Cab
le t
ray
SyS
tem
S
1
IntroductionFactoriesLocations
General OverviewTypes OverviewMaterials & Finishes
Cable tray runsLight Duty Type (1.00 mm Thickness) LCT-25 , LCT-50
Medium Duty Type (1.20 mm Thickness) MCT-25 , MCT-50 ,MCT-75 ,MCT-100
Heavy Duty Type (1.50 mm Thickness)
HCT-25 , HCT-50 ,HCT-75 ,HCT-100
Very Heavy Duty Type (2.00 mm Thickness)
VCT-25 , VCT-50 ,VCT-75 ,VCT-100
Cable Tray FittingsBend 45°Bend 90°Tee BranchIntersectionVertical 90° Outside RiserVertical 90° Inside Riser Adjustable RiserReducerAdd-on Branch
Cable tray accessoriesConnectorBarrier Strip, Joint Plate, Crimping Type CopperEnd Plate, Drop Out PlateCable Tray CoverFraming System Accessories
Cable tray Support SystemsC - Channel SystemsCantilever Arm Support Accessories
Heavy Duty anchorsExpansion Steel Anchor - Stm
Drop in Anchor - SDa
Sleeve Anchor - SaS / Sab
Through Bolt (Wedge Anchor) - Stb
Shield Anchor - SSa
Ordering Cable TraySide Height Varieties AbbreviationsHow to OrderGeneral Information
Inde
x 246
89
11
1213
15
19
23
27282930313233343536
373839
4041
43444547
505152545658
6061
62
Cable maNaGemeNt SyStemSCable tray SyStemS
www.unimetal-ikk.com
Introduction-Factories-Locations
2
Cab
le t
ray
SyS
tem
S
3
Specialized Factory for Steel Products (Jeddah/KSa)Sigma Factoryِ for Steel Products (ajman & Umm al Quwain /Uae)Specialized Factory for Steel Products (6th of October/Egypt)Specialized Factory for Steel Products (amman/Jordan)
Uni-metal cable trays and accessories from SFSP are manufactured in compliance with :
- Nema Ve 1–2009 - Nema Ve 2–2006- IeC 61537 - bS eN 61537:2007 - bS 5750/bS eN 10130- bS eN 10131- bS eN 10051 - CeNeleC eN 50173-1- eIa/Ita 568 a- ISO/IeC 11801; 2002.
Cable trays are designed to meet most requirements of cable and electrical wire installations and comply to local and international standards of fabrication and finishing.
This catalogue is designed to be helpful to engineers and contractors in the application and selection of tray products for construction and maintenance.If a unique application requires a special product not included in this catalogue , SFSP engineering personnel are ready to furnish design consultation and realistic cost estimates. In addition, know-how are available for your convenience.
www.sfsp - ikk .com
ww
w.u
nim
etal
-ikk.
com
Cable maNaGemeNt SyStemSCable tray SyStemS
www.unimetal-ikk.com4
Factories
SAUDI ARABIA
SYRIA
NAMO
EGYPT
JORDAN
IRAQ IRAN
KUWAIT
UAE
QATAR
Bahrain
Jeddah
Cairo
Ajman
Umm Al Quwain
Amman
YEMENSUDAN
DJIBOUTI
LEBANON
SFSP - KSA/UAE/Egypt/Jordan
Locations
www.ikkgroup.com
Specialized / Sigma Factory for Steel Products
SFSPChart Lcations
for Building and Construction Materials
w w w . s f s p - i k k . c o m
O/SF/GLO
/LT/73
0/3
26-06-20
08
6th of October
www.sfsp-ikk.com
SFSP - Saudi arabiaSpecialized Factory for Steel ProductsJeddah - Saudi arabiaTel : +966 2 637 4482 Fax: +966 2 636 1963 [email protected]
SFSP - United arab emirates SIGma Factory for Steel Productsajman, United arab emiratesTel : +971 6 743 9907 Fax: +971 6 743 [email protected]
SIGma Factory for Steel ProductsUmm al Quwain, UaeTel : +971 6 767 0514Fax: +971 6 767 [email protected]
SFSP - eGyPtSpecialized Factory for Steel Products6th of October, Cairo - EgyptTel : +20 2 3831 2477 Fax: +20 2 3831 [email protected]
SFSP - JOrDaNSpecialized Factory for Steel Productsamman, JordanTel : +962 6 416 4216 Fax: +962 6 416 [email protected]
Cab
le t
ray
SyS
tem
S
5
SFSP is a leading manufacturer and fabricator of steel and aluminum products used for the support of equipment for industrial, commercial, utility and OEM installations. Our customers have access to the most complete support systems offered in the industry including metal framings, cable trays, pipe hangers, slotted angles, fasteners and others.(Our factory is equipped with an in-house hot dip galvanization facility) .
CNC machines
Hot-Dip Galvanization Process
Roll Forming Machine
ww
w.u
nim
etal
-ikk.
com
Cable maNaGemeNt SyStemSCable tray SyStemS
www.unimetal-ikk.com6
Uni-Metal trades in-house produced steel construction products, all designed and manufactured in SFSP plants located in KSA,UAE,Egypt and Jordan.
SaUDI arabIa
JeDDaHTel :+966 2 627 8222Fax: +966 2 627 [email protected]
JeDDaH/Ghurab ShowroomTel : +966 2 667 2000 Fax: +966 2 661 [email protected]
maK KaH / taIFTel : +966 2 558 1358Fax: +966 2 558 [email protected]
maD INaHTel : +966 4 864 9111Fax: +966 4 813 [email protected]
yaNbUTel : +966 4 390 1499Fax: +966 4 322 [email protected]
Kazakhstan
Russia
Spain
France
GermanyPoland
Greece
Albania
HungaryAustria
Slovakia
Czech RepUkraine
Maldova
Romania
Bulgaria
SerbiaCroatia
Italy
Turkey
Georgia
PortugalTurkmenistan
Afghanistan
Pakistan
India
Sri Lanka
TaiwanBangladesh
China
Myanmar
Thailand
Laos
Nepal
Uzbekistan
Tajikistan
Kyrgyzstan
IRAN
Tehran
Ashgabat
Kabol
EquatorialGuinea
Skakah
Gurayyat
Mak kahAl Taif
Beirut
SAUDI ARABIA
SYRIA
EGYPT
LEBANON
JORDAN
IRAQ
UAE
BAHRAIN
Najran
Khamis Mushayt
Riyadh
Hail Qassim
Yanbu
Jeddah
Dammam Manama
JubailHafr Al Batin
Gizan
Baha
Ma dinah
Hufuf
Cairo
YEMEN
SUDANChad
Niger
Aqaba
Al Kharj
Amman
Ajman
6th of October
Musa�ah
Jebel Ali
DohaQATAR
TabukLIBYAALGERIA
TUNISIA
Malta
MOROCCO
OMAN
KUWAIT
Tripoli Banghazi
AlgeriaOranTanger
Casablanka
Kuwait
Muscat
Sanaa’
Adan
Salalah
Irbil
Baku
DubaiSharjah
U A Q
Libreville
Nigeria
Cameroon
DR Congo
Zambia MalawiAngola
Botswana
SouthAfrica
Zimbabwe
Mozambique
Gabon Congo
Ethiopia
UgandaKenya
Eritrea
Somalia
Muqdisho
CentralAfrican
Republic
UnitedRepublic of
Tanzania
WindhoekNamibia
Bata
Mali
Burkina Faso
GhanaCote
d’lvoire
Guinea
Senegal
Mauritania
Benin
Abuja
StuttgartAstana
Yiwu
Luanda
Gaborone
Australia
New Zealand
Japan
Korea
Mongolia
Vietnam
Hatyai
Cambodia
Malaysia
Indonesia
New Guinea
Norway
UnitedKingdom
Ireland
Sweden
Denmark
Netherlands
Switzerland
Belgium
Philippines
Estonia
Latvia
Lithuania
AzerbaijanArmenia
Belarus
Istanbul
SydneyManaging Office
Main Branch
Branch
Factory
Design Office
Up-Coming Branch
Up-Coming Factory
Purchasing & Supply
2010
S a l e S
7
Kazakhstan
Russia
Spain
France
GermanyPoland
Greece
Albania
HungaryAustria
Slovakia
Czech RepUkraine
Maldova
Romania
Bulgaria
SerbiaCroatia
Italy
Turkey
Georgia
PortugalTurkmenistan
Afghanistan
Pakistan
India
Sri Lanka
TaiwanBangladesh
China
Myanmar
Thailand
Laos
Nepal
Uzbekistan
Tajikistan
Kyrgyzstan
IRAN
Tehran
Ashgabat
Kabol
EquatorialGuinea
Skakah
Gurayyat
Mak kahAl Taif
Beirut
SAUDI ARABIA
SYRIA
EGYPT
LEBANON
JORDAN
IRAQ
UAE
BAHRAIN
Najran
Khamis Mushayt
Riyadh
Hail Qassim
Yanbu
Jeddah
Dammam Manama
JubailHafr Al Batin
Gizan
Baha
Ma dinah
Hufuf
Cairo
YEMEN
SUDANChad
Niger
Aqaba
Al Kharj
Amman
Ajman
6th of October
Musa�ah
Jebel Ali
DohaQATAR
TabukLIBYAALGERIA
TUNISIA
Malta
MOROCCO
OMAN
KUWAIT
Tripoli Banghazi
AlgeriaOranTanger
Casablanka
Kuwait
Muscat
Sanaa’
Adan
Salalah
Irbil
Baku
DubaiSharjah
U A Q
Libreville
Nigeria
Cameroon
DR Congo
Zambia MalawiAngola
Botswana
SouthAfrica
Zimbabwe
Mozambique
Gabon Congo
Ethiopia
UgandaKenya
Eritrea
Somalia
Muqdisho
CentralAfrican
Republic
UnitedRepublic of
Tanzania
WindhoekNamibia
Bata
Mali
Burkina Faso
GhanaCote
d’lvoire
Guinea
Senegal
Mauritania
Benin
Abuja
StuttgartAstana
Yiwu
Luanda
Gaborone
Australia
New Zealand
Japan
Korea
Mongolia
Vietnam
Hatyai
Cambodia
Malaysia
Indonesia
New Guinea
Norway
UnitedKingdom
Ireland
Sweden
Denmark
Netherlands
Switzerland
Belgium
Philippines
Estonia
Latvia
Lithuania
AzerbaijanArmenia
Belarus
Istanbul
Sydney
baHaTel : +966 7 237 5929Fax: +966 7 237 [email protected]
al KHarJTel : +966 1 540 9982Fax: +966 1 540 [email protected]
HaFar al batINTel : +966 3 721 5915Fax: +966 3 721 [email protected]
NaJraNTel : +966 7 321 4038Fax: +966 7 321 [email protected]
QaSSImTel : +966 6 385 2186Fax: +966 6 382 [email protected]
DammamTel : +966 3 859 0097Fax: +966 3 857 [email protected]
KHamIS mUSHaytTel : +966 7 237 5929Fax: +966 7 237 8783 [email protected]
GIzaNTel : +966 7 321 6660Fax: +966 7 321 [email protected]
rIyaDHTel : +966 1 454 9282Fax: +966 1 456 [email protected]
tabUKTel : +966 4 422 6414Fax: +966 4 422 [email protected]
SKaKaH / QurayyatTel : +966 4 626 3904Fax: +966 4 626 [email protected]
HaIlTel : +966 6 543 3931Fax: +966 6 543 [email protected]
Dammam ShowroomTel : +966 3 834 9300Fax: +966 3 834 [email protected]
JUbaIlTel : +966 3 361 4390Fax: +966 3 361 [email protected]
HUFUFTel : +966 3 586 9732Fax: +966 3 584 [email protected]
Uae
DUbaI / al Quoz Tel : +971 4 347 8238Fax : +971 4 347 [email protected]
DUbaI / al rashidiyahTel : +971 4 285 6031Fax : +971 4 286 [email protected]
SHarJaHTel : +971 6 534 4092Fax: +971 6 534 [email protected]
abU DHabI / musaffahTel : +971 2 551 2334Fax: +971 2 551 [email protected]
ammaNTel : +962 6 556 3030Fax: +962 6 554 [email protected]
al SaleHIyaHTel : + 965 22 459 984Fax: + 965 22 459 [email protected]
DOHaTel : +974 451 3301/2/3Fax: +974 451 [email protected]
trIPOlITel : +218 21 719 9384 Fax: +218 21 717 [email protected]
lIbya
Qatar JOrDaN
KUWaIt
beIrUtTel : +961 1 858 277Fax: +961 1 858 [email protected]
lebaNON
maNamaTel : +973 175 64386 Fax: +973 175 [email protected]
mUSCatTel : + 968 24 59 1006fax : + 968 24 59 7006 [email protected]
OmaN
baHraIN
CaIrOTel:+20 2 346 8566 Fax:+20 2 346 [email protected]
GHOmHOUrIya StreetTel : +20 2 787 2152Fax: +20 2 593 [email protected]
eGyPt
CPU - KSA / JeDDaH Tel : +966 2 627 8275Fax: +966 2 627 [email protected]
TOSL - UAE / Jebel alITel : +971 4 886 0262Fax: +971 4 886 [email protected]
materIalS & PUrCHaSING
GermaNy StUttGartTel: +497 11 6868 7222 Fax: +497 11 6868 [email protected]
lebaNON beIrUt Tel : +961 1 841 155Fax : +961 1 841 [email protected]
DeSIGN OFFICe maNaGING OFFICe
CHINA - yIWUYiwu - Zhejiang ProvinceTel : +86 579 8545 3180Fax: +86 579 8542 [email protected]
ww
w.u
nim
etal
-ikk.
com
Cable maNaGemeNt SyStemSCable tray SyStemS
General Overview -types Overview-materials & Finishes-technical Data
8
Cab
le t
ray
SyS
tem
S
9
General Overview
types Overview and Components Uni-Metal cable trays and accessories from SFSP are manufactured in compliance with BS EN 61537, 2001/BS 5750/BS EN 10130/BS EN 10131/ BS EN 10051 and NEMA standards. And, as per cabling standards CENELEC EN 50173-1; EIA/ITA 568 A; ISO/IEC 11801; 2002.
We provide a wide range of products capable of providing the characteristics which respond to the proposed application, along with quality of assembly, speed of installation, and cost-saving cable trays.
All illustrations, drawings and descriptive material in this publication are of a generally informative nature only,and do not form a complete package of the specifications or description of the goods .Most of the dimensions shown are nominal .Uni-Metal can make modifications and design, materials or finishes as it deems necessary or desirable .
Light Duty - Cable Tray SystemLCT - 100
Thickness : 1.00 mm
Side Height : 25 and 50 mm
Length : 2440 mm / 3000 mm
Width : 50 - 1000 mm
Heavy Duty - Cable tray SystemHCT - 150
Thickness : 1.50 mm
Side Height : 25 ,50 ,75 and 100 mm
Length : 2440 mm / 3000 mm
Width : 50 - 1000 mm
medium Duty - Cable tray SystemMCT - 120
Thickness : 1.20 mm
Side Height : 25 ,50 ,75 and 100 mm
Length : 2440 mm / 3000 mm
Width : 50 - 1000 mm
Very Heavy Duty - Cable tray SystemVCT - 200
Thickness : 2.00 mm
Side Height : 25 ,50 ,75 and 100 mm
Length : 2440 mm / 3000 mm
Width : 50 - 1000 mm
- materIal tHICKNeSS
- materIalS
1.00 mm 1.20 mm 1.50 mm 2.00 mm
Pre-Galvanized, Hot-Dip Galvanized, Stainless Steel and Aluminium
ww
w.u
nim
etal
-ikk.
com
Cable maNaGemeNt SyStemSCable tray SyStemS
10
- SHaPeS OF aCCeSSOrIeS
.Cornered .Curved
.Serial
15
Oblong holes7 x 32
L
W
2525
25 25
327
H
- tyPeS OF PerFOratION
.Staggered
- DImeNSIONS
15
Oblong holes7 x 32
L
W
2525
25 25
327
- tyPeS OF SIDe HeIGHtS
.Straight
.Return Flange Inside
.Return Flange Outside
.C-Type Inside
.C-Type Outside
STR
RFI
RFO
CTI
CTO
Ge
ne
ra
l
Ov
er
vi
ew
.All dimensions are in mm
Cab
le t
ray
SyS
tem
S
11
mild Steel - Plaina. Hot rolled Steel Plates, Sheets and Coils S235 Jr, As per:EN 10025 -2 / DIN 17100 / BS 4360 / ASTM A 653M / ASTM A 1011/ ASTM A 1011-01a JIS 3101 / JIS 3106 / GB 700 / GB / T1591.ASTM A 907 / ASTM A 1018M.ASTM A 570M / ASTM A 572M.b. Cold rolled Steel DC 01,As per:EN 10130 / DIN 1623, Part 2 / BS 1449:1 / ASTM A366 / ASTM A 1008 / JIS G 3141 / GB 699.EN 10131 / ASTM A 568M
mild Steel - Galvanized C. Continuously Pre- Galvanized Hot–Dip Zinc Coated Steel DX 51D + z,As per: EN 10327 / DIN 17162 / BS 2989/ ASTM A 527M / ASTM A 653M / JIS G 3302.EN 10326/ EN 10142 / ASTM A 526, 527, 528/ ASTM A 146
D. Electro Galvanized Steel (Electrolytic Coating) DC01 + ze,As per: EN 10152 / DIN 17163 / ASTM A591 / JIS G 3313 / JIS G 3141/BS 1449:1EN 10131
Stainless SteelF.Austenitic Stainless Steels aISI 304 & 316, As per: ASTM A 240 /EN 10088-2/ DIN 17400 / BS 1449:2 / ASTM A480 / ASTM A666 / ISO 3506 / EN 10028-7 /JIS G 4304F.1 Stainless Steel Fasteners EN 3506F.2 Stainless Steel Wire BS 1554 ,ASTM A276
aluminiumG.aluminium 5052 & 6063
FINISHeS
1- Hot–DIP Galvanization After Fabrication As per:ASTM A 123 / ASTM A 153 / ISO 1461.BS 729 / DIN 50976
2- Zinc Electroplating After FabricationAs per:ASTM B633 / EN 12329 / ISO 4042/ BS 1706 / BS 3382 / DIN 50961
3- Powder CoatingEpoxy / Polyester / Epoxy & PolyesterBS 3900 / ISO 2409 / ISO 1519 / ISO 1520
materIalS
materials & Finishes
ww
w.u
nim
etal
-ikk.
com
Cable maNaGemeNt SyStemSCable tray SyStemS
www.unimetal-ikk.com
Cable tray runs-Light Duty Type lCt (1.00 mm thickness)
-medium Duty type mCt (1.20 mm thickness)
-Heavy Duty type HCt (1.50 mm thickness)
-Very Heavy Duty type VCt (2.00 mm thickness)
12
Cab
le t
ray
SyS
tem
S
13
lCt - 25(Side Height 25 mm)
Thickness : 1.00 mmSide Height : 25 mmLength : 2440 mm / 3000 mm Width : 50 - 300 mm
Cable tray Support distance (m) load kN/m
LCT 50 - 25 1.00 0.65
width (w) : 50 mm 1.20 0.37
1.50 0.18
2.00 0.07
LCT 100 -25 1.00 0.75
width (w) : 100 mm 1.20 0.46
1.50 0.23
2.00 0.09
LCT 150 -25 1.00 0.68
width (w) : 150 mm 1.20 0.51
1.50 0.25
2.00 0.09
LCT 200 -25 1.00 0.68
width (w) : 200 mm 1.20 0.47
1.50 0.26
2.00 0.10
LCT 225 -25 1.00 0.52
width (w) : 225 mm 1.20 0.36
1.50 0.22
2.00 0.10
LCT 300 -25 1.00 0.27
width (w) : 300 mm 1.20 0.18
1.50 0.10
2.00 0.04
32 7
25
L
W
50
32 7
25
L
W
50
Light Duty Cable Tray RunslCt - 1.00 mm thickness
Order Example: LCT25 - Side height (h) - Width(w) - Thickness - Side type for more ordering details, please check pages (61-62)
Width (mm)
Order example Item (h) (w) (t) type
50 lCt25 025 0050 1 rFI 100 lCt25 025 0100 1 rFI
ww
w.u
nim
etal
-ikk.
com
Light Duty -1.00 mm thickness
Cable maNaGemeNt SyStemSCable tray SyStemS
14
lCt - 50(Side Height 50 mm)
Thickness : 1.00 mmSide Height : 50 mmLength : 2440 mm / 3000 mm Width : 50 - 450 mm
Cable tray Support distance (m) load kN/m
LCT 50 -50 1.00 1.92
width (w) : 50 mm 1.20 1.33
1.50 0.84
2.00 0.40
LCT 100 -50 1.00 2.10
width (w) : 100 mm 1.20 1.45
1.50 0.92
2.00 0.50
LCT 150 -50 1.00 2.19
width (w) : 150 mm 1.20 1.50
1.50 0.96
2.00 0.53
LCT 200 -50 1.00 1.73
width (w) : 200 mm 1.20 1.48
1.50 0.94
2.00 0.52
LCT 225 -50 1.00 1.52
width (w) : 225 mm 1.20 1.13
1.50 0.72
2.00 0.39
LCT 300 -50 1.00 0.87
width (w) : 300 mm 1.20 0.59
1.50 0.37
2.00 0.19
LCT 400 -50 1.00 0.45
width (w) : 400 mm 1.20 0.30
1.50 0.18
2.00 0.08
LCT 450 -50 1.00 0.34
width (w) : 450 mm 1.20 0.22
1.50 0.13
2.00 0.05
32 7
25
25
W
50
L
25 25732
25
2525
Order Example: LCT50 - Side height (h) - Width(w) - Thickness - Side type for more ordering details, please check pages (61-62)
Width (mm)
Order example Item (h) (w) (t) type
50 lCt50 050 0050 1 rFI 100 lCt50 050 0100 1 rFI
www.unimetal-ikk.com
Light Duty - 1.00 mm thickness
Cab
le t
ray
SyS
tem
S
15
mCt - 25(Side Height 25 mm)
Thickness : 1.20 mmSide Height : 25 mmLength : 2440 mm / 3000 mm Width : 50 - 450 mm
Cable tray Support distance (m) load kN/m
MCT 50 - 25 1.00 0.77
width (w) : 50 mm 1.20 0.44
1.50 0.22
2.00 0.08
MCT 100 - 25 1.00 0.90
width (w) : 100 mm 1.20 0.55
1.50 0.27
2.00 0.10
MCT 150 - 25 1.00 0.92
Width (w) : 150 mm 1.20 0.61
1.50 0.30
2.00 0.11
MCT 200 - 25 1.00 0.93
width (w) : 200 1.20 0.64
1.50 0.32
2.00 0.12
CT 220 - 25 1.00 0.93
width (w) : 225 1.20 0.64
1.50 0.32
2.00 0.12
MCT 300 - 25 1.00 0.48
width (w) : 300 1.20 0.32
1.50 0.19
2.00 0.09
MCT 400 - 25 1.00 0.24
width (w) : 400 1.20 0.15
1.50 0.08
2.00 ….
