- 1 - 8th edition
No. SS2-8113-1110
CV3000 SeriesCompressible Fluid Service
Low-Noise Cage type Control ValvesModel HCN
OVERVIEW
Model HCN Low-Noise Cage type Control Valves have been designed to remarkably reduce acoustic noise in services of compressible fluids such as steam, air, and natural gas. The cage has a large number of small holes and renders an ideal pressure reduction with a combination in two steps of “restriction” and “diffusion and expansion.” The fluid passage has been designed in S-figure shape for smooth flow of fluid with less pressure loss and a stabilizer is provided as a strainer for flow near the cage, thereby permitting a large Cv value.The valve plug is of a pressure-balanced type which allows control of a high differential pressure with a small actuating force. The actuator is a compact but high output diaphragm motor of a multiple spring type structured in a simple mechanism.The model HCN valves, which are compact but of a low noise type and render high dynamic stability, are suitable especially for control of high temperature, high pressure or high differential pressure process lines.
SPECIFICATIONSBody
TypeStraight-through, cast globe valve
Nominal size1½, 2, 2½, 3, 4, 6, 8 inches
Pressure rating• JIS 10K, 16K, 20K, 30K, 40K• ANSI Class 150, 300, 600• JPI Class 150, 300, 600
End connection• Flanged end;
• Welded end; SW (1½, 2 inches)BW (2½ to 8 inches)
Connection type Pressure rating Applicable standard
FFJIS10K JIS B2210-1984ANSI Class 125 ANSI B16.5-1981JPI Class 125 JPI-7S-15-1993
RFJIS10K, 16K, 20K, 30K, 40K JIS B2210-1984ANSI Class 150, 300, 600 ANSI B16.5-1981JPI Class150, 300, 600 JPI-7S-15-1993
RJ, LG ANSI Class 150, 300, 600 ANSI B16.5-1981JPI Class 150, 300, 600 JPI-7S-15-1993
Tongue and groove(groove)Male and female(female)
JIS16K, 20K, 30K, 40K JIS B2202-1984
MaterialFor body/trim material combinations and operating temperature ranges, refer to Table 1.
Bonnet• Plain bonnet (-17 to +230 °C)• Extension bonnet type 1;
(-45 to-17 °C and +230 to +566 °C)• Extension bonnet type 2;
Integral cast type (-100 to -45 °C)Welded type (-196 to -100 °C)
Note) Take care not exceed the operating temperature ranges specified for respective materials.
Gland typeBolted gland
Packing / Grease• Grease not provided
When V shaped PTFE packing or PTFE yarn pack-ing is used.
• Grease providedWhen graphite packing is used.
Note) PTFE: Polytetrafluoroethylene
No. SS2-8113-1110 Azbil Corporation
- 2 -
GasketTypeCombination of serrated type and spiral wound type (integral cage), Serrated type (split cage)
MaterialStainless steel (SUS316), copper, aluminum
TrimValve plugPressure-balanced type
Cage (integral or split cage)Multiple-orifice design
Metal seatLinear (LV)
Note) For cage design (integral cage or split cage), refer to Table 1.
MaterialFor body/trim material combinations and operating temperature ranges, refer to Table 1.
Note) For fluid conditions that require Stellite, refer to Figure 2.
ActuatorTypeSingle acting diaphragm actuator (Type HA or VA5)Spring type piston actuator (Type PSA6R)
ActionDirect or reverse action
DiaphragmType HA: Cloth embedded ethylene propylene rubberType VA: Cloth embedded chloroprene rubber
Spring range20 to 98 kPa {0.2 to 1.0 kgf/cm²}40 to 120 kPa {0.4 to 1.2 kgf/cm²}80 to 240 kPa {0.8 to 2.4 kgf/cm²} (Type HA or VA5)200 to 340 kPa {2.0 to 3.5 kgf/cm²} (Type PSA6)
Supply pressureDiaphragm actuator
Type HA: 120 to 390 kPa {1.2 to 4.0 kgf/cm²}Type VA5: 120 to 270 kPa {1.2 to 2.8 kgf/cm²}
Spring type piston cylinderType PSA6: 390 kPa {4.0 kgf/cm²}
Note) Allowable differential pressure varies depending on spring range and air supply pressure.
