FIRM Map
4 – COS Q-S Map
5-PP-20218/25/2021
“LEED®ing and Developing Smart Projects”
Sewer Capacity Report FIGURE 1 – Vicinity Map
SITE
5-PP-20218/25/2021
“LEED®ing and Developing Smart Projects”
Sewer Capacity Report FIGURE 2 - Aerial
5-PP-20218/25/2021
“LEED®ing and Developing Smart Projects”
8280 E. Gelding Dr., Suite 101 Scottsdale, AZ 85260
Sustainability Engineering Group [email protected] 480.588.7226 www.azSEG.com
FIGURE 3 – Excerpt from
FIRM Map No 04013C0895L
5-PP-20218/25/2021
TROVIA
(277-16)
PARCEL "A"
AT BELLASERA
MCR: (1458-32)
A REPLAT OF LOTS 1, 5, 12, 18, 19 AND 23,
VILLAGE
AT IRON MOUNTAIN
MCR: (1340-43)
(588-11)
SCOTTSDALE
HIGHLANDS
(685-18)
D.E.
16' D.E.
D.E.
C.H.P.
1' V .N.E.
W.D.
NOTICE OF R ELEAS E
NOTICE OF R ELEAS E
I.L.-AP./C.O.S .
I.L.-AP./C.O.S.
D. & F.C.E.
D.E.
C.H.P.
R .O.E.
R .O.E.
C.H.P.
PV T. IMP. IN R /W
D.E.
C/C C/CC/CC/C
D.E.
W.L.E.
D.E.
W .L.E.
D.E.
10' D.E.
W .D.
W .D.
W.D.
R ELEAS E OF C.H.P.
R ELEAS E OF C.H.P.
R ELEAS E OF C.H.P.
R ELEAS E OF C.H.P.
R ELEAS E OF C.H.P.
1' V.N.E.
100'V .C.E.
140'S .C.E.
D.E.
1' V.N.E.
8' P.U.E.
100'S .C.E.
100'S .C.E.
1' V.N.E.
1' V.N.E.
15' P.TL. E.
15' P.TL.E.
S.C.E.
S.C.E.
A/CH
S.C.E.
1' V .N.E. 1' V .N.E. 1' V .N.E.25' EQ . E. 25' EQ . E. 25' EQ . E. 25' EQ . E.
25' EQ . E.1' V .N.E.
83/50651884/361365 84/36136488/304717
86/689819
95/065464
95/065464
92/550973
92/380123
87/161338
87/161338
87/161346
95/018241
95/018241
87/084645
87/084645
89/483249 90/124615
88/106755
88/106755
86/217064
94/524142, 94/693478
95/096755
95/077734
95/096756
95/421739
95/421739
97/091507
86/217064
97/910047
97/910047
98/441669
98/441669
99/482725
99/482725
99/846416
99/922018
99/922020
88/062516
91/491162-4
95/312784
95/312784
95/282013
00/483890
00/483891
00/640818
00/873077
01/046496
01/046496
01/747229
01/747228
01/1069245
95/018248
03/924211
2922/494
2781/119
3116/428
3018/130
2929/131
2929/131
2929/131
CTY. RD. MAP 13/18
CTY. RD. MAP 13/18
CTY. RD. MAP 13/18
CTY. RD. MAP13/18
04/1449085
05/615252 05/61525205/61525205/615252
05/883835
05/971973
05/971973
05/1617115
05/1617038
05/1617106
06/657276
06/948266
06/948313
06/1604118
95/312785
3018/143
10/0108531
98/503027 & 10/0108531
98/503027, 10/0108531 & 00/483891
13/589799
13/589799
13/589799
13/589799
13/589799
97/059349
84/272041
6858/505 6858/505
D.& F.C.E.
D.&F.C.E.
25' W.L.E. N.A.O.S .
N.A.O.S .
15/0710751
15/0727502
15/0727506
15/0727506
15/0727503
15/0727503
R .O.E.15/0885083
N.A.O.S .05/0971966
N.A.O.S .15/0885082
W.L.E.06/0948308
00/0968847
00/0968847
00/0968847
00/0968847
00/0968847
8' ACC.E.00/0968847
8' ACC.E.
00/0968847
N.A.O.S .16/0521368
N.A.O.S.
16/0709539
D.&F.C.E.16/0712723
R .O.E.16/0746507
16/0782394
*
N.A.O.S .
*
N.A.O.S .
N.A.O.S .17/0084154D.&F.C.E.
17/0084099
D.&F.C.E.17/0090734
N.A.O.S .17/0090739
D.&F.C.E.17/0120802
N.A.O.S .17/0120502
N.A.O.S .13/0711440
92/0401841
92/0401841
D.&F.C.E.
N.A.O.S .
17/0656480
N.A.O.S.
N.A.O.S .N.A.O.S .18/0237260
18/0252239
08/0401114
50' S.C.E.08/0401102
P.U.E.08/0401117
D.&F.C.E.08/0488441
N.A.O.S .08/0401109
*1' V.N.E.08/0401115
08/0401114
R .O.E.18/0756589
N.A.O.S .18/0756560
N.A.O.S .