MCT 450 - 25 1.00 0.17
width (w) : 450 1.20 0.11
1.50 ….
2.00 ….32 7
25
L
W
50
Order Example: MCT25 - Side height (h) - Width(w) - Thickness - Side type for more ordering details, please check pages (61-62)
Width (mm)
Order example Item (h) (w) (t) type
50 mCt25 025 0050 2 rFI 100 mCt25 025 0100 2 rFI
32 7
25
L
W
50
ww
w.u
nim
etal
-ikk.
com
medium Duty Cable tray runsmCt - 1.20 mm thickness
medium Duty - 1.20 mm thickness
Cable maNaGemeNt SyStemSCable tray SyStemS
16
mCt - 50(Side Height 50 mm)
Thickness : 1.20 mmSide Height : 50 mmLength : 2440 mm / 3000 mm Width : 50 - 450 mm
Cable tray Support distance (m) load kN/m
MCT 50 - 50 1.00 2.29
width (w) : 50 mm 1.20 1.59
1.50 1.01
2.00 0.48
MCT 100 - 50 1.00 2.51
width (w) : 100 mm 1.20 1.74
1.50 1.10
2.00 0.60
MCT 150 - 50 1.00 2.62
width (w) : 150 mm 1.20 1.80
1.50 1.15
2.00 0.63
MCT 200 - 50 1.00 2.48
width (w) : 200 1.20 1.85
1.50 1.17
2.00 0.65
MCT 225 - 50 1.00 2.20
width (w) : 225 1.20 1.85
1.50 1.18
2.00 0.65
MCT 300 - 50 1.00 1.52
width (w) : 300 1.20 1.04
1.50 0.65
2.00 0.35
MCT 400 - 50 1.00 0.80
width (w) : 400 1.20 0.54
1.50 0.33
2.00 0.16
MCT 450 - 50 1.00 0.61
width (w) : 450 1.20 0.41
1.50 0.24
2.00 0.11
Order Example: MCT50 - Side height (h) - Width(w) - Thickness - Side type for more ordering details, please check pages (61-62)
Width (mm)
Order example Item (h) (w) (t) type
50 mCt50 050 0050 2 rFI 100 mCt50 050 0100 2 rFI 32 7
25
25
W
50
L
25 25 732
25
2525
www.unimetal-ikk.com
medium Duty - 1.20 mm thickness
Cab
le t
ray
SyS
tem
S
17
Thickness : 1.20 mmSide Height : 75 mmLength : 2440 mm / 3000 mm Width : 100 - 450 mm
mCt - 75(Side Height 75 mm)
Cable tray Support distance (m) load kN/mMCT 100 - 75 1.00 4.45
width (w) : 100 mm 1.20 3.26
1.50 2.08
2.00 1.16
MCT 150 - 75 1.00 4.53
width (w) : 150 mm 1.20 3.32
1.50 2.19
2.00 1.22
MCT 200 - 75 1.00 2.48
width (w) : 200 1.20 2.48
1.50 2.26
2.00 1.25
MCT 225 - 75 1.00 2.20
width (w) : 225 1.20 2.20
1.50 2.20
2.00 1.27
MCT 300 - 75 1.00 1.63
width (w) : 300 1.20 1.63
1.50 1.37
2.00 0.75
MCT 400 - 75 1.00 1.21
width (w) : 400 1.20 1.14
1.50 0.71
2.00 0.38
MCT 450 - 75 1.00 1.06
width (w) : 450 1.20 0.87
1.50 0.54
2.00 0.28
32 7
25
25
W
75
L
25 25
medium Duty Cable tray runsmCt - 1.20 mm thickness
Order Example: MCT75 - Side height (h) - Width(w) - Thickness - Side type for more ordering details, please check pages (61-62)
Width (mm)
Order example Item (h) (w) (t) type
100 mCt75 075 0100 2 rFI 150 mCt75 075 0150 2 rFI
32 7
25
25
W
75
L
25 25
ww
w.u
nim
etal
-ikk.
com
medium Duty - 1.20 mm thickness
Cable maNaGemeNt SyStemSCable tray SyStemS
18
mCt - 100(Side Height 100 mm)
Cable tray Support distance (m) load kN/mMCT 100 - 100 1.00 5.00
width (w) : 100 mm 1.20 4.86
1.50 3.30
2.00 1.84
MCT 150 - 100 1.00 3.32
width (w) : 150 mm 1.20 3.32
1.50 3.03
2.00 1.95
MCT 200 - 100 1.00 2.47
width (w) : 200 mm 1.20 2.47
1.50 2.47
2.00 2.02
MCT 225 - 100 1.00 2.19
width (w) : 225 mm 1.20 2.19
1.50 2.19
2.00 2.05
MCT 300 - 100 1.00 1.63
width (w) : 300 mm 1.20 1.63
1.50 1.63
2.00 1.30
MCT 400 - 100 1.00 1.20
width (w) : 400 mm 1.20 1.20
1.50 1.20
2.00 0.67
MCT 450 - 100 1.00 1.06
width (w) : 450 mm 1.20 1.06
1.50 0.94
2.00 0.50
Thickness : 1.20 mmSide Height : 100 mmLength : 2440 mm / 3000 mm Width : 100 - 450 mm
Order Example: MCT100 - Side height (h) - Width(w) - Thickness - Side type for more ordering details, please check pages (61-62)
Width (mm)
Order example Item (h) (w) (t) type
100 mCt100 0100 0100 2 rFI 150 mCt100 0100 0150 2 rFI
732
25
25
25 25 732
L
100
W
25
25
25 25
www.unimetal-ikk.com
medium Duty - 1.20 mm thickness
Cab
le t
ray
SyS
tem
S
19
HCt - 25(Side Height 25 mm)
Cable tray Support distance (m) load kN/mHCT 50 - 25 1.00 0.95
width (w) : 50 mm 1.20 0.54
1.50 0.27
2.00 0.10
HCT 100 - 25 1.00 1.11
width (w) : 100 mm 1.20 0.68
1.50 0.34
2.00 0.13
HCT 150 - 25 1.00 1.13
width (w) : 150 mm 1.20 0.75
1.50 0.37
2.00 0.14
HCT 200 - 25 1.00 1.15
width (w) : 200 1.20 0.78
1.50 0.39
2.00 0.14
HCT 225 - 25 1.00 1.15
width (w) : 225 1.20 0.79
1.50 0.40
2.00 0.15
HCT 300 - 25 1.00 0.95
width (w) : 300 1.20 0.65
1.50 0.40
2.00 0.14
HCT 400 - 25 1.00 0.49
width (w) : 400 1.20 0.33
1.50 0.18
2.00 0.08
HCT 450 - 25 1.00 0.37
width (w) : 450 1.20 0.24
1.50 0.13
2.00 0.05
HCT 500 - 25 1.00 0.28
width (w) : 500 1.20 0.18
1.50 0.09
2.00 ….
HCT 600 - 25 1.00 0.16
width (w) : 600 1.20 0.09
1.50 ….
2.00 ….
Thickness : 1.50mmSide Height : 25 mmLength : 2440 mm / 3000 mm Width : 100 - 600 mm
32 7
25
L
W
50
Heavy Duty Cable tray runsHCt - 1.50 mm thickness
Order Example: HCT25 - Side height (h) - Width(w) - Thickness - Side type for more ordering details, please check pages (61-62)
Width (mm)
Order example Item (h) (w) (t) type
100 HCt25 0025 0100 3 rFI 150 HCt25 0025 0150 3 rFI
32 7
25
L
W
50w
ww
.uni
met
al-ik
k.co
m
Heavy Duty - 1.50 mm thickness
Cable maNaGemeNt SyStemSCable tray SyStemS
20
HCt - 50(Side Height 50 mm)
Cable tray Support distance (m) load kN/mHCT 50 - 50 1.00 2.85
width (w) : 50 mm 1.20 1.97
1.50 1.25
2.00 0.60
HCT 100 - 50 1.00 3.12
width (w) : 100 mm 1.20 2.16
1.50 1.37
2.00 0.76
HCT 150 - 50 1.00 3.25
width (w) : 150 mm 1.20 2.25
1.50 1.43
2.00 0.78
HCT 200 - 50 1.00 3.30
width (w) : 200 1.20 2.30
1.50 1.45
2.00 0.80
HCT 225 - 50 1.00 3.33
width (w) : 225 1.20 2.32
1.50 1.47
2.00 0.80
HCT 300 - 50 1.00 2.57
width (w) : 300 1.20 2.06
1.50 1.30
2.00 0.70
HCT 400 - 50 1.00 1.60
width (w) : 400 1.20 1.05
1.50 0.65
2.00 0.35
HCT 450 - 50 1.00 1.23
width (w) : 450 1.20 0.83
1.50 0.50
2.00 0.25
HCT 500 - 50 1.00 0.95
width (w) : 500 1.20 0.65
1.50 0.35
2.00 0.19
HCT 600 - 50 1.00 0.63
width (w) : 600 1.20 0.41
1.50 0.24
2.00 0.10
HCT 700 - 50 1.00 0.43
width (w) : 700 1.20 0.27
1.50 0.14
2.00 x
Thickness : 1.50mmSide Height : 50 mmLength : 2440 mm / 3000 mm Width : 50 - 900 mm
Order Example: HCT50 - Side height (h) - Width(w) - Thickness - Side type for more ordering details, please check pages (61-62)
Width (mm)
Order example Item (h) (w) (t) type
50 HCt50 0050 0050 3 rFI 100 HCt50 0050 0100 3 rFI
32 7
25
25
W
50
L
25 25
www.unimetal-ikk.com
Heavy Duty - 1.50 mm thickness
Cable tray Support distance (m) load kN/m
HCT 750 - 50 1.00 0.35
width (w) : 750 1.20 0.22
1.50 0.10
2.00 x
HCT 900 - 50 1.00 0.20
width (w) : 900 1.20 0.10
1.50 0.03
2.00 x
Cab
le t
ray
SyS
tem
S
21
HCt - 75(Side Height 75 mm)
Cable tray Support distance (m) load kN/mHCT 100 -75 1.00 5.50
width (w) : 100 mm 1.20 4.05
1.50 2.55
2.00 1.42
HCT 150 -75 1.00 5.20
width (w) : 150 mm 1.20 4.20
1.50 2.70
2.00 1.50
HCT 200 -75 1.00 3.89
width (w) : 200 mm 1.20 3.89
1.50 2.80
2.00 1.56
HCT 225 -75 1.00 3.45
width (w) : 225 mm 1.20 3.45
1.50 2.85
2.00 1.58
HCT 300 -75 1.00 2.57
width (w) : 300 mm 1.20 2.57
1.50 2.57
2.00 1.49
HCT 400 -75 1.00 1.90
width (w) : 400 mm 1.20 1.90
1.50 1.43
2.00 0.77
HCT 450 -75 1.00 1.68
width (w) : 450 mm 1.20 1.68
1.50 1.08
2.00 0.58
HCT 500 -75 1.00 1.50
width (w) : 500 mm 1.20 1.38
1.50 0.86
2.00 0.45
HCT 600 -75 1.00 1.22
width 600 mm 1.20 0.90
1.50 0.55
2.00 0.27
HCT 700 -75 1.00 0.94
width 700 mm 1.20 0.63
1.50 0.37
2.00 0.16
Thickness : 1.50 mmSide Height : 75 mmLength : 2440 mm / 3000 mm Width : 100 - 700 mm
Heavy Duty Cable tray runsHCt - 1.50 mm thickness
Order Example: HCT75 - Side height (h) - Width(w) - Thickness - Side type for more ordering details, please check pages (61-62)
Width (mm)
Order example Item (h) (w) (t) type
100 HCt75 0075 0100 3 rFI 150 HCt75 0075 0150 3 rFI
32 7
25
25
W
75
L
25 25
ww
w.u
nim
etal
-ikk.
com
Heavy Duty - 1.50 mm thickness
Cable maNaGemeNt SyStemSCable tray SyStemS
22
HCt - 100(Side Height 100 mm)
Cable tray Support distance (m) load kN/mHCT 100 - 100 1.00 7.82
width (w) : 100 mm 1.20 6.07
1.50 4.10
2.00 2.30
HCT 150 - 100 1.00 5.19
width (w) : 150 mm 1.20 5.19
1.50 4.35
2.00 2.42
HCT 200 - 100 1.00 3.88
width (w) : 200 mm 1.20 3.88
1.50 3.88
2.00 2.52
HCT 225 - 100 1.00 3.44
width (w) : 225 mm 1.20 3.44
1.50 3.44
2.00 2.56
HCT 300 - 100 1.00 2.56
width (w) : 300 mm 1.20 2.56
1.50 2.56
2.00 2.56
HCT 400 - 100 1.00 1.89
width (w) : 400 mm 1.20 1.89
1.50 1.89
2.00 1.35
HCT 450 - 100 1.00 1.67
width (w) : 450 mm 1.20 1.67
1.50 1.67
2.00 1.00
2.50 0.63
HCT 500 - 100 1.00 1.49
width (w) : 500 mm 1.20 1.49
1.50 1.49
2.00 0.80
HCT 600 - 100 1.00 1.22
width 600 mm 1.20 1.22
1.50 0.98
2.00 0.50
HCT 700 - 100 1.00 1.02
width 700 mm 1.20 1.02
1.50 0.67
2.00 0.33
Thickness : 1.50 mmSide Height : 100 mmLength : 2440 mm / 3000 mm Width : 100 - 700 mm
Order Example: HCT100 - Side height (h) - Width(w) - Thickness - Side type for more ordering details, please check pages (61-62)
Width (mm)
Order example Item (h) (w) (t) type
100 HCt100 0100 0100 3 rFI 150 HCt100 0100 0150 3 rFI
732
L
100
W
25
25
25 25
www.unimetal-ikk.com
Heavy Duty - 1.50 mm thickness
Cab
le t
ray
SyS
tem
S
23
VCt - 25(Side Height 25 mm)
Cable tray Support distance (m) load kN/m
VCT 50 - 25 1.00 1.23
width (w) : 50 mm 1.20 0.70
1.50 0.35
2.00 0.14
VCT 100 - 25 1.00 1.45
width (w) : 100 mm 1.20 0.88
1.50 0.42
2.00 0.17
VCT 150 - 25 1.00 1.48
width (w) : 150 mm 1.20 0.98
1.50 0.48
2.00 0.18
VCT 200 - 25 1.00 1.50
width (w) : 200 1.20 1.03
1.50 0.50
2.00 0.18
VCT 225 - 25 1.00 1.50
width (w) : 225 1.20 1.03
1.50 0.52
2.00 0.18
VCT 300 - 25 1.00 1.52
width (w) : 300 1.20 1.04
1.50 0.53
2.00 0.18
VCT 400 - 25 1.00 1.20
width (w) : 400 1.20 0.82
1.50 0.50
2.00 0.18
VCT 450 - 25 1.00 0.92
width (w) : 450 1.20 0.62
1.50 0.37
2.00 0.18 32 7
25
L
W
50
Thickness : 2.0 mmSide Height : 25 mmLength : 2440 mm / 3000 mm Width : 50 - 450 mm
Very Heavy Duty Cable tray runsVCt - 2.00 mm thickness
Order Example: VCT25 - Side height (h) - Width(w) - Thickness - Side type for more ordering details, please check pages (61-62)
Width (mm)
Order example Item (h) (w) (t) type
50 VCt25 0025 0050 4 rFI 100 VCt25 0025 0100 4 rFI
32 7
25
L
W
50w
ww
.uni
met
al-ik
k.co
m
Very Heavy Duty -2.00 mm thickness
Cable maNaGemeNt SyStemSCable tray SyStemS
24
VCt - 50(Side Height 50 mm)
Cable tray Support distance (m) load kN/m
VCT 50 - 50 1.00 3.77
width (w) : 50 mm 1.20 2.60
1.50 1.65
2.00 0.78
VCT 100 - 50 1.00 4.13
width (w) : 100 mm 1.20 2.86
1.50 1.83
2.00 1.00
VCT 150 - 50 1.00 4.30
width (w) : 150 mm 1.20 2.98
1.50 1.88
2.00 1.05
VCT 200 - 50 1.00 4.40
width (w) : 200 1.20 3.05
1.50 1.92
2.00 1.07
VCT 225 - 50 1.00 4.43
width (w) : 225 1.20 3.06
1.50 1.95
2.00 1.07
VCT 300 - 50 1.00 4.47
width (w) : 300 1.20 3.12
1.50 1.97
2.00 1.08
VCT 400 - 50 1.00 3.42
width (w) : 400 1.20 2.64
1.50 1.66
2.00 0.90
VCT 450 - 50 1.00 2.97
width (w) : 450 1.20 2.04
1.50 1.27
2.00 0.68
VCT 500 - 50 1.00 2.36
width (w) : 500 1.20 1.60
1.50 1.00
2.00 0.50
VCT 600 - 50 1.00 1.57
width (w) : 600 1.20 1.06
1.50 0.64
2.00 0.32
VCT 700 - 50 1.00 1.10
width (w) : 700 1.20 0.72
1.50 0.42
2.00 0.19
Cable tray Support distance (m) load kN/m
VCT 800 - 50 1.00 0.80
width (w) : 800 1.20 0.50
1.50 0.28
2.00 0.10
VCT 900 - 50 1.00 0.58
width (w) : 900 1.20 0.36
1.50 0.18
2.00 X
VCT 1000 - 50 1.00 0.43
width (w) : 1000 1.20 0.25
1.50 0.10
2.00 X
Thickness : 2.0 mmSide Height : 50 mmLength : 2440 mm / 3000 mm Width : 50 - 1000 mm
Order Example: VCT50 - Side height (h) - Width(w) - Thickness - Side type for more ordering details, please check pages (61-62)
Width (mm)
Order example Item (h) (w) (t) type
50 VCt50 0050 0050 4 rFI 100 VCt50 0050 0100 4 rFI
32 7
25
25
W
50
L
25 25
www.unimetal-ikk.com
Very Heavy Duty -2.00 mm thickness
Cab
le t
ray
SyS
tem
S
25
VCt - 75(Side Height 75 mm)
Cable tray Support distance (m) load kN/m
VCT 100 - 75 1.00 7.31
width (w) : 100 mm 1.20 5.39
1.50 3.44
2.00 1.92
VCT 150 - 75 1.00 7.52
width (w) : 150 mm 1.20 5.62
1.50 3.62
2.00 2.02
VCT 200 - 75 1.00 6.92
width (w) : 200 1.20 5.72
1.50 3.73
2.00 2.07
VCT 300 - 75 1.00 4.58
width (w) : 300 1.20 4.58
1.50 3.86
2.00 2.13
VCT 400 - 75 1.00 3.40
width (w) : 400 1.20 3.40
1.50 3.40
2.00 1.90
VCT 450 - 75 1.00 3.00
width (w) : 450 1.20 3.00
1.50 2.65
2.00 1.45
VCT 500 - 75 1.00 2.70
width (w) : 500 1.20 2.70
1.50 2.10
2.00 1.13
VCT 600 - 75 1.00 2.22
width (w) : 600 1.20 2.22
1.50 1.38
2.00 0.73
VCT 700 - 75 1.00 1.87
width (w) : 700 1.20 1.58
1.50 0.95
2.00 0.49
VCT 800 - 75 1.00 1.60
width (w) : 800 1.20 1.15
1.50 0.68
2.00 0.33
Cable tray Support distance (m) load kN/m
VCT 900 - 75 1.00 1.30
width (w) : 900 1.20 0.86
1.50 0.50
2.00 0.21
VCT 1000 - 75 1.00 1.01
width (w) : 1000 1.20 0.65
1.50 0.36
2.00 0.13
Thickness : 2.0 mmSide Height : 75 mmLength : 2440 mm / 3000 mm Width : 100 - 1000 mm
Very Heavy Duty Cable tray runsVCt - 2.00 mm thickness
Order Example: VCT75 - Side height (h) - Width(w) - Thickness - Side type for more ordering details, please check pages (61-62)
Width (mm)
Order example Item (h) (w) (t) type
50 VCt75 0075 0050 4 rFI 100 VCt75 0075 0100 4 rFI
32 7
25
25
W
75
L
25 25
ww
w.u
nim
etal
-ikk.
