Research ArticleDesign and Analysis of an Optical Coupler for ConcentratedSolar Light Using Optical Fibers in Residential Buildings
Afshin Aslian,1 Barmak Honarvar Shakibaei Asli,2,3 Chin Joo Tan,1
Faisal Rafiq Mahamd Adikan,2 and Alireza Toloei4
1Department of Mechanical Engineering, Faculty of Engineering, University of Malaya, Lembah Pantai,50603 Kuala Lumpur, Malaysia2Integrated Lightwave Research Group, Department of Electrical Engineering, Faculty of Engineering, University of Malaya,Lembah Pantai, 50603 Kuala Lumpur, Malaysia3Institute of Information Theory and Automation, Academy of Sciences of the Czech Republic, Pod Vodarenskou vezฤฑ 4,182 08 Praha, Czech Republic4Faculty of New Technologies Engineering, Shahid Beheshti University, District 1, Daneshjou Boulevard, Tehran 1983963113, Iran
Correspondence should be addressed to Chin Joo Tan; [email protected]
Received 7 December 2015; Revised 7 April 2016; Accepted 21 April 2016
Academic Editor: Manuel Fuentes Conde
Copyright ยฉ 2016 Afshin Aslian et al. This is an open access article distributed under the Creative Commons Attribution License,which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.
Concentrated sunlight that is transmitted by fiber optics has been used for generating electricity, heat, and daylight. On the otherhand, multijunction photovoltaic cells provide high efficiency for generating electricity from highly concentrated sunlight. Thisstudy deals with designing and simulating a high-efficiency coupler, employing a mathematical model to connect sunlight withfiber optics for multiple applications. The coupler concentrates and distributes irradiated light from a primary concentrator. Inthis study, a parabolic dish was used as the primary concentrator, a coupler that contains nine components called a compoundtruncated pyramid and a cone (CTPC), all of which were mounted on a plate.Thematerial of both the CTPC and the plate was BK7optical glass. Fiber optics cables andmultijunction photovoltaic cells were connected to the cylindrical part of the CTPC.The fiberswould transmit the light to the building to provide heat and daylight, whereas multijunction photovoltaic cells generate electricity.Theoretical and simulation results showed high performance of the designed coupler. The efficiency of the coupler was as high as92%, whereas the rim angle of the dish increased to an optimum angle. Distributed sunlight in the coupler increased the flexibilityand simplicity of the design, resulting in a system that provided concentrated electricity, heat, and lighting for residential buildings.
1. Introduction
Stand-alone or net-zero energy buildings are residential orcommercial buildings with greatly reduced energy needs [1].The consumed energy in a residential building can be invarious forms, including light, heat, and electricity. Electricpower generation from sunlight and its conversion to heator light has a low efficiency. In concentrated photovoltaicsystems, the temperature of the photovoltaic module andcoupler increases; therefore, a cooling system is required.Moreover, concentrated photovoltaic and thermal (CPVT)systems demonstrate higher efficiency versus conventionalthermal solar systems [2].
More than 30 years ago, a group of researchers studied thetransport of solar energy via fiber optics [3].This idea inspiredother researchers because of many potential applications ofthis kind of solar system, including the production of passivedaylight [4] and solar surgery [5] and using solar energy forheating or cooling [6, 7]. However, some disadvantages suchas the cost of fiber optics cables [8], the effect of dust [9], andthe high temperature of concentrated light on the tip of fibers[10โ12] have prevented commercial use of the system. Such asystem compromises a concentrator, a tracker for high con-centration, a sunlight coupler, and fiber optics. Other devicessimilar to photovoltaic (PV) cells and heat exchangers maybe added for use with different applications. Improvements
Hindawi Publishing CorporationInternational Journal of PhotoenergyVolume 2016, Article ID 3176052, 11 pageshttp://dx.doi.org/10.1155/2016/3176052
2 International Journal of Photoenergy
in the components have encouraged researchers to attemptovercoming previous obstacles. Concentrators are generallygrouped by optical characteristics, including low (less than100x), medium (100xโ300x), and high (more than 300x)concentrations. However, all proposed systems increase theintensity of light, and hence fewer PV cells or heating surfacesare required for generating electrical power or heat. Thisstrategy will reduce the cost of the total system and landutilization [13]. High concentration is required for focusingsunlight into fiber optics. Parabolic mirror dishes are widelyused in solar energy applications for highly concentrating thesunlight. The parabolic dish is an important subsystem thatoffers the highest thermal and optical efficiency among otheroptions [14]. The cost of this component has a noticeableeffect on the total cost of the system. In terms of scale, twoapproaches are proposed to gain the maximum efficiency ofsunlight. Each approach alters the design of the coupler andother components differently. The first approach considersa solar dish with a diameter either equal to or larger than1m as a large dish, and it is far more expensive than aminidish (diameter less than 1m). In this case, the windforce significantly affects the design of the tracker and thestructure of the system. Nevertheless, because it requiresfewer components, the overall cost decreases in large-scalepower plants using large dishes. Thus, novel designs havebeen introduced to reduce the cost of large-scale solar dishesin the last decade [15, 16].
