Int. J. Electrochem. Sci., 9 (2014) 3864 - 3875
International Journal of
ELECTROCHEMICAL SCIENCE
www.electrochemsci.org
Impedance Spectroscopy and Dielectric Properties of Silver
Incorporated Indium Sulfide Thin Films
Nurdan Demirci Sankır*, Erkan Aydın, Mehmet Sankır
Department of Materials Science and Nanotechnology Engineering, TOBB University of Economics
and Technology, Ankara, Turkey *E-mail: [email protected]
Received: 2 March 2014 / Accepted: 20 March 2014 / Published: 14 April 2014
In this study, silver incorporated indium sulfide (In2S3) thin films have been deposited on soda lime
glass via spray pyrolysis technique. Structural and electrical properties have been tailored by adding
controlled amount of silver acetate into the precursor solution. A phase shift form cubic -In2S3 to
AgInS2 has been evidenced from X-ray diffraction spectra (XRD). Molecularity of the samples,
meaning (Ag+In)/S ratio, has directly affected the electrical conductivity as well as the dielectric
properties. Direct and alternating current conductivities increased with increasing the (Ag+In)/S ratio
upto 10% silver incorporation. When the silver amount further increased conductivity decreased due to
the pronounced secondary phase formation. The complex impedance analysis was used to determine
the effect of silver on the conduction mechanism. It has been observed that frequency exponent of all
samples were greater than unity indicating the nanocrystalline nature of the films. The variation of
dielectric properties and ac conductivity with frequency revealed that the relaxation process in silver
incorporated In2S3 thin films was due to the Maxwell–Wagner type of interfacial polarization in
general.
Keywords: Spray pyrolysis, indium sulfide, silver incorporation, impedance spectroscopy, dielectric
properties
1. INTRODUCTION
Indium sulfide (In2S3) is a promising material for optoelectronic and photovoltaic applications
due to its proper band gap energy, stability and photoconductive nature 1. Thin films of In2S3 have
also been gaining more attention as a non-toxic and effective alternative of the cadmium sulfide most
commonly used n-type semiconductor for commercial solar cells 2. Various manufacturing
techniques have been used to deposit In2S3 thin films such as atomic layer deposition, close space
evaporation, electrodeposition, chemical bath deposition, spray-ILGAR, and spray pyrolysis [3-8]. Wet
chemical techniques have the advantages of low manufacturing cost, ease of scalability over large
Int. J. Electrochem. Sci., Vol. 9, 2014
3865
areas and compatibility with various substrates including plastic and even paper. Recently B. Mari et
al. reported the electrochemical deposition of the In2S3 using an organic solvent, which had the
advantages of high boiling point, dielectric constant that allows the solubility of salts and chalcogen
precursors in elemental state 9. In this study, due to its simplicity and very high manufacturing speed
spray pyrolysis technique was used to build In2S3 thin films. Moreover, this technique does not require
expensive solid sources and offers very low solution consumption for large area manufacturing, which
are the key factors for the commercialization in the solar cell area. Doping of functional thin films,
which is an effective way of tailoring electrical, structural and optical properties, can be easily done by
adding the salt of desired element during the spray process. Although, there are numerous works on
doping of spray-pyrolyzed oxides such as zinc oxide, nickel oxide and titanium dioxide in literature,
there are very limited studies on doping of spray pyrolyzed In2S3 thin films 10-13. Previously, M.
Mathew et al. reported the zinc incorporation of the indium sulfide thin films deposited via spray
pyrolysis 13. They claimed that tin doping modified the band gap and electrical properties of the
In2S3 films favorably over wider ranges making these films suitable for optoelectronic applications.
Here, we investigated the structural, optical, electrochemical and dielectric properties of the silver
doped spray-pyrolyzed In2S3 thin films. According to our best knowledge, this is the first report on
effects of silver incorporation on the impedance spectroscopy and dielectric properties of spray
pyrolyzed In2S3 thin films.
2. EXPERIMENTAL
Silver incorporated In2S3 thin films were prepared on soda lime glass using SonoTek FlexiCoat
USP coating system. Indium (III) chloride (InCl3, Sigma-Aldrich), and thiourea (NH2CSNH2, Sigma-
Aldrich) were used as indium and sulfur source, respectively. Silver incorporation was done by adding
silver acetate (Ag(CH3COO), Merck) to the precursor solution at various molarities. Detailed
information about the spray pyrolysis system and the silver incorporation was reported in our previous
studies [14-16]. The surface morphology of the films was investigated by FEI, Quanta 200 FEG SEM.
