Stump Harvesting
Dana Mitchell, Research Engineer, USDA Forest Service, Southern Research Station,
521 Devall Drive, Auburn, AL, USA, [email protected], 334 826-8700
Abstract
Increased use of forest fuel requires larger and larger procurement areas. Inclusion of stump
material within the shorter distances could make this unusual source of biomass more
economical to harvest. Land clearing activities are also helping to raise interest in stump
harvesting. Processing stump material for biomass is an alternative to other, more costly, woody
waste disposal alternatives. This paper reviews some of the existing research regarding
harvesting equipment and systems, feedstock quality, and identifies environmental
considerations related to the practice of stump harvesting.
Introduction
Stumps are a source of woody biomass, but stump harvesting is not a common practice in the
United States. Stumps are often lifted, or pushed over, in land clearing operations prior to new
residential or commercial construction. The cost associated with pushing up stumps, piling
stumps and debris, and burning is often regarded as normal pre-construction activity. However,
due to burning restrictions, some construction contractors are forced to find alternative means for
removing stumps from work sites. Some are sub-contracting to logging contractors for stump
removal services. In addition to receiving service contract payments for removals, the logging
contractors may also comminute and sell the biomass that is produced.
Stump and root mass harvesting may seem like a very strange and costly way to obtain biomass.
Transportation costs would be high because the odd-shaped pieces, with main root masses
attached, would not compact well. Some type of communition in the woods is needed to reduce
the size of the pieces, thus increasing payloads for transport. Splitting may help in breaking the
material up to facilitate larger payloads for in-woods transport.
Different comminution equipment may be needed based on the physical characteristics of the
root masses. Oversized root masses may be too large to fit into the throat of a horizontal grinder
without pre-processing. Disc chippers would be difficult to use because most do not have a
horizontal conveyor in-feed. Tub grinders have historically been used to process stumps. Some
stump harvesting systems may require stump splitting as a pre-processing step prior to
comminution with a traditional grinder or horizontal-feed chipper.
The delivered value of the biomass material from stumps must be high enough to pay for the cost
of processing and transport. In addition, the comminuted material may have high levels of
contaminants such as soil and rocks. The feedstock quality can impact the delivered price and it
can also limit the biomass delivery locations to those purchasers who can accept some impurities
in their handing systems and conversion processes. This review of stump harvesting examines
the harvesting systems and equipment, feedstock quality, and identifies environmental
considerations related to the practice of stump harvesting.
Harvesting Systems and Equipment
Stump harvesting in Scandinavia is becoming more common. Their studies into stump
harvesting occurred in the 1970s and 1980s as a way to increase the amount of raw material for
the pulp industry. Their research has been renewed with the recent interest in bioenergy.
Because increased use of forest fuel requires larger and larger procurement areas, the inclusion
of stump material within shorter distances could make this resource more economical to harvest.
Stump harvesting is usually restricted to final harvests in Scandinavian countries. Hakkila and
Aarniala (2003) report that fuel yield from stumps can be as high as the yield from above-ground
residues. It is not typically implemented in thinnings because of the risk of damaging the
remaining trees in the stands.
Excavators are the typical equipment used for extracting stumps and root masses (Hakkila and
Aarniala, 2003; Vickery, 2008; and Henningsson, 2008). A boom-mounted attachment is used to
lift, then shear (or split) stumps into smaller pieces. Some operations use the attachment to pull
soil back into the hole in preparation for planting. Some boom attachments are manufactured
with a separate metal piece welded to the outside to aid in filling and smoothing the soil back
into the stump hole.
Many of the stump harvesting production references are for spruce, pine
and birch in Scandinavian countries. For stump lifting after a
regeneration harvest, lifting time increases as stump diameter increases
(Henningsson, 2008). Also, stump volume has a positive relationship
with stump diameter (Palander, 2009). On the other hand, stump
diameter has an inverse relationship with stump processing time (Laitila,
2008). These relationships are not as well documented in the United
States. The relationships between stump processing times and the
impacts of soil types on processing times are not known for many tree
species and soil type combinations in the United States. However, a late
1970s era publication (Sirois, 1977) tested a machine that was
commercially available at the time, a Rome THX Tree Extractor. With
this machine, researchers were able to shear the lateral roots of trees, and then extract the stumps
with an upward pulling action. In testing common hardwood species of the southern United
States (sweet gum (Liquidambar styraciflua L.), hickory (Carya spp. ) southern red oak (Quercus
falcata Michx), and white oak (Quercus alba L.)), researchers determined that the amount of
biomass available in the stump and in the main root mass was about 18% of the total above-
ground biomass available in each stem. Stems of up to 9 inches in dbh could be extracted fairly
easily, and red oaks were easier to extract than the other species. Trees were pulled from two
different soil types, but the significant variable for predicting the shearing and extraction forces
of the forest operation was dbh. Lateral root depth, coupled with the limited 10-inch shear depth,
impacted the ability to extract some stems by this machine. In general, the lateral root depths of
pine aren’t as deep as the hardwoods tested in this study.