N.A.O.S .00/0711553
N.A.O.S .00/0711553
D.&F.C.E.09/1193770
N.A.O.S.
00/0873078
N.A.O.S.
N.A.O.S.
00/0873078
00/0873078
N.A.O.S .99/0536827
N.A.O.S.07/1335731
N.A.O.S . N.A.O.S.
N.A.O.S .
98/0056571
98/0056571
98/0056571
N.A.O.S .98/0699538
216-67-025A
216-67-039B
216-67-043B
216-67-044A
216-67-045B
216-67-250B
216-67-093B
216-67-031 216-67-231 216-67-119A
216-67-069 216-67-070216-67-066 216-67-121216-67-230
216-67-086
216-67-234
216-67-120
216-67-052
216-67-239
216-67-058
216-67-124
216-67-248
216-67-117
216-67-114
216-67-113216-67-061
216-67-027
216-67-068B216-67-115A
216-67-032A216-67-032B
216-67-085A
216-67-085B216-67-128216-67-057216-67-030B216-67-030C
216-67-122A 216-67-122B
216-67-123A
216-67-089A
216-67-089B
216-67-126E 216-67-126D216-67-129A216-67-229A 216-67-229B
216-67-254 216-67-235A 216-67-235B
216-67-076A
216-67-076B
216-67-112A
216-67-112B
216-67-087A 216-67-087B216-67-118A
216-67-116A
216-67-046A
216-67-088A 216-67-088B216-67-251A
216-67-028A
216-67-056A
216-67-130A
TR ACT"A"
TR ACT"H"
130(7125)125
216-67-125A
(6805)216-67-026
(6898)
(30003)
216-67-240
216-67-050
216-67-238
(6885)216-67-249
(6800) 216-67-247D216-67-111A
216-67-100B
(6820)216-67-074
(30084)
(7027)216-67-116B
216-67-029A
(6939)216-67-123B (7015)
(6738)
(6740)
(6745)
(7010)
(6990)(7150)
(7101)
(29836)
(6950)(7024) (7058)
(7176)
(6811)
(6810)
(6880)
(29950)
(6999)
(7040)
(7125)
(30013)
(30232)
(29838)
(6940)
(7035)
(30120)
(6940)
(6931)(6945)(6869)
(30010)
(30220)
(7171)
(7012)
(30000)
(6910)
(7191)
(30221)
(6915) (30400)
(7120)
(6925)
(29995)
(7023) (7051) (7085)
(6960)
(7035)
(6802)
(7015)
(7152)
(7030)
(7175)(7036)
STREET
NORTH
70TH
STREET
NORTH
71ST
SCOTTSDALE
EAS T BAR W ICK DR IV E
EAS T MONTGOMER Y R OAD
NORTH
ROAD
NOR TH
SCOTTSDALE
R OAD
NORTH
69TH
STREET
EAS T BAKER DR IV E
EAS T DAV IS R OAD
NORTH
68TH
STREET
EAS T DAV IS R OAD
EAS T W INDS TONE TR AIL
EAS T DIX ILETA DR IV E
1 11 1
1 1
1 11 1
1 11 1
1 11 1
1 11 1
1 11 1
1 11 1
1 11 1
1 11 1
1 11 1
1111
1111
11
11
11
1 11 1
1 11 1
1 11 1
1 11 1
1 11 1
1 11 1
1 11 1
1 11 1
1 11 1
11
11
1 11 1
1 11 1
1 11 1
1 11 1
1 11 1
1 11 1
1 11 1
1 11 1
1 11 1
1 1
1111111111
1 11 1
1 11 1
1 11 1
1 11 1
1 11 1
1 11 1
1 11 1
1 11 1
11
1 11 1
1 11 1
1 11 1
1 11 1
1 11 1
1 11 1
1 11 1
1 11 1
1 11 1
1 11 1
1 11 1
1 11 1
11
"
"
!
!SS(
!SS(
!SS(
!SS(
!SS(
!SS(
!SS(
!SS(
!SS(
*
N.F.N.F.
*
2179.536+51
*
2192.580+75
*
N.F.2181.34
*
N.F.N.F.
*
N.F.N.F.
*
N.F.N.F.
M.H. TAP
*
2158.582148.66
*
2189.906+75
*
2194.452+90
* 2195.203+53
*
N.F.2191.81W
*
N.F.N.F.
*
2179.030+46
*
N.F.N.F.
*
2172.265+69
*
N.F.N.F.
*
2159.896+56
*
2161.811+04
*
2162.640+21
8''PV C
18''VCP
18''VCP
18''VCP
18''TYPUNK
18'' VCP
Q UAR TER S ECTION MAP
S E 1/4 S EC. 22 T5N R 4E
53-43
53-45
52-44
54-44
07-JU
L-19
SEWERSEWER
53-4453-44
THIS DOCUMENT IS PROVIDED FOR GENERAL INFORMATION PURPOSES ONLY. THE CITY OF
SCOTTSDALE DOES NOT WARRANT ITS ACCURACY, COMPLETENESS OR SUITABILITY FOR ANY
PARTICULAR PURPOSE. IT SHOULD NOT BE RELIED UPON WITHOUT FIELD VERIFICATION.