EDX microanalysis has been used to evaluate the chemical compositions of the films. The optical
transmittance spectra of the samples were measured by a Perkin Elmer 600 S UV–VIS
spectrophotometer in wavelength range of 200-800 nm. Room temperature AC conductivity of the
films was performed using Solartron SI 1260 Impedance/Gain-Phase Analyzer equipped with a 1296
Dielectric Interface. Impedance data were taken in dark conditions at room temperature using the AC
modulation voltage of 500 mV at 1 Hz -1 MHz frequency range. Data fitting and analysis of the
electrical impedance measurements were done using Z-View software (Scribner Associates).
3. RESULTS AND DISSCUSSIONS
3.1. Structural and Optical Properties
In order to investigate the effect of silver incorporation on the film properties, various amounts
of silver acetate have been added into the precursor solution. 10 mM of indium concentration was kept
Int. J. Electrochem. Sci., Vol. 9, 2014
3866
constant for all experiments, which was assumed as 100 %. Then, silver to indium molar ratio
([Ag]:[In]) was defined as percent silver concentration of indium concentration. Figure 1 depicts the
SEM images of the silver incorporated In2S3 thin films. As can be seen in this figure, all of our films
were homogenous and crack free. Moreover, silver addition did not affect the surface morphology of
spray-pyrolyzed In2S3 thin films. EDX analysis, carried out at accelerating voltage of 15 kV and spot
size 3μm, has been performed to determine the chemical composition of the In2S3 thin films.
Figure 1. SEM micrographs of in-situ Ag doped In2S3 films.
As targeted, the silver amount in the films increased with increasing the molarity of the silver
acetate. Figure 2 (b) shows the variation of the elements in atomic percent determined from EDX
analysis for various silver concentrations. It has been observed that sulfur atomic percent in the films
did not changed drastically with silver incorporation. On the other hand, indium percent decreased
while silver percent in the films increased. This indicated the possibility of sitting of the silver atom in
the cationic sites of In2S3 structure. Silver incorporation to the films was also detected from the visual
appearance of the films. As can be seen in Figure 2 (a), color of the films was changed from light
yellow to orange in daylight with silver incorporation. Besides, the atomic ratio of (Ag+In)/S for all
samples have been calculated using EDX results and listed in Table 1. Although there were some
fluctuations, (Ag+In)/S ratio increased with increasing the silver concentration in the precursor
solution. This ratio can be an indication of phase shift towards In2S3 to AgInS2. Also the total ratio of
metals to sulfur in the films may effect the electrical conduction. Besides, EDX analysis confirmed the
chlorine contamination most probably from the usage of chlorine based salts as precursor chemical
(Fig. 2(b)). The chlorine percent in the films increased from 10.1 to 11.5 at. % with increasing the
silver concentration. This was a strong indication of formation of chlorine and silver based secondary
phases with increasing the [Ag]:[In].
Int. J. Electrochem. Sci., Vol. 9, 2014
3867
(a) (b)
Figure 2. (a) Visual appearance and (b) atomic ratios of silver incorporated In2S3 films
Table 1. Mean crystallite size, band gap and dc conductivity of the silver incorporated In2S3 thin films
[Ag+]:[In
3+]
(%)
(Ag+In)/S
Mean
Crystallite
Size (nm)
Band
Gap
(eV)
0.5 0.74 40 2.75
1 0.68 30 2.76
5 0.77 46 2.76
10 0.75 44 2.70
20 0.87 44 2.66
Crystal structure of the films has been confirmed via X-ray diffraction analysis. Figure 3 shows
the XRD patterns of the samples with various silver concentrations. Quantitative analysis of these
patterns showed that the major phase for all our samples was cubic -In2S3 (JCPDS Card No. 32-456).
The intensity of the peak around 33° (2), could be attributed to the (200) cubic plane, decreased with
increasing the silver incorporation. Secondary most intense peak for all samples was located around
28° (2) which could be attributed to both (311) cubic -In2S3 or orthorhombic AgInS2 [17, 18].
Therefore, it is possible to mention about a phase shift from cubic -In2S3 to orthorhombic AgInS2
with silver addition. The presence of AgCl crystals was also confirmed from XRD data (JCPDS file
no.: 31-1238). The peaks observed around 28, 33, 47° (2θ) could be assigned to both AgCl and cubic
In2S3 structure.
Int. J. Electrochem. Sci., Vol. 9, 2014
3868
Spray deposited In2S3 films consist of small nano scale crystallites and this probably triggers
the formation of secondary phases, which have different compositions. The detailed structural analysis
of silver incorporated In2S3 thin films have been reported in our previous work [16]. Mean crystallite
size has been calculated using Scherrer’s formula with 0.89 correction factor. As summarized in Table
1 all of our films were in nanocrystalline nature. Previously similar crystallite sizes have been reported
for the wet chemical deposition of In2S3 thin films [13].
