Introduction
Dear Motor Home Owners,
We would like to congratulate you on the purchase of your new HOBBY motor home and
hope that you will always enjoy traveling with it.
Please read this manual carefully, even if you have been driving a motor home for a longer
period of time. It will help you to avoid operating errors and damage to the vehicle and its
equipment. Correct handling of all technical details will increase your driving comfort and
maintain the value of your motor home.
We wish you and your companions many enjoyable trips and hope you always have a safe
journey.
Your
HOBBY Motor Home Plant
Ing. Harald Striewski GmbH
Introduction
Chapter 1: Introduction
1.1 General information............................................... 01-1
1.2 Before taking your first drive .................................. 01-1
1.3 Designations in the operating instructions ............. 01-2
Chapter 2: Safety
2.1 General information ................................................ 02-1
2.2 Fire protection ........................................................ 02-1
2.3 Road safety ............................................................ 02-2
2.4 What to observe before taking your first drive ....... 02-2
2.5 Before and while driving......................................... 02-3
2.6 Notes for your journey ........................................... 02-5
2.7 Tools on board ....................................................... 02-9
2.8 Emergency equipment ........................................... 02-9
2.9 Maximum speeds ................................................. 02-11
2.10 When you stop driving ......................................... 02-14
Chapter 3: Chassis
3.1 Chassis .................................................................. 03-1
3.2 Loading .................................................................. 03-1
3.3 Leveling supports ................................................... 03-7
3.4 Entrance steps ....................................................... 03-8
3.5 Externally mounted constructions ......................... 03-9
Chapter: Wheels, Tyres, Brakes
4.1 Wheels ................................................................... 04-1
4.2 Tyres ....................................................................... 04-1
4.3 Inflation pressure .................................................... 04-2
4.4 Tread depth ............................................................ 04-2
4.5 Wheel rims ............................................................. 04-3
4.6 Snow chains ........................................................... 04-3
4.7 Spare tyre ............................................................... 04-3
4.8 Tyre repair kit .......................................................... 04-4
4.9 Changing the tyre ................................................... 04-7
4.10 Brakes .................................................................... 04-7
Chapter 5: Exterior Structure
5.1 Overview of tank and service flaps ........................ 05-1
5.2 Ventilation ............................................................... 05-3
5.3 Opening and closing doors and flaps .................... 05-5
5.4 Exterior mirror ........................................................ 05-9
5.5 Condensation in headlight systems ....................... 05-9
Chapter 6: Electrical Installations
6.1 Safety instructions ................................................. 06-1
6.2 HOBBY on-board control panel ............................. 06-1
6.3 Electric power supply ............................................. 06-6
6.4 Function of the power generating unit ................... 06-7
00-1
Introduction
6.5 Caravan battery .................................................... 06-10
6.6 Fuse protection of the electric system ................. 06-11
6.7 Interior circuit diagrams ....................................... 06-13
6.8 Subsequently installed devices ............................ 06-29
Chapter 7: Interior of the Caravan
7.1 Opening and closing doors and flaps .................... 07-1
7.2 Windows ................................................................ 07-2
7.3 Caravan skylight ..................................................... 07-4
7.4 Remi-Star sunroof and blind .................................. 07-5
7.5 Dimming system for driver's cabin ...................... 07-10
7.6 Seating chests and setting up beds .................... 07-11
7.7 Overview of seating arrangements ...................... 07-13
7.8 Overview of day and night positions .................... 07-14
7.9 Seats in the caravan ............................................ 07-21
7.10 Seatbelts in the caravan....................................... 07-21
7.11 Seats in the driver's cabin .................................... 07-22
7.12 Media unit ............................................................ 07-22
7.13 Bunk beds/alcoves .............................................. 07-23
Chapter 8: Water
8.1 Water supply .......................................................... 08-1
8.2 Flushing toilet ........................................................ 08-4
8.3 Hot water supply .................................................... 08-9
Chapter 9: Gas
9.1 General safety rules for using LPG fittings ............ 09-1
9.2 Gas supply ............................................................. 09-3
9.3 Heating ................................................................... 09-5
9.4 Refrigerator ............................................................ 09-7
9.5 Gas cooker ............................................................. 09-7
Chapter 10: Accessories
10.1 Towbar coupling ..................................................... 10-1
Chapter 11: Maintenance and Care
11.1 Maintenance .......................................................... 11-1
11.2 Airing ...................................................................... 11-1
11.3 Care ........................................................................ 11-2
11.4 Operating in winter ................................................. 11-4
Chapter 12: Sanitation and Environmental Protection
12.1 Traveling in the environment .................................. 12-1
12.2 Returning the vehicle ............................................. 12-3
Chapter 13: Technical Data............................................. 13-1
13.1 Weights acc. to 92/21/EWG, 2007 season ............ 13-1
13.2 Inflation pressure of tyres ...................................... 13-2
Index .................................................................................. I-1
Appendix ............................................................................A-1
00-2
Introduction01-1
Chapter 1: IntroductionOur motor homes are continuously being further developed and for this reason we must reserve the right to make changes to the equipment, shape and technology. Certain kinds of accessories are also described in this user manual that are not part of the standard scope of delivery. For this reason, no claims may be asserted against HOBBY based on the conten-ts of this user manual. Those accessories that are available at the time of going to print are described here. They have been applied on a par for all floor plans. Please note that it was not possible to describe all of the individual variations here. If you have any special questions concerning accessories or the technology of the vehicle, your dealer will be happy to answer them.
1.1 General information Your HOBBY motor home has been built in accordance with the latest technology and approved safety regulations. Despite all precautionary measures, however, it is possible that pas-sengers may be hurt or the motor home damaged if the sa-fety instructions in this user manual and the warning stickers placed throughout the motor home are not observed. Please use the motor home only when it is technically in top condition.
Any defects that affect the safety of passengers or the motor home should be remedied immediately by trained personnel.The brake system and the gas system should only be checked and repaired by an authorised workshop.Please ensure that all of the deadlines for checking equipment and inspections are met.
1.2 Before taking your first drive
Please do not consider this manual to be just a means of refe-rence, but familiarize yourself thoroughly with it before taking your first drive.
Fill out the guarantee cards in the different manuals for the instal-led equipment and fittings and send them to the manufacturers. This will ensure guarantee claims for any of the equipment.
In accordance with guarantee conditions, HOBBY's dealer will give you a 5-year guarantee on the consistency of the motor home. Your dealer will give you a guarantee booklet, “5 Years‘ Guarantee on Consistency“ when you pick up your vehicle.
Note: If a consistency test has not been carried out, you will forfeit any claims for a 5-year guarantee on consistency.
Introduction 01-2
1
Please note the following before operating the vehicle:• Check the tyre pressure. Please refer to the section on tyre pressure.• Load the vehicle correctly. Keep to the technically per-
missible overall mass. Please refer to the section on loading.• Load the batteries fully before each journey Please refer to the section on the starter and accommoda-
tion batteries.• If the temperature outside is below 0° C, heat the vehicle
before filling up the water system. Please refer to the section on water supply/filling the fresh
water tank.• Tighten the wheel nuts after having driven the first 50 km.• Switch off all fitted devices that operate on gas before
filling the petrol tank.• Tightly strap gas bottles in the gas bottle box during
transportation.• When camping in winter, heat the vehicle at night if
there is danger of frost. Please refer to the section on operating in winter/heating.• Keep compulsory ventilation clear. Please refer to the section on windows/roof fan/airing.• When the vehicle is not in use, empty the entire water
system and leave the water faucets open in a neutral position. This prevents the water system from being damaged by frost.
Please refer to the section on emptying the water sy-stem.
1.3 Designations in the operating instructions
This manual explains the motor home in the following man-ner:
Texts and illustrationsTexts that refer to illustrations are found directly below the illustrations.Details in illustrations (here: entrance) have been given item numbers (1).
ListsLists are given in the form of key words and shown as bullet points using “-“.
Introduction01-3
Handling instructionsHandling instructions are also given in the form of key words beginning with the symbol “•“.
Notes
Notes point out important details that ensure your motor
home and its fittings will function perfectly. Please remem-
ber that there may be some differences in description to the
various kinds of equipment that can be supplied.
Warnings
Warnings make you aware of dangers that may lead to
material being damaged or even people being hurt if they
are not observed.
Environmental Tips
Environmental tips give you possibilities for lessening the
impact on the environment.
Introduction
Safety
Safety
Chapter 2: Safety 2.1 General information
• Ensurethatthereissufficientventilation.Nevercoverbuilt-incompulsoryventilation(skylightswithcompulsoryventila-tionorrooffan).Keepcompulsoryventilationfreeofsnowandleaves-dangerofsuffocation!
• Note theheadroomof theentrancedoorand thedriver'sdoor.
• Operatinganduserinstructionsforbuilt-inequipment(refri-gerator,heating,cooker,etc.)aswellasforthebasicvehiclemustbeobservedatalltimes.
•Ifaccessoriesoroptionalequipmentistobeinstalled,thismay change the measurements, weight and road perfor-manceofthemotorhome.Someaccessoriesmustbere-gistredandenteredinthevehicle'spapers.
• Useonlytyresandrimsthathavebeenapprovedforyourmotorhome.Pleaserefertothevehicle'sregistrationpapersforinformationontyreandrimsizes.
• Alwaysusetheparkingbrakewheneveryouparkthemotorhome.
2.2 Fire protection Precautions against fire•Neverleavechildrenaloneinthevehicle.•Keepinflammablematerialsawayfromallheatingandcoo-kingdevices.
• Anychangestotheelectricsystem,gassystemorbuilt-indevices may only be carried out by an authorised work-shop.
•Installafireextinguishernexttothemainentrance.•Familiariseyourselfwiththeinstructionsonthefireextingu-isher.
• Storeafireblanketnearthecooker.•Donotblockanyescaperoutes.•Familiariseyourselfwithallsafetymeasuressetupontheproperty.
Fighting fire• Immediatelyevacuateallpassengers.•Shutthevalvesofthegasbottles.•Turnofftheelectricsupply.•Soundthealarmandcallthefiredepartment.•Onlyfightthefireyourselfifyoucandosowithoutrisk.
02-1
Safety
2.3 Road safety
•Beforedriving,check that thesignaland lightequipment,steeringandbrakesallfunctionproperly.
•Ifthevehiclehasbeenstandingforalongerperiodoftime(approx. 10months) have an authorisedworkshop checkthebrakesystemandthegassystem.
•Completely open and fasten the dimming system on thefrontandsidewindows.
•Passengersmaynotstayinthealcoveswhiledriving.•Inwinter,theroofmustbeclearedofsnowandicebeforedriving.
•Regularlycheckthetirepressurebeforedriving.Falsetirepressurecancauseexcessivewear,damagetothetiresorevenleadtoabursttire.
•Children'sseatsmayonlybemountedonseatsthathaveathree-pointseatbeltinstalledbythefactory.
•Turnthereversibleseatsinthedirectionoftravelandlockthem.Theseatsmaynotbeturnedwhiledriving.
02-2
2.4 What to observe before taking your first drive
Vehicle registrationEveryvehiclethatdrivesonpublicroadsmustberegistered.Thisalsoappliestoyournewmotorhome.ApplyforregistrationatyourlocalDriverandVehicleLicensingAgency.
Youmustshowthefollowingwhenapplyingforregistration:- registrationdocument,PartII- insurancecoverage- proofofpersonalidentityorconfirmationofregistra- tionbyalocalauthority- if applicable, power of attorney to register the vehicle.
General inspectionIn accordancewithSection 29 of theGermanRoadTrafficLicensingRegulations,yourmotorhomemustundergoagene-ralinspectioneverytwoyearsduringthefirst72months,afterwhichageneralinspectionmustbecarriedouteveryyear.ThisgeneralinspectioncanbecarriedoutbytheGermanTechnicalSurveyanceAssociation(TÜV),theGermanMotorVehicleSurve-yanceAssociation(DEKRA)oranofficiallyapprovedexpert.
Safety02-3
2.5 Before and while drivingAstheowner/driverofthevehicle,youareresponsibleforthestateofthevehicle.Pleaseobservethefollowingpoints:
ExteriorChecktheexteriorofthevehicleandcarryoutthefollowingpreparationsbeforedriving:
Preparing the vehicle• Ifthelevelingsupportshavebeenextended,retractthem.• Closeallofthewindowsinthemotorhomeaswellasthe
skylightsintheroof.• Close and secure the entrances to the caravan and the
serviceflaps.
Foreachgeneralinspectionyoumustshowthefollowing:- registrationdocument,PartI- validgastestcertificateforgasinstallation. The initial certificatewill begiven to you together withtheregistrationdocument.
Anychangesmade to the vehicle that underlieGerman
Road Traffic Licensing Regulationsmust be officially
authorised!
Ifyouhaveanyfurtherquestionsordifficulties,yourautho-
risedHobbydealerwillalwaysbeavailabletoassistyou!
Safety 02-4
• Closethetapforthesewagetank.• Closealltapsandquick-actionstopvalvesforgasdevices.
Theonlyexceptionisforheatersthataretobeusedwhiledriving.
• Ifnecessary,removeanyelectriccablesfromtheexteriorsocket.
• Ifnecessary,retracttheTVantennaasforaspossible.• Ifnecessary,secureanyloadsontheroof,ensuringthatthey
willnotslide.• Thesameappliesforbicycles.
• Turnoffthelightinthetentinfrontofthemotorhome.
InteriorSomepreparationsmustalsobecarriedoutinsidethemobilehome.
Preparing the interior• Sortlooseobjectsandstowtheminthecompartments.• Placeheavyobjectsinthelowercompartments.• Ifnecessary,switchrefrigeratorto12Voperation.• Ensurethatnoliquids,includingthoseintherefrigerator,will
leak.• Securegasbottles.• Bracethesafetydeviceforthetable.• Firmlyclosedoors(includingrefrigeratordoor),drawersand
flaps.
• Heavyand/orvoluminousobjects(e.g.TV,radio)mustbesecuredbeforedriving.
• Completelyopenandsecuretheoptionalcockpitdimmingsystem.
Donotoverloadthevehicle!Itisimperativethatyounotethe
permissibleaxleloads,thetechnicallypermissibleoverall
massaswellasthepermissibleheight,widthandlength
ofthemobilehome.
Placeanotewithallimportantmeasuresandweightsina
visibleplaceinboththecaravanandthedriver‘scabin.
Safety02-5
Driver‘s cabin
Do not forget the following:• Adjust the interior and exteriormirrors aswell as your
seat.• Checkthelights.
In addition:• Checkyourtirepressure.• Checkallliquids,suchasoil,coolingwater,brakefluidand
windscreencleaningliquid,andfillthemupifnecessary.• Turnoff all gasdevices (heating, refrigerator, etc.) before
puttingpetrolinthetank.
Note:Neveruseyourcellphoneatthepetrolstation.
Before driving offBeforeyoudriveoffyoushouldbeabletoanswerthefollowingquestionswith“yes“:• Isthereafirst-aidkitandawarningtriangleonboard?• Are all the lightsworking (headlights, dippedheadlights,
brakelightsandblinkers)?
2.6 Notes for your journey
Your mobile home is not an automobile!Inmanysituations,itreactsverydifferentlytoa“normal“au-tomobile.Therefore,youshouldbepreparedforthefollowingdifferences:
LoadingThe following applies for loading:• Loadevenly.Heavyorbulkyobjectsshouldbeplacedinthe
lowercompartments!• Tiedownroofloadssecurely!• In the interior, store luggage in cupboards andcompart-
ments.
Safety 02-6
• Securealldoorsandflaps.• Afteryouhavefinishedloading,checktheoverallweighton
apublicscales.
Donotexceedaxleloadsandpermissibleoverallweight.