Air connectionRc1/4 or 1/4NPT internal thread
Note) With Type VA, Rc1/4 or 1/4NPT adapter is provided on Rc1/2 internal thread (also providing Rc3/8 adapter is possible).
Ambient temperature-30 to 70 °C
Valve actionAir-to-close (Direct action actuator is combined.)Air-to-open (Reverse action actuator is combined.)
Optional accessoriesPositioner*, pressure regulator with filter, hand wheel*, limit switch, solenoid valve, motion transmitter, booster relay, lock-up valve, and others.
Note) 1)For the optional items, refer to the specification sheets and installation drawings of respective accessories.
2)Accessories with the asterisk mark (*) are selected from among the following types depending on the actuators to be combined.
Additional specification (by special order)• Special inspection
Flow characteristics inspection, material inspection (material certificate), non-destructive inspection, steam inspection
• With drain plug• Double gland• Oil-/ water-free treatment• Copper-free treatment• York material SCPH2• Stainless steel (SUS304) atmosphere-exposed nuts and bolts• Special air piping and joint• Sand-/ dust-preventive measure• Saline damage countermeasure• Cold-area use specification• Tropical-area use specification• Vacuum service
Performance
Rated Cv ValueRefer to Table 2.
Flow characteristicsRefer to Figure 1.
Inherent rangeability• 25 : 1 • Optional 50 : 1 for full port size
Allowable differential pressureRefer to Table 7 to Table 12.
Leakage specificationIEC 60534-4:2006 or JIS B 2005-4:2008Class III: Leakage less than 0.1% of maximum valve capacity.
Hysteresis errorWithout positioner: Within 3% F.S.With positioner: Within 1% F.S.
ActuatorPositioner Hand wheel
P/P I/P Top Side
HA2 to 4 HTP AVP/HEP THM SHMVA5 HTP AVP/HEP THM SHM
PSA6 HTP/VPP AVP/HEP - SHM
Azbil Corporation No. SS2-8113-1110
- 3 -
LinearityWithout positioner: Within ±5% F.S. ((Within 9% F.S.))With positioner: Within ±1% F.S. ((Within 2% F.S.))
Note) 1) When positioner is not provided, operating performance may vary depending on type of packings used.
2) Double parenthersized figures are applicable to type PSA6.
[For estimating noise volume, refer to related instru-mentation document No. ID2-8000-1700.]
DimensionsRefer to Figure 4, Table 13 and Table 14.
WeightRefer to Table 15.
Actuator orientationRefer to Figure 5.
FinishBlue (Munsell 10B5/10) or silver, or other specified color
Table 1 Body / trim material combinations and operating temperature ranges (°C)
Body material
Trim material
JIS SCPH2 SCPH21 SCPH61 SCS13A SCS14A
ASTM A216WCB A217WC6 A217C5 A351CF8 A351CF8M
JIS SCS24 and SUS630 -5 to 425 -5 to 425 -5 to 425
JIS SCS14A and SUS316 -5 to 300* -5 to 300* -5 to 300* -196 to 300 -196 to 300
JIS SCS14A Stellite and SUS316 Stellite -5 to 425* -5 to 550* -5 to 566* -196 to 550 -196 to 550
JISSCS14A Atomlloy treatmentSUS316 Atomlloy treatment
-5 to 425* -5 to 500* -5 to 500*
Note) 1) Asterisk marked (*) combinations, split cages are used when fluid temperature exceeds 230 °C or valve size is greater than 3 inches.
2)“ ” shows standard combination of valve body and trim materials.
Table 2 Cv value and travel
Nominal size (inches) 1½ 2 2½ 3 4 6 8
Port size (inches) 1 1¼ 1½ 1¼ 1½ 2 1½ 2 2½ 2 2½ 3 2½ 3 4 4 5 6 5 6 8
Rated Cv value 11 17 24 17 24 44 24 44 68 44 68 99 68 99 120 120 175 330 175 330 580
Rated travel (mm) 25 38 50 75
Figure 1 Flow characteristicsNote) This graph, indicates typical flow characteristics.
