COURSE CONTENT AND RESOURCES
1.SEMESTER
EEM 101 Fundamentals of Electrical and Electronics Engineering-1 (3-0) 3 5
Unit systems. Definition of electricity. Conductors and insulators. Effects of electrical current,
definition and measurement of current, voltage and resistance. Definition of Direct Current
(DC), Effect of heat on resistance. Calculation of equivalent resistances, Star-delta resistance
transformations, Definition of non-linear resistance, Kirchhoff’s Laws, work and power.
Thermal energy-electrical energy conversion, Energy loss and voltage drop in lines, Equivalent
circuit of voltage source, series and parallel connection of the voltage source, Maximum power
theorem. Thevenin’s and Norton’s equivalents of sources. Source transformation. Thevenin’s
and Norton’s theorems. Superposition theory, the series and parallel connections of capacitor
and behavior of capacitor in DC. Magnetic circuits. Structure and definition of inductance.
Series and parallel connection of inductance, behavior of inductance in DC, chemical effect of
current. Battery and accumulator.
Course book:
J. David Irwin, R. Mark Nelms, Basic Engineering Circuit Analysis, 11th Edition,Wiley
H. S. Selek, Doğru Akım(DC) Devre Analizi, Seçkim Yayıncılık, 2013
Supplementary course book:
D.E. Johnson, J.R. Johnson, J.L. Hilburn, and P.D. Scott, Electric Circuit Analysis, third
edition, Prentice Hall, 1997.
EEM 103 Introduction to Electrical and Electronics Engineering (1-0) 1 4
The fields of study of electrical and electronics engineering, historical development and general
information about the scientists who contributed to the field. Information about tools and
methods used in the field of Electrical and Electronics Engineering. Introductory information
about the fields of work of Electrical and Electronics Engineering. Interaction of electrical and
electronics engineers with other branches of science and engineering. Engineering ethics.
Knowledge transfer from experienced engineers.
Course book:
D. Ashby, H.H. Erkaya, Elektrik Mühendisliği 101, Nobel Akademik Yayıncılık, 2013
EEM 105 Mathematics-I (4-0) 4 5
Real numbers, complex numbers, matrices, determinants, Linear equation systems, functions
and function types, Basic elementary functions, Algebraic functions, Number arrays and the
limit of an array. Limit of a function and unilateral limits, Continuity and properties of
continuous functions.
Course book:
Genel Matematik, M. Balcı, 4. Basım, 2006.
Supplementary course book:
Yüksek Matematik Cilt.1-2-3, A.A.Karadeniz, Çağlayan Yayınevi, İstanbul, 2003.
Temel ve Genel Matematik I-II, Prof.Dr. H.Hilmi Hacısalihoğlu
EEM 107 Physics-I (2-2) 3 5
Physics and measurement, Motion in one dimension, Vectors and analysis of vectors in three
dimensions, Motion in two dimensions, Motion laws, Circular Motion, Work and kinetic
energy, potential energy and energy conservation. Linear momentum and collisions, Rotation
of rigid bodies around a fixed axis.
Course book:
Fen ve Mühendislik için Fizik I (Mekanik), R. A. Serway; Çeviri Editörü: Kemal
Çolakoğlu, (5. baskıdan çeviri), Palme Yay., 2002
Fizik I (Mekanik), F. J. Keller, W. E. Gettys, M. J. Skove, Çeviri Editörü: R. Ömür Akyüz,
Literatür Yay., 2006
Supplementary course book:
Modern Üniversite Fiziği, Cilt-1(Mekanik), Çevirisi: Prof. Dr. Fahri Domaniç, Prof. Dr.
Enis Erdik, Prof. Dr. N. Zengin, Çağlayan Kitabevi ,2000
EEM 109 General Chemistry (2-0) 2 5
Chemistry and substance, Symbols, formulas and equations. Gases and solids, Chemical
Thermodynamics. Reaction Rate and Equilibrium. Solutions, Equilibrium in Aqueous
Solutions, Periodic system and electron structure of atoms, Chemical Bond. Atomic core.
Periodic System-S Block, Periodic System-P Block, Periodic System-D and -F Block, Organic
Chemistry, biochemistry, electrochemistry.
Course book:
Petrucci, H.R., Harwood, S.W., Genel Kimya Çev. Uyar. T., Palme Yayıncılık, 1995,
Ankara.
Aydın, A.O., Sevinç, V., Şengil, İ.A., Temel Kimya Aşiyan Yayınları, 2001, Adapazarı
Supplementary course book:
Aydın, A.O., Sevinç, V., Şengil, İ.A., Temel Kimya Aşiyan Yayınları, 2001, Adapazarı
AIITL 101 Atatürk's Principles and History of Turkish Revolution I (2 + 0) 2 2
The decline and fall of the Ottoman Empire. Imperial edict of reorganization, I. and II.
Constitutionalism, Tripoli and Balkan Wars, World War I, Armistice of Mudros, Wilson
Principles, Paris Conference, Mustafa Kemal Pasha's arrival in Samsun and the situation in
Anatolia. Amasya Circular, National Congresses, Opening of Parliament Opening of the
Parliament. The establishment of the Grand National Assembly of Turkey (TBMM) and interior
riots. Constitution. Establishment of Regular Army. Inonu War I, Kütahya-Eskişehir and
Sakarya Battles and the Great Offensive, Treaties of the Turkish War of Independence,
Abolition of the Sultanate, Lausanne Peace Treaty, Proclamation of the Republic.
Course book:
Atatürk İlkeleri ve İnkılap Tarihi, Refik Turan, Gazi Kitapevi, Ankara,2005
Supplementary course book:
Nutuk
Erollu, H., Atatürk İlkeleri ve İnkılap Tarihi, Atatürkçülük.
Atatürk İlkeleri ve İnkılap Tarihi, Atatürkçülük, (YÖK yayını). Karıl, E.Z., Atatürk İlkeleri
ve İnkılap Tarihi, Atatürkçülük.
TDL 103 Turkish Language-I (2-0) 2 2
Characteristics of Turkish in terms of structure and meaning. Basic literary works. Self-
expression in society. Correct and effective ways of using the language.
Course book:
Akerson, F. (2008). Türkçe Örneklerle Dile Genel Bir Bakış, Multilingual, 2. Bsk. İstanbul,
282 s.
Supplementary course book:
Aksan, D. (1990). Her Yönüyle Dil Ana Çizgileriyle Dilbilim, TDK, Ankara,
YDL 105 Foreign Language I (2+0) 2 2
Nouns, Articles, Personal Pronouns, Possessive Adjectives, Verb “To Be”. Possessive “s”,
Asking For Names, Prices & Jobs. Some, Any, No, Every. Countable, Uncountable Nouns.