Small dishes are proposed for high concentration and thegeneration of daylight as the second approach [17].The spatialrestrictions for installing large dishes on rooftops prompteddesigners to use minidishes or an array of minidishes forresidential applications [18]. Coupling a premier concentratorwith fiber optics and, simultaneously, increasing the concen-tricity of light with high efficiency have been a significantchallenge. When a bundle of fiber optics is placed at the focalpoint of the dish, the tip of the fiber is exposed to intenseheat. This is because the bundle has a total core area that isless than 50% of the cross-sectional area of the bundle. Theconcentrated sunlight, which propagates on the clad or gap ofthe bundle, will be converted to heat [10]. On the other hand,the acceptance angle of fibers is limited, and the concentratedsunlight has to be transmitted inside a small cone angle.Because of that, the portion of sunlight with an angle morethan the critical angle is not transmitted by the fiber optic.Furthermore, concentrating high-intensity sunlight into aspot with tiny-diameter fiber optics is not practical; therefore,bundles of fibers have been used for transmitting sunlight[19]. However, using more fibers increased the cost. To tacklethese problems, various systems andmethods have been usedto maximize the concentration and homogenization of thelight. In 1996, Winston and Ning introduced a coupler, calleda nonimaging radiant energy device, that included a convexlens at the inlet, a nonimaging hyperbolically shaped device,and a concave lens at the outlet [20].
In another study, a bundle of fibers transmitted sunlightwhile a parabolic dish was applied as the main concentrator.The coupler consisted of a secondary mirror and an asphericlens [19]. Feuermann and Gordon worked on the usage ofsolar fiber optics inminidishes, and they presented a coupling
with a single compound parabolic concentrator (CPC) thatwas placed in the dish and received the light reflected froma small flat mirror. The CPC collected sunlight and wascoupled with the fiber optic cable [12]. They also used fiberas a direct receiver of light and compared it with the CPCcoupler [21]. He et al. [22] designed and implemented a novelconcentrator and coupler based on a solar fiber lamp. Theirproposed design was composed of a concentrator with acompound curved surface and a coupler. The coupler wasmade of a cylindrical mirror surface, a deflector, a CPC, andfiber connected to the endpoint of the CPC.
Ullah and Shin studied highly concentrated optical fiber-based daylighting systems that used CPCs for coupling fiberswith the generation of concentrated light by a primaryconcentrator [23]. Yu et al. [24] investigated the usageof miniature dielectric compound parabolic concentrators(DCPCs) for day lighting. Arnaoutakis et al. showed ray-tracing simulations of a novel two-stage coupler that had alens and a dielectric taper of the circular cross section thatwas directly attached to the optical fiber [25].
This paper introduces a new coupler based on dividingsunlight using the proposed compound pyramid and coneshape implemented in a concentrated photovoltaic, thermal,and lighting system. Each CTPC can be connected to thecore of one fiber.Therefore, the loss would be reduced, whichleads to the reduction of temperature on the tips of thefiber optics. An analytical model was developed to designthe components of this structure. The new design is capableof transmitting sunlight into fiber optics and working as asecondary concentrator. It also reduces the angle of incidentlight before entering the fiber optics while simultaneouslyincreasing the coupling efficiency by reducing the number ofoptical components with different mediums. We divided thesunlight into nine beams, where each beam hits one CTPCwith small angle of incidence. The designed CTPC facilitatesthe assembly process of fiber optics and coupler. The designof the coupler is simulated and the results are presented.
2. Coupling Design, Theory, and Methodology
Figure 1 shows a schematic of the proposed coupler, dish,and fiber optics. The coupler is attached to the dish and fiberoptics. The dish is used as a primary concentrator, and thefiber optics transmit the sunlight.
The proposed coupler includes nine CTPCs mounted ona transparent plate. The coupler is placed a few millimetersfrom the focal point of the dish. Since the refractive indexof the plate is higher than that of air, it reduces the refractedangle of light. Considering prototype methodology, two dif-ferent concepts were developed. First, a prototyping processwith a flat plate as the base of the coupler was assumed. Inthis case, the bottom of each CTPCwas cut to a specific angle.In the second approach, one side of the plate was machinedso that it could contain nine square surfaces with differentangles. In this case, all the CTPCs were the same, whichrendered themmore suitable for mass production. As shownin Figure 2(a), according to the first concept, the surface ofthe bottom side of the CTPCs is rectangular in order toaccommodate them on the flat plate with no empty space (see
International Journal of Photoenergy 3
Detail A
A
Fiber optics
Coupler
Case of coupler
Stand of coupler
Cable of fibers
Figure 1: Schematic of a parabolic dish, coupler, and fiber optics.