com
Very Heavy Duty -2.00 mm thickness
Cable maNaGemeNt SyStemSCable tray SyStemS
26
VCt - 100(Side Height 100 mm)
Cable tray Support distance (m) load kN/m
VCT 100 - 100 1.00 10.65
width (w) : 100 mm 1.20 8.07
1.50 5.46
2.00 3.05
VCT 150 - 100 1.00 9.25
width (w) : 150 mm 1.20 8.34
1.50 5.78
2.00 3.23
VCT 200 - 100 1.00 6.92
width (w) : 200 1.20 6.92
1.50 5.95
2.00 3.35
VCT 300 - 100 1.00 4.58
width (w) : 300 1.20 4.58
1.50 4.58
2.00 3.48
VCT 400 - 100 1.00 3.40
width (w) : 400 1.20 3.40
1.50 3.40
2.00 3.25
VCT 500 - 100 1.00 2.69
width (w) : 500 1.20 2.69
1.50 2.69
2.00 1.98
VCT 600 - 100 1.00 2.20
width (w) : 600 1.20 2.20
1.50 2.20
2.00 1.30
VCT 700 - 100 1.00 1.86
width (w) : 700 1.20 1.86
1.50 1.70
2.00 0.90
VCT 800 - 100 1.00 1.60
width (w) : 800 1.20 1.60
1.50 1.23
2.00 0.63
VCT 900 - 100 1.00 1.39
width (w) : 900 1.20 1.39
1.50 0.92
2.00 0.45
VCT 1000 - 100 1.00 1.79
width (w) : 1000 1.20 1.18
1.50 0.70
2.00 0.32
Thickness : 2.00 mmSide Height : 100 mmLength : 2440 mm / 3000 mm Width : 100 - 1000 mm
Order Example: VCT100 - Side height (h) - Width(w) - Thickness - Side type for more ordering details, please check pages (61-62)
Width (mm)
Order example Item (h) (w) (t) type
100 VCt100 0100 0050 4 rFI 150 VCt100 0100 0100 4 rFI
732
L
100
W
25
25
25 25
732
25
25
25 25
www.unimetal-ikk.com
Very Heavy Duty -2.00 mm thickness
Cab
le t
ray
SyS
tem
S
Cable Tray Fittings- bend 45°- bend 90°- Intersection- tee branch
- Vertical 90° Outside Riser- Vertical 90° Inside Riser - adjustable riser- reducer- add-on branch
27
Cable maNaGemeNt SyStemSCable tray SyStemS
28
Order Example: 160 - Side height (h) - Width(w) - Thickness - Side type for more ordering details, please check pages (61-62)
Order Example: 170 - Side height (h) - Width(w) - Thickness - Side type for more ordering details, please check pages (61-62)
- bend 45°- cornered 160 - 161
160
170
- bend 45°- curved 170 - 171
Width (mm)
Order example Item (h) (w) (t) type
50 170 050 0050 2 rFI 100 170 050 0100 2 rFI
Width (mm)
Order example Item (h) (w) (t) type
50 160 050 0050 2 rFI 100 161 050 0100 2 rFI
161
radius r = 200 mm
171
Cab
le t
ray
SyS
tem
S
29
251
251t250t
250
Order Example:240 - Side height (h) - Width(w) - Thickness - Side type for more ordering details, please check pages (61-62)
For this type, all specifications are the same as other bend 90o types.Order No. shall be the same as curved type,but add the letter T .ex: 250 050 0050 2 ; Curved type 250t 050 0050 2 ; Cornered/Short type
Order Example: 250 - Side height (h) - Width(w) - Thickness - Side type for more ordering details, please check pages (61-62)
- bend 90°- cornered 240 - 241 - 242
- bend 90°- curved 250 - 251
Width (mm)
Order example Item (h) (w) (t) type
50 240 050 0050 2 rFI 100 241 050 0100 2 rFI
Width (mm)
Order example Item (h) (w) (t) type
50 250 050 0050 2 rFI 100 250 050 0100 2 rFI
radius r = 200 mm
Cornered/Short
Cable Tray Fittingsbend 90° (cornered / curved)
240 241
242
ww
w.u
nim
etal
-ikk.
com
Cable maNaGemeNt SyStemSCable tray SyStemS
www.unimetal-ikk.com30
Order Example: 320 - Side height (h) - Width (w) - Thickness (t) - Side type for more ordering details, please check pages (61-62)
Order Example: 330 - Side height (h) - Width(w) - Thickness - Side type for more ordering details, please check pages (61-62)
- tee branch - cornered 320 - 321 - 322
- tee branch - curved 330 - 331
Width (mm)
Order example Item (h) (w) (t) type
50 320 050 0050 2 rFI 100 321 050 0100 2 rFI
Width (mm)
Order example Item (h) (w) (t) type
50 330 050 0050 2 rFI 100 330 050 0100 2 rFI
radius r = 200 mm
320
322
330 331
321
Cab
le t
ray
SyS
tem
S
31
Order Example: 400 - Side height (h) - Width(w) - Thickness - Side type for more ordering details, please check pages (61-62)
- Intersection - cornered 400 - 401
- Intersection - curved 410 - 411
radius r = 200 mm
Order Example: 410 - Side height (h) - Width (w) - Thickness (t) - Side type for more ordering details, please check pages (61-62)
Width (mm)
Order example Item (h) (w) (t) type
50 400 050 0050 2 rFI 100 401 050 0100 2 rFI
Width (mm)
Order example Item (h) (w) (t) type
50 410 050 0050 2 rFI 100 410 050 0100 2 rFI
Cable Tray FittingsIntersection (cornered / curved)
400
410 411
401
ww
w.u
nim
etal
-ikk.
com
Cable maNaGemeNt SyStemSCable tray SyStemS
www.unimetal-ikk.com32
- Vertical 90o (outside riser) - cornered 480 - 481 - 482
- Vertical 90o (inside riser) - curved 490
radius r = 200 mm
Order Example: 480 - Side height (h) - Width (w) - Thickness (t) - Side type for more ordering details, please check pages (61-62)
Order Example: 490 - Side height (h) - Width (w) - Thickness (t) - Side type for more ordering details, please check pages (61-62)
Width (mm)
Order example Item (h) (w) (t) type
50 480 050 0050 2 rFI 100 481 050 0100 2 rFI
Width (mm)
Order example Item (h) (w) (t) type
50 490 050 0050 2 rFI 100 490 050 0100 2 rFI
480 482
481
Cab
le t
ray
SyS
tem
S
33
- Vertical 90o (inside riser) - cornered 560 - 561 - 562
- Vertical 90o (outside riser) - curved 570
radius r = 200 mm
Order Example: 560 - Side height (h) - Width (w) - Thickness (t) - Side type for more ordering details, please check pages (61-62)
Order Example: 570 - Side height (h) - Width (w) - Thickness (t) - Side type for more ordering details, please check pages (61-62)
Width (mm)
Order example Item (h) (w) (t) type
50 560 050 0050 2 rFI 100 561 050 0100 2 rFI
Width (mm)
Order example Item (h) (w) (t) type
50 570 050 0050 2 rFI 100 570 050 0100 2 rFI
Cable Tray FittingsVertical 90o inside riser (cornered / curved)
560 562
561
ww
w.u
nim
etal
-ikk.
com
Cable maNaGemeNt SyStemSCable tray SyStemS
34
- adjustable riser 640
- Custom risers
Order Example: 640 - Side height (h) - Width (w) - Thickness (t) - Side type - Length (L) - Angle (r) for more ordering details, please check pages (61-62)
Custom risers are suitable for 45° and 60° angles
45°60°
For inquiries, use same code as adjustable risers and add the angle desired at the end, ex:
for custom riser 45° angle• 640 050 0300 4 STR 3000/45 for custom riser 60° angle• 660 050 0300 4 STR 3000/60
Width (mm)
Order example Item (h) (w) (t) type (L) (r)
50 640 050 0050 2 Str 3000 /45100 640 050 0100 2 Str 3000 /45
Angle: 45° Angle: 60°
- reducer - central 680-681
W1
W2
hOrder Example: 680 - Side height (h) - Width (w1) - Width (w2)- Thickness (t) - Side type for more ordering details, please check pages (61-62)
Width (mm)
Order example Item (h) (w1) (w2) (t) type
50 680 050 0300 050 2 rFI 100 681 050 0400 050 2 rFI
681
680
Cab
le t
ray
SyS
tem
S
35
- Right side 690 - 691
- Left side 700 - 701
Order Example: 690 - Side height (h) - Width (w1) - Width (w2)- Thickness (t) - Side type for more ordering details, please check pages (61-62)
Order Example: 700 - Side height (h) - Width (w1) - Width (w2)- Thickness (t) - Side type for more ordering details, please check pages (61-62)
Width (mm)
Order example Item (h) (w1) (w2) (t) type
50 690 050 0300 050 2 rFI 100 691 050 0400 050 2 rFI
Width (mm)
Order example Item (h) (w1) (w2) (t) type
50 700 050 0300 050 2 rFI 100 701 050 0400 050 2 rFI
Cable Tray FittingsReducer (central / right / left)
690
700
691
701
ww
w.u
nim
etal
-ikk.
com
Cable maNaGemeNt SyStemSCable tray SyStemS
www.unimetal-ikk.com36
- add - on branch / cornered 800
- add - on branch / curved 810
radius r = 200 mm
Order Example: 800 - Side height (h) - Width (w) - Thickness (t) - Side type for more ordering details, please check pages (61-62)
Order Example: 810 - Side height (h) - Width (w) - Thickness (t) - Side type for more ordering details, please check pages (61-62)
Width (mm)
Order example Item (h) (w) (t) type
50 800 050 0050 2 rFI 100 800 050 0100 2 rFI
Width (mm)
Order example Item (h) (w) (t) type
50 810 050 0050 2 rFI 100 810 050 0100 2 rFI
Cab
le t
ray
SyS
tem
S
Cable tray accessories- Connector- barrier Strip- Joint Plate- Reducing Angle
- end Plate- Drop-out Plate- Cable tray Cover- Framing System Acc.
37
Cable maNaGemeNt SyStemSCable tray SyStemS
www.unimetal-ikk.com38
- Straight connector 1000
- Angle connector 1010/1020
240
h
h
150
240
w
h
240
50
h
240
h
20
240
h
150
240
w
h
240
50
h
240
h
20
240
h
150
240
w
h
240
50
h
240
h
20
240
Order Example: 1000 - Side height (h) - Thickness (t) for more ordering details, please check pages (61-62)
1010
1000
1020
Order Example: 1010 - Side height (h) - Width (w) - Thickness (t) for more ordering details, please check pages (61-62) Order Example:
1020 - Side height (h) - Width (w) - Thickness (t) for more ordering details, please check pages (61-62)
Order example Item (h) (t)
1000 050 2 1000 100 2
Width (mm)
Order example Item (h) (w) (t)
20 1010 050 0020 2 Width (mm)
Order example Item (h) (w) (t)
50 1020 050 0050 2
- adjustable connector 1030/1040
120
120
For M6 Bolt
h
h
h
w
h
50
240
1030
1040 Order Example: 1030 - Side height (h) - Thickness (t) for more ordering details, please check pages (61-62)
Order Example: 1040 - Side height (h) - Thickness (t) for more ordering details, please check pages (61-62)
7 x 38 for M6 Bolt
Order example Item (h) (t)
1030 050 2 Order example Item (h) (t)
1040 050 2
Cab
le t
ray
SyS
tem
S
39
h
25
for more ordering details, please check pages (61-62)
- Wrap-over connector 1050
- Corner connector 1060
h
h
w
h
50
240
240
150
1050 1060
1070
-Available with differnt side height types.
Framing System Accessories
- barrier strip 1070
- Joint plate / Fish plate 1080
- end plate 1100
- Drop-out plate 1110
- Crimping Type Copper tubular Cable terminal ends - 1200
- tinned Copper Flexible braids Crimped with Connectors/ terminals - 1300
W
h
W= w minus 7 mm
150W
1100 1110 1080
Available Lengths: 2440 / 3000 mm
Width = width of tray minus 7 mm
G
ED C
H B
ww
w.u
nim
etal
-ikk.
com
Size mm
2
Dimensions (mm) Current rating AMPJ E1 E2
4
50100150200
6666
6666
50505050
10
50100150200
6666
6666
90909090
16
100150200250300
8.58.58.58.58.5
8.58.58.58.58.5
125125125125125
25
100150200250300
1010101010
1010101010
160160160160160
Cable mm
2Stud Hole
Dimensions (mm)
A C D G H B J
1.5 6.5 1.8 3.7 10 4 6 6 18
2.5 6.58.4
2.42.4
44.2
1012
56
69
88
2126
4 6.58.4
3.13.1
4.85.0
1012
56
69
88
2126
6 6.58.4
3.83.8
5.55.5
1012
56
69
1010
2428
10 6.58.4
4.54.5
6.26.2
1112
66
79
1010
2628
16 6.58.4
5.45.4
7.17.1
1212
77
77
1212
3030
20 8.4 6 7.7 12 7 7 12 32
25 6.58.4
6.86.8
8.88.8
1313
77
77
1212
3030
Cable maNaGemeNt SyStemSCable tray SyStemS
www.unimetal-ikk.com40
- Cable tray cover
- Cable tray cover with locking clamp 2100
2000
2010
2100
Order Example: 2000 - Type - Width (w) - Thickness (t) for more ordering details, please check pages (61-62)
Order Example: 2100 - Width (w) - Thickness (t) for more ordering details, please check pages (61-62)
Functions Cable tray covers shall be considered for any of the following purposes:• Protection from falling objects or debris, as may occur beneath personnel walkways.• Shielding from ultra-violet rays of the sun and guarding against other weathering elements.• Minimizing accumulation of foreign contaminants such as ash or other industrial deposits.• Protection of cables and personnel where a riser tray penetrates a floor or grating.
Covers Side Height Types :• Solid without flange• Solid with flange• Ventilated without flange• Ventilated with flange
- (SOF)
- (SWF)
- (VOF)
- (VWF)
- Cable Ladder covers are supplied with or without a 15 mm downturned flange.- Straight section covers are furnished 3000 mm long. All fitting covers are furnished in solid design only.
Covers Side Height Types :• Solid without flange - (VOF)
• Solid with flange - (VWF)
Locking clampThickness: 2mm
- Ventilated cover- Solid cover
Width (mm)
Order example Item Type (w) (t)
50 2000 SWF 050 2
Width (mm)
Order example Item (w) (t)
50 2100 050 2
LockCover
Tray
Cab
le t
ray
SyS
tem
S
41
- Materials : low carbon steel , carbon steel - Steel S235 , grade 4.6 , 4.8 and 8.8- Surface : plain , black , zinc plated - Length = X (mm) – Y (mm)
Fully threaded rods Grade 4.6 DIN 975
Carriage Bolts with Nut Below Head DIN 603
Roofing Bolts
S
m
S
d
D
S
d
D
Zinc PlatedThread - ZP
Zinc Platedfor bolt - ZP
Zinc PlatedDimension- ZP
D
[mm]
D
[mm]
S/mDIN
[mm]
SDIN
[mm]
S/mISO
[mm]
SEN
[mm]
e
[mm]
d
[mm]
d
[mm]
s
[mm]
s
[mm]
Length
[mm]
Load
cap.
[kN]
Threaded Rods, Hexagon Head Bol ts, Nuts, Washers
FR AMI NG SY STEM S ACC ESSORI ES
Order Example : TR - ZP - M 12 × 1000
Order Example : HB - ZP - M 12 × 1000
Order Example: WA - ZP - M 12 - DIN 9021
Order Example: WA - ZP - M 12 - DIN 125
DIN
22
24
30
45
37
50
12
16
21
24
30
10/ 5
13/6,5
17/ 8
19/10
24/13
10
13
17
19
24
18
24
10
13
16
10/ 6
13/7,5
16/ 9,5
18/12
24/15,5
11,5
15,0
19,6
21,9
27,7
6,6
8,4
10,5
13,5
13
17
6,4
8,4
10,5
13
17
2
2
2,5
4
3
3
1,6
1,6
2
2,5
3
1000
1000
1000
1000
1000
2,2
4,0
6,4
12,9
17,3
M 6
M 8
M 10
M 12
M 16
M 6 x 12
M 6 x 25
M 8 x 25
M 8 x 40
M 10 x 20
M 10 x 30
M 10 x 45
M 10 x 60
M 10 x 70
M 12 x 22
M 12 x 25
M 12 x 30
M 12 x 40
M 12 x 50
M 12 x 60
M 12 x 80
M 12 x 90
M 16 x 40
M 16 x 60
M 16 x 90
M 8 x 25
M 10 x 30
M 10 x 45
M 12 x 25
M 12 x 30
M 12 x 40
M 12 x 60
M 12 x 80
M 16 x 40
M 16 x 60
M 16 x 90
M 6
M 8
M 10
M 12
M 16
M 6
M 8
M 10
M 12
M 16
440
9021
9021
440
9021
9021
M 6
M 8
M 10
M 12
M 12
M 16
M 6
M 8
M 10
M 12
M 16
M 8
M 10
M 12
M 16
M 6
M 8
M 10
M 12
M 16
M 6
M 8
M 10
M 12
M 16
Stainless SteelThread
Zinc PlatedThread - ZP
Stainless SteelThread
Stainless Steelfor bolt
Zinc Platedfor bolt - ZP
Stainless Steelfor bolt
Stainless SteelDimension
Material & Finishes Codes
( S. 53)
= h.d. galvanised, strength grade 4.6
= electroplated, 4.6
= , 8.8
= Stainless steel grade A4-50
strength grade
h.d. galvanised strength grade
= electroplated, strength grade 8.8
= Stainless steel grade A4-70
= Stainless steel grade A2-50
= Stainless steel grade A2-70
= Stainless steel W1.4529 HCR-50
fv
gv
fv 8.8
A4-50
gv 8.8
A4-70
A2-50
A2-70
HCR
e
S
S
m
S
d
D
S
d
D
Zinc PlatedThread - ZP
Zinc Platedfor bolt - ZP
Zinc PlatedDimension- ZP
D
[mm]
D
[mm]
S/mDIN
[mm]
SDIN
[mm]
S/mISO
[mm]
SEN
[mm]
e
[mm]
d
[mm]
d
[mm]
s
[mm]
s
[mm]
Length
[mm]
Load
cap.