Cardinal and Ordinal Numbers, “What Time Is It?” Dates. Prepositions of Time and Place,
Present Progressive, Questions Forms, Questions Words, Imperatives, Present Simple,
Comparison of Present Simple and Present Continuous.
Course book:
Headway Intermediate, Jonh&Liz Soares, Oxford Univ. Pres, 1987.
Headway Upper Intermediate, John&Liz Soares, Oxford Univ. Pres, 1987.
2.SEMESTER
EEM 102 Fundamentals of Electrical and Electronics Eng.-II (3-0) 3 5
This course includes alternating current, definition of alternating current, the average and
effective values, phasor diagram, AC analysis of RL, RC and RLC circuits, circuit analysis
using the superposition, Mesh currents, Thevenin and Norton theorems, serial and parallel
resonance, three-phase systems.
Course book,
J. David Irwin, R. Mark Nelms, Basic Engineering Circuit Analysis, 11th Edition,Wiley
H. S. Selek, Alternatif Akım(DC) Devre Analizi, Seçkim Yayıncılık, 2013.
Supplementary Course book,
Abdullah Ferikoğlu, Devre Analizi I-II, Değişim Yayınları, Adapazarı, 2003.
EEM 104 Computer Programming (2-2) 3 5
This course will use to define a variable and input/output functions in C programming. Topics
include program flow control (IF ELSE, SWITCH CASE statements), loop operations (FOR,
WHILE, DO WHILE statements), structures, identification of array structures (one dimensional
and multidimensional arrays), function definition and calling operations.
read/write operations to a text file.
Course book,
H. M. Deitel and P. J. Deitel, 2006-2010, C: How to Program, Prentice Hall, International
Edition, ISBN: 0-13-089572-5
Supplementary Course book,
J.R.Hadly , E.B.Koffman, Problem Solving & Program Design in C, 2000, Addison-
Wesley
EEM 106 Mathematics-II (4-0) 4 6
This course includes derivative, its geometric semantics and properties, derivatives of basic
elementary functions, differential and higher order derivatives, derivative applications,
fundamental theorems related to derivative, analysis of functions and drawing of its graphs,
indefinite integral and its properties, variable change method, partial integration method,
integrals of rational and irrational functions, binomial integral, integral of trigonometric and
hyperbolic functions, definite integral, applications and properties of definite integral,
calculation of area, volume and arc length.
Course book,
Matematik Analiz-II, S. Çelik, S.A. Çelik, Birsen Yayınevi, İstanbul, 2008.
Genel Matematik I, Mustafa Balcı, Balcı Yayınları, İstanbul.
Supplementary Course book,
Yüksek Matematik Cilt.1-2-3, A.A.Karadeniz, Çağlayan Yayınevi, İstanbul, 2003.
EEM 108 Physics-II (2-2) 3 6
Electric charge, conservation and quantisation of charge, problem solving, Coulomb's Law,
electric field, electric field due to continuous charge distribution, motion of charge particles in
uniform electric fields, Gauss Law, electric potential, capacitors and dielectrics, energy stored
in a charged capacitor dielectric, Current and Resistance, Direct Current Circuits.
Course book,
Frederick J. Bueche, David A. Jerde, Fizik İlkeleri II; Raymond A. Serway, Fen ve
Mühendislik için Fizik. Frederick J. Keller, W.Edward Gettys, Malcolm J. Skove, Fizik2
Supplementary Course book,
Raymond A. Serway, Physics for Scientists & Engineers
AIITL 102 Atatürk's Principles and History of Turkish Revolutions-II (2+0) 2 2
Atatürk Period’s Turkish Revolution Movements, Turkish Foreign Policy During the Atatürk
Period, World War II and Foreign Policy of Turkey, Atatürk’s Principles, Turkey after
Atatürk's reforms.
Course book,
Atatürk İlkeleri ve İnkılap Tarihi, Refik Turan, Gazi Kitapevi, Ankara, 2005.
Supplementary Course book,
Erollu, H., Atatürk İlkeleri ve İnkılap Tarihi, Atatürkçülük.
Atatürk İlkeleri ve İnkılap Tarihi, Atatürkçülük, (YÖK yayını). Karıl, E.Z., Atatürk İlkeleri
ve İnkılap Tarihi, Atatürkçülük
TDL 104 Turkish Language-II (2-0) 2 2
This course aims at communication, language and linguistics, language and thought relations;
relationship between language and culture, cultural varieties, civilization; main language,
context, language and word, symbol-image; language in the world, birth of the languages, types,
classification, place of the Turkish languages among the world languages; development of
Turkish language; current status and spreading areas of the Turkish language; language
information and parts, sound and shape information; sentence information; word types; writing
rules.
Course book,
YÖK. Komisyon, "Türk Dili ve Kompozisyon Bilgileri" YÖK Yayınları.
Ergin, M., "Üniversiteler için Türk Dili", Bayrak Yayınları, İstanbul,1988.
Supplementary Course book,
Gencan, T.N., "Dilbilgisi", Türk Dil Kurumu, İstanbul, 1971.
Ateş, K., "Türk Dili", İmge Yayınları, ISBN: 9755335629, İstanbul,2007
YDL 106 Foreign Language-II (2+0) 2 2
Past Simple of The Verb “To Be”’, Regular and Irregular Verbs, Time Expressions and
Question Words, A Lot of, (a) Little, (a) Few, Comparative and Superlative Forms of
Adjectives, Adverbs and Adjectives, Past Continuous Tense (Past Progressive), Future “Going
to”, Future “Will”.
Course book,
Headway Intermediate, Jonh&Liz Soares, Oxford Univ. Pers, 1987.
Headway Upper Intermediate, John&Liz Soares, Oxford Univ. Pers, 1987
2. SEMESTER NON-TECHNICAL ELECTIVE COURSES
EEM 110 Engineering Ethics and Personal Development (2+0)2 4
This course aims at ethical concepts, engineering ethics, human and its individual
characteristics in engineering ethics in the world and Turkey, communication and persuasion
skills, oratory, speed-reading, time management, stress management.
Course book,
Stephen R. Covey, Living the 7 Habits: The Courage to Change
EEM 112 Photography (2+0)2 4
This course aims at the giving basic information about the history and technique of
photography, the giving practical applications about using of SLR machine, using of
photograph machine, framing, developing of framing ability, teaching of using light.
Course book,
Fotoğraf ve Sinemanın Toplumsal Tarihi Dost Yayıncılık, Levent Kılıç Ankara, 2008
3. SEMESTER
EEM 201 Circuit Theory-I (4+0) 4 4
Resistor, operating principle of inductor and capacitance. Current and voltage. Fundamental
laws. DC circuits. Current and voltage sources. Dependent sources. Mesh current method,
Thevenin, Norton, Millman and Superposition theorems. Steady state and transient analysis of
RL, LC, and RLC circuits. Circuit Theories, DC circuit solution techniques, 1. and 2. Order
circuits. Computer aided circuit analysis applications, error detection and corrections.
