Digital Signal Processing
for
HPGe Detectors
July 28, 2012
David Radford ORNL Physics Division
2 Managed by UT-Battelle for the U.S. Department of Energy
• Hyper-Pure Ge (HPGe) detectors are the “gold standard” for gamma-ray spectroscopy − Unsurpassed energy resolution
− Indispensible to in-beam nuclear structure studies for many decades
• Made from a single large crystal pulled from molten hyper-pure Ge • Operated as a large reverse-biased diode; up to 5 kV bias
• No current flows until a gamma ray interacts with an electron in the Ge, lifting its energy above the band gap of the Ge semiconductor
• This electron scatters off other electrons, creating many electron-hole pairs; each pair takes ~ 3 eV in energy
• The electrons and holes separate in the strong electric field and are collected at the electrodes
• The resulting charge pulse is proportional to the deposited gamma-ray energy, and is amplified and digitized
• Operated at cryogenic temperatures to prevent thermal generation of electron-hole pairs
HPGe Detectors
3 Managed by UT-Battelle for the U.S. Department of Energy
Closed-end coaxial
n+
p+ p
n+
p
Planar
HPGe Detectors Historically, there have been two designs, both cylindrical:
Coaxial and Planar.
Later we will discuss a new design, “Point Contact” detectors
p+
4 Managed by UT-Battelle for the U.S. Department of Energy
Closed-end coaxial
n+
p+ p
n+
p
Planar
HPGe Detectors Historically, there have been two designs, both cylindrical:
Coaxial and Planar.
p+
~ 3 kV
−
+
5 Managed by UT-Battelle for the U.S. Department of Energy
HPGe Detectors
Electric potential
Drift paths of electrons and holes
Closed-end coaxial
Fast ADC Charge-integrating pre-amp
Signal Processing
Once the preamplifier signal/waveform has been digitized, need to process the data to extract interesting numbers, e.g. • Amplitude
• Gives energy, so we want it to be as accurate as possible
• Timing • Pulse-shape analysis to select specific types of
events • Noise filtering and/or reduction • Pile-up rejection and/or correction
Extracting Signal Amplitude
Height of signal is proportional to
detected energy
Preamp signal • Decays exponentially with
~ 50µs time constant
Time
Volta
ge
Extracting Signal Amplitude
But the signal has noise… • Need to integrate signal for several microseconds
to determine amplitude more precisely • Use “Trapezoid Filter”
Extracting Signal Amplitude
Output of Trapezoid Filter
Undershoot due to exponential decay of signal
Extracting Signal Amplitude
• Need to correct for signal decay time • “Pole-zero” correction
Trapezoid and P/Z Correction • Need to know the baseline (asymptote)
and signal decay time constant tau • E ~ S2’ – S1’
Baseline
S1’
S2 S2’
S1
14 Managed by UT-Battelle for the U.S. Department of Energy
P-type Coaxial P-type Point Contact
p p+
n+ n+
p+
p
Point Contact Detectors • No deep hole; small point-like central contact • Length is shorter than standard coaxial detector • Excellent discrimination between single-interaction and multiple-
interaction events • Excellent resolution at low energies
Pulse-Shape Response Point Contact detectors are ideal for discrimination between single-site and multi-site events (or determining the number of interactions)
0
100
200
300C
harg
e Si
gnal
0
20
40
60
Cur
rent
Sig
nal
200 600 1000 1400Time (ns)
0
100
200
300
400
0
20
40
60
80
200 600 1000 1400Time (ns)
a) Single-site b) Multi-site
16 Managed by UT-Battelle for the U.S. Department of Energy
Pulse-Shape Response
9/30/09 Radford, RedTeam Review
Red: all events Blue: PSA-selected events
Th source
95% efficiency for double-escape peak = single-site events 99% rejection of single-escape peak = multi-site events
17 Managed by UT-Battelle for the U.S. Department of Energy
“Inverted-Coaxial” Point-Contact Detector • Designed and developed here at ORNL • Drift of charges is radically different from a normal coaxial detector • Very long drift times, ~ 2 µs • A segmented prototype has recently been produced by Canberra France
19 Managed by UT-Battelle for the U.S. Department of Energy
Am “SuperPulses” • Finely collimated Am source,
directed at known location on the detector surface
• Select events with 60 keV in a single hit segment
• Use PSA to select only single-site events
• Time-align events to a common time
• Take average signal to reduce noise to negligible level
RadWaresig2sp.ps, created 08-Apr-13 03:18:08
Cha
rge
1 1 1 10 2 2 2 2Time ( s)
Superpulse
Singleevent
PC Seg1 Seg2 Seg3