[kN]
Threaded Rods, Hexagon Head Bol ts, Nuts, Washers
FR AMI NG SY STEM S ACC ESSORI ES
Order Example : TR - ZP - M 12 × 1000
Order Example : HB - ZP - M 12 × 1000
Order Example: WA - ZP - M 12 - DIN 9021
Order Example: WA - ZP - M 12 - DIN 125
DIN
22
24
30
45
37
50
12
16
21
24
30
10/ 5
13/6,5
17/ 8
19/10
24/13
10
13
17
19
24
18
24
10
13
16
10/ 6
13/7,5
16/ 9,5
18/12
24/15,5
11,5
15,0
19,6
21,9
27,7
6,6
8,4
10,5
13,5
13
17
6,4
8,4
10,5
13
17
2
2
2,5
4
3
3
1,6
1,6
2
2,5
3
1000
1000
1000
1000
1000
2,2
4,0
6,4
12,9
17,3
M 6
M 8
M 10
M 12
M 16
M 6 x 12
M 6 x 25
M 8 x 25
M 8 x 40
M 10 x 20
M 10 x 30
M 10 x 45
M 10 x 60
M 10 x 70
M 12 x 22
M 12 x 25
M 12 x 30
M 12 x 40
M 12 x 50
M 12 x 60
M 12 x 80
M 12 x 90
M 16 x 40
M 16 x 60
M 16 x 90
M 8 x 25
M 10 x 30
M 10 x 45
M 12 x 25
M 12 x 30
M 12 x 40
M 12 x 60
M 12 x 80
M 16 x 40
M 16 x 60
M 16 x 90
M 6
M 8
M 10
M 12
M 16
M 6
M 8
M 10
M 12
M 16
440
9021
9021
440
9021
9021
M 6
M 8
M 10
M 12
M 12
M 16
M 6
M 8
M 10
M 12
M 16
M 8
M 10
M 12
M 16
M 6
M 8
M 10
M 12
M 16
M 6
M 8
M 10
M 12
M 16
Stainless SteelThread
Zinc PlatedThread - ZP
Stainless SteelThread
Stainless Steelfor bolt
Zinc Platedfor bolt - ZP
Stainless Steelfor bolt
Stainless SteelDimension
Material & Finishes Codes
( S. 53)
= h.d. galvanised, strength grade 4.6
= electroplated, 4.6
= , 8.8
= Stainless steel grade A4-50
strength grade
h.d. galvanised strength grade
= electroplated, strength grade 8.8
= Stainless steel grade A4-70
= Stainless steel grade A2-50
= Stainless steel grade A2-70
= Stainless steel W1.4529 HCR-50
fv
gv
fv 8.8
A4-50
gv 8.8
A4-70
A2-50
A2-70
HCR
e
S
Zinc Plated Thread
Length(mm)
Load cap.(KN)
M6 2000/3000 2.2
M8 2000/3000 4.0
M10 2000/3000 6.4
M12 2000/3000 12.9
M16 2000/3000 17.3
Zinc Plated Thread
Length(mm)
d(mm)
M6 30-40 6.0
M8 30-40 8.0
M10 20-60 10.0
Order Example : STR - M 12
Order Example : STC - M 6
Order Example : SRB - M 6
Threaded Rod (STR)DIN 975
Square Washers SSW
H.D. Glavanized for Bolt
Stainless Steel for Bolt
a x b x d
(mm)M 6 M10 40 x 40 x (4-5-6)
M10 M12 40 x 40 x (4-5-6)
M12 M16 40 x 40 x (4-5-6)
FR AMI NG SY STEM S ACC ESSORI ES
s
L
D
L
Loadcap.
[kN]
Order example:
Order example:
Loadcap.
[kN]
S
[mm]
L
[mm]
D
[mm]
L
[mm]
10/10
12/14
13/16
16/20
21/25
26/32
13
17
22
15
20
25
30
40
50
40
40
50
2,2
4,0
6,4
9,3
17,3
27,0
6,4
9,3
17,3
M 6
M 8
M 10
M 12
M 16
M 20
M 10
M 12
M 16
M 6
M 8
M 10
M 12
M 16
M 20
M 10
M 12
M 16
CS - GV - M 16
HRC - GV - M 12
Coupler Sleeves, Square washers ,Sleeve Anchor ,Throught Anchor .......
Throught Anchor
Sleeve Anchor
b
da
b
d
a
Order Example: SW 41/41 - HDG - M 12
40 x 40 x 5
40 x 40 x 5
40 x 40 x 5
40 x 40 x 6
40 x 40 x 6
40 x 40 x 6
a x b x d
[mm]
M 10
M 12
M 16
M 6
M 10
M 12
M 6
M 10
M 12
M 10
M 12
M 16
ElectroplatedThread - GV
ElectroplatedThread - GV
Stainless SteelThread
Stainless SteelThread
H.D. Galvanisedfor Bolts - HDG
Stainless Steelfor Bolts
Yellow zinc plated SteelThread (Zn)
L (mm)
Order example:
M 6
M 8
M 10
M 12
45
50
60
74
M 6
M 8
M 10
STM - Zn - M 12
Stainless Steel
Thread
Drill
(mm)
10
12
15
18
Min.Drill hole
(mm)
55
60
75
90
M 6
M 8
M 10
Stainless Steel
Thread
Yellow zinc plated SteelThread (Zn)
Screwx Length (mm)
Order example:
M 6
M 8
M 10
M 12
6x50
8x60
10x80
12x90
STMH - Zn - M 12
S max fixing(mm)
5
10
20
25
Yellow zinc plated Steel Thread (Zn)
10
25
45
75
10.3
12.2
17.1
25.3
9.6
17.5
27.8
40.5
M 6
M 8
M 10
M 12
TypeMax Torque
(mm)Pull Out
Shear
8
19
38
9.5
14
19
8.4
15.4
24.4
Max Torque(mm)
Pull Out
Shear
Stainless SteelThread
Pull-out values in KN -concrete R 250kg/cm2
its is advisable to apply safty factor in consideration of the various ways of employment
(1KN=100kg)
Square Washers (SSW)
SSW 40/40for all channels 41/21 Series
SSW 41/41for all channels 41/41 Series
Order Example: SSW 41/41 - M 12 - d
round Washers DIN 440,DIN 9021
round Head machine Screws
DIN Zinc Plated
Stainless Steel
D
(mm)
d
(mm)
s
(mm)
440 M6 22 6.6 2
9021 M8 M8 24 8.4 2
9021 M10 M10 30 10.5 2.5
440 M12 45 13.5 4
9021 M12 M12 37 13 3
9021 M16 M16 50 17 3
Washers (SRW)DIN 440,DIN 9021
Round Head (SRH)DIN 7985
Order Example: SRW - M 12 - DIN 9021
Order Example: SRH - M 10 - DIN 7985
round Washers DIN 125
Washers (SRW)DIN 125
Zinc Plated
Stainless steel
D
(mm)
d
(mm)
s
(mm)M6 M6 12 6.4 1.6
M8 M8 16 8.4 1.6
M10 M10 21 10.5 2
M12 M12 24 13 2.5
M16 M16 30 17 3
Thread SizeM4x - y (mm)
M5x - y(mm)
M6x - y(mm)
M8x - y(mm)
Length 10 - 50 10 - 80 12 - 120 16 - 150
Order Example: SRW - M 12 -DIN 115
FR AMI NG SY STEM S ACC ESSORI ES
s
L
D
L
Loadcap.
[kN]
Order example:
Order example:
Loadcap.
[kN]
S
[mm]
L
[mm]
D
[mm]
L
[mm]
10/10
12/14
13/16
16/20
21/25
26/32
13
17
22
15
20
25
30
40
50
40
40
50
2,2
4,0
6,4
9,3
17,3
27,0
6,4
9,3
17,3
M 6
M 8
M 10
M 12
M 16
M 20
M 10
M 12
M 16
M 6
M 8
M 10
M 12
M 16
M 20
M 10
M 12
M 16
CS - GV - M 16
HRC - GV - M 12
Coupler Sleeves, Square washers ,Sleeve Anchor ,Throught Anchor .......
Throught Anchor
Sleeve Anchor
b
da
b
d
a
Order Example: SW 41/41 - HDG - M 12
40 x 40 x 5
40 x 40 x 5
40 x 40 x 5
40 x 40 x 6
40 x 40 x 6
40 x 40 x 6
a x b x d
[mm]
M 10
M 12
M 16
M 6
M 10
M 12
M 6
M 10
M 12
M 10
M 12
M 16
ElectroplatedThread - GV
ElectroplatedThread - GV
Stainless SteelThread
Stainless SteelThread
H.D. Galvanisedfor Bolts - HDG
Stainless Steelfor Bolts
Yellow zinc plated SteelThread (Zn)
L (mm)
Order example:
M 6
M 8
M 10
M 12
45
50
60
74
M 6
M 8
M 10
STM - Zn - M 12
Stainless Steel
Thread
Drill
(mm)
10
12
15
18
Min.Drill hole
(mm)
55
60
75
90
M 6
M 8
M 10
Stainless Steel
Thread
Yellow zinc plated SteelThread (Zn)
Screwx Length (mm)
Order example:
M 6
M 8
M 10
M 12
6x50
8x60
10x80
12x90
STMH - Zn - M 12
S max fixing(mm)
5
10
20
25
Yellow zinc plated Steel Thread (Zn)
10
25
45
75
10.3
12.2
17.1
25.3
9.6
17.5
27.8
40.5
M 6
M 8
M 10
M 12
TypeMax Torque
(mm)Pull Out
Shear
8
19
38
9.5
14
19
8.4
15.4
24.4
Max Torque(mm)
Pull Out
Shear
Stainless SteelThread
Pull-out values in KN -concrete R 250kg/cm2
its is advisable to apply safty factor in consideration of the various ways of employment
(1KN=100kg)
S
m
S
d
D
S
d
D
Zinc PlatedThread - ZP
Zinc Platedfor bolt - ZP
Zinc PlatedDimension- ZP
D
[mm]
D
[mm]
S/mDIN
[mm]
SDIN
[mm]
S/mISO
[mm]
SEN
[mm]
e
[mm]
d
[mm]
d
[mm]
s
[mm]
s
[mm]
Length
[mm]
Load
cap.
[kN]
Threaded Rods, Hexagon Head Bol ts, Nuts, Washers
FR AMI NG SY STEM S ACC ESSORI ES
Order Example : TR - ZP - M 12 × 1000
Order Example : HB - ZP - M 12 × 1000
Order Example: WA - ZP - M 12 - DIN 9021
Order Example: WA - ZP - M 12 - DIN 125
DIN
22
24
30
45
37
50
12
16
21
24
30
10/ 5
13/6,5
17/ 8
19/10
24/13
10
13
17
19
24
18
24
10
13
16
10/ 6
13/7,5
16/ 9,5
18/12
24/15,5
11,5
15,0
19,6
21,9
27,7
6,6
8,4
10,5
13,5
13
17
6,4
8,4
10,5
13
17
2
2
2,5
4
3
3
1,6
1,6
2
2,5
3
1000
1000
1000
1000
1000
2,2
4,0
6,4
12,9
17,3
M 6
M 8
M 10
M 12
M 16
M 6 x 12
M 6 x 25
M 8 x 25
M 8 x 40
M 10 x 20
M 10 x 30
M 10 x 45
M 10 x 60
M 10 x 70
M 12 x 22
M 12 x 25
M 12 x 30
M 12 x 40
M 12 x 50
M 12 x 60
M 12 x 80
M 12 x 90
M 16 x 40
M 16 x 60
M 16 x 90
M 8 x 25
M 10 x 30
M 10 x 45
M 12 x 25
M 12 x 30
M 12 x 40
M 12 x 60
M 12 x 80
M 16 x 40
M 16 x 60
M 16 x 90
M 6
M 8
M 10
M 12
M 16
M 6
M 8
M 10
M 12
M 16
440
9021
9021
440
9021
9021
M 6
M 8
M 10
M 12
M 12
M 16
M 6
M 8
M 10
M 12
M 16
M 8
M 10
M 12
M 16
M 6
M 8
M 10
M 12
M 16
M 6
M 8
M 10
M 12
M 16
Stainless SteelThread
Zinc PlatedThread - ZP
Stainless SteelThread
Stainless Steelfor bolt
Zinc Platedfor bolt - ZP
Stainless Steelfor bolt
Stainless SteelDimension
Material & Finishes Codes
( S. 53)
= h.d. galvanised, strength grade 4.6
= electroplated, 4.6
= , 8.8
= Stainless steel grade A4-50
strength grade
h.d. galvanised strength grade
= electroplated, strength grade 8.8
= Stainless steel grade A4-70
= Stainless steel grade A2-50
= Stainless steel grade A2-70
= Stainless steel W1.4529 HCR-50
fv
gv
fv 8.8
A4-50
gv 8.8
A4-70
A2-50
A2-70
HCR
e
S
S
m
S
d
D
S
d
D
Zinc PlatedThread - ZP
Zinc Platedfor bolt - ZP
Zinc PlatedDimension- ZP
D
[mm]
D
[mm]
S/mDIN
[mm]
SDIN
[mm]
S/mISO
[mm]
SEN
[mm]
e
[mm]
d
[mm]
d
[mm]
s
[mm]
s
[mm]
Length
[mm]
Load
cap.
[kN]
Threaded Rods, Hexagon Head Bol ts, Nuts, Washers
FR AMI NG SY STEM S ACC ESSORI ES
Order Example : TR - ZP - M 12 × 1000
Order Example : HB - ZP - M 12 × 1000
Order Example: WA - ZP - M 12 - DIN 9021
Order Example: WA - ZP - M 12 - DIN 125
DIN
22
24
30
45
37
50
12
16
21
24
30
10/ 5
13/6,5
17/ 8
19/10
24/13
10
13
17
19
24
18
24
10
13
16
10/ 6
13/7,5
16/ 9,5
18/12
24/15,5
11,5
15,0
19,6
21,9
27,7
6,6
8,4
10,5
13,5
13
17
6,4
8,4
10,5
13
17
2
2
2,5
4
3
3
1,6
1,6
2
2,5
3
1000
1000
1000
1000
1000
2,2
4,0
6,4
12,9
17,3
M 6
M 8
M 10
M 12
M 16
M 6 x 12
M 6 x 25
M 8 x 25
M 8 x 40
M 10 x 20
M 10 x 30
M 10 x 45
M 10 x 60
M 10 x 70
M 12 x 22
M 12 x 25
M 12 x 30
M 12 x 40
M 12 x 50
M 12 x 60
M 12 x 80
M 12 x 90
M 16 x 40
M 16 x 60
M 16 x 90
M 8 x 25
M 10 x 30
M 10 x 45
M 12 x 25
M 12 x 30
M 12 x 40
M 12 x 60
M 12 x 80
M 16 x 40
M 16 x 60
M 16 x 90
M 6
M 8
M 10
M 12
M 16
M 6
M 8
M 10
M 12
M 16
440
9021
9021
440
9021
9021
M 6
M 8
M 10
M 12
M 12
M 16
M 6
M 8
M 10
M 12
M 16
M 8
M 10
M 12
M 16
M 6
M 8
M 10
M 12
M 16
M 6
M 8
M 10
M 12
M 16
Stainless SteelThread
Zinc PlatedThread - ZP
Stainless SteelThread
Stainless Steelfor bolt
Zinc Platedfor bolt - ZP
Stainless Steelfor bolt
Stainless SteelDimension
Material & Finishes Codes
( S. 53)
= h.d. galvanised, strength grade 4.6
= electroplated, 4.6
= , 8.8
= Stainless steel grade A4-50
strength grade
h.d. galvanised strength grade
= electroplated, strength grade 8.8
= Stainless steel grade A4-70
= Stainless steel grade A2-50
= Stainless steel grade A2-70
= Stainless steel W1.4529 HCR-50
fv
gv
fv 8.8
A4-50
gv 8.8
A4-70
A2-50
A2-70
HCR
e
S
Zinc Plated (E)
H.D. Glavanized
Grade 4.6
(E)
Head (A) mm
Head (H) mm
Square Width (O) mm
Square Depth (P) mm
M5 M5 12.0 3.0 5.0 3.2
M6 M6 15.1 3.70 6.40 4.0
M8 M8 18.3 4.50 8.23 4.75
M10 M10 21.44 5.30 9.86 5.56
M16 M16 34.14 8.74 16.3 8.74
HP
E
O
A
Carriage bolts (STC)
Roofing bolts(SRB)
ww
w.u
nim
etal
-ikk.
com
Cable maNaGemeNt SyStemSCable tray SyStemS
www.unimetal-ikk.com42
Coupler Sleeves rounded
Coupler Sleeves (SCS)Electroplated Thread Stainless Steel Thread
D
(mm)
L
(mm)
Loadcap.
(KN)
M6 M6 10/10 15 2.2
M8 M8 12/14 20 4.0
M10 M10 13/16 25 6.4
M12 M12 16/20 30 9.3
M16 M16 21/25 40 17.3
M20 M20 26/32 50 27.0
Order Example: SCS - M 16
Hexagonal Rod Coupler
Hexagonal Rod Coupler with view hole (SHR) Electroplated Thread Stainless Steel Thread
S
(mm)
L
(mm)
Loadcap.
(KN)
M10 M10 13 40 6.4
M12 M12 17 40 9.3
M16 M16 22 50 17.3
Order Example: SHR - M 12
Hexagon Nuts DIN 934, DIN EN 24032
S
m
S
d
D
S
d
D
Zinc PlatedThread - ZP
Zinc Platedfor bolt - ZP
Zinc PlatedDimension- ZP
D
[mm]
D
[mm]
S/mDIN
[mm]
SDIN
[mm]
S/mISO
[mm]
SEN
[mm]
e
[mm]
d
[mm]
d
[mm]
s
[mm]
s
[mm]
Length
[mm]
Load
cap.