Course book:
U. Arifoğlu, Elektrik-Elektronik Mühendisliğinin Temelleri-Doğru Akım Devreleri-Cilt-I,
Alfa Yayınları, 2008.
J. David Irwin, R. Mark Nelms, Basic Engineering Circuit Analysis, 11th Edition,Wiley
Supplementary course book:
D.E. Johnson, J.R. Johnson, J.L. Hilburn, and P.D. Scott, Electric Circuit Analysis, third
edition, Prentice Hall, 1997.
EEM 203 Electronics-I (4+0) 4 4
Crystal structure in solids and energy bands. Conductivity. PN junction diode types. BJT, FET,
MOSFET; CMOS; UJT. 4 layer (p-n-p-n) bi and unipolar circuits. Negative conductivity
microwave equipment. Laser types. Introduction to integrated circuit technology.
Semiconductor diode types. Junction diode characteristic and diode circuits. Rectifiers, clippers
and clampers. DC power supplies. Transistor types (BJT, FET, MOSFET) and their
characteristics. Biasing of Transistors and thermal stability. Models of transistors. Analysis of
transistor amplifier in small signal, low frequency. MOSFET, types and operating
characteristics, multi-layer amplifiers, stability and feedback. LS amplifiers, gain calculations.
Differential amplifiers, operational amplifier, feedback and stability techniques. Oscillators.
Course book:
Türköz, Mehmet Sait, Elektronik, Birsen Yayınevi. L. Nashelsky and R. Boylestad,
Electronics Devices and Circuit Theory, Prentice-Hall.
Supplementary course book:
Hazen, M, Exploring Electronic Devices, Saunders College Publ.
EEM 205 Electromagnetic Field Theory (4+0) 4 4
Vector Calculus, Static Electromagnetic Fields, Coulomb and Gauss Laws, Poisson and
Laplace Equalities, Electrostatic Energy, Solution of Static Boundary Value Problems, Stable
current, Ohm and Joule Laws, Ampere’s Force Law, Biot-Savart Law, Electromagnetic Energy
and Forces, Electromotor Force and Potential.
Course book:
Karabacak,M.,"Elektromanyetik Alan Teorisi Ders Notu",SAÜ Teknoloji Fak.,2013.
Supplementary course book:
F.T. Ulaby, Fundamentals of Applied Electromagnetics, 5th edition, Pearson, 2007
Cerezci, S.S. Seker, Mühendislik Elektromagnetiğinin Temelleri, Saray Bilimsel Yayıncılık,
1996
EEM 207 Computer Aided Analysis (2+2) 3 4
Introduction of MATLAB Software, File and file management in MATLAB. Series and Matrix
Operations, Complex Numbers, Logical Operators and Control sequence commands, M-
functions, Curve fitting and intermediate value calculation, Numerical integration and
derivative, Numerical solution of differential equations, Fourier and FFT, two and three
dimension graphics. Introduction to Simulink, Introduction Simulink Blocks and specifications.
Creating Simulink model and simulation of a system.
Course book:
Uğur Arifoğlu, MATLAB, Simulink ve Mühendislik Uygulamaları, Alfa Yayınları
Hanselman D., Littlefield B, Mastering MATLAB, Prentice Hall.
Supplementary course book:
Biran, A. and Breiner, M. , Addison Wesley, MATLAB for Engineers,
EEM 209 Circuit Theory Laboratory (0+2) 1 2
Laboratory Application of the topics covered in Circuit Theory Course will be done.
EEM 211 Differential Equations (4+0) 4 5
Differential equations and solutions, nonlinear, high order, constant coefficient homogen and
variable coefficient differential equation that can be reduced to constant coefficient equation,
series solution of high order variable coefficient differential equations, series solutions near an
ordinary point, series solution around a regular singular point, Frobenius Method, Laplace
Transform.
Course book:
Çengel, Y. A. ve Palm, W. J. (Türkçesi: Tahsin Engin), 2012, Mühendisler ve Fen
Bilimciler İçin Diferansiyel Denklemler, Güven Kitabevi, İzmir.
Türker, E. S. ve Başarır, M., 2003, Çözümlü Problemlerle Diferansiyel Denklemler,
Değişim Kitabevi, Sakarya
Supplementary course book:
Bronson, R.,1993, (Türkçesi: Hilmi Hacısalihoğlu), Diferansiyel Denklemler, Schaum´s
Outlines, Nobel Kitabevi, Ankara.
Edwards, C. H.ve Penney, D. E., (Türkçesi: Ömer Akın) 2008, Diferansiyel Denklemler ve
Sınır Değer Problemleri, Palme Yayıncılık.
EEM213 Entrepreneurship (2+0) 2 5
Introduction, Entrepreneurship, Notion of Entrepreneurship, Importance and Classifications,
Problems on Entrepreneurship researches, Entrepreneurial Process Interaction Between
Environment, Entrepreneur as a person and characteristics, Business Establishment Process,
Establishment of a new Business and Buying a Business, Analysis and Evaluation of
Opportunities. Business Models and Economic Factors, Business and Marketing Plan,
Financial Planning in Business, Entrepreneurship and investment models, Marketing Sector and
Entrepreneurship, Economic Use of Resources in Entrepreneurship, Innovation and
Technology in Entrepreneurship, Institutional Entrepreneurship, Case Studies.
Course book:
Arıkan, Semra (2004), Girişimcilik, Siyasal kitabevi, Ankara.
Yelkikalan, N. (Edt.) (2013), Girişimcilik, Beta Yayınevi, İstanbul.
3. SEMESTER NON-TECHNICAL ELECTIVE COURSES
EEM 215 Social Gender Equality (2+0) 2 5
What is a Social Gender? Different approaches to social Gender Inequalities: Liberal
Approaches, Marxist Approach, and Postmodern Approach Feminist approaches: Equalist
Feminism, Socialist Feminism, Radical Feminism, Perspective of Social Gender Inequalities in
the World and Turkey: social Gender Inequalities in Production, social Gender Inequalities in
Education, Social Gender Inequalities in Family, Social Gender Inequalities in Politics, Policy
on Social Gender Inequality in the World and Turkey: Equality Policies in working life,
Equality Policies in Education and Family, Equality Policies in Politics, Evaluation.
Course book:
J. Donovan, Feminist Teori, İletişim Yayınları, İstanbul, 1999.
EEM 217 Quality System Management Training (2+0)2 5
Competition and quality concepts, historical development of quality and quality gurus, Total
Quality Management Philosophy and Principles, Quality culture in organizations and quality
responsibilities in activities, continuous improvement (Kaizen), cost of quality, Suppliers in
Total Quality Management, EFQM Excellence Model, Quality Management Systems, ISO
9000, ISO 14000. Understanding total quality management and to make the topics related with
quality management systems understand, to make someone have equipment for applying total
quality management and building quality management system in a workplace.
