94
Corken Pumps
Corken “C Series” Coro-Flo Pumps
Corken Coro-Flo Regenerative Turbine Pumps
Model Number
CapacityGPM Propane Inlet Outlet
MotorHP
ShippingWeight
C10-SM 7 1-1/4” 1” 1 - 1 Phase 80#
C12-SM 12 1-1/2” 1” 1 - 1 Phase 90#
C13-SM 20 1-1/2” 1” 2 - 1 Phase 130#
C14 38 1-1/2” 1” 3 - 3 Phase 150#
Extremely quiet and free of vibration and pulsation, the Coro-Flo pump provides trouble-free service and long life. For low-capacity, medium-head pumping such as cylinder filling, the C-Series is the pump of choice.
The regenerative turbine pump is the most dependable LP gas pump on the market. The free floating impeller with teeth cut on both sides picks up the fluid and creates a spiraling motion around the circumference of each side. The fluid is slightly ac-celerated and pressurized in dozens of small steps creating a smooth, quiet, overall product flow. With only a single pump seal and it’s free-floating impeller, the main-tenence on these pumps is easy and very infrequent.
Model Number
CapacityGPM Propane Inlet Outlet
MotorHP
ShippingWeight
F10 7 1-1/4” 1” 3/4
48#
F12 12 1-1/2” 1” 1
F13 20 1-1/2” 1” 2
F14 38 1-1/2” 1” 3
F15 19 1-1/2” 1” 3
Model Number
Capacity*GPM Propane Inlet Outlet
MotorHP
ShippingWeight
FF075 32 1-1/2” 1” 7.5140#
FF150 44 1-1/2” 1” 7.5
Corken “F Series” Coro-Flo Pumps
Corken “FF Series” Coro-Flo Pumps
CORKEN
CORKEN
Same features and reliability as the “C” models but used for base mounting with standard foot mounted motors. Motor volt-age, phase etc. can be selected to suit the individual application. Commonly used to feed vaporizing and aerosol systems.
The FF075 and FF150 pumps are designed for larger capacity or higher differential pressure applications. Exceptionally well suited for larger motor fuelling, vaporizer feed systems in both aboveground and underground tank applications.
C12
F12
FF075
Typical Mounting
CORKEN
CORKEN
95
150
USG
200
250
300
100
50
BG
PAET
INLE
T
OUTLET
CORKEN
CORKEN
Corken Coro-Vane Stationary Pumps
Corken Coro-Vane Sliding Vane Pumps
Corken Coro-Vane pumps utilize the sliding-vane design to ensure pumping efficiencies remain high throughout the life of the pump. The vanes are self-adjusting for wear. Coro-Vane pumps are positive displacement pumps. They produce up to a maximum differential pressure of 125 PSIG. Three models are offered with capacities up to 350 GPM.
The sliding vane pump is the most popular type of pump in the LP gas industry for higher flow rate applications. In this type of pump, a slotted rotor is eccentrically sup-ported in a cycloidal cam creating a crescent cavity between the rotor and the cam. The sliding vanes sweep the incoming fluid to the opposite side of the crescent where it is squeezed through discharge holes in the cam toward the pump outlet.
Because the vanes must always firmly contact the cam, special porting is designed into these pumps which routes discharge pressure under the vanes to keep them retracted from the rotor.
Corken Pumps
INLE
T
OUTLE
T
Model Number
Capacity*GPM Propane Inlet Outlet
Motor STD HP
ShippingWeight
521 72 2-1/2” NPT 2” NPT 5 132#
Z3500 154 3” NPT 3” NPT 10 160#
Z4500 310 4” Flange 3” Flange 20 265#
* Capacity based on 780 RPM and 40 PSID.** Other inlet and outlet configurations available on request.
Z3500
Typical Z3500 Installation
96
Corken Pumps
Corken Coro-Vane Truck PumpsThe Corken Z-Series truck pumps offer some remarkable improvements over competitive designs.Rotor Centering - thrust bearings in addition to heavy duty roller bearings keep the rotor from grinding thru the endplates.Blade Life - large diameter, low mass blade drivers won’t drive thru the blades even at elevated speeds.Cavitation - new design blades, push rods and liner allow speeds up to 800 RPM.