(a) (b)
Figure 2: Assembly of coupler: (a) concept of flat plate and (b) concept of carved plate.
Figure 3(a)). The bottom side is also cut with an angle to thesymmetrical axis of the CTPCs. This angle tilts the CTPCsas they sit on the plane, which reduces the entrance angle oftransmitted light. The upper side of the CTPCs is carved intoa cone shape and extended to form a cylinder.The cylindricalpart of the CTPCs could be aligned easily with the fiber opticsand spliced to the core of the fiber. A customized adapterwith mating sleeve, ferrule, and epoxy is used for connectingCTPC to fiber optics. Using dense array of CTPCs instead ofone cone or CPC increases the rim angle whereas it reducesthe loss by connecting one fiber to one CTPC instead ofconnecting bundle of fibers to one cone or CPC. The verticalCTPC, shown in red, is located at the center of the plate. FourCTPCs, shown in yellow, are positioned at the side of plateat the same angle, and four more CTPCs, shown in green,are placed at the same angle at the four corners of the flatplate.
In the second concept, the plate is carved into squaresurfaces with different angles; therefore, the bottom sides
of the CTPCs are perpendicular to the symmetrical axis.This structure is shown in Figure 2(b). As can be seenin Figure 3(b), unlike the first approach, the plate is notflat and the CTPCs stand on the carved surface with noempty space. However, according to derived simulations,both concepts have the same results. The coupler could bemanufactured using grinding process and molding. CTPCsmay be produced and then assembled on the plate. Inthis case, proper glue is needed in assembly process. Byusing the extra numbers of CTPCs, the total surface areaof the cores connected to the coupler increases, and thusthe coupler could be used for larger primary concentrators.An investigation into the cost effectiveness of such a systemis needed in order to optimize the size of the primaryconcentrator for different applications. In experiment, perfectalignment of the fiber cores will reduce the loss. On theother hand, smoothness of the tip of CTPCs is crucial forreduction of loss. furthermore, the error in angle betweenCTPCs decrease the efficiency of the coupler.
4 International Journal of Photoenergy
(a) (b)
Figure 3: CTPCs cross section: (a) flat design and (b) carved design.
ฮ๐
ฮ๐
๐s
๐s
d
2
rD
2
๐
Figure 4: Concentrated sun flux by a parabolic dish mirror.
2.1. Plate Design. The inlet light of coupling comes from theprimary concentrator. Figure 4 shows the flux of sun that isilluminated on a dish with an aperture of๐ท. The rim angle is๐, the sunlight angle is ๐
๐ , and the diameter of concentrated
light is ๐. An acceptable precision for ๐๐ is 0.27โ, and the
occurrence of the probable cumulative errors in the systemis given by ฮ๐. The sources of error in the system are animperfect surface, the structure, movement, alignment, andthe sensors of the sun tracker, and so forth. The diameter ofconcentrated light is given by [26]
๐ =๐ท sin (๐
๐ + ฮ๐)
sin๐ cos (๐ + ๐๐ + ฮ๐)
. (1)
To minimize the diameter of concentrated light, the rimangle is considered to be 45โ. Therefore, we can rewrite (1) as
๐ =2๐ท sin (๐
๐ + ฮ๐)
cos (๐๐ + ฮ๐) โ sin (๐
๐ + ฮ๐)
. (2)
Tracking angle error (deg.)
Con
cent
ratio
n ra
tio
20003000400050006000700080009000
100001100012000
0 0.05 0.1 0.15 0.2 0.25 0.3
Figure 5: Variation of geometrical concentration of a parabolic dishwith respect to errors for 45โ rim angle.
Based on the derived diameter and the definition of thegeometrical concentration (๐ถ = (๐ท/๐)
2
), we have [27]
๐ถ =1 โ sin 2 (๐
๐ + ฮ๐)
4 sin2 (๐๐ + ฮ๐)
. (3)
Figure 5 shows a reduction of the geometrical concentra-tion of a parabolic dish as the systemerror increases fromzeroto 0.3โ. On the other hand, the diameter of the concentratedlight increases significantly with increasing errors, which isillustrated in the same figure. Calculation of the concentratedlight diameter leads to computation of the dimensions of theplate, with the assumption that the length of the square plateis equal to the focal point diameter.
2.2. CTPC Design. A truncated cone is a simple shapethat is widely used as a coupler located between the firstconcentrator and the fiber optics/photocells. In comparisonwith compound parabolic concentrators (CPCs), it showsbetter performance than cones; however, producing CPCs ismore difficult and expensive. Williamson [28] illustrated a
International Journal of Photoenergy 5
k shows the number of reflectionsk = 1
k = 2
k = 3
๐ผ
h
D3D2D1D0
๐in
๐1
๐2๐3
๐N
X1 X2 X3 XN
๐out
ยท ยท ยท
Figure 6: CTPC with total internal reflection and the dimensions of reflection points.
geometricalmethod of ray tracing in a simple cone, andWitte[29] demonstrated that the same procedure is applicable forskew rays. Myer [30] implemented the same method for theconcentration of collimated paraxial rays in a cone. Here, wedevelop a new approach for designing CTPCs for couplersconnected to fiber optics. The proposed CTPC design can bedivided into two parts. The first part involves the calculationof the maximum amount of total reflection based on thevariation of the inlet light and CTPC angles. The second partinvolves the calculation of CTPC dimensions with respect tothe amount of total reflection.