Roof load (50 kg maximum)Theheightofthemobilehomemayvaryfromonejourneytothenextduetodifferentroofloads.
The following applies for roof loads:• Addthemeasurementoftheroofloadtotheheightofthe
mobilehome.• Placea note visibly in thedriver's cabgiving theoverall
height.Thissaveshavingtocalculatetheheightwhendrivingunderbridgesandthroughtunnels.
Braking
The following applies for braking:• Notethelongerlengthofthebrakepath,especiallyonwet
roads.• Whendrivingdownhill,selectagearthatisnothigherthan
whendrivinguphill.
Shunting
Your mobile home is far larger than an automobile.
The following applies for shunting:• Eveniftheexteriormirrorshavebeensetcorrectly,thereis
anextremelylargeblindangle.• Useassistancefromotherpersonstoparkinplaceswhere
youhaveadifficultview.
Passenger safety
The following applies while driving:• Onlythoseseatsmaybeusedbypassengersthatareequip-
pedwithasafetybelt.• Whiledriving,passengersmaynotestayinthealcoveorthe
beds.• Passengersmustremainintheirseatswiththeirseatbelt
on!• Donotopenthedoorlatch!• Noextrapassengersmayremaininthevehicle!
Safety02-7
Driving
Takeatrialdrivebefore leavingonyourfirst large journey inordertofamiliarizeyourselfwiththemobilehome.Remembertopractisedrivingbackwards.
The following applies for driving:• Donotunderestimatethelengthofthemobilehome.• Becarefulwhendrivingintoinnercourtyardsandthrough
entrancegates.• Themobilehomemaystart toswingfromsidetoside in
cross-winds,onwetoricyroads.• Adjustyourspeedtoroadandtrafficconditions.• Longdescentswithaslightgradientcanbecomedangerous.
Adjustyourspeedfromtheverybeginningtoallowyoutospeed up if necessarywithout endangering other auto-mobiles.
• Asageneralrule,neverdrivefasterdownhillthanuphill.• Themobilehomemaybecaughtupinaslipstreamwhen
overtakingorbeingovertakenbylorrieswithtrailersorbuses.Thiseffectiscounteractedbylightlycounter-steering.
Driving in reverse
The following applies for driving in reverse:• Use theassistanceofapersonoutside thevehiclewhen
drivinginreverse.
Driving through curvesDuetoitsheight,amobilehomebeginstoswaymorequicklythananautomobile.
The following applies for driving through curves:• Neverdrivetooquicklyintoacurve!
Driving economicallyThemotorofyourmobilehomehasnotbeendesignedtodriveconstantlyunderafullload.
The following applies when driving:• Donotkeepyourfootdownonthegas!• Thefinal20km/hbeforereachingtopspeedrequireupto
50%morefuel!
Getting petrolAnumberofdevicesthatuseanopenflamehavebeenbuiltintoyourmobilehome.
Safety 02-8
The following applies when getting petrol:• Turnoffallgasdevices(heating,refrigerator,etc.)!• Turnoffallcellphones!• Nevergetanythingotherthandieselfuel.• Nevermistakenlyfillthefreshwatertankwithfuel.
Saving energy in winter
It isveryeasytosaveenergy insideyourmobilehome.Thisappliesespeciallytoheatinginwinter.
The following applies for saving energy:• Meter the exact useof ventilation in the vehicle and the
heatingvalve.• Installwintermatsontheinnersidesofthedriver‘scabin
andthewindscreen(notincludedinscopeofdelivery).• Installaninsulationmatbetweenthedriver‘scabinandthe
caravan(notincludedinscopeofdelivery).• Usealuminium-coatedwindowmats andwindowblinds.
Theseofferprotectionagainstboththecoldandtheheat.• Openthedooraslittleandasbrieflyaspossible.• Whencampinginwinter,itispossibletoputupasmalltent
infrontofthevehicleasprotectionagainstthecold.
Safety02-9
Reflective jacket(notincludedinscopeofdelivery)Inacc.withEN471,werecommendthatyoucarryandwearareflectivejacketwithwhiteretro-reflectivestripeswheneveryouleavethevehicleonopenroadsandemergencystrips.Thedrivershouldwearthisjacketwhenthevehicle• comestoastopoutsidecitylimitsonanobscureruralroad
becauseofanaccidentorbreakdown,iftheviewispoorduetobadweather,intwilightordarkness,or
• whenitmustbesecuredbymeansofawarningtriangleon theemergencystripof themotorwaybecauseofanaccidentorbreakdown.
2.7 Tools on board
Toolsonboardarelocatedinsidetheentrancestep.
Tobepreparedincaseofanemergency,youshouldalwayscarry the three emergencydevicesonboard and familiarizeyourselfwiththem.
First-aid kit (standardequipment)The first-aid kit should alwaysbeat handandhavea fixedpositioninyourmobilehome.Anyobjectsremovedfromthefirst-aidkitshouldbereplacedimmediately.Expirydatesshouldbecheckedregularly.
2.8 Emergency equipment
Safety 02-10
100 m
Warning triangle (standardequipment)Thewarningtriangleshouldalsoalwaysbeathandandhaveafixedpositioninyourmobilehome,preferablytogetherwiththefirst-aidkit.
In an emergency• Setup thewarning triangleat least100m in frontof the
dangerzone!
Fire extinguisher (not included in scope of delivery)Familiarizeyourselfwithhowtooperatethefireextinguisher.Payattentiontothedatewhenitmustberefilled!Thefireex-tinguishermustbecheckedevery2years.
Precautions against fire• Neverleavechildrenaloneinthevehicle.• Familiarizeyourselfwiththepositionanduseoftheemer-
gencyexits.• Donotblockanyescaperoutes.• Keepinflammablematerialsawayfromallheatingandcoo-
kingdevices.• Installafireextinguishernexttothemainentrance.• Storeafireblanketnearthecooker.• Familiarizeyourselfwiththeinstructionsonthefireextingu-
isher.• Familiarizeyourselfwithallsafetymeasuressetupagainst
fireontheproperty.
Fighting fire• Evacuateallpassengers.• Closethevalvesofthegascontainers.• Turnofftheelectricsupply.• Soundthealarmandcallthefiredepartment.• Onlyfight thefirebyyourself if thiscanbedonewithout
risk.
Safety02-11
2.9 Maximum speeds
Neverexceedthemaximumspeedofthecountryinwhichyouaredriving!ThefollowingtableliststhemaximumspeedsformobilehomesinEuropeancountries.(Status:2000-01-03)
Belgium 2,50 12 upto7,5 50 90/120*1 120 over7,5 60/90*1 90Bulgaria 2,60 11 upto7,5 50 90 120 over7,5 70 100Denmark 2,55 12 upto3,5 50 80 110 over3,5 70 70Germany 2,55 12 upto3,5 50 100 130*2 3,5upto7,5 80 100*19 over7,5 60 80Estonia 2,50 12 upto3,5 50 90 110 over3,5 70 90Finland 2,60 12 50 80*15 80*15France 2,50 12 upto3,5 50 90*3/110*1;3 130*3 over3,5 80*3/100*1;3 110*3Greece 2,50 12 50 110/120*1 120GreatBritain 2,55 12 48 96/112*1 112Ireland 2,50 12 48 96/112*1 112Iceland 2,55 12 50 90*4Italy 2,55 12 upto3,5 50 90/110*1 130 over3,5 80 100Yugoslavia 2,50 12 upto3,5 60 80/100*1 100 over3,5 80 80Croatia 2,55 12 50 80/100*1 130*18Latvia 2,50 12 upto7,5 50 90*2 90Lithuania 2,50 12 upto3,5 50 90 110*9 over3,5 70
Country Measurements(m) Permissibleoverall Maximumspeed(km/h)
width length weight(t) incities outsidecities onmotorways
Safety 02-12
Macedonia 2,50 12 50/60 80 80Netherlands 2,55*14 12 50 80/100*1 120Norway 2,55 12,4 upto3,5 50 80/90*1 90 3,5over7,5 80 80Austria 2,55 12 upto3,5 50 100 130*8 3,5over7,5 70 80Poland 2,50 12 upto2,5 60 90 130 over2,5 70 70Portugal 2,55 12 upto3,5 50 90/100*17 120*7 over3,5 80/90*17 90Romania 2,50 12 upto3,5 50 90 90 over3,5 40 60 60Russia 2,50 12 50 90*10 90*10Sweden*16 2,60 24 upto3,5 50 70/90*17 110 over3,5 80/90*1 90Sweden 2,60 24 upto3,5 50 70/90 110 over3,5 80/90 90Switzerland 2,55 12 upto3,5 50 80/100 120 over3,5*12 100 100TheSlovakian 2,50 12 upto3,5 60 90 130Republic 3,5upto6,0 80 80Slovenia 2,55 12 upto3,5 50 80/100 100 over3,5 80 80Spain 2,55 12 50 80/90/100 100TheCzech 2,50 12 upto3,5 50 90 130Republic over3,5 80 80Turkey 2,50 10 50 80 130TheUkraine 2,50 12 60 90 110Hungary 2,50 12 upto3,5 50 80/100 120 over3,5 70 80Cyprus 2,50 16,5 50 80 100
Country Measurements(m) Permissibleoverall Maximumspeed(km/h)
width length weight(t) incities outsidecities onmotorways
Safety02-13
*1: Onexpressways.*2: Recommendedspeed130km/h.*3: Reducespeedby10km/honwetroadsandby20km/honmotorways.*4: Ongravelroads:80km/h.*5: Onroadswithmorethanonelaneinbothdirections.*6: Onmotorways.*7: Adriverwhohasnotheldhislicenceformorethanoneyearmaynotdrivefasterthan90km/h. Correspondingstickers(availableintheofficesoftheACP)mustbeappliedvisiblytotherear ofthevehicle.*8: From10p.m.to5a.m.:110km/honallmotorwayswiththeexceptionoftheA1(Salzburg-Vienna) andtheA2(Salzburg-Villach).*9: Upto1100ccm:70km/h,upto1800ccm:80km/h,over1800ccm:90km/h.*10. 70km/hifthedriverhasheldhislicenceforlessthan2years.*11: InaccordancewithSection57aoftheGermanRoadTrafficLicensingRegulations,vehicleswitha maximumoverallweightofmorethan7.5trequireatachograph.However,itisindisputewhetherthis isalsoapplicableformotorhomesthatareprivatelyused.*12: Aheavyvehiclefeemustbepaidonallroadsforallvehicleswithamaximumoverallweightofmorethan3.5t.*13: Theexperienceofthepastfewyearshasshownthatobjectionsarenolongerraisedwithregardto extra-wideorextra-longGermanvehicles.*14: 2.55monallmainroads;2.20monallroadsmarked“B“.*15: Motorhomesthatwerefirstregisteredfrom1995onwardswithanemptyweightof1,875kgaswellasthose firstregisteredfrom1981onwardswithanemptyweightoof1,800kgmaydriveamaximumof100km/h.*16: AclosedsewagesystemisoftenmandatoryonSwedishcampinggrounds.*17: Inaccordancewiththesigns.*19: 12thexceptiontotheGermantrafficregulationsfortheGermanRoadTrafficRegulationsdated2005-03-18.
Notetrafficregulationsnos.253,273and277inaccordance
withSection41oftheGermanRoadTrafficRegulations.
AlsonoteSections3,7and18oftheGermanRoadTraffic
Regulations.
Safety 02-14
Water systemEmptytheentirewatersystemifthevehicleisnotheatedwhenthereisdangeroffrost.Leavethewaterfaucetsaswellasalldrainvalvesopentopreventdamagefromfrost.Water thathasbeen left to stand in the freshwater tankorwaterpipesquicklybecomesundrinkable.Therefore,alwaysflushthewaterpipesthoroughlywithseverallitresoffreshwa-terbeforeusingthem.
2.10 When you stop driving
Selecting a parking space
The following applies for selecting a parking space:• Selectaparkingspacethatisaslevelaspossible.• Ifpossible,pickyourspotindaylight.
Securing the vehicle
The following applies when securing the vehicle:• Putthevehicleingear.• Pullonthehandbrake.• Ifnecessary,extendextravehiclesupports.• Ifnecessary,useblocks(notinscopeofdelivery).
Ifthetemperatureisbelow0°,onlypullthehandbrakeon
lightlyandensurethatthevehicleisingeartopreventthe
handbrakefromfreezing!
Whenturningthedriver‘seat,ensurethatyoudonotacci-
dentlydisengagethehandbrake.
Switching electric consumption:
The following applies when switching electric consump-tion:• Switchtherefrigeratorfrom12Vtogasor230V.Otherwise,
ifthemotorisnoton,the12Velectricalsupplywillautoma-ticallyturnitselfoffafterafewminutes.
Chassis
Chassis03-1
Definition of Masses for Mobile Homes (2007)Throughout Europe, EU Guideline 92/21/EWG is applicable for calculating the masses (weights) and resulting loads for mobile homes. The terms and basis used for calculations are exp-lained below.
1. Technically permissible overall massThe figure for the technically permissible overall mass is ba-sed on information given by the Hobby Mobile Home Plant in cooperation with the manufacturer of the base vehicle. This mass was determined in extensive calculations and tests and, for safety reasons, it may not be exceeded under any circum-stances.
2. Mass when the vehicle is ready to startThe mass when the vehicle is ready to start corresponds to the mass of the empty vehicle including lubricants, tools, spare tyre (and/or repair kit), petrol (100 %), booster battery, all of the standard equipment mounted by the factory as well as 75 kg for the driver, plus basic equipment (gas, water, electric).
3. Basic EquipmentThe basic equipment includes all of the equipment and liquids that are necessary to ensure safe and proper use of the vehicle. This includes the weights of:
Chapter 3: Chassis
3.1 ChassisThe chassis includes parts of the frame and the axles. No technical changes may be made, as otherwise the general type approval will expire!
Technical changes may only be carried out after being
released by the manufacturer.
For further information, please refer to the enclosed ope-
rating instructions for the basic vehicle.
3.2 LoadingThe maximum axle loads as well as the technically permis-
sible overall mass entered in the vehicle‘s documents may
not be exceeded.
Weights of mobile homes in accordance with 92/21/EWG
Please refer to the definition of masses for mobile homes!
Chassis 03-2
a) Supply of liquefied petroleum gas
No. of 11 kg gas bottles 1 2 2
No. of 5 kg bottles 1 - -
Weight of an 11 kg aluminium bottle 5.5 5.5 5.5
Weight of a 5 kg steel bottle 6.0 - -
Weight of 11 kg gas inflation (90 %) 9.9 9.9 9.9
Weight of 5 kg gas inflation (90 %) 4.5 - -
Total: 26 31 31
b) Liquids
100 l fresh water tank (90 %) 90 90 -
10 l fresh water tank (90 %) - - 9
Total basic equipment: 116 121 40
Siesta
T 555 FS T 555 AK
FS
4. LoadingLoading corresponds to the difference between the "technically permissible overall mass" and the "mass when the vehicle is rea-dy to start". This value must take into consideration the masses for passengers (conventional load: 75 kg x no. of seats, driver excepted), additional equipment and personal belongings.
The mass when the vehicle is ready to start includes an additi-onal value for liquids and gas, etc. (see basic equipment). Part of this additional value can also be used for additional loads if, for example, you would like to travel with empty water tanks or without gas bottles.
T 555 AK LC
T 600 ...T 650 ...
T 650 ...Reduced load
capacity
3500 kg
Check to ensure that the masses of all objects transported
in the mobile home have been taken into consideration, e.g.
passengers, additional equipment, basic equipment and
personal belongings such as clothes, food, pets, bicycles,
surfboards, other sport equipment, etc.).
Under no circumstances may the technically permissible
total load be exceeded when the mobile home has been
loaded.