Figure 2 Temperature / normal differential pres-sure ranges requiring Stellite
Note) SCS24 (Precipitation hardedened stainless steel) requires no Stellite.
100
80
60
40
20
00 20 40 60 80 100
Cv
valu
e (%
)
Travel (%)
Stellite1470
{15}
981{10}
490{5}
0-196 0 +100 +200 +300
No
rmal
diff
eren
tial
pre
ssu
re
kgf/
cm2 {k
Pa}
Fluid temperature ( C)
No. SS2-8113-1110 Azbil Corporation
- 4 -
Structural drawing of trim and body/trim material combinationsFollowing table shows typical body/trim material combinations.Please contact us about materials that are not listed in this table.
Note) *1. Material combination; Size 2½" or less is SUS630 and size 3" or over is SCS24.
*2. Material combination; Size 2½" or less is SUS316 and size 3" or over is SCS14A.
*3. Material combination; Size 2½" or less is SUS316 Stellite and size 3" or over is SCS14A Stellite.
Note) *1. Material combination; Size 2½" or less is SUS630 and size 3" or over is SCS24.
*2. Material combination; Size 2½" or less is SUS316 Stellite and size 3" or over is SCS14A Stellite.
a. Integral cage type b. Split cage type (Extension bonnet type1 and nominal size 3" or over)
Figure 3 Structual drawing of trim
Table 3 The valve body material is carbon steel (SCPH2/A216WCB) and plain bonnet.
Figure 3 a
Valve plugSCS24 or SUS630 *1 SCS14A or SUS316 *2 SCS14A Stellite or SUS316 Stellite *3
Cage
Piston ring*1 Ni-resist Stellite #21
Valve stem SUS316
Seat gasket
General Oil-free
Spiral wound(hoop: SUS316, filler: Inorganic paper)
Spiral wound(hoop: SUS316, filler: PTFE)
Bonnet gasket SUS316 SUS316(PTFE coating)
Table 4 The valve body material is carbon steel (SCPH2/A216WCB) and Extension bonnet type1.
Figure 3 a Figure 3 b
Valve plugSCS24 or SUS630 *1
SCS14A Stellite or SUS316 Stellite *2
SCS14A Stellite or SUS316 Stellite *2Cage
Piston ring Stellite #21
Valve stem SUS316
Seat gasketSpiral wound(hoop: SUS316,
filler: Inorganic paper)-
Bonnet gasket SUS316
4 Valve stem
1 Valve plug
6 Bonnet gasket
3 Piston ring
2 Cage
5 Seat gasket
4 Valve stem
6 Bonnet gasket
3 Piston ring
1 Valve plug
2-1 Cage(Upper)
2-2 Cage(Lower)
Azbil Corporation No. SS2-8113-1110
- 5 -
Note) *1. Material combination; Size 2½" or less is SUS630 and size 3" or over is SCS24.
*2. Material combination; Size 2½" or less is SUS316 Stellite and size 3" or over is SCS14A Stellite.
Note) *1. Material combination; Size 2½" or less is SUS316 Stellite and size 3" or over is SCS14A Stellite.
Table 5 The valve body material is stainless steel (SCS13A/A351CF8 or SCS14A/A351CF8M) and plain bonnet
Figure 3 a
Valve plugSCS24 or SUS630 *1 SCS14A Stellite or SUS316 Stellite *2
Cage
Piston ring Stellite #21
Valve stem SUS316
Seat gasket
General Oil-free
Spiral wound(hoop: SUS316,filler: Inorganic paper)
Spiral wound(hoop: SUS316, filler: PTFE)
Bonnet gasket SUS316 SUS316(PTFE coating)
Table 6 The valve body material is stainless steel (SCS13A/A351CF8 or SCS14A/A351CF8M) and extension bonnet type1
Figure 3 a Figure 3 b
Valve plug SCS14A Stellite or SUS316 Stellite *1
SCS14A Stellite or SUS316 Stellite *1Cage
Piston ring Stellite #21
Valve stem SUS316
Seat gasketSpiral wound(hoop:
SUS316,filler: Inorganic paper)
-
Bonnet gasket SUS316
No. SS2-8113-1110 Azbil Corporation
- 6 -
Allowable differential pressureMetal seat (LV) : PTFE packingValves with type PSA, HA and VA actuator
Note) 1) “ ” shows a model with standard actuator.2) : Positioner is necessary.3) Take care not to cause the maximum allowable differential pressure to exceed the maximum operating pressure designated
by ANSI B16. 34-1981 or JIS B2201-1984.4) The upper figures denote the operating allowable differential pressure. The lower denote allowable differential pressure
at full closure.