Figure 3. XRD spectra of In2S3 thin films with various silver incorporation
Figure 4. Absorbance versus wavelength spectra of the silver doped In2S3 thin film.
Int. J. Electrochem. Sci., Vol. 9, 2014
3869
Optical properties of the silver incorporated In2S3 has been observed form the UV-VIS spectra
of the thin films (Fig. 4). The absorbance of thin films increased with silver addition. As can bee seen
in Table 1, band gap energies of the films, which have been calculated using the UV-VIS data,
decreased from 2.75 to 2.66 eV by silver addition. All these values were proper for using these films as
the window layer for solar cell applications. It can also be concluded that the in-situ silver doping
could be used to tailor the optical properties of the In2S3 films.
3.2 Impedance Spectroscopy
Frequency dependent electrical conductivity measurements of the silver incorporated In2S3 thin
films have been performed at room temperature, under dark and in the frequency range of 1Hz-1 MHz.
Frequency dependant impedance data have been recorded using Solartron SI 1260 Impedance/Gain-
Phase Analyzer equipped with a 1296 Dielectric Interface. Figure 5 shows the Nyquist plots of our
samples. For all samples single semicircle fit was observed indicating the single relaxation process.
Equivalent circuit can also be seen in inset Figure 5. Circuit parameters have been calculated from the
fitting values obtained via Z-View software and summarized in Table 2. As expected, Rs value which
indicates the contact resistances were comparable for all of our samples and were in the range of kilo
ohm. The bulk resistances of the samples (Rp) were in consistent with conductivity of the films and as
a general trend decreased with increasing the (Ag+In)/S ratio in the films. As can be also seen in Table
2, there was no significant change in capacitance with silver incorporation. Cp of the samples was
around 1.5 pF for all samples. Bode and phase angle diagrams of the silver doped In2S3 thin films can
bee seen in Figure 5.
Figure 5. Nyquist plots of silver incorporated In2S3 films for various [Ag]:[In] concentrations in
solution.
The analysis of Bode plots (Fig. 6) gave information complementary to the one obtained from
Nyquist plots. One time constant behavior can be also seen in these diagrams. Moreover, samples
having more silver showed higher capacitive arc.
Int. J. Electrochem. Sci., Vol. 9, 2014
3870
Table 2. Direct current (dc) conductivity and equivalent circuit parameters of
[Ag]:[In] (%) σdc (S/cm) Rs (Ω) Rp (Ω) Cp (F)
0.5 1.5x10-5
8x103 1.2x10
9 1.6x10
-12
1 0.6x10-5
8x103 1.6x10
10 1.6x10
-12
5 2.8x10-5
8x103 0.7x10
9 1.4x10
-12
10 1.6x10-5
7x103 1.1x10
9 1.7x10
-12
20 0.7x10-5
7x103 3.9x10
9 1.6x10
-12
Figure 6 also reveals that parallel R-C circuit can used to explain alternating current
measurements of our samples. We observed one plateau at low frequencies in logZ versus logf plots
and two plateaus in phase angle graphs due to relatively very small Rs compare to the Rp. Furthermore,
the resistance values can be observed from low frequency intercept in Bode plots were consistent with
the conductivity of our thin films.
(a) (b)
Figure 6. (a) Bode and (b) phase angle graphs of silver doped In2S3 thin films
The electrical conductivity σ(ω) of the silver incorporated In2S3 thin films at a particular
temperature over a frequency range can be written in the combination of DC and AC part;
() dc As (1)
where σdc is the DC part of the electrical conductivity, A is the temperature dependant constant
and s is the frequency exponent. Figure 7 shows the change in σac with frequency. For all samples, the
conductivity increases sharply with frequency showing a distinct change in slope. This linear region at
Int. J. Electrochem. Sci., Vol. 9, 2014
3871
ln σac versus lnω graphs started at different cut-off frequencies, which was in the range of 400-800 Hz.
Below and under these limits, conductivity stayed constant. Stability of the conductivity can be
attributed to the free charge formation in the film. Moreover, the increase in the conductivity with
frequency could be a sign of release of trapped charges in the disorder system. This is consisted with
the nanocrystalline nature of spray-pyrolyzed films. It was also observed that AC conductivity of the
silver incorporated films were comparable with each other. The frequency exponent “s” of the silver
incorporated In2S3 thin films have been calculated using the slope of ln σac versus lnω plots. “s” is
roughly treated as constant less than 1 and often used to describe the ac component contributing to the
dispersive region 19. In our study “s” is greater than unity and decreasing from 1.9 to 1.5 by
increasing the silver amount. It has been known that “s” can hold value greater than unity in some
mixed compounds, like (NH4)3H(SO4)1.42(SeO4)0.58 and polymeric networks 20, 21. This high “s”
value most probably was due to the distribution of accessible conduction paths stemming from the
absence of periodicity in space and the presence of defects 21.