Model Number
Capacity*GPM Propane Inlet
AuxilliaryInlet Outlet
ShippingWeight
Z3200 121 3” Flange 2” NPT 2” NPT 140#
Z4200 400 4” Flange 2” NPT Dual 2” NPT 275#
* Capacity based on 800 RPM and 50 PSID.
INLET
OUTLET
CORKEN
CORKEN
Z3200 Bobtail PumpEnd View
Z3200 Bobtail PumpMounted on Internal Valve
Z4200 Transport PumpMounted on Internal Valve
Z3200 Bobtail PumpSide View
Z4200Transport Pump
INLET
OUTLET
CORKEN
CORKEN
OUTLET
INLET
Rego
Rego
Rego
R
CORO-VANE
Rego
Typical Transport Mounting4” Z4200
97
Corken Pumps
Corken Flo-Chek ValvesThe Flo-Chek enables you to detect flow in gas or liquid lines and prevents release of product from storage tank in the event of a line failure. Flow-indicating and back-check valves feature all ductile iron construction and are available in 1-1/4” through 4” NPT or 2” through 4” slip-on weld flange configurations.
FC200
Model Number
Inlet &Outlet
ShippingWeight
FC125 1-1/4”8#
FC150 1-1/2”
FC200 2”30#
FC250 2-1/2”
FC300 3”40#
FC400 4” No Flow Erratic Flow Full Flow
Reading The Flo-Chek Valve
Corken Pump Bypass ValvesB166 SeriesThe B166 is used on cylinder filling pumps as well as aerosol feed pumps. It incorporates a priming valve for vapor elimination and operates with a moderate pressure build-up.
T166 SeriesThe T166 is used on larger capacity pumps such as bulk delivery trucks. It incorporates a continuous internal bleed for vapor elimination and operates with a moderate pressure build-up.
B177 SeriesThe B177 is used on large capacity pumps. It requires an external sensing line and operates with a low pressure build-up.
B166, T166
B177
ZV200
Typical BypassArrangement
Model Number
Capacity RangeGPM Propane
Inlet &Outlet
ShippingWeight
B166 3/4 Up to 40 3/4”
9#B166 1 Up to 40 1”
T166 1-1/4 30 - 100 1-1/4”
T166 1-1/2 30 - 100 1-1/2”
ZV200 70 - 250 2” 23#
B177 280 - 350
2”45#
B177 2-1/2 2-1/2”
ZV200 BypassThe ZV200 is used on both truck and stationary applications. It incorporates continuous internal bleed for vapor elimi-nation and operates with low pressure build-up.
I N L E T
CORKENR
ZV200 BYPASSVALVE
Inlet
To Load
Return to Tank
98
Corken Oil-Free CompressorsCorken gas compressors are designed for use in liquid transfer, vapor recovery, scavenger and portable applications. Whether it is gas recovery from cylinders or barge unloading, Corken has a com-pressor for your application.
The “107” bulk plant gas compressor unit is complete with pres-sure gauges, steel baseplate, mechanical liquid trap, four-way valve, strainer, interconnecting piping, adjustable driver slide base, v-belt drive and belt guard ready to receive an electric motor. This standard unit is typically used for liquid transfer and vapor recovery in applications including rail car and truck loading and unloading.
Corken Pumps
491-107
Model Number
Max CapacityGPM Propane
Max CapacityCFM Inlet Outlet
Motor STD HP
BareWeight
“107”Weight
91 50 8.3 3/4” NPT 3/4” NPT 5 145# 260#
291 101 16.5 3/4” NPT 3/4” NPT 5 190# 305#
491 215 35.5 1-1/4” NPT 1-1/4” NPT 15 300# 480#
691 361 60.2 2” NPT 1-1/2” NPT 25 670# 850#
Typical Compressor Transfer System
Tank Car Nipples with IntegralEmergency Shutoff
Emergency Shutoff
Check Valves
Sight FlowBack Check
99
Blackmer Pumps
Blackmer Cylinder & Motor Fueling PumpsThese motor speed pumps are positive displacement sliding-vane design in a wide range of capacities. “F” series models include a motor mount-ing bracket for close coupling to NEMA C-face motors.1” models incorporate an integral back-to-tank bypass.