Chassis03-3
5. Reduced load capacity for T 650 to 3500 kg
Before driving, you must open the overflow valve for the fresh water tank.
To reduce the weight when the vehicle is ready to start, the fresh water tank has been fitted out with an overflow valve, located to the right in the seat and marked with a warning sign. Before you begin driving, open the overflow valve. The contents of the fresh water tank will run off until, for weight reasons, only approx. 10 litres are left. When the vehicle is standing, the valve can be closed, allowing you to use the full volume of the tank.A reduced fresh water supply when the vehicle is ready to start has been entered in the vehicle's registration papers. The mo-bile home may only be operated on public roads when the overflow valve is open. The driver is responsible for ensuring that this requirement is fulfilled as well as for observing the technically permissible total weight.
Chassis 03-4
Masses in standard condition, 2007 season
These figures refer to the standard vehicle without extra equipment. Deviations of up to 5 % are possible.
Model
Series
Weight of basic vehicle
Driver Die-sel
[kg]
Basic equip-ment
Mass when
vehicle is ready to
start
Techn. perm. total
weight
Load
No. of seats
Conventi-onal load
Overload weight
Length of vehicle
Personal belon-gings
Remai-ning add.
weight
T 555 FS Siesta (C) 2560 75 68 116 2819 3500 681 4 225 456 5,8 98 358
T 600 FC Siesta (C) 2625 75 68 121 2889 3500 611 3 150 461 6,4 94 367
T 600 GFLC Siesta (C) 2720 75 68 121 2984 3500 516 4 225 291 6,4 104 187
T 600 GFS Siesta (C) 2710 75 68 121 2974 3500 526 4 225 301 6,4 104 197
T 650 FLC Siesta (D) 2835 75 68 121 3099 3850 751 4 225 526 7,1 111 415
T 650 FLC Siesta (D) 2835 75 68 40 3018 3500 482 4 225 257 7,1 111 146
T 650 GFLC Siesta (D) 2870 75 68 121 3134 3850 716 4 225 491 7,1 111 380
T 650 GFLC Siesta (D) 2870 75 68 40 3053 3500 447 4 225 222 7,1 111 112
T 555 AK LC Siesta (C) 2687 75 68 121 2951 3500 549 4 225 324 5,8 98 226
T 555 AK FS Siesta (C) 2645 75 68 116 2904 3500 596 4 225 371 5,8 98 273
T 600 AK GFLC Siesta (C) 2790 75 68 121 3054 3500 446 4 225 221 6,4 104 117
T 650 AK FLC Siesta (D) 2885 75 68 121 3149 3850 701 4 225 476 7,1 111 365
T 650 AK FLC Siesta (D) 2885 75 68 40 3068 3500 432 4 225 207 7,1 111 97
T 650 AK GFLC Siesta (D) 2899 75 68 121 3163 3850 687 4 225 462 7,1 111 351
T 650 AK GFLC Siesta (D) 2899 75 68 40 3082 3500 418 4 225 193 7,1 111 83
T 650 AK KLC Siesta (D) 2872 75 68 121 3136 3850 714 4 225 489 7,1 111 378
T 650 AK KLC Siesta (D) 2872 75 68 40 3055 3500 445 4 225 220 7,1 111 110
Chassis03-5
Tires and rims for basic mobile home vehicles, 2007 season
HobbyModel
Series Techn. perm. overall weight
[kg]
Perm. axle loadfront rear
Tire size Wheel attachment*
Steel rims Tire size Wheel attachment*
LMrims
Rim designation
T 555 FS Siesta (C) 3500 1750 2250 215/75 R 16 C 5 / 65 / 160 5½ J x 16, ET 56 215/75 R 16 C 5 / 65 / 160 6½ J x 16, ET 60 CWC65640
T 600 FC Siesta (C) 3500 1750 2250 215/75 R 16 C 5 / 65 / 160 5½ J x 16, ET 56 215/75 R 16 C 5 / 65 / 160 6½ J x 16, ET 60 CWC65640
T 600 GFLC Siesta (C) 3500 1750 2250 215/75 R 16 C 5 / 65 / 160 5½ J x 16, ET 56 215/75 R 16 C 5 / 65 / 160 6½ J x 16, ET 60 CWC65640
T 600 GFS Siesta (C) 3500 1750 2250 215/75 R 16 C 5 / 65 / 160 5½ J x 16, ET 56 215/75 R 16 C 5 / 65 / 160 6½ J x 16, ET 60 CWC65640
T 650 FLC Siesta (D) 3850 1750 2600 185/75 R 16 C 6 / 139 / 178 5 J x 16, ET 107 --- --- --- ---
T 650 GFLC Siesta (D) 3850 1750 2600 185/75 R 16 C 6 / 139 / 178 5 J x 16, ET 107 --- --- --- ---
T 555 AK LC Siesta (C) 3500 1750 2250 215/75 R 16 C 5 / 65 / 160 5½ J x 16, ET 56 215/75 R 16 C 5 / 65 / 160 6½ J x 16, ET 60 CWC65640
T 555 AK FS Siesta (C) 3500 1750 2250 215/75 R 16 C 5 / 65 / 160 5½ J x 16, ET 56 215/75 R 16 C 5 / 65 / 160 6½ J x 16, ET 60 CWC65640
T 600 AK GFLC Siesta (C) 3500 1750 2250 215/75 R 16 C 5 / 65 / 160 5½ J x 16, ET 56 215/75 R 16 C 5 / 65 / 160 6½ J x 16, ET 60 CWC65640
T 650 AK FLC Siesta (D) 3850 1750 2600 185/75 R 16 C 6 / 139 / 178 5 J x 16, ET 107 --- --- --- ---
T 650 AK GFLC Siesta (D) 3850 1750 2600 185/75 R 16 C 6 / 139 / 178 5 J x 16, ET 107 --- --- --- ---
T 650 AK KLC Siesta (D) 3850 1750 2600 185/75 R 16 C 6 / 139 / 178 5 J x 16, ET 107 --- --- --- ---
* No. of tire bolts / centralising collars / bolt circle
Basic model with steel rims Basic model with LM rims
Chassis 03-6
Weight of accessories, T Series
Object Weight (kg)
Additional exterior storage flap 1.0Air-conditioning B 1901 (Dometic) (230 V) 31.0Air-condition B 2000 (Dometic) (230 V) 34.0Air-conditioning Truma Frostair 1700 26.3Air-conditioning via vehicle engine 20.0Alarm system 1.0Bicycle carrier for 2 bicycles 7.2Bicycle carrier for 3 bicycles 8.3Carpet 6.0 - 11.0Car radio with navigation system and CD player 3.0Cassette radio with 2 loudspeakers 1.7CD radio 1.6Central hoovering system (Dometic) 5.4Dashboard made of precious root timber 0.5Duomatic L-Plus / Duo Comfort 2.0DVD Navigation system with return passage video system 6.1Exhauster hood 1.0Gel battery Exide Gel G 80 27.0Insulation mats for cockpit 0.5Light for tent in front of mobile home (Dometic) 0.2Loudspeakers (additional) in caravan) 1.7Microwave oven 15.0Motorisation 2.0 TDCi instead of 2.0 TDE (FORD) 10.0Navigation system Travel Pilot E1 2.0Oven 16.0Parking distance control system with optical warning 2.0
Radio, preparation for 1.3Remifront cockpit shade (plissé) 3.0Return passage video system with flat screen 2.0Satellite antenna, fully assembled (incl. 3 kg mast) 9.8Skylight, elec. 600 x 600 REMistar 10.8Solar system with 2 modules, each 50 W 16.0Solar system with 2 modules, each 75 W / 85 W 18.0Sun awning Omnistor, 300 x 250 cm 21.0Sun awning Omnistor, 350 x 250 cm 25.0TELECO digital satellit antenna w/ autom. search system 24.0Towbar coupling, rigid 15.5WAECO cruise control for FORD 1.5Water purification filter (Dometic) 3.0
FORD Flex Package: Air-conditioning system 20.0 Exterior mirror, electric 1.0 Window opener, electric 6.0 Wheel covers 6.0 Audio system 2000 5.0
Chassis03-7
1
2
Retracting leveling supports• Use crank to release leveing supports.• Retract leveling supports.• To lock leveling supports, press fork (1).
3.3 Leveling supportsLeveling supports, standard designThe leveling supports are located at the rear of your mobile home.
Swinging out the leveling supports• To swing out the leveling supports, press fork (1) and pull
towards hinge.• Swing out leveling supports.• If necessary, secure leveling supports from caving in.• Place leveling support upon base (2).• Use the crank to even out the leveling supports until the
vehicle is in a level position.
Chassis 03-8
1
The entrance step is automatically retracted when the
motor starts.Your mobile home has an electric entrance step (1).
Use the switch on the inside, next to the entrance door to activate it.
3.4 Entrance step
Do not step on the entrance step until it has been com-
pletely extended!
Mind the different heights of the steps and ensure that the
ground in front of the entrance is firm and level.
Chassis03-9
Registering accessories in the vehicle's documents
• Have your HOBBY dealer mount your externally mounted constructions.• Drive your mobile home to the Technical Surveyance Asso-
ciation (TÜV).• The TÜV will survey your externally mounted constructions
and draw up an appropriate expertise.• Take the expertise and the registration documents, Parts I
and II, to the Driver and Vehicle Licensing Agency. They will copy the changes into the vehicle's documents.
Do not forget that towbar couplings, motorcycle carriers,
leveling devices and/or additional spring blades must be
registered.
Please note that mounting additional equipment reduces
the load your mobile home can carry.
3.5 Externally mounted constructions
Chassis
Wheels, tires, brakes
Wheels, tires, brakes04-1
Driving to protect your tires
• Avoidbrakingsharplyandracingstarts.• Avoidlongdrivesonpoorroads.• Neverdriveanoverloadedvehicle.
TubelesstireshavebeenmountedonyourHOBBYmobile
home.Undernocircumstancesmaytubesbeinsertedin
thesetires!
Chapter 4: Wheels, tires, brakes
4.1 Wheels
Onyourfirstdrivewithyourmobilehome,pleasecheckthatyourtireboltsarestillsecurelytightenedafterhavingdriven50kmand,ifnecessary,tightenthemwithatorqueof160 Nm for 15" wheel rims (steel and light metal) and 180 Nm for 16" wheel rims (steel and light metal).Afterthis,thetireboltsshouldbecheckedregularlythattheyaresecurelytightened.
4.2 Tires
Useonlytiresthathavebeenenteredinthevehicle'sdocuments.Othertiresizesmayonlybeusediftheyhavebeenpermittedbythemanufacturerofthebasicvehicle.
Wheels, tires, brakes
1 2 3
04-2
4.3 Inflation pressure
Theinflationpressureofalltiresaswellasthesparetireshouldbecheckedapprox.every4weeksandbeforeyougoonlongerjourneys.The following applies when checking inflation pressure:• Checkthepressureonlywhenthetireiscold.• Ifcheckingorcorrecting thepressureofawarmtire, the
pressuremustbe0.3barhigherthanforacoldtire.
The following applies for inflation pressure:- correctinflationpressure(1).- inflationpressuretoolow(2).- inflationpressuretoohigh(3).
Ifthepressureistoolow,thismaycauseoverheatingofthe
tire,possiblyresultinginseveredamagetothetire.
Forthecorrectinflationpressure,pleaserefertothetablein
thechapteron“TechnicalData“ortheoperatinginstructions
forthebasicvehicle.
4.4 Tread depth
Replaceyourtiresassoonasthetreaddepthisonly1.6mm.
Tiresmaynotbeexchangedcrosswise,i.e.fromtherightsideofthevehicletotheleftandviceversa.
Tiresageeveniftheyareusedseldomornotatall.
Tire manufacturers‘ recommendations• Irrespectiveof their treaddepth, tiresshouldbechanged
every6years.• Avoidhardimpactsagainstcurbs,potholesorotherobsta-
cles.
Wheels, tires, brakes04-3
4.7 Spare tire
Asparetireisnotincludedinthescopeofdelivery.
4.6 Snow chains
Neverdrivefasterthan50km/h.
Donotusesnowchainsonsnow-freeroads.
Ornamentalhubcapsmustberemovedbeforeputtingon
snowchains.
4.6.1 Models with front-wheel driveIfyouwishtousesnowchains,thewheelsonthefrontaxlemustusetiressize195/75R16C(M+S)onsteelrims5.5Jx16H2,ET50.Youmayleavethetiressize215/75R16Contherearaxle.ThistiremixiscoveredbyFord'sbasicapprovaland,therefore,doesnotrequireextrapermission.
Tiressize195/75R16C(M+S)mustbeinflatedtothemaximumadmissiblepressureof4.8bar.Snowchainsmayonlybeusedwithsteelrimsandonlyonthefrontaxle.
Usesnowchainsonlyonthefrontaxle.
4.5 Wheel rimsUseonlythosewheelrimslistedinthevehicle‘sdocuments.Pleaseobservethefollowingpoints,shouldyouwishtouseotherwheelrims.
The following applies when using other wheel rims:- Size,- construction,- injectiondepthand- carryingpowermustbesufficientforthepermissibletotal
weight.- Theconeof the fasteningscrewmustcorrespond to the
constructionofthewheelrim.Adaptationsareonlypermittedifthesehavebeenreleasedbythemanufacturer.
Forexplicit information,pleaserefertotheGeneralType
Approval("AllgemeinenBetriebserlaubnis",ABE).
Aluminiumwheelrimsmustbetestedseparatelyforeachtypeof vehicle. The screwsusedonaluminium rimsmaynotbeusedforsteelrims.Whenusingaluminiumrims,tiresmaynotbechangedfromthefronttothebackorviceversa.
Wheels, tires, brakes 04-4
4.8 Repair kit
Donotusethetirerepairkitifthetirewasdamagedasaresultofdrivingwithoutair.Smallcuts,especiallyinthetiretread,canberesealedusingthetirerepairkit.Donotremoveforeignobjects(suchasscrewsornails)fromthetire.Thetirerepairkitcanbeusedaslongastheoutsidetemperatureis
approx.-30°Corhigher.
A Shakethebottle.Openthefillhose(1)onthebottle(foilsealistherebypunctured).
Wheels, tires, brakes
C Pullthestopper(4)fromthefillhose(1).Pushthefillhoseontothetirevalve.
D Holdthebottledownwiththefillingtubeandthenpressthemtogether.Presstheentirebottlecontentsintothetire.Pullthefillhoseoff(1)andscrewthevalveinsert(2)tightlyintothetirevalvewiththevalve-coreremover(3).
04-5
B Unscrewthevalvecapfromthetirevalve. Removethevalveinsert(2)withthevalvecoreremover(3). Donotlaythevalveinsert(2)downinsandordirt.
Wheels, tires, brakes
E Opentheairhose(5)onthetirevalve.Inserttheplug(6)intothecigarlightersocket.Thenpumpthetires(Fig.7).donotoperatetheelectricairpumplongerthan
8minutes!Dangerofoverheating!Ifsufficientairpres-sureisunattainable,drive10meters(eitherforwardorinreverse)sothatthesealantcanbeevenlydistributedwithinthetire.Repeatthepumpingprocess.Resumedrivingimmediately,sothatthesealantcanbeevenlydistributedwithinthetire.
Maximum speed: 80 km/h. Drive carefully, especially in curves.Checktirepressureafterdriving10minutes.Ifthetirepressurehasfallenunderthisminimumvalue(8),you
maynotdriveanyfurther. Iftheminimumvalueisstillindicated(8),correctthetire
pressureaccordingtothetirepressuretableinthegasbottlecontainer.Drivecarefullytothenearestmechanicandhavethetirereplaced.