Figure 1. Stump lifting
and splitting attachment
Smaller stump sizes in younger material may not
be economical to harvest. In the United States,
non-industrial forest lands that are being
converted to other uses are another opportunity to
harvest biomass from stump material. This
biomass can be in the form of large stumps, but
can also be found in standing younger trees.
When stumps are harvested from these younger
stands, loggers have used a whole-tree pulling
method rather than stump lifting. This requires a
different type of excavator attachment. A logger
in Georgia is using a demolition grapple for this
purpose. The excavator grips single trees or
multiple trees and pulls them out with the main
root mass attached.
Operator protection for worker safety is a concern when using excavators in forest operations.
Previous research by Rummer et al (2003) analyzed the rollover performance and thrown object
performance of hydraulic excavators and recommended improved standards to the International
Organization for Standardization (ISO). The current standard for self-propelled machinery for
forestry roll-over protective structures (ISO 8082: 2003) does not apply to machines having a
rotating platform with a cab and boom on the
platform.
A fledgling stump harvesting system in Finland is
comprised of an excavator for extraction, off-road
transport by forwarders, and special large-volume
trucks for transport to mobile or stationary
comminution equipment (Hakkila and Aarniala,
2003).
Forwarders are not as common in the United
States as they are in Europe. In ground-based
harvesting systems, in-woods transport is
typically accomplished by skidding. Skidding
stumps and split stumps is probably not the most
effective way to move the stump material to the logging ramp. Off-road transport would need
additional research to determine the best methods to be implemented in various regions of the
United States.
Two different stump harvesting systems have been observed in two locations in the southeastern
United States. In a land clearing operation in Alabama, stumps were lifted and split using an
excavator with a stump lifting and shearing attachment. No attempt was made to fill in the holes.
The split material was loaded onto off-road dump trucks to transport the material to a horizontal
grinder located in a log processing area of the land clearing. A trailer-mounted loader was used
Figure 2. Demolition grapple attachment
Figure 3. Whole tree harvesting with stumps
attached
to feed the material into a horizontal grinder. There wasn’t a planned time lag to allow for
transpirational drying of the biomass material.
In another land clearing operation in Georgia, pushed-over stump material and logging debris
from a recent clearcut was pushed into large piles with a brush blade mounted on a dozer. A
large horizontal grinder was moved to each debris pile where a trailer-mounted loader was used
to feed the grinder. Because of the large pile size, a wheeled log loader was also used to move
portions of the pile closer to the trailer-mounted loader, as needed.
Feedstock Quality
The typical Finnish consumers of stump biomass material are power plants that utilize fluidized
bed boiler technology (Laitila, 2008). Although fluidized bed systems can accept a broad range
of biomass specifications, there could be benefits from improving feedstock quality through
harvesting methods. Several of the previously described harvesting systems recommend shaking
the pieces of stumps before piling them in the harvesting area (Palander et al, 2009; AEBIOM,
2007) to release soil and stones from the biomass. This action should help decrease the ash
content of the biomass.
In Scandinavian countries, piles of split stumps are left in the harvesting area to dry before being
transported to roadside, and to allow rain to wash soil off of the roots. Once at roadside, they are
again piled for further drying and storage until needed (AEBIOM, 2007). Sometimes, these piles
are covered. This multi-stage process is believed to increase the feedstock quality by reducing
both the amount of impurities and the moisture content in the biomass material.
In Finland, stumps are left to mature in the ground before being lifted (Laitila et al, 2008).
During this maturation time, the cohesion between the roots and soil decreases. As larger roots
start to dry, shrink and decay, the forces required to lift the stumps decrease. The result of this
maturation time could be a reduction of soil in the biomass.