NO
TI
CE
THE C
ITY O
F SCO
TTSD
ALE
The map scale of 1" = 100' is basedon a full size print of 30" x 36"
S CALE: 1" = 100'
0 100 20050
NORTH
• THIS IS A COMPUTER GENER ATED DR AW ING. FOR ANY R EV IS IONS PLEAS E CONTACT THE CITY OF S COTTS DALE GIS DEPAR TMENT AT (480) 312-7792.• THE S ECTION L INE BEAR ING AND DIS TANCES AR E BAS ED ON THE CITY OF S COTTS DALE GPS S UR V EY OF S EPTEMBER , 1991. BEAR INGS AR E NAD 83 GR ID AND DIS TANCES AR E FLATTENED TO GR OUND. W HER E NO COR NER W AS FOUND THE DIMENS IONS AR E GIV EN TO CALCULATED S ECTION COR NER S AND AR E NOTED AS 'CALCULATED' ON THE MAP.
GENERAL NOTES:
S 1/4 COR .
MONTGOMER Y R OAD
DIX IL ETA DR IV E
V ICINITY MAPE 1/4 COR .
S E COR .
68TH STREET
SCOTTSDALE ROAD
CENTER — — 30600 N
— — 29800 N— —
— —
————6800 E ——
7200 E ——
3629 North Drinkwater BoulevardS cottsdale, Arizona 85251
SC OTT SDALE GE OGRAP HICINFOR MATION SYSTE MS
LEGEND:!
PlugS ewer S ervice Point
,
S ewer V alveS ewer Tap Point
Manhole
S ewer Main - Force
Non-GPS Point
CleanoutL ift S tation
S ewer Main - Private
Treatment PlantS ewer Main - Gravity
"SLS)
!SS(
&
"
!
D!Ó(
11 11
Force
11 11
Figure 4
SITE
5-PP-20218/25/2021
“LEED®ing and Developing Smart Projects”
8280 E. Gelding Dr., Suite 101 Scottsdale, AZ 85260
Sustainability Engineering Group [email protected] 480.588.7226 www.azSEG.com
APPENDICIES
I – Preliminary Utility Plan
II – Pipe Hydraulics
III - Duplex Ejector Sample Spec
5-PP-20218/25/2021
E DI
XILE
TA D
R
WIN
STO
NE T
RAIL
N 71st ST
N SCOTTSDALE RD
SUST
AINAB
ILITY
ENGI
NEER
ING
GROU
P
190708
MA
07/16/2021
PRELIMINARY PLAT
THIS DR
AWING
IS AN INST
RUME
NT OF
SERVICE
AND TH
E PROP
ERTY O
F SUSTA
INABILIT
Y ENGIN
EERING
GROU
P, AND SH
ALL REM
AIN THE
IR PROP
ERTY. TH
E USE O
F THIS DR
AWING
SHALL B
E RESTR
ICTED TO
THE OR
IGINAL S
ITE FOR
WHIC
H IT IS PRE
PARED A
ND PU
BLICATIO
N THERE
OF IS EX
PRESSLY
LIMITED
TO SUC
H USE.
8280
E. G
ELD
ING
DR
IVE
SUIT
E 10
1, S
CO
TTSD
ALE,
AR
IZO
NA
8526
0
WW
W. A
ZSEG
.CO
M
TEL.
480
.588
.722
6
FAX
480
.259
.353
4
07/16/2021MA
AF
SCAF
PRELIMINARYNOT FOR
CONSTRUCTION
PRELIMINARYNOT FOR
CONSTRUCTION
07/16/202107/16/202107/16/202107/16/2021
WATER KEYNOTES: SEWER KEYNOTES:
BASIS OF BEARING: BENCHMARK: CIVIL ENGINEER OWNER
VICINITY MAP
SITE
E WINDSTONE TR.
SCOTTSDALE AND DIXILETA
PROPOSED LEGEND:
UTILITY NOTES
E DIXILETA DRIVE
E LONE MOUNTAIN ROAD
N 64
TH S
TREE
T
N SC
OTTS
DALE
ROA
D
5-PP-20218/25/2021
Add a manhole. This willallow future connection ofejector sewer from the west.
Water and Sewer Easement
“LEED®ing and Developing Smart Projects”
8280 E. Gelding Dr., Suite 101 Scottsdale, AZ 85260
Sustainability Engineering Group [email protected] 480.588.7226 www.azSEG.com
APP ENDIX II Pipe Hydraulics
5-PP-20218/25/2021
PRESSURE SEWERSYSTEMS
Sewer Anywhere and SaveE/One Sewer Systems give engineers, builders, developers, municipal sanitarians and land planners unprecedented new freedom in land usage and sewer rehabilitation.
Easy to install. Easy to operate. And easy to maintain.
The sensible sewering solution that defies gravity and saves up to 50% – the E/One sewer system.
Environmentally sensitive. Economically sensible.™
E/One, Extreme, Engineered to do One Job Perfectly and Environmentally Sensitive Economically Sensible are trademarks for Environment One Corporation. Copyright 2016 Environment One Corporation. All rights reserved throughout the world.
NOBODY CAN TOUCH OUR CURVE.In a low pressure system, constant, predictable pump output is the foundation for proper hydraulic design. It enables the engineer to minimize retention time, pump wear, and keep scouring velocity at effective levels.