Course book:
İ. Kavrakoğlu, “Toplam Kalite Yönetimi”, Kalder Yayını, 1996.
4. SEMESTER
EEM 202 Circuit Theory-II (4+0) 4 5
Sinusoidal current, voltage and phasor diagrams, sinusoidal steady state analysis techniques,
Power in AC, three-phase systems, mutual inductance and transformer. Resonance. Laplace
transformation and its application to circuits, transfer functions, frequency response of circuits,
Fourier methods. Four-ended circuits and their input-output impedances, attenuators, filters and
their variants. Analysis of state variables.
Course book:
Abdullah Ferikoğlu, Devre Analizi I-II, Değişim Yayınları, Adapazarı, 2003.
J. David Irwin, R. Mark Nelms, Basic Engineering Circuit Analysis, 11th Edition,Wiley.
Supplementary course book:
D.E. Johnson, J.R. Johnson, J.L. Hilburn, and P.D. Scott, Electric Circuit Analysis, third
edition, Prentice Hall, 1997.
J.W. Nilsson, S.A. Riedel, ´Electric Circuits´, Prentice Hall.
EEM 204 Electronics-II (4+0) 4 5
Basic concepts about amplifiers. Transistor amplifiers; polarization and thermal stability.
Common-emitter circuit. Emitter output circuit. Common base circuit. Differential amplifier.
Multi-level amplifiers. Operational amplifier constructions and models; low frequency power
amplifiers. Digital processing blocks; bipolar transistor gates, MOS transistor gates. DC supply
circuits. Feedback principles. Oscillators. At high frequencies, BJT and FET. Multilayer
amplifiers. Bode drawings. DA, RC and transformer connected amplifiers. Power amplifiers.
Difference receiver amplifiers. Operational amplifiers. Feedback amplifiers and oscillators.
Design of BJT and Op-Amp regulated power supplies. Noise in amplifiers.
Course book:
Türköz, Mehmet Sait, Elektronik, Birsen Yayınevi.
Abdullah Ferikoğlu, İhsan Pehlivan, Matlab® ve OrCAD-PSpice® Simülasyonlarıyla
Çözümlü Devre ve Sistem Analizi Problemleri, Değişim Yayınları, 2010.
Supplementary course book:
L. Nashelsky and R. Boylestad, Electronics Devices and Circuit Theory, Prentice-Hall.
EEM 206 Digital Electronics (4+0) 4 5
Binary Systems, Codes, Boolean Algebra and Logical Gates, Simplification of Boolean
Functions, Combinational Logic, Sequential Logic, Counter. Logic concepts, logical families.
All circuits in digital electronics. Combination circuit design at SSI and MSI level. Code
converters, comparison circuits, MUX, DEMUX and PLA circuits. Sequential digital design.
Binary stable, monostable and unstable elements. Timers, counters, registers and memory
elements. Interface elements, DAC and ADC. Integrated combinational circuits: collectors,
multiplexers, data selectors.
Course book:
Ekiz Hüseyin; Mantık Devreleri, Değişim Yayınları, 2008
H. S. Selek, Mantık Devreleri, Seçkin Yayıncılık, 2013
Supplementary course book:
Mano Morris, Digital Design, Prentice Hall
EEM 208 Electromechanical Energy Conversion (3+0) 3 5
Introduction, Introduction to Circular Motion, Newton's Law, Motor, Generator and
Transformer Definitions, Magnetic Field, Magnetic Flux and Magnetic Flux Density Concepts,
Ferromagnetic Materials, Magnetic Field Intensity, Ampere Law, Hysteresis Cycle and Losses,
Eddy Current and Losses, Magnetic Reluctance concept, Magnetic equivalent circuits.
Transformers, Magnetomotive force and rotating field definitions. Basic principles of direct
current, asynchronous and synchronous machines.
Course book:
Stephen J. Chapman, "Electric Machinery Fundamentals", Fourth Edition McGraw-Hill,
Inc., 2005.
Turan Gönen, Electrical Machines, Power International Press, 1998.
Supplementary course book:
Sarma, Electric Machines, 2nd Ed., West Publishing, 1994.
EEM 210 Digital Electronics Laboratory (0+2) 1 2
The laboratory applications of the subjects covered in Digital Electronics course will be done.
EEM 212 Electronics Laboratory (0+2) 1 2
Lab-application of the subjects covered in Electronics-I and Electronics-II courses will be done.
EEM 214 Probability and Statistics (3+0) 3 4
Basic concepts about probability and statistics. Random variables and special functions.
Distribution and density functions. Multivariate distributions and densities. Independent
random variables. Application of correlation statistics to engineering systems.
Course book:
S. M. Ross, Olasılık ve İstatiğe Giriş, Nobel Akademik Yayıncılık
Supplementary course book:
R. D. Yates, D. J. Goodman, Introduction to Probability and Stochastic Processes, 2nd
edition
4. SEMESTER NON-TECHNICAL OPTIONAL COURSES
EEM 216 Table Tennis (2+0) 2 2
Materials used in table tennis, technical information, teaching, training methods.
Course book:
E. Güven, Masa tenisi, Teknik, Taktik Kondisyon,1987.
EEM 218 History of Science (2+0) 2 2
Definition of science. Scientific information. Introduction to the history of science. Science in
the first civilizations. Science in the ancient Greek world (antiquity). Science in the ancient
Greek world (Hellenistic age). Science in the Middle Ages (Islamic world and European
comparisons). Informal contributions of Turkish in the middle ages. The periods and causes of
scientific progress and pause in the Islamic world. Science in the Renaissance, awakening of
the western world. Science in the 17th and 18th centuries. Science in the 19th and 20th
centuries. Science in our country during the Republican era. A scrutinizing of scientific
developments and scientific indicators in our country, a comparison with the world and a
general assessment of the future.
Course book:
Colin A.Ronan, Bilim Tarihi Dünya Kültürlerinde Bilimin Tarihi ve Gelişmesi, TÜBİTAK
Yayınları, Akademik Dizi I, Ankara, 2003.
Cemal Yıldırım, Bilim Tarihi, 1997, Remzi Kitabevi
Supplementary course book:
Prof. Dr. Şafak Ural, Bilim Tarihi, III C., İstanbul, 1995.
Aleksandre Koyre, Yeniçağ Biliminin Doğuşu, Ankara, 1995.
5.SEMESTER
EEM 301 Electrical Machines-I (3 + 0) 3 3
Magnetic circuits. One-phase, three-phase and auto-transformers. Connection types of
transformers. Measurement transformers. Electromechanical energy conversion principles and
their dynamic equations. DC machines, steady state analysis and performance, DC machine
dynamics and control, rectifier circuit principles, semi-conductor control systems.