[kN]
Threaded Rods, Hexagon Head Bol ts, Nuts, Washers
FR AMI NG SY STEM S ACC ESSORI ES
Order Example : TR - ZP - M 12 × 1000
Order Example : HB - ZP - M 12 × 1000
Order Example: WA - ZP - M 12 - DIN 9021
Order Example: WA - ZP - M 12 - DIN 125
DIN
22
24
30
45
37
50
12
16
21
24
30
10/ 5
13/6,5
17/ 8
19/10
24/13
10
13
17
19
24
18
24
10
13
16
10/ 6
13/7,5
16/ 9,5
18/12
24/15,5
11,5
15,0
19,6
21,9
27,7
6,6
8,4
10,5
13,5
13
17
6,4
8,4
10,5
13
17
2
2
2,5
4
3
3
1,6
1,6
2
2,5
3
1000
1000
1000
1000
1000
2,2
4,0
6,4
12,9
17,3
M 6
M 8
M 10
M 12
M 16
M 6 x 12
M 6 x 25
M 8 x 25
M 8 x 40
M 10 x 20
M 10 x 30
M 10 x 45
M 10 x 60
M 10 x 70
M 12 x 22
M 12 x 25
M 12 x 30
M 12 x 40
M 12 x 50
M 12 x 60
M 12 x 80
M 12 x 90
M 16 x 40
M 16 x 60
M 16 x 90
M 8 x 25
M 10 x 30
M 10 x 45
M 12 x 25
M 12 x 30
M 12 x 40
M 12 x 60
M 12 x 80
M 16 x 40
M 16 x 60
M 16 x 90
M 6
M 8
M 10
M 12
M 16
M 6
M 8
M 10
M 12
M 16
440
9021
9021
440
9021
9021
M 6
M 8
M 10
M 12
M 12
M 16
M 6
M 8
M 10
M 12
M 16
M 8
M 10
M 12
M 16
M 6
M 8
M 10
M 12
M 16
M 6
M 8
M 10
M 12
M 16
Stainless SteelThread
Zinc PlatedThread - ZP
Stainless SteelThread
Stainless Steelfor bolt
Zinc Platedfor bolt - ZP
Stainless Steelfor bolt
Stainless SteelDimension
Material & Finishes Codes
( S. 53)
= h.d. galvanised, strength grade 4.6
= electroplated, 4.6
= , 8.8
= Stainless steel grade A4-50
strength grade
h.d. galvanised strength grade
= electroplated, strength grade 8.8
= Stainless steel grade A4-70
= Stainless steel grade A2-50
= Stainless steel grade A2-70
= Stainless steel W1.4529 HCR-50
fv
gv
fv 8.8
A4-50
gv 8.8
A4-70
A2-50
A2-70
HCR
e
S
Hexagon nut (SHN)DIN 934 or ISO 4032(= DIN EN 24032)
Zinc Plated Thread Stainless Steel ThreadS/mDIN
(mm)
S/mISO
(mm)
e
(mm)
M6 M6 10/5 10/6 11.5
M8 M8 13/6.5 13/7.5 15.0
M10 M10 17/8 16/9.5 19.6
M12 M12 19/10 18/12 21.9
M16 M16 24/13 24/15.5 27.7
machine HexHead bolts DIN 933, DIN 24017
S
m
S
d
D
S
d
D
Zinc PlatedThread - ZP
Zinc Platedfor bolt - ZP
Zinc PlatedDimension- ZP
D
[mm]
D
[mm]
S/mDIN
[mm]
SDIN
[mm]
S/mISO
[mm]
SEN
[mm]
e
[mm]
d
[mm]
d
[mm]
s
[mm]
s
[mm]
Length
[mm]
Load
cap.
[kN]
Threaded Rods, Hexagon Head Bol ts, Nuts, Washers
FR AMI NG SY STEM S ACC ESSORI ES
Order Example : TR - ZP - M 12 × 1000
Order Example : HB - ZP - M 12 × 1000
Order Example: WA - ZP - M 12 - DIN 9021
Order Example: WA - ZP - M 12 - DIN 125
DIN
22
24
30
45
37
50
12
16
21
24
30
10/ 5
13/6,5
17/ 8
19/10
24/13
10
13
17
19
24
18
24
10
13
16
10/ 6
13/7,5
16/ 9,5
18/12
24/15,5
11,5
15,0
19,6
21,9
27,7
6,6
8,4
10,5
13,5
13
17
6,4
8,4
10,5
13
17
2
2
2,5
4
3
3
1,6
1,6
2
2,5
3
1000
1000
1000
1000
1000
2,2
4,0
6,4
12,9
17,3
M 6
M 8
M 10
M 12
M 16
M 6 x 12
M 6 x 25
M 8 x 25
M 8 x 40
M 10 x 20
M 10 x 30
M 10 x 45
M 10 x 60
M 10 x 70
M 12 x 22
M 12 x 25
M 12 x 30
M 12 x 40
M 12 x 50
M 12 x 60
M 12 x 80
M 12 x 90
M 16 x 40
M 16 x 60
M 16 x 90
M 8 x 25
M 10 x 30
M 10 x 45
M 12 x 25
M 12 x 30
M 12 x 40
M 12 x 60
M 12 x 80
M 16 x 40
M 16 x 60
M 16 x 90
M 6
M 8
M 10
M 12
M 16
M 6
M 8
M 10
M 12
M 16
440
9021
9021
440
9021
9021
M 6
M 8
M 10
M 12
M 12
M 16
M 6
M 8
M 10
M 12
M 16
M 8
M 10
M 12
M 16
M 6
M 8
M 10
M 12
M 16
M 6
M 8
M 10
M 12
M 16
Stainless SteelThread
Zinc PlatedThread - ZP
Stainless SteelThread
Stainless Steelfor bolt
Zinc Platedfor bolt - ZP
Stainless Steelfor bolt
Stainless SteelDimension
Material & Finishes Codes
( S. 53)
= h.d. galvanised, strength grade 4.6
= electroplated, 4.6
= , 8.8
= Stainless steel grade A4-50
strength grade
h.d. galvanised strength grade
= electroplated, strength grade 8.8
= Stainless steel grade A4-70
= Stainless steel grade A2-50
= Stainless steel grade A2-70
= Stainless steel W1.4529 HCR-50
fv
gv
fv 8.8
A4-50
gv 8.8
A4-70
A2-50
A2-70
HCR
e
S
Hex Head Bolt (SHB)DIN 933 or EN 24017(without nut)
Order Example : SHB - M 12
Zinc Plated Dimension Stainless Steel DimensionS
DIN(mm)
SEN
(mm)
M 6 x 1210 10
M 6 x 25
M 8 x 25 M 8 x 2513 13
M 8 x 40
M 10 x 20
17 16
M 10 x 30 M 10 x 30
M 10 x 45 M 10 x 45
M 10 x 60
M 10 x 70
M 12 x 22
19 18
M 12 x 25 M 12 x 25
M 12 x 30 M 12 x 30
M 12 x 40 M 12 x 40
M 12 x 50
M 12 x 60 M 12 x 60
M 12 x 80 M 12 x 80
M 12 x 90
M 16 x 40 M 16 x 40
24 24M 16 x 60 M 16 x 60
M 16 x 90 M 16 x 90
Order Example : SHN - M 12
Cable tray Support System- C - Channel- Cantilever Arm- U - Support- I - Support
- Wall bracket- Support accessories
43
Cable maNaGemeNt SyStemSCable tray SyStemS
www.unimetal-ikk.com44
- C-Channel Systems
ChannelUni-metal’s framing channel is cold formed on modern rolling machines from low carbon steel strips. A continuous slot provides the ability to make attachments at any point.
LengthsStandard length: 3000 mm with ± 3.2mm length tolerance. Custom lengths are available upon request.
Z
Z
YY
Z
Z
YY
Z
Z
YY
Z
Z
Y Y
21.07.0
41.0
21.0
41.0
22.0
42.0
7.0
41.0
22.0
41.0
7.0
41.0
41.0
41.0
22.0
82.0
7.0
41.0
22.0
50
30
13
Z
Z
YY
Z
Z
YY
Z
Z
YY
Z
Z
Y Y
21.07.0
41.0
21.0
41.0
22.0
42.0
7.0
41.0
22.0
41.0
7.0
41.0
41.0
41.0
22.0
82.0
7.0
41.0
22.0
50
30
13
Z
Z
YY
Z
Z
YY
Z
Z
YY
Z
Z
Y Y
21.07.0
41.0
21.0
41.0
22.0
42.0
7.0
41.0
22.0
41.0
7.0
41.0
41.0
41.0
22.0
82.0
7.0
41.0
22.0
50
30
13
Z
Z
YY
Z
Z
YY
Z
Z
YY
Z
Z
Y Y
21.07.0
41.0
21.0
41.0
22.0
42.0
7.0
41.0
22.0
41.0
7.0
41.0
41.0
41.0
22.0
82.0
7.0
41.0
22.0
50
30
13
Z
Z
YY
Z
Z
YY
Z
Z
YY
Z
Z
Y Y
21.07.0
41.0
21.0
41.0
22.0
42.0
7.0
41.0
22.0
41.0
7.0
41.0
41.0
41.0
22.0
82.0
7.0
41.0
22.0
50
30
13
Channel Hole Patterns
Metal Framing ChannelsSelection Chart
PT Plain Type ST Slotted Type B2B Type
Part No Channel Dimensions Thickness
Height “H” Width “W”
CCH - 220/221 21.0 mm 41.0 mm 1.5 mm
CCH - 240/241 41.0 mm 41.0 mm 1.5 mm
CCH - 320/321 21.0 mm 41.0 mm 2.0 mm
CCH - 340/341 41.0 mm 41.0 mm 2.0 mm
CCH - 420/421 21.0 mm 41.0 mm 2.5 mm
CCH - 440/441 41.0 mm 41.0 mm 2.5 mm
CCH 320 3 2 0
Channel Patterns0 - PT 1 - ST2 - B2B
Size2 - 21/41 mm 4 - 41/41 mm
Material Thickness2 for 1.5 mm3 for 2.0 mm 4 for 2.5 mm
For more information on Uni-channel Systems , Uni-Metal technical staff will be ready to assist you with all necessary details. www.unimetal-ikk.com
Cab
le t
ray
SyS
tem
S
45
A
* Given Loads are always in [kN] “ Allowable characteristic live load “
A
base plate : height (h) x width (b) x thickness (t) 140 50 10 •In the case of concrete support frame, use anchor M20 .•In the case of concrete C-channel frame, use spring nut M16 .
** Connection force (pull-out force) : 8.8 (KN)
F1
1/2 A 1/2 A
or F2
Length A (mm)
h
2525
h-50
b t
FD
Fz
Fv =F1 + F2
base plate : height (h) x width (b) x thickness (t) 110 50 8
•In the case of concrete support frame, use anchor M16 .•In the case of concrete C-channel frame, use spring nut M12 .** Connection force (pull-out force) : 5.13 (KN)
1.20
1.40
0.20
0.40
0.60
0.80
1.00
0.00
F2F1
A(mm)
F 1 o
r F 2
in
KN
0.0
1.0
2.0
3.0
4.0
5.0
6.0
0.0
2.0
4.0
6.0
8.0
10.0
12.0
F2F1
A(mm)
F 1 o
r F2
in K
N
Length Allowable LoadA (mm) F1* F2* Fz**
150 1.30 0.64 5.13
300 0.64 0.32 5.13
450 0.43 0.21 5.13
600 0.32 0.16 5.13
700 0.27 0.14 5.13
800 0.24 0.12 5.13
900 0.21 0.11 5.13
1000 0.19 0.10 5.13
Length Allowable LoadA (mm) F1* F2* Fz**
150 5.18 2.65 8.8
300 2.70 1.25 8.8
450 1.80 0.90 8.8
600 1.35 0.65 8.8
700 1.15 0.55 8.8
800 0.95 0.45 8.8
900 0.90 0.40 8.8
1000 0.75 0.35 8.8
Cantilever Arm Brackets - SCA
- CCH421 41x21x2.5
- CCH441 41x41x2.5
Cantilever Arm Bracket
ww
w.u
nim
etal
-ikk.
com
Cable maNaGemeNt SyStemSCable tray SyStemS
www.unimetal-ikk.com46
A
base plate : height (h) x width (b) x thickness (t) 130 50 10
•In the case of concrete support frame, use anchor M12.•In the case of concrete C-channel frame, use spring nut M8. ** Connection force (pull-out force) : 8.48 (KN)
3.00
3.50
0.50
1.00
1.50
2.00
2.50
0.00
F2F1
F 1 /
F 2 i
n K
N
A
* Given Loads are always in [kN] “ Allowable characteristic live load “
F1
1/2 A 1/2 A
or F2
Length A (mm)
h
b t
2525
h-50
FD
Fv =F1 + F2
Fz
base plate : height (h) x width (b) x thickness (t) 180 50 10
•In the case of concrete support frame, use anchor M16.•In the case of concrete C-channel frame, use spring nut M12 .** Connection force (pull-out force) : 14.7 (KN)
0.0
1.0
2.0
3.0
4.0
5.0
6.0
0.0
2.0
4.0
6.0
8.0
10.0
12.0
F2F1
F 1 /
F 2 i
n K
N
A(mm)
Length Allowable LoadA (mm) F1* F2* Fz**
150 3.10 1.50 8.48
300 1.50 0.80 8.48
450 1.00 0.51 8.48
600 0.80 0.38 8.48
700 0.66 0.33 8.48
800 0.57 0.29 8.48
900 0.51 0.26 8.48
1000 0.46 0.23 8.48
Length Allowable LoadA (mm) F1* F2* Fz**
150 11.0 6.7 14.7
300 6.50 3.50 14.7
450 4.60 2.35 14.7
600 3.50 1.75 14.7
700 3.00 1.50 14.7
800 2.65 1.30 14.7
900 2.35 1.15 14.7
1000 2.10 1.00 14.7
- CCH422 41x21x2.5 b2b
- CCH442 41x41x2.5 b2b
Cab
le t
ray
SyS
tem
S
47
- U - Support 3000
- I - Support 3050
- Wall bracket 3200 - 3250
200140
100
8042
25
70
200140
100
8042
25
70
13x30
13x30
13x30
13x30
5
5
200140
100
8042
25
70
200140
100
8042
25
70
13x30
13x30
13x30
13x30
5
5
200140
100
8042
25
70
200140
100
8042
25
70
13x30
13x30
13x30
13x30
5
53000
3050
3200 3250
Order Example: 3000 - Length (L) - Thickness (t) for more ordering details, please check pages (61-62)
U-Support with welded-on head plate200 x 100 x 5mm
U-Support with welded-on head plate200 x 100 x 5mm
5 mm thickness
for U-Support for I-Support
Order Example: 3050 - Length (L) - Thickness (t) for more ordering details, please check pages (61-62)
Order Example: 3200 - Length (L) - Thickness (t) for more ordering details, please check pages (61-62)
Order example Item (L) (t)
3000 0200 5
Order example Item (L) (t)
3050 0200 5
Order example Item (L) (t)
3200 0210 5
- Head Plate 3100
3100
200 x 100 x 5mm
Cable tray Support System
Cable maNaGemeNt SyStemSCable tray SyStemS
www.unimetal-ikk.com48
- Support connectors 3300
- Support plates 3400 - Clamping angles
3550
- Angles 3600
- Clamping plates 3350
- Support clamps 3450
3300
3400 3550
3600
3450
3350
Order Example: 3300 - Length (L) - Thickness (t) for more ordering details, please check pages (61-62)
Order Example: 3350 - Length (L) - Thickness (t) for more ordering details, please check pages (61-62)
Order example Item (L) (t)
3300 0200 5
Order example Item (L) (t)
3350 0200 5
Cab
le t
ray
SyS
tem
S
49
Heavy Duty anchors- expansion Steel anchor - Stm
- Drop-in anchor - SDa
- Sleeve anchor - SaS / Sab
- Through Bolt (Wedge Anchor) - Stb
- Shield anchor - SSa
Cable maNaGemeNt SyStemSCable tray SyStemS
50
HeaVy DUty aNCHOrS General Information
Fig.1
Fig.2
Fig.3
Fig.4
Fig.4
Fig.3
Fig.2
Fig.1
Direction of Loading
The direction of the applied load shall be considered to determine the most appropriate anchor . The tension and shear components shall be lesser than the recommended load/design resistance in the direction concerned.
tensile loadsTensile loads are applied along the axis of fixing (see Fig.1).Common examples include suspended ceiling applications and the suspension of mechanical services, pipework , ductwork ,etc ...
Shear loadsShear loads act at right angles to the axis of fixing and directly against the face of the structural material (see Fig.2).Shear performance is governed mainly by the shear strength of the bolt material and by the comperssive strength of the supporting substrate.
Oblique / Combined LoadsOblique loads are a combination of tension and shear components (see Fig.3).If the angle of the applied oblique load is within 10˚ of pure tension or pure shear, the safe working load for that direction may be assumed. Otherwise, the applied oblique load shall be resolved into its shear and tensile components.
Offset LoadsOffset loads act at right angles to the fixing axis but are offset from the surface (see Fig.4).In this situation, the deflection of the bolt due to bending needs to be considered as well as the shear capacity of the anchor.
Slotted Holes in FixtureWhen fixing anchors through slotted holes; it is important to ensure that there is an adequate surface of contact between the washer and the fixture to guarantee a positive clamping force.If in doubt, a square plate washer with a thickness of 3mm or above would be recommended in place of the standard washer supplied.
Diamond Drilled Holes When holes are formed in the structure using a diamond drilling system; extra care is required to ensure the holes are thoroughly cleaned by brushing and blowing for at least three times. Also, to make a key for the anchor (particulary if a bonded anchor is installed) the sides of the hole shall be roughened up by inserting a standard masonry bit into the hole attached to a hammer action drilling machine.A resin with minimal shrinkage shall be selected for diamond drilled holes.
Cab
le t
ray
SyS
tem
S
51
Heavy Duty anchors
expansion Steel anchor - Stm
Features:- Suitable for all screws or threaded bolts with metric thread.- Low energy impact, power-saving assembly.- Multiple removing and fixing.- Inside threaded anchor, allows great flexibility.- Can use variable lengths and art of threaded rods or bolts.- Small edge distance and small distance between anchors.- Provide uniform load by tightening the screw or hexagon nut, the cone pulls into the expansion anchor and tightens against the drilled hole. - Suitable for use in concrete and natural stone.
Typical Applications:Cable trays, handrails, brackets, staircases, ladders, machines, window panels, base plates, scaffoldings and frameworks .
FR AMI NG SY STEM S ACC ESSORI ES
s
L
D
L
Loadcap.
[kN]
Order example:
Order example:
Loadcap.
[kN]
S
[mm]
L
[mm]
D
[mm]
L
[mm]
10/10
12/14
13/16
16/20
21/25
26/32
13
17
22
15
20
25
30
40
50
40
40
50
2,2
4,0
6,4
9,3
17,3
27,0
6,4
9,3
17,3
M 6
M 8
M 10
M 12
M 16
M 20
M 10
M 12
M 16
M 6
M 8
M 10
M 12
M 16
M 20
M 10
M 12
M 16
CS - GV - M 16
HRC - GV - M 12
Coupler Sleeves, Square washers ,Sleeve Anchor ,Throught Anchor .......
Throught Anchor
Sleeve Anchor
b
da
b
d
a
Order Example: SW 41/41 - HDG - M 12
40 x 40 x 5
40 x 40 x 5
40 x 40 x 5
40 x 40 x 6
40 x 40 x 6
40 x 40 x 6
a x b x d
[mm]
M 10
M 12
M 16
M 6
M 10
M 12
M 6
M 10
M 12
M 10
M 12
M 16
ElectroplatedThread - GV
ElectroplatedThread - GV
Stainless SteelThread
Stainless SteelThread
H.D. Galvanisedfor Bolts - HDG
Stainless Steelfor Bolts
Yellow zinc plated SteelThread (Zn)
L (mm)
Order example:
M 6
M 8
M 10
M 12
45
50
60
74
M 6
M 8
M 10
STM - Zn - M 12
Stainless Steel
Thread
Drill
(mm)
10
12
15
18
Min.Drill hole
(mm)
55
60
75
90
M 6
M 8
M 10
Stainless Steel
Thread
Yellow zinc plated SteelThread (Zn)
Screwx Length (mm)
Order example:
M 6
M 8
M 10
M 12
6x50
8x60
10x80
12x90
STMH - Zn - M 12
S max fixing(mm)
5
10
20
25
Yellow zinc plated Steel Thread (Zn)
10
25
45
75
10.3
12.2
17.1
25.3
9.6
17.5
27.8
40.5
M 6
M 8
M 10
M 12
TypeMax Torque
(mm)Pull Out
Shear
8
19
38
9.5
14
19
8.4
15.4
24.4
Max Torque(mm)
Pull Out
Shear
Stainless SteelThread
Pull-out values in KN -concrete R 250kg/cm2
its is advisable to apply safty factor in consideration of the various ways of employment
(1KN=100kg)
STM/H
FR AMI NG SY STEM S ACC ESSORI ES
s
L
D
L
Loadcap.
[kN]
Order example:
Order example:
Loadcap.
[kN]
S
[mm]
L
[mm]
D
[mm]
L
[mm]
10/10
12/14
13/16
16/20
21/25
26/32
13
17
22
15
20
25
30
40
50
40
40
50
2,2
4,0
6,4
9,3
17,3
27,0
6,4
9,3
17,3
M 6
M 8
M 10
M 12
M 16
M 20
M 10
M 12
M 16
M 6
M 8
M 10
M 12
M 16
M 20
M 10
M 12
M 16
CS - GV - M 16
HRC - GV - M 12
Coupler Sleeves, Square washers ,Sleeve Anchor ,Throught Anchor .......