Environment One’s semi-positive displacement, progressing cavity pump has a nearly vertical H-Q curve. It is by far the most “forgiving” pump design – providing predictable flow over the full range of typical system pressures; strengths critical in a large-scale, low pressure sewer system.
E/One’s superior high head capability allows a system with few, if any, lift stations. And, it easily accommodates additional future connections without compromising system performance.
These E/One pump characteristics translate into:
• predictable hydraulic design
• lower collection system capital costs
• less maintenance
• lower operating costs
Environment One Corporation2773 Balltown RoadNiskayuna, NY USA 12309-1090Voice (01) 518.346.6161Fax 518.346.6188www.eone.com
A Precision Castparts CompanyLM000365 Rev D
High Heads/Negative Heads. Industry’s most reliable operation – rated for continuous duty of negative head to total dynamic head of 185 feet reduces the number of lift stations and pipe sizes. This cuts costs – both initially and in long-term operation and maintenance.
Constant Flow. The system pressures to be overcome by any given grinder pump in a low pressure system vary dramatically over the course of a day. E/One’s progressing cavity pump readily accommodates these pressure variations while maintaining a nearly constant flow without ever operating at “near shut off” – thus avoiding the wear and motor burn-out suffered by other pump types.
High Grinding Torque. Our unique pump system, driven by a one-horsepower motor turning at 1725 rpm, produces grinding torque greater than a larger horsepower pump turning at twice the speed.
Energy Efficient. The pump is activated automatically and runs for short periods.
Low Maintenance Submersible Motor.Low maintenance and long life are the hallmarks of our air-filled motor. Permanently lubricated ball bearings and Class F insulation eliminate the need for periodic oil changes and oil disposal costs required by oil-filled submersible motors.
Large-Diameter Grinder Assembly. Almost twice the diameter of most other types of grinder pumps, contributing to a dramatic reduction of inflow velocity for less wear and no blinding, clogging or jamming.
No Preventive Maintenance. Non-fouling static level sensors require no preventive maintenance. Because of our unique, near constant discharge rate, no main line flushing is required in a properly designed system.
Corrosion Resistance. Corrosion resistance is built into the E/One® design.
Serviceability. Our unique core design eliminates the need for in-field troubleshooting and pump servicing. This means lower maintenance costs and minimum homeowner inconvenience.
SOME KEY ADVANTAGES:
CONSULT FACTORYFOR INTERMITTENTUSE ABOVE 80 PSIOR 185 FEET TDH
LOW PRESSURE SYSTEM DESIGN PRESSURE
E/One Product Family
APPENDIX III5-PP-20218/25/2021
ENGINEERED TO DO ONE JOB PERFECTLY.™
At the heart of the E/One Sewer System is the toughest, hardest working pump in the industry. The new standard in excellence, durability, and longevity, the E/One Extreme Series Grinder Pump. Its evolution refl ects everything we’ve learned in more than 40 years as the originator and leader in the category of low pressure sewer systems.
The pump stations incorporate the grinder pump, motor controls and level sensing device integrated into a compact unit, easily removable for servicing when necessary.
And, the geometry of the pump not only produces a near-vertical pump curve, it also allows passage of ground solids without clogging. Because of the low rpm and highest quality components, we experience the lowest service call rate in the industry. An average mean time of 10 years between service calls is typical.
The W-Series is E/One’s most versatile grinder pump station – a range of basins, covers, discharges, inlets and panels are available. Simplex through quadriplex stations work with single homes, light commercial applications, or several homes.
The W-Series allows you to choose integral components for optimal installation and performance for your site’s conditions. Whatever tank size is needed, many features from discharge configuration to panel options can be adjusted to your specific needs. W-Series stations can have one pump or up to four pumps, depending on the tank chosen.
Simplex Stations
• HDPE or fi berglass (not shown) construction
• Station capacities of 100, 237 and 476 gallons available
• Various station heights available
Multiple-Pump Stations
• HDPE construction
• Station capacities of 476 and 486 gallons available
• 476-gallon tank allows for 1 or 2 pumps
• 486-gallon tank allows for 2, 3 or 4 pumps
• Various station heights available
The W-Series fi berglass tanks offer a multitude of station volumes and heights with diameters from 24 inches to 72 inches, and heights from 60 inches to 240 inches.
* Please visit www.eone.com for application and fl ow information
The E/One D-Series features a wetwell/
drywell design that provides a dry accessway
for ease of service. Plus a modular design
and one-piece core that permits simple
core replacement – should it ever become
necessary. Available in both simplex and
duplex grinder pump stations to fi t a wide
variety of applications, from single-family
homes to light commercial applications to
several homes in conjunction.
The tanks are made from tough, corrosion-
resistant HDPE for long life and zero upkeep.
Station capacities of 70 gallons to 500 gallons
are available.
THE W-SERIESEngineered for choice.
More builders and municipalities are opting for the ease and convenience of the E/One Indoor Unit, which offers easy access along with all the benefits of the D-Series. An attractive self-contained unit, the I-Series fits unobtrusively into a basement or garage with a clean, contemporary design that feels right at home with other major appliances.