Course book:
Stephan Chapman, Electric Machinery Fundamentals, McGraw-Hill, 2004
Supplementary course book:
A. E. Fitzgerald, Charles Kingsley Jr, Stephen Umans, Electric Machinery, McGraw-Hill,
1992
EEM 303 Signals and Systems (3 + 0) 3 3
Introduction to signals and systems. Linear time-invariant systems. Fourier series
representations of periodic signals. Continuous time fourier transformation. Discrete time
fourier transformation. Sampling theory. Modulation theory. Laplace transformations.
Introduction to Z transform.
Course book:
H.P. Hsu (Çev. Veysel Silindir/ Erkan Afacan/ M. Timur Aydemir/ Hasan Dağ )
Sinyaller ve Sistemler / Schaum´s Outlines, Nobel Yayın Dağıtım, İstanbul, 2002
Signals and systems, A.V. Oppenheim, A. S. Willsky, 1998
Supplementary course book:
M.H. Hayes (Çev. Erhan Akın ) Sayısal İşaret İşleme / Schaum´s Outlines, Nobel Yayın
Dağıtım, İstanbul, 2000
EEM 305 Control Systems (4 + 0) 4 3
Basic concepts. Mathematical models of physical systems. Block diagrams, signal flow
diagrams and transfer functions. Analysis of control systems in time domain, frequency domain
and discrete time domain. Stability concepts; root locus, Bode, Routh table, Nyquist diagrams
and Liapunov methods. Compensators.
Course book:
Norman S. Nise, Control Systems Engineering, Second Edition, The Benjamin / Cummings
Publishing Company, 1995.
Richard C. Dorf, and Robert H. Bishop, Modern Control Systems, Eighth Edition, Addison
Wesley Longman, 1998.
Supplementary course book:
Katsuhiko Ogata, Modern Control Engineering, Third Edition, Prentice Hall, 1997.
Benjamin C. Kuo, Otomatik Kontrol Sistemleri, Çeviren ve Uyarlayan Atilla Bir, Literatür
Yayıncılık, 1999.
M. Kemal Sarıoğlu, Otomatik Kontrol I-II, Birsen Yayınevi - İstanbul, 1999.
İbrahim Yüksel, Otomatik Kontrol Sistem Dinamiği ve Denetim Sistemleri, Uludağ
Üniversitesi - Bursa, 1997.
EEM 307 Introduction to Communication (3 + 0) 3 3
Basic concepts; communication theorem; basic band and transmission band concepts;
modulation and demodulation methods; types and techniques of multiplexing; analogue
communication systems; Introduction to digital communication systems.
Course book:
J. G. Proakis, M. Salehi, Communication Systems Engineering, third edition, Prentice Hall,
2005.
S. Haykin, Communication Systems, fourth edition, Wiley, 2000.
Supplementary course book:
J. D. Gibson, Principles of Digital and Analog Communications, Macmillan, 1993.
EEM 309 Signal Processing and Communications Laboratory (0 + 2) 1 2
Laboratory applications of the topics seen in Signal Processing and Communication course will
be done.
EEM 311 Control Laboratory (0 + 2) 1 2
Laboratory applications of the topics seen in Control Systems course will be done.
5. SEMESTER TECHNICAL ELECTIVE COURSES
EEM 315 Antennas and Microwave Technique (3 + 0) 3 5
Antenna parameters. Linear antennas. Radiation diagrams and impedance of antennas. Receiver
and transmitting antennas. Antenna arrays. Reflector antennas. Introduction to ground waves
and propagation. Introduction to radar systems.
Course book:
J. G. Proakis, M. Salehi, Coomunication Systems Engineering, third edition, Prentice Hall,
2005.
S. Haykin, Coomunication Systems, fourth edition, Wiley, 2000.
Supplementary course book:
J. D. Gibson, Principles of Digital and Analog Communications, Macmillan, 1993.
EEM 317 Industrial Electronics (3 + 0) 3 5
Linear and nonlinear applications of operational amplifiers: Current sources, negative
impedance transducers, rectifiers, AC-DC converters, analog multiplication-division,
squareroot extraction circuits, integral and derivative circuits, comparators, Schmitt triggering
circuits, oscillator applications, OTA applications: analog impulse circuit, multiplexer, active
filters, OTA-C oscillators. Instrumentation amplifier. Phase locked loop applications. Power
Supplies: Constant and adjustable voltage regulator power supply design with all circuits,
switched power supplies (DC-DC converters). Computer simulation of electronic systems.
Course book:
T.E. Kissel, Industrial Electronics, Prentice Hall, 2003.
C.D. Simpson, Industrial Electonics, Prentice Hall, 1996.
Supplementary course book:
N. Mohan, T.M. Undeland, W.P. Robbins, Power Electronics, John Wiley and Sons. Inc.,
New York, 1995.
EEM 319 Energy Transmission and Distribution-I (3 + 0) 3 5
Distribution systems, determination of electricity consumption requirements, load
characteristics. Elements used in distribution systems, selection criteria of distribution
conductors, isolators, safety margin, underground designs of energy distribution lines.
Switchboards. Measuring methods in energy transmission lines. Electric pole and conductors
used in transmission lines, transformers transformer centers and protection methods of
switching elements.
Course book:
E. Turgut, K. Selçuk, Elektrik Enerjisinin Üretimi, İletimi ve Dağıtımı, Detay Yayıncılık,
2009
Supplementary course book:
İ. Tosun, Enerji İletimi ve Dağıtımı, Birsen Yayınevi, 2007
EEM 321 Digital Design (3+0) 3 5
To understand the use of synchronous sequential / sequential circuits by recognizing the basic
concepts of multivibrators and Flip Flops. To explain counters and counter types and counter
designs. To teach recorders and recorder types, to increase memory capacity by elaborating /
grouping memory, to explain programmable logic elements.
Course book:
Ekiz Hüseyin; Mantık Devreleri, Ders Kitabı, Değişim Yayınları
Supplementary course book:
Mano Morris, Digital Design, Prentice Hall
EEM 323 Business English-I (3+0) 3 5
Technical vocabulary used in various fields of electrical and electronics engineering,
Grammatical structures used in scientific and technical writing, Translation techniques and their
applications into scientific texts, How to write a technical report, How to prepare and make a
presentation on a technical subject.
Course book:
Erik H. Glendinning, English in Focus: English in Electrical Engineering and Electronics,
Oxford University Press, 1992
EEM 325 Microcontrollers (3 + 0) 3 5
Basic features of microcontroller, microcontroller architectures, microcontroller embedded
systems and their structural features, PIC family microcontrollers, program and data memories,
memory map, command structure and operation, port usage features for input / output, key
reading and display techniques, internal peripheral units , hardware interface creation.