2.2.1. Calculation of CTPCAngle. Figure 6 shows aCTPC andmeridian ray with three total internal reflections. Based onSnells law,
๐1sin ๐in = ๐2 sin ๐1, (4)
where ๐1is the refraction index of the medium of the inlet
ray, ๐2is the refraction index of the CTPC, ๐in is the angle of
incident light to the forward surface, and ๐1is the refracted
angle. To satisfy the total internal reflection condition on thebody of CTPC,
๐2= ๐3;
sin ๐2>๐1
๐2
,
(5)
where the angle of the first incident light to the side wall is ๐2
and ๐3is the first total reflection on the side wall of the CTPC.
At the first incident light to the side wall of CTPC,
๐2=๐
2โ (๐1+๐ผ
2) , (6)
where ๐ผ is the CTPC angle equal to the angle of the pyramid.Substituting (6) into (5) yields
cos(๐1+๐ผ
2) >
๐1
๐2
. (7)
For the number of reflections on the sidewall, ๐, with totalinternal reflections, we have
๐1< cosโ1 (๐1
๐2
) โ ๐๐ผ
2. (8)
Since an optical fiber with a core and cladding is con-nected to CTPC, in order to prevent reflection on the end ofits surface, we use
sin ๐out โค โ๐2core โ ๐2clad, (9)
where ๐core and ๐clad are the refractive indexes of the coreand cladding, respectively. On the other hand, these two fiberparameters can be related to the numerical aperture (NA =
โ๐2core โ ๐2
clad). The output angle of transmitted light fromCTPC is indicated by ๐out. By using the relationship betweenthe internal angles of the designed CTPC in Figure 6, we canobtain
๐๐= ๐1+ ๐๐ผ, (10)
where ๐๐is the incident angle of light to the output surface
of CTPC. By applying Snells law for CTPC and optical fiber,we obtain
๐2sin ๐๐= ๐core sin ๐out. (11)
Substituting (11) for (10) and using (9), we find ๐1as
๐1โค sinโ1 (
๐core๐2
โ๐2core โ ๐2
clad) โ ๐๐ผ. (12)
Figure 7 compares the variations of ๐1in terms of the
number of total reflections based on two different relationsderived from (8) and (12).The assumed refractive indexes are๐1= 1, ๐
2= 1.517, ๐core = 1.459, and ๐clad = 1.378.
According to Figure 7, there are two different approachesto obtaining the maximum value of ๐
1with various angles
of CTPC. The upper lines show the mentioned value for the
6 International Journal of Photoenergy
0 1 2 3 4 50
10
20
30
40
50
Number of total reflections (k)
Max
imum
angl
e๐1
(deg
.)
๐ผ = 2โ
๐ผ = 2โ
๐ผ = 4โ
๐ผ = 4โ
๐ผ = 6โ
๐ผ = 6โ
๐ผ = 8โ
๐ผ = 8โ
๐ผ = 10โ
๐ผ = 10โ
Figure 7: Maximum angle of ๐1with respect to the number of total
reflections on the body and the end surface (to prevent reflection)for different CTPC angles.
total reflection insideCTPC,whereas the lower lines show themaximum value of ๐
1for preventing reflection at the end of
CTPC. Connecting the inlet light angle ๐in to ๐1 using (4) and(12) yields
๐in
โค sinโ1 [[
[
๐2sin (sinโ1 ((๐core/๐2)โ๐2core โ ๐2clad) โ ๐๐ผ)
๐1
]]
]
.
(13)
Figure 8 shows the inlet angle versus the maximumnumber of total reflections on the body of CTPC. For aspecific inlet angle (๐in), the number of total reflections (๐)decreases with increasing CTPC angle (๐ผ).
2.2.2. Calculation of CTPC Dimensions. Figure 9 illustratesa simple general model of CTPC that was indicated inFigure 6. This figure shows the reflected light at two points.The minimum length of CTPC for an optimized number ofreflections can be obtained from the summation of distances(๐๐) between the points of reflection (i.e., ๐ด and ๐ถ). The
first reflection may occur at any point on the inner surfaceof CTPC.
To find a relationship between the length of CTPC(๐ฟ) and the different parameters of the designed CTPC,such as the base lengths for various points of incidentlight (๐ท
0, ๐ท1, . . . , ๐ท
๐โ1, ๐ท๐) and angle (๐ผ), we define ๐
๐
in terms of the refracted angle (๐1) and the CTPC angle
as
๐๐= ๐1+ (๐ โ 1) ๐ผ, (14)
0 2 4 6 8 10 12 140
5
10
15
20
25
30
35
40
45
50
Number of total reflections (k)
Max
imum
angl
e๐in
(deg
.)