It can be used as part of a new E/One sewer system or retrofit into an existing low pressure or gravity sewer system.
With its quiet, energy-efficient pump and sound insulating properties, the I-Series is easy to live with.
THE D-SERIESWetwell/Drywell for Superior
Serviceability
THE I-SERIES INDOOR UNITSelf-Contained for Indoor Installation
DESIGN
• Enhanced pump controls: expanded diagnostics, protection, and communications capabilities
• “Core” concept with integral level and motor controls
• Radial O-ring seals on all joints
• Thermally welded discharge assembly for high-pressure performance
• Differential pressure switch level control in separate, removable assembly
• Equalizer compensates for fl uctuations in atmospheric pressure while providing a sealed, water-tight level control system
• Integral check valve and anti-siphon valve assembly
• New, more resilient stator material enables higher pressure rating of 80 psi, using E/One proprietary stator chemistry
• All fasteners and hardware are 300 series stainless steel
RELIABILITY
• Huge double O-rings used for casting joint seals
• Casting joints designed for corrosive environment
• Indestructible level sensor housing
• Ultrasonically welded check valve assembly
• Superior corrosion protection – wet-applied coating on Class 30 cast iron vs. industry-standard powder coating
• Weld-free stainless steel stand
The Most Rugged, Longest-Lasting
Grinder Pump in the Industry
The progressing cavity pump itself is based on the Moineau principle. A rotor turns within a stator, creating a sequence of sealed chambers. The precision-cast and polished stainless steel rotor moves wastewater through these chambers at a nearly constant fl ow, over a wide range of conditions – from negative to abnormally high heads. Turning at just 1,725 rpm, the one-horsepower motor can pump fluid through more than two miles of small-diameter piping or elevation changes of over 185 feet.
PERFORMANCE
• Design pressures to 80 psi (185 feet total dynamic head)
• Progressing cavity pump provides predictable fl ow over varying system pressure
• 1 hp, 1725 rpm, air-cooled motor provides low speed, high torque operation, eliminating jams
• Field-proven, large-diameter grinding mechanism provides low inlet velocity, eliminating pump blinding or clogging
• Integral check valve protects against system back pressure; anti-siphon valve facilitates downhill pumping applications
SERVICEABILITY
• No preventive maintenance required
• Quick-release core latch on D-Series – no mounting bolts required
• Electrical quick disconnect (EQD) seals and connects without tools; uses single turn locking ring
• Detachable level sensor assem-bly; wireless design available using inductive coupling
• Discharge plumbing quickly disconnects from grade level
• Backward compatibility to earlier generations/designs
• Air-fi lled motor more effi cient than oil-fi lled motors and eliminates need to change and dispose of oil
• One pump for all series
• Backward-compatible EQD
237 gal
100 gal
476 gal
486 gal
99471_EOneSewerSystems.indd 299471_EOneSewerSystems.indd 2 9/22/16 9:50 AM9/22/16 9:50 AM
5-PP-20218/25/2021
PRESSURE SEWERSYSTEMS
Sewer Anywhere and SaveE/One Sewer Systems give engineers, builders, developers, municipal sanitarians and land planners unprecedented new freedom in land usage and sewer rehabilitation.
Easy to install. Easy to operate. And easy to maintain.
The sensible sewering solution that defies gravity and saves up to 50% – the E/One sewer system.
Environmentally sensitive. Economically sensible.™
E/One, Extreme, Engineered to do One Job Perfectly and Environmentally Sensitive Economically Sensible are trademarks for Environment One Corporation. Copyright 2016 Environment One Corporation. All rights reserved throughout the world.
NOBODY CAN TOUCH OUR CURVE.In a low pressure system, constant, predictable pump output is the foundation for proper hydraulic design. It enables the engineer to minimize retention time, pump wear, and keep scouring velocity at effective levels.
Environment One’s semi-positive displacement, progressing cavity pump has a nearly vertical H-Q curve. It is by far the most “forgiving” pump design – providing predictable flow over the full range of typical system pressures; strengths critical in a large-scale, low pressure sewer system.
E/One’s superior high head capability allows a system with few, if any, lift stations. And, it easily accommodates additional future connections without compromising system performance.
These E/One pump characteristics translate into:
• predictable hydraulic design
• lower collection system capital costs
• less maintenance
• lower operating costs
Environment One Corporation2773 Balltown RoadNiskayuna, NY USA 12309-1090Voice (01) 518.346.6161Fax 518.346.6188www.eone.com
A Precision Castparts CompanyLM000365 Rev D
High Heads/Negative Heads. Industry’s most reliable operation – rated for continuous duty of negative head to total dynamic head of 185 feet reduces the number of lift stations and pipe sizes. This cuts costs – both initially and in long-term operation and maintenance.
Constant Flow. The system pressures to be overcome by any given grinder pump in a low pressure system vary dramatically over the course of a day. E/One’s progressing cavity pump readily accommodates these pressure variations while maintaining a nearly constant flow without ever operating at “near shut off” – thus avoiding the wear and motor burn-out suffered by other pump types.
High Grinding Torque. Our unique pump system, driven by a one-horsepower motor turning at 1725 rpm, produces grinding torque greater than a larger horsepower pump turning at twice the speed.
