S1
Solvent-Switched In Situ Confinement Approach for Immobilizing
Highly-Active Ultrafine Palladium Nanoparticles: Boosting
Catalytic Hydrogen Evolution
Qi-Long Zhu,a Fu-Zhan Song,a Qiu-Ju Wang,a Nobuko Tsumori,c Yuichiro Himeda,d Tom
Autreye and Qiang Xu*a,b
aResearch Institute of Electrochemical Energy, National Institute of Advanced Industrial Science and Technology (AIST), Ikeda, Osaka 563-8577, JapanbAIST-Kyoto University Chemical Energy Materials Open Innovation Laboratory (ChEM-OIL), Yoshida Sakyo-ku, Kyoto, 606-8501, JapancToyama National College of Technology, 13, Hongo-machi, Toyama 939-8630, JapandResearch Institute of Energy Frontier, AIST, Tsukuba Central 5, 1-1-1 Higashi, Tsukuba, Ibaraki 305-8565, Japan ePacific Northwest National Laboratory, 902 Battelle Boulevard, Richland, Washington 99352, United States
Corresponding author. E-mail: [email protected]
Electronic Supplementary Material (ESI) for Journal of Materials Chemistry A.This journal is © The Royal Society of Chemistry 2018
S2
1. Chemicals and Materials
All chemicals were commercial and used without further purification. Palladium(II) acetate (Pd(OAc)2,
Wako Pure Chemical Industries, Ltd., >98%), potassium tetrachloropalladate (K2PdCl4, Wako Pure
Chemical Industries, Ltd., >97%), sodium borohyride (SB, NaBH4, Sigma-Aldrich, 99%), Maxsorb MSC-30
(Nanoporous Carbon, Kansai Coke and Chemicals Co. Ltd.), formic acid (FA, HCOOH, Kishida Chemicals
Co. Ltd., >98%), sodium formate dehydrate (SF, HCOONa, Sigma-Aldrich, 99.5%), acetone (Kishida Chem.
Co., >99.5%) were used as received. De-ionized water was obtained by reverse osmosis followed by ion-
exchange and filtration (RFD 250NB, Toyo Seisakusho Kaisha, Ltd., Japan).
2. Instrumentation
Laboratory powder X-ray diffraction patterns were collected for samples on Rigaku Ultima IV X-ray
diffractometer using Cu Kα radiation (λ = 0.15406 nm) (40 kV, 40 mA). The surface area measurements
were performed with N2 adsorption/desorption isotherms at liquid nitrogen temperature (77 K) using
automatic volumetric adsorption equipment (Belsorp-max) after dehydration under vacuum at 120 °C for 12
h. The metal content of the catalyst was analyzed using ICP-OES on Thermo Scientific iCAP6300. X-ray
photoelectron spectroscopic (XPS) measurements were conducted on a Shimadzu ESCA-3400 X-ray
photoelectron spectrometer using a Mg Kα source (10 kV, 10 mA). The charging potentials of the catalyst
samples were corrected by setting the binding energy of the adventitious carbon (C 1s) at 284.6 eV. The
TEM and HAADF-STEM images and energy-dispersive X-ray (EDX) spectra were recorded on
Transmission electron microscope (TEM, TECNAI G2 F20) with operating voltage at 200 kV equipped with
EDX detector. The gas generated from the dehydrogenation of formic acid was analyzed by GC-8A TCD
(molecular sieve 5A, Ar as carrier gas) and GC-8A TCD (Porapack N, He as carrier gas) analyzers
(Shimadzu), which was collected after purging the reactor with nitrogen three times. The detection limit was
below 10 ppm for CO.
3. Synthesis of Catalysts
3.1 Synthesis of the Pd2+@MSC pre-catalyst: Typically, 120 mg of Pd(OAc)2 was dissolved in 120 mL of
acetone in a beaker under vigorous stirring at room temperature. After stirring for 10 min, 500 mg of porous
carbon MSC was added and mixed for another 1 hour for sufficiently absorbing the metal precursor into the
carbon pores. Subsequently, the solvent and residual metal precursor were removed by centrifugation. The
collected solid was washed with anhydrous acetone twice only to avoid serious loss of the metal precursor in
the pores of MSC, while the metal precursor absorbed on the external surface can be easily removed. The
sample was finally dried under vacuum at room temperature to give the Pd2+@MSC pre-catalyst.
3.2 Synthesis of in situ-Pd@MSC and in situ-Pd/MSC: The in situ-Pd@MSC and in situ-Pd/MSC were in
situ reduced from the Pd2+@MSC pre-catalyst and the physical mixture of MSC and K2PdCl4, respectively,
in the FA dehydrogenation system. The detailed procedures are described in the section of catalytic activity
characterization.
S3
3.3 Synthesis of pre-Pd@MSC: 20 mg of NaBH4 was dissolved in 2.0 mL of water, to which 100 mg of the
Pd2+@MSC pre-catalyst was added under vigorous stirring. After stirring for 10 min, the solid was collected
by centrifugation, washed with de-ionized water three times and dried under vacuum at room temperature.
4. Catalytic Activity Characterization
4.1 Procedure for hydrogen evolution from formic acid: The Pd2+@MSC pre-catalyst (100 mg) was
placed in a two-necked round-bottomed flask (30 mL), which was placed in a water bath at a preset
temperature (30-60 °C) under ambient atmosphere. A gas burette filled with water was connected to the
reaction flask to measure the volume of released gas (lab temperature kept constant at 25 °C during
measurements). The Pd2+@MSC pre-catalyst was firstly reduced when 2.5 mL of the mixed aqueous
solution containing 9 mmol FA and 9 mmol SF was injected into the mixture, which is followed by gas
evolution catalyzed by the in-situ-generated catalyst denoted as in situ-Pd@MSC. The volume of the
released gas was monitored by recording the displacement of water in the gas burette.