Model Number
Capacity*GPM Propane
Inlet &Outlet
MotorHP
MotorMounting
ShippingWeight
LGF1 8 1” 1 C-face 32#
LGF1P 13 1-1/2 C-face 32#
LGRLF1.25 16
1-1/4” 1-1/2
C-face 43#
LGLF1.25 21 C-face 43#
LGL1.25 21 Foot 31#
LGL1.5 33 1-1/2” 3 Foot 31#
LGF1P
LGF1Pwithmotor
LGL1.5
LGRLF1.25
Blackmer Stationary Pumps
Model Number
Capacity*GPM Propane Inlet Outlet
Motor STD HP
ShippingWeight
LGLD2E 67 2” NPT 2” NPT 5 60#
LGLD3E 133 3” NPT 3” NPT 10 166#
LGLD4 270 4” Flange 3” Flange 20 227#
* Capacity based on 660 RPM and 50 PSID.** Other inlet and outlet configurations available on request.
* Capacity based on cylinder filling applications.
Blackmer stationary pumps are positive displacement design utiliz-ing sliding-vanes. Three models offer ranges up to 270 GPM. These are higher volume pumps that are commonly driven at reduced speeds with V-belt drives.
LGLD4
LGLD2E
Blackmer Truck PumpsBlackmer TLGLF3 and TLGLF4 pumps are designed to mount directly to a commercial internal control valve, in combination with the tank of a bobtail or transport.
Model Number
Capacity*GPM Propane Inlet
AuxilliaryInlet Outlet
ShippingWeight
TLGLF3 93 3” Flange 2” NPT 2” NPT 125#
TLGLF4 280 4” Flange 2” NPT Dual 2” NPT 240#
* Capacity based on 650 RPM and 50 PSID.
TLGLF3
TLGLF4
100
Checking the performance of a liquid propane pump is readily accomplished by recirculating the product flow and throttling the discharge to determine the pressure capability of the system. The pump should be able to increase the tank pressure by at least 80 psi without motor overload or pressure fluctuation.
Pump Accessories
Blackmer Bypass Valves
Pump Checkout Procedure
Blackmer differential bypass valves are designed to protect pumps and system components from excessive pressure damage. Five sizes are offered to provide full flow capacity up to 250 GPM.
Valve “A” must be open. Verify that the excess flow valve has not inadvertently closed.
The filling hose must be connected to valve “C” to allow free circulation back to storage.
Valve “B” must be closed to eliminate the bypass circuit.
Pressure gauge “D” will show tank pressure with the pump off. It will read a modest (20 psi) increase in pres-sure after pump is started with valve “C” open
Throttling valve “C” will dead head the flow and allow the operator to judge the highest pressure increase the pump is capable of producing.
Reopening valve “B” will allow the operator to do a final reset of the bypass valve.
Model Number
Capacity RangeGPM Propane
Inlet &Outlet
ShippingWeight
BV 3/4Up to 40
3/4”5#
BV 1 1”
BV 1-1/4Up to 80
1-1/4”10#
BV 1-1/2 1-1/2”
BV 2 Up to 180 2” 16#
BV2
If the system doesn’t have a pressure gauge, install one.If the filling hose is too short to provide recirculation, get a longer one.
Fisher Absolute Bypass ValvesCertain applications require a set line pressure that does not vary with the pressure of the storage tank. Absolute bypasses measure the difference between the line pressure and atmo-spheric pressure and fill the need for this type of application.
98H-30
Model Number
SpringRange
Inlet &Outlet
*Propane Capacity (GPM)
ShippingWeight
98H-30 70 - 140# 1” 49.0 20#
98H-9650 - 100#
1-1/2”28.0
37#
98H-100 2” 48#
* Based on 10 psig buildup over setting.