Energy Efficient. The pump is activated automatically and runs for short periods.
Low Maintenance Submersible Motor.Low maintenance and long life are the hallmarks of our air-filled motor. Permanently lubricated ball bearings and Class F insulation eliminate the need for periodic oil changes and oil disposal costs required by oil-filled submersible motors.
Large-Diameter Grinder Assembly. Almost twice the diameter of most other types of grinder pumps, contributing to a dramatic reduction of inflow velocity for less wear and no blinding, clogging or jamming.
No Preventive Maintenance. Non-fouling static level sensors require no preventive maintenance. Because of our unique, near constant discharge rate, no main line flushing is required in a properly designed system.
Corrosion Resistance. Corrosion resistance is built into the E/One® design.
Serviceability. Our unique core design eliminates the need for in-field troubleshooting and pump servicing. This means lower maintenance costs and minimum homeowner inconvenience.
SOME KEY ADVANTAGES:
CONSULT FACTORYFOR INTERMITTENTUSE ABOVE 80 PSIOR 185 FEET TDH
LOW PRESSURE SYSTEM DESIGN PRESSURE
E/One Product Family
5-PP-20218/25/2021
ENGINEERED TO DO ONE JOB PERFECTLY.™
At the heart of the E/One Sewer System is the toughest, hardest working pump in the industry. The new standard in excellence, durability, and longevity, the E/One Extreme Series Grinder Pump. Its evolution refl ects everything we’ve learned in more than 40 years as the originator and leader in the category of low pressure sewer systems.
The pump stations incorporate the grinder pump, motor controls and level sensing device integrated into a compact unit, easily removable for servicing when necessary.
And, the geometry of the pump not only produces a near-vertical pump curve, it also allows passage of ground solids without clogging. Because of the low rpm and highest quality components, we experience the lowest service call rate in the industry. An average mean time of 10 years between service calls is typical.
The W-Series is E/One’s most versatile grinder pump station – a range of basins, covers, discharges, inlets and panels are available. Simplex through quadriplex stations work with single homes, light commercial applications, or several homes.
The W-Series allows you to choose integral components for optimal installation and performance for your site’s conditions. Whatever tank size is needed, many features from discharge configuration to panel options can be adjusted to your specific needs. W-Series stations can have one pump or up to four pumps, depending on the tank chosen.
Simplex Stations
• HDPE or fi berglass (not shown) construction
• Station capacities of 100, 237 and 476 gallons available
• Various station heights available
Multiple-Pump Stations
• HDPE construction
• Station capacities of 476 and 486 gallons available
• 476-gallon tank allows for 1 or 2 pumps
• 486-gallon tank allows for 2, 3 or 4 pumps
• Various station heights available
The W-Series fi berglass tanks offer a multitude of station volumes and heights with diameters from 24 inches to 72 inches, and heights from 60 inches to 240 inches.
* Please visit www.eone.com for application and fl ow information
The E/One D-Series features a wetwell/
drywell design that provides a dry accessway
for ease of service. Plus a modular design
and one-piece core that permits simple
core replacement – should it ever become
necessary. Available in both simplex and
duplex grinder pump stations to fi t a wide
variety of applications, from single-family
homes to light commercial applications to
several homes in conjunction.
The tanks are made from tough, corrosion-
resistant HDPE for long life and zero upkeep.
Station capacities of 70 gallons to 500 gallons
are available.
THE W-SERIESEngineered for choice.
More builders and municipalities are opting for the ease and convenience of the E/One Indoor Unit, which offers easy access along with all the benefits of the D-Series. An attractive self-contained unit, the I-Series fits unobtrusively into a basement or garage with a clean, contemporary design that feels right at home with other major appliances.
It can be used as part of a new E/One sewer system or retrofit into an existing low pressure or gravity sewer system.
With its quiet, energy-efficient pump and sound insulating properties, the I-Series is easy to live with.
THE D-SERIESWetwell/Drywell for Superior
Serviceability
THE I-SERIES INDOOR UNITSelf-Contained for Indoor Installation
DESIGN
• Enhanced pump controls: expanded diagnostics, protection, and communications capabilities
• “Core” concept with integral level and motor controls
• Radial O-ring seals on all joints
• Thermally welded discharge assembly for high-pressure performance
• Differential pressure switch level control in separate, removable assembly
• Equalizer compensates for fl uctuations in atmospheric pressure while providing a sealed, water-tight level control system
• Integral check valve and anti-siphon valve assembly
• New, more resilient stator material enables higher pressure rating of 80 psi, using E/One proprietary stator chemistry
• All fasteners and hardware are 300 series stainless steel
RELIABILITY
• Huge double O-rings used for casting joint seals
• Casting joints designed for corrosive environment
• Indestructible level sensor housing
• Ultrasonically welded check valve assembly
• Superior corrosion protection – wet-applied coating on Class 30 cast iron vs. industry-standard powder coating
• Weld-free stainless steel stand
The Most Rugged, Longest-Lasting
Grinder Pump in the Industry
The progressing cavity pump itself is based on the Moineau principle. A rotor turns within a stator, creating a sequence of sealed chambers. The precision-cast and polished stainless steel rotor moves wastewater through these chambers at a nearly constant fl ow, over a wide range of conditions – from negative to abnormally high heads. Turning at just 1,725 rpm, the one-horsepower motor can pump fluid through more than two miles of small-diameter piping or elevation changes of over 185 feet.