Blending at a delivery location is another way to improve the feedstock quality when using
stumps for biomass. By blending the stump biomass with other biomass deliveries, a more
homogenous and standardized product can be created.
Environmental Considerations
In Sweden, 30 years of study indicate that stump harvesting does not negatively impact the
growth of the next stand. Egnell et al (2007) suggest that stump forwarding should follow the
same path as used in the round timber extraction to limit soil impacts. Soil disturbance
associated with stump lifting can be exacerbated with clay soils. In clay soils, larger amounts of
soil loss can occur because it remains more firmly attached to roots. In the United Kingdom, the
stumps are stored over winter to help the site retain soil through the action of rainfall and freeze-
thaw (Forest Research, 2009). Apart from the obvious initial concerns regarding soil
disturbance, there are other environmental considerations related to stump harvesting.
A benefit of stump harvesting is that it can reduce the spread of some root fungi. For example,
some western United States species of conifers are susceptible to annosus root disease (Dekker-
Robertson et al, no date). The disease causes crown yellowing and thinning, and decayed wood.
When the roots of a healthy tree come in contact with diseased roots, the infection spreads.
Annosus can live for decades in large stumps. One recommended way to control the spread of
the disease is through stump extraction. Healthy stumps are also recommended for removal to
provide a buffer around the infected area.
Carbon sequestration is another concern that arises with stump harvesting. Soil contains more
carbon than the above-ground parts of the forest (Forest Research, 2009). Stump extraction can
involve extensive, localized, soil disturbance that can increase decomposition rates and related
carbon release from the soil. The impact of stump removal on carbon loss may be directly
related to the proportion of soil organic matter found in different soil types. Egnell et al (2007)
state that although a substantial amount of carbon is removed with logging residues and stump
harvesting, it is minor over a 60-90 year rotation period. Revegetation may promote carbon
sequestration that can help mitigate the negative effects on soil carbon loss. But, on land
clearing sites where the land use is changing, the carbon impact may not be mitigated by
revegetation. Research is needed to determine the relationship between carbon loss and soil
types found in the United States to better understand the environmental impacts of stump
removal.
Nutrient cycling is often cited as a concern from the removal of logging debris. This concern
may also extend to stump harvesting in the Untied States. The mitigation of stump removal
impacts on soil nutrients is addressed in a Finnish publication (Paananen and Kalliola, 2003). In
stump extraction, the area of soil disturbance is limited as much as possible around each stump.
After each extraction, the organic layer is covered with mineral soil to limit the release of
nutrients and heavy metals. In addition, about ¼ of stumps and the greater part of all roots are
left in the soil to benefit soil organisms.
The removal of stumps may have an impact on biodiversity. Stumps can provide a structural
shelter or an environment for insects, mosses and lichens. Research is needed to determine the
impact of stump removal on a variety of forest resources, and to develop guidelines on how to
mitigate negative environmental impacts of stump removal.
Summary
There are a variety of studies available regarding stump harvesting. Most of the recently
documented studies are in Scandinavia and Europe. Equipment is currently available in the
United States to accomplish many of the harvest system functions. Additional research is needed
to determine the impact of tree species, tree ages, soil types and other variables on feedstock
quality, production rates, and costs of stump harvesting in the United States. Information on the
environmental impacts of stump harvesting on a variety of forest resources is also needed.
References
AEBIOM. 2007. Procurement of Forest Residues. Accessed 5/15/09: http://www.aebiom.org/
IMG /pdf/Forest_residues_August2007.pdf
Dekker-Robertson, D., P Griessmann, D. Baungartner, and D. Hanley. Forest health notes:
annosus root disease. Washington State Univeristy Cooperative Extension, Department of
Natural Resources Sciences Extension. Pullman, WA. 3p.
Egnell, G., R. Hyvönen,L. Högbom, T Johansson, T. Lundmark, B. Olsson, E. Ring, and F. von
Sydow. 2007. Environmental aspects on stump-harvest – compilation of knowledge and
knowledge gaps. Energy Agency Report 40. 154 p. (in Swedish)
Forest Research. 2009. Stump harvesting: interim guidance on site selection and good practice.
The Research Agency of the Forestry Commission, United Kingdom. 18p.