CORKEN
A
C
D
B
101
Steel Flex Connectors
InsideDiameter
OverallLength
WorkingPressure PSI
BurstPressure PSI
1/2” 12” 2350 9400
3/4” 13” 1335 5340
1” 14” 1120 4480
1-1/4” 15” 800 3200
1-1/2” 16” 665 2660
2” 20” 865 3460
2-1/2” 22” 495 1980
3” 24” 455 1820
Steel Flex Connectors are used in piping systems where settling and shifting would cause stresses on the piping components. Also used to dampen the vibration in pump and compressor systems.The stainless steel inner tube is wrapped with double braided stainless steel. Schedule 80 nipples are welded on.
These are standard diameter and length flex connecors.Other lengths available by special order.
Flanged models are available by special order. The flexible material is the same as the threaded models. Order by connector diameter and face-to-face dimension.
2” Flex ConnectorThreaded
2” Flex ConnectorFlanged
Standard Threaded Specs
Flanged Connectors
Standard Threaded Specs
Standard Flanged Specs
GPA
ET
Pump Accessories
Paget StrainersDesigned to trap foreign material in pipeline systems and retain it in the strainer body where it is removed through the blow-off connec-tion. All strainers are ductile iron (1000 WOG) in accordance with the guidelines of NFPA 58. Screens are 40 mesh stainless steel. Stocked in 1/2” thru 3” screwed sizes.Flanged connections available on special order.
Flanged models have 300# flanges both ends.
Pag 2
Pag 4F
Part No Size FNPT Blow-off FNPT Size A
PAG 1/2 1/2”1/2” 3-7/8”
PAG 3/4 3/4”
PAG 1 1”3/4”
5”
PAG 1-1/4 1-1/4” 5-1/2”
PAG 1-1/2 1-1/2”1”
6”
PAG 2 2” 7-1/4”
PAG 3 3” 1-1/4” 10”
Part No Size Blow-off FNPT Size A
PAG 2F 2” 1” 11-1/4”
PAG 3F 3” 1-1/4” 14”
PAG 4F 4” 1-1/4” 17”
PAG 6F 6” 1-1/2” 21-1/2”
A
A
BG
PAET
102
Motors and Drive AccessoriesWe stock a complete line of AC electric motors, direct drive accessories, V-belt drive accessories, starters and start-stop stations. Give us a call for your particular application needs.Motors: Explosion proof models for pumps and compressors thru 25HP.V-belt Drives: Hubs and sheaves to match any RPM needs.Direct Drive Couplings: Couplings and spiders for all popular drive shaft sizes.Starters: Explosion proof manual and magnetic starters with accessory start-stop stations.
Explosion Proof Motors
V-belt Hubs and Sheaves
Direct Drive Couplings
Manual Motor Starters Start-Stop Stations Magnetic Starters
OUTLET
INLET
C O R K E N
CORKEN
V-belt Drive PumpDirect Drive Pump
Pump Accessories
103
Pump Hook-up Kits
Filling Hook-up KitsBottle Fill Kit ComponentsPump with Motor & SwitchBypass ValveBottom Outlet Valve with Excess FlowHydrostatic ReliefFlex ConnectorStrainerInlet Pipe Union & Nipples1/2 X 10 ft Filling HoseQuick Acting Shutoff ValveSoft Nose POL Connector
Motor Fuel Fill Kit ComponentsSame componnents as the Bottle Fill except:3/4” X 15 ft Filling HoseQuick Acting Shutoff ValveFemale ACME Connector
You Supply The Tank - We Will Send The Rest
Pressurizing Pump Sets
Differential Pressure Applications Absolute Pressure Applications
We assemble complete pressurizing pump sets for a wide variety of pressure and load requirements. These assemblies provide a complete pump pressurizing package for continuos duty service with all components prepiped on a common base for ease of installation.
UL
BG
PAET
400WOG
Motor Fuel KitHose End Valve
Fill KitPiping
Arrangement
150
USG
200
250
300
100
50
Return ToStorage
ToLoad
BG
PAET
150
USG
200
250
300
100
50
This style pump set is used where an absolute line pressure is required by the load. The absolute bypass holds the delivery pressure to a constant value in contrast to a differential value.