The activity evaluation of the in situ-Pd/MSC catalyst for hydrogen evolution from FA was performed
using the similar procedure as described for in situ-Pd@MSC. 200 mg of MSC was ultrasonically dispersed
in 1.0 mL of water in a two-necked round-bottomed flask (30 mL) and subsequently mixed with 29.5 mg of
K2PdCl4. The resulted aqueous suspension was further homogenized under sonication conditions for half
hour. The in situ-Pd/MSC catalyst was generated when 1.5 mL of the mixed aqueous solution containing 9
mmol FA and 9 mmol SF was injected, which is followed by catalytic gas evolution.
After the reaction, the catalysts were separated from the reaction solution by centrifugation, washed with
water, and dried under vacuum at room temperature for the XPS, PXRD and TEM analyses.
4.2 Durability testing of the catalysts: For testing the durability of the catalyst, a new batch of pure FA
(0.34 mL, 9.0 mmol) was subsequently added into the reaction flask after the completion of the first-run
dehydrogenation of FA. Such test cycles of the catalyst for the dehydrogenation of FA were carried out for 5
runs at 60 °C by adding aliquots of pure FA.
4.4 Calculation Methods: The turnover frequency (TOF) reported here is an apparent TOF value based on
the number of Pd atoms in catalyst, which is calculated from the time of half-completion of gas generation,
and the equation as follows:
Where Patm is the atmospheric pressure (101325 Pa), Vgas is the generated volume of H2/CO2 gas at the time
of half-completion of gas generation, R is the universal gas constant (8.3145 m3 Pa mol-1 K-1), T is the room
temperature (298 K), nPd is the total mole number of Pd atoms in catalyst, and t is the time of half-
completion of gas generation.
S4
Fig. S1 EDX spectrum of the bulk solid of in situ-Pd@MSC from TEM measurement. The copper signal
originates from Cu grid.
Fig. S2 TEM images of pre-Pd@MSC.
S5
Fig. S3 TEM images of in situ-Pd/MSC.
S6
Fig. S4 Gas chromatograms of CO, air and H2 as reference gases and the released gas from FA
dehydrogenation over in situ-Pd@MSC (nPd/nFA= 0.0048, 60 °C), showing the presence of H2 and the
absence of CO in the released gas.
Fig. S5 Gas chromatograms of CO2 as reference gas and the released gas from FA dehydrogenation over in
situ-Pd@MSC (nPd/nFA= 0.0048, 60 °C), showing the presence of CO2 in the released gas.
S7
Fig. S6 The comparison of the volume of the gas released during the in situ-Pd@MSC catalyzed
dehydrogenation of FA (FA:SF = 1:1, nPd/nFA = 0.0048) at 30 C (a) with and (b) without the trap (10 M
NaOH solution).
Fig. S7 Recyclability test for hydrogen evolution from FA over the in situ-Pd@MSC catalyst (FA:SF=1:1,
nPd/nFA= 0.0048, 60 °C).
S8
Fig. S8 Volume of the generated gas (CO2 + H2) versus time for hydrogen evolution from FA with different
FA/SF molar ratios in the presence of the Pd2+@MSC pre-catalyst (nPd/nFA= 0.0048, 60 °C).
Fig. S9 Volume of H2 versus time for hydrogen evolution from aqueous SF over the in situ-Pd@MSC
catalyst (nPd/nSF= 0.0048, 60 °C).
S9
Table S1. Surface areas and pore volumes of MSC, Pd2+@MSC and in situ-Pd@MSC
Sample BET surface area (m2 g-1) Total pore volume (cm3 g-1)
MSC 2765 1.540
Pd2+@MSC 2233 1.231
in situ-Pd@MSC 2392 1.308
S10
Table S2. Catalytic activities for dehydrogenation of formic acid catalyzed by selected outstanding
heterogeneous catalysts
Catalyst Medium Temp. (°C) CO evolution TOF (h-1) Ref.
In situ-Pd@MSC FA–SF 60 No 9110 This work
Pd/C_m FA–SF 60 No 7256J. Am. Chem. Soc., 2015, 137, 11743
Pd/PDA-rGO FA–SF 50 No 3810ACS Catal. 2015, 5, 5141
Pd/S-1-in-K FA–SF 50 10 ppm 3027J. Am. Chem. Soc., 2016, 138, 7484
(Co6)Ag0.1Pd0.9/RGO FA–SF 50 No 2739J. Am. Chem. Soc., 2015, 137, 106
Pd/MSC-30 FA–SF 50 No 2623Chem. Sci., 2014, 5, 195
Pd-B/C FA–SF 30 No 1184J. Am. Chem. Soc., 2014, 136, 4861
Au/ZrO2 NCs FA–NEt3 50 No 1593J. Am. Chem. Soc., 2012, 134, 8926
Pd/basic resin FA–SF 75 5 ppm 820ACS Catal., 2013, 3, 1114
Ag42Pd58 FA 50 No 382Angew. Chem. Int. Ed., 2013, 52, 3681
Ag@Pd/C FA 20 No 192Nat. Nanotechnol., 2011, 6, 302
PdAu/C-CeO2 FA–SF 92 145 ppm 113.5Chem. Commun., 2008, 3540
AuPd@ED-MIL-101 FA–SF 90 Yes 106J. Am. Chem. Soc. 2011, 133, 11822
Co0.30Au0.35Pd0.35 FA 25 No 80Angew. Chem. Int. Ed., 2013, 52, 4406
PdAu@Au/C FA–SF 92 30 ppm 21.4Chem. Mater., 2010, 22, 5122