๐ผ = 2โ
๐ผ = 4โ
๐ผ = 6โ
๐ผ = 8โ
๐ผ = 10โ
Figure 8: Maximum angle of ๐in with respect to the number of totalreflections for different CTPC angles.
where ๐ is the number of reflections and ๐ โฅ 1. On the otherhand, using the tangent formula in the right triangle ABCyields
tan๐๐=๐ต๐ถ
๐ด๐ต=๐ท๐โ1
โ ๐ต๐ธ
๐ด๐ต. (15)
Since the angle ๐ต๐ด๐ธ is half of the CTPC angle, for the righttriangle ABE, we have
tan ๐ผ2=๐ต๐ธ
๐ด๐ต. (16)
By combining (14) and (15) using (16) and considering ๐ด๐ต =
๐๐,
tan [๐1+ (๐ โ 1) ๐ผ] =
๐ท๐โ1
๐ด๐ตโ tan ๐ผ
2. (17)
It is clear in Figure 9 for the right triangleMNP that
tan ๐1=๐ท0โ โ โ ๐ค
๐1
(18)
and that for triangle PMQ
tan ๐ผ2=
๐ค
๐1
. (19)
By eliminating ๐ค between (18) and (19), we get
๐1=
๐ท0โ โ
tan (๐ผ/2) + tan ๐1
. (20)
In the first reflection (see Figure 6), it is apparent that thefirst base length (๐ท
1) of CTPC is
๐ท1= ๐ท0โ 2๐1tan ๐ผ
2. (21)
International Journal of Photoenergy 7
๐ผ
h
wM
Q
PA
N
L
C
E
B
D0
๐1
X1 Xk
Dkโ1 Dk
๐k
๐ผ
2
๐ผ
2
Figure 9: Total internal reflection of incident light in a CTPC at ๐th reflection.
Using a mathematical induction of (20), the distancebetween reflection points can be derived as follows:
๐๐=
๐ท๐โ1
tan (๐ผ/2) + tan (๐1+ (๐ โ 1) ๐ผ)
; ๐ โฅ 2, (22)
where ๐ท๐โ1
can be obtained using the following recurrencerelation:
๐ท๐= ๐ท๐โ1
โ 2๐๐tan ๐ผ
2; ๐ โฅ 1. (23)
Finally, integrating the above calculated distances allows usto find the length of CTPC as
๐ฟ โค
๐
โ
๐=1
๐๐. (24)
The upper side of CTPC is shaped as a cone (see Figure 3).Therefore, the derived equations are applicable to the conepart as well. The thicker diameter of the cone is the chord ofthe square base of the pyramid, which reduces the maximumamount of incident light. The maximum concentration ofsunlight in the proposed design is limited by the refractiveindex (๐core) and sunlight angle (๐
๐ ) based on the following
equation [26]:
๐ถmax โค๐2
coresin2๐๐
. (25)
Therefore, in designing the coupler, the above limitation oftotal concentration must be considered.
3. Coupler Modeling
A coupler was designed based on the derived equationsof Section 2 to design a plate and CTPC. We assumed900W/m2 as the total integrated power intensity of the sunfor an ๐ด๐ 1.5 ๐ท reference spectrum (ASTMG 173) [31]. Thecalculated angle between CTPCs was 9.5โ. The geometricalconcentration of CTPC was 1.97 and the input power of
Figure 10: CAD prototype of coupler.
the coupler was assumed to be 300W for a dish with a650mm aperture diameter. Using CAD modeling software,a 3D model was created to be used in further studies of theexperimental model and the fabricating process. Figure 10shows a CAD prototype of the proposed coupler.
The 3D model was developed using a nonsequentialmodel for ray tracing in Zemax software. The rim angleof the dish was considered to be 45โ, which concentratedthe light directly onto the coupler. Hence, the multipointsources of light were assumed to propagate the light withfive wavelengths from 400 to 800 nm in our simulation. Theangle of propagation was 45โ, and a detector was locatedbehind the point source, whereas each CTPC had a smaller-diameter detector. The coupler was placed a few millimetersfrom the focal point, and therefore the rays were divergent.In the simulation, ๐ต๐พ7 was considered as a material for thecoupler. The wavelengths in the simulation were 400, 550,and 700 nm. Figure 11 shows a layout of the coupler with aray tracing format in shaded and 3D models. If the diameterof concentrated light and the occurrence of the probablecumulative errors in the system are to be determined, thediameter of the dish could be calculated using (2). As aninstance, the aperture of the dish for a couplerwith 26.01mm2entrance surface and nine fiber optics with 1mm diameterof core and total error of 0.1โ would be 392mm. On a clearday, 900 watts of solar energy per square meter is expectedof absorption area. A dish with 1160mm aperture is neededfor a coupler including 25 CTPCs. Considering the efficiencyof the entire system 30% so 280 watts of electrical output
8 International Journal of Photoenergy
(a) (b)
Figure 11: Layout of coupler for ray tracing: (a) shaded model and (b) 3D layout.