Common applications include hot mix plants, propane air mixers or any vaporized gas application where a steady pressure is required.
This style pump set is used where the load requires a moderate boost in pressure above what the storage tank can provide. A differential bypass regulates the boost pressure. The dual check valve arrangement allows the load to operate without the pump running with the option of runing the pump when low storage tank pressures are experienced.
Common applications include grain dryers, construction heater loads or any vaporized gas application requiring a presssure boost.
ToLoad
Return ToStorage
In
104
Dispensing Units
Standard Dispensing Units
Standard Dispensing Unit
Profitable, Ready To Use “Gas-Pac”Designed to service the growing need for LP fuel to industrial forklift users, motor fleets, campers, sportsmen and many others. The “Gas-Pac” unit is ready to use and will service all types and sizes of cylinders and tanks.
• 12 GPM Pump with explosion proof motor listed by U.L.• Neptune 1” meter with 631 register.• 3/4 X 18 ft motor fuel hose• 1/2 X 5 ft cylinder filling hose• 1000# platform scale• Inlet strainer• All metal welded constuction• Locking door• Refill, Haz-Mat, Propane & No Smoking decals
Features
Options• Temperature compensated meter• Skid for tank mounting
SpecificationsDepth 40”Width 40”Height 45”Weight 250#
Deluxe Walk-in Dispensing Units
Deluxe Walk-in Dispensing Unit
Profitable, Ready To Use “Gas-Pac”The Deluxe Walk-in “Gas-Pac” is ready to use and provides out-of-the-elements filling for the operator. Large cabinet allows addition of an accessory explosion proof light if desired.
• 12 GPM Pump with explosion proof motor listed by U.L.
• Neptune 1” meter with 631 register.• 3/4 X 18 ft motor fuel hose• 1/2 X 5 ft cylinder filling hose• 1000# platform scale• Inlet strainer• All metal welded constuction• Locking door• Refill, Haz-Mat, Propane & No Smoking
decals
Features
Options• Temperature compensated meter• Skid for tank mounting• Emergency shut-off interlock assembly activated by door closure• Explosion proof light
SpecificationsDepth 48”Width 48”Height 72”Weight 500#
CORKEN
400
WOG
CORKEN
400
WOG
105
Dispensing Units
Dispensing Unit Skid BasesWe fabricate heavy duty skid bases for dispensing units to accomodate 500 or 1000 gallon tanks on a common base with the unit. A skid unit is much easier to install and gives the installation a professional look. The elevated tank mounting adds to the pump suction head for better pumping and long life of the dispenser components.
Cylinder Filling Connectors
ACME Filling Connectors
Dispenser Inlet Piping
7193D-10 POL
3175 A7575L3
7193L-10A Lift Truck
7193U-10 QCC
7193T-10 FPOL X QCC
12982 & 5760AFPOL X F Liquid
PROPANE
CORKE
N
400WOG
DISTANCE SET TO TANK FOOT CENTERS
SKID BASE DIMENSIONS
18' 6"
4' 0"
32"
END VIEW
19-1/4"
32"
SKID BASEISOMETRIC VIEW
BG
PAET
CabinetWall
106
Krug Products
Krug Vapor CompressorDesigned for evacuating tanks for repair or moving.Unit is portable. Easy to handle.Saves wear and tear on truck pump.4 HP overhead valve engine.18 to 50 GPM depending on piping.Gasoline or propane carburetion models.1/2” FNPT inlet and outlet connections.Shipping weight 70 lbs.
GXHONDA
H50-GH Compressorwith gasoline carburetion
H50-LPH Compressorwith propane carburetion
Krug Hand PumpUsed for liquid transfer where electicity is not available. The piston style, hand operated pump is easy to use and economical to maintain.6 GPM at 40 strokes.1” FNPT inlet and 3/4” FNPT outlet.
400WOG
Hand Pump shown with typical piping arrangement.
Hose KitsAvailable for tank-to-tank ortank-to-truck hookups.
STRAINER
10752 Typical Unloading Arrangement
Tank to Truck