5. SEMESTER NON-TECHNICAL ELECTIVE COURSES
EEM 327 Project Preparation and Management Education (2 + 0) 2 2
The main aims of project preparation, Reasons for preparing a project, Why do we prepare
projects, Realizing that problem situations in various fields can be projected, Relationship
between science, research and project, The necessity of researching in reaching information, It
gives examples of situations around which it is uncomfortable. Determines the subject of the
project related to the subject of the disturbance. Establishes the relationship between project
preparation steps and project writing steps. It organized data obtained in accordance with the
writing project steps. It makes the project ready for presentation. It offers the project. What to
do in order to follow the presented project is determined.
Course book:
Proje Döngüsü Yönetimi: Proje Teklif Yazma, İzleme ve Değerlendirme, Nurhan Yentürk
ve Yiğit
EEM 329 Occupational Safety (2 + 0) 2 2
In general, accident, statistical analysis of occupational accidents, occupational diseases,
reasons of occupational accidents, importance and effect area of occupational diseases,
importance of human factor in occupational diseases and occupational accidents, occupational
safety, fire and protection, first aid, worker health and occupational safety legislation as
business security. Basic Ethical Theories, Ethical-Moral Relations, Ethical-Engineering
Relation, Ethical View in Historical Development Process, Ethical Theory; importance
principle, internalization-consistency principle, usefulness principle, Value ethics, Business
and Professional ethics, engineering ethics and its definition, tmmob vocational behavior
principles.
Course book:
Çevre Ve İşçi Sağlığı İş Güvenliği Ders Notları Türk-İş Yayınları
Supplementary course book:
İş Güvenliği Nahit Tekin
Schinzinger, R., Martin, W. M.Introduction to Engineering Ethics. McGraw-Hill,USA,
2000
Aksakoğlu, İstanbul Bilgi Üniversitesi Yayınları 146, STK Çalışlamaları, Eğitim Kitapları
EEM 331 Basketball (2 + 0) 2 2
Rules, field and material knowledge; warming and streching. Basketball techniques, individual
offense and defensive features; team offense and defense.
Course book:
Alpullu, Her Yönüyle Basketbol, Beta Yayıncılık.
6. SEMESTER
EEM 302 Electrical Machines-II (3 + 0) 3 3
Rotating magnetic field and three phase system of windings. MMK curves rotating at AC
machines, electric machines performance and their yield. Asynchronous machines, equivalent
circuits and speed control. Synchronous machines, equivalent circuits and state characteristics.
Parallel coupling and load transfers. Synchronization. Low powerful AA electric machines.
Course book:
Stephan Chapman, Electric Machinery Fundamentals, McGraw-Hill, 2004
Supplementary Course book:
A. E. Fitzgerald, Charles Kingsley Jr, Stephen Umans, Electric Machinery, McGraw-Hill,
1992
EEM 304 Microprocessors (3 + 0) 3 3
Microprocessor based systems. Introduction to 80x86 microprocessor family. Software
architecture. Address modes. Data Transfer commands. Arithmetic, logic, bit manipulation.
Program transfer and processor control commands. Interrupt types for software and hardware.
Introduction to programming. Applications for programming. Hardware architecture: Basic
information about 80x88 hardware. Memory system design. I / O system design. A working
8088 system design.
Course book:
N. Topaloğlu, x86 Tabanlı Mikroişlemci Mimarisi ve Assembly Dili, Seçkin Yayıncılık,
2008
Supplementary Course book:
M. Kaya Yazgan, Mikroişlemciler, Nobel Akademi, 2015
EEM 306 Power Electronics (3 + 0) 3 3
Mechanism, modeling and behavior of propulsion systems,moment characteristics of motors
and loads, stability, working in electric machines and feeding with shredders,modeling and
control principles of asynchronous motors, starter and speed control with AC shredder and
intermediate circuit and AC converters,design of propulsion systems, selection of motor and
control equipment. Power converter definitions and classification. Power semiconductors and
their properties. Rectifying elements, control rectifier elements SCR with TRIAC control
circuits and characteristics, stepper motor drive and control circuits, use in frequency changers
and speed control. DC pulsers, inverters, PWM inverters, resonant pulse converters, static
switching power supplies, DC drives, AC drives, protection devices and circuits.
Course book:
Bodur,H.,“Güç Elektroniği”,BİRSEN Yayınevi,2010.
Shepherd,W., Zhang,L.,"Power Converter Circuits",Marcel Dekker,2004.
Supplementary Course book:
Dewan, S.B., Slemon,G.R., Straughen,A.,"Dewan "Power Semiconductor Drives",Wiley,
1984.
Mohan,N., Undeland,T.M., Robbins, W.P.,"Power Electronics Converter Applications and
Design",Wiley, 2003.
EEM 308 Computer Aided Drawing (2 + 2) 3 3
Standard 2-D drawings, Engineering Drawings and CAD software, Measurement in 2-
dimensional drawings, Assembly drawings, 2-dimensional techical drawings.
Course book:
İ. Z. Şen ve N. Özçilingir, “Teknik Resim”, Deha Yayıncılık, 2010.
EEM 312 Electrical Machines Laboratory (0 + 2) 1 3
Laboratory applications will be done for the topics seen in Electrical Machinery course.
EEM 314 Microprocessors Laboratory (0 + 2) 1 3
Laboratory applications will be done for the topics seen in Microprocessors course.
6. SEMESTER TECHNICAL ELECTIVE COURSES
EEM 316 Digital Communications (3 + 0) 3 5
Sampling Theorem, Pulse Amplitude Modulation (PAM) and Time Division Multiplexing
(TDM), PAM / TDM Systems, Pulse Time Modulation and Variations (PPM, PWM), Pulse
Code Modulation (PCM), Quantization, Encoding, PCM Signals and Gaussian Noise , Delta
Modulation (DM) and Differential PCM, Baseband Information Transmission, Line Coding,
ISI, Bit Error Rates and Bit Error Probability in Baseband Information Transmission, Optimum
Receiver Design for Additive White Gaussian Noise (AWGN) Digital modulating systems,
Multiplexing and multiple access in digital communication, Digital wireless communication
systems.
Course book:
J. G. Proakis, M. Salehi, Communication Systems Engineering, third edition, Prentice Hall,
2005.
S. Haykin, Communication Systems, fourth edition, Wiley, 2000.
Supplementary Course book:
C. R. Johnson Jr., W. A. Sethares, Telecommunication Breakdown, Prentice Hall, 2004.
J. D. Gibson, Principles of Digital and Analog Communications, Macmillan, 1993.
EEM 318 Electrical and Electronics Measurement (3 + 0) 3 5
Basic principles and characteristics of the measurement (sensitivity, accuracy, linearity, effect,
response time, etc.). Design and calibration terms, measurement errors and error sources.