Danger of accidents!Iftherequiredtirepressureis
stillunattainable,thetireistooseverelydamaged.In
thiscase,thetirerepairkitcannolongerprovideanef-
fectiveseal.Therefore,donotdriveanyfurther.Notifya
servicestationorthe24-hourservicehotline.
04-6
Wheels, tires, brakes04-7
4.9 Changing the tire
Furtherinformationisgivenintheoperatinginstructions
ofthemanufacturerofthebasicvehicle.
Danger of accidents!Havethetiresreplacedatthe
nearestservicestation.
F Adheretheprovidedstickertothecombinationinstru-mentwithinsightofthedriver.Disposeofusedtirerepairkitataservicestation.
Further information isgiven in theoperating instructions
fortheFordTransit.
4.10 Brakes
ThecomponentsinthebrakesystemarepartoftheGeneralTypeApproval(“AllgemeinenBetriebserlaubnis“,ABE).Ifyouchangethecomponentsinthebrakesystem,thetypeapprovalexpires.Anychangesareonlypossibleiftheyhavebeenreleasedbythemanufacturer.
Inyourowninterests,youshouldhavethebrakeschecked
regularlybyyourFiatorPeugeotrepairshop.
The following applies when maintaining the brake system:• Checkthelevelofbrakefluidregularly.• Checkthebrakesystemandbrakehosesregularlyforlea-
kage.Martensoftengnawatrubberhoses.• Useonlythosebrakeoilsthathavethesamefeaturesasthe
oilsthatarealreadyinthebrakecircuit.
Wheels, tires, brakes
Exterior Structure
Exterior Structure05-1
T555 FS Siesta 2007
T600 FC Siesta 2007 T600 GFS Siesta 2007
Storage flap (1)Toilet flap (2)
Gas box flap (3)
T600 GFLC Siesta 2007
Chapter 5: Exterior Structure
5.1 Overview of tank and service flaps
Exterior Structure 05-2
T650 GFLC Siesta 2007
T650 FLC Siesta 2007
Storage flap (1)Toilet flap (2)
Gas box flap (3)
Exterior Structure
1
2
05-3
RefrigeratorGrates supply the refrigerator with fresh air from outside to en-sure sufficient refrigerating capacity. The grate for fresh air intake (1) is on the outside wall of the vehicle. The grate for expelling used air (2) is above the grate for fresh air intake.
Danger! You can suffocate if the ventilation openings are
blocked! Never block ventilation openings.
Apply special covers when operating the mobile home in
winter. These covers can be purchased from your dealer.
5.2 Ventilation
The following applies for ventilation:Ventilation is important if you want to feel comfortable in your mobile home. No-draught ventilation has been integrated above the driving unit in your mobile home. The roof lights ensure ven-tilation. Never interfere with the way in which they operate.
Appropriate covers can be used to close the ventilation of the refrigerator, provided it does not run on gas.
Note the information given on the covers. They may only
be used when the refrigerator is operated electrically in
winter. For more information, please refer to the refrigerator
manufacturer‘s operating instructions.
Watery vapour is produced while cooking, from wet clothes,
etc. Every person transpires up to 35 g of water per hour.
Therefore, depending on the relative humidity, the windows
and skylight s must be opened for further ventilation (see
also “Operating in Winter“).
Exterior Structure
3
1
05-4
We recommend that you remove the ventilation grate if the
outside temperature is very high. This allows more air to
permeate to the refrigerator, intensifying refrigeration.
Removing the ventilation grate• Turn the screw (3) as far to the left as it will go.• Carefully pull out the ventilation grate, starting on the left.• Then remove the ventilation grate.
HeatingThe heating system is supplied with fresh air from outside (1). This ventilation flap also permits exhaust air from the system to escape.
Danger! You can suffocate if the ventilation openings are
blocked!
Never block ventilation openings.
Exterior Structure05-5
5.3 Opening and closing doors and flaps
Keys to the vehicleThe following keys are supplied with the motor home:- one master key- two keys for the following locks on the basic vehicle: - driver‘s door and passenger door
Note the manufacturer‘s operating instructions for the
basic vehicle.
- two keys that fit the following locks on the structure: - entrance door - service flaps - toilet flaps
In addition, a self-adhesive aluminium plate is supplied, en-
graved with the number of the key for the basic vehicle.
Entrance door
Opening• Use key to unlock door.• Pull on door handle.• Open door.
Closing• Close door.• Turn key until you hear the bolt lock into place.• Turn key back to verticle position and pull it out.
Exterior Structure 05-6
To avoid damaging the lock and the doorframe, the inner
door handle must be in a horizontal position and not slan-
ted upwards.
Remember that the entrance door is your escape route in an
emergency. Never barricade the door from the outside!
Luggage trunk flap
Opening• Use key to unlock flap.• Place your hand over the lock and give the flap a strong push
inwards.• Pull the flap upwards to open.
Closing• Pull the flap down to close.• Lock it with the key.
Exterior Structure05-7
21
1
2
3
Toilet flap
Opening• Use key to unlock flap (1).• Press both buttons (1 and 2) and open flap.
Closing• Press flap until it locks into place.• Use key to lock flap (1).
Exterior gas supply
At the customer‘s request, the mobile home can be fitted with an exterior gas supply (3). Equipment that uses gas, such as a gas grill or a gas lamp, can be supplied from outside the mobile home. The exterior gas supply is located below the gas box flap (2).
Opening• Pull the cover plate (1) of the flap towards you.
Closing• Press the cover plate (1) of the flap shut until you hear it lock
into place.
Exterior Structure
2
1
05-8
2
1
Fresh water filler neck
Opening• Use key to unlock (1).• Turn lid (2) firmly and remove.
Closing• Insert lid (2) and turn it closed.• Use key to lock (1).
Water supply for exterior shower
Opening• Slide cover flap (1) up to gain access to water supply.
Closing• Remove hose for exterior shower from branch neck (2) and
insert protective cap.• Slide cover flap down.
Exterior Structure05-9
1
2 5.5 Condensation in headlight systems
One of the problems often complained about is condensation on tthe outer glass of headlights or rear lights mde of clear glass. This appears after driving in the rain or on cold nights, and is a normal physical process. The expanding warm air is displaced through headlight vents from a lamp that has been turned on. After being turned off, the lamp slowly cools down and moist air from outside permeates inside through the vents. This moisture evaporates in the warm headlight and cools down to become condensation on the outer glass. This process is known as con-densation. After a short drive in dry weather or after the headlight has been on for a brief period a process of evaporation sets in which drys off the condensation. Technically speaking, this process is harmless, because the lamps are protected against any influences from condensation.
Exterior socket
Opening• Take hold of the bottom of the cover flap (1) and pull it up-
wards.
Closing• Remove CEE plug (2).• Push cover flap (1) down until you hear it lock into place.
5.4 Exterior mirror
Please refer to the operating instruction for the basic vehicle for information on how to adjust the exterior mirrors of your mobile home.
Exterior Structure
Electrical Installations
Electrical Installations06-1
Main elements of the electric system• "PC-100HB and PC-100HB T" CONTROL PANEL - controls the electric power consumers,• 12V DISTRIBUTON MODULE "DS-300HB" - main relay, battery parallel relay (12V - 70A), refrigerator
relay, pump relay, charging facility B1, safety fuses.• BATTERY LOADING DEVICE - loads the battery in buffer operation.• PROBE WITH ROD - measures contents of fresh water tank, 4-state visualisation• PROBE WITH SCREWS "SSP" - LED display shows when sewage tank is full• CONSUMER BATTERY "B2" - supplies all consumers• VEHICLE BATTERY "B1"• GENERATOR - loads both the vehicle and consumer batteries at the same
time• 230V MAIN SWITCH - supplies and protects the 230V consumers• 50A FUSES VEHICLE/ and CONSUMER BATTERIES
Chapter 6: Electrical Installations
6.1 Safety instructions
The following must be observed:• Do not remove the signs on electrical components giving
safety instructions or danger warnings.• Do not use the installation compartments for the caravan
battery, on-board control panel, battery charger and 230 V connector box as additional storage room.
• Smoking and open fire are forbidden when checking elec-trical equipment.
• Only authorised and experienced workshops may carry out electrical repairs.
• Inexpert handling of the vehicle‘s electrical system may endanger your own life as well as that of others.
• Use only weatherproof, 3-wired extension cable and shock-proof plug or CEE plug and coupler when hooking up to an external 230 V network.
6.2 HOBBY on-board control panelThe electric power supply is provided via the HOBBY on-board control panel in connection with an automatic battery charger.
Electrical Installations
• Should the consumer battery be removed, isolate the plus pole (to prevent short circuits when turning on the motor).
• If you are stopping in one place for a very long time, un-clamp the battery or recharge it regularly.
Battery charger• Install the battery charger in a dry and well-aired room.• This device may only be mounted by a professional.• In case of misuse, the guarantee and the manufacturer's
liability will no longer apply.• Do not carry out any maintenance work as along as the 230V
mains is still connected.• Never plug up the ventilation on the lid; ensure that there is
sufficient ventilation.• Turn off the switch before disconnecting the battery charger
from the 230V mains.
Tank probes• To avoid incrustations, especially in the sewage tank, never
let the water in the tanks stand for too long.
230V main switch• Before removing the lid, check that the plug for the electric
mains has been unplugged.
Advice and instructions
Important!• Any changes to the electrical installation may only be carried
out by a professional electrician.• Disconnect the battery and switch off the 230V mains before
carrying out any maintenance work.
Batteries• Please observe the battery manufacturer's operating in-
structions. • The acid in the battery is poisonous and corrosive. Avoid
contact with eyes and skin.• If the battery is completely empty, it must be recharged for
a minimum of 10 hours. If the battery has been empty for at least 8 weeks, it may be damaged.
• Check the amount of liquid in the batteries (acid batteries) regularly; gel batteries require no maintenance, but must continuously be recharged.
• Check the level of the battery fluid regularly (lead storage battery).
• Check that the clamps are still on properly and remove any layers of oxide.
• Unclamp the minus pole if the battery is not being used for a longer period of time (more than 1-2 months).
06-2
Electrical Installations
• To avoid damage to the module, ensure that the plugs are plugged in firmly.
• To switch off the power supply for the entire system, set the main switch 230 to "0" (OFF).
• Connect and disconnect the system to the 230V external mains only when the main switch is off.
• Should the switch be automatically interrupted, check the system for defects before switching the power supply back on.
Fuses• Only replace defect fuses after you have found the reason
for the defect and fixed it.• The new fuse must have the same amperage as the old
one.
Siesta control panel Description1) Button for monitoring fresh water tank.2) Button for monitoring consumer battery (B2).3) Button for monitoring vehicle battery (B1).4) LED signals test in fresh water tank; blinking signals emp-
ty tank.5) LEDs signal level of fresh water tank.6) LED signals test in sewage tank; blinking signals full tank.7) Blinking LED signals full sewage tank; LED 6 also signals
alarm.
06-3
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Electrical Installations 06-4
8) Signals that generator is charging vehicle and consumer batteries.
9) LED signals test of vehicle battery; blinking signals empty battery.
10) LED signals test of consumer battery; blinking signals empty battery.
11) LED signals that 230V mains is connected.12) LED voltmeter for monitoring voltage of vehicle and con-
sumer batteries.13) Control switch for sewage tank resistance; dependent on
main switch and functions when motor is switched on or 230V mains is connected.
14) Switch for water pump that operates pump relay; depen-dent on main switch.
15) Main switch for consumers; blinking LED signals that consumer battery is almost empty and protection against total discharge will soon be activated.
FunctionsProtection against total dischargeAn electronic installation turns off all 12V consumers when the consumer battery reaches a minimum voltage of 10V. The con-sumers can be switched on again for approx. one minute by switching the main switch on again.
The refrigerator, electric entrance step and those consumers directly supplied by B2 are not affected by this installation.
Electrical Installations06-5
12 V - Distribution panel
Hea
ting/
Boi
ler
Ligh
t B
Ligh
t A
Pum
p
Ent
ranc
e st
ep
Aux
.
Gas
con
sum
ers
Ref
riger
ator
D+
/Ext
erna
l lig
htin
g
Connection fresh water probe
Connection sewage probe
Connection battery charger1/8 free2/8 LED green3/8 LED red4/8 12V mains5/8 + charge6/8 Plus charge7/8 Earth8/8 Earth
Connection display panel
Connection earth consumers
Con
nect
ion
pum
p s
witc
h
Con
nect
ion
D+
gen
erat
or
Con
nect
ion
eart
h
Con
nect
ion
bat
tery
II
Con
nect
ion
bat
tery
I
Reserved for 9-pole plug
1/9 Heating/Boiler via main switch protected by fuse12/9, 5/9, 4/9 Light B via main relay protected by fuse23/9 Pump switched by relay protected by fuse46/9 External lighting / D+ increased automatic change-over via +, protected by fuse97/9, 8/9, 9/9 Light A via main relay protected by fuse3
Reserved for 6-pole plug
1/6 Entrance step continuous, protected by fuse52/6, 3/6 Refrigerator D+ controlled, protected by fuse84/6 Aux. continuous, protected by fuse65/6, 6/6 Gas consumers continuous, protected by fuse7
B2 permanently connected to refrigerator when connections KS1 and KS2 bypassed (no longer controlled via D+)
D+ signal switched via relay
Pump relay
Main relay
Parallel connection relay
Refrigera-tor relay
D+/Ext. lighting relay
KS2KS1
FWT
AWT
Display
Earth
Cha
rger
Pum
pD
+
Electrical Installations
1
2
3
4
5
6
7
8
06-6
Gas operation (heating and warm water)- Dial for room temperature (1) - green “operating“ control light (2)- summer operation (water temperature 40°C or 60°C (3)- winter operation (heating without need for warm water) (4) - winter operation (heating with need for warm water) (5) - rotary switch “off“ (6)- yellow control light: “boiler in heating phase“ (7)- red control light: “malfunction“ (8)
For further information, please refer to the enclosed TRUMA
operating manual.
6.3 Electric power supply
Your mobile home has the following connections for electric power supply:- electric mains (a.c. voltage 230 V)- caravan battery (d.c. voltage 12 V)
Electric power supply from the electric mainsThe 230 V system is protected by a 2-pole circuit breaker with 16 A. The circuit breaker is located behind the driver‘s seat.Should there be a malfunction, the passenger circuit breaker opens the entire 230 V circuit. In most cases, such a malfunction is caused by a defect piece of electric equipment or a defect in its supply line.• Repair the defect before switching the circuit breaker on
again.• If the defect cannot be repaired, consult an experienced
electrician.
Electrical Installations06-7
Position of the battery chargerThe battery charger is located in the driver's seat.
Operating with 230 V electric mainsAfter switching on the master switch on the HOBBY on-board control panel, the caravan battery will be charged by the battery charger in the mobile home.
Fresh water
Electric mains 230 V
The following applies for the electric mains:• the power supply lead may not be longer than 25 m.
If you are using a cable drum without protection against
overheating, the electric cable must be completely unwound
from the cable drum.
• Use only plugs and cables that meet CEE standards.• First, make the connection to the main socket (1) of the
vehicle.• Then insert the other plug in the live socket.• Follow this sequence in reverse when you pull out the
plug.
6.4 Function of the power generating unit
Charging procedureThe charging procedure is dependent on the battery voltage of the caravan battery:- Charge until the battery voltage has reached 14.4 V.- Switch off the battery charger until the battery voltage has
sunk to 13.8 V.- Recharge when the battery voltage sinks below 13.8 V.- Make a parallel connection and charge the engine battery as
well as the caravan battery when the battery voltage sinks below 13.5 V.
– Separate the engine battery and the caravan battery when the joint battery voltage sinks below 12.5 V.