Table 7 Air-to-close
Actuator model
No.
Supply pressure
kPa{kgf/cm²}
Spring rangekPa
{kgf/cm²}
Posi-tioner
Differential pressure (by nominal size (inches)) kPa {kgf/cm²}
1½ 2 2½ 3 4 6 8
HA2D
160{1.6}
20 to 98{0.2 to 1.0}
1960{20.0}
1960{20.0}
9810{100}
7260{74.0}
390{4.0}
80 to 240{0.8 to 2.4}
1960{20.0}
1960{20.0}
9810{100}
9810{100}
HA3D
160{1.6}
20 to 98{0.2 to 1.0}
1960{20.0}
1960{20.0}
1960{20.0}
1960{20.0}
1960{20.0}
1960{20.0}
9810{100}
9810{100}
9810{100}
9220{94.0}
6960{71.0}
5000{51.0}
390{4.0}
80 to 240{0.8 to 2.4}
1960{20.0}
1960{20.0}
1960{20.0}
1960{20.0}
1960{20.0}
1960{20.0}
9810{100}
9810{100}
9810{100}
9810{100}
9810{100}
9810{100}
HA4D
160{1.6}
20 to 98{0.2 to 1.0}
1960{20.0}
1960{20.0}
1960{20.0}
1960{20.0}
1960{20.0}
9810{100}
9810{100}
9810{100}
8530{87.0}
6860{70.0}
390{4.0}
80 to 240{0.8 to 2.4}
1960{20.0}
1960{20.0}
1960{20.0}
1960{20.0}
1960{20.0}
9810{100}
9810{100}
9810{100]
9810{100]
9810{100}
Table 8 Air-to-open
Actuator model
No.
Supply pressure
kPa{kgf/cm²}
Spring rangekPa
{kgf/cm²}
Posi-tioner
Differential pressure (by nominal size (inches)) kPa {kgf/cm²}
1½ 2 2½ 3 4 6 8
HA2R 270{2.8}
80 to 240{0.8 to 2.4}
1960{20.0}
1960{20.0}
9810{100}
9810{100}
HA3R 270{2.8}
80 to 240{0.8 to 2.4}
1960{20.0}
1960{20.0}
1960{20.0}
1960{20.0}
1960{20.0}
1960{20.0}
9810{100}
9810{100}
9810{100}
9810{100}
9810{100}
6960{71.0}
HA4R 270{2.8}
80 to 240{0.8 to 2.4}
1960{20.0}
1960{20.0}
1960{20.0}
1960{20.0}
1960{20.0}
9810{100}
9810{100}
9810{100}
9810{100}
9710{99.0}
VA5R 270{2.8}
80 to 240{0.8 to 2.4}
1960{20.0}
1960{20.0}
1960{20.0}
9810{100}
9810{100}
9810{100}
PSA6R
400{4.0}
200 to 340{2.0 to 3.5}
1960{20.0}9810{100}
500{5.0}
200 to 390{2.0 to 4.0}
1960{20.0}9810{100}
Azbil Corporation No. SS2-8113-1110
- 7 -
Metal seat (LV) : Graphite packing “P6610+P6528” (+230 to +500 °C)Valves with type PSA, HA or VA actuator
Note) 1) “ ” shows a model with standard actuator.
2) : Positioner is necessary.
3) Take care not to cause the maximum allowable differential pressure to exceed the maximum operating pres-sure designated by ANSI B 16. 34-1981 or JIS B2201-1984.
4) The upper figures denote the operating allowable differential pressure. The lower denote allowable differen-tial pressure at full closure.