Measuring methods and measuring of circuit elements, analogue measuring instruments,
moving measuring instruments, changing the measuring limits and measuring instrument
accuracy. Alternating current bridges; measurement of inductance, capacity and loss factor, Q-
meter. Counters and digital measuring, analog-to-digital converters and converters; Flash,
single and double slope voltage-frequency converters. Power and energy measurement,
triggering circuits and measurement. Instrumentation amplifiers and related concepts.
Course book:
Bodur, Aydın, vd.; Enstrümantasyon ve Ölçme, İnfogate, 2001.
Supplementary Course book:
Pastacı, Halit; Elektrik ve Elektronik Ölçmeleri, Metinler Matbaacılık, 1988.
Bolton, W.; Electrical and Electronic Measurement and Testing, Longman Scientific and
Technical, 1992.
EEM 320 Energy Transmission and Distribution-II (3 + 0) 3 5
Energy distribution criteria, distribution systems, load characteristics, distribution
transformations, regulators, substations and protection devices. LC line model. transmission
line equations, transmission line losses, general parameters of transmission lines. End of line
and mappings. Periodically loaded lines and models. Interconnected lines and models.
Protection principles. Current and voltage transformers. Overcurrent, differential and
impedance protection systems. Transformer, generator and line protection. Surge Arrester.
Grounding and insulation.
Course book:
E. Turgut, K. Selçuk, Elektrik Enerjisinin Üretimi, İletimi ve Dağıtımı, Detay Yayıncılık,
2009
Supplementary Course book:
İ. Tosun, Enerji İletimi ve Dağıtımı, Birsen Yayınevi, 2007
EEM 322 Industrial Automation Systems (3 + 0) 3 5
Control circuit elements, contactors, thermal elements, switches, relays, symbols,
characteristics and working principles of thermostats. Engine control circuits; starting,
stopping, braking, changing direction. Diagrams and connections of the circuits of the speed
control circuits. Properties of semi-conductor control circuit elements, Limit-switch switches,
position detection. 1-phase and 3-phase asynchronous motor control circuits and its
applications. Electrical circuit connections of Programmable Logic Controllers (PLC) and
additional modules. Time relays. Counters. Move, copy, and shift commands at memory
addresses. Analogue and digital conversions and its applications. Sub-loop, real-time clock.
Interrupts, high-speed counter. Industrial communication networks, touch-sensitive panel
applications.
Course book:
Electrical Command Circuits and PLC, Prof. İsmail Coşkun, Yrd. Doç. Dr. Mahir Dursun,
Dr. Ali Saygın
EEM 324 Business English-II (3 + 0) 3 5
Technical terms in Electrical and Electronics Engineering, Circuit Theory, Electromagnetic
Fields, Information Technology, Logic Circuits and Design, Signals and Systems, Electronics,
Communication, Electric Machines, Energy Systems, Translation Techniques and application
to professional texts, Grammar and sentence structures used in professional books and articles,
Writing various technical reports, technical presentations.
Course book:
Erik H. Glendinning, English in Focus: English in Electrical Engineering and Electronics,
Oxford University Press, 1992
EEM 326 Filter Design (3 + 0) 3 5
Time-frequency response, Poles and zeros, Analogue LP filter, Analogue HF filter, Band stop
filter, Element selection for analogue filters, Digital FIR filter design, Digital IIR filter design,
Filter applications
6. SEMESTER NON-TECHNICAL ELECTIVE COURSES
EEM 328 Management and Organization (2 + 0) 2 2
System theory and organizations, objectives, productivity measures and requirements in public
and private sectors, basic structure and variability of an organization, basic building blocks, life
cycle of an organization and change management
Course book:
Amrine, H.T., Ritchey, J.A., Hulley, O.S., “Manufacturing Organization and Management”
Prentice-Hall, 1992.
EEM 330 Economics (2 + 0) 2 2
Households, firm preferences, the economy as a whole, total economic behavior.
Course book:
O. Okka, “Mühendislik Ekonomisi”, Nobel Yayın Dağıtım, 2011.
EEM 332 Ceramic (2 + 0) 2 2
Muds, basic ceramic production techniques, drying, retouching, loading to oven, glazing, mold
techniques
Course book:
A. Arcasoy, “Seramik Teknolojisi”, Marmara Üniversitesi Güzel Sanatlar Fakültesi
Seramik Anasat Dalı Yayınları No:1
7.SEMESTER
EEM 401 EE Engineering Design (2 + 2) 3 4
Students conduct a design supervised by their advisors to show the information they have
learned throughout their studies.
7. SEMESTER TECHNICAL ELECTIVE COURSES
EEM 405 Lighting and Interior Installation Project (3 + 0) 3 4
1/50 scale electric interior installation project. Electric interior installation. Electric Interior
Facilities Regulation. Key and socket types. Electrical interior installation materials. High
current and weak current single line and open schemes. High current column scheme. Table
loading ruler. Voltage drop account. Fuse and section selection.
Course book:
M. Özkaya, “Aydınlatma Tekniği”, Birsen Yayınevi, 2000.
Ali Doğru, Mahmut Nacar, Elektrik Tesisat Planları Sözleşme Keşif ve Planlama
(Elektrik Projeleri), 2014
EEM 407 Power System Analysis-I (3 + 0) 3 4
Introduction to power systems. Resistance, inductance and capacitance in transmission lines.
Electrical characteristics of transformers and generators. Short, medium and long lines. Per
Unit systems. Modeling of power systems, symmetrical short circuit analysis.
Course book:
Ş. Ağalar, Güç Sistemleri Analizi, Anadolu Üniversitesi Yayınları
Supplementary course book:
U. Arifoğlu, Güç Sistemlerinin Bilgisayar Destekli Analizi, Alfa Yayıncılık
EEM 409 Protection in Power Systems (3 + 0) 3 4
The basic principles of protection. Protection with insurance in LV and HV systems. Relays
and properties. Protection with overcurrent relay, impedance relay and differential relay.
Generator, line, transformer and motor protection. Relay coordination. Overvoltage protection
devices. Surge arresters, protection lines, jump ranges.
Course book:
Orta Gerilim Elektrik Tesislerinde Koruma ve Kontrol –TEDAŞ.
Supplementary course book:
Power System Protection – Volume 1-2-3, The Institution of Electrical Engineering,
London .
EEM 411 Digital Signal Processing (3 + 0) 3 4
Discrete-time domain and frequency domain representations of signals and systems. Sampling
and repetition. DFT, FFT, z - transform, filter design techniques. Finite word length effects. 2-
dimensional filtering. Digital Signal Processing applications.
Course book:
John G. Prokis and Dimitris G. Manolakis, “Digital Signal Processing : Principle,
Algorithms and Applications” Prentice Hall Inc., Englewood Cliffs, NJ (USA), 3rd Ed., 1996.