Figure 7. Frequency dependence of ac of In2S3 films for different [Ag+]:[In
3+] concentrations in
solution.
3.3 Dielectric Properties
The frequency dependence of the dielectric permitivity (ε’) of silver incorporated In2S3 thin
films at room temperature can be seen in Figure 8. It has been observed that all of the samples
exhibited relatively high dielectric permitivity at low frequencies and it decreased with increasing the
frequency. In the high frequency range dielectric constant were independent of silver amount and
frequency. Previously M. A. M. Seyam has reported a similar behavior for the In2S3 thin films
deposited via thermal evaporation method 22.
Int. J. Electrochem. Sci., Vol. 9, 2014
3872
The decrease in dielectric permitivity with frequency can be attributed to the contribution of the
multicomponent polarizability, which are deformational and relaxation. Deformational polarizability is
the mutual displacement of the oppositely charged partciles under the action of applied field. On the
other hand, the relaxation plorizability originated from limited mobility of the permenant dipoles
shows up at lower frequencies. In other words, as the frequency increased dipoles will no longer be
able to rotate sufficiently, so that their oscillation will begin to lag behind those of the field. Hence
dielectric constant at high frequencies approaches a limit value 23.
Figure 8. log()- plots of in-situ Ag doped In2S3 films for different [Ag+]:[In
3+] concentrations in
solution.
The electrical modulus (M), which is defined as the reciprocal of the complex relative
permittivity, can be used to understand electrical relaxation processes. M corresponds to the relaxation
of the electric field in the material when the electric displacement remains constant 24. Figure 9
shows the variation of the real and imaginary part of electrical modulus as a function of logarithmic
angular frequency, which can be calculated using the following equations;
M* 1
* M ' jM ''
(2)
The real and the imaginary part of M* are given as;
M ' '
' 2 '' 2
M '' ''
' 2 '' 2
(3)
Int. J. Electrochem. Sci., Vol. 9, 2014
3873
At relatively lower frequencies M’ tends to be constant for all samples. Also, similar behavior
has been observed at the high frequencies. Figure 9 (b) depicts an asymetric behavior with respect to a
peak maxima, whose positions were frequency dependent. Moreover maxima of M’’ shifted through
higher frequencies with increasing the (Ag+In)/S ratio upto 20% silver loading. For the 20% [Ag]:[In]
sample, M’’
max shifted back. The analomoous behavior of 20% silver contaning films could be
attributed to the crystal phase shift confirmed by XRD analysis. Combined with the dielectric
permitivity results it is possible to explain the relaxation process in silver doped In2S3 thin films with
Maxwell-Wagner polarization. This theorem has been used to explain the effect of large grain
boundaries on the electrical conduction mechanism 25. In this model, the dielectric materials with
heterogenic structure are assumed as the systems consisting of conducting grains separated by the
resistive grain boundaries. Therefore the grain boundary volume controls the behavior of ε′ at low
frequencies. The higher values of dielectric permitivity at low frequencies can be explained on the
basis of interfacial space charge polarization due to inhomogeneous dielectric structure.
Figure 9. Modulus plots of in-situ Ag doped In2S3 films for different [Ag
+]:[In
3+] concentrations in
solution.
4. CONCLUSIONS
With this study for the first time it has been proved that dc and ac electrical properties of spray
pyrolyzed In2S3 thin films can be tailored via very simple in-situ silver incorporation. In2S3 thin films
have been deposited soda lime glass at various silver concentrations. EDX results showed that silver
amount in the films was increased with increasing the silver concentration in the precursor solution.
Optical absorption of the films increased with increasing the silver concentration and therefore band
gap energy decreased. Although the silver atomic percent in the films increased with silver
concentration (Ag+In)/S ratio fluctuated. This ratio was directly effected the dc conductivity and the
all other electrical properties upto 10%. After that point, conductivity of the samples decreased most
probably due to the secondary phase formations in the films. XRD analysis revealed that main crystal
Int. J. Electrochem. Sci., Vol. 9, 2014
3874
structure of all samples was cubic -In2S3. Also all films were in nanocrystalline nature. Secondary
phases such as AgInS2 and AgCl have been observed with increased silver amount. XRD analysis
combined with EDX results indicated that AgCl phase became pronounced with increasing the silver
concentration. This directly affected the electrical properties. In other words, both ac and dc
conductivity of the films decreased when the silver incorporation increased to 20%. This also affected
the dielectric properties such as dielectric permitivity, modulus and tangent loss. Two different
frequency dependencies of dielectric constant at low and high frequency range and also asymmetric
modulus behavior indicated that relaxation process in silver doped In2S3 thin films can be explained
with Maxwell-Wagner polarization.