0
20
40
60
18.2
36.716.6
37.3
56.1 39.3
16.8
38.8 15.9 Wat
t
Figure 12: Distribution of power amplitudes (in watts) transmitted by CTPCs for a 300W input.
would be available from one dish. Take into account 1โ3 kw for a typical house, which would require 4โ12 dishes.Depending on the site, the array of dishes can be mountedon the rooftop or on the ground near the building. Totally,100โ300 fiber optics with one millimeter diameter of coreis required, respectively, for 1โ3 kw output, bearing in mindthat the length of fibers used for generating electricity isless than the fibers used for daylighting. The cost of fiberoptics is dominated by the production process, and only(around 10%) small fraction accounts for material. If weassume that the production cost is the same as commonmass-produced single mode silica fiber with outer diameterof 0.125mm ($0.1/m) and allocates the cost of the fused silica($250/kg), the cost would be ($0.53/m) for fiber optics with1mm diameter of core. So it is reasonable to assume that ifmassive demand arises, then the cost of fiber optics for 1โ3 kwwill be $590โ$1760 for the couplers with 25 CTPCs.
4. Simulation Results and Discussion
The efficiency of the designed coupler under noncollimateirradiation, the angle of inlet light into the fiber optics,
and the propagated light intensity via the components wereinvestigated by ray tracing. This efficiency was calculated bydividing the total occupied powers by CTPCs to the lightsource power through the following equation:
eff =โ๐
๐=1๐๐
๐
๐in, (26)
where ๐๐ is the power transmitted by each fiber optic, ๐inis the total inlet power of the coupler, and ๐ is the numberof CTPCs. Figure 12 shows the power transmitted by eachCTPCwhile 300Wpower was applied bymultipoint sources.Although there was significant variation between the powertransmitted by CTPCs on the corners, sides, and center,the amounts of power transmitted by the CTPCs that werepositioned on the sides or corners were close to each other.
The efficiency of the designed coupler was 92% in thesimulation. Fresnel reflection on the surfaces of the opticalcomponents caused a loss of power. In this coupler, Fresnelreflection only occurred on the flat plate surface. Incoherentirradiance of the transmitted light and the distribution ofradiant intensity by CTPCs are shown in Figure 13 for 10W
International Journal of Photoenergy 9
1711401128765453017820
3442822251741309260341640
1791461179167483118820
41033626820815510971351950
53543835027120214393542560
2802291831421067549281330
1651351088362442816720
3462832261751319260351640
1721411128765463017820
Figure 13: Distribution of radiant intensity for CTPCs according to their position.
source power. The maximum intensity of light was exhibitedby the centrally placed CTPC and the least intensity oftransmitted light was exhibited by CTPCs positioned on thecorners of the plate. The loss due to Fresnel reflection onthe tip of fiber optics and the loss of connector were nottaken into account in calculating the efficiency of coupler.Considering 4% loss as normal reflection on fiber tip and 11%(0.5 dB) in connecting multimode fiber to the coupler, theefficiency reduces to 77%. Refractive index of BK7 reducesfrom 1.5308 at 400 nm to 1.5108 at 800 nm [32].The efficiencyof the coupler reduced while the wavelength increased. Thereduction of efficiency was less than 1.5%.
The angle of inlet light into the fiber optics plays a key rolein reducing the light leakage of fiber optics in the transmis-sion of sunlight [33]. Figure 14 compares the angular rangeand the amplitude of light intensity for CPTCs. The couplerwas designed for a fiber with a numerical aperture (NA) of0.48, which means that the maximum acceptable cone angleof the fiber should be 56โ. The simulated results for angularrange demonstrate the validity of the calculations for thedesigned coupler. As shown in Figure 13, all CTPCs aroundcenter one have less uniform distribution of intensity. Hence,the center CTPC could be used for electricity generation via
multijunction solar cells due to its uniform intensity andsmall angular range of radiation, that is, less than 30
โ (SeeFigure 14). The uniformity for other CTPCs that are usedfor lighting could be increased by grouping the fiber opticsaccording to their intensity and by combining the sunlightand the LED light with a hybrid luminaire.