Hakkila, P., and M. Aarniala. 2003. Efficient Technology for competitive production of forest
chips. The Finnish Wood Energy Technology Programme 1999-2003. 4p.
Henningsson, M.; T. Nordfjell, D. Athanassiadis and O. Lindroos. 2008. Stump-harvesting: Best
practice and 25 years old innovative approaches. Presented at the North Baltic
Conference on Forest Operations, Copenhagen, Denmark. Accessed 5/15/09 at:
http://www.sl.kvl.dk/upload/athanassiadis.pdf
Karlsson, J. 2007. Productivity at stump lifting. SLU Working Report 168. 53 p. Accessed
5/15/09 at: http://ex-epsilon.slu.se/archive/00001561/01/Arbetsrapport_168.pdf
Laitila, j., T. Ranta and A. Asikainen. 2008. Productivity of stump harvesting for fuel.
International Journal of Forest Engineering 19(2): 37-47.
Paananen, S., and T. Kalliola. 2003. Procurement of forest chips at UPM Kymmene from
residual biomass. UPM Kymmene and OPET Finland, VTT.
Palander, T, L. Vesa, T. Tokola, P. Pihlaja, and H. Ovaskainen. 2009. Modelling the stump
biomass of stands for energy production using a harvester data management system.
Biosystems Engineering 102: 69-74.
Rummer, R., S. Taylor, and M. Veal, 2003. New developments in operator protection for forest
machines. In: Proceedings of the 2nd International Forest Engineering Conference,
Vaxjo, Sweden. Pgs 60-66.
Sirois, D. 1977. Feasibility of harvesting hardwood trees by extraction. Proceedings of the 1977
American Society of Agricultural Engineers Winter Meeting. ASABE: St Joseph, MI.
18p.
Vickery, V. 2008. P & V Logging. Personal communication.
Proceedings of 2009 COFE: Environmentally Sound Forest Operations 32nd Annual Meeting of the Council on Forest Engineering
June 15-18, 2009 North Tahoe Conference Center, Kings Beach, California
Compiled by Bruce Hartsough and Bryce Stokes
Forest Operations (Tuesday, 9:00-10:20 am) Moderator – Daniel Guimier, Vice President, FPInnovations – FERIC Division Finding the ‘Sweet-Spot’ of Mechanised Felling Machines Rien Visser1*, Raffaele Spinelli2, Jacob Saathof3 and Simon Fairbrother4
Director1, Student3, and Assistant Lecturer4, Forest Engineering, University of Canterbury, Christchurch, New Zealand, and 2Head of Forest Operations Research, CNR, Sesto-Fiorentino, Italy Do Synthetic Ropes Change the Design Principles of Standing Skylines? Ewald Pertlik Department of Forest and Soil Sciences, Institute of Forest Engineering, University of Natural Resources and Applied Life Sciences, Vienna, Austria Development of a New Operation System With Carriages for Turn Back Yarding System Kazuhiro Aruga1*, Toshiaki Tasaka1, Akira Nishikawa2, and Toshihiko Yamasaki3 1Utsunomiya University, Utsunomiya, Japan, 2Kawasaki Machine Company, Kochi, Japan, 3Kochi Forest Technique Center, Kochi, Japan Efficiency and Ergonomic Benefits of Using Radio Controlled Chokers in Cable Yarding Karl Stampfer1, Thomas Leitner2, Rien Visser3* 1Head of School, and 2graduate student, Forestry Faculty, University of Agriculture and Life Sciences, Vienna, Austria, 3Director of Forest Engineering, Canterbury University, Christchurch New Zealand
The Human Factor (Tuesday, 10:40 am – 11:40) Moderator – Tetsuhiko Yoshimura, Shimane University, Matsue, Japan Understanding the Hazards of Thrown Objects: Incidents, Research and Resolutions John J. Garland, PE1* and Robert Rummer2 1Consulting Forest Engineer, Garland & Associates, Corvallis, OR, 2Project Leader, Forest Operations Research, USDA Forest Service, Auburn, AL Identifying Loggers’ Reactions and Priorities in an Increasingly Fragmented Landscape Matthew C. Moldenhauer1 and M. Chad Bolding2* 1Graduate Student, Department of Forestry and Natural Resources Clemson University, Clemson, SC and 2Assistant Professor of Forest Operations/Engineering, Virginia Tech, Department of Forestry, Blacksburg, VA