Supplementary course book:
K. Mitra, “Digital Signal Processing : A Computer-Based Approach” Mc Graw Hill Co.
Inc., NY (USA), 1998
EEM 413 Special Electrical Machines (3 + 0) 3 4
One-phase asynchronous Motors and structure. Repulsion motors and operation. Examination
of hysteresis motors. Structure of step motors. Universal Motor and control. Speed control in
universal motors. Brushless DC motors. Permanent magnet synchronous motors. Features and
applications of permanent magnet synchronous motors. Reluctance motors and structure.
Switched reluctance motors.
Course book:
G. Bal, Özel Elektrik Makinaları Seçkin Yayıncılık, 2004, Ankara
Supplementary course book:
Altunsaçlı, Elektrik Makineleri-III, Color Ofset, İskenderun
EEM 415 Computer Aided Circuit Design (3 + 0) 3 4
Introduction of Simulation Program, Simulation of Basic Circuits, Simulation of Analog
Circuits, Simulation of Digital Circuits, Introduction of Print Circuit Program, Circuit Drawing
in Program Environment, Creating Print Circuit Schemes.
Course book:
H.Şahin, Proteus Design Suite 8, Altaş Yayınları,2013
EEM 417 Wireless Communications (3 + 0) 3 4
Introduction to wireless communication systems and standards, radio propagation effects,
coverage area and statistical channel modeling, time varying channels, fading effects, various
bandpass modulation types and receiver / receiver systems, channel capacity, spread spectrum
communication, diversity and combining techniques in cellular systems.
Course book:
Haykin, S. and Moher, M., Modern Wireless Communications, Prentice Hall, 2005.
Supplementary course book:
Goldsmith, A., Wireless Communications, Cambridge Univ. Press, 2005.
EEM 419 Control Systems Design (3+0) 3 4
Demonstration of systems with state variables, demonstration with integrators or regulators.
Demonstration of transfer function and other forms of linear time invariant systems.
Controllability and simple controller design. Observability and simple collector design. PID
control and determination of the best gain values. State space drawings. Quadratic scalar
functions. Lyapunov stability theory. Introduction to optimal control. Simple optimal control
applications. Control applications with PIC. PIC simulations.
Course book:
B. Kuo, “Otomatik Kontrol Sistemleri”, Literatür Yayıncılık, 2009.
Supplementary Course book:
K. Ogata, “Modern Control Engineering”, Prentice Hall, 2009.
EEM 421 Artificial Neural Networks (3 + 0) 3 4
Neural systems as a source of biological inspiration. Definition and history of Artificial Neural
Networks (YSA). Learning with an instructor and without an instructor. Advanced path
networks: Adaptive linear element. Learning rules: Least square mean learning rule,
backpropagation. Learning without the trainer: ART, Kohonen network, winner takes all,
grouping, vector quantization. Dynamic systems: Dynamic system, Hopfield network, Cellular
artificial neural network. İntensive learning.
Course book:
E. Öztemel, Yapay Sinir Ağları, Papatya Yayıncılık Eğitim, 2006.
Supplementary Course book:
J. M. Zurada,Introduction to Artificial Neural Systems West Publishing Company, St. Paul,
Minnesota, 1992.
EEM 423 Programmable Logic Control (3 + 0) 3 4
The basic technology of PLC, PLC units, PLC interface program, programming with ladder
diagram, using sequential function blocks programs, using operator panel / touch panel,
programming operator panel / touch panel, operating pneumatic circuit with PLC, operating
pneumatic circuit with PLC, operating hydraulic circuit with PLC, doing motor control with
PLC
Course book:
S. Aksoy, Programlanabilir Lojik Denetleyiciler ve Mühendislik Uygulamaları, Değişim
Yayınları, 2011
EEM 425 Satellite Communications (3 + 0) 3 4
History of satellite, types of satellite according to work area. Satellite types according to orbit
types. Satellite communication parameters. Ground-to-satellite connection, satellite transmitter
/ receiver and satellite-to-ground basic satellite communication system. Explanation of the
Satellite Communication System. Explanation of Analog Satellite Transmitter. Explanation of
Satellite Receiver System, Dish Antennas and LNBs. Explanation of Analog Satellite
Receivers. Disclosure of direct broadcast satellite vehicles and their purposes. Satellite Receiver
System Explanation of setup and setting of Dish Antennas. TURKSAT PROJECT. GSM
network, AMPS, NMT, TACS, Mobile 900-1800-1900 Cellular Mobile Phone systems.
Explanation of the cellular system.
Course book:
Uydu ve Hücresel Mobil Haberleşme Sistemleri, 2. baskı., Birsen Yayınevi, 2002.
Supplementary Course book:
Satellite Communication Engineering, New York, USA: Marcel Dek. Incorporated, 2002.
EEM 427 Computer Network Technologies (3 + 0) 3 4
Introduction to computer networks. OSI model. LAN protocols, IEEE 802.2 and Ethernet. Data
link layer, error detection and correction protocols. Network layer and transport layer. Internet,
the structure of the Internet and Internet tools. Network planning, Ethernet and alternatives.
WAN protocols
Course book:
James F. Kurose, Keith W. Ross, Computer Networking 5/E, Addison Wesley, 2010.
Rifat ÇÖLKESEN, Bülent ÖRENCİK, Bilgisayar Haberleşmesi ve Ağ Teknolojileri, Papatya
Yayıncılık, 2008
Supplementary Course book:
Andrew S. Tanenbaum, Computer Networks 4/E, Prentice Hall, 2003.
EEM 429 Robotics (3 + 0) 3 4
Introduction of robot systems; Kinematics of robot joints; Robot dynamics; Independent joint
control, Accelerator dynamics and control, Application of PD, PID type controllers to robot
systems; Examples from MATLAB Robotic Toolbox; Robot-controlled state feedback and
observers; Feedback and feedforward control (calculated moment method); Multivariate
control in robot arms; Inverse dynamic method; Stability problem in robots.
Course book:
Robot Modeling and Control, M. W. Spong, S. Hutchinson, M. Vidyasagar, Wiley, 2005.
Supplementary Course book:
Introduction to Robotics: Mechanics and Control 3th Edt., J.J: Craig, Prentice Hall, 2003.
EEM 431 Renewable Energy Sources (3 + 0) 3 4
Renewable energy sources. Techniques of converting wind and solar energy. Simulation
techniques for optimization of energy resources and energy requirements.
Coursebook:
R.A.Kelly, Energy Supply and Renewable Resources, Prentice Hall, 2010.
Supplementary Course book:
D. Pimentel, Biofuels, Solar and Wind as Renewable Energy Systems Benefits and Risks.
Springer Verlag 2008.
8. SEMESTER
EEM 402 Workplace Training (6 + 6) 9 30
The student will gain work experience by applying what they have learned during engineering
education in a workplace.