Table 9 Air-to-close
Actuator model No.
Supply pres-sure kPa{kgf/cm²}
Spring rangekPa
{kgf/cm²}
PositionerDifferential Pressure (by Nominal size(inches))
kPa {kgf/cm²}1½ 2 2½ 3 4 6 8
HA2D 390{4.0}
80 to 240{0.8 to 2.4}
1960{20.0}
1960{20.0}
9810{100}
9810{100}
HA3D 390{4.0}
80 to 240{0.8 to 2.4}
1960{20.0}
1960{20.0}
1960{20.0}
1960{20.0}
1960{20.0}
1960{20.0}
9810{100}
9810{100}
9810{100}
9810{100}
9810{100}
9810{100}
HA4D 390{4.0}
80 to 240{0.8 to 2.4}
1960{20.0}
1960{20.0}
1960{20.0}
1960{20.0}
1960{20.0}
9810{100}
9810{100}
9810{100}
9810{100}
9360{95.4}
Table 10 Air-to-open
ActuatorModel No.
Supply pressure
kPa {kgf/cm²}
Spring rangekPa
{kgf/cm²}
Positioner
Differential Pressure (by Nominal size(inches))kPa {kgf/cm²}
1½ 2 2½ 3 4 6 8
HA2R
270{2.8}
80 to 240{0.8 to 2.4}
1960{20.0}
1960{20.0}
9810{100}
8190{83.5}
HA3R
1960{20.0}
1960{20.0}
1960{20.0}
1960{20.0}
1960{20.0}
1960{20.0}
9810{100}
9810{100}
9810{100}
9810{100}
7940{80.9}
5620{57.3}
HA4R
1960{20.0}
1960{20.0}
1960{20.0}
1960{20.0}
1960{20.0}
9810{100}
9810{100}
9810{100}
9810{100}
4200{42.8}
VA5R
1960{20.0}
1960{20.0}
1960{20.0}
9810{100}
9810{100}
5450{55.5}
PSA6R
400{4.0}
200 to 340{2.0 to 3.5}
1960{20.0}9810{100}
500{5.0}
200 to 390{2.0 to 4.0}
1960{20.0}9810{100}
No. SS2-8113-1110 Azbil Corporation
- 8 -
Metal seat (LV) : Graphite packing “P6610+M8590” (+500 to +566 °C)Valves with type PSA, HA or VA actuator
Note) 1) “ ” shows a model with standard actuator.
2) : Positioner is necessary.
3) Take care not to cause the maximum allowable differential pressure to exceed the maximum operating pres-sure designated by ANSI B 16. 34-1981 or JIS B2201-1984.
4) The upper figures denote the operating allowable differential pressure. The lower denote allowable differen-tial pressure at full closure.
Table 11 Air-to-close
Actuator model No.
Supply pres-sure kPa{kgf/cm²}
Spring rangekPa
{kgf/cm²}
PositionerDifferential Pressure (by Nominal size(inches))
kPa {kgf/cm²}1½ 2 2½ 3 4 6 8
HA2D 390{4.0}
80 to 240{0.8 to 2.4}
1960{20.0}
1960{20.0}
9810{100}
9810{100}
HA3D 390{4.0}
80 to 240{0.8 to 2.4}
1960{20.0}
1960{20.0}
1960{20.0}
1960{20.0}
1960{20.0}
1960{20.0}
9810{100}
9810{100}
9810{100}
9810{100}
9810{100}
9810{100}
HA4D 390{4.0}
80 to 240{0.8 to 2.4}
1960{20.0}
1960{20.0}
1960{20.0}
1960{20.0}
1960{20.0}
9810{100}
9810{100}
9810{100}
9810{100}
8890{90.6}
Table 12 Air-to-open
Actuator model No.