5. Conclusion
In this study, a newdesign of coupler formultifunctional solarapplications was presented. This design includes a plate (flator carved) and nine CTPCs. The shape of CTPCs providedan easy connection between the fiber and the coupler, suchthat there was no space in the assembly of CTPCs on theplate surface. Also, the coupler could be connected to a high-concentration parabolic dish and fiber optics while beingused as a secondary concentrator. The theory for designingand modeling CTPCs, as well as the related mathematicalequations for the coupler structure, has been developed. Sim-ulation of the proposed coupler showed 92% efficiency, andthe rim angle of the parabolic dish wasmaintained at 45โ.Theobtained results indicate that the peak of radiant intensity andthe total power of the corner CTPCs noticeably decrease the
10 International Journal of Photoenergy
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0.9111
1 1 1
111
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
30
6090
120
150
180
โ150
โ120โ90
โ60
โ30
0
30
6090
120
150
180
โ150
โ120โ90
โ60
โ30
0
30
60
90120
150
180
โ150
โ120โ90
โ60
โ30
0
30
6090
120
150
180
โ150
โ120โ90
โ60
โ30
0
30
6090
120
150
180
โ150
โ120โ90
โ60
โ30
0
30
6090
120
150
180
โ150
โ120โ90
โ60
โ30
0
30
6090
120
150
180
โ150
โ120โ90
โ60
โ30
0
30
6090
120
150
180
โ150
โ120โ90
โ60
โ30
0
30
6090
120
150
180
โ150
โ120โ90
โ60
โ30
Figure 14: Distribution of angular range and amplitude for CTPCs according to their position.
amplitude of power intensity. The simulated results confirmthat the central CTPC is appropriate for generating electricpower using multijunction solar cells; the CTPCs located atthe side of the plate are suitable for producing heat, whereasthose at the corners can be used to provide daylighting.
Competing Interests
The authors declare that they have no competing interests.
Acknowledgments
This work has been supported by the University of Malayaunder the High Impact Research (Grant no. UM.0000005/HIR.C1), theUMRG (Grant no. RP021A-13AET), and the PPP(Grant no. PG218-2015A).The authorswould like to thankDr.
Mohd Haniff Ibrahim from the photonics lab and UniversitiTeknologi Malaysia for providing access to Zemax software.
References
[1] S. Pless and P. Torcellini, Net-Zero Energy Buildings: A Classifi-cation System Based on Renewable Energy Supply Options, 2010.
[2] G. Mittelman, A. Kribus, and A. Dayan, โSolar cooling withconcentrating photovoltaic/thermal (CPVT) systems,โ EnergyConversion andManagement, vol. 48, no. 9, pp. 2481โ2490, 2007.
[3] J. M. Cariou, J. Dugas, and L.Martin, โTransport of solar energywith optical fibres,โ Solar Energy, vol. 29, no. 5, pp. 397โ406,1982.
[4] W. Grise and C. Patrick, โPassive solar lighting using fiberoptics,โ Journal of Industrial Technology, vol. 19, no. 1, pp. 1โ7,2002.
International Journal of Photoenergy 11
[5] D. Feuermann and J. M. Gordon, โSolar surgery: remote fiberoptic irradiation with highly concentrated sunlight in lieu oflasers,โ Optical Engineering, vol. 37, no. 10, pp. 2760โ2767, 1998.
[6] S. Amara,Novel and ancient technologies for heating and coolingbuildings [Ph.D. thesis], 2011.
[7] C. Zidani, B. Benyoucef, and N. Madini, โOptimization ofphotothermal system based on the idea of transmission solarenergy via optical fibres,โ Physics Procedia, vol. 55, pp. 493โ502, 2014, Proceedings of the 8th International Conference onMaterial Sciences, CSM8-ISM5.
[8] A. Kribus, O. Zik, and J. Karni, โOptical fibers and solar powergeneration,โ Solar Energy, vol. 68, no. 5, pp. 405โ416, 2000.
[9] F. C. Christo, โNumerical modelling of wind and dust patternsaround a full-scale paraboloidal solar dish,โ Renewable Energy,vol. 39, no. 1, pp. 356โ366, 2012.
[10] C. Kandilli, K. Ulgen, and A. Hepbasli, โExergetic assessmentof transmission concentrated solar energy systems via opticalfibres for building applications,โ Energy and Buildings, vol. 40,no. 8, pp. 1505โ1512, 2008.
[11] T. Nakamura, B. Comaskey, and M. Bell, โDevelopment ofoptical components for space-based solar power system forISRU and regnerative life support,โ in Proceedings of the 40thAIAA Aerospace Sciences Meeting and Exhibit, January 2002.
[12] D. Feuermann and J.M. Gordon, โSolar fiber-opticmini-dishes:a new approach to the efficient collection of sunlight,โ SolarEnergy, vol. 65, no. 3, pp. 159โ170, 1999.
[13] A. L. Luque and A. Viacheslav, Concentrator Photovoltaics,vol. 130 of Springer Series in Optical Sciences, Springer, Berlin,Heidelberg, 2007.
[14] K. Lovegrove, G. Burgess, and J. Pye, โA new 500m2 para-boloidal dish solar concentrator,โ Solar Energy, vol. 85, no. 4, pp.620โ626, 2011.