Throught Anchor
Sleeve Anchor
b
da
b
d
a
Order Example: SW 41/41 - HDG - M 12
40 x 40 x 5
40 x 40 x 5
40 x 40 x 5
40 x 40 x 6
40 x 40 x 6
40 x 40 x 6
a x b x d
[mm]
M 10
M 12
M 16
M 6
M 10
M 12
M 6
M 10
M 12
M 10
M 12
M 16
ElectroplatedThread - GV
ElectroplatedThread - GV
Stainless SteelThread
Stainless SteelThread
H.D. Galvanisedfor Bolts - HDG
Stainless Steelfor Bolts
Yellow zinc plated SteelThread (Zn)
L (mm)
Order example:
M 6
M 8
M 10
M 12
45
50
60
74
M 6
M 8
M 10
STM - Zn - M 12
Stainless Steel
Thread
Drill
(mm)
10
12
15
18
Min.Drill hole
(mm)
55
60
75
90
M 6
M 8
M 10
Stainless Steel
Thread
Yellow zinc plated SteelThread (Zn)
Screwx Length (mm)
Order example:
M 6
M 8
M 10
M 12
6x50
8x60
10x80
12x90
STMH - Zn - M 12
S max fixing(mm)
5
10
20
25
Yellow zinc plated Steel Thread (Zn)
10
25
45
75
10.3
12.2
17.1
25.3
9.6
17.5
27.8
40.5
M 6
M 8
M 10
M 12
TypeMax Torque
(mm)Pull Out
Shear
8
19
38
9.5
14
19
8.4
15.4
24.4
Max Torque(mm)
Pull Out
Shear
Stainless SteelThread
Pull-out values in KN -concrete R 250kg/cm2
its is advisable to apply safty factor in consideration of the various ways of employment
(1KN=100kg)
STMExpansion Steel Anchor
technical Data:Recommended loads (non-concreted C 20/25).
Setting Data:Edge distance > 1,5 x H eff., distance between anchors > 3 x H eff. Thickness of foundation > 2 x H eff.
Installation Parmeters:H eff = Effective anchorage depth.
Type(order No)
Tension Load(KN)
Shear Load(KN)
Bending Moment(Nm)
Screw Grade
M6 2.5 2.3 3.9 8.8
M8 3.3 4.4 17 8.8
M10 4.7 6.5 34 8.8
M12 6.9 8.5 60 8.8
Size H eff.(mm)
Edge DistanceC (mm)
Distance BetweenAnchors S (mm)
Thickness ofFoundationhmin (mm)
Washer(Ø)
Tightening Torque (Nm)
Spannersize (mm)
M6 40 60 120 100 12 x 1.6 10 10
M8 45 68 135 100 16 x 1.6 20 13
M10 55 83 165 110 20 x 2.0 40 17
M12 70 105 210 140 24 x 2.5 75 19
Bolt Size Length exp.unit
(mm)
Drill (Ø) (mm)
Drilling depth (mm)
H eff.(mm)
Usable Length(mm)
Screw Ø x Length (mm)
M6 45 10 55 40 5 M6 x 50
M8 50 12 60 45 10 M8 x 60
M10 60 15 80 55 20 M10 x 80
M12 75 18 90 70 25 M12 x 90H eff
Thickness of Foundation
Length
Washer
MSpaner
Size
Drilling depth
Usable Length
AHM Sleeve Anchor serutaeF
secnatsidecapsdnaegdellamSTorque controlled expansionZinc plated > 5µmThrough xing
Applications snoitcurtsnoc-rednu,selorp,senihcam,snoitcurtsnocleets
noitallatsnI
S-AHM Sleeve Anchor with hexagon screw htgneLmmØllirDmm
htpedgnillirDdaerhTmm
htgnelelbasUmm
htpedgnitteSmin.mm
6M6M8M8M01M01M
B-AHM Sleeve Anchor with threaded bolt and nut
58 Mungo Befestigungstechnik AG
Met
al P
rodu
cts
kat_en-2007-11-29.indd 58 4.12.2007 10:13:36 Uhr
Tension load (kN)
Type(Order No)
Shear load (kN)
Bending moment (Nm)
Distance betweenanchor S (mm)
6M8M01M21M
2.03.05.0
5.7
105120150225
Min. thickness of found
(hmin) mm
Tighten torque(Nm)
Spannersize (SAS)
Spannersize (SAB)
Drill Ø(mm)
Size(mm)
Length(mm)
Usablelength(mm)
Drilling depth(mm)
Settingdepth min.
(mm)88
10101212
M6M6M8M8
M10M10
4560608070
100
555560607070
51515251535
353540405050
Drill Ø(mm)
Size(mm)
Length(mm)
Usablelength(mm)
Drilling depth(mm)
Settingdepth min.
(mm)88
101010121212161616
M6M6M8M8M8
M10M10M10M12M12M12
406550759575
10013065
110145
5555606060707070909090
5255
30501540705
2560
3535404040505050757575
Plug & drill Ø(mm)
Length(mm)
UsableDrilling Depth(mm)
Length(mm)
SettingDepth Min.
(mm)5406060807001
555506060707
55151525153
535304040505
8801012121
2.53.35.58.0
90.0100.0120.0140.0
10.013.017.0---
10.013.015.019.0
8.025.040.050.0
4.205.30
12.8025.0
Distance to edge C (mm)
55.060.075.0
115.0
Tinst
materials:- zinc plated steel.- stainless steel [ SS 304 (A2) , SS 316 (A4) ].
*for cracked Concrete we shall use 0,5 x this value (approximately)
Installation
Throughbolt, stainless steel A4/316
serutaeFetercnocdekcarcnurof7noitpOlavorppAlacinhceTnaeporuE
Torque controlled expansionApplications in damp areas and outdoorsStainless steel A4/316Face xing or through xing
Applications ,senihcam,snoitcurtsnocleets,sgniliar,syartelbac,sedacaf
under-constructions, high-racks, pro les
Tension load (kN)
Shear load (kN)
Bending moment (Nm)
Edge Distance C (mm)
He�. (mm)
Distance betweenanchor S (mm)
Thickness offoundation
(mm)
Tighten torque(Nm)
Spanner size
6M 2.64.15.89.214
3.36.38.51223
5153050
100
5.513
26.546.5
118.5
4050586880
Washer (Ø)
12 x 1.616 x 1.620 x 2.024 x 2.530 x 3.0
02106 001 018M 05157 001 3101M 47178 021 7121M 402201 041 9161M 042021 061 42
noitallatsnI
2
03505604015660452086040459672505803010680501088055158805525980554511833506015301070185515901850301101855452101850604101850806101850010810194508218651011218603521218605541218607561218609581210701511610851031610803541610854061610856081610010306102
50 Mungo Befestigungstechnik AG
Plug & drill Ø(mm)
Length(mm)
UsableLength(mm)
Settingdepth min.
(mm)
kat_en-2007-11-29.indd 50 4.12.2007 10:12:24 Uhr
Bolt Size
Tinst
1 2
Place the plug and the object to fix.
Tighten the screw. Fixing completed.Drill a hole and clean it with a brush, remove dust with a blower.
3 4
ww
w.u
nim
etal
-ikk.
com
Cable maNaGemeNt SyStemSCable tray SyStemS
www.unimetal-ikk.com52
technical Data:Recommended loads (non-concreted C 20/25).
Setting Data:Edge distance > 1.5 x effective anchorage depth, distance between anchors > 3,0 x effective anchorage depth, min. thickness of foundation > 2,5 x H eff.
Installation Parmeters:H eff = Effective anchorage depth.
Drop-in anchor - SDa
Features:- Provides permanently fixed threaded socket in concrete.- Use in non-cracked concrete or cracked concrete and natural stone.- The anchor will spread and tighten against the drilled hole after inserting with setting tool.- Low setting depth, reduced drilling time.- Enables cost-effective assembly .- Multiple removing and fixing.
Typical Applications: Pipes, ventilation ducts, suspended ceilings, sprinkler systems, brackets, threaded rods and cable trays.
Threadedsize
Tension Load(KN)
Shear Load(KN)
Bending Moment(Nm)
M6 2.4 1.9 3.8
M8 3.2 2.3 9.4
M10 4.9 2.8 16.3
M12 7.3 5.3 32.7
M16 9.8 8.4 75
Size H eff.(mm)
Edge DistanceC (mm)
Distance BetweenAnchors S (mm)
Thickness ofFoundation hmin (mm)
Tightening Torque (Nm)
Spannersize
M6 25 37.5 75 100 4 10
M8 30 45 90 100 9 13
M10 40 60 120 130 17 17
M12 50 75 150 140 30 19
M16 65 197.5 195 160 75 24
Thread Size
AnchorLength (mm)
ThreadLength (mm)
Drill (Ø) (mm)
Drilling Depth (mm)
Effective Anchorage Depth H eff.
(mm)
Min. Screw Depth E
(mm)
Max.Screw Depth E
(mm)
M6 25 11 8 25 25 6 12
M8 30 13 10 30 30 8 13
M10 40 15 12 40 40 10 17
M12 50 20 16 50 50 12 18
M16 65 25 20 65 65 16 23
Anchor Length
Drilling Depth
E E= Screw Depth
Drill Ø
H eff
AHM Sleeve Anchor serutaeF
secnatsidecapsdnaegdellamSTorque controlled expansionZinc plated > 5µmThrough xing
Applications snoitcurtsnoc-rednu,selorp,senihcam,snoitcurtsnocleets
noitallatsnI
S-AHM Sleeve Anchor with hexagon screw htgneLmmØllirDmm
htpedgnillirDdaerhTmm
htgnelelbasUmm
htpedgnitteSmin.mm
6M6M8M8M01M01M
B-AHM Sleeve Anchor with threaded bolt and nut
58 Mungo Befestigungstechnik AG
Met
al P
rodu
cts
kat_en-2007-11-29.indd 58 4.12.2007 10:13:36 Uhr
Tension load (kN)
Type(Order No)
Shear load (kN)
Bending moment (Nm)
Distance betweenanchor S (mm)
6M8M01M21M
2.03.05.0
5.7
105120150225
Min. thickness of found
(hmin) mm
Tighten torque(Nm)
Spannersize (SAS)
Spannersize (SAB)
Drill Ø(mm)
Size(mm)
Length(mm)
Usablelength(mm)
Drilling depth(mm)
Settingdepth min.
(mm)88
10101212
M6M6M8M8
M10M10
4560608070
100
555560607070
51515251535
353540405050
Drill Ø(mm)
Size(mm)
Length(mm)
Usablelength(mm)
Drilling depth(mm)
Settingdepth min.
(mm)88
101010121212161616
M6M6M8M8M8
M10M10M10M12M12M12
406550759575
10013065
110145
5555606060707070909090
5255
30501540705
2560
3535404040505050757575
Plug & drill Ø(mm)
Length(mm)
UsableDrilling Depth(mm)
Length(mm)
SettingDepth Min.
(mm)5406060807001
555506060707
55151525153
535304040505
8801012121
2.53.35.58.0
90.0100.0120.0140.0
10.013.017.0---
10.013.015.019.0
8.025.040.050.0
4.205.30
12.8025.0
Distance to edge C (mm)
55.060.075.0
115.0
Tinst
materials:- zinc plated steel.- stainless steel [ SS 304 (A2) , SS 316 (A4) ].
*for cracked Concrete we shall use 0,5 x this value (approximately)
SDA
Cab
le t
ray
SyS
tem
S
53
Heavy Duty anchors
34 Technical Advisory Service Tel: +44 (0) 1530 812 857, Fax: +44 (0) 1530 812 862
R-DCA WEDGE ANCHORFOR CONCRETE & STONE
DESCRIPTIONProvides permanently �xed threaded sockets in concrete. Allows bolts or studs to be installed and removed without damaging the anchor. Available in: zinc plated steel and stainless steel grade A4 (1.4401). Install with manual setting tool or mechanical setting tool for use with hammer action drilling machines.
SUITABLE FOR USE IN:ConcreteStone.
FEATURES1. Internally threaded to take stud or bolt.2. Easy to install by hammer action.3. Slotted sleeve and captive internal tapered wedge to
facilitate easy setting and expansion.
Product Information
Installation
1. Drill a hole of required diameter and depth.
2. Remove debris and thoroughly clean hole with brush and pump.
3. Insert wedge anchor, slotted end �rst.
5. Alternatively use mechanical setting tool with appropriate drilling machine.
4. Use the setting tool to drive the internal wedge into the anchor.
R-DCA WEDGE ANCHOR - ZINC PLATED
THREADSIZE(d)
ANCHORLENGTH
(mm)( l )
THREAD LENGTH(mm)(lG )
HOLE DIAMETER
(mm)(do)
HOLE DEPTH(mm)(ho )
MAXIMUMRECOMMENDED
TORQUE(Nm)
(Tinst )
PRODUCT CODE NEW CODE
M6 25 118 27 4.5 77-108 WA-06M8 30 13 10 32 11 77-120 WA-08
M10 40 15 12 42 22 77-132 WA-10M12 50 20 15 52 38 77-141 WA-12M16 65 25 20 67 95 77-150 WA-16M20 80 35 25 82 185 77-162 WA-20
Manual Setting Tool Mechanical Setting Tool
R-DCA WEDGE ANCHOR - STAINLESS STEEL
THREADSIZE(d)
ANCHORLENGTH
(mm)( l )
THREAD LENGTH(mm)(lG )
HOLE DIAMETER
(mm)(do)
HOLE DEPTH(mm)(ho )
MAXIMUMRECOMMENDED
TORQUE(Nm)
(Tinst )
PRODUCT CODE NEW CODE
M6 25 118 27 4.5 77-608 WA-A4-06M8 30 13 10 32 11 77-620 WA-A4-08
M10 40 15 12 42 22 77-632 WA-A4-10M12 50 20 15 52 38 77-641 WA-A4-12M16 65 25 20 67 95 77-650 WA-A4-16
ETA PENDING 2007
TYPICAL APPLICATIONSe For permanently �xing threaded sockets in concrete and good quality stone.e Ideal for secure �xing for mechanical services, cable trays, platforms, drain covers, suspended ceilings etc.e Securing equipment that may need to be removed or replaced.
Stainless Steelfor bolt
34 Technical Advisory Service Tel: +44 (0) 1530 812 857, Fax: +44 (0) 1530 812 862
R-DCA WEDGE ANCHORFOR CONCRETE & STONE
DESCRIPTIONProvides permanently �xed threaded sockets in concrete. Allows bolts or studs to be installed and removed without damaging the anchor. Available in: zinc plated steel and stainless steel grade A4 (1.4401). Install with manual setting tool or mechanical setting tool for use with hammer action drilling machines.
SUITABLE FOR USE IN:ConcreteStone.
FEATURES1. Internally threaded to take stud or bolt.2. Easy to install by hammer action.3. Slotted sleeve and captive internal tapered wedge to
facilitate easy setting and expansion.
Product Information
Installation
1. Drill a hole of required diameter and depth.
2. Remove debris and thoroughly clean hole with brush and pump.
3. Insert wedge anchor, slotted end �rst.
5. Alternatively use mechanical setting tool with appropriate drilling machine.
4. Use the setting tool to drive the internal wedge into the anchor.
R-DCA WEDGE ANCHOR - ZINC PLATED
THREADSIZE(d)
ANCHORLENGTH
(mm)( l )
THREAD LENGTH(mm)(lG )
HOLE DIAMETER
(mm)(do)
HOLE DEPTH(mm)(ho )
MAXIMUMRECOMMENDED
TORQUE(Nm)
(Tinst )
PRODUCT CODE NEW CODE
M6 25 118 27 4.5 77-108 WA-06M8 30 13 10 32 11 77-120 WA-08
M10 40 15 12 42 22 77-132 WA-10M12 50 20 15 52 38 77-141 WA-12M16 65 25 20 67 95 77-150 WA-16M20 80 35 25 82 185 77-162 WA-20
Manual Setting Tool Mechanical Setting Tool
R-DCA WEDGE ANCHOR - STAINLESS STEEL
THREADSIZE(d)
ANCHORLENGTH
(mm)( l )
THREAD LENGTH(mm)(lG )
HOLE DIAMETER
(mm)(do)
HOLE DEPTH(mm)(ho )
MAXIMUMRECOMMENDED
TORQUE(Nm)
(Tinst )
PRODUCT CODE NEW CODE
M6 25 118 27 4.5 77-608 WA-A4-06M8 30 13 10 32 11 77-620 WA-A4-08
M10 40 15 12 42 22 77-632 WA-A4-10M12 50 20 15 52 38 77-641 WA-A4-12M16 65 25 20 67 95 77-650 WA-A4-16
ETA PENDING 2007
TYPICAL APPLICATIONSe For permanently �xing threaded sockets in concrete and good quality stone.e Ideal for secure �xing for mechanical services, cable trays, platforms, drain covers, suspended ceilings etc.e Securing equipment that may need to be removed or replaced.
Stainless Steelfor bolt
34 Technical Advisory Service Tel: +44 (0) 1530 812 857, Fax: +44 (0) 1530 812 862
R-DCA WEDGE ANCHORFOR CONCRETE & STONE
DESCRIPTIONProvides permanently xed threaded sockets in concrete.Allows bolts or studs to be installed and removed withoutdamaging the anchor.Available in: zinc plated steel and stainless steel grade A4(1.4401).Install with manual setting tool or mechanical setting tool for use with hammer action drilling machines.
SUITABLE FOR USE IN:ConcreteStone.
FEATURES1. Internally threaded to take stud or bolt.2. Easy to install by hammer action.3. Slotted sleeve and captive internal tapered wedge to
facilitate easy setting and expansion.
Product Information
Installation
1. Drill a hole of required diameter and depth.
2. Remove debris andthoroughly clean hole withbrush and pump.
3. Insert wedge anchor,slotted end
5. Alternatively use mechanicalsetting tool with appropriatedrilling machine.
4. Use the setting tool to drive the internal wedge into the anchor.
R-DCA WEDGE ANCHOR - ZINC PLATED
THREADSIZE(d)
ANCHORLENGTH
(mm)( l )
THREAD LENGTH(mm)(lG )
HOLEDIAMETER
(mm)(do)
HOLE DEPTH(mm)(ho )
MAXIMUMRECOMMENDED
TORQUE(Nm)
(Tinst )
PRODUCT CODE NEW CODE
M6 25 11 8 27 4.5 77-108 WA-06M8 30 13 10 32 11 77-120 WA-08
M10 40 15 12 42 22 77-132 WA-10M12 50 20 15 52 38 77-141 WA-12M16 65 25 20 67 95 77-150 WA-16M20 80 35 25 82 185 77-162 WA-20
Manual Setting Tool
THREAD SIZE(d)
M6M8
M10M12M16M20
Mechanical Setting Tool
THREAD SIZE(d)
GRIP TYPE
M6 SDS-plusM8 SDS-plus
M10 SDS-plusM12 SDS-plusM16 SDS-maxM20 SDS-max
R-DCA WEDGE ANCHOR - STAINLESS STEEL
THREADSIZE(d)
ANCHORLENGTH
(mm)( l )
THREAD LENGTH(mm)(lG )
HOLEDIAMETER
(mm)(do)
HOLE DEPTH(mm)(ho )
MAXIMUMRECOMMENDED
TORQUE(Nm)
(Tinst )
PRODUCT CODE NEW CODE
M6 25 11 8 27 4.5 77-608 WA-A4-06M8 30 13 10 32 11 77-620 WA-A4-08
M10 40 15 12 42 22 77-632 WA-A4-10M12 50 20 15 52 38 77-641 WA-A4-12M16 65 25 20 67 95 77-650 WA-A4-16
ETA PENDING 2007
TYPICAL APPLICATIONSe For permanently xing threaded sockets in concrete and good quality stone.e Ideal for secure for mechanical services, cable trays, platforms, drain covers, suspended ceilings etc.e Securing equipment that may need to be removed or replaced.