Supply pres-sure kPa{kgf/cm²}
Spring rangekPa
{kgf/cm²}Positioner
Differential Pressure (by Nominal size(inches))kPa {kgf/cm²}
1½ 2 2½ 3 4 6 8
HA2R
270{2.8}
80 to 240{0.8 to 2.4}
1960{20.0}
1960{20.0}
8900{90.7}
6980{71.1}
HA3R
1960{20.0}
1960{20.0}
1960{20.0}
1960{20.0}
1960{20.0}
1960{20.0}
9810{100}
9810{100}
9810{100}
8840{90.1}
6760{68.9}
4790{48.8}
HA4R
1960{20.0}
1960{20.0}
1960{20.0}
1960{20.0}
1960{20.0}
9810{100}
9810{100}
9810{100}
9070{92.4}
3710{37.8}
VA5R
1960{20.0}
1960{20.0}
1960{20.0}
9810{100}
9810{100}
4640{47.3}
PSA6R
400{4.0}
200 to 340{2.0 to 3.5}
1960{20.0}9810{100}
500{5.0}
200 to 390{2.0 to 4.0}
1960{20.0}9810{100}
Azbil Corporation No. SS2-8113-1110
- 9 -
DIMENSIONSTable 13 Face-to-face dimensions [Unit: mm]
Nominal size
(inches)
A
JIS 10KFF, RFANSI 150RFJPI 150RF
*
JIS 16KRF
JIS 20KRFJIS 30KRFANSI 300RFJPI 300RF
*
JIS 40KRFANSI 600RFJPI 600RF
*
JIS 16KTongue and
groovemale and
female
JIS 20KTongue and
groovemale and
female
JIS 30KTongue and
groove male and
female
JIS 40KTongue and
groovemale and
female
1½ 222 231 235 251 235 236 248 2512 254 263 267 286 265 267 276 286
2½ 276 288 292 311 290 292 303 3113 298 313 317 337 310 317 326 3374 352 364 368 394 360 368 379 3946 451 465 473 508 475 473 486 5088 543 560 568 610 570 568 580 610
Nominal size
(inches)
A
ANSI 150RJJPI 150RJ
ANSI 300RJJPI 300RJ
ANSI 600RJJPI 600RJ
ANSI 150LGJPI 150LG
ANSI 300LGJPI 300LG
ANSI 600LGJPI 600LG
ANSI 150JPI 150SW, BW
*
ANSI 300, 600JPI 300, 600SW, BW
*
1½ 235 248 251 232 244 248 251 2512 267 283 289 264 276 283 286 286
2½ 289 308 314 286 302 308 311 3113 311 333 340 308 327 333 337 3374 365 384 397 362 378 391 394 3946 464 489 511 460 483 505 473 5088 556 584 613 552 578 606 568 610
Note) * : Face-to-face dimensions conform to following standards.- IEC 60534-3-1 : 2001 - IEC 60534-3-3 : 1998 (2½ inches or over) - JIS B 2005-3-1 : 2005 - JIS B 2005-3-3 : 2005 (2½ inches or over)
No. SS2-8113-1110 Azbil Corporation
- 10 -
Note) 1)“H” dimensions are applicable when a hand wheel is not provided. When top mounted hand wheel type HA or VA actuators or side mounted hand wheel PSA6R actuators are used, add the hand wheel dimensions designated in respective specification sheets (No. SS2-8213-0500 for type HA actuators, No. SS2-8210-0100 for type VP actuators, and SS2-PSA100-0100 for type PSA actuators).
2)“H” dimensions of Extension bonnet type 1 are as follows: Upper figures for ANSI 150 and JIS 10K, and lower figures for JIS 16K or ANSI 300 or over.
Table 14 Other dimensions [Unit: mm]
Nominal size (inches)
Actuator Model No.
HB B E
Plain bonnet Extension bonnet
1½HA2D, R 500 665 281 267
70HA3D, R 590 760 363 350
2HA2D, R 500 670 281 267
80HA3D, R 595 765 363 350
2½HA2D, R 575 745/755 281 267
90HA3D, R 630 800/810 363 350HA4D, R 865 1035/1045 520 470
3HA2D, R 580 755/765 281 267
100HA3D, R 635 810/820 363 350HA4D, R 870 1045/1055 520 470
4
HA2D, R 610 810/820 281 267
115HA3D, R 660 860/870 363 350HA4D, R 890 1100/1110 520 470
VA5R 1420 1635 620PSA6R 1255 1470 476
6
HA3D, R 785 1020/1045 363 350
170HA4D, R 955 1190/1215 520 470
VA5R 1480 1740 620PSA6R 1315 1575 476
8HA4D, R 1090 1350 520 470
220VA5R 1585 1850 620
Figure 4 Face-to-face and other dimensions
H
HH
E E E
A A A
B
a. For HA actuator b. For VA5 actuator c. For PSA6R actuator
Azbil Corporation No. SS2-8113-1110
- 11 -
Table 15 Weight [Unit: kg]
Nominal size
(inches)
Actuator Model No.