PERFORMANCE
• Design pressures to 80 psi (185 feet total dynamic head)
• Progressing cavity pump provides predictable fl ow over varying system pressure
• 1 hp, 1725 rpm, air-cooled motor provides low speed, high torque operation, eliminating jams
• Field-proven, large-diameter grinding mechanism provides low inlet velocity, eliminating pump blinding or clogging
• Integral check valve protects against system back pressure; anti-siphon valve facilitates downhill pumping applications
SERVICEABILITY
• No preventive maintenance required
• Quick-release core latch on D-Series – no mounting bolts required
• Electrical quick disconnect (EQD) seals and connects without tools; uses single turn locking ring
• Detachable level sensor assem-bly; wireless design available using inductive coupling
• Discharge plumbing quickly disconnects from grade level
• Backward compatibility to earlier generations/designs
• Air-fi lled motor more effi cient than oil-fi lled motors and eliminates need to change and dispose of oil
• One pump for all series
• Backward-compatible EQD
237 gal
100 gal
476 gal
486 gal
99471_EOneSewerSystems.indd 299471_EOneSewerSystems.indd 2 9/22/16 9:50 AM9/22/16 9:50 AM
5-PP-20218/25/2021
ENGINEERED TO DO ONE JOB PERFECTLY.™
At the heart of the E/One Sewer System is the toughest, hardest working pump in the industry. The new standard in excellence, durability, and longevity, the E/One Extreme Series Grinder Pump. Its evolution refl ects everything we’ve learned in more than 40 years as the originator and leader in the category of low pressure sewer systems.
The pump stations incorporate the grinder pump, motor controls and level sensing device integrated into a compact unit, easily removable for servicing when necessary.
And, the geometry of the pump not only produces a near-vertical pump curve, it also allows passage of ground solids without clogging. Because of the low rpm and highest quality components, we experience the lowest service call rate in the industry. An average mean time of 10 years between service calls is typical.
The W-Series is E/One’s most versatile grinder pump station – a range of basins, covers, discharges, inlets and panels are available. Simplex through quadriplex stations work with single homes, light commercial applications, or several homes.
The W-Series allows you to choose integral components for optimal installation and performance for your site’s conditions. Whatever tank size is needed, many features from discharge configuration to panel options can be adjusted to your specific needs. W-Series stations can have one pump or up to four pumps, depending on the tank chosen.
Simplex Stations
• HDPE or fi berglass (not shown) construction
• Station capacities of 100, 237 and 476 gallons available
• Various station heights available
Multiple-Pump Stations
• HDPE construction
• Station capacities of 476 and 486 gallons available
• 476-gallon tank allows for 1 or 2 pumps
• 486-gallon tank allows for 2, 3 or 4 pumps
• Various station heights available
The W-Series fi berglass tanks offer a multitude of station volumes and heights with diameters from 24 inches to 72 inches, and heights from 60 inches to 240 inches.
* Please visit www.eone.com for application and fl ow information
The E/One D-Series features a wetwell/
drywell design that provides a dry accessway
for ease of service. Plus a modular design
and one-piece core that permits simple
core replacement – should it ever become
necessary. Available in both simplex and
duplex grinder pump stations to fi t a wide
variety of applications, from single-family
homes to light commercial applications to
several homes in conjunction.
The tanks are made from tough, corrosion-
resistant HDPE for long life and zero upkeep.
Station capacities of 70 gallons to 500 gallons
are available.
THE W-SERIESEngineered for choice.
More builders and municipalities are opting for the ease and convenience of the E/One Indoor Unit, which offers easy access along with all the benefits of the D-Series. An attractive self-contained unit, the I-Series fits unobtrusively into a basement or garage with a clean, contemporary design that feels right at home with other major appliances.
It can be used as part of a new E/One sewer system or retrofit into an existing low pressure or gravity sewer system.
With its quiet, energy-efficient pump and sound insulating properties, the I-Series is easy to live with.
THE D-SERIESWetwell/Drywell for Superior
Serviceability
THE I-SERIES INDOOR UNITSelf-Contained for Indoor Installation
DESIGN
• Enhanced pump controls: expanded diagnostics, protection, and communications capabilities
• “Core” concept with integral level and motor controls
• Radial O-ring seals on all joints
• Thermally welded discharge assembly for high-pressure performance
• Differential pressure switch level control in separate, removable assembly
• Equalizer compensates for fl uctuations in atmospheric pressure while providing a sealed, water-tight level control system
• Integral check valve and anti-siphon valve assembly
• New, more resilient stator material enables higher pressure rating of 80 psi, using E/One proprietary stator chemistry
• All fasteners and hardware are 300 series stainless steel
RELIABILITY
• Huge double O-rings used for casting joint seals
• Casting joints designed for corrosive environment
• Indestructible level sensor housing
• Ultrasonically welded check valve assembly
• Superior corrosion protection – wet-applied coating on Class 30 cast iron vs. industry-standard powder coating
• Weld-free stainless steel stand
The Most Rugged, Longest-Lasting
Grinder Pump in the Industry
The progressing cavity pump itself is based on the Moineau principle. A rotor turns within a stator, creating a sequence of sealed chambers. The precision-cast and polished stainless steel rotor moves wastewater through these chambers at a nearly constant fl ow, over a wide range of conditions – from negative to abnormally high heads. Turning at just 1,725 rpm, the one-horsepower motor can pump fluid through more than two miles of small-diameter piping or elevation changes of over 185 feet.