ACKNOWLEDGEMENTS
This study was supported by Republic of Turkey Ministry of Science, Industry and Technology under
the research Grant 01072.STZ.2011-2.
References
1. . Asen o, C. Sanz, C. uill n, A.M. Chaparro, M.T. uti rrez, J. Herrero, Thin Solid Films, 515
(2007) 6041
2. N. Barreau, Sol. Energy 83 (2009) 363
3. S. Spiering, D. Hariskos, M. Powalla, N. Naghavi, D. Lincot, Thin Solid Films, 431–432 (2003)
359
4. N. Revathi, P. Prathap, K.T. Ramakrishna Reddy, Solid State Sci. 11 (2009) 1288
5. M. Abdel Haleem, M. Ichimura, Thin Solid Films, 516 (2008) 7783
6. C.D. Lokhande, A. Ennaoui, P.S. Patil, M. Giersig, K. Diesner, M. Muller, H. Tributsch, Thin Solid
Films, 340 (1999) 18
7. N. A. Allsop, A. Schonmann, H.-J. Muffler, M. Bar, M. C. Lux-Steiner, Ch.-H. Fischer, Prog.
Photovolt: Res. Appl. 13 (2005) 607
8. S. uecheler, D. Corica, D. uettler, A. Chirila, R. Verma, U. Müller, T.P. Niesen, J. Palm, A.N.
Tiwari, Thin Solid Films, 517 (2009) 2312
9. B. Mari, M. Mollar, D. Soro, R.Henriquez, R. Schrebler, H. Gomez, Int. J. Electrochem. Sci., 8
(2013) 3510
10. M. Mathew, M. Gopinath, C. S. Kartha, K. P.Vijayakumar, Y. Kashiwaba, T. Abe, Sol. Energy, 84
(2010) 888
11. J-H. Lee, B-O. Park, Mater. Sci. Eng. B-Adv., 106 (2004) 242
12. P. Puspharajah, S. Radhakrishna, A. K Arof, J. Mater. Sci., 32 (1997) 3001
13. H. Yanagi, Y. Ohoka, T. Hishiki, K. Ajito, A. Fujishima, Appl. Surf. Sci., 113-114 (1997) 426
14. E. Aydin, N.D. Sankir, J. Opt. Adv. Mater., 15 (2013) 14
15. N.D. Sankir, E. Aydin, H. Unver, E. Uluer, M. Parlak, Sol. Energy 95 (2013) 21
16. E. Aydin, M. Sankir, N. D. Sankir, Submitted to J. Alloy. Compd. (2014)
17. T.T. John, C.S. Kartha, K.P. Vijayakumar, T. Abe, Y. Kashiwaba, Appl. Surf. Sci., 252 (2005)
1360
18. S. Lugo, Y. Pena, M. Calixto-Rodriguez, C. López-Mata, M.L. Ramón, I. ómez, A. Acosta, App.
Surf. Sci. 263 (2012) 440
19. N.F. Mott, E.A. Davis, Electronic Processes in Non-Crystalline Materials, Clarendon Press,
Oxford (1979)
20. B. Louati, M. Gargouri, K. Guidara, and T. Mhiri, J. Phys. Chem. Solids 66 (2005) 762
Int. J. Electrochem. Sci., Vol. 9, 2014
3875
21. A. N. Papathanassiou, I. Sakellis, J. Grammatikakis, Appl. Phys. Lett., 91 (2007) 122911
22. M. A. M. Seyam, A.E. Bekheet, A. Elfalaky, Eur. Phys. J. AP 16 (2001) 99
23. F. Carpi, D. D. Rossi, R. Kornbluh, R. Pelrine, P. Sommer-Larsen, Dielectric Elastomers as
Electromechanical Transducers, Elsevier, Hungary (2008)
24. S.R. Elliott, J. Non-Cryst. Solids, 170 (1994) 97
25. J.C. Maxwell, Treaties on Electricity and Magnetism, Clarendon, Oxford (1892)
© 2014 The Authors. Published by ES (www.electrochemsci.org). This article is an open access
article distributed under the terms and conditions of the Creative Commons Attribution license
(http://creativecommons.org/licenses/by/4.0/).