RAWL_KATALOG_2007_2008.indb 34 2007-10-15 14:34:42
34 Technical Advisory Service Tel: +44 (0) 1530 812 857, Fax: +44 (0) 1530 812 862
R-DCA WEDGE ANCHORFOR CONCRETE & STONE
DESCRIPTIONProvides permanently xed threaded sockets in concrete.Allows bolts or studs to be installed and removed withoutdamaging the anchor.Available in: zinc plated steel and stainless steel grade A4(1.4401).Install with manual setting tool or mechanical setting tool for use with hammer action drilling machines.
SUITABLE FOR USE IN:ConcreteStone.
FEATURES1. Internally threaded to take stud or bolt.2. Easy to install by hammer action.3. Slotted sleeve and captive internal tapered wedge to
facilitate easy setting and expansion.
Product Information
Installation
1. Drill a hole of required diameter and depth.
2. Remove debris andthoroughly clean hole withbrush and pump.
3. Insert wedge anchor,slotted end
5. Alternatively use mechanicalsetting tool with appropriatedrilling machine.
4. Use the setting tool to drive the internal wedge into the anchor.
R-DCA WEDGE ANCHOR - ZINC PLATED
THREADSIZE(d)
ANCHORLENGTH
(mm)( l )
THREAD LENGTH(mm)(lG )
HOLEDIAMETER
(mm)(do)
HOLE DEPTH(mm)(ho )
MAXIMUMRECOMMENDED
TORQUE(Nm)
(Tinst )
PRODUCT CODE NEW CODE
M6 25 11 8 27 4.5 77-108 WA-06M8 30 13 10 32 11 77-120 WA-08
M10 40 15 12 42 22 77-132 WA-10M12 50 20 15 52 38 77-141 WA-12M16 65 25 20 67 95 77-150 WA-16M20 80 35 25 82 185 77-162 WA-20
Manual Setting Tool
THREAD SIZE(d)
M6M8
M10M12M16M20
Mechanical Setting Tool
THREAD SIZE(d)
GRIP TYPE
M6 SDS-plusM8 SDS-plus
M10 SDS-plusM12 SDS-plusM16 SDS-maxM20 SDS-max
R-DCA WEDGE ANCHOR - STAINLESS STEEL
THREADSIZE(d)
ANCHORLENGTH
(mm)( l )
THREAD LENGTH(mm)(lG )
HOLEDIAMETER
(mm)(do)
HOLE DEPTH(mm)(ho )
MAXIMUMRECOMMENDED
TORQUE(Nm)
(Tinst )
PRODUCT CODE NEW CODE
M6 25 11 8 27 4.5 77-608 WA-A4-06M8 30 13 10 32 11 77-620 WA-A4-08
M10 40 15 12 42 22 77-632 WA-A4-10M12 50 20 15 52 38 77-641 WA-A4-12M16 65 25 20 67 95 77-650 WA-A4-16
ETA PENDING 2007
TYPICAL APPLICATIONSe For permanently xing threaded sockets in concrete and good quality stone.e Ideal for secure for mechanical services, cable trays, platforms, drain covers, suspended ceilings etc.e Securing equipment that may need to be removed or replaced.
RAWL_KATALOG_2007_2008.indb 34 2007-10-15 14:34:42
Use the setting tool to drive the internal wedge into the anchor.
Alternatively use the mechanical setting tool with an appropriate drilling machine.
Manual Setting Tool
Manual Setting Tool
Mechanical Setting Tool
Installation
Throughbolt, stainless steel A4/316
serutaeFetercnocdekcarcnurof7noitpOlavorppAlacinhceTnaeporuE
Torque controlled expansionApplications in damp areas and outdoorsStainless steel A4/316Face xing or through xing
Applications ,senihcam,snoitcurtsnocleets,sgniliar,syartelbac,sedacaf
under-constructions, high-racks, pro les
Tension load (kN)
Shear load (kN)
Bending moment (Nm)
Edge Distance C (mm)
He�. (mm)
Distance betweenanchor S (mm)
Thickness offoundation
(mm)
Tighten torque(Nm)
Spanner size
6M 2.64.15.89.214
3.36.38.51223
5153050
100
5.513
26.546.5
118.5
4050586880
Washer (Ø)
12 x 1.616 x 1.620 x 2.024 x 2.530 x 3.0
02106 001 018M 05157 001 3101M 47178 021 7121M 402201 041 9161M 042021 061 42
noitallatsnI
2
03505604015660452086040459672505803010680501088055158805525980554511833506015301070185515901850301101855452101850604101850806101850010810194508218651011218603521218605541218607561218609581210701511610851031610803541610854061610856081610010306102
50 Mungo Befestigungstechnik AG
Plug & drill Ø(mm)
Length(mm)
UsableLength(mm)
Settingdepth min.
(mm)
kat_en-2007-11-29.indd 50 4.12.2007 10:12:24 Uhr
Bolt Size
Tinst
1 2
Insert the anchor sleeve in the hole.
3
Tighten to the recommended torque.
4
Fixing completed.Drill a hole and clean it with a brush, remove dust with a blower.
Manual Mechanical
ww
w.u
nim
etal
-ikk.
com
Cable maNaGemeNt SyStemSCable tray SyStemS
www.unimetal-ikk.com54
Sleeve anchor - SaS
materials:- zinc plated steel.- stainless steel [ SS 304 (A2) , SS 316 (A4) ].
Features:- Suitable for use in concrete, natural stone, brickwork and blockwork- small distance between achors.- Optimum performance in most base material types.- No protruding threads after installation.- Small distance between anchors and from edge.- Controlled expansion.- Zinc plated > 5µm.- Effective force distribution in the drilled hole.- Sleeve anchor with hexagon screw or with threaded bolt.
Typical Applications:Uni-channel ,railings, steel constructions , machines, high-racks, cable support systems and mechanical fixations.
technical Data:Recommended loads (non-concreted C 20/25).
AHM Sleeve Anchor serutaeF
secnatsidecapsdnaegdellamSTorque controlled expansionZinc plated > 5µmThrough xing
Applications snoitcurtsnoc-rednu,selorp,senihcam,snoitcurtsnocleets
noitallatsnI
S-AHM Sleeve Anchor with hexagon screw htgneLmmØllirDmm
htpedgnillirDdaerhTmm
htgnelelbasUmm
htpedgnitteSmin.mm
6M6M8M8M01M01M
B-AHM Sleeve Anchor with threaded bolt and nut
58 Mungo Befestigungstechnik AG
Met
al P
rodu
cts
kat_en-2007-11-29.indd 58 4.12.2007 10:13:36 Uhr
Tension load (kN)
Type(Order No)
Shear load (kN)
Bending moment (Nm)
Distance betweenanchor S (mm)
6M8M01M21M
2.03.05.0
5.7
105120150225
Min. thickness of found
(hmin) mm
Tighten torque(Nm)
Spannersize (SAS)
Spannersize (SAB)
Drill Ø(mm)
Size(mm)
Length(mm)
Usablelength(mm)
Drilling depth(mm)
Settingdepth min.
(mm)88
10101212
M6M6M8M8
M10M10
4560608070
100
555560607070
51515251535
353540405050
Drill Ø(mm)
Size(mm)
Length(mm)
Usablelength(mm)
Drilling depth(mm)
Settingdepth min.
(mm)88
101010121212161616
M6M6M8M8M8
M10M10M10M12M12M12
406550759575
10013065
110145
5555606060707070909090
5255
30501540705
2560
3535404040505050757575
Plug & drill Ø(mm)
Length(mm)
UsableDrilling Depth(mm)
Length(mm)
SettingDepth Min.
(mm)5406060807001
555506060707
55151525153
535304040505
8801012121
2.53.35.58.0
90.0100.0120.0140.0
10.013.017.0---
10.013.015.019.0
8.025.040.050.0
4.205.30
12.8025.0
Distance to edge C (mm)
55.060.075.0
115.0
Tinst
Bolt Size Tension Load(KN)
Shear Load(KN)
Bending Moment(Nm)
M6 2.56 2.0 5.0
M8 3.33 3.3 12.5
M10 4.1 5.0 25.5
M12 6.66 7.5 .......
Bolt Size H eff.(mm)
Edge DistanceC (mm)
Distance BetweenAnchors S (mm)
Thickness ofFoundationhmin (mm)
Washer (Ø)(mm)
Tightening Torque (Nm)
Spannersize
M6 35 52.5 105 70 18 x 1.6 8 10
M8 40 60 120 80 16 x 1.6 25 13
M10 50 75 150 100 20 x 2.0 40 17
M12 75 112.5 225 150 26 x 2.0 50 19
Sleeve anchor - SaS:with hexagon screw (non-cracked concrete C20/25).
Setting Depth
H eff
Length
Washer
MSpaner
Size
Drilling DepthUsable Length
Drill Ø
Size Length (mm)
Drill (Ø) (mm)
Hole Ø in Fixture (mm)
Drilling Depth (mm)
Setting Depth
(Ø)
H eff.(mm)
Min.Usable Length(mm)
M6 45 8 10 55 35 35 5
M6 60 8 10 55 35 35 15
M8 60 10 12 60 40 40 15
M8 80 10 12 60 40 40 25
M10 70 12 14 70 50 50 15
M10 100 12 14 70 60 50 35
Setting Data:Edge distance > 1.5 x effective anchorage depth, distance between anchors> 3,0 x effective anchorage depth, min. thickness of foundation > 2,5 x H eff.
*for cracked Concrete we shall use 0,5 x this value (approximately)
*for cracked Concrete we shall use 0,5 x this value (approximately).
SAS
Cab
le t
ray
SyS
tem
S
55
Heavy Duty anchors
Sleeve anchor - Sab:with threaded bolt and nut
Setting Depth
H eff
Length
Washer
MSpanner
Size
Drilling Depth
Usable Length
Drill Ø
Size Length (mm)
Drill (Ø) (mm)
Hole Ø in Fixture (mm)
Min.Drilling Depth (mm)
Min. Setting Depth
(Ø)
H eff.(mm)
Max. Usable Length(mm)
M6 49 8 10 29 27 25 20
M6 64 8 10 29 27 25 35
M8 60 10 12 34 32 30 25
M8 75 10 12 34 32 30 40
M8 105 10 12 34 32 30 70
M8 85 10 12 34 32 30 50
M10 73 12 14 44 42 40 25
M10 88 12 14 44 42 40 40
M10 108 12 14 44 42 40 60
M10 138 12 14 44 42 40 90
M12 100 16 18 64 62 60 30
M12 120 16 18 64 62 60 50
M16 165 20 22 84 82 80 70
Throughbolt, stainless steel A4/316
serutaeFetercnocdekcarcnurof7noitpOlavorppAlacinhceTnaeporuE
Torque controlled expansionApplications in damp areas and outdoorsStainless steel A4/316Face xing or through xing
Applications ,senihcam,snoitcurtsnocleets,sgniliar,syartelbac,sedacaf
under-constructions, high-racks, pro les
Tension load (kN)
Shear load (kN)
Bending moment (Nm)
Edge Distance C (mm)
He�. (mm)
Distance betweenanchor S (mm)
Thickness offoundation
(mm)
Tighten torque(Nm)
Spanner size
6M 2.64.15.89.214
3.36.38.51223
5153050
100
5.513
26.546.5
118.5
4050586880
Washer (Ø)
12 x 1.616 x 1.620 x 2.024 x 2.530 x 3.0
02106 001 018M 05157 001 3101M 47178 021 7121M 402201 041 9161M 042021 061 42
noitallatsnI
2
03505604015660452086040459672505803010680501088055158805525980554511833506015301070185515901850301101855452101850604101850806101850010810194508218651011218603521218605541218607561218609581210701511610851031610803541610854061610856081610010306102
50 Mungo Befestigungstechnik AG
Plug & drill Ø(mm)
Length(mm)
UsableLength(mm)
Settingdepth min.
(mm)
kat_en-2007-11-29.indd 50 4.12.2007 10:12:24 Uhr
Bolt Size
Tinst
1
Drill a hole and clean it with a brush, remove dust with a blower.
Insert the sleeve anchor through the fixture into the hole.
Tighten to the recommended torque.
AHM Sleeve Anchor serutaeF
secnatsidecapsdnaegdellamSTorque controlled expansionZinc plated > 5µmThrough xing
Applications snoitcurtsnoc-rednu,selorp,senihcam,snoitcurtsnocleets
noitallatsnI
S-AHM Sleeve Anchor with hexagon screw htgneLmmØllirDmm
htpedgnillirDdaerhTmm
htgnelelbasUmm
htpedgnitteSmin.mm
6M6M8M8M01M01M
B-AHM Sleeve Anchor with threaded bolt and nut
58 Mungo Befestigungstechnik AG
Met
al P
rodu
cts
kat_en-2007-11-29.indd 58 4.12.2007 10:13:36 Uhr
Tension load (kN)
Type(Order No)
Shear load (kN)
Bending moment (Nm)
Distance betweenanchor S (mm)
6M8M01M21M
2.03.05.0
5.7
105120150225
Min. thickness of found
(hmin) mm
Tighten torque(Nm)
Spannersize (SAS)
Spannersize (SAB)
Drill Ø(mm)
Size(mm)
Length(mm)
Usablelength(mm)
Drilling depth(mm)
Settingdepth min.
(mm)88
10101212
M6M6M8M8
M10M10
4560608070
100
555560607070
51515251535
353540405050
Drill Ø(mm)
Size(mm)
Length(mm)
Usablelength(mm)
Drilling depth(mm)
Settingdepth min.
(mm)88
101010121212161616
M6M6M8M8M8
M10M10M10M12M12M12
406550759575
10013065
110145
5555606060707070909090
5255
30501540705
2560
3535404040505050757575
Plug & drill Ø(mm)
Length(mm)
UsableDrilling Depth(mm)
Length(mm)
SettingDepth Min.
(mm)5406060807001
555506060707
55151525153
535304040505
8801012121
2.53.35.58.0
90.0100.0120.0140.0
10.013.017.0---
10.013.015.019.0
8.025.040.050.0
4.205.30
12.8025.0
Distance to edge C (mm)
55.060.075.0
115.0
Tinst
2
Installation of Sleeve Anchor - SAS
AHM Sleeve Anchor serutaeF
secnatsidecapsdnaegdellamSTorque controlled expansionZinc plated > 5µmThrough xing
Applications snoitcurtsnoc-rednu,selorp,senihcam,snoitcurtsnocleets
noitallatsnI
S-AHM Sleeve Anchor with hexagon screw htgneLmmØllirDmm
htpedgnillirDdaerhTmm
htgnelelbasUmm
htpedgnitteSmin.mm
6M6M8M8M01M01M
B-AHM Sleeve Anchor with threaded bolt and nut
58 Mungo Befestigungstechnik AG
Met
al P
rodu
cts
kat_en-2007-11-29.indd 58 4.12.2007 10:13:36 Uhr
Tension load (kN)
Type(Order No)
Shear load (kN)
Bending moment (Nm)
Distance betweenanchor S (mm)
6M8M01M21M
2.03.05.0
5.7
105120150225
Min. thickness of found
(hmin) mm
Tighten torque(Nm)
Spannersize (SAS)
Spannersize (SAB)
Drill Ø(mm)
Size(mm)
Length(mm)
Usablelength(mm)
Drilling depth(mm)
Settingdepth min.
(mm)88
10101212
M6M6M8M8
M10M10
4560608070
100
555560607070
51515251535
353540405050
Drill Ø(mm)
Size(mm)
Length(mm)
Usablelength(mm)
Drilling depth(mm)
Settingdepth min.
(mm)88
101010121212161616
M6M6M8M8M8
M10M10M10M12M12M12
406550759575
10013065
110145
5555606060707070909090
5255
30501540705
2560
3535404040505050757575
Plug & drill Ø(mm)
Length(mm)
UsableDrilling Depth(mm)
Length(mm)
SettingDepth Min.
(mm)5406060807001
555506060707
55151525153
535304040505
8801012121
2.53.35.58.0
90.0100.0120.0140.0
10.013.017.0---
10.013.015.019.0
8.025.040.050.0
4.205.30
12.8025.0
Distance to edge C (mm)
55.060.075.0
115.0
Tinst
3
1
1
Place the fixture (object) and drill a hole.
Drill a hole of requested diameter and depth.
Remove dust with a blower and clean the hole with a brush.
Remove dust with a blower and clean the hole with a brush.
Tap the anchor through the fixture with a hammer or a setting tool.
Tap with a hammer or a setting tool until fixing depth is reached.
Tighten to the recommended torque.
Tighten to the recommended torque.
2
2
Installation ( push-through installation )
Installation ( pre-positioned installation )
3
3
4
4
ww
w.u
nim
etal
-ikk.
com
Cable maNaGemeNt SyStemSCable tray SyStemS
www.unimetal-ikk.com56
materials:- zinc plated steel. - stainless steel [ SS 304 (A2) , SS 316 (A4) ].
Features: - Suitable for use in cracked concrete or in non-cracked concrete and in natural stone.- Special design of the clip in stainless steel which ensures a safe hold in the hole.- Torque controlled expansion.- Zinc plated > 5µm.- User friendly, face fixing or through fixing.
Typical Applications:Uni - channel, hand rails, steel constructions, cable trays, supports, brackets, ducts and shelf feet.
Throughbolt, stainless steel A4/316
serutaeFetercnocdekcarcnurof7noitpOlavorppAlacinhceTnaeporuE
Torque controlled expansionApplications in damp areas and outdoorsStainless steel A4/316Face xing or through xing
Applications ,senihcam,snoitcurtsnocleets,sgniliar,syartelbac,sedacaf
under-constructions, high-racks, pro les
Tension load (kN)
Shear load (kN)
Bending moment (Nm)
Edge Distance C (mm)
He�. (mm)
Distance betweenanchor S (mm)
Thickness offoundation
(mm)
Tighten torque(Nm)
Spanner size
6M 2.64.15.89.214
3.36.38.51223
5153050
100
5.513
26.546.5
118.5
4050586880
Washer (Ø)
12 x 1.616 x 1.620 x 2.024 x 2.530 x 3.0
02106 001 018M 05157 001 3101M 47178 021 7121M 402201 041 9161M 042021 061 42
noitallatsnI
2
03505604015660452086040459672505803010680501088055158805525980554511833506015301070185515901850301101855452101850604101850806101850010810194508218651011218603521218605541218607561218609581210701511610851031610803541610854061610856081610010306102
50 Mungo Befestigungstechnik AG
Plug & drill Ø(mm)
Length(mm)
UsableLength(mm)
Settingdepth min.
(mm)
kat_en-2007-11-29.indd 50 4.12.2007 10:12:24 Uhr
Bolt Size
Tinst
technical Data:Through bolt zinc plated (non-cracked C20/25).
Setting Data:Edge distance > 1,5 H eff. , distance between anchors > 3 x H eff.
Thickness of foundation > 2 x H eff.
Throughbolt, stainless steel A4/316
serutaeFetercnocdekcarcnurof7noitpOlavorppAlacinhceTnaeporuE
Torque controlled expansionApplications in damp areas and outdoorsStainless steel A4/316Face xing or through xing
Applications ,senihcam,snoitcurtsnocleets,sgniliar,syartelbac,sedacaf
under-constructions, high-racks, pro les
Tension load (kN)
Shear load (kN)
Bending moment (Nm)
Edge Distance C (mm)
He�. (mm)
Distance betweenanchor S (mm)
Thickness offoundation
(mm)
Tighten torque(Nm)
Spanner size
6M 2.64.15.89.214
3.36.38.51223
5153050
100
5.513
26.546.5
118.5
4050586880
Washer (Ø)
12 x 1.616 x 1.620 x 2.024 x 2.530 x 3.0
02106 001 018M 05157 001 3101M 47178 021 7121M 402201 041 9161M 042021 061 42
noitallatsnI
2
03505604015660452086040459672505803010680501088055158805525980554511833506015301070185515901850301101855452101850604101850806101850010810194508218651011218603521218605541218607561218609581210701511610851031610803541610854061610856081610010306102
50 Mungo Befestigungstechnik AG
Plug & drill Ø(mm)
Length(mm)
UsableLength(mm)
Settingdepth min.