PERFORMANCE
• Design pressures to 80 psi (185 feet total dynamic head)
• Progressing cavity pump provides predictable fl ow over varying system pressure
• 1 hp, 1725 rpm, air-cooled motor provides low speed, high torque operation, eliminating jams
• Field-proven, large-diameter grinding mechanism provides low inlet velocity, eliminating pump blinding or clogging
• Integral check valve protects against system back pressure; anti-siphon valve facilitates downhill pumping applications
SERVICEABILITY
• No preventive maintenance required
• Quick-release core latch on D-Series – no mounting bolts required
• Electrical quick disconnect (EQD) seals and connects without tools; uses single turn locking ring
• Detachable level sensor assem-bly; wireless design available using inductive coupling
• Discharge plumbing quickly disconnects from grade level
• Backward compatibility to earlier generations/designs
• Air-fi lled motor more effi cient than oil-fi lled motors and eliminates need to change and dispose of oil
• One pump for all series
• Backward-compatible EQD
237 gal
100 gal
476 gal
486 gal
99471_EOneSewerSystems.indd 299471_EOneSewerSystems.indd 2 9/22/16 9:50 AM9/22/16 9:50 AM
5-PP-20218/25/2021
PRESSURE SEWERSYSTEMS
Sewer Anywhere and SaveE/One Sewer Systems give engineers, builders, developers, municipal sanitarians and land planners unprecedented new freedom in land usage and sewer rehabilitation.
Easy to install. Easy to operate. And easy to maintain.
The sensible sewering solution that defies gravity and saves up to 50% – the E/One sewer system.
Environmentally sensitive. Economically sensible.™
E/One, Extreme, Engineered to do One Job Perfectly and Environmentally Sensitive Economically Sensible are trademarks for Environment One Corporation. Copyright 2016 Environment One Corporation. All rights reserved throughout the world.
NOBODY CAN TOUCH OUR CURVE.In a low pressure system, constant, predictable pump output is the foundation for proper hydraulic design. It enables the engineer to minimize retention time, pump wear, and keep scouring velocity at effective levels.
Environment One’s semi-positive displacement, progressing cavity pump has a nearly vertical H-Q curve. It is by far the most “forgiving” pump design – providing predictable flow over the full range of typical system pressures; strengths critical in a large-scale, low pressure sewer system.
E/One’s superior high head capability allows a system with few, if any, lift stations. And, it easily accommodates additional future connections without compromising system performance.
These E/One pump characteristics translate into:
• predictable hydraulic design
• lower collection system capital costs
• less maintenance
• lower operating costs
Environment One Corporation2773 Balltown RoadNiskayuna, NY USA 12309-1090Voice (01) 518.346.6161Fax 518.346.6188www.eone.com
A Precision Castparts CompanyLM000365 Rev D
High Heads/Negative Heads. Industry’s most reliable operation – rated for continuous duty of negative head to total dynamic head of 185 feet reduces the number of lift stations and pipe sizes. This cuts costs – both initially and in long-term operation and maintenance.
Constant Flow. The system pressures to be overcome by any given grinder pump in a low pressure system vary dramatically over the course of a day. E/One’s progressing cavity pump readily accommodates these pressure variations while maintaining a nearly constant flow without ever operating at “near shut off” – thus avoiding the wear and motor burn-out suffered by other pump types.
High Grinding Torque. Our unique pump system, driven by a one-horsepower motor turning at 1725 rpm, produces grinding torque greater than a larger horsepower pump turning at twice the speed.
Energy Efficient. The pump is activated automatically and runs for short periods.
Low Maintenance Submersible Motor.Low maintenance and long life are the hallmarks of our air-filled motor. Permanently lubricated ball bearings and Class F insulation eliminate the need for periodic oil changes and oil disposal costs required by oil-filled submersible motors.
Large-Diameter Grinder Assembly. Almost twice the diameter of most other types of grinder pumps, contributing to a dramatic reduction of inflow velocity for less wear and no blinding, clogging or jamming.
No Preventive Maintenance. Non-fouling static level sensors require no preventive maintenance. Because of our unique, near constant discharge rate, no main line flushing is required in a properly designed system.
Corrosion Resistance. Corrosion resistance is built into the E/One® design.
Serviceability. Our unique core design eliminates the need for in-field troubleshooting and pump servicing. This means lower maintenance costs and minimum homeowner inconvenience.
SOME KEY ADVANTAGES:
CONSULT FACTORYFOR INTERMITTENTUSE ABOVE 80 PSIOR 185 FEET TDH
LOW PRESSURE SYSTEM DESIGN PRESSURE
E/One Product Family
5-PP-20218/25/2021