[15] L. Li and S. Dubowsky, โA new design approach for solar con-centrating parabolic dish based on optimized flexible petals,โMechanism and Machine Theory, vol. 46, no. 10, pp. 1536โ1548,2011.
[16] X.-L. Xia, G.-L. Dai, and Y. Shuai, โExperimental and numericalinvestigation on solar concentrating characteristics of a sixteen-dish concentrator,โ International Journal of Hydrogen Energy,vol. 37, no. 24, pp. 18694โ18703, 2012.
[17] C. Ciamberlini, F. Francini, G. Longobardi, M. Piattelli, and P.Sansoni, โSolar system for exploitation of the whole collectedenergy,โOptics and Lasers in Engineering, vol. 39, no. 2, pp. 233โ246, 2003.
[18] M. A. Soderstrand, S. B. Lee, and P. Chung, โMini-dish basedhybrid Concentrated Solar Power (CSP) system for homeuse,โ in Proceedings of the IEEE 56th International MidwestSymposium on Circuits and Systems (MWSCAS โ13), pp. 689โ692, Columbus, Ohio, USA, August 2013.
[19] D. Liang, L. Fraser Monteiro, M. Ribau Teixeira, M. L. FraserMonteiro, and M. Collares-Pereira, โFiber-optic solar energytransmission and concentration,โ Solar Energy Materials andSolar Cells, vol. 54, no. 1โ4, pp. 323โ331, 1998.
[20] R. Winston and E. Ning, Nonimaging Radiant Energy Device,1996.
[21] D. Feuermann, J. M. Gordon, and M. Huleihil, โSolar fiber-optic mini-dish concentrators: first experimental results andfield experience,โ Solar Energy, vol. 72, no. 6, pp. 459โ472, 2002.
[22] K. He, H. Zheng, Z. Li, Taotao, and J. Dai, โDesign and inves-tigation of a novel concentrator used in solar fiber lamp,โ SolarEnergy, vol. 83, no. 11, pp. 2086โ2091, 2009.
[23] I. Ullah and S. Shin, โHighly concentrated optical fiber-baseddaylighting systems formulti-floor office buildings,โ Energy andBuildings, vol. 72, pp. 246โ261, 2014.
[24] X. Yu, Y. Su, H. Zheng, and S. Riffat, โA study on use ofminiature dielectric compound parabolic concentrator (dCPC)for daylighting control application,โ Building and Environment,vol. 74, pp. 75โ85, 2014.
[25] G. E. Arnaoutakis, J. Marques-Hueso, T. K. Mallick, and B. S.Richards, โCoupling of sunlight into optical fibres and spectraldependence for solar energy applications,โ Solar Energy, vol. 93,pp. 235โ243, 2013.
[26] A. Rabl, โComparison of solar concentrators,โ Solar Energy, vol.18, no. 2, pp. 93โ111, 1976.
[27] A. Rabl, Active Solar Collectors and Their Applications, OxfordUniversity Press, 1985.
[28] D. E. Williamson, โCone channel condenser optics,โ Journal ofthe Optical Society of America, vol. 42, no. 10, pp. 712โ714, 1952.
[29] W. Witte, โCone channel optics,โ Infrared Physics, vol. 5, no. 4,pp. 179โ185, 1965.
[30] J. H. Myer, โCollimated radiation in conical light guides,โApplied Optics, vol. 19, no. 18, pp. 3121โ3123, 1980.
[31] American Society for Testing and Materials (ASTM), โRefer-ence solar spectral irradiance,โ ASTM G 173-03, NREL, 2012.
[32] M. Polyanskiy, โRefractive index database,โ http://refractivein-dex.info.
[33] D. Feuermann, J. M. Gordon, and M. Huleihil, โLight leakagein optical fibers: experimental results, modeling and the conse-quences for solar concentrators,โ Solar Energy, vol. 72, no. 3, pp.195โ204, 2002.
Submit your manuscripts athttp://www.hindawi.com
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Inorganic ChemistryInternational Journal of
Hindawi Publishing Corporation http://www.hindawi.com Volume 2014
International Journal ofPhotoenergy
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Carbohydrate Chemistry
International Journal of
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Journal of
Chemistry
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Advances in
Physical Chemistry
Hindawi Publishing Corporationhttp://www.hindawi.com
Analytical Methods in Chemistry
Journal of
Volume 2014
Bioinorganic Chemistry and ApplicationsHindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
SpectroscopyInternational Journal of
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
The Scientific World JournalHindawi Publishing Corporation http://www.hindawi.com Volume 2014
Medicinal ChemistryInternational Journal of
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Chromatography Research International
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Applied ChemistryJournal of
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Theoretical ChemistryJournal of
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Journal of
Spectroscopy
Analytical ChemistryInternational Journal of
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Journal of
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Quantum Chemistry
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Organic Chemistry International
ElectrochemistryInternational Journal of
Hindawi Publishing Corporation http://www.hindawi.com Volume 2014
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
CatalystsJournal of