Weight
Flanged typeJIS 10K
ANSI/JPI 150
Flanged type JIS16K, 20K, 30K
ANSI/JPI 300
Flanged Type JIS 40K
ANSI/JPI 600
Welded typeJIS 10K,16K,20K,
30K, 40KANSI/JPI 150, 300, 600
Plain bonnet
Extension bonnet
Plain bonnet
Extension bonnet
Plain bonnet
Extension bonnet
Plain bonnet
Extension bonnet
1½HA2D,R 31 34 36 39 44 47 36 39HA3D,R 43 46 48 51 56 59 48 51
2HA2D,R 37 40 42 45 47 50 42 45HA3D,R 49 52 54 57 59 62 54 57
2½HA2D,R 43 47 48 52 65 69 48 52HA3D,R 55 59 60 64 77 81 60 64HA4D,R 86 90 91 95 108 112 91 95
3HA2D,R 53 59 63 69 85 91 63 69HA3D,R 65 71 75 81 97 103 75 81HA4D,R 96 102 106 112 128 134 106 112
4
HA2D,R 63 73 78 88 113 123 75 85HA3D,R 75 85 90 100 125 135 87 97HA4D,R 106 116 121 131 156 166 118 128
VA5R 233 243 248 258 283 293 245 255PSA6R 213 223 228 238 258 273 225 235
6
HA3D,R 157 172 187 202 237 252 177 192HA4D,R 188 203 218 233 268 283 208 223
VA5R 315 330 345 360 395 410 335 350PSA6R 295 316 325 340 375 390 315 330
8HA4D,R 268 288 318 338 438 458 308 328
VA5R 395 415 445 465 565 585 435 455
No. SS2-8113-1110 Azbil Corporation
- 12 -
Figure 5 Actuator orientationNote) 1. Indicate by position number when installation other than the standard type is required.
2. With type PSA6R actuator, the side-mounted hand wheel is mounted on the same side as the positioner.
Ordering informationWhen ordering, please specify;
1)2)3)4)5)6)7)8)9)
Model number: HCNNominal size × Port sizeType and rating of end connectionsBody and trim material, necessity of hardeningType of bonnetValve and plug characteristicsType of actuator, air pressure to diaphragmValve action (direct or reverse)Accessories (positioner, hand wheel, pressure regulator with filter, and etc.)
10)
11)12)13)
14)15)
Special requirement of degreasing, copper-free treatment, and etc.Name of flow mediumNormal flow and maximum required flowPressure of flow medium, upstream and downstream pressure at maximum and minimum, required flowTemperature and specific gravity of flow medium Viscosity of flow medium, inclusive or exclusive of slurry
Side-mountedhand wheel
Side-mountedhand wheel
Flowdirection
Flowdirection
Positioner
No.1 (Standard type)
Side-mountedhand wheel
Flowdirection
Flowdirection
Positioner
Positioner
No.2
Side-mountedhand wheel
Flowdirection
Flowdirection
Positioner
No.3
Side-mountedhand wheel
Flowdirection
Flowdirection
Positioner
No.4
Positioner
Please, read ‘Terms and Conditions’ from following URL beforethe order and use.
http://www.azbil.com/products/bi/order.html
(11)
1-12-2 Kawana, FujisawaKanagawa 251-8522 Japan
http://www.azbil.com/
Specifications are subject to change without notice.
No part of this publication may be reproduced or duplicated without the prior written permission of Azbil Corporation.
1st edition: Mar. 20018th edition: Aug. 2015