(mm)
kat_en-2007-11-29.indd 50 4.12.2007 10:12:24 Uhr
Bolt Size
Tinst
Through bolt
BoltSize
Tension Load(KN)
Shear Load(KN)
Bending Moment(Nm)
M6 2.1 3.0 5.5
M8 4.0 4.8 13.0
M10 5.5 8.5 26.5
M12 7.5 9.5 46.5
M16 13.0 16.0 118.5
Bolt Size H eff.(mm)
Edge DistanceC (mm)
Distance Between
Anchors S (mm)
Washer(Ø)
Thickness ofFoundationhmin (mm)
Tightening Torque (Nm)
SpannerSize
M6 40 60 120 12 x 1.6 100 7 10
M8 50 75 150 16 x 1.6 100 14 13
M10 58 87 174 20 x 2.0 120 30 17
M12 68 102 204 24 x 2.5 140 35 19
M16 80 120 240 30 x 3.0 160 80 24
Through Bolt (Wedge Anchor) - STB
Setting Depth
H eff
Bolt Length
Washer
Drilling DepthUsable Length
Drill ØAHM Sleeve Anchor
serutaeFsecnatsidecapsdnaegdellamS
Torque controlled expansionZinc plated > 5µmThrough xing
Applications snoitcurtsnoc-rednu,selorp,senihcam,snoitcurtsnocleets
noitallatsnI
S-AHM Sleeve Anchor with hexagon screw htgneLmmØllirDmm
htpedgnillirDdaerhTmm
htgnelelbasUmm
htpedgnitteSmin.mm
6M6M8M8M01M01M
B-AHM Sleeve Anchor with threaded bolt and nut
58 Mungo Befestigungstechnik AG
Met
al P
rodu
cts
kat_en-2007-11-29.indd 58 4.12.2007 10:13:36 Uhr
Tension load (kN)
Type(Order No)
Shear load (kN)
Bending moment (Nm)
Distance betweenanchor S (mm)
6M8M01M21M
2.03.05.0
5.7
105120150225
Min. thickness of found
(hmin) mm
Tighten torque(Nm)
Spannersize (SAS)
Spannersize (SAB)
Drill Ø(mm)
Size(mm)
Length(mm)
Usablelength(mm)
Drilling depth(mm)
Settingdepth min.
(mm)88
10101212
M6M6M8M8
M10M10
4560608070
100
555560607070
51515251535
353540405050
Drill Ø(mm)
Size(mm)
Length(mm)
Usablelength(mm)
Drilling depth(mm)
Settingdepth min.
(mm)88
101010121212161616
M6M6M8M8M8
M10M10M10M12M12M12
406550759575
10013065
110145
5555606060707070909090
5255
30501540705
2560
3535404040505050757575
Plug & drill Ø(mm)
Length(mm)
UsableDrilling Depth(mm)
Length(mm)
SettingDepth Min.
(mm)5406060807001
555506060707
55151525153
535304040505
8801012121
2.53.35.58.0
90.0100.0120.0140.0
10.013.017.0---
10.013.015.019.0
8.025.040.050.0
4.205.30
12.8025.0
Distance to edge C (mm)
55.060.075.0
115.0
Tinst
*for cracked Concrete we shall use 0,5 x this value (approximately)
STB
Cab
le t
ray
SyS
tem
S
57
Heavy Duty anchors
Drill a hole and clean with a brush, remove dust with a blower.
Throughbolt, stainless steel A4/316
serutaeFetercnocdekcarcnurof7noitpOlavorppAlacinhceTnaeporuE
Torque controlled expansionApplications in damp areas and outdoorsStainless steel A4/316Face xing or through xing
Applications ,senihcam,snoitcurtsnocleets,sgniliar,syartelbac,sedacaf
under-constructions, high-racks, pro les
Tension load (kN)
Shear load (kN)
Bending moment (Nm)
Edge Distance C (mm)
He�. (mm)
Distance betweenanchor S (mm)
Thickness offoundation
(mm)
Tighten torque(Nm)
Spanner size
6M 2.64.15.89.214
3.36.38.51223
5153050
100
5.513
26.546.5
118.5
4050586880
Washer (Ø)
12 x 1.616 x 1.620 x 2.024 x 2.530 x 3.0
02106 001 018M 05157 001 3101M 47178 021 7121M 402201 041 9161M 042021 061 42
noitallatsnI
2
03505604015660452086040459672505803010680501088055158805525980554511833506015301070185515901850301101855452101850604101850806101850010810194508218651011218603521218605541218607561218609581210701511610851031610803541610854061610856081610010306102
50 Mungo Befestigungstechnik AG
Plug & drill Ø(mm)
Length(mm)
UsableLength(mm)
Settingdepth min.
(mm)
kat_en-2007-11-29.indd 50 4.12.2007 10:12:24 Uhr
Bolt Size
Tinst
Throughbolt, stainless steel A4/316
serutaeFetercnocdekcarcnurof7noitpOlavorppAlacinhceTnaeporuE
Torque controlled expansionApplications in damp areas and outdoorsStainless steel A4/316Face xing or through xing
Applications ,senihcam,snoitcurtsnocleets,sgniliar,syartelbac,sedacaf
under-constructions, high-racks, pro les
Tension load (kN)
Shear load (kN)
Bending moment (Nm)
Edge Distance C (mm)
He�. (mm)
Distance betweenanchor S (mm)
Thickness offoundation
(mm)
Tighten torque(Nm)
Spanner size
6M 2.64.15.89.214
3.36.38.51223
5153050
100
5.513
26.546.5
118.5
4050586880
Washer (Ø)
12 x 1.616 x 1.620 x 2.024 x 2.530 x 3.0
02106 001 018M 05157 001 3101M 47178 021 7121M 402201 041 9161M 042021 061 42
noitallatsnI
2
03505604015660452086040459672505803010680501088055158805525980554511833506015301070185515901850301101855452101850604101850806101850010810194508218651011218603521218605541218607561218609581210701511610851031610803541610854061610856081610010306102
50 Mungo Befestigungstechnik AG
Plug & drill Ø(mm)
Length(mm)
UsableLength(mm)
Settingdepth min.
(mm)
kat_en-2007-11-29.indd 50 4.12.2007 10:12:24 Uhr
Bolt Size
Tinst
Throughbolt, stainless steel A4/316
serutaeFetercnocdekcarcnurof7noitpOlavorppAlacinhceTnaeporuE
Torque controlled expansionApplications in damp areas and outdoorsStainless steel A4/316Face xing or through xing
Applications ,senihcam,snoitcurtsnocleets,sgniliar,syartelbac,sedacaf
under-constructions, high-racks, pro les
Tension load (kN)
Shear load (kN)
Bending moment (Nm)
Edge Distance C (mm)
He�. (mm)
Distance betweenanchor S (mm)
Thickness offoundation
(mm)
Tighten torque(Nm)
Spanner size
6M 2.64.15.89.214
3.36.38.51223
5153050
100
5.513
26.546.5
118.5
4050586880
Washer (Ø)
12 x 1.616 x 1.620 x 2.024 x 2.530 x 3.0
02106 001 018M 05157 001 3101M 47178 021 7121M 402201 041 9161M 042021 061 42
noitallatsnI
2
03505604015660452086040459672505803010680501088055158805525980554511833506015301070185515901850301101855452101850604101850806101850010810194508218651011218603521218605541218607561218609581210701511610851031610803541610854061610856081610010306102
50 Mungo Befestigungstechnik AG
Plug & drill Ø(mm)
Length(mm)
UsableLength(mm)
Settingdepth min.
(mm)
kat_en-2007-11-29.indd 50 4.12.2007 10:12:24 Uhr
Bolt Size
Tinst
1 2 3
Place the fixture and insert the through bolt with a hammer.
Tighten to the recommended torque.
Installation Parameters:Through bolt zinc plated, stainless steel or hot-dip galvanized.
H eff.= Effective anchorage depth
Bolt Size Bolt Length (mm)
Drill Ø(mm)
Hole Ø in Fixture (mm)
Drilling Depth (mm)
Setting Depth (mm)
H eff. (mm)
Usable Length Fix (mm)
M6
40 6 6.5 35 27 ..... 3
55 6 6.5 35 35 35 15
70 6 6.5 35 35 35 30
95 6 6.5 35 35 35 55
M8
50 8 9 35 35 ..... 10
65 8 9 40 40 ..... 20
80 8 9 40 40 40 35
95 8 9 40 40 40 50
105 8 9 40 40 40 60
M10
65 10 11 40 40 40 15
80 10 11 50 50 50 20
95 10 11 50 50 50 35
115 10 11 50 50 50 55
120 10 11 50 50 50 60
M12
80 12 13 65 50 50 20
100 12 13 65 60 60 30
120 12 13 65 60 60 50
135 12 13 65 60 60 65
M16
105 16 18 85 70 70 15
140 16 18 85 80 80 40
180 16 18 85 80 80 80
220 16 18 85 80 80 120
Installation
ww
w.u
nim
etal
-ikk.
com
Cable maNaGemeNt SyStemSCable tray SyStemS
www.unimetal-ikk.com58
Features:- Assembly detachable, multiple removing and fixing.- Low energy impact, power-saving assembly.- Force controlled expansion.- Flexibility inside threaded anchor.- Variable length and art of threaded rods or bolts.- By tightening the screw, the cone pulls into the sleeve and tense against the drill hole.- Small edge distance and small distance between anchor.- Expansion elements are held together by a spring.- Optimum taper nut angle for maximum expansion.- Pressed steel segment ensures consistent dimensional accuracy.- Provide a projecting stud to support fixture during installation and removal.- Suitable for use in concrete, natural stone, Brick and sand stone.
technical Data:Recommended loads (concrete C 20/25 and in brick work).
Setting Data:Edge distance > 1,5 x H eff., distance between anchors > 3 x H eff. Thickness of foundation > 2 x H eff.
SizeConcrete Brick Work
Tension ShearKN
Torque Concrete
N.m
Torque Brick
N.mTension
KNShear
KN
M6 3.3 2.1 1.6 6.5 5.0
M8 4.8 4.4 2.1 15.0 7.5
M10 6.2 6.1 2.6 27.0 13.0
M12 9.7 12.4 3.9 50.0 23.0
SizeDistance to Edge
C (mm)Distance Between Anchors S (mm)
Min. Thickness ofFoundation hmin(mm)
H eff.(mm)
M6 52.5 105 70 35
M8 60 120 80 40
M10 75 150 100 50
M12 90 180 120 60
H eff.Setting Depth
Usable Lengtht Fixture
DrillØ
Drilling Depth(Hole Depth)
Bolt Length
Cone
Shield anchor - SSa
Typical Applications:For fixing : steel constructions, handrails, consoles, brackets, ladders, gates and spacing designs.
AHM Sleeve Anchor serutaeF
secnatsidecapsdnaegdellamSTorque controlled expansionZinc plated > 5µmThrough xing
Applications snoitcurtsnoc-rednu,selorp,senihcam,snoitcurtsnocleets
noitallatsnI
S-AHM Sleeve Anchor with hexagon screw htgneLmmØllirDmm
htpedgnillirDdaerhTmm
htgnelelbasUmm
htpedgnitteSmin.mm
6M6M8M8M01M01M
B-AHM Sleeve Anchor with threaded bolt and nut
58 Mungo Befestigungstechnik AG
Met
al P
rodu
cts
kat_en-2007-11-29.indd 58 4.12.2007 10:13:36 Uhr
Tension load (kN)
Type(Order No)
Shear load (kN)
Bending moment (Nm)
Distance betweenanchor S (mm)
6M8M01M21M
2.03.05.0
5.7
105120150225
Min. thickness of found
(hmin) mm
Tighten torque(Nm)
Spannersize (SAS)
Spannersize (SAB)
Drill Ø(mm)
Size(mm)
Length(mm)
Usablelength(mm)
Drilling depth(mm)
Settingdepth min.
(mm)88
10101212
M6M6M8M8
M10M10
4560608070
100
555560607070
51515251535
353540405050
Drill Ø(mm)
Size(mm)
Length(mm)
Usablelength(mm)
Drilling depth(mm)
Settingdepth min.
(mm)88
101010121212161616
M6M6M8M8M8
M10M10M10M12M12M12
406550759575
10013065
110145
5555606060707070909090
5255
30501540705
2560
3535404040505050757575
Plug & drill Ø(mm)
Length(mm)
UsableDrilling Depth(mm)
Length(mm)
SettingDepth Min.
(mm)5406060807001
555506060707
55151525153
535304040505
8801012121
2.53.35.58.0
90.0100.0120.0140.0
10.013.017.0---
10.013.015.019.0
8.025.040.050.0
4.205.30
12.8025.0
Distance to edge C (mm)
55.060.075.0
115.0
Tinst
*for cracked Concrete we shall use 0,5 x this value (approximately)
materials:- zinc plated and die-cast.
SSA
Cab
le t
ray
SyS
tem
S
59
Heavy Duty anchors
Size Threaded Length(mm)
Min. Drill Ø(mm)
Shield Length(mm)
Min. Hole Dep(mm)
Setting DepthH eff.
Usable Length(mm)
Spaner Size(mm)
M66580
11512 45 50 35
102560
10
M8
7590
115125
14 50 55 40
10255060
13
M1090
105135
16 60 65 50153060
17
M12110125170
20 75 85 60153075
19
b- Shield anchor with threaded bolt and nut:
Installation Parmeters:A- Using a hexagon screw: insert shield only, place the fixture over the hole and insert a hexagon screw with a washer through the fixture.B- Using a threaded bolt and nut: insert the shield with a threaded bolt, position the fixture over the thread and add a washer with a nut.
A- Shield anchor with hexagon screw:
SizeBolt Length
(mm)Min.Drill Ø
(mm)Shield Length
(mm)Min. Hole Depth
(mm)Setting Depth
H eff.Usable Length
(mm)Spanner Size
(mm)
M6557085
12 45 50 35102540
10
M8658095
14 50 55 40102540
13
M107590115
16 60 65 50102550
17
M1290105120
20 75 85 60102540
19
Installation
Throughbolt, stainless steel A4/316
serutaeFetercnocdekcarcnurof7noitpOlavorppAlacinhceTnaeporuE
Torque controlled expansionApplications in damp areas and outdoorsStainless steel A4/316Face xing or through xing
Applications ,senihcam,snoitcurtsnocleets,sgniliar,syartelbac,sedacaf
under-constructions, high-racks, pro les
Tension load (kN)
Shear load (kN)
Bending moment (Nm)
Edge Distance C (mm)
He�. (mm)
Distance betweenanchor S (mm)
Thickness offoundation
(mm)
Tighten torque(Nm)
Spanner size
6M 2.64.15.89.214
3.36.38.51223
5153050
100
5.513
26.546.5
118.5
4050586880
Washer (Ø)
12 x 1.616 x 1.620 x 2.024 x 2.530 x 3.0
02106 001 018M 05157 001 3101M 47178 021 7121M 402201 041 9161M 042021 061 42
noitallatsnI
2
03505604015660452086040459672505803010680501088055158805525980554511833506015301070185515901850301101855452101850604101850806101850010810194508218651011218603521218605541218607561218609581210701511610851031610803541610854061610856081610010306102
50 Mungo Befestigungstechnik AG
Plug & drill Ø(mm)
Length(mm)
UsableLength(mm)
Settingdepth min.
(mm)
kat_en-2007-11-29.indd 50 4.12.2007 10:12:24 Uhr
Bolt Size
Tinst
1
Drill a hole and clean it with a bruch, remove dust with a blower.
Throughbolt, stainless steel A4/316
serutaeFetercnocdekcarcnurof7noitpOlavorppAlacinhceTnaeporuE
Torque controlled expansionApplications in damp areas and outdoorsStainless steel A4/316Face xing or through xing
Applications ,senihcam,snoitcurtsnocleets,sgniliar,syartelbac,sedacaf
under-constructions, high-racks, pro les
Tension load (kN)
Shear load (kN)
Bending moment (Nm)
Edge Distance C (mm)
He�. (mm)
Distance betweenanchor S (mm)
Thickness offoundation
(mm)
Tighten torque(Nm)
Spanner size
6M 2.64.15.89.214
3.36.38.51223
5153050
100
5.513
26.546.5
118.5
4050586880
Washer (Ø)
12 x 1.616 x 1.620 x 2.024 x 2.530 x 3.0
02106 001 018M 05157 001 3101M 47178 021 7121M 402201 041 9161M 042021 061 42
noitallatsnI
2
03505604015660452086040459672505803010680501088055158805525980554511833506015301070185515901850301101855452101850604101850806101850010810194508218651011218603521218605541218607561218609581210701511610851031610803541610854061610856081610010306102
50 Mungo Befestigungstechnik AG
Plug & drill Ø(mm)
Length(mm)
UsableLength(mm)
Settingdepth min.
(mm)
kat_en-2007-11-29.indd 50 4.12.2007 10:12:24 Uhr
Bolt Size
Tinst
11
Drill a hole and clean it with a brush, remove dust with a blower.
Place the plug and the object to fix.
2
Tighten the screw.
3
Fixing completed.
4
Tighten the screw. Fixing completed.Place the plug and the object to fix.
2 3 4
ww
w.u
nim
etal
-ikk.
com
Cable maNaGemeNt SyStemSCable tray SyStemS
www.unimetal-ikk.com60
Ordering Cable Tray- Side Height Varieties - Abbreviations- How to Order- General Information
Cab
le t
ray
SyS
tem
S
61
Side Height Varieties
-Abbreviations
- Straight end Str
- Return flange outside rFO
- C - type outside CtO
- Return flange inside rFI
- C - type inside CtI
materials & Finishes
Stainless SteelPre-Galvanizedaluminium
Hot-dip GalvanizedElectrolytic GalvanizedPowder Coated
thickness
Sheet of 1.0 mmSheet of 1.20 mm Sheet of 1.50 mmSheet of 2.0 mmSheet of 5.0 mm
Code
SSPGal
HDeGPC
Code
12345
For more information on ordering and types, Uni-Metal technical staff are ready to assist you with all necessary details. www.unimetal-ikk.com
Cable trays are available in the following side heights:• 25 mm • 50 mm • 75 mm • 100 mm* Other side heights can be manufactured upon request.
Cable trays and accessories are available in the following side height types:
- Ordering Cable Tray
ww
w.u
nim
etal
-ikk.
com
Cable maNaGemeNt SyStemSCable tray SyStemS
www.unimetal-ikk.com62
Ordering Cable Trays & Accessories
-General Information
-Location of Couplers
- Item & Order Number for Sections & FittingsWhen ordering cable trays, the full order number shall include the material used, width of the tray, side height, type of side and the length of the tray.
Consideration shall be given to the following factors when undertaking the design of a cable tray run and a support system, although some of these (ex: wind loads) may not be relevant to every installation :
In practice, it is often difficult to pre-determine where the couplerswill be located within a straight run of a cable tray.However, it is worth making some efforts to roughly plan their position during the early stages of installation. The worst positions of the couplers are either at mid-span or immediately over a point of support; at these locations they will suffer the greatest stress.Both locations shall be particularly avoided at the end of an installation. From a practical viewpoint it is also more difficult to assemble or fix down a tray if the couplers are positioned immediately over the supports.The best position of joints in a continuous installation is one quarter of the span distance on either side of each point of support.
Examples:1- Order number for Hot-Dip Galvanized 2,400 mm length cable tray, 50 mm side height, 2mm sheet thickness and 500 mm width with outside return flange:
130 050 0500 4/rFO 2400 PG PC
2- Order number for Pre-Galvanized 3,000 mm length cable tray, 50 mm side height, 1.25 mm sheet thickness and 300 mm width with inside return flange:
110 050 0300 2/rFI 3000 PG PC
3- Order number for powder coated curved T-branch, 50 mm side height, 1.5 mm sheet thickness and 700 mm width with straight end:
320 050 0700 3/Str PG PC
N.B.: Order number for connectors will include the item number, side height and thickness of the sheet
• Distributed loads e.g. cables, pipes.• Point loads• Thermal expansion & contraction• Wind & external forces
• Spacing of supports• Safety factor• Deflection
S/4
S
Order Example
Length (mm)
SideType
Thickness(mm)
Width(mm)
Pre. Galvanized(Materials)
Powder Coated(Finishes)
ItemNumber
Side Height
PC
Cab
le t
ray
SyS
tem
S
63
ww
w.u
nim
etal
-ikk.
com
No
tes
Cable maNaGemeNt SyStemSCable tray SyStemS
www.unimetal-ikk.com64
No
tes