Electrical Installations 06-8
The battery voltage of both the engine battery and the cara-
van battery can be checked continuously on the on-board
control panel located above the entrance door.
The battery charger only works if the batteries have been
inserted with their poles in the right direction.
A discharged caravan requires a charging period of approx.
12 hours on the electric mains to completely recharge itself.
This charging period must be extended accordingly if equip-
ment that uses 12 V is switched on at the same time.
Protection against total dischargeIf the battery voltage of the caravan battery sinks below 10.5 V, a relay shuts down all the equipment that uses voltage.
If the protection against total discharge takes effect, turn
off the 12 V master switch to avoid an additional discharge
of the caravan battery.
Function of the battery charger
Protecting the deviceIf the battery charger should become hot because of high en-vironmental temperatures or high charging currents, a built-in thermal switch turns off the battery charger until the temperature in the battery charger has dropped again.
Checklist• Turn off the motor.• Turn off the mains switch on the battery charger.• Connect the battery charger to the mains supply.• Switch on the 12 V master switch.• Turn off all equipment (except refrigerator) that uses 12 V.• Turn on the mains switch on the battery charger.
The voltage of the caravan battery must rise to a maximum voltage of 14.4 V.
If this does not happen after using the built-in battery charger to charge the battery, check the following:• Has the battery charger been properly attached to the net-
work?• Is the mains fuse of the battery charger functioning proper-
ly?
Electrical Installations06-9
Operation when the motor is runningAs soon as the motor is running, a relay connects the starter battery and the caravan battery in parallel. The D+ signal sits close to the dynamo. Therefore, the dynamo charges both batteries. If the D+ signal no longer sits close to the dynamo, the two batteries will be separated from each other again. In this way, the starter battery cannot be discharged by equipment in the caravan.The 12 V supply for the refrigerator only functions when you are driving. If the motor has stopped, the 12 V operation of the refrigerator is automatically turned off again.
To charge a discharged caravan battery optimally while
driving, disconnect the 12 V operation of the refrigerator and
turn off as much equipment as possible that uses 12 V.
Checklist• Turn off the motor.• Switch on the 12 V master switch.• Turn off all equipment that uses 12 V.• Start the motor.
• Is the battery voltage of the battery charger above 1 volt?• Have the poles of the caravan battery been attached pro-
perly?• Is the connection between the battery charger and the on-
board control panel functioning properly?
The voltage of the caravan battery must rise if- the engine speed is above the idling speed,- the vehicle‘s battery is not completely discharged.
If this does not happen after using the dynamo to charge the battery, check the following:
• Is the fuse in the supply line to the vehicle‘s battery functio-ning properly near the vehicle‘s battery?
• Have the poles of the caravan battery been attached properly to the battery charger?
• Is the fuse in the supply line to the “D+“ signal functioning properly near the vehicle‘s battery?
• Is the “D+“ signal sitting close to the battery charger? There must be a voltage of 12 V here when the motor is running.
• Is the connection between the battery charger and the on-board control panel functioning properly?
Operation by means of a 12 V caravan batteryAll of the equipment is automatically supplied from the caravan battery if the mobile home is standing still without a 230 V mains supply and with its engine turned off. The 12 V master switch must be switched on.
Electrical Installations 06-10
The caravan battery should only be allowed to discharge to
a voltage of 11 V. At this point, you should ensure that it is
recharged from the dynamo or from public supply.
6.5 Caravan battery
Location- Under the driver's seat, in the double bottom or in a separate
compartment that is externally accessible, depending on the
floor plan.
Features- The battery does not require maintenance. It does not need
to be refilled with water.- The battery is closed off and cannot leak.- The battery is cycle-proof, making it especially suitable
for the supply of the board network. Several discharging/charging operations are possible.
Use only the same kind of batteries when exchanging the
battery (same capacity and voltage, cycle-proof, mainte-
nance-free and leakproof).
Changing the battery
• Please do not smoke when changing the battery.• Disconnect the connection to the 230 V network.• First, disconnect the minus (-) connector.• Then disconnect the plus (+) connector.• Remove the battery.• Insert the new battery.• Use the reverse sequence to connect the new battery.
The solution of electrolytes contained in the battery is poi-
sonous and corrosive! Protect your eyes and face whenever
handling the battery.
If your skin or eyes come into contact with this solution,
wash immediately with lots of clear water.
Keep open flames or equipment that gives off sparks away
from the battery. Danger! Explosive!
Electrical Installations06-11
1
1
6.6 Fuse protection of the electric system
Starter batteryThe main fuse protection is carried out by a 40 A safety fuse (1). The fuse is located under the hood next to the starter battery.
Caravan batteryThe main fuse protection is carried out by a 30 A safety fuse (1). The fuse is located right next to the battery.
12 V circuitsThese are protected by overload releases on the HOBBY con-trol panel.
Information on fuses15 A: refrigerator10 A: light10 A: pump, boiler, heating, TV
Electrical Installations 06-12
The following applies if one of the devices breaks down:• Check the fuse on the corresponding electric circuit.• Press the operating button.• If the fuse goes off again, please speak to your authorised
Hobby dealer.
Charger with fuse box• The charger with separate fuse box is located under the
passenger seat.
Electrical Installations06-13
6.7 Interior circuit diagramT555 AK-LC/T555 AK-SC
Electrical Installations 06-14
T555 AK-LC/ T555 AK-SC
Electrical Installations06-15
T555 FS u. AK
Electrical Installations 06-16
T555 FS u. AK
Electrical Installations06-17
T600 FC
Electrical Installations 06-18
T600 FC
Electrical Installations06-19
T600 GFLC-AK
Electrical Installations 06-20
T600 GFLC-AK
Electrical Installations06-21
T600 GFS
Electrical Installations 06-22
T600 GFS
Electrical Installations06-23
T650 AK-KLC
Electrical Installations 06-24
T650 AK-KLC
Electrical Installations06-25
T650 FLC u. AK
Electrical Installations 06-26
T650 FLC u. AK
Electrical Installations06-27
T650 GFLC u. AK
Electrical Installations 06-28
T650 GFLC u. AK
Electrical Installations
6.8 Subsequently installed devices
Subsequently installed electronic devices that can be used while driving (e.g. mobile phones, wireless equipment, radios, came-ras for driving in reverse, navigation equipment, or others) must meet all of the requirements for electromagnetic compatibility. Such equipment must have been approved in accordance with EU Guideline 72/245/EWG as it appears in version 95/54/EG, because otherwise it may cause interference with the electronic systems already installed in the mobile home.
A CE mark is mandatory for devices that have been subsequent-ly installed and which cannot be used while driving.
06-29
Electrical Installations
Electrical Installations
Electrical Installations06-1
Main elements of the electric system• "PC-100HB and PC-100HB T" CONTROL PANEL - controls the electric power consumers,• 12V DISTRIBUTON MODULE "DS-300HB" - main relay, battery parallel relay (12V - 70A), refrigerator
relay, pump relay, charging facility B1, safety fuses.• BATTERY LOADING DEVICE - loads the battery in buffer operation.• PROBE WITH ROD - measures contents of fresh water tank, 4-state visualisation• PROBE WITH SCREWS "SSP" - LED display shows when sewage tank is full• CONSUMER BATTERY "B2" - supplies all consumers• VEHICLE BATTERY "B1"• GENERATOR - loads both the vehicle and consumer batteries at the same
time• 230V MAIN SWITCH - supplies and protects the 230V consumers• 50A FUSES VEHICLE/ and CONSUMER BATTERIES
Chapter 6: Electrical Installations
6.1 Safety instructions
The following must be observed:• Do not remove the signs on electrical components giving
safety instructions or danger warnings.• Do not use the installation compartments for the caravan
battery, on-board control panel, battery charger and 230 V connector box as additional storage room.
• Smoking and open fire are forbidden when checking elec-trical equipment.
• Only authorised and experienced workshops may carry out electrical repairs.
• Inexpert handling of the vehicle‘s electrical system may endanger your own life as well as that of others.
• Use only weatherproof, 3-wired extension cable and shock-proof plug or CEE plug and coupler when hooking up to an external 230 V network.
6.2 HOBBY on-board control panelThe electric power supply is provided via the HOBBY on-board control panel in connection with an automatic battery charger.
Electrical Installations
• Should the consumer battery be removed, isolate the plus pole (to prevent short circuits when turning on the motor).
• If you are stopping in one place for a very long time, un-clamp the battery or recharge it regularly.
Battery charger• Install the battery charger in a dry and well-aired room.• This device may only be mounted by a professional.• In case of misuse, the guarantee and the manufacturer's
liability will no longer apply.• Do not carry out any maintenance work as along as the 230V
mains is still connected.• Never plug up the ventilation on the lid; ensure that there is
sufficient ventilation.• Turn off the switch before disconnecting the battery charger
from the 230V mains.
Tank probes• To avoid incrustations, especially in the sewage tank, never
let the water in the tanks stand for too long.
230V main switch• Before removing the lid, check that the plug for the electric
mains has been unplugged.
Advice and instructions
Important!• Any changes to the electrical installation may only be carried
out by a professional electrician.• Disconnect the battery and switch off the 230V mains before
carrying out any maintenance work.
Batteries• Please observe the battery manufacturer's operating in-
structions. • The acid in the battery is poisonous and corrosive. Avoid
contact with eyes and skin.• If the battery is completely empty, it must be recharged for
a minimum of 10 hours. If the battery has been empty for at least 8 weeks, it may be damaged.
• Check the amount of liquid in the batteries (acid batteries) regularly; gel batteries require no maintenance, but must continuously be recharged.
• Check the level of the battery fluid regularly (lead storage battery).
• Check that the clamps are still on properly and remove any layers of oxide.
• Unclamp the minus pole if the battery is not being used for a longer period of time (more than 1-2 months).
06-2
Electrical Installations
• To avoid damage to the module, ensure that the plugs are plugged in firmly.
• To switch off the power supply for the entire system, set the main switch 230 to "0" (OFF).
• Connect and disconnect the system to the 230V external mains only when the main switch is off.
• Should the switch be automatically interrupted, check the system for defects before switching the power supply back on.
Fuses• Only replace defect fuses after you have found the reason
for the defect and fixed it.• The new fuse must have the same amperage as the old
one.
Siesta control panel Description1) Button for monitoring fresh water tank.2) Button for monitoring consumer battery (B2).3) Button for monitoring vehicle battery (B1).4) LED signals test in fresh water tank; blinking signals emp-
ty tank.5) LEDs signal level of fresh water tank.6) LED signals test in sewage tank; blinking signals full tank.7) Blinking LED signals full sewage tank; LED 6 also signals
alarm.
06-3
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Electrical Installations 06-4
8) Signals that generator is charging vehicle and consumer batteries.
9) LED signals test of vehicle battery; blinking signals empty battery.
10) LED signals test of consumer battery; blinking signals empty battery.
11) LED signals that 230V mains is connected.12) LED voltmeter for monitoring voltage of vehicle and con-
sumer batteries.13) Control switch for sewage tank resistance; dependent on
main switch and functions when motor is switched on or 230V mains is connected.
14) Switch for water pump that operates pump relay; depen-dent on main switch.
15) Main switch for consumers; blinking LED signals that consumer battery is almost empty and protection against total discharge will soon be activated.
FunctionsProtection against total dischargeAn electronic installation turns off all 12V consumers when the consumer battery reaches a minimum voltage of 10V. The con-sumers can be switched on again for approx. one minute by switching the main switch on again.
The refrigerator, electric entrance step and those consumers directly supplied by B2 are not affected by this installation.
Electrical Installations06-5
12 V - Distribution panel
Hea
ting/
Boi
ler
Ligh
t B
Ligh
t A
Pum
p
Ent
ranc
e st
ep
Aux
.
Gas
con
sum
ers
Ref
riger
ator
D+
/Ext
erna
l lig
htin
g
Connection fresh water probe
Connection sewage probe
Connection battery charger1/8 free2/8 LED green3/8 LED red4/8 12V mains5/8 + charge6/8 Plus charge7/8 Earth8/8 Earth
Connection display panel
Connection earth consumers
Con
nect
ion
pum
p s
witc
h
Con
nect
ion
D+
gen
erat
or
Con
nect
ion
eart
h
Con
nect
ion
bat
tery
II
Con
nect
ion
bat
tery
I
Reserved for 9-pole plug
1/9 Heating/Boiler via main switch protected by fuse12/9, 5/9, 4/9 Light B via main relay protected by fuse23/9 Pump switched by relay protected by fuse46/9 External lighting / D+ increased automatic change-over via +, protected by fuse97/9, 8/9, 9/9 Light A via main relay protected by fuse3
Reserved for 6-pole plug
1/6 Entrance step continuous, protected by fuse52/6, 3/6 Refrigerator D+ controlled, protected by fuse84/6 Aux. continuous, protected by fuse65/6, 6/6 Gas consumers continuous, protected by fuse7
B2 permanently connected to refrigerator when connections KS1 and KS2 bypassed (no longer controlled via D+)
D+ signal switched via relay
Pump relay
Main relay
Parallel connection relay
Refrigera-tor relay
D+/Ext. lighting relay
KS2KS1
FWT
AWT
Display
Earth
Cha
rger
Pum
pD
+
Electrical Installations
1
2
3
4
5
6
7
8
06-6
Gas operation (heating and warm water)- Dial for room temperature (1) - green “operating“ control light (2)- summer operation (water temperature 40°C or 60°C (3)- winter operation (heating without need for warm water) (4) - winter operation (heating with need for warm water) (5) - rotary switch “off“ (6)- yellow control light: “boiler in heating phase“ (7)- red control light: “malfunction“ (8)
For further information, please refer to the enclosed TRUMA
operating manual.
6.3 Electric power supply
Your mobile home has the following connections for electric power supply:- electric mains (a.c. voltage 230 V)- caravan battery (d.c. voltage 12 V)
Electric power supply from the electric mainsThe 230 V system is protected by a 2-pole circuit breaker with 16 A. The circuit breaker is located behind the driver‘s seat.Should there be a malfunction, the passenger circuit breaker opens the entire 230 V circuit. In most cases, such a malfunction is caused by a defect piece of electric equipment or a defect in its supply line.• Repair the defect before switching the circuit breaker on
again.• If the defect cannot be repaired, consult an experienced
electrician.
Electrical Installations06-7
Position of the battery chargerThe battery charger is located in the driver's seat.
Operating with 230 V electric mainsAfter switching on the master switch on the HOBBY on-board control panel, the caravan battery will be charged by the battery charger in the mobile home.
Fresh water
Electric mains 230 V
The following applies for the electric mains:• the power supply lead may not be longer than 25 m.
If you are using a cable drum without protection against
overheating, the electric cable must be completely unwound
from the cable drum.
• Use only plugs and cables that meet CEE standards.• First, make the connection to the main socket (1) of the
vehicle.• Then insert the other plug in the live socket.• Follow this sequence in reverse when you pull out the
plug.
6.4 Function of the power generating unit
Charging procedureThe charging procedure is dependent on the battery voltage of the caravan battery:- Charge until the battery voltage has reached 14.4 V.- Switch off the battery charger until the battery voltage has
sunk to 13.8 V.- Recharge when the battery voltage sinks below 13.8 V.- Make a parallel connection and charge the engine battery as
well as the caravan battery when the battery voltage sinks below 13.5 V.
– Separate the engine battery and the caravan battery when the joint battery voltage sinks below 12.5 V.
Electrical Installations 06-8
The battery voltage of both the engine battery and the cara-
van battery can be checked continuously on the on-board
control panel located above the entrance door.
The battery charger only works if the batteries have been
inserted with their poles in the right direction.
A discharged caravan requires a charging period of approx.
12 hours on the electric mains to completely recharge itself.
