Jacton Electromechanical Co.,Ltd | Tel: +86 (0)769 81585852 | Fax: +86 (0)769 81620195 Email: [email protected] | Web: www.screw-jack.com | Skype: jactonjack
Anti-Backlash Screw Jacks Screw jacks are used for positioning loads in numerous applications, however when the
load direction alternates between tension and compression within the operating cycle and
a high position accuracy must be maintained then a specific type of screw jack is
required. The Anti Backlash Machine Screw Jacks is recommended for such applications,
as it is able to reduce the axial backlash between the lead screw and the trapezoidal
screw thread in the gear to a practical minimum.
Axial backlash exists in standard screw jacks as the "gap" or "play" between the flanks of
the lead screw thread and the internal thread on the worm gear nut. This gap or play is
due not only to normal manufacturing tolerances, but to the fact that there must be some
clearances to prevent binding and galling when the screw jack is operating under load. In
most applications either the load direction is constant so axial backlash does not occur or
Jacton Electromechanical Co.,Ltd | Tel: +86 (0)769 81585852 | Fax: +86 (0)769 81620195 Email: [email protected] | Web: www.screw-jack.com | Skype: jactonjack
the position error caused by the axial backlash is considered negligible for the application.
However some applications require minimal or regulated axial backlash for accurate and
repeatable positioning. Such an application is for positioning the rollers in steel
straightening machines for tube, bar or sheet steel production.
Anti-backlash mechanism on screw jacks can be used to reduce axial-backlash to a
practical minimum or a regulated value. Reduction in axial backlash below this minimum is
not normally recommended as it can cause binding and excessive wear. As the screw jack
is operated over time the axial backlash will increase as the lead screw thread on the gear
wears due to normal operation. To compensate for this anti-backlash device can be
adjusted to re-set for the required amount of regulated backlash. To help with the
identification of wear machine screw jacks can also be fitted with a wear monitoring device
for visual use or with electronic sensing for integration into a motion control system.
Anti Backlash Screw Jacks Application Case 1
Above picture is special manufactured 450MM Stroke Inverted 2 Ton Anti Backlash Screw
Jack following customers requirements. The assemblies can be adjusted in the future, to
maintain the zero backlash, and precise location. Two flanges Anti Backlash Screw Jack,
big flange for IEC90 motor, another small flange for geared potentiometer. Special devices
like anti-backlash device, anti rotation keyed screw configurations, travel stroke controlled
limit switches, lengthening threads end, anti rust and anti dust protection tube etc.
Jacton Electromechanical Co.,Ltd | Tel: +86 (0)769 81585852 | Fax: +86 (0)769 81620195 Email: [email protected] | Web: www.screw-jack.com | Skype: jactonjack
Anti Backlash Screw Jacks Application Case 2
10" Stroke Inverted 2 Ton Anti-Backlash Gearing Screw Jack application in precision
Single-Point Adjustment (SPA) in roll forming tube and pipe, tube mill, pipe mills
industries. The assemblies can be adjusted in the future, to maintain the zero backlash,
and precise location. Non-Standard Lengthening Worm Shaft Anti-Backlash Gearing
Screw Jack, mechanical digital position indicator / counter is mounted on Non-Standard
Lengthening Worm Shaft. Manual operation two jacks system. Special devices like
anti-backlash device, lengthening worm shaft, anti rust and anti dust protection tube, cast
iron hand wheel etc.
Anti Backlash Screw Jacks FAQs
What are anti-backlash devices?
Anti-backlash devices are internal jack components used to minimize backlash (free
movement between the lifting screw and nut) in machine screw jacks.
Why are anti-backlash devices needed?
Anti-backlash devices are typically used in reversing load applications where the lifting
screw position is critical.
Where are anti-backlash devices used?
Anti-backlash devices are frequently used in steel mill applications where the screw jacks
are used to set and maintain the position of the movable upper roll of a rolling mill. In
operation, the initial weight of the roll pulls the lifting screw to one side of the nut. When
steel passes through the rolls, the load reverses on the lifting screw and movement in the
opposite direction is limited by the anti-backlash device. Other common applications
Jacton Electromechanical Co.,Ltd | Tel: +86 (0)769 81585852 | Fax: +86 (0)769 81620195 Email: [email protected] | Web: www.screw-jack.com | Skype: jactonjack
include screw jacks used to position communication antennas and solar panels. In these
applications, directional changes in the wind can buffet the panels thus affecting the
position of the lifting screw. During these high wind conditions, anti-backlash devices
minimize the lifting screw movement.
Will the anti-backlash device require adjustment?
When the internal nut threads begin to wear, lifting screw backlash increases. Subsequent
adjustment of the anti-backlash device compensates for the nut wear and allows the user
to limit the backlash to the recommended value. Adjustment frequency will vary depending
on load, duty cycle, and temperature. The anti-backlash device should be replaced when
no further adjustment is possible due to thread wear.
What effect do anti-backlash devices have on torque requirements?
Torque requirements for screw jack operation are affected by the clearance between the
lifting screw and nut thread. Adjusting anti-backlash devices (within recommended values
for each design) will not increase the torque to move a given load. If the backlash is set
below the recommended values, torque values will increase significantly and thread wear
will accelerate.
Can anti-backlash devices be used on ball screw jac ks and bevel ball actuators?
No. Rather, the use of oversized ball bearings in ball nut assemblies is recommended to
reduce endplay in ball screw jacks and bevel ball actuators.
“JACTON” Company Profiles
Precision worm gear screw jacks, lifting jacks, machine screw actuators, ball screw jacks,
trapezoidal screw jacks, bevel gear screw jacks, worm gear driven lift mechanism, spiral
bevel gears right angle gearbox, miter gears drives 90 degree gearbox, multiple units
screw jack lifting system arrangements manufacturers and suppliers in China – Jacton Electromechanical Co.,Ltd . Since 1997, only occupied 500 square meters for factory, up
to 2012, factory is occupied 5000 square meters with 55 employee staffs. With senior
engineers, experienced skilled workers and practiced sales teams, our company
consistently provides ideal mechanical power transmission solutions.
Application in roll forming line, theater stage lift table, solar tracking system, earth station
antennas, hydropower sluice gate, food processing line, coil sheet slitter line, tension
leveling line and straightening line, continuous galvanizing line, beverage production line,
railway maintenance lifting jack, angle tilt adjustments with double clevis, aircraft docking
system, printing press, plastic extruder, sewage auger, bonding equipment, metering
auger, sewage agitator, newspaper conveyor, bottling equipment, material handling, web
finishing, paper conveying, conveyor, cardboard box equipment, packaging, vertical pump
drive, sand spreader, residential mower, snow blower, mining equipment, crane,
agricultural, grain wagon, harvester, forage harvester, manure spreader, fertilizer spreader
and sewage conveyor etc.
Jacton Electromechanical Co.,Ltd | Tel: +86 (0)769 81585852 | Fax: +86 (0)769 81620195 Email: [email protected] | Web: www.screw-jack.com | Skype: jactonjack
Manufacturing Equipments include cnc lathes, gear cutting hobbing machines, radial
drilling machines, high speed thread whirling machines, worm shaft grinding machines,
vertical milling machines, high precision CNC machine tools, cnc precision automatic
lathes, lathes, punching machines, hydraulic straightening machines, polisher machines.
Testing equimments include noise meters, infrared thermometers, hardness testers, gear
meshing testing machines, micrometers, testing lifting screw moving smoothly adjustable
working table.
Customers are distributed throughout the world, such as USA, Canada, Mexico, Brazil,
Argentina, Chile, Australia, New Zealand, Japan, Korea, Thailand, India, Indonesia,
Malaysia, Philippines, Singapore, Vietnam, Sri Lanka, Pakistan, Iran, UAE, Saudi Arabia,
Turkey, South Africa, Egypt, Zambia, Germany, UK, Poland, Sweden, Slovak, Spain,
Greece, Italy, Russia, Netherland, Danmark, Belgium and Other Countries.