This charging period must be extended accordingly if equip-
ment that uses 12 V is switched on at the same time.
Protection against total dischargeIf the battery voltage of the caravan battery sinks below 10.5 V, a relay shuts down all the equipment that uses voltage.
If the protection against total discharge takes effect, turn
off the 12 V master switch to avoid an additional discharge
of the caravan battery.
Function of the battery charger
Protecting the deviceIf the battery charger should become hot because of high en-vironmental temperatures or high charging currents, a built-in thermal switch turns off the battery charger until the temperature in the battery charger has dropped again.
Checklist• Turn off the motor.• Turn off the mains switch on the battery charger.• Connect the battery charger to the mains supply.• Switch on the 12 V master switch.• Turn off all equipment (except refrigerator) that uses 12 V.• Turn on the mains switch on the battery charger.
The voltage of the caravan battery must rise to a maximum voltage of 14.4 V.
If this does not happen after using the built-in battery charger to charge the battery, check the following:• Has the battery charger been properly attached to the net-
work?• Is the mains fuse of the battery charger functioning proper-
ly?
Electrical Installations06-9
Operation when the motor is runningAs soon as the motor is running, a relay connects the starter battery and the caravan battery in parallel. The D+ signal sits close to the dynamo. Therefore, the dynamo charges both batteries. If the D+ signal no longer sits close to the dynamo, the two batteries will be separated from each other again. In this way, the starter battery cannot be discharged by equipment in the caravan.The 12 V supply for the refrigerator only functions when you are driving. If the motor has stopped, the 12 V operation of the refrigerator is automatically turned off again.
To charge a discharged caravan battery optimally while
driving, disconnect the 12 V operation of the refrigerator and
turn off as much equipment as possible that uses 12 V.
Checklist• Turn off the motor.• Switch on the 12 V master switch.• Turn off all equipment that uses 12 V.• Start the motor.
• Is the battery voltage of the battery charger above 1 volt?• Have the poles of the caravan battery been attached pro-
perly?• Is the connection between the battery charger and the on-
board control panel functioning properly?
The voltage of the caravan battery must rise if- the engine speed is above the idling speed,- the vehicle‘s battery is not completely discharged.
If this does not happen after using the dynamo to charge the battery, check the following:
• Is the fuse in the supply line to the vehicle‘s battery functio-ning properly near the vehicle‘s battery?
• Have the poles of the caravan battery been attached properly to the battery charger?
• Is the fuse in the supply line to the “D+“ signal functioning properly near the vehicle‘s battery?
• Is the “D+“ signal sitting close to the battery charger? There must be a voltage of 12 V here when the motor is running.
• Is the connection between the battery charger and the on-board control panel functioning properly?
Operation by means of a 12 V caravan batteryAll of the equipment is automatically supplied from the caravan battery if the mobile home is standing still without a 230 V mains supply and with its engine turned off. The 12 V master switch must be switched on.
Electrical Installations 06-10
The caravan battery should only be allowed to discharge to
a voltage of 11 V. At this point, you should ensure that it is
recharged from the dynamo or from public supply.
6.5 Caravan battery
Location- Under the driver's seat, in the double bottom or in a separate
compartment that is externally accessible, depending on the
floor plan.
Features- The battery does not require maintenance. It does not need
to be refilled with water.- The battery is closed off and cannot leak.- The battery is cycle-proof, making it especially suitable
for the supply of the board network. Several discharging/charging operations are possible.
Use only the same kind of batteries when exchanging the
battery (same capacity and voltage, cycle-proof, mainte-
nance-free and leakproof).
Changing the battery
• Please do not smoke when changing the battery.• Disconnect the connection to the 230 V network.• First, disconnect the minus (-) connector.• Then disconnect the plus (+) connector.• Remove the battery.• Insert the new battery.• Use the reverse sequence to connect the new battery.
The solution of electrolytes contained in the battery is poi-
sonous and corrosive! Protect your eyes and face whenever
handling the battery.
If your skin or eyes come into contact with this solution,
wash immediately with lots of clear water.
Keep open flames or equipment that gives off sparks away
from the battery. Danger! Explosive!
Electrical Installations06-11
1
1
6.6 Fuse protection of the electric system
Starter batteryThe main fuse protection is carried out by a 40 A safety fuse (1). The fuse is located under the hood next to the starter battery.
Caravan batteryThe main fuse protection is carried out by a 30 A safety fuse (1). The fuse is located right next to the battery.
12 V circuitsThese are protected by overload releases on the HOBBY con-trol panel.
Information on fuses15 A: refrigerator10 A: light10 A: pump, boiler, heating, TV
Electrical Installations 06-12
The following applies if one of the devices breaks down:• Check the fuse on the corresponding electric circuit.• Press the operating button.• If the fuse goes off again, please speak to your authorised
Hobby dealer.
Charger with fuse box• The charger with separate fuse box is located under the
passenger seat.
Electrical Installations06-13
6.7 Interior circuit diagramT555 AK-LC/T555 AK-SC
Electrical Installations 06-14
T555 AK-LC/ T555 AK-SC
Electrical Installations06-15
T555 FS u. AK
Electrical Installations 06-16
T555 FS u. AK
Electrical Installations06-17
T600 FC
Electrical Installations 06-18
T600 FC
Electrical Installations06-19
T600 GFLC-AK
Electrical Installations 06-20
T600 GFLC-AK
Electrical Installations06-21
T600 GFS
Electrical Installations 06-22
T600 GFS
Electrical Installations06-23
T650 AK-KLC
Electrical Installations 06-24
T650 AK-KLC
Electrical Installations06-25
T650 FLC u. AK
Electrical Installations 06-26
T650 FLC u. AK
Electrical Installations06-27
T650 GFLC u. AK
Electrical Installations 06-28
T650 GFLC u. AK
Electrical Installations
6.8 Subsequently installed devices
Subsequently installed electronic devices that can be used while driving (e.g. mobile phones, wireless equipment, radios, came-ras for driving in reverse, navigation equipment, or others) must meet all of the requirements for electromagnetic compatibility. Such equipment must have been approved in accordance with EU Guideline 72/245/EWG as it appears in version 95/54/EG, because otherwise it may cause interference with the electronic systems already installed in the mobile home.
A CE mark is mandatory for devices that have been subsequent-ly installed and which cannot be used while driving.
06-29
Electrical Installations
Water
Water
1
08-1
8.1 Water supply
Warm water supplyThe kitchen and toilet are supplied with fresh water by means of a water pump. The pump is located close to the heating system.
Putting the submerged pump into operation• Switchonthe12Vmasterswitch.• Switchonthewatersupplyswitch,locatedontheon-board
control panel.
Always ensure that the freshwater tank is filledbefore
switching on the pump. The pump can be destroyed if the
tank is dry!
Chapter 8: Water
Fresh water tank
To fill with water• Closealloutletsandvalves.• Unlockandopenfillerneck(1).• Fill tankwithdrinkingwater,preferablyusingahose (not
includedinscopeofdelivery).
To draw water• Switchon12Vmasterswitch.• Turnswitchesforwaterpump,heatingandboilerto“ON“.• Turnon“hot“or“cold“watertaps.
Water 08-2
Emptying the fresh water tank
• Valvesarelocatednexttothefreshwatertankintheseatingarrangement by the outside wall.
During the cold season or if the main switch is turned on
while theheatingsystem isoff, theTRUMAsafetyvalve
opens,allowingtheboilertoemptyitself.
Water08-3
The following applies for obtaining good water from the tank:• Onlyfillthetankwithdrinkingwater.Whenfilling,payatten-
tiontothestickerwiththe“FreshWater“symbol.• Alwaysboilwaterbeforeusingit.• Lockthetank.• Emptythewatertankaftereveryjourneyandbeforeletting
your mobile home stand for a longer period of time.• Cleanthewatertankthoroughlywithwater.
Waterinclosedcontainers,suchasatank,quicklybecomes
fullofbacteria.Ifyouenjoydrinkingplainwater,youshould
add a disinfectant or store mineral water.
Neverallowantifreezerorotherchemicalstogetintothe
watercircuit.Thiscanbepoisonous!Whenoperatinginwin-
ter,ensurethatthefreshwatertankissufficientlyheated.
Sewage tank
Emptying the sewage tank• Thesupportforemptyingthesewagetankislocatedunder-
neath the mobile home. Pull the slide and let the sewage
run off at a sewage disposal place.• Afterthesewagehasrunoffcompletely,pushtheslideback
into place.
Onlyemptyyoursewagetankinspecialplacesforsewage
disposal, but never in open spaces!Generally, sewage
stationsarefoundinmotorwayserviceareas,campsites
or petrol stations.
Water 08-4
8.2 Flushing toilet
Preparing the toilet• OpentheThetforddoorandpulltheholdingbaruptoremove
theexcrementtank.
Theexcrementtankcanonlyberemovedwhenthebolt
is closed.
• Pulloutthetankasfaraspossible,keepingitlevel.• Slightlytiptheexcrementtankandthenpullitoutcomple-
tely.• Placeitinanuprightverticalposition.
Youmaybeable toavoid theuseofsanitary liquidsby
installing an activated carbon filter system (sold as an
accessory)!
Usesanitaryliquidsverysparingly.Anoverdoseisnogu-
aranteeofpreventingodours!
• Filltheexcrementtankwiththecorrectamountofsanitaryliquid.
• Thenaddenoughwatertocompletelycoverthebottomoftheexcrementtank.
• Returntheemptyingsupporttoitsoriginalposition.• Turntheemptyingsupporttoanupwardposition.
Water08-5
• Pushtheexcrementtankbackintoposition.• Ensurethattheholdingbarsecurestheexcrementtank.• Closetheserviceflap.
Neverfillsanitaryliquiddirectlyintothetoiletbowl.Using the toilet• Turnthetoiletbowltoacomfortableposition.• Usethetoilet.• Fillthetoiletbowlwithwater.Presstheflushbutton.Flushing
will continue for as long as you press the button.
Water 08-6
C200 S Cassette• Opentheboltbyturningtheboltlevercounter-clockwise.• Flushthetoiletbypressingtheflushbutton.• Afterflushing,closethebolt.
Water08-7
Emptying the cassette• OpentheThetforddoorandpulltheholdingbaruptoremove
theexcrementtank.
Theexcrementtankcanonlyberemovedwhenthebolt
is closed.
• Pulloutthetankasfaraspossible,keepingitlevel.• Slightlytipthetankandthenpullitoutcompletely.
Empty theexcrement tank inspecialplaces forsanitary
disposal,butneverinopenspaces!
• Taketheexcrementtanktoasanitarydisposalplace,makingsure to hold the emptying support in an upright position.
• Removethecapontheemptyingsupport.• Place the emptying support on the excrement tank in a
downward position.• Presstheaeratingbuttonwithyourthumb.Theexcrement
tank will empty itself.• Returntheexcrementtanktoitsstorageposition,pushing
it in until the holding bar locks it into place.• Locktheserviceflap.
Water 08-8
The following applies for an environmentally-friendly use of the toilet:• Fillthetankonlywithtoiletsolutionsthathavebeenapproved
anddonotpollutetheenvironment!• Emptythetoiletonlyintotheappropriateoutletsoratservice
stations!• Neveremptysewageintoadrain!Drainchannelsgenerally
bypassclarificationplantsandenddirectlyinariver.
Water08-9
• Onlyshutthetapswhentheboilerisfull,thedisplacedairhasescapedandwaterisflowingfromthehotwatertaps.
For further information,please refer to theTRUMAope-
rating manual.
8.3 Hot water supply
Water heaterYourmobilehomeisequippedwithaliquidgasheatingsystemwith an integrated boiler. The boiler holds 14 liters of water.Theoperatingdeviceforthewaterheaterisintegratedinthepanel for the heating system.
The following applies for the water heater:• Emptythewaterifthereisdangeroffrost!• Ifthewaterheaterhasbeenunusedforalongerperiodof
time,rinseitout(openthemixingtap)!
Onlyallowexpertstocarryoutrepairs!
Any changes to the boiler lead to breakdowns and the type
approvalforthedevicewillbeterminated!
Filling the water heater (initial operation or after emp-tying)• Turnon thewaterpumpby turningon theswitch for the
electriccircuitforthewaterpump,locatedonthedisplayand operating panel.
• Openallofthehotwatertaps.
Water
31
7
8
2
6
4
5
31
7
8
2
6
4
5
08-10
Operating in summer - hot water only• Turntherotaryswitch(6)tosummeroperation(3),40°Cor
60°C.
• Afterthesetwatertemperature(40°Cor60°C)hasbeenre-
ached,theburnerturnsitselfoffandtheyellowcontrollight
(7)turnsoff.
Operating in winter - heating without a demand for hot water• Turntherotaryswitch(1)tothedesiredsettingonthether-
mostat(1-9).Afterbeingswitchedon,thegreencontrollight(2)turnsonandshowstheroomtemperaturethathasbeenset.
• Turntherotaryswitchtotheoperatingposition(4).
Thedevicewillautomaticallyselecttherequiredlevelofper-formance depending on the difference in temperature between the set temperature and the temperature at present in the room. Afterreachingthetemperaturesetontheoperatingdevice,theburnershiftsdowntothelowestlevelandheatsthewaterto60°C. the yellowcontrol light (7) shows theheatingphase,turning off when the temperature has been reached.
Water
31
7
8
2
6
4
5
08-11
Operating in winter - heating with a demand for hot water• Turntherotaryswitch(1)tothedesiredsettingonthether-
mostat(1-9).Afterbeingswitchedon,thegreencontrollight(2)turnsonandshowstheroomtemperaturethathasbeenset.
• Turntherotaryswitchtotheoperatingposition(5).
Thedevicewillautomaticallyselecttherequiredlevelofper-formance depending on the difference in temperature between the set temperature and the temperature at present in the room. Afterreachingthetemperaturesetontheoperatingdevice,theheatingturnsitselfoff(irrespectiveofthewatertemperature).
Thewaterisautomaticallyheatediftheboilerhasbeenfilled.
The water temperature then depends on the heating capacity thathasbeensetandthetimerequiredtoheattheroomuntilthe set temperature has been reached.
Inthisoperatingposition,theyellowcontrollight(6)onlylightsupifthewatertemperaturedropsbelow5°C.
Itisalwayspossibletooperatetheheatingsystem,either
with or without water.
Turning off “Gas Operation“• Usetherotaryswitch(6)toturnofftheheating.
The water must be emptied if there is danger of frost!
If thedevicehasnotbeenused fora longerperiodof time,close thequick-actionstopvalve in thegassupply lineandthe gas bottle.
Water
31
7
8
2
6
4
5
08-12
Malfunction• Incaseofmalfunction,theredcontrollight(8)lightsup.• Forpossiblecauses,pleaserefertotheTRUMAOperating
Manualforinstructionsonfindingdefects.• Tounlock,turnoffandthenonagain.
Emptying the boiler• Turnoff thewaterpumpby turningoff theswitch for the
electriccircuitforthewaterpump,locatedonthedisplayand operating panel.
• Openallthehotwatertaps.• Press the control button (6) on the electrical safety/drain
valve.Thecontentsoftheboilerarenowdirectlyemptiedoutside.
Iftheheatingisnoton,thesafety/drainvalvecanonlybe
closedwhenthetemperatureisabove8°C.
If thetemperatureofthesafety/drainvalve is lowerthan
2°C, the contents of theboiler candrain offwhen the
deviceisturnedoff.
Gas
Gas09-1
Chapter 9: Gas
9.1 General safety rules for the use of LPG fittings
Checking the gas fittings• Beforeinitialoperation,havetheLPGfittingscheckedbyan
expert.• Thegasfittingsmustbecheckedevery2yearsbyanLPG
expert.Thismustbeconfirmedonthecertificate(conformwithFormG607fromtheGermanAssociationofGasandWaterExperts).
• Theregulatorandwastegaspipesmustalsobechecked.• Werecommendthatyoureplacethesafetyregulatoratleast
every6years.• Theconnectinghoseshouldalsobecheckedregularlyfor
damage.Replace it immediately if youfind tears,porousspotsorsimilardamage.
• Theoperatorisresponsibleforhavingcheckscarriedout.
Ifyoususpectthatgasisleaking,takethefollowingmea-
suresimmediately:
•Shutthestopvalveonthegasbottle.
•Ignitionsourcessuchasopenfireorsmokingare
strictlyforbidden.
•Airtherooms.
•Clearthedangerzone.
•Informyoursurroundings(groundsman)and,ifneces-
sary,thefiredepartment.
Thegasfittingsmayonlybetakenintooperationagain
aftertheyhavebeencheckedbyanexpert.
Built-in objects and changes• Onlyanexpertmaybuildinobjectsandmakeanychanges
tothegasfittings.• Deviceswithdifferentconnectingscrewsmaynotbeope-
rated.
Storing objects• Gasbottlesmustalwaysstandupright.• Cupboardsforgasbottlesmustbesealedupfromtheliving
quarters.• Cupboards for gas bottlesmust have a vent of at least
100cm2inordirectlyabovethefloor.
Gas 09-2
Regulators and valves• Pressuregovernorsmusthaveafixedpressureof30mbar.
TheregulationsinEN12864,AppendixD,applyaccordingly.Thepressuregovernorsmusthaveaminimumflowrateof1.2hx/h.
• Carefullyattachthehigh-pressurehoseonthebottlebyhand(note: left-handed thread).Donotusespanners,pincersorsimilartools.
• Ifthetemperatureisbelow5ºC,usethede-frostingfacility(ice-ex)forregulators.
Theoperatingpressureforgasis30mbar.
Operating the cooker• Whenoperatingthecooker,theskylightorthewindow mustbeopen.• Theoperatingleversofgasdevicesthatmustbepressed
toignitewhenturnedon,mustspringbackbythemselvesafterbeingpressed.
Cookers or other devices that use air from indoors for
combustionmayneverbeusedtoheatthevehicle.Ifthis
isignoreditcouldcausemortaldanger,duetothelackof
oxygenandthepossibledevelopmentofodorlesscarbon
monoxide.
Waste gas• Thewastegaspipemustbeattachedfirmlyandimpenetrably
totheheatingandthechimney.Itmaynotbedamagedinanyway.
• Waste gasmust bepassedoutwithout obstruction andfreshairmustbepassed inwithoutobstruction.For thisreason,theremaybenosnowwallsorskirtsdirectlynexttothevehicle.Theintakeopeningsontheunderbodyofthevehiclemustbekeptclearandclean.
Before initial operation• Keepallventsclear.• Removeanysnowfromchimney.• Clear aspirating holes for combustion air underneath the
vehicleofdirtand/orsnow.Otherwise,thewasteairmighthaveaCOcontentthatishigherthanallowed.
• Thesafetyventsmustnotbeclosed.• Never use portable cookers or heating devices, except
electricheatingdevices,butnotradiantheaters,becausetheycancauseafireorsuffocation.
Read themanufacturers‘ operatingmanuals thoroughly
andcarefully!
Gas09-3
orseparatelyinthesidewall,dependingonthemodel.
Gas bottle containerThegasbottlecontainerholds2x11kgpropanecylinders.Theseareconnectedtothegaspressuregovernormountedonthewallbymeansofhigh-pressurehoseswithintegratedsecurityagainstbreaking.Itisfittedoutwithagasflowmoni-torandanintegratedtestconnection.Therefore,heatingmayexplicitlybeoperatedwhiledriving.Thecyclindersaresecuredusingtwoindependentlashes.
Yourmobilehomehasbeenequippedwithapropanesystem(gasbottle not included in scopeof delivery). The followingequipmentrunsonthissystem:- cooker,- refrigerator,- waterheater,- oven
- andpossibly,specialequipment.
Gas containerislocatedintherearstoragecompartment
9.2 Gas supply
Gas 09-4
Stop valves and valves in the kitchen drawerThesevalvesareusetointerrupttheflowofgastothecorre-spondingdevice.Eachofthevalvesisidentifiedbyasticker.
The following applies for the gas bottle box:• Alwayscontrolthefasteningsbeforedriving.• Securelylashanyloosestraps.• Themaximumpressureinthehoseofthesafetyregulatormay
notbemorethan30mbar.
Thegasbottleroommaynotbeusedasadditionalstorage
room.Danger!Fire!
The following applies for stop valves and valves:• Allofthetapsongasdevicesmustbeshutwhiledriving.
Theonlyexceptionisforthetapsforheatingdevicesthataretobeusedwhiledriving.
Over the years, vibrations can cause slight leakages to
appear.Ifyoususpectthatthereareleakages,haveyour
dealeroranauthorisedworkshopforgasfacilitiescheck
yoursystem.
Leaktestsmayneverbecarriedoutnearanopenflame.
Gas
31
7
8
2
6
4
5
09-5
TheLPGheatingsysteminyourmobilehomehasbeen
designedtopermitoperationwhiledriving.Therequire-
mentsoftheEUGuideline2001/56/EGforheatingde-
viceshavebeenfulfilledsothat,incaseofanaccident,
LPGcannotescapeinvoluntarily.
9.3 Heating
Location of the operating device- Inthekitchenorbythemiddleseatingarrangement,depen-
dingonthemodel.
To operate• Removethechimneycap(notinscopeofdelivery).• Openthebottlevalveandthequick-actionstopvalveinthe
gaspipe.• Usetherotaryswitchtoadjusttheroomtemperature.The
equipmentisnowoperating.Thegreencontrollight“Ope-ration“undertherotaryswitchisshining.
Thedevicewillautomaticallyselecttherequiredlevelofper-formancefortheburner,dependingonthedifferenceintem-peraturebetweenthesettemperatureandthetemperatureatpresentintheroom.
Gas
31
7
8
2
6
4
5
09-6
For further information,please refer to theTRUMAope-
ratingmanual.
Malfunction• Incaseofmalfunction,theredcontrollight(8)lightsup.• Forpossiblecauses,pleaserefertotheTRUMAOperating
Manualforinstructionsonfindingdefects.• Tounlock,turnoffandthenonagain.
Turning off “Gas operation“• Usetherotaryswitch(6)toturnofftheheating.
Thewatermustbedrainedoffifthereisdangeroffrost!
Ifyoudonotplanonusingtheequipmentforalongerperiodoftime,closethequick-actionstopvalveinthegaspipeandthegasbottle.
Gas09-7
9.4 Refrigerator
Modes of operationThreemodesofoperationarepossiblefortherefrigerator.- 12Voperation:electricityissuppliedbythemobilehome‘s
battery.- 230V operation: electricity is supplied froman external
source.- LPG:suppliedbythegasbottlesinthemobilehome.
RefrigeratorsmanufacturedbyDometic or Thetford canbeused.
12 V operation12Voperationshouldonlybeusedwhiledriving,whenthemotor is running.When restingor ifyouhavestopped foralongerperiodoftime,turnoffthe12Voperation;otherwise,themobilehome‘sbatterywillquicklydischarge.
Donot run the refrigeratorongaswhiledriving.Danger
ofexplosion!
Beforeinitialoperation,pleaserefertothemanufacturer‘s
operatinginstructions.
9.5 Gas cooker
Thekitcheninthemobilehomehasbeenequippedwithagascookerwith3burners.
Before initial operation• Openthebottlevalveandthequick-actionstopvalveinthe
gaspipe.
Gas 09-8
2
1• Toturnoffthegasflame,turntherotaryswitchbacktothe
“0“setting.• Closethemaincockonthegascooker.
Usecookingglovesorpotholderswhenhandlinghotpots,
pansandsimilarobjects.Youmaybeburned!
After cooking, leave the glass covering open until the
burner no longer emits heat.Otherwise, theglassplate
couldburst.
Neverstoreeasilyinflammableobjectssuchasdishtowels,
serviettes,etc.,nearthecooker.Dangeroffire!
Operation• Openthetintedglasscovering(1).• Turntherotaryswitch(2)oftheburneryouwishtouseto
theignitionposition(largeflame)andpress.• Ignite theburnerwithagas lighterormatchorcigarette
lighter.• Continuetopresstherotaryswitchforafurther5-10seconds
toensurethattheautomaticflameguardtakeseffect.• Releaserotaryswitch(2)andturntothedesiredsetting(large
orsmallflame).• Ifignitionwasunsuccessful,repeattheprocedure.
Accessories
Accessories10-1
The following applies for the towbar coupling:• If a towbar coupling hasbeen subsequentlymounted, it
mustbeenteredinthevehicle'sdocumentsbytheTechnicalSurveyanceAssociation(TÜV).Thenecessarydocumentsareenclosedwiththetowbarcoupling.
•Notethepermittedloadfortherearaxle.•Notethepermittedbrakedtrailingload(seeTechnicalData).
(Noextraloadpossible.)•Permitteddrawbarload:75kg(formodelswithfront-wheel
drive)or80kg(formodelswithrear-wheeldrive).
Entry in the vehicle's documents• HaveyourHOBBYdealermountexternalconstructions.He
willalsohandlealltheformalitiesforyou.• Ifthisisnotthecase,driveyourmobilhometogetherwith
theregistrationdocumentsandthenecessaryexpertisefor
the external construction to theTÜV,where the externalconstructionwillbeinspectedandacorrespondingexpertiseissuedforregistrationinthevehicle'sdocuments.
• Present theexpertise to theDriverandVehicleLicensingAgency,wheretheamendmentswillbeenteredinthevehicle
documents.
In addition, note themanufacturer‘s operating instruc-
tions.
Mounting or subsequentmounting of hitches are not
permittedformodelsT600GFLC,T600GRSandT600
AKGFLC.
Chapter 10: AccessoriesOnly themost important accessories are described in thischapter.Pleasenotethemanufacturers‘detailedoperatinginstructions,installationinstructionsandcircuitdiagramsfortheaccesso-ries.
10.1 Towbar coupling
Accessories
Maintenance and Care
Maintenance and Care11-1
Chapter 11: Maintenance and Care11.1 Maintenance
Maintenance intervals
There are stipulated maintenance intervals for the mobile home and its equipment.
Also note the maintenance intervals for the basic Ford
vehicle.
The following applies for maintenance intervals:• HavethefirstmaintenancecarriedoutbyaHOBBYdealer
12monthsafterthevehiclewasfirstregistered.• Allfurthermaintenanceshouldbecarriedoutonceayear
byaHOBBYdealer.• Themaintenanceofthebasicvehicleaswellasallbuilt-in
equipmentshouldbecarriedoutat the intervalsgiven ineachoperatingmanual.
Thegasfittingsmustbecheckedevery2yearsbyanexpert
forliquidgasandconfirmedonthecertificateinaccordance
with DGVW G 607.
11.2 Airing
For a comfortable climate inside the caravan, there must be sufficientventilation.Thisalsoavoidscorrosivedamagedueto condensation.
Condensation is caused by- insufficientvolumeinsidethecaravan- breathingandperspirationofthepassengers- bringingindampclothing- operatingagascooker
Ensurethatthere isasufficientexchangeofairtoavoid
damagesduetothebuild-upofcondensation!
Theoperatorofthevehicleisresponsibleforhavingmain-
tenance carried out on schedule.
Replace the safety regulator for gas at least every 6
years!
Forsafetyreasons,sparepartsforequipmentmustconform
with the manufacturer‘s instructions and must be installed
byhimoradulyauthorisedrepresentative.
Maintenance and Care 11-2
11.3 Care
Cleaning the exteriorThe vehicle should not be washed more often than necessa-ry.
Washthevehicleonly inplacesprovidedforthispurpo-
se.
Usingcleaningmaterialssparingly.Aggressivecleansers,
suchaswheelrimcleaners,damagetheenvironment.
The following applies when cleaning the exterior:• Rinsethevehiclewithaweakjetofwater.• Wash the vehiclewith a soft sponge and a commercial
shampoosolution.Rinsethespongeoften.• Thenrinsewithagenerousamountofwater.• Drythevehiclewithasuedecloth.• Afterwashingthevehicle,leaveitstandingoutsidetodry
offcompletely.
Drytheheadlightsandsocketsthoroughly,aswatercollects
thereeasily.
The following applies when waxing the surfaces:• Thevarnishedsurfacesshouldbetreatedoccasionallywith
wax.Note the application instructions givenby thewaxmanufacturers.WerecommendproductsmadebyVALMA,turtle,FlashorSystem.
The following applies when polishing the surfaces:• In exceptional cases, use polish to refinishweathered
varnishedsurfaces.Werecommendsolvent-freepolishingpaste.
Usepolishonlyinspecialcasesandasseldomaspossible,
becausepolishremovesthetoplayerofvarnish.Frequent
polishingcausesextremewear.
The following applies for tar and resin stains:• Tarandresinstainsaswellasotherorganicstainscanbe
removed with petroleum ether or spirits.
Donotuseaggressivesolutionssuchasproductscontai-
ningesterorketone.
Maintenance and Care11-3
The following applies for damages:• Repairdamagesimmediatelytoavoidfurtherdamagesdue
tocorrosion.AskyourHOBBYdealerforassistance.
Windows and doors
The following applies for their care:• Rubtherubberjointsarounddoorsandwindowslightlywith
talcum powder.• Clean acrylic glasspanesonlywith a clean,wet sponge
andasoftcloth.Cleaningwithadryclothmayscratchthepanes.
Donotusestrongandaggressivesolutionsthatcontain
softenersorsolvents!
Youwillfindtalcumpowderinautoaccessoryshops.
Cleaning the interior
The following applies for cushions, upholstery and curta-ins:• Cleancushionswithasoftbrushorhoover.• Haveverydirtyupholsteryandcurtainsdry-cleaned.Donot
washthemyourself!
• Ifnecessary,washthemcarefullyusingthefoamfrommild-actiondetergent.
The following applies for carpeted floors:• Cleanwithahooverorbrush.• Ifnecessary,treatwithcarpetshampooorashampooing
machine.
The following applies for furniture surfaces:• Cleanthesurfaceofwoodenfurniturewithadampclothor
sponge.• Rubdrywithadust-freecloth.• Usemildfurniturepolish.
Never use strong-action cleansers or intenvise furniture
polish,becausethiscouldscratchthesurface!
The following applies for the toilet:• Cleanwithaneutral liquidcleanserandacloththatdoes
not scratch.
Neverusestrong-actioncleansersinthetoilet!
Maintenance and Care 11-4
Accessories
The following applies for their care:• Cleanplasticparts(e.g.fenders,skirts)withwaterofupto
60°Candmildhouseholdcleansers.• Cleangreasyoroilysurfaceswithspirits.• Ifnecessary,lubricatedoorhingesandlevelingsupports.• Cleanfreshwaterpipes,thefreshwaterandsewagetanks
onceayear.
Donotusestrong-actioncleansers,becausethesecould
scratchthesurface!
Removeallspraycanscontainingcleansingandcareso-
lutionsfromthevehicleafteryouhavefinished!Otherwise
theymayexplodeifthetemperatureexceeds50°C!
11.4 Operating in winter
Preparations
The following applies for preparations:• Checkvehiclefordamagetovarnishorrust.Ifnecessary,
repairdamage.• Ensurethatwatercannotgetintothecompulsoryventilation
inthefloorortheheating.• Protectthemetalpartsoftheunderbodyagainstrustwith
awaxpreservative.• Useasuitablematerialtopreservetheexteriorvarnished
surfaces.
Operating in winterDuringoperationinwinter,condensationiscausedwhenusingthevehicleinlowtemperatures.Sufficientventilationisextre-melyimportanttoensurethatthequalityoftheairinsidethevehicleisgoodandtoavoiddamagestothevehiclecausedbycondensation.
Maintenance and Care11-5
The following applies for ventilation:• Whenheatingthevehicle,turnuptheheatingtothehighest
positionandopenthecupboardsintheceiling,curtainsaswell as blinds. This ensures optimal ventilation.
• Onlyturnontheheatingwhenthecirculationfanison.• Airallcushionsinthemorning;airthestoragecompartments
anddrydampspots.
If,despitethis,condensationshouldbuildupsomewhere,
simplywipeitaway.
Frost protection
Iftheinteriorissufficientlyheated,thefreshwatertank,waterpipes and water heater should not freeze.
The following applies for the sewage tank:• Inverylowtemperatures,addantifreezerorcommonsaltto
thesewage.• Storesewageoutsidethevehicle.• Leavethedraincockofthesewagetankopen.
At the end of the winter season
The following applies for the care of the vehicle:• Thoroughlywashtheunderbodyandthemotor.Thisremoves
corrosivethawingagents(salts,alkali).
Washthevehicleonlyinplacesprovidedforthis
purpose.
Usingcleaningmaterialssparingly.Aggressivecleansers,
suchaswheelrimcleaners,damagetheenvironment.
Winterizing your vehicleIn general:• Onlyleaveyourmobilehomeinaclosedspaceifitisdry
andeasytoair.Otherwise,itisbettertoleaveyourmobilehome in the open.
The following applies for the interior fittings:• Empty therefrigeratorandclean it.Leavetherefrigerator
door open.
Maintenance and Care 11-6
• Leavestoragecompartmentsandcupboardsopentoair.• Placecushionsandmattressesinsuchawaythattheywill
not come into contact with condensation.• Ifnecessary,heatthemobilehometoavoidmildewdueto
condensation.• Place3kgofcommonsaltinabowltokeeptheinteriorof
thevehicledry.Thesaltwillsoakupanymoisture.Changeitregularly.
• Disconnectbatteries;ideally,removethemandcheckonceamonthiftheyarestillcharged,otherwisechargethem.
• Turnoffthe12Vmasterswitch.
The following applies for the exterior of the caravan and the basic vehicle:• Useasuitablematerialtopreserveexteriorvarnishedsur-
faces.• Protectthemetalpartsoftheunderbodyagainstrustwith
awaxpreservative.• Tocareforthewheels,jackupthevehicleormoveitfrom
onespottoanothereverytwomonths.• Useatarpaulin,leavingspacebetweenitandthevehicleto
ensuresufficientairing.• Leavethecompulsoryventilationopen.• Air yourmobile home thoroughly every three to four
weeks.
• Checktheantifreezerinthecoolingcircuit,refillingifneces-sary.
The following applies for containers:• Emptythefreshwatertankwithapumporwastevalveand
clean it.• Emptyandcleanthesewagetank.• EmptyandcleantheWCtank.• Completelyemptythewaterheaterbyswitchingthefresh
water pumpon theon-board control centre to “off“ andopeningallfaucets.
• Ensurethatwatercannotgetintothecompulsoryventilationinthefloorortheheating.
Alsonotetheinformationandoperatinginstructionsgiven
bythemanufacturersofthebuilt-inequipment.
Sanitation and Environmental Protection
Sanitation and Environmental Protection 12-1
Chapter 12: Sanitation and Environmental Protection
12.1 The environment and traveling
Environmentally fair useIt is only natural that owners of mobile homes and caravans have a special responsibility for the environment. Always use your vehicle in an environmentally friendly way.
The following applies for environmentally fair use:• Donotspoilthepeaceandcleanlinessofnature.• Dispose of sewage, excrements andwast in the proper
way.• Setanexamplesothatmobilehomeandcaravandrivers
arenotgenerallyheldtobepollutionists.
The following applies for sewage:• Collectsewageonboardonlyinbuilt-insewagetanksor,if
necessary,insuitablecontainers!• Never empty sewage inopen spacesordownmanholes!
Generally,thepublicsewagesystemdoesnotrunthrough
clarificationplants.
• Emptyyoursewagetankasoftenaspossible,evenifitisnot
completelyfull (hygiene). Ifpossible,rinseoutthesewage
tankwithfreshwaterafteremptying.
Onlyemptyyoursewagetankinspecialplacesforsewage
disposal, but never in open spaces!Generally, sewage
stationsarefoundinmotorwayserviceareas,campsites
or petrol stations.
Sanitation and Environmental Protection 12-2
Sanitation• Neverallowtheexcrementtanktobecometoofull.Empty
thetank immediatelyassoonasthe level indicator lightsup.
• Never empty excrements downmanholes!Generally, the
public sewage systemdoes not run through clarification
plants.
Empty theexcrement tank inspecialplaces forsanitary
disposal,butneverinopenspaces!
The following applies for excrements:• Onlyuseapprovedsanitarycleansingproductsintheex-
crementtank.
You may be able to avoid the use of sanitary liquids by
installing an activated carbon filter system (sold as an
accessory)!
Usesanitaryliquidsverysparingly.Anoverdoseisnogu-
aranteeofpreventingodours!
Sanitation and Environmental Protection 12-3
12.2 Returning the vehicle
Ifyoushouldeverhavetogiveupyourmobilehomeandhaveitrecycled,themanufacturerofthebasicvehicleisresponsiblefortakingitback(statusatthetimeofprinting).
ThismeansthatyourHOBBYmobilehomewillbetakenbackfreeofchargebyanyForddealerandexpertlyrecycled.
The following applies for waste:• Separateyourwasteandputappropriatematerials inthe
recyclingbins.• Emptywastebinsasoftenaspossible intheappropriate
bins or containers. This avoids unpleasant and problematic wastefrombuildinguponboard.
The following applies for picnic spots:• Alwaysleavepicnicspotscleanandtidy,evenifyoudispose
of someone else‘s waste.
Carefuluseoftheenvironmentisnotonlyintheinterest
of nature, but alsoofmobile homeandcaravandrivers
everywhere!
Sanitation and Environmental Protection
Technical Data
Technical Data13-1
Chapter 13: Technical Data
13.1 Weights according to 92/21/EWG, 2007 season
Model SeriesWeight of basic
vehicleDriver Diesel (kg)
Basic equip-ment
Mass when vehicle is ready
to start
Techn. perm. ove-rall weight
T 555 FS Siesta (C) 2560 75 68 116 2819 3500
T 600 FC Siesta (C) 2625 75 68 121 2889 3500
T 600 GFLC Siesta (C) 2720 75 68 121 2984 3500
T 600 GFS Siesta (C) 2710 75 68 121 2974 3500
T 650 FLC Siesta (D) 2835 75 68 121 3099 3500
T 650 FLC Siesta (D) 2835 75 68 40 3018 3500
T 650 GFLC Siesta (D) 2870 75 68 121 3134 3500
T 650 GFLC Siesta (D) 2870 75 68 40 3053 3500
T 555 AK LC Siesta (C) 2687 75 68 121 2951 3500
T 555 AK FS Siesta (C) 2645 75 68 116 2904 3500
T 600 AK GFLC Siesta (C) 2790 75 68 121 3054 3500
T 650 AK FLC Siesta (D) 2885 75 68 121 3149 3500
T 650 AK FLC Siesta (D) 2885 75 68 40 3068 3500
T 650 AK GFLC Siesta (D) 2899 75 68 121 3163 3500
T 650 AK GFLC Siesta (D) 2899 75 68 40 3082 3500
T 650 AK KLC Siesta (D) 2872 75 68 121 3136 3500
T 650 AK KLC Siesta (D) 2872 75 68 40 3055 3500
These figures refer to the standard vehicle without extra equipment. Deviations of up to 5 % are possible.
Over-load
weight
No. of seats
681 4
611 4
516 4
526 4
751 4
482 4
716 4
447 4
549 4
596 4
446 4
701 4
432 4
687 4
418 4
714 4
445 4
Technical Data 13-2
13.2 Inflation pressures
* These inflation pressures are only valid for standard tires by alternative manufacturers. In principle, we try to equip all ve-hicles with “Michelin Camping“ tires. In times of high demand, however, Michelin is unable to fulfil all demands. In this case, alternative brands are mounted, e.g. Pirelli.
Tires tire pressure (bar) Basis
Michelin XC Camping
215/75 R 16 C front: 3.5 rear: 5.5 FORD
other tire manufacturers*
185/75 R 16 C front: 4.7 rear: 3.5 FORD
215/75 R 16 C front: 3.5 rear: 4.75 FORD
Conventio-nal loading
Overload weight
Length of vehi-
cle
Personal equipment
Remaining overload weight
225 456 5,8 98 358
150 461 6,4 94 367
225 291 6,4 104 187
225 301 6,4 104 197
225 526 7,1 111 415
225 257 7,1 111 146
225 491 7,1 111 380
225 222 7,1 111 111
225 324 5,8 98 226
225 371 5,8 98 273
225 221 6,4 104 117
225 476 7,1 111 365
225 207 7,1 111 96
225 462 7,1 111 351
225 193 7,1 111 82
225 489 7,1 111 378
225 220 7,1 111 109
Model
T 555 FS
T 600 FC
T 600 GFLC
T 600 GFS
T 650 FLC
T 650 FLC
T 650 GFLC
T 650 GFLC
T 555 AK LC
T 555 AK FS
T 600 AK GFLC
T 650 AK FLC
T 650 AK FLC
T 650 AK GFLC
T 650 AK GFLC
T 650 AK KLC
T 650 AK KLC
Index
IndexI-1
Index
AAccessories care of 11-4Airing 11-1
BBattery charger location 06-5 Beds, rearranging lift-off table construction 07-12Brakes 02-5, 04-5Breakdown of devices 06-8
CCaravan battery 06-6 changing the battery 06-7 features 06-6 location 06-6Care 11-2 of windows and doors 11-3 of furniture surfaces 11-3 of cushions and upholstery,curtains 11-3 ofcarpetedfloor11-3 of toilet 11-3 of accessories 11-4Changing a tire 04-5Charging procedure 06-5 with running motor 06-5 protecting the device 06-5 protection against total
discharge 06-4Chassis 03-1Checking the gas supply 9-1Circuit diagram interior 06-11Compulsory ventilation 05-3Condensation 11-1Cupboard doors with push-button knob 07-1
DDay and night position overview 07-15Display elements 06-2Doorsandflaps interior 07-1Doors opening and closing 05-5Driving 02-5 curves 02-6 protecting your tires 04-1 in reverse 02-6Driving in reverse 02-6Driving through curves 02-6
EEconomic driving 02-6Electric power supply 06-3Electric power supply unit 06-4Electric system fuses 06-7Electrical installations safety instructions 06-1
Emergency equipment 02-7 fireextinguisher02-8 first-aidkit02-7 warning triangle 02-8Entrance door 05-5Entrance step 03-8Environment 12-1 waste 12-3 sewage 12-1 sanitation 12-2 excrements12-2 picnic spots 12-3Environmental protection 12-1Exteriorgassupply05-7Exteriormirror05-9Exteriorshower water supply 05-8 cleaningtheexterior11-2 polishing 11-3 waxing11-2Exteriorsocket05-9Externallymountedconstruc-tions 03-9
FFireextinguisher02-8First-aid kit 02-7Flaps opening and closing 05-5Flushing toilet 08-4Freshwaterfillerneck05-8Fresh water tank 08-1 to empty 08-2
to get water 08-1 tofillwithwater08-1Furniture surfaces care of 11-2Fuse protection of elec. system12 V circuits 06-7 information on fuses 06-8 starter battery 06-9
GGas 09-1Gas bottle container 09-3Gasbottleflap05-7Gas cooker 09-7 to operate 09-8 putting into operation 09-8Gas supply 09-3General inspection 02-1
HHalogen lights to change 06-9Headrests adjusting the height 07-19Heating to turn off 09-6 to operate 09-5 location of operating device 09-5 malfunction 09-6Hot water supply function 08-4
Index I-2
IInflationpressure04-2Inflationpressurevalues13-2
KKeys to the vehicle 05-5Knockout windows 07-4
LLevelling supports 03-10Light switches 07-2Lights changing halogen lights 06-9Loading 03-1Loads formaxichassis03-3 for special releases 03-4LPGfittings waste gas 09-2 quick-action stop valves and valves 09-4 location 09-4 built-in objects and changes 09-1 checking 09-1 regulators and valves 09-2Luggagetrunkflap05-6
MMains supply 06-3Maintenance intervals 11-1Maintenance brake system 04-5
Maximumspeed02-9Maximumspeeds02-9Media unit 07-22
OOn-board control panel 06-1Operating in winter 11-4 sewage tank 11-5 ventilation 11-5 frost protection 11-5 preparations 11-4Operating the cooker 09-2
PPetrol 02-6Preparing the vehicle 02-2Protection against total dis-charge 06-5
RRefrigerator 09-7 230 V operation 09-7 to operate 09-7 modes of operation 09-7 gas operation 09-7 ventilation 05-3 locking the door 09-7 operating in winter 05-3Registration 02-1Regulator 09-2Residual current operating device 06-5Resin stains 11-2
Roof load 02-4
SSaving energy 02-6Seatbelts in caravan 07-10Seating arrangements overview 07-14Seats in caravan 07-10Securing the vehicle 02-12Selecting a parking space 02-12Serviceflaps05-1Sewage tank 08-6 to empty 08-6Shunting 02-5Skylights 07-5 with combined blind 07-5 combining blinds 07-5Sunroof with combined blind 07-7Sunshade 07-5 combined with blinds 07-5 to adjust 07-6Switching electric consumption 02-12
TTankflaps05-1Tar stains 11-3Technical data sheet 13-1Toiletflap05-7
Toiletcare of 11-3Toiletuse of 08-5 C 200 E cassette 08-6 C 200 S cassette 08-6 emptying cassette 08-7Towbar coupling 10-1Tread depth 04-2Tires 04-1
VValves 09-2
WWarning triangle 02-8Waste gas 09-2Water boiler 08-9 to empty 08-9 tofill08-9 operating in summer 08-10 malfunction 08-12Watersupplyforexteriorshower05-8Weight of accessories 03-1Wheel rims 04-3Winterizing your vehicle 11-5 exteriorofcaravanandbasic vehicle 11-6 containers 11-6 interiorfittings11-5
Appendix
AppendixA-1
Calculating masses for HOBBY mobile homes
The following table enables you to calculate the mass of your own mobile home on the basis of the mass data given in this manual.
This calculation must always result in a positive remaining load in order to fulfil current legal requirements.
To determine your remaining load, simply subtract the "mass when the vehicle is ready to start", the "conventional load", all "additional
equipment" as well as your "personal luggage" from the "technically permissible overall mass". Simply enter the date for your personal
mobile home in the table on the next page. If you have any questions or if anything is unclear, your HOBBY dealer will be pleased
to assist you.
Your
HOBBY Motor Home Plant
Ing. Harald Striewski GmbH
Appendix A-2
Technically permissible overall mass:
Mass when the vehicle is ready to start (incl. gas, water, electricity, driver and fuel): -
Conventional load (no. of seats [excl. driver] x 75 kg: -
Additional equipment:
1.) -
2.) -
3.) -
4.) -
5.) -
6.) -
7.) -
8.) -
9.) -
10.) -
11.) -
12.) -
13.) -
14.) -
15.) -
Personal luggage = (10 x N) + (10 x L): -
N - Total number of seats (incl. driver)
L - Length of vehicle in meters
Remaining load:
Model:
Under no circumstances may the technically permissible overall mass of
